9002-2900/9002-2901 PAGE 1 9002-2900/9002-2901 Instructions 11-23-15

9002-2900/9002-2901 PAGE 1 9002-2900/9002-2901		Instructions	11-23-15
9002-2900/9002-2901
9002-2900/9002-2901Instructions11-23-15
PAGE 1
BHM
10/05/15
NTV-DOC204
Overview
The RAM MULTI-CAM interfaces up to 5 cameras & 1 Auxiliary A/V source to the OEM
RA4/RA3 8.4” uConnect media screen in 2013+ RAM vehicles. All connected cameras are
displayed through data using factory controls. Turn signal camera activation is speed adjustable
with programming from the factory radio controls/LCD cluster or NAV-TV USB Updater.
Rear View Cam
Turn Signal Cams
Auto Front Cam
AUX A/V
Cargo Cam
Control in Motion
Kit Contents
CAM Input
Harness
NTV-HAR267
Plug & Play T-harness
NTV-HAR265
MULTI-CAM Module
NTV-ASY222
USB Cable (updates)
NTV-CAB009
Optional Cameras available (Inculded with the 9002-2901)
Optional A/V switcher
(required for A/V input)
Camera 12 (front/rear)
NTV-KIT564
RAM-CAM
Rear camera
NTV-KIT426
Turn Signal-Cameras
NTV-KIT594
AVSW
NTV-KIT224
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
2|Page
PAGE 2
BHM
10/05/15
NTV-DOC204
RAM MULTI-CAM Connectors
24-PIN (Cameras & I/O) Connector
18-PIN (Plug & Play T- Harness) connector
PIN #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Description
12v (+) Constant
-Not Used-Not Used-Not Used-Not UsedCAN (1) HI (radio side)
CAN (0) HI (vehicle side)
DIFF (+) (radio side)
DIFF (+) (vehicle side)
Ground (-)
INPUT 2 (-) NOT USED
INPUT 1 (+) NOT USED
-Not Used-Not UsedCAN (1) LO (radio side)
CAN (0) LO (vehicle side)
DIFF (-) (radio side)
DIFF (-) (vehicle side)
Color
Yellow
Blue
Orange
--White/Black
Gray/Black
Orange
Blue
Black
Blue
Gray
--White
Gray
Orange/White
Blue/White
PIN #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Description
Shield for Reverse-CAM RCA
Shield for Front CAM RCA
Shield for Right Turn RCA
Shield for Left Turn RCA
Shield for AUX VID RCA
Shield for Cargo CAM RCA
Ground OUT
-Not Used-Not UsedINPUT 4 (NOT USED)
INPUT 3 Retrofit PDC Monitor
UART RX
Signal for Reverse-CAM RCA
Signal for Front CAM RCA
Signal for Right Turn RCA
Signal for Left Turn RCA
Signal for AUX VID RCA
Signal for Cargo CAM RCA
-Not Used-Not UsedOUTPUT 3 Retrofit PDC Power
OUTPUT 2 AUX AVSW TRIGGER
OUPTUT 1 12v ACC
UART TX
Wire Side
Wire Side
18-PIN
24-PIN
Color
Black
Black
Black
Black
Black
Black
White
White/Black
Purple
Pink
Brown/Black
Yellow
Yellow
Yellow
Yellow
Yellow
Yellow
--Red
Blue/Red
Gray/Red
Brown
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
3|Page
PAGE 3
BHM
10/05/15
NTV-DOC204
Dash Disassembly (RAM)
1. Remove the Torx t20 screw at the right rear of the pocket on the
right side of the dash.
2. Remove (2x) Torx t20 at the top of the dash. They are hidden beneath a rubber mat.
3. The face should be free now, pull straight
outwards (towards you) with medium force.
Use plastic panel tools if necessary.
4. Remove (4x) 7mm screws that secure the
LCD touchscreen.
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
4|Page
PAGE 4
BHM
10/05/15
NTV-DOC204
RAM MULTI-CAM Module Installation
1. After removing the factory radio, grab the provided Plug & Play T-harness and connect the
female side to the factory 44-pin plug. Make certain the lock connects together securely.
2. Install all cameras and run signal/power leads into the front dash opening.
Camera Installation Notes:
a. 12v ACC is provided from output 1 (PIN 23, gray/red). If connecting multiple
cameras, trigger a relay with this output instead to power your cameras!
b. Connect each camera signal to each yellow RCA per their specific labels (rear,
front, right TSC, left TSC etc).
c. The provided Plug & Play T-Harness contains red & black AUDIO RCA’s in the
center of the plug & play section. If not adding any AV source for this install,
connect these together (see diagram). If left disconnected, audio will not pass
through.
9002-2900
3. Optional: If installing aftermarket front sensors in addition to the MULTI-CAM,
connect the following wires for sensor-activated front-cam switching:
a. Connect the sensor main unit’s power wire to output 3 (PIN 21, pink) from the MULTICAM
b. Splice the sensor main unit’s speaker signal lead (+) to input 3 (PIN 11, brown) from the
9002-2900
MULTI-CAM
4. Optional: If adding an additional A/V source (AVSW required), connect the following:
a. Connect output 2 (PIN 22, blue) to the white/red wire from the AVSW (not included).
Ground the black wire from the AVSW.
b. Connect the video signal from the AUX A/V unit to the RCA on the MULTI-CAM labeled
‘AUX’ (video ports on the AVSW are NOT used)
c. Connect the audio signal from the AUX A/V unit to the A1 input of the AVSW. This may
require the provided adapter.
d. Connect the black & red RCAs located in the Plug & Play T-Harness to the appropriate
red & white ports on the AVSW (see diagram: pg. 9)
A1
AVSW
Car side
Radio side
Installation continues on next page…
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
5|Page
PAGE 5
BHM
10/05/15
NTV-DOC204
5. Optional: If the vehicle possesses both OEM cameras (reverse tailgate cam on the rearview
mirror and cargo cam on the main 8.4” screen), force both cameras to display on the main 8.4”
screen by completing the following:
a. Extend (splice, do not cut) the OEM tailgate signal with a pair of wires to the main radio
location. There are two easily accessible places for grabbing this RVC signal:
*Note: If the OEM tailgate RVC signal is cut in half, the rearview-mirror image will
display an error while in reverse. SPLICE into these wires, DO NOT CUT!
5.a.
Green/Orange:
RVC (-)
Green/Orange:
RVC (-)
OR
Green/Brown:
RVC (+)
Green/Brown:
RVC (+)
Driver’s side kick panel area
Passenger’s side, behind
side dash panel
b. From the MULTI-CAM’s
9002-2900’s 18-pin connector, locate (2x) 2-pin black plugs connected
together. Cut the connectors off (these would be used in a future revision of the MULTICAM).
c. Connect your extended pair of wires from step 5.a. to the 18-pin connector side of the
previously cut wires (green/orange to pin 18, green/brown to pin 9).
d. Extend the T-Harness side of the cut wires 9 & 18 (9 = [+], 18= [-]) with a single Male
RCA cable (not included) to the RCA labeled ‘Cargo Cam’ from the MULTI-CAM
9002-2900 24-pin
connector.
e. Make sure you set Cargo Cam to ‘FIX’ in NAVTV Settings while programming the MULTI9002-2900
CAM.
See Cargo Camera Connection diagram on next page for visual aid for Step 5.
9200-2900
6. Connect the RAM
MULTI-CAM module to the 18-pin & 24-pin connectors found in the Plug &
Play T-Harness.
7. Connect the male side of the Plug & Play to harness the monitor. Reconnect all other plugs to
the monitor and proceed to Programming on Page 10.
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
6|Page
PAGE 6
BHM
10/05/15
NTV-DOC204
Cargo Cam Connection Modification Diagram
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
7|Page
PAGE 7
BHM
10/05/15
NTV-DOC204
Installation Diagrams
RAM
Cameras Only
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
8|Page
PAGE 8
BHM
10/05/15
NTV-DOC204
RAM MULTI-CAM Programming
There are 2 different ways to program the RAM MULTI-CAM:
1. In the vehicle, with through the factory dash MUTE button, TUNING KNOB, and CLUSTER LCD
for feedback (true LCD cluster-equipped vehicles only), or
2. With a Windows PC, using the provided USB cable (any 13+ RAM with the 8.4” RA4/RA3
radio).
This page (below) and page 11 outline programming using the OEM vehicle controls (while module is
connected to the vehicle. See page 12 for programming using a Windows PC.
While in NAV-TV
settings mode only:
Rotate clockwise
(slowly, one
detent/time) to
scroll through
options. Press ENTER
to change setting.
Press and HOLD
(15 seconds) to
enter NAV-TV
settings mode
1. Before attempting to program, after making connections, let the vehicle perform a CAN-reset:
Close all doors/trunk/hood, lock the vehicle and waiting 5 minutes before proceeding to
program.
2. Turn the vehicle’s ignition on. Be certain you’re resting in FM
mode (see an FM station frequency on the cluster),
otherwise the cluster information may not display.
To show the FM source on the
cluster, first clear any messages
shown (door status, etc) with the UP
or DOWN arrows on the steering
wheel. Press the audio source
button until ‘FM’ is displayed.
Center button:
Change Audio Source
3. Close all doors (door status may override NAV-TV settings cluster feedback).
4. View the chart on the next page for settings descriptions and the diagram above to begin
programming.
5. NAV-TV programming mode will time out (back to factory) after 15 seconds. Scroll to the end of
the settings menu and select ‘EXIT’ to exit and save settings.
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
10 | P a g e
PAGE 9
BHM
10/05/15
NTV-DOC204
RAM MULTI-CAM Programming Parameters (OEM Cluster)
Programming
sequence
(cluster)
NAV-TV
Settings
Selection option
Description
TUNE-Next Item /
Enter Change
OEM / Retrofit
Force RVC
OFF / ON
Rotate TUNE knob to access different menus,
press knob inwards to enter/change setting
OEM: Vehicle possesses a manufacturer-installed
reverse camera.
Retrofit: Any aftermarket camera.
ON: Enables option of forcing RVC.*
F. CAM
OFF / ON
ON: Enables option of installed front camera.
RVC
PDC
OFF / ON / OEM
AUX VID
OFF / ON
Cargo CAM
OEM / ON / FIX
Turn CAM
OFF / ON
Turn Spd
Turn Rev
EXIT
ALL / 25 / 30 / 35
OFF / ON
OFF: Leave off if there are no sensors (OEM or
aftermarket)
ON: Set this option if adding aftermarket front
sensors (for auto front-cam switching)
OEM: Set this option if the vehicle has OEM front
sensors (for auto front-cam switching)**
ON: Enables option of AUX VIDEO
OEM: No Change.
ON: Emulates Cargo CAM menu.
FIX: Displays both OEM cameras on main 8.4”
display***
Activates Turn Signal Cameras
ALL: Turn Signal Cameras will display regardless
of speed.
25: TSCs will only activate > 25 mph
30: TSCs will only activate > 30 mph
35: TSCs will only activate > 35 mph
OFF: Reverse-cam image will take precedence
over TSCs
ON: TSCs will take precedence over reverse-cam
image
Exits programming mode and saves changes.
*Factory Rear camera is controlled via LIN. Forced OEM RVC is not supported with the MULTI-CAM.
**OEM Sensor-switching not available with this release. This feature is coming soon.
***Requires extending the tailgate camera signal from passenger side dash or drivers kick to the main
display. See page 6 step 5.
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
11 | P a g e
PAGE 10
BHM
10/05/15
NTV-DOC204
RAM MULTI-CAM Operation
AUX: Press & hold
(2 sec) to activate
Force front camera: Hold both
‘SCREEN OFF’ & ‘BACK’ (2 sec)
Force rear camera:
Press & hold (2 sec)
CIM: Hold
(3 sec) to
activate
Rear Camera Operation: Placing the vehicle in to reverse will automatically display
any connected camera. This image will take precedence over all other images
unless the ‘Turn Rev’ feature is set to ON in NAVTV Settings (this setting
makes Turn Signal Cameras overtake Reverse image).
Force Rear Camera: To force rear camera, press and hold radio ‘BACK’ button for 2
seconds. To exit forced rear camera, press and release radio ‘BACK’ button. Note:
forced rear camera is only supported on aftermarket cameras.
Force Front Camera: To force front camera, press and hold both radio ‘SCREEN OFF’
& ‘BACK’ buttons together for 2 seconds. To exit forced front camera, press and
release radio ‘BACK’ button.
Auto-Front PDC Camera: With ‘PDC’ enabled in NAVTV Settings (ON or OEM*), the
connected front camera will display any time the following is true:
a. The vehicle is in Drive
b. The vehicle is traveling < 7mph
c. The connected front parking sensors sense an obstacle
The radio will return to the factory image after the Parking Sensors no longer sense
an intrusion, or the vehicle reaches about 7mph.
*OEM Sensor-switching not available with this release. This feature is coming soon.
Activate Aux Video mode: To activate the AUX screen, press and hold radio ‘SCREEN
OFF’ button for 2 seconds. To exit AUX mode, press and release the ‘BACK’ button.
If using AUX video mode for an A/V source, the RCAs located on the Plug &
Play T-Harness must be opened up with an AVSW (KIT224, not included with
MULTI-CAM). See Page 5, Step 4.
2 seconds
2 seconds
2 seconds
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
13 | P a g e
PAGE 11
BHM
10/05/15
NTV-DOC204
MULTI-CAM Operation Continued
Cargo CAM: When Cargo CAM is set to ‘ON’ or ‘FIX’ in the
NAVTV Settings menu, the OEM Cargo Cam menu will be
emulated on the radio. This will allow the option for forcing
an added Cargo/Trailer/Baby camera (or displaying both on
the main screen). Press the ‘Cargo Camera’ button located
in the ‘Controls’ tab on the main radio screen to display the
camera connected to the Cargo CAM RCA.
If the user has and desires both OEM cameras
(Cargo CAM and Reverse CAM) to display on the
8.4” screen, additional installation is needed, see
Pg. 6, Step 5. The Cargo CAM option must be set to
‘FIX’ for this setup to work properly.
After activated, while the vehicle is in motion, the
OEM Cargo Camera will time out in about 5
seconds. For viewing the Cargo Camera for a longer
duration (3 mins), activate the CIM function. See
below.
If using this feature, you MUST perform a
full CAN reset (after programming) before
the menu will display!
Turn Signal Cameras: To display TSCs, simply use the turn
signals as you would normally and the connected image will
display either all the time (while in drive), or only after 25,
30 or 35 mph respectively, depending on what was set in
MULTI-CAM programming.
If the user desires TSC images to take precedence
over the reverse, this option must be enabled in
NAVTV Settings (Turn Rev = ON).
Additionally, the user may use a “bump method” to
view the TSC quickly. Toggling the turn signal level
quickly (just enough to engage the bulb) will display
the TSC image for 3 seconds.
Activate CIM (Control in Motion): To activate CIM for
factory navigation, press and hold the ‘Volume’ button for 3
seconds (CIM will disable automatically after 3 minutes).
This function will also keep the Cargo Camera enabled for 3
minutes, and will reset upon every key cycle.
NOTE: Activating the CIM function will NOT bypass video in
motion at this time, if equipped.
3 seconds
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
14 | P a g e
PAGE 12
BHM
10/05/15
NTV-DOC204
FAQs
Q1. I can’t get into programming mode.
A1. Turn off the vehicle and remove the key. Close all points of entry and use the remote to lock
the vehicle. Wait approx. 5 minutes without opening or disturbing the vehicle. Unlock and cycle the
ignition to the ‘RUN’ position. Make certain that the cluster is in FM radio mode before you begin
programming; and no errors are displayed (door open, etc), otherwise the cluster information might not
display. Hold down the “MUTE” button until you see the display options post on the cluster.
Q2. When I try to force (front, rear) camera, nothing happens.
A2. Make certain you’ve enabled the options you want to use in the NAVTV settings mode and
that you scrolled to the end and selected ‘EXIT’ (or it will not save).
Q3. I hear no audio when my auxiliary source is playing on screen.
A3. Verify that the audio RCAs are connected properly to the AVSW.
Q4. Everything works properly, but when an audio source is connected to the 3.5mm audio jack,
there’s no audio.
A4. Make sure the audio RCAs are connected together on the Plug & Play harness.
Q5. When I place the vehicle into reverse, I get a black or blue screen.
A5. Make sure the camera is getting sufficient power and the RCA is connected to the proper
yellow RCA on the 24-pin harness.
Q6. The camera image is displayed properly when the vehicle is in reverse, but there’s only a black or
blue screen when the camera is forced.
A6. Make sure the camera power is not connected to the reverse lamps. Camera power needs to
be connected to an accessory wire (cigarette lighter). If the camera is OEM, forcing it to display in any
gear is not supported.
Other MULTI-CAM Notes:
When multiple cameras are connected, the MULTI-CAM will clear back to the factory image
after 3 cameras have been forced in succession. This is normal. I.E: If you had AUX mode
displayed on screen, turned the left turn signal on (which will display), then rolled up to an
obstacle which forced the front camera, placing the vehicle into park will then display the
factory image (will not return to AUX image automatically).
Cluster feedback only displays while programming (NAVTV Settings).
Cargo Camera usage will only display for about 8 seconds when in motion, then will time out
(this is a factory limitation). Activating the CIM feature will retain this image for 3 minutes if
desired.
When setting Cargo Cam to ‘ON’ or ‘FIX’, you must let the vehicle perform a full CAN reset, after
programming, before the menu will display properly.
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for
misuse of its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is
intended for off-road use and passenger entertainment only.
15 | P a g e
PAGE 13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement