QL025 Manual-EN
QL025
Owner’s Manual
Laundry Kit
With flex-neck faucet
and storage cabinet
Thank you for choosing Presenza Italia!
We appreciate the trust and confidence you have placed in
Presenza Italia through the purchase of this laundry kit.
1
ATTENTION:
Parts Included
Carefully check the unit prior to installation
to ensure there is no damage. Do not dispose
of any packaging until you are satisfied with
this product. If you have any problems with
this product or there are missing or damaged
parts, please call toll free:
B
A
1-877-333-0098
D
C
(Monday to Friday, 8:30 am to 5 pm, EST)
DO NOT RETURN THE UNIT TO THE PLACE
OF PURCHASE BEFORE CALLING THE
TOLL FREE NUMBER ABOVE.
1. Your installation must comply with all
local plumbing building codes. Have a
qualified tradesman do or approve your
plumbing installation.
2. Please read and save this guide before
using this product. Store the guide in a
safe place so you will know where it is
when you want to refer to it.
WARNING: Always wear safety
goggles and gloves in order to
avoid any personal injuries.
E
F
G
H
I
[A] Cabinet.......................................................... 1 pc
[B] Sink................................................................. 1 pc
[C] Faucet assembly....................................... 1 pc
[D] Strainer assembly.................................... 1 set
[E] Door knobs............................................... 2 pcs
[F] Cabinet feet.............................................4 pcs
[G]Door knobs screws................................ 2 pcs
[H]Cabinet feet screws............................ 16 pcs
[I] Allen wrench............................................... 1 pc
Tools and Materials Required
Adjustable wrench
Pliers
Phillips screwdriver
Plumbers putty / sealant
Hacksaw
Utility knife
Carpenters level
Tail pipe
Supply lines (2)
Masking tape
Safety goggles
2
Cabinet Installation
Door Position Adjustment
If the doors need to be repositioned, the
hinges can be adjusted to ensure a precise
fit with the cabinet.
H
F
A
1
2
3
1. Lateral adjustment of the screws adjust
the door left or right.
1
1. Unpack the unit and place the sink [B]
on a blanket or cardboard to protect
the surface.
2
3
2. Horizontal adjustment of the screws
adjust the door forward or backward.
2. Turn the cabinet [A] upside down onto
the protective surface.
3. Gently put each cabinet feet [F] onto its
proper location. Using four
1 cabinet feet 2
screws [H] per cabinet foot, attach the
cabinet foot [F] to the bottom of the
cabinet [A].
4. Gently place cabinet upright.
CAUTION: Do not place side load
onto feet when righting cabinet.
3
3. Vertical adjustment of the screws adjust
the door up or down.
Faucet Installation
1. Carefully take out all the parts of the
faucet assembly [C]. The faucet is preassembled, except for the sprayer head.
E
G
2. Take the washer, gasket and retaining
ring off of the faucet body.
3. Place the faucet body carefully
through the hole in the sink [B]. A
second person may be required to
hold the body in place until the faucet
installation is complete.
6. Insert the door knob screw [G] into the
pre-drilled hole on each door. Attach
the door knob [E] and tighten the door
knob screw [G]. Repeat on other door.
3
Plumber’s putty
or sealant
Strainer
body
Gooseneck pipe
Sprayer
head
Strainer
basket
Strainer
body
Faucet handle
Faucet body
Gasket
Retaining ring
Rubber
gasket
Washer
Friction
washer
Threaded section
Screws
Locknut
Plastic
flange
4. From underneath, slide the gasket and
washer and screw the retaining ring
over the end of the copper pipe and
up to the exposed threaded section of
the faucet. Tighten the retaining ring by
hand until it is snug. Using a wrench or
pliers, tighten the assembly.
5. Gently tighten the two screws on the
retaining ring. Do not over tighten.
6. Screw the sprayer head onto the
gooseneck pipe.
7. Connect the water supply line (not
supplied) to the faucet.
Tail pipe
(not supplied)
Connecting nut
3. Connect the plastic flange and tail
pipe (not supplied), then thread the
connecting nut through the tail pipe and
plastic flange up to the lower threaded
part of the strainer body. Tighten the
connecting nut by hand.
Sink Installation
1. Carefully place a bead of sealant all
around the top of the cabinet [A].
Strainer Installation
1. Apply a ring of plumber’s putty or
sealant (not included) to the underside
of the flange on the strainer body. Insert
the strainer body into the utility sink [B].
B
2. Assemble the rubber gasket, friction
washer and locknut onto the strainer
body from underneath the utility sink.
Hand tighten the locknut.
CAUTION: Do not over tighten the
locknut or the connecting nut, as
this may split or deform the strainer
body.
Sealant
A
2. Ease the sink [B] into the cabinet [A],
ensuring that it is placed evenly and is
centered on the cabinet. Wipe off any
excess sealant. Use masking tape to
hold the sink in place until the sealant
dries.
Placement
Move the assembled unit to the final
location. If required, level the unit by
adjusting the cabinet feet [F].
Care and Maintenance
CARTRIDGE REPLACEMENT
To replace the cartridge, please follow
these steps:
WARNING: Before proceeding, turn
off the water supply to the faucet.
Water temperature sign
Rings
Screw
Cap
Cartridge
Handle
body
F
Faucet body
1. Take off the plastic water temperature
sign by hand, then use the Alen wrench
[I] to take out the screw and pull out
the handle body. The top lever of the
cartridge will be exposed.
2. Unscrew the cap and rings, making sure
not to damage the threads.
3. Pull out the cartridge and replace it with
a new 35 mm (1.4) ceramic cartridge.
4. Replace the rings and the cap.
5. Place the handle body on the cartridge.
Lock the screw back onto the handle
body and tighten it with the Allen
wrench [I]. Do not over tighten.
6. Put the plastic water temperature sign
back into the hole, make sure that red is
on the left and blue is on the right.
7. Slowly open the water feed to the
faucet to test.
Supply Line Assembly
The supply lines, which attach the faucet
to the household water system, are not
supplied with this unit. They need to be
purchased separately. Follow the supply
line manufacturer’s instructions for proper
installation.
CLEANING YOUR SINK
To maintain the smooth, high gloss surface
of your sink, follow these tips:
• Use common household cleaners (nonabrasive) or a mild liquid dish washing
detergent. Rinse well and dry with a
clean cloth.
• Do not allow any food, detergent, soap or grease to dry or sit for extended periods of
time on the surface of the sink.
• Never use abrasive cleaning products as they will dull and scratch the finish.
• Do not use scouring pads on the sink as they will dull the mirror finish.
• Never use steel wool pads as they will leave iron particles on the sink, which will cause
corrosion.
• Never leave steel or cast iron pans in your sink for extended periods of time as this can
cause corrosion.
Replacement Parts
If you are missing or require replacement parts, please call customer service at
1‑877‑333‑0098 (Monday to Friday, 8:30 am to 5:00 pm, EST). Identify the required part(s)
and have the replacement code ready when you call.
Part name
Code
Door knobs
QHL103
2
Door knob screws
QHL104
2
Cabinet feet
QHL105
4
Cabinet feet screws
QHL106
16
Door hinges
QHL102
4
Ceramic cartridge
QHS121
1
Faucet sprayer head
QHS107
1
Strainer assembly including
rubber gasket & washer
QHS103
1
Strainer basket
QHS101
1
6
Illustration
Quantity
One Year Limited Parts and Finish Warranty
This utility sink with faucet and cabinet is warranted to the original purchaser to be free of
defects in material and workmanship for one (1) year from the date of purchase.
Our obligation shall be limited to the repair or replacement of a unit (at our discretion)
that may prove, by our sole examination, to be defective under normal use and service
during the warranty period. We may issue credit in the amount of the invoice value of the
defective product (or a percentage of it according to use) in lieu of repair or replacement.
Any failure of this product that is not traceable to a defect in material or workmanship, is
not covered by this warranty. These non-warranty items include, but are not limited to:
• Change in colour or finish due to chemical usage.
• Damage due to the use of steel wool on the stainless steel surface.
• Improper installation not in accordance with manufacturer’s instructions.
• Dents, bumps, and scratches incurred during shipping, handling, or installation.
• Damage caused by failure to follow care and cleaning guidelines.
• Alterations made to the unit by the purchaser or installer.
• Damage caused by accidental impact, fire, flood, freezing, or normal wear.
• Bends and warping caused by forced connections, over-tightened fittings, or inadequate
support during installation.
A thorough inspection must be made before installation and any damage must be
promptly reported. We will not be liable for failures or damage that could have been
discovered or avoided by proper inspection and testing prior to installation.
Incidental repairs that would involve a minimum of time and effort on behalf of the
purchaser will not be considered warranty work and no compensation will be deemed
forthcoming.
This warranty is non-transferable and shall be voided if the unit is removed from its initial
installation, or if it is not installed following the manufacturer’s instructions.
Under no circumstance shall we be held liable for personal injury or property damage
resulting from improper installation or use of this product. We will not be held liable
for inconvenience caused by loss of use of this product, costs incurred for labour or
materials, removal and installation of replacement units, or any other incidental or
consequential damages. Costs relating to obtaining access for repair or replacement are
the responsibility of the user.
This warranty does not extend to commercial and institutional installation or use.
Warranty Claim Procedure
If a claimable defect occurs, please call customer service at 1‑877‑333‑0098
(Monday–Friday, 8:30 am–5:00 pm, EST) or email us at [email protected]
Prior to calling, please ensure you have:
• Model number or description of the utility sink kit.
• Proof of sale.
• Details regarding the defect.
• Name(s) and address(es) of the owner and installer.
Claims must be filled out in writing and returned within six (6) months of the appearance
of a defect. Failure to comply with this stipulation will make this warranty null and void.
We reserve the right to a 30 day delay following the receipt of a claim in which to inspect
the product. We assume no responsibility for labour costs, removing or replacing a
previously installed product, transportation, or the return of a product.
7
Imported by
St-Laurent, Québec, H4S 2C3
1-877-333-0098
www.conglomkb.com
Made in China
8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement