PFS US C Models
Installation and Operation Instructions
Superior™ Outdoor Wood Burning Fireplace
P/N 127008-01 Rev. B 10/2014
PFS
C
P127008-01
Models
®
US
REPORT NO. F09-095
WRE6036RS
WRE6036IS
WRE6036RH
WRE6036IH
WRE6042RS
WRE6042IS
WRE6042RH
WRE6042IH
WRE6050RS
WRE6050IS
WRE6050RH
WRE6050IH
SAVE THIS BOOK
This book is valuable. In addition to instructing you on how to install and maintain your appliance, it also contains
information that will enable you to obtain replacement parts or accessory items when needed. Keep it with your other
important papers.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
This wood burning fireplace complies with
UL127 CAN/ULC-S610-M87 standard as a
FACTORY BUILT FIREPLACE.
Installateur : Laissez cette notice avec l’appareil.
Consommateur : Conservez cette notice pour consultation ultérieure.
Ce foyer au bois est conforme aux UL 127 CAN/ULCS610-M87 norme comme une USINE CONSTRUITE
CHEMINÉE.
This fireplace is approved for use as a wood burning fireplace or for use with a vented gas log approved to
ANSI Z21.60 or Z21.84 standards or for use with a vent-free gas log heater approved to ANSI Z21.11.2 standard.
FOR CANADA: The authority having jurisdiction POUR LE CANADA: L’autorité compétente (comme le
(such as the municipal building department, fire service municipal du bâtiment, les pompiers, etc.) doit
department, etc.) should be contacted before
être contacté avant l’installation afin de déterminer la
installation to determine the need to obtain a
nécessité d’obtenir un permis.
permit.
This appliance may be installed in an aftermarket permanently located, manufactured home (USA only)
or mobile home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated
on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.
WARNING: If the information in these
AVERTISSEMENT : Assurez-vous de bien suivre les
instructions is not followed exactly, a fire or
instructions données dans cette notice pour réduire au
explosion may result causing property damage, minimum le risque d’incindie ou d’explosion ou pour éviter
personal injury or death.
tout dommage matériel, toute blessure ou la mort.
—— Do not store or use gasoline or other
—— Ne pas entreposer ni utilizer d’essence ni d’autres
flammable vapors and liquids in the vicinity
vapeurs ou liquides inflammables dans le voisinage
of this or any other appliance.
de cet appareil ou de tout autre appareil.
—— WHAT TO DO IF YOU SMELL GAS:
—— QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :
• Do not try to light any appliance.
• Ne pas tenter d’allumer d’appareil.
• Do not touch any electrical switch; do not
• Ne touchez à aucan interrupteur. Ne pas vous
use any phone in your building.
servir des téléphones se trouvant dans le bâtiment
où vous trouvez.
• Immediately call your gas supplier from
a neighbor’s phone. Follow the gas
• Appelez immédiatement votre fournisseur de
supplier’s instructions.
gaz depuis un voisin. Suivez les instructions du
fournisseur.
• If you cannot reach your gas supplier, call
the fire department.
• Si vous ne pouvez rejoindre le fournisseur de gaz,
appelez le service des incindies.
—— Installation and service must be performed
by a qualified installer, service agency or the —— L’installation et l’entretien doivent être assurés par un
gas supplier.
installateur ou un service d’entretien qualifié ou par
le fournisseur de gaz.
For more information, visit Superiorfireplaces.US.com
TABLE OF CONTENTS
Thank you for your purchase. We appreciate your
business!
Please carefully read and follow all instructions in this manual. Pay
special attention to all warnings and safety information.
Following these safety, care, and operation instructions will help
ensure many years of dependable and enjoyable service from your
fireplace.
Register your product online today!
To help us keep you up-to-date on product information and
offers, please take a few moments to register your product online at Superiorfireplaces.US.com (Owner Resources/Product
Registration).
Please read and understand these instructions before installing
or operating.
Safety..............................................................................................2
Specifications..................................................................................3
Fireplace Installation.......................................................................6
Venting Installation.........................................................................8
Firebrick Wall Installation..............................................................13
Optional Gas Line Installation.......................................................15
Glass Door Installation..................................................................16
Operation and Maintenance Guidelines.........................................17
Technical Service..........................................................................18
Replacement Parts........................................................................18
Parts.............................................................................................20
Accessories...................................................................................25
Warranty.......................................................................................27
SAFETY
WARNING: Improper installation, adjustment,
alteration, service or maintenance can cause injury
or property damage. Refer to this manual for correct
installation and operational procedures. For assistance or additional information consult a qualified
installer, service agency or the gas supplier.
IMPORTANT: Check local codes before installing this
fireplace.
Before beginning the installation of the fireplace, read these instructions through completely.
• This INNOVATIVE HEARTH PRODUCTS, LLC (IHP) fireplace and
its components are safe when installed according to this installation manual. Unless you use IHP components, which have been
designed and tested for the fireplace system, you may cause a
fire hazard.
• The IHP warranty will be voided by and IHP disclaims any responsibility for the following actions.
a.Modification of the fireplace, components, doors, air inlet
system and damper control.
b.Use of any component part not manufactured or approved by
IHP in combination with an IHP fireplace system.
Proper installation is the most important step in ensuring safe and
continuous operation of the fireplace. Consult the local building codes
as to the particular requirements concerned with the installation of
all factory built fireplaces.
2
WARNING: Do not install a fireplace insert in this
box unless the manufacturer's instructions with the
insert specifically state this fireplace has been tested
for use with this insert.
FOR YOUR SAFETY
•Do not store or use gasoline or any other flammable
vapors or liquids in the vicinity of this or any other
appliance.
•Due to high temperatures, the appliance should be
located out of traffic and away from furniture and
draperies.
•Do not place clothing or other flammable materials
on or near the appliance.
•Never leave children unattended when a fire is
burning in the fireplace.
WARNING: Use solid wood or processed solid fuel
firelogs only. When processed wood fuel fire logs are
used, do not poke or stir the logs while they are burning.
Use only fire logs that have been evaluated for the application in fireplace and refer to fire log warnings and
caution markings on packaging prior to use.
This fireplace is not intended to be used as a substitute
for a furnace to heat an entire home. Use for supplemental heat only.
Superiorfireplaces.US.com
127008-01B
SPECIFICATIONS
36" MODEL
29"
22 1/2"
14 1/2"
22 1/2"
19"
26 /8"
5
15 /8"
20 1/4"
(Ref.)
5
35 1/4"
4 1/2"
1 1/4"
36" HEARTH
11"
OUTSIDE AIR
ACCESS
67"
61"
49"
58"
GAS LINE
ACCESS
30"
7"
1"
1"
36"
45 1/8"
10 1/2" 9 1/2"
3 1/2"
4 1/2"
7 1/4"
11"
15 1/4"
Figure 1 - 36" WRE6036RS, WRE6036IS, WRE6036RH and WRE6036IH
127008-01B
Superiorfireplaces.US.com
3
SPECIFICATIONS Continued
42" MODEL
30 1/2"
22 3/4"
15 3/4"
26 3/8"
21 3/4"
23"
(Ref.)
29"
17 5/8"
41 3/8"
1 1/4"
42" HEARTH
4 3/8"
5/8"
OUTSIDE
AIR
ACCESS
11"
67" 58"
61"
49"
GAS LINE
ACCESS
30"
10 1/2" 9 1/2"
3 1/2"
7"
1"
42"
51 1/8"
4 1/2"
81/2"
13"
17"
Figure 2 - 42" WRE6042RS, WRE6042IS, WRE6042RH and WRE6042IH
4
Superiorfireplaces.US.com
127008-01B
SPECIFICATIONS Continued
50" MODEL
38 1/2"
24"
19 1/4"
34 3/8"
21 3/4"
28 1/2"
17 5/8"
49 3/8"
OUTSIDE
AIR
ACCESS
11"
61"
1 1/4"
50" HEARTH
43/8"
67"
23"
(Ref.)
GAS LINE
ACCESS
58"
49"
30"
10 1/2"
7"
1"
50"
59"
4 1/2"
9 1/2"
3 1/2"
8 1/2"
13"
17"
Figure 3 - 50" Models WRE6050RS, WRE6050IS, WRE6050RH and WRE6050IH
127008-01B
Superiorfireplaces.US.com
5
FIREPLACE INSTALLATION
SELECTING LOCATION
To determine the safest and most efficient location for the fireplace,
you must take into consideration the following guidelines:
1. The location must allow for proper clearances (see Figures 4 and
5).
2. Consider a location where fireplace will not be affected by drafts,
air conditioning ducts, windows or doors.
3. A location that avoids cutting of joists or roof rafters will make
installation easier.
4. An outside air kit is available with this fireplace (see Optional
Outside Air Kit on page 8).
6. Using screws or nails, secure fireplace to framing through flanges
located on sides of fireplace.
Note: For outdoor installations, fireplace enclosure must allow for
adequate drainage and fresh air ventilation. It is recommended that
a sealed, corrosion resistant catch pan with provision for drainage
be installed under fireplace within fireplace enclosure.
MINIMUM CLEARANCE TO COMBUSTIBLES
Back and sides of fireplace 1 1/2" min.
Ceiling 42" min.
Front of fireplace 48" min.
Floor**
0" min.
Perpendicular wall to opening 18" min.
36" Models 12" min.
Top spacers 0" min.
Mantel clearances
see Mantels, page 7
Chimney outer pipe surface 2" min.
36" Model 1" min.
* Not required at nailing flanges
** See step 2 of Framing
WARNING: Do not pack required air spaces with
insulation or other materials.
67.125"
58.125"
45.25" (36" Models)
51.25" (42" Models)
59" (50" Models)
Figure 4 - Framing Dimensions
Maintain 1 1/2"
Clearance
at Sides and
Back of Fireplace
61" (36" Models)
65" (42" Models)
71" (50" Models)
Minimum/Maximum Chimney Height for Residential Installation
Minimum height of chimney, measured from base of fireplace to flue
gas outlet of termination, is 16 feet for straight flue or a flue with one
elbow set. Maximum distance between elbows is 6 feet. For systems
with two elbow sets, minimum height is 22 feet. Maximum height of
any system is 50 feet. This measurement includes fireplace, chimney
sections and height of termination assembly at level of the flue gas
outlet (see Figure 15, page 11).
FRAMING
1. Frame opening for fireplace using dimensions shown in Figures 4
and 5.
2. If fireplace is to be installed directly on carpeting, tile (other than
ceramic) or any combustible material other than wood flooring,
fireplace must be installed upon a metal or wood panel extending
full width and depth of fireplace.
3. Set fireplace directly in front of this opening and slide unit back
until nailing flanges touch side framing.
4. Check level of the fireplace and shim with sheet metal if necessary.
5. Before securing fireplace to prepared framing, ember protector
(provided) must be placed between hearth extension (not supplied) and under bottom front edge of fireplace to protect against
glowing embers falling through. If fireplace is to be installed on a
raised platform, a Z-type ember protector (not supplied) must be
fabricated to fit your required platform height. Ember protector
should extend under fireplace a minimum of 1 1/2". Ember protector
should be made of galvanized sheet metal (28 gauge minimum to
prevent corrosion.
6
30.125"
28.250" (36" Models)
Superiorfireplaces.US.com
1 1/2" Clearance
Not Required at
Nailing Flanges
86.5" (36" Models)
92" (42" Models)
100" (50" Models)
Figure 5 - Corner Installation
127008-01B
FIREPLACE INSTALLATION Continued
Fireplace Front
Seal Gap
Ember Protector
Fireplace Front
Raised Hearth
Ember Protector
Fireplace Front
Elevated
6"
Ref.
Hearth
Extension
Seal Gap
Ember Protector
Combustible
Material
12 1/4" Ref.
15" Min. (36" Models)
21" Min. (42/50"
Models)
WARNING: Hearth extension is to be installed only
as shown in Figure 6.
MANTELS
A mantel may be installed if desired (see Figure 7). Woodwork such as
wood trims, mantels or any other combustible material projecting from
front face must not be placed within 12" (36" Models) or 18" (42/50" Models) of fireplace opening. Combustible materials above 12" (36" Models)
or 18" (42/50" Models) and projecting more than 1 1/2" from fireplace
must not be placed less than 15" (36" Models) or 21" (42/50" Models)
from the top opening of the fireplace (NFPA STD 211, Sec. 7-3.3.3).
Mantels or any other combustible material also may come up to side
edge of black metal face of fireplace as long as projections from front
face fall within limit shown in Figure 7.
Safe
Zone for
Projection of
Combustible
Materials
33°
3" Nom.
11/2" Max.
12" Min.
(36" Models)
18" Min.
(42/50"
Models)
HEARTH EXTENSION
A hearth extension projecting a minimum of 20" in front of and a
minimum of 12" beyond each side of fireplace opening is required
to protect combustible floor construction in front of fireplace. Fabricate a hearth extension using a material which meets the following
specifications: a layer of noncombustible, inorganic material having a
thermal conductivity of K=0.84 BTU IN/FT, HR. F (or less) at 1" thick.
For example, if the material selected has a K factor of 0.25, such as
glass fiber, the following formula would apply:
0.25 x 1.0" = 0.30" thickness required
0.84
Thermal conductivity "K" of materials can be obtained from manufacturer or supplier of noncombustible material. If hearth extension is
to be covered, use noncombustible material such as tile, slate, brick,
concrete, metal, glass, marble, stone, etc. Provide a means to prevent
hearth extension from shifting and seal gap between fireplace frame
and hearth extension with a noncombustible material (see Figure 6).
Upper
Section of
Fireplace
Fireplace Opening
Top View of Fireplace
7.75" (36" Models)
11.5" (42/50" Models)
FIREBOX
SAFE ZONE
Figure 6 - Hearth Extension
33°
Min. to
Perpendicular
Side Wall
12" - 36" Models
18" - 42/50" Models
3" Max.
4.5"
Combustible
Material Must
Not Overlap
Front Face
Figure 7 - Mantel Clearances to Combustible Material
127008-01B
Superiorfireplaces.US.com
7
VENTING INSTALLATION
OPTIONAL OUTSIDE AIR KIT (MODEL AK4/AK4F)
PART NO.
Signature
12-12DM
12-12HT
18-12DM
18-12HT
24-12DM
24-12HT
36-12DM
36-12HT
48-12DM
48-12HT
RLT-12D
RLT-12HT
The installation of an outside air kit should be performed during
the rough framing of the fireplace due to the nature of it's location.
Outside combustion air is accessed through a vented crawl space
(AK4F) or through a sidewall (AK4).
CAUTION: Combustion air inlet ducts shall not
terminate in attic space.
The maximum height for the air vent can not exceed
3 feet below the flue gas outlet of the termination.
Secure to Collars with Metal Tape,
Screws or Straps (Min. of 1/4" x 20"
in size)
Air Inlet
Location
Must Allow
For Bushes
or Snow
STL-12D
LINEAL GAIN
DESCRIPTION
Fireplace
GAIN
66 1/2"
Pipe Section
10 5/8"
Pipe Section
16 5/8"
Pipe Section
23 5/8"
Pipe Section
34 5/8"
Pipe Section
46 5/8"
Round Termination
Square ChaseTop with Slip
Section
7 3/4"*
7" to 15"*
* The lineal gain for the terminations is measured to
the flue gas outlet height.
15" Galvanized
Outer Pipe
Air Inlet
Eyebrow
Vent Hood
Vented Crawl Space
Required for
(Check Local Codes
Wall Installation
Before Installing in a
Vented Crawl Space)
12 3/8"
Stainless
Inner Pipe
Hemmed
End
Figure 9 - Lineal Gain
Figure 8 - Outside Air Kit
ASSEMBLY AND INSTALLATION OF DOUBLE WALL CHIMNEY
SYSTEM
CHIMNEY PIPE
The IHP chimney system consists of 12", 18", 24", 36" and 48" snaplock, double-wall pipe segments, planned for maximum adaptability
to individual site requirements. Actual lengths gained after fitting
overlaps must be taken into consideration (lineal gain) and are
given in the lineal gain chart (see Figure 9). Lineal Gain is the actual
measurable length of a part after two or more parts are connected.
For Canada, use chimney parts designated "HT".
WARNING: The opening in the collar around the
chimney at the top of the fireplace must not be obstructed. Never use blown insulation to fill the chimney
enclosure.
8
Each double wall chimney section consists of a galvanized outer pipe, a
stainless steel inner flue pipe and a wire spacer. The pipe sections must
be assembled independently as the chimney is installed. When connecting chimney directly to the fireplace, the inner flue pipe section must be
installed first with the lanced side up. The outer pipe section can then
be installed over 5 the flue pipe section with the hemmed end up. Press
down on each pipe section until the lances securely engage the hem on
the fireplace starter. The wire will assure the proper spacing between the
inner and outer pipe sections.
Continue to assemble chimney sections as outlined above, making
sure that both the inner and outer pipe sections are locked together.
When installing double wall snap-lock chimney together, it is important to assure the joint between the chimney sections is locked. Check
by pulling chimney upward after locking. The chimney will not come
apart if properly locked. It is not necessary to add screws to keep the
chimney together (exception, see Figure 10, page 9).
Superiorfireplaces.US.com
127008-01B
VENTING INSTALLATION Continued
OFFSET
A
4 3/8"
9 3/4"
12 3/4"
15"
18"
21 1/4"
23 3/4"
27 3/4"
30"
33"
36"
38 1/4"
41 1/4"
45"
46 3/4"
51"
53 1/4"
56 1/4"
59 1/4"
61 3/4"
64 3/4"
68 1/4"
70"
74 1/4"
76 3/4"
79 3/4"
RISE
B
16 3/8"
25 1/2"
30 3/4"
34 3/4"
40"
46 1/4"
49 1/4"
56 3/4"
60 3/4"
66"
71"
75"
80 1/4"
86 3/4"
89 1/2"
97"
101"
106 1/4"
111 1/2"
115 1/2"
120 3/4"
127"
130"
137 1/2"
141 1/2"
146 3/4"
CHIMNEY LENGTH
12" 18" 24" 36" 48"
ELBOW SET ONLY
1
1
1
1 1
1
1 1
1
1
1
1
1
1
2
1 1
1
2
1 1
1
1 1
2
2
1
1 1
1
2
1
2
2 1
1 1
2
1
2 1
1
2 1
4
USING ELBOW OFFSETS (30E-12DM)
1. To achieve desired offset, you may install combinations of 12",
18", 24", 36" and 48" length of double wall pipe (see offset chart
and Figure 10).
2. Chimney weight above offset rests on return elbow. Straps must
be securely nailed to rafters or joists (see Figure 11, details A and
B).
3. Maximum length of pipe between supports (return elbow or
12S-12DM) is 6' of angle run. Maximum of two 6' angle run
sections per chimney system (see Figure 12, page 10).
4. All pipe connections between the offset and return must be
secured with two screws on the outer pipe only (see Figure
10). Do not penetrate the inner stainless.
See Detail A
2" Min.
Straps
Straps
Detail B
Angle Firestop
See Detail B
OFFSET CHART (22-50 FT. SYSTEM HEIGHT)
Straps
Straps
Detail A
Return Elbow
Figure 11 - Ceiling Support Pipe 12S-12DM
Screws
B
CAUTION: THE STRUCTURAL INTEGRITY OF THE
MANUFACTURED HOME FLOOR, WALL, AND CEILING/
ROOF MUST BE MAINTAINED.
WARNING: DO NOT INSTALL IN SLEEPING ROOM
OF MOBILE HOMES.
A
Figure 10 - Elbow Offset
127008-01B
Superiorfireplaces.US.com
9
VENTING INSTALLATION Continued
Return
Elbow
Offset
Elbow
Return
Elbow
Offset
Elbow
6' Max.
Return
Elbow
6' Max. Ceiling
Support Pipe
12S-12DM
Return
Elbow
6' Max.
Offset
Elbow
Offset
Elbow
A
Return
Elbow
Offset
6' Max. Elbow
B
6' Max.
6' Max.
C
Figure 12 - Typical Offset Terminations
FIRESTOP SPACERS (FS-10, 1100EFS-10DM FOR 36" MODELS)
Firestop spacers are required at each point where the chimney penetrates
a floor space. Their purpose is to establish and maintain the required
clearance between the chimney and the combustible materials. When
the pipe passes through a framed opening into a living space above, the
firestop must be placed onto the ceiling from below as shown in Figure 13.
They also provide complete separation from one floor space to another
or attic space as required by most codes. When the double wall pipe
passes through a framed opening into an attic space, the firestop must
be placed into an attic floor as shown in Figure 14.
Existing
Ceiling
Frame
Firestop
Spacer
PENETRATING ROOF
To maintain a 1" (36" Models) or 2" (42/50" Models) clearance to the
pipe on a roof with a pitch, a rectangular opening must be cut.
1. Determine center point through which pipe will penetrate roof.
2. Determine center point of roof. Pitch is distance the roof drops
over a given span, usually 12". A 6/12 pitch means that roof drops
6" for each 12" measured horizontally down from roof rafters.
3. Use roof opening chart (Figure 15, page 11) to determine correct
opening length and flashing required.
4. Remove shingles around opening measured. Cut out this section.
5. Add next sections of pipe until end penetrates roof line. Check
to see that proper clearances are maintained. Extend chimney by
adding sections of double wall pipe until pipe is minimum of 30"
above highest point of roof cutout. Termination and chimney must
extend a minimum of 36" above highest point where it passes
through roof.
Screws or
Staples
(Min. of 8)
Figure 13 - Firestop Spacer with Living Space Above Ceiling
Firestop
Spacer
Screws or Staples
(Min. of 8)
Existing
Ceiling
Frame
Figure 14 - Firestop Spacer with Attic Space Above Ceiling
10
Superiorfireplaces.US.com
127008-01B
VENTING INSTALLATION Continued
17" Min.
30" Min.
1" Min.
1" Min.
Installing Flashing on a Metal Roof
When installing the flashing on a metal roof, it is required that putty
tape be used between the flashing and the roof. The flashing must be
secured to the roof using #8 x 3/4" screws and then sealed with roof
coating to prevent leakage through the screw holes. A roof coating
must also be applied around the perimeter of the flashing to provide
a proper seal.
1" Min.
Opening "A"
Pitch
Flat
0-6/12
6/1212/12
Slope Opening Used Flashing
"A" Max. Model No.
0°
17"
V6F-10DM
26.6°
19"
V6F-10DM
45.0°
24"
V12F-10DM
Roof Opening 36" Models
19.5" Min.
FLASHING INSTALLATION (V6F-10DM OR V12F-10DM)
Determine the flashing to be used with the roof opening chart. Slide
flashing over pipe until base is flat against roof. Replace as many
shingles as needed to cover exposed area and flashing base. Secure
in position by nailing through shingles (see Figure 16). DO NOT NAIL
THROUGH FLASHING CONE.
Storm Collar
Flashing
Cone
Nail Only
Outer
Perimeter
of Flashing
Overlap
Shingles Top
and Sides Only
30" Min.
2" Min.
2" Min.
Underlap Shingles
at Bottom
2" Min.
Figure 16 - Flashing Installation
Opening "A"
Pitch
Slope Opening Used Flashing
"A" Max.
Model No.
Flat
0°
19.5"
V6F-10DM
0-6/12 26.6°
22'
V6F-10DM
6/1245.0°
27"
V12F-10DM
12/12
Roof Opening 42" and 50" Models
Figure 15 - Roof Opening Measurements
Storm Collar Installation (SC2-1)
Place storm collar over pipe and slide down until it is snug against
the open edge of the flashing (see Figure 17). Apply waterproof caulk
around the perimeter of the collar to provide a proper seal.
Chimney
Pipe
Waterproof
Caulk
Storm
Collar
Flashing
Figure 17 - Storm Collar
127008-01B
Superiorfireplaces.US.com
11
VENTING INSTALLATION Continued
Terminations/Spark Arrestor
The fireplace system must be terminated with the listed round top or
chase terminations. In any case, refer to the installation instructions
supplied with the termination.
CAUTION: Do not seal openings on the rooftop
flashing. Follow the installation instructions provided
with the termination being used.
10 FOOT RULE
All flue gas outlet chimney terminations must extend a minimum of
3 feet in height above the highest point where it passes through the
roof and must be at least 2 feet above the highest point of the roof
that is within a horizontal distance of 10 feet (see Figure 20).
Level of
Flue Gas
Outlet
10'
10'
RLT-12D
Stainless
Inner Flue
Pipe
Level of
Flue Gas
Outlet
Secure
Termination
to Outer
Pipe with 3
Screws
2' Min.
2' Min.
Waterproof
Caulking
Storm
Collar
Flashing
Overlap
Shingles (Top
and Sides of
Flashing Base)
Underlap
Shingles
Figure 18 - Termination
3' Min.
3' Min.
Figure 20 - 10 Foot Rule
FINISHING FIREPLACE
Combustible materials, such as wallboard, gypsum board, sheet rock,
drywall, plywood, etc. may make direct contact with sides and top
around the fireplace face. It is important that combustible materials
do not overlap the face itself. Brick, glass, tile or other noncombustible
materials may overlap the front face provided they do not obstruct
essential openings like louvered slots or any other opening. When
overlapping with a noncombustible facing material, use only noncombustible mortar or adhesive.
CHASE INSTALLATIONS
Instructions for chase installations are included with the chase style
termination chosen. In a multiple chase installation, be sure to provide
adequate distance between terminations to prevent smoke spillage
from one termination to another. We suggest that terminations be
separated at least 24", center to center and stacked at a vertical height
difference of 18" (see Figure 19).
Note: If a decorative shroud is to be installed, contact the manufacturer
for specifications.
18"
Min.
Typ.
24" Min.
24" Min.
Figure 19 - Multiple Chase Installation
12
Superiorfireplaces.US.com
127008-01B
FIREBRICK WALL INSTALLATION
WARNING
Slot
Right Face
LIFTING HAZARD
SINGLE -PERSON LIFT COULD
CAUSE INJURY.
USE ASSISTANCE WHEN MOVING
OR LIFTING.
FIREBRICK WALL INSTALLATION
IMPORTANT: Installation of brick should be done
after the fireplace is placed in a permanent location.
Hearth
Figure 22 - Slots for Firebrick Walls
1. The fireplace is shipped with the hearth preinstalled. It is held in
place for shipping with 3 shipping brackets (Figure 21). Remove
these brackets before installing any of the other firebrick walls.
Retaining
Bracket
Right Wall
Leading
Brick
Figure 23 - Installing Side Walls
Shipping
Brackets
Retaining Bracket
Figure 21 - Removing Shipping Brackets
2. Install the left and right firebrick walls. There is a bracket with
2 tabs on the bottom of each firebrick wall. Angle the wall into
the fireplace opening and into the slots on the side of the hearth
(Figure 22), then tilt the top of the panel toward the firebox surround.
3. Secure the firebrick wall using 2 of the retainers provided. The
bracket will slip underneath the metal lip on the top of the wall
and screw into the inner dome of the fireplace (Figure 23).
4. Install the rear firebrick wall last. Place the wall face side down
on the hearth with the bottom of the wall toward the rear of the
firebox and the top toward the front of the fireplace. Tilt the wall
up toward the back of the firebox. Secure with 2 rear retaining
brackets provided (Figure 24).
127008-01B
Figure 24 - Installing Rear Wall
5. It is recommended that the joints between all firebrick walls be
grouted for a more finished look, see grouting instructions.
For more information and to watch a how to video go to IHP.US.com
and select Technical Support.
Superiorfireplaces.US.com
13
FIREBRICK WALL INSTALLATION Continued
GROUTING INSTRUCTIONS
Material provided:
Bag of cement
Bag of sand
Material required:
Piping bag
Joints striker
Heavy duty mixing bucket
Sponge or Wet Cloth
1. Moisten brick surface with damp sponge or spray bottle just prior
to application. When bricks are wet, any excess grout mixture on
bricks will easily wipe off.
2. In a heavy duty mixing bucket, add equal parts cement and sand.
Add enough water and mix together well using a power drill with
mixing wand attachment to a yogurt like consistency. Not adding
enough water can lead to grout falling out after burning.
3. The overall length of piping bag should be about 16". If the bag is
longer than 16", cut it down to size by removing end with larger
opening. This will make the bag easier to handle.
4. Put grout mixture into piping bag making sure the smaller opening
is downward and over a moist towel to avoid spilling. Place a wet
towel over the bucket making sure it is directly on the surface of
grout mixture. This will keep the mixture moist and it will not dry
out before use.
5. Grout all joints where two firebrick walls come together.
6. Using a trowel, remove excess grout mixture by moving trowel in
the direction of the joint. Grout mixture in the joint should now be
flush with brick surface. If not enough grout is applied into each
space, grout may fall out after burning.
7. Using a joint striker, smooth out grout line.
Allow 72 hours before operating fireplace.
INSTALLING SCREEN
1. Slide round end of screen rod into rings at top of screen. Attach one
push-on nut to end of rod before attaching last ring of screen.
2. Insert the round end screen rod into hole on the left and right side
of smoke shelf (Figure 25).
3. Mount flat end of screen rod with #10 x 5/8" to center of smoke
shelf.
4. Install other screen rod in same manner.
Rating Plate
Hole for Screen Rod
Leading
Bricks
Figure 25 - Installing Fireplace Screen
INSTALLING GRATE RETAINERS
1. Place the provided grate retainers on the hearth as shown in Figure
26. The back of the retainer will be flush with the rear firebrick wall.
Mark the center of the hole on the hearth with a marker.
2. Drill two holes in the hearth in the marked locations using a masonry
3/16" drill bit.
3. Secure grate retainer with masonry screws provided.
WARNING: Risk of fire! Replace grate with an INNOVATIVE HEARTH PRODUCTS grate only (see Parts,
page 20). This grate has been designed to keep the
operation of your fireplace safe and efficient.
Figure 26 - Installing Grate Retainers
14
Superiorfireplaces.US.com
127008-01B
OPTIONAL GAS LINE INSTALLATION
Gas line hook up should be done by your supplier or a qualified
service person.
Note: Before you proceed, make sure your gas supply is turned off.
Use only a 1/2" black iron pipe and appropriate fittings.
1. Remove knockout indentation on refractory or firebrick wall located above refractory hearth floor. Knockout indentation must be
firmly tapped with any solid object such as a 1/2" dowel until it is
released. Remove fragmented portions of refractory (see Figure
27).
2. Remove gas line cover plate located on either side of fireplace and
pull out insulation from gas line conduit sleeve. Save insulation for
reuse. Replace screws.
3. Run a 1/2" black iron gas line into fireplace through the rear at gas
line conduit sleeve (if using a raised platform, add height). Provide
sufficient gas line into fireplace chamber for fitting connection (see
Figure 28).
Note: Secure incoming gas line to wood framing to provide rigidity for
threaded end.
4. Repack insulation around gas line and into sleeve opening. Seal any
gaps between gas line and refractory knockout hole with refractory
cement or commercial furnace cement, Install the gas appliance or
cap-off gas line if desired.
CAUTION: All gas piping and connections must be
tested for leaks after the installation is completed.
After ensuring that the gas valve is on, apply soap and
water solution to all connections and joints. Bubbles
forming show a leak. Correct all leaks at once. DO NOT
USE AN OPEN FLAME FOR LEAK TESTING AND DO NOT
OPERATE ANY APPLIANCE IF A LEAK IS DETECTED.
LEAK TESTING SHOULD BE DONE BY A QUALIFIED
SERVICE PERSON.
WARNING: Do not operate an unvented gas log set in
this fireplace with the chimney removed.
Outside of
Fireplace
Gas Line
Conduit
Insulation
Remove
Knockout
Side
Firebrick
Finished
Side
Outside of
Fireplace
Incoming
1/2" Black
Iron Pipe
Gas Line
Conduit
Repack
Insulation
Seal
Opening
with
Refractory
Cement
Side
Firebrick
Finished
Side
Provide Enough
Threaded
End for Fitting
Connection
Figure 28 - Gas Line Installation
A gas line or gas log lighter may be installed for the purpose of installing
a vented or vent-free decorative gas appliance incorporating an automatic
shutoff device and complying with the Standard for Decorative Gas Appliances for Installation in Vented Fireplaces, ANSI Z21.60 or American
Gas Association draft requirements for Gas Fired Log Lighters for Wood
Burning Fireplaces, Draft NO. 4 dated August, 1993.
If you install a decorative gas appliance (vented gas log), the decorative gas appliance must comply with the Standard for Decorative
Gas Appliance for Installation in Solid Fuel Burning Fireplaces, ANS
Z21.60 or Z21.84 and shall also be installed in accordance with the
National Fuel Gas Code, ANSI 7223NFPA 54 latest edition.
If you wish to install an unvented (vent-free) gas log set, only unvented
gas log sets which have been found to comply with the standard for
unvented room heaters, ANSI Z21.11.2 are to be installed in this
fireplace.
WARNING: If the fireplace has been used for wood
burning, the firebox and chimney must be cleaned
of soot, creosote and ashes be a qualified chimney
cleaner. Creosote will ignite if heavily heated.
WARNING: When using a decorative vented gas log,
the damper must be removed or permanently locked in
the fully open position and the glass doors must be in
the fully open position.
1/2" Dowel
Gas
Conduit
Cover
Brick with
Access
Hole
Figure 27 - Gas Line Access
127008-01B
Superiorfireplaces.US.com
15
GLASS DOOR INSTALLATION
DOOR FRAME MODELS
INSTALLING GLASS DOORS
BDMO36E/G/C, BDMO42E/G/C AND BDMO50E/G/C
Installation
1. Remove screws from smoke shelf (see Figure 29).
2. Mount top door frame and secure with screws provided (see
Figure 29).
3. Place bottom door frame on top of ash lip at front of fireplace
(see Figure 30).
4. Secure bottom door frame to brick with two hex screws provided
as shown in Figure 30 using a 7/16" open end or adjustable
wrench.
Spring clips have been installed but some adjustments may be
needed. Install the doors using the following steps:
1. With bifold doors completely folded, insert bottom pivot pin into
pivot hole located near bottom corner of front face opening and
swing door to vertical position making sure top pins slide into
door track. Door is installed when top door pin snaps into spring
clip.
2. Repeat step 1 for remaining door.
If you find the doors do not close properly or do not appear level or
straight, proceed with section on door adjustment,
Top Door
Frame
Smoke
Shelf
Fold Door
and Slide
Top Pins
Into Track
Spring
Clip
Insert Pin
into Spring
Clip
Insert
Bottom
Pivot Pin
into Hole
Pivot
Hole
Figure 29 - Installing Top Door Frame
Figure 31 - Installing Bi-Fold Doors
Ash Lip
DOOR ADJUSTMENT
Remove doors and slightly loosen lower pivot clips and upper spring
clips. Replace doors and fully close them. Use 1/8" shims (any material) to level doors. Once proper setting is achieved, carefully open
doors enough so that you can access spring clips with a phillips
screwdriver. Tighten screws. See Figure 32.
Bottom
Door
Frame
Ash Lip
Hex
Screw
Figure 30 - Installing Bottom Door Frame
WARNING: Discontinue use of the appliance immediately if doors are damaged and contact a qualified installer for repair. Only doors certified with the
appliance shall be used.
WARNING: Do not slam or strike doors. Damage
can result in a hazardous condition.
16
Superiorfireplaces.US.com
Figure 32 - Adjusting Bi-Fold Doors
127008-01B
OPERATION AND MAINTENANCE GUIDELINES
GLASS DOORS
Glass doors are optional with the fireplace. When fireplace is in operation,
doors must be fully opened or fully closed position only or a fire hazard
may be created (see Figure 33).
A fireplace equipped with glass doors operates much differently than a
fireplace with an open front. A fireplace with glass doors has a limited
amount of air for combustion.
Excessive heat within the fireplace can result if too large a fire is built or
if combustion air gate is not completely open. The following tips should
be followed to assure that both the fireplace and glass door retain their
beauty and function properly. Both the flue damper and glass doors must
be fully opened before starting fire. This will provide sufficient combustion
air and maintain safe temperatures in firebox.
IMPORTANT: The glass must be allowed to warm slowly and evenly.
The tempered glass will withstand a gradual temperature rise to 550° F,
which is more than a normal fire will generate. Such materials as pitch/
wax laden logs, very dry mill end lumber and large amounts of paper or
cardboard boxes can create an excessively hot fire and should not be
burned in this fireplace. Always keep the fire well back from the doors
and never allow flames to contact the glass.
OUTSIDE AIR AND DAMPER HANDLE OPERATION
The damper handle, which opens and closes the damper blade, is
located in the upper front face of the fireplace. Pushing the handle
forward and up through the keyway slot will free damper blade to
automatically open. Pushing the handle forward and down will lock
damper blade closed (see Figure 34).
Damper
Weight
To Close
Damper
WARNING: Fireplaces equipped with glass doors
should be operated only with doors fully opened or
doors fully closed. Doors, if left partly open, may draw
gas and flame out of the fireplace opening creating
risks of both fire and smoke.
Cleaning Glass
Clean glass with any commercial glass cleaner or soap and water. Do
not use any abrasive material to clean glass. Do not clean glass with any
cool water if glass is still hot from the fire and smoke.
Damper
Weight
To Open
Damper
Figure 34 - Operating Damper Handle
Doors Fully Closed
Fireplace Front
Doors
Fully Opened
Fireplace Front
Figure 33 - Bi-Fold Glass Doors
127008-01B
Superiorfireplaces.US.com
17
TECHNICAL SERVICE
REPLACEMENT PARTS
Yo u m a y h a v e f u r t h e r q u e s t i o n s a b o u t i n s t a l lation, operation, or troubleshooting. If so, contact IHP at
1-800-655-2008.
When calling please have your model and serial numbers of your
fireplace ready.
You can also visit our web site at
Superiorfireplaces.US.com.
If this product is missing a part or has a broken component, please
do not return it to the store. Call IHP at 1-800-655-2008 to answer
questions and replace parts under warranty.
Note: Use only original replacement parts. This will protect your
warranty coverage for parts replaced under warranty.
When calling or writing, please have your model and serial numbers
of your fireplace ready.
Model and serial number information are in the fireplace's rating plate
located on the fireplace smoke shelf.
18
Superiorfireplaces.US.com
127008-01B
IMPORTANT INFORMATION
Canadian code CAN/ULC-S610-M87 and
other pertinent codes require stainless steel
chimney for the installation of this fireplace.
A Cold Air Climate Kit is also required in
Canada and is recommended for cooler
regions in the United Stated. Below, find a
list of approved stainless steel parts.
Chimney Parts List for Canada
Model No.
8" Hi-Temp
Woodburning Chimney
12-8HT
12" Section Double Wall Pipe
18-8HT
18" Section Double Wall Pipe
24-8HT
24" Section Double Wall Pipe
36-8HT
36" Section Double Wall Pipe
48-8HT
48" Section Double Wall Pipe
30E-8HT
30" Offset and Return
12S-8HT
Chimney Support
RT-8HT
Round Top w/ Mesh Screen
RTT-8HT*
Round Top w/ Slip Section
& Mesh
RLT-8HT
Round Top w/ Louvers
RLTT-8HT*
Round Top w/ Slip Section
& Louvers
ET-8HT*
Square Top
ETL-8HT*
Square Top w/ Slip Section
AP-8HT
Anchor Plate/Collar Assembly
(Masonry Fireplaces)
CAK-8
Cold Air Collar Kit
IMPORTANT NOTICE
A manufactured shroud which
has been approved by a national testing agency for use
with this fireplace may be used
if installed in accordance with
the instructions by its manufacturer. A locally fabricated
shroud may be used with IHP
Shroud Leg Spacer Kit (SLK) in
accordance with instructions
provided with the shroud.
IMPORTANT NOTICE
When penetrating a ceiling
into an attic, a firestop thimble
(38FST or FST30) is required
to avoid intrusion by insulation
and recommended to negotiate
a joist.
NOTICE: The firebox canopy (hood)
must not be modified or replaced with
a canopy that may be provided with
the unvented decorative room heater.
CAUTION: THE STRUCTURAL INTEGRITY OF
THE MANUFACTURED HOME FLOOR, WALL,
AND CEILING/ROOF MUST BE MAINTAINED.
WARNING: DO NOT INSTALL IN SLEEPING
ROOM OF MOBILE HOMES.
WARNING: Discontinue use of the
appliance immediately if doors
are damaged and contact a qualified installer for repair. Only doors
certified with the appliance shall
be used.
WARNING: Do not slam or strike
doors. Damage can result in a hazardous condition.
Thimble 38FST
or FST 30
*When ordered alone, this part cannot ship
via parcel delivery services.
Firestop
127008-01B
Superiorfireplaces.US.com
19
PARTS
MODELS 36", 42", AND 50" Catalog numbers are included for convenience.
10
MODEL
CATALOG NO.
WRE6036RS
WRE6036IS
WRE6036RH
WRE6036IH
WRE6042RS
WRE6042IS
WRE6042RH
WRE6042IH
WRE6050RS
WRE6050IS
WRE6050RH
WRE6050IH
F0409
F0410
F0411
F0412
F0413
F0414
F0415
F0416
F0417
F0418
F0419
F0420
8
7
6
9
5
11
12
20
21
14
4
13
22
16/17
15
1
2
19
24
23
3
18
25
20
Superiorfireplaces.US.com
127008-01B
PARTS
This list contains replaceable parts used in your firebox. When ordering parts, follow the instructions listed under Replacement Parts on
page 18 of this manual. Catalog numbers are included for convenience.
WARNING: Contact an IHP dealer to obtain any of these parts. Never use substitute materials not approved
by IHP. Use of non-approved parts can result in poor performance and safety hazards.
KEY NO.
1
2
3
4
5
6
7
8
9
WRE6042RS (F0413)
WRE6042IS (F0414)
WRE6042RH (F0415)
WRE6042IH (F0416)
DESCRIPTION
Face Assembly
•
Firebox Bottom Assembly
•
Firebox Bottom
•
Firebox Surround
•
Outer Dome Assembly
•
Insulation Pan Support
•
Insulation Pan
•
Top Insulation
•
Fireplace Top Assembly, 36"
•
Fireplace Top Assembly, 42"
Fireplace Top Assembly, 50"
10
Standoff
•
11
Fireplace Surround Assembly
•
12
Clearance Spacer
•
13
Fireplace Handle Bracket
•
14
Outside Air Cover Plate
•
15
Gas Conduit Cover
•
16
Conduit One
•
17
Conduit Two
•
18
Heat Shield Support
•
19
Ash Box Assembly
•
20
Inner Dome Assembly
•
21
Smoke Shield
•
22
Damper Control Bracket
•
23
Screen 36" Stainless
•
Screen 42" Stainless
Screen 50" Stainless
24
Screen Rod 36" Stainless
•
Screen Rod 42" Stainless
Screen Rod 50" Stainless
25
Grate 36" Stainless
•
Grate 42" Stainless
Grate 50" Stainless
PARTS AVAILABLE NOT SHOWN
124174-02
Grate Retainer Stainless
•
109714-02
Side Firebrick Wall Spacers
•
114913-01
Rear Firebrick Wall Spacers
•
** Not a field replaceable part.
127008-01B
PART NO.
**
**
**
**
**
**
**
**
110285-03
110285-02
110285-01
23490SA
**
109720-02
117891-01
20042
21171
109752-01
109752-02
**
123298-02
**
**
**
117566-03
117566-01
117566-02
117568-03
117568-01
117568-02
117544-03
117544-01
117544-02
WRE6036RS (F0409)
WRE6036IS (F0410)
WRE6036RH (F0411)
WRE6036IH (F0412)
Superiorfireplaces.US.com
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
WRE6050RS (F0417)
WRE6050IS (F0418)
WRE6050RH (F0419)
WRE6050IH (F0420)
•
QTY.
1
1
1
1
1
1
1
1
1
1
1
4
1
6
4
2
4
2
2
1
1
1
1
1
2
2
2
2
2
2
1
1
1
•
•
•
2
4
2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
21
PARTS
MODELS 36", 42" AND 50" Picture may vary from actual
7
7
8
6
8
1
4
7
7
5
9
3
2
Note: See pages 23 and 24 for part numbers.
WARNING
LIFTING HAZARD
SINGLE -PERSON LIFT COULD
CAUSE INJURY.
USE ASSISTANCE WHEN MOVING
OR LIFTING.
22
IMPORTANT: Installation of brick panels should be
done after the fireplace is placed in a permanent
location.
Superiorfireplaces.US.com
127008-01B
PARTS
KEY NO. PART NO.
1
125116-01
125118-01
2
125116-02
125118-02
3
125036-01
125037-01
125038-01
4
124210-01
124222-01
125413-01
125425-01
125437-01
125449-01
5
124212-01
124224-01
125415-01
125427-01
125439-01
125451-01
6
124214-01
124226-01
125417-01
125429-01
125441-01
125453-01
7
124134-04
124134-05
8
124134-06
9
120848-01
127008-01B
DESCRIPTION
Left Leading Brick 36" Red
Left Leading Brick 42"/50" Red
Right Leading Brick 36" Red
Right Leading Brick 42"/50" Red
Hearth 36" Red
Hearth 42" Red
Hearth 50" Red
Rear Stacked 36" Red
Rear Herringbone 36" Red
Rear Stacked 42" Red
Rear Herringbone 42" Red
Rear Stacked 50" Red
Rear Herringbone 50" Red
Right Stacked 36" Red
Right Herringbone 36" Red
Right Stacked 42" Red
Right Herringbone 42" Red
Right Stacked 50" Red
Right Herringbone 50" Red
Left Stacked 36" Red
Left Herringbone 36" Red
Left Stacked 42" Red
Left Herringbone 42" Red
Left Stacked 50" Red
Left Herringbone 50" Red
Side Retainer 36" Stainless
Side Retainer 42"/50" Stainless
Rear Retainer Stainless
Ash Brick Red
Superiorfireplaces.US.com
WRE
60
WRE 36RS
6036
RH
WRE
6042
RS
WRE
604
WRE 2RH
60
WRE 50RS
6050
RH
This list contains replaceable parts used in your firebox. When ordering parts, follow the instructions listed under Replacement Parts on
page 18 of this manual.
• •
• •
• •
•
•
•
•
•
•
• •
• • • •
• • • •
• •
•
•
•
•
•
•
• •
•
•
•
•
•
•
• • • •
• • • • • •
• • • • • •
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
4
2
1
23
PARTS
KEY NO. PART NO.
1
125116-03
125118-03
2
125116-04
125118-04
3
125036-02
125037-02
125038-02
4
124210-02
124222-02
125413-02
125425-02
125437-02
125449-02
5
124212-02
124224-02
125415-02
125427-02
125439-02
125451-02
6
124214-02
124226-02
125417-02
125429-02
125441-02
125453-02
7
124134-04
124134-05
8
124134-06
9
120848-03
24
DESCRIPTION
Left Leading Brick 36" Ivory
Left Leading Brick 42"/50" Ivory
Right Leading Brick 36" Ivory
Right Leading Brick 42"/50" Ivory
Hearth 36" Ivory
Hearth 42" Ivory
Hearth 50" Ivory
Rear Stacked 36" Ivory
Rear Herringbone 36" Ivory
Rear Stacked 42" Ivory
Rear Herringbone 42" Ivory
Rear Stacked 50" Ivory
Rear Herringbone 50" Ivory
Right Stacked 36" Ivory
Right Herringbone 36" Ivory
Right Stacked 42" Ivory
Right Herringbone 42" Ivory
Right Stacked 50" Ivory
Right Herringbone 50" Ivory
Left Stacked 36" Ivory
Left Herringbone 36" Ivory
Left Stacked 42" Ivory
Left Herringbone 42" Ivory
Left Stacked 50" Ivory
Left Herringbone 50" Ivory
Side Retainer 36" Stainless
Side Retainer 42"/50" Stainless
Rear Retainer Stainless
Ash Brick Ivory
Superiorfireplaces.US.com
WRE
60
WRE 36IS
6036
IH
WRE
6042
IS
WRE
6042
I
H
WRE
6050
I
S
WRE
6050
IH
This list contains replaceable parts used in your firebox. When ordering parts, follow the instructions listed under Replacement Parts on
page 18 of this manual.
• •
• •
• •
•
•
•
•
•
•
• •
• • • •
• • • •
• •
•
•
•
•
•
•
• •
•
•
•
•
•
•
• • • •
• • • • • •
• • • • • •
QTY.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
4
2
1
127008-01B
ACCESSORIES
EMBER PROTECTOR 20093
BI-FOLD GLASS DOORS
BI-FOLD GLASS DOORS
MODEL
BDMO36E
BDMO36G
BDMO36C
BDMO42E
BDMO42G
BDMO42C
BDMO50E
BDMO50G
BDMO50C
DESCRIPTION
GLASS DOOR, 36" EBONY
GLASS DOOR, 36" PEWTER
GLASS DOOR, 36" OILED BRONZE
GLASS DOOR, 42" EBONY
GLASS DOOR, 42" PEWTER
GLASS DOOR, 42" OILED BRONZE
GLASS DOOR, 50" EBONY
GLASS DOOR, 50" PEWTER
GLASS DOOR, 50" OILED BRONZE
OPTIONAL OUTSIDE AIR KIT FOR FLOOR INSTALLATION - AK4F
DOUBLE WALL PIPE 12-12DM, 18-12DM, 24-12DM, 36-12DM, 48-12DM, 12-12HT,
18-12HT, 24-12HT, 36-12HT and 48-12HT
OPTIONAL OUTSIDE AIR KIT FOR SIDEWALL INSTALLATION AK4
30° OFFSET AND RETURN
30E-12DM and 30E-12HT
STORM COLLAR - SC2-1
127008-01B
Superiorfireplaces.US.com
25
ACCESSORIES Continued
FIRESTOP SPACER - FS-10 AND 1100EFS-10DM
SQUARE CHASE-TOP TERMINATION - STL-12D AND
STL-12DMP BLACK
ROOF FLASHING
V6F-10DM - 0 to 6/12 Pitch
V12F-10DM - 6/12 to 12/12 Pitch
ROUND TOP TERMINATIONS
RLT-12D AND RLT-12HT
26
Superiorfireplaces.US.com
127008-01B
Innovative Hearth Products
Superior™ Brand Wood-Burning Fireplace
20 Year Limited Warranty
THE WARRANTY
Innovative Hearth Products ("IHP") 20 Year Limited Warranty warrants your Superior™ Brand wood burning fireplace ("Product") to be free from defects in materials and
workmanship at the time of manufacture. The Product body, firebox and ceramic glass carry the 20 Year Limited Warranty. Ceramic glass carries the 20 Year Limited Warranty
against thermal breakage only. After installation, if covered components manufactured by IHP are found to be defective in materials or workmanship during the 20 Year Limited
Warranty period and while the Product remains at the site of the original installation, IHP will, at its option, repair or replace the covered components. If repair or replacement
is not commercially practical, IHP will, at its option, refund the purchase price or wholesale price of the IHP product, whichever is applicable. IHP will also pay IHP prevailing
labor rates, as determined in its sole discretion, incurred in repairing or replacing such components for up to five years. THERE ARE EXCLUSIONS AND LIMITATIONS to this
20 Year Limited Warranty as described herein.
COVERAGE COMMENCEMENT DATE
Warranty coverage begins on the date of installation. In the case of new home construction, warranty coverage begins on the date of first occupancy of the dwelling or six
months after the sale of the Product by an independent IHP dealer/distributor, whichever occurs earlier. The warranty shall commence no later than 24 months following the
date of product shipment from IHP, regardless of the installation or occupancy date.
EXCLUSIONS AND LIMITATIONS
This 20 Year Limited Warranty applies only if the Product is installed in the United States or Canada and only if operated and maintained in accordance with the printed instructions accompanying the Product and in compliance with all applicable installation and building codes and good trade practices.
This warranty is non-transferable and extends to the original owner only. The Product must be purchased through a listed supplier of IHP and proof of purchase must be
provided. The Product body and firebox carry the 20 Year Limited Warranty from the date of installation. Vent components, trim components, paint and applied stains are
excluded from this 20 Year Limited Warranty. The following do not carry a 20 Year Limited Warranty but are warranted as follows:
Air tubes, baffles and brick retainers – Repair or replacement for one year from the date of installation
Cast iron parts – Replacement for one year from date of installation
Catalyst – Carries a separate warranty. Refer to the warranty certificate provided for that part
Electrical components – Repair or replacement for one year from the date of installation
Fireplace screens, refractory and side shields (metal or refractory) – Repair or replacement for two years from date of installation. Excludes hairline cracks.
Fuel grates –These parts are considered consumable accessories and therefore are not warranted, with the exception of defects in material or workmanship which
are covered for 90 days from the date of installation
Gaskets – Replacement for one year from date of installation
Gold & nickel plating – Replacement for two years from date of installation. Excludes tarnishing
Optional glass doors – Repair or replacement for 90 days from the date of installation
Refractory & screens – Replacement for two years from date of installation. Excludes hairline cracks
Removable air tubes – Repair or replacement for seven years from date of installation. IHP prevailing labor rates for years one through five.
Labor coverage – Prevailing IHP labor rates apply for the warranty period of the component.
Parts not otherwise listed carry a 90 day warranty from the date of installation.
Whenever practicable, IHP will provide replacement parts, if available, for a period of 10 years from the last date of manufacture of the Product.
IHP will not be responsible for: (a) damages caused by normal wear and tear, accident, riot, fire, flood or acts of God; (b) damages caused by abuse, negligence, misuse, or
unauthorized alteration or repair of the Product affecting its stability or performance. (The Product must be subject to normal use with approved fuels listed in the Operation
Manual provided with the product. This includes burning such fireplace fuels as wood and natural or propane gas. Fuel products with abnormal burning characteristics,
including but not limited to fuel such as driftwood, coal or plywood and wood products using a binder may burn at excessive temperatures and may cause damage to the
Product or may cause it to function improperly.); (c) damages caused by failing to provide proper maintenance and service in accordance with the instructions provided with
the Product; (d) damages, repairs or inefficiency resulting from faulty installation or application of the Product.
Coverage of this 20 Year Limited Warranty is conditional upon use of an adequate fuel grate on factory-built fireplaces only, when applicable.
IHP is not responsible for inadequate fireplace system draft caused by air conditioning and heating systems, mechanical ventilation systems, or general construction conditions which may generate negative air pressure in the room in which the appliance is installed. Additionally IHP assumes no responsibility for smoking conditions caused by
inadequate chimney height, adjoining trees or buildings, adverse wind conditions or unusual environmental factors and conditions. Certain IHP Products are listed for use with
Security Chimneys International, Ltd. or IHP chimney systems only. Use of chimney components other than that specified in the Product manual will void the Product warranty.
This 20 Year Limited Warranty covers only parts and labor as provided herein. In no case shall IHP be responsible for materials, components or construction which are not
manufactured or supplied by IHP or for the labor necessary to install, repair or remove such materials, components or construction. Additional utility bills incurred due to any
malfunction or defect in equipment are not covered by this 20 Year Limited Warranty. All replacement or repair components will be shipped F.O.B. from the nearest stocking
IHP factory.
LIMITATION ON LIABILITY
It is expressly agreed and understood that IHP’s sole obligation and the purchaser’s exclusive remedy under this warranty, under any other warranty, expressed or implied, or
in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified herein.
In no event shall IHP be liable for any incidental or consequential damages caused by defects in the Product, whether such damage occurs or is discovered before or after
replacement or repair, and whether such damage is caused by IHP’s negligence. IHP has not made and does not make any representation or warranty of fitness for a particular
use or purpose, and there is no implied condition of fitness for a particular use or purpose.
IHP makes no expressed warranties except as stated in this 20 Year Limited Warranty. The duration of any implied warranty is limited to the duration of this expressed warranty.
No one is authorized to change this 20 Year Limited Warranty or to create for IHP any other obligation or liability in connection with the Product. Some states and provinces
do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. The provisions of this 20 Year
Limited Warranty are in addition to and not a modification of or subtraction from any statutory warranties and other rights and remedies provided by law.
INVESTIGATION OF CLAIMS AGAINST WARRANTY
IHP reserves the right to investigate any and all claims against this 20 Year Limited Warranty and to decide, in its sole discretion, upon the method of settlement.
To receive the benefits and advantages described in this 20 Year Limited Warranty, the appliance must be installed and repaired by a licensed contractor approved by IHP.
Contact IHP at the address provided herein to obtain a listing of approved dealers/distributors. IHP shall in no event be responsible for any warranty work done by a contractor that is not approved without first obtaining IHP's prior written consent.
HOW TO REGISTER A CLAIM AGAINST WARRANTY
In order for any claim under this warranty to be valid, you must contact the IHP dealer/distributor from which you purchased the product. If you cannot locate the dealer/
distributor, then you must notify IHP in writing. IHP must be notified of the claimed defect in writing within 90 days of the date of failure. Notices should be directed to the IHP
Warranty Department at 1508 Elm Hill Pike, Suite 108; Nashville, TN 37210 or visit our website at WWW.SUPERIORFIREPLACES.US.COM.
Printed in U.S.A. © 2013 Innovative Hearth Products LLC
127008-01B
P/N
900224-00, Rev. NC 12/2013
Superiorfireplaces.US.com
Innovative Hearth Products
27
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
WARRANTY
KEEP THIS WARRANTY
Model (located on product or id tag) Burner System__________Cast Stove____________
Serial No. (located on product or identification tag)____________________
Date Purchased _______________________
Keep receipt for warranty verification.
IHP reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products. Consult your local distributor
for fireplace code information.
P127008-01
Printed in U.S.A. © 2014 IHP LLC
P/N 127008-01 Rev. B 10/2014.
1508 Elm Hill Pike, Suite 108
Nashville, TN 37210
1-800-655-2008
IHP.US.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement