INST99-7001_web

INST99-7001_web
INSTALLATION INSTRUCTIONS FOR PART 99-7001
APPLICATIONS
See application list inside
KIT FEATURES
• Single DIN radio provision
• Equalizer provision
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness:
• 70-1743
• 70-7001
• 70-7003
Antenna Adapter:
• Not required
KIT COMPONENTS
• A) Radio housing • B) Bracket set #1 • C) Bracket set #2 • D) Bracket set #3 • E) Faceplate
• F) (2) #6 x 3/4” Phillips flat-head screws • G) Filler bar • H) Equalizer dummy plate
TOOLS REQUIRED
• Phillips screwdriver • Cutting tool
• Socket wrench
Dodge/Eagle/Mitsubishi/Plymouth 1990-2005
99-7001
REV. 8/13/2014 INST99-7001
A
B
E
C
F
D
G
H
CAUTION: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
NOTE: Refer to the instructions included with the
aftermarket radio.
METRA. The World’s best kits.™
1-800-221-0932
metraonline.com
© COPYRIGHT 2004-2014 METRA ELECTRONICS CORPORATION
99-7001
Applications
Table of Contents
DODGE
MITSUBISHI (continued)
Dash Disassembly
Colt....................................... 1993-1995
Mirage.................................. 1993-1996
– Dodge Colt/Eagle Summit 1993-1995, Mitsubishi Mirage 1993-1996..................3
Stealth.................................. 1991-1996
Mirage.................................. 1997-2002
– Dodge Stealth 1991-1996, Mitsubishi 3000GT 1991-1998...................................4
Montero................................ 1992-1996
– Eagle Summit (wagon) 1992-1996, Mitsubishi Expo 1992-1995,
Montero Sport....................... 2000-2004
Plymouth Colt Vista 1992-1994............................................................................5
Summit (wagon).................... 1992-1996
PLYMOUTH
– Eagle Talon/Mitsubishi Eclipse/Plymouth Laser 1990-1994..................................6
Talon.................................... 1990-1994
Colt Vista.............................. 1992-1994
– Eagle Talon 1995-1998, Mitsubishi Eclipse 1995-1999........................................7
Talon.................................... 1995-1998
Laser ................................... 1990-1994
– Mitsubishi Diamante 1994-1996..........................................................................8
EAGLE
Summit................................. 1993-1995
– Mitsubishi Eclipse 2000-2005..............................................................................9
MITSUBISHI
– Mitsubishi Galant 1994-1998.............................................................................10
3000GT................................ 1991-1998
– Mitsubishi Mirage 1997-2002............................................................................11
Diamante.............................. 1994-1996
– Mitsubishi Montero 1992-1996..........................................................................12
Eclipse.................................. 1990-1994
– Mitsubishi Montero Sport 2000-2004................................................................13
Eclipse.................................. 1995-1999
Eclipse.................................. 2000-2005
Kit Assembly.................................................................................................. 14-17
Expo..................................... 1992-1995
– Single DIN radio provision..................................................................................15
Galant................................... 1994-1998
– Equalizer provision.............................................................................................15
2
Dash Disassembly 99-7001
Dodge Colt/Eagle Summit 1993-1995, Mitsubishi Mirage 1993-1996
1. Remove (2) Phillips
screws below the A/C
vents. Pry out on the top
of the dash trim bezel
and remove the bezel.
(Figure A)
2. Remove (4) screws
securing the factory
radio and disconnect the wiring.
(1)
3. Cut and remove
mounting tabs “A” and
“B” on the radio housing.
C
(4)
(Figure C)
Dash trim bezels with a divided radio opening:
• If NOT keeping the factory pocket: Cut and remove the upper rib from the radio opening
and snap the filler bar onto the bottom of the radio housing. (Figure C, 1)
• If keeping the factory pocket: Cut and remove the upper rib from the radio opening and
the bottom portion of the radio housing. (Figure C, 2)
4. Cut and remove all
mounting tabs on
bracket set #1 EXCEPT
tabs “C”. (Figure B)
(2)
(Figure A)
(3)
Note: Mounting tabs are identified by the
letter stamped on backs
of each tab.
C
Dash trim bezels with an undivided radio opening:
• If NOT keeping the factory pocket: Cut and remove the lower rib from the radio opening
and the top portion of the radio housing. (Figure C, 3)
• If keeping the factory pocket: Cut and remove the lower rib from the radio opening, the
top portion of the radio housing and the bottom portion of the housing. (Figured C, 4)
Continue to kit assembly
(Figure B)
3
Dash Disassembly 99-7001
Dodge Stealth 1991-1996, Mitsubishi 3000GT 1991-1998
1. Using a panel removal
tool, pry out on the radio
trim bezel and remove.
(Figure A)
(1)
(2)
(3)
2. Remove (4) screws
securing the factory
radio and disconnect the wiring.
3. Cut and remove
mounting tabs “A” and
“B” on the radio housing.
(Figure A)
E
4. Cut and remove all
mounting tabs on
bracket set #2 EXCEPT
tabs “E”. (Figure B)
(Figure C)
Dash trim bezels with a divided radio opening:
• If NOT keeping the factory pocket: Cut and remove the upper rib from the radio opening
and snap the filler bar onto the bottom of the radio housing. (Figure C, 1)
• If keeping the factory pocket: Cut and remove the upper rib from the radio opening and
the bottom portion of the radio housing. (Figure C, 2)
Note: Mounting tabs are identified by the
letter stamped on backs
of each tab.
E
Dash trim bezels with an undivided radio opening:
• Cut and remove the lower rib from the radio opening and the top portion of the radio
housing. (Figure C, 3)
Continue to kit assembly
(Figure B)
4
Dash Disassembly 99-7001
Eagle Summit (wagon) 1992-1996, Mitsubishi Expo 1992-1995,
Plymouth Colt Vista 1992-1994
1. Remove (2) screws from
the top edge of the dash
trim bezel. Remove the
ashtray and (2) screws
exposed. Unclip the
dash trim bezel and
disconnect the cigarette
lighter wiring.
2. Remove (4) Phillips
screws securing the
factory radio and
disconnect the wiring.
(1)
(2)
(Figure A)
F
3. Cut and remove
mounting tabs “A” and
“B” on the radio housing.
(4)
(Figure C)
Dash trim bezels with a divided radio opening:
• If NOT keeping the factory pocket: Cut and remove the upper rib from the radio opening
and snap the filler bar onto the bottom of the radio housing. (Figure C, 1)
• If keeping the factory pocket: Cut and remove the upper rib from the radio opening and
the bottom portion of the radio housing. (Figure C, 2)
4. Cut and remove all
mounting tabs on
bracket set #2 EXCEPT
tabs “F”.
(3)
Note: Mounting tabs are identified by the
letter stamped on backs
of each tab.
F
(Figure B)
Dash trim bezels with an undivided radio opening:
• If NOT keeping the factory pocket: Cut and remove the lower rib from the radio opening
and the top portion of the radio housing. (Figure C, 3)
• If keeping the factory pocket: Cut and remove the lower rib from the radio opening, the
top portion of the radio housing and the bottom portion of the housing. (Figured C, 4)
Continue to kit assembly
5
Dash Disassembly 99-7001
Eagle Talon/Mitsubishi Eclipse/Plymouth Laser 1990-1994
1. Unclip the radio trim
bezel (the factory pocket
will be attached).
(1)
(2)
(3)
2. Remove (4) screws
securing the factory
radio and disconnect the wiring.
3. Cut and remove all
mounting tabs on the
radio housing EXCEPT
tabs “B”. (Figure B)
(Figure A)
B
Note: Mounting tabs are identified by the
letter stamped on backs
of each tab.
(Figure C)
Dash trim bezels with a divided radio opening:
• If NOT keeping the factory pocket: Cut and remove the upper rib from the radio opening
and snap the filler bar onto the bottom of the radio housing. (Figure C, 1)
• If keeping the factory pocket: Cut and remove the upper rib from the radio opening and
the bottom portion of the radio housing. (Figure C, 2)
B
Dash trim bezels with an undivided radio opening:
• Cut and remove the lower rib from the radio opening and the top portion of the radio
housing. (Figure C, 3)
Continue to kit assembly
(Figure B)
6
Dash Disassembly 99-7001
Eagle Talon 1995-1998, Mitsubishi Eclipse 1995-1999
1. Slide the front seats
forward and remove (1)
cover cap and (1) Phillips
screw from each side of
the center console.
Center console
2. Unsnap the cupholder/
ashtray assembly and
remove (2) Phillips
screws exposed.
3. Unclip the radio trim
bezel and remove (2)
Phillips screws exposed.
(Figure A)
Radio trim bezel
(Figure A)
Keep “G” tabs
B
(Figure C)
4. Unscrew the shifter
knob. Disconnect the
cigarette lighter and light wiring. Lift up on
the center console and remove.
5. Remove (4) Phillips
screws securing the
factory radio and
disconnect the wiring.
Remove
shaded portions
Cut and remove
6. Cut and remove mounting tabs “A” and “B” on the radio housing. Cut and remove the
lower rib from the radio opening. (Figure B)
A
B
7. Cut and remove all mounting tabs on backet set #2 EXCEPT tabs “G”. (Figure C)
Note: Mounting tabs are identified by the letter stamped on backs of each tab.
8. Once the mounting tabs are removed, cut and remove the SHADED portions of the
brackets. (Figure C)
Continue to kit assembly
(Figure B)
7
Dash Disassembly 99-7001
Mitsubishi Diamante 1994-1996
1. Remove (2) Phillips screws from each side of the gear shifter console.
4. Remove (4) screws securing the factory radio and disconnect
the wiring.
2. Remove (2) Phillips screws from the top of the console (under
the ashtray).
5. Cut and remove all mounting tabs
on the radio housing EXCEPT tabs
“A”. Cut and remove the lower rib
from the radio opening. (Figure B)
3. Lift the console out and remove
(2) Phillips screws exposed at the
base of the dash trim bezel. Pull
out on the bottom of the dash trim
bezel, disconnect the wiring and
remove the bezel. (Figure A)
Cut and remove
shaded areas
Note: Mounting tabs are identified
by the letter stamped on backs of
each tab.
Keep “A” tabs
(Figure C)
Cut and remove
6. Cut and remove all mounting tabs on
bracket set #1 EXCEPT tabs “A”. (Figure C)
Note: Mounting tabs are identified by
the letter stamped on backs of each tab.
7. Once the mounting tabs are removed,
cut the SHADED portions from the
brackets. (Figure C)
Continue to kit assembly
Keep “A” tabs
(Figure A)
(Figure B)
8
Dash Disassembly 99-7001
Mitsubishi Eclipse 2000-2005
1. Remove (2) Phillips screws under the climate
controls. Unclip the radio/climate control trim
bezel and remove the bezel. (Figure A)
2. Remove (4) Phillips screws securing the factory
radio and disconnect the wiring.
3. Cut and remove mounting tabs “A” and “B” on the
radio housing. (Figure C)
4. Locate mounting tabs “A” on bracket set #3.
(Figure B)
Note: Mounting tabs are identified by the letter
stamped on backs of each tab.
5. Cut and remove the lower rib from the radio
opening and the top portion of the radio housing.
(Figure C)
Continue to kit assembly
Locate mounting
tabs “A”
B
Cut and remove
A
B
(Figure A)
(Figure B)
(Figure C)
9
Dash Disassembly 99-7001
Mitsubishi Galant 1994-1998
1. Unclip the gear shifter trim panel and remove.
Remove (2) Phillips screws exposed at the base of
the dash trim bezel. (Figure A)
2. Unclip the dash trim bezel. Remove (4) Phillips
screws securing the factory radio and disconnect
the wiring.
3. Cut and remove mounting tabs “A” and “B” on the
radio housing. (Figure C)
4. Cut and remove all mounting tabs on bracket set
#1 EXCEPT tabs “D”. (Figure B)
5. Cut and remove the lower rib from the radio
opening. (Figure C)
Note: Mounting tabs are identified by the letter
stamped on backs of each tab.
Continue to kit assembly
Keep all “D” tabs
B
Cut and remove
A
B
Keep all “D” tabs
(Figure A)
(Figure B)
(Figure C)
10
Dash Disassembly 99-7001
Mitsubishi Mirage 1997-2002
1. Pry out on the top of
the dash trim bezel
and remove the bezel.
(Figure A)
(1)
(3)
2. Remove (4) screws
securing the factory
radio and disconnect the wiring.
3. Cut and remove
mounting tabs “A” and
“B” on the radio housing.
C
(4)
(Figure C)
Dash trim bezels with a divided radio opening:
• If NOT keeping the factory pocket: Cut and remove the upper rib from the radio opening
and snap the filler bar onto the bottom of the radio housing. (Figure C, 1)
• If keeping the factory pocket: Cut and remove the upper rib from the radio opening and
the bottom portion of the radio housing. (Figure C, 2)
4. Locate mounting tabs
“C” on bracket set #1.
(Figure B)
(2)
(Figure A)
Note: Mounting tabs are identified by the
letter stamped on backs
of each tab.
C
Dash trim bezels with an undivided radio opening:
• If NOT keeping the factory pocket: Cut and remove the lower rib from the radio opening
and the top portion of the radio housing. (Figure C, 3)
• If keeping the factory pocket: Cut and remove the lower rib from the radio opening, the
top portion of the radio housing and the bottom portion of the housing. (Figured C, 4)
Continue to kit assembly
(Figure B)
11
Dash Disassembly 99-7001
Mitsubishi Montero 1992-1996
1. Remove (2) screws
above the climate
controls. Unclip the
bottom of the dash trim
bezel and remove the
bezel. (Figure A)
2. Remove (4) screws
securing the factory
radio and disconnect the wiring.
(1)
3. Cut and remove
mounting tabs “A” and
“B” on the radio housing.
B
(4)
(Figure C)
Dash trim bezels with a divided radio opening:
• If NOT keeping the factory pocket: Cut and remove the upper rib from the radio opening
and snap the filler bar onto the bottom of the radio housing. (Figure C, 1)
• If keeping the factory pocket: Cut and remove the upper rib from the radio opening and
the bottom portion of the radio housing. (Figure C, 2)
4. Cut and remove all
mounting tabs on
bracket set #1 EXCEPT
tabs “B”. (Figure B)
(2)
(Figure A)
(3)
Dash trim bezels with an undivided radio opening:
• If NOT keeping the factory pocket: Cut and remove the lower rib from the radio opening
and the top portion of the radio housing. (Figure C, 3)
• If keeping the factory pocket: Cut and remove the lower rib from the radio opening, the
top portion of the radio housing and the bottom portion of the housing. (Figured C, 4)
Note: Mounting tabs are identified by the
letter stamped on backs
of each tab.
B
Continue to kit assembly
(Figure B)
12
Dash Disassembly 99-7001
Mitsubishi Montero Sport 2000-2004
1. Unclip the radio/climate control trim bezel and
remove the bezel.
2. Remove (4) Phillips screws securing the factory
radio and disconnect the wiring.
3. Cut and remove mounting tabs “A” and “B” on the
radio housing.
4. Locate mounting tabs “B” on bracket set #3 and
cut and remove the mounting legs containing tabs
“A” by cutting along scored lines “X”.
Note: Mounting tabs are identified by the letter
stamped on backs of each tab.
5. Cut and remove the lower rib from the radio
opening and the top portion of the radio housing.
(Figure C)
Continue to kit assembly
Cut along the “X”
score lines
(Figure A)
(Figure B)
(Figure C)
13
Kit Assembly 99-7001
All Vehicles
If the lower portion of the radio housing has been removed for pocket retention:
• Mount the brackets to the radio housing with (2) clips and (2) #6
x 1/4” Phillips flat-head screws supplied. (Figure A, 1)
(1)
(3)
(2)
(4)
If the lower portion of the radio housing has not been removed (excluding Diamante and Galant):
• Mount the brackets to the radio housing with (4) clips and (2) #6
x 1/4” Phillips flat-head screws supplied. (Figure A, 2)
Mitsubishi Diamante:
• Mount the brackets to the radio housing with (2) clips and (2) #6
x 1/4” Phillips flat-head screws supplied. (Figure A, 3)
Mitsubishi Galant:
• Mount the brackets to the radio housing with (4) clips and (2) #6
x 1/4” Phillips screws supplied. Slide the factory cupholder onto
the mounted brackets until the locater pins engage and mount
with (2) screws previously removed. (Figure A, 4)
Continue onto the next page
(Figure A)
14
99-7001
Kit Assembly
Single DIN radio provision:
• For dash trim bezels with an undivided radio opening:
Slide the DIN cage into the radio housing and secure by bending
the metal locking tabs down. Slide the aftermarket radio into
the cage until secure. With the side notches down, snap the
faceplate onto the front of the housing. (Figure A, 1)
• For dash trim bezels with a divided radio opening:
Slide the DIN cage into the radio housing and secure by bending
the metal locking tabs down. Slide the aftermarket radio into the
cage until secure. With the side notches up, snap the faceplate
onto the front of the housing. (Figure A, 2)
(1)
(2)
Notch down
Notch up
(Figure A)
Equalizer provision
• If an equalizer will be included:
Slide the aftermarket equalizer into the back of the radio housing.
Using the hardware included with the equalizer, mount the radio
to the kit. (Figure B, 1)
(1)
• If an equalizer will NOT be included:
Snap the equalizer dummy plate onto the radio housing. (Figure B, 2)
Continue onto the next page
(Figure B)
15
(2)
99-7001
Kit Assembly
Talon 1995-1998, Eclipse 1995-1999, Colt, Summit, Mirage,
Stealth, 3000GT, Diamante, Galant, Montero:
• No cutting of the dash or dash trim bezel is required.
(1)
Continue onto the next page
Talon, Eclipse, Laser 1990-1994:
• If keeping the factory pocket is desired, cut and remove the
inside half of each pocket mount located on the back of the dash
trim bezel. (Figure C, 1)
(2)
1/4”
Continue onto the next page
Summit (wagon), Expo, Colt Vista:
• Cut and remove 1/4” from the top edge of the dash cavity
opening. (Figure C, 2)
(3)
• If keeping the factory pocket is desired, cut and remove the
pocket mounts located on the back of the dash trim bezel.
(Figure C, 3)
Continue onto the next page
(Figure C)
16
99-7001
Kit Assembly
Notes
• Locate the factory wiring harness in the dash. Metra
recommends using the proper mating adapter from Metra or
AXXESS.
• Re-connect the negative battery terminal and test the radio for
proper operation.
• Reassemble dash in reverse order of disassembly. (Figure D)
(Figure D)
17
INSTALLATION INSTRUCTIONS FOR PART 99-7001
KNOWLEDGE IS POWER
REV. 8/13/2014 INST99-7001
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
METRA. The World’s best kits.™
1-800-221-0932
metraonline.com
© COPYRIGHT 2004-2014 METRA ELECTRONICS CORPORATION
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement