User's Guide Using the UCD3138ALLCEVM150 Literature Number: SLUUB97A

User's Guide Using the UCD3138ALLCEVM150 Literature Number: SLUUB97A
Using the UCD3138ALLCEVM150
User's Guide
Literature Number: SLUUB97A
March 2015 – Revised January 2016
WARNING
Always follow TI’s set-up and application instructions, including use of all interface components within their
recommended electrical rated voltage and power limits. Always use electrical safety precautions to help
ensure your personal safety and the safety of those working around you. Contact TI’s Product Information
Center http://support/ti./com for further information.
Save all warnings and instructions for future reference.
Failure to follow warnings and instructions may result in personal injury, property damage, or
death due to electrical shock and/or burn hazards.
The term TI HV EVM refers to an electronic device typically provided as an open framed, unenclosed
printed circuit board assembly. It is intended strictly for use in development laboratory environments,
solely for qualified professional users having training, expertise, and knowledge of electrical safety risks in
development and application of high-voltage electrical circuits. Any other use and/or application are strictly
prohibited by Texas Instruments. If you are not suitably qualified, you should immediately stop from further
use of the HV EVM.
1. Work Area Safety:
(a) Keep work area clean and orderly.
(b) Qualified observer(s) must be present anytime circuits are energized.
(c) Effective barriers and signage must be present in the area where the TI HV EVM and its interface
electronics are energized, indicating operation of accessible high voltages may be present, for the
purpose of protecting inadvertent access.
(d) All interface circuits, power supplies, evaluation modules, instruments, meters, scopes and other
related apparatus used in a development environment exceeding 50 VRMS/75 VDC must be
electrically located within a protected Emergency Power Off (EPO) protected power strip.
(e) Use a stable and non-conductive work surface.
(f) Use adequately insulated clamps and wires to attach measurement probes and instruments. No
freehand testing whenever possible.
2. Electrical Safety:
(a) De-energize the TI HV EVM and all its inputs, outputs, and electrical loads before performing any
electrical or other diagnostic measurements. Revalidate that TI HV EVM power has been safely deenergized.
(b) With the EVM confirmed de-energized, proceed with required electrical circuit configurations, wiring,
measurement equipment hook-ups and other application needs, while still assuming the EVM circuit
and measuring instruments are electrically live.
(c) Once EVM readiness is complete, energize the EVM as intended.
WARNING: while the EVM is energized, never touch the EVM or its electrical circuits as they
could be at high voltages capable of causing electrical shock hazard.
3. Personal Safety:
(a) Wear personal protective equipment e.g. latex gloves and/or safety glasses with side shields or
protect EVM in an adequate lucent plastic box with interlocks from accidental touch.
4. Limitation for Safe Use:
(a) EVMs are not to be used as all or part of a production unit.
2
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Introduction
www.ti.com
User's Guide
SLUUB97A – March 2015 – Revised January 2016
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC
Converter
0.1
Introduction
The UCD3138ALLCEVM150 EVM helps evaluate the UCD3138A 64-pin digital control device in an off-line
power converter application and then to aid in its design. The EVM is a standalone LLC resonant halfbridge DC-to-DC power converter. The EVM is used together with its control card, the
UCD3138ACCEVM149 EVM. The UCD3138ARGC is placed on the UCD3138ACCEVM149 EVM.
The UCD3138ALLCEVM150 and UCD3138ACCEVM149 devices can be used as delivered without
additional work, from either hardware or firmware, to evaluate an LLC resonant half-bridge DC-to-DC
converter. This EVM combination allows for some of its design parameters to be returned using a GUI
based tool, called Texas Instruments Fusion Digital Power Designer. It is also possible to load custom
firmware with user’s own definition and development.
The two EVMs included are the UCD3138ALLCEVM150 and the UCD3138ACCEVM149.
This user’s guide provides basic evaluation instruction from a viewpoint of system operation in a
standalone LLC resonant half-bridge DC-to-DC power converter.
WARNING
•
•
•
•
•
•
High voltages are present on this evaluation module during operation and
for a while even after power off. This module should only be tested by
skilled personnel in a controlled laboratory environment.
An isolated DC voltage source meeting IEC61010 reinforced insulation
standards is recommended for evaluating this EVM.
High temperature exceeding 60°C may be found during EVM operation and
for a while even after power off.
This EVM’s purpose is to facilitate the evaluation of digital control in an LLC
using the UCD3138A, and cannot be tested and treated as a final product.
Extreme caution should be taken to eliminate the possibility of electric shock
and heat burn.
Read and understand this user’s guide thoroughly before starting any
physical evaluation.
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
Copyright © 2015–2016, Texas Instruments Incorporated
3
Description
0.2
www.ti.com
Description
The UCD3138ALLCEVM150 and UCD3138ACCEVM149 demonstrate an LLC resonant half-bridge DCDC power converter with digital control using the UCD3138A device. The UCD3138A device is located on
the UCD3138ACCEVM149 board. The UCD3138ACCEVM149 is a daughter card with preloaded firmware
that provides the required control functions for an LLC converter. For details of the firmware please
contact TI. UCD3138ALLCEVM150 accepts a DC input from 350 VDC to 400 VDC, and outputs a nominal
12 VDC with full load output power of 340 W, or full output current of 29 A.
NOTE: This EVM does not have an input fuse and relies on the input current limit from the input
voltage source used.
0.2.1 Typical Applications
•
•
•
Offline DC-to-DC Power Conversion
Servers
Telecommunication Systems
0.2.2 Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
4
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Power Conversion
DC Input from 350 VDC to 400 VDC
12 VDC Regulated Output from No Load to Full Load
Full-Load Power 340 W, or Full-Load Current 29 A
High Efficiency
Constant Soft-Start Time
Protection: Over Voltage, Over Current, Brownout and Output Short-Circuit Protection
Test Points to Facilitate Device and Topology Evaluation
Synchronous Rectification
Automatic Mode Switching between LLC Mode and PWM Mode
Cycle-by-Cycle Current Limiting with Duty Cycle Matching
Constant Current and Constant Power Control Mode
PMBUS Communication
Current Sharing Capability (GUI Enable), Across Paralleled Units
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Performance Specifications
www.ti.com
0.3
Performance Specifications
Table 0-1. UCD3138ALLCEVM150 Performance Specifications
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
Input Characteristics
Voltage operation range
350
Input UVLO On
400
VDC
A
325
Input UVLO Off
310
Input current
Input = 350 VDC, full load = 29 A
1.2
Input current
Input = 380 VDC, full load = 29 A
1.1
Input current
Input = 400 VDC, full load = 29 A
1.0
Output Characteristics
Output voltage, VOUT
No load to full load
12
Output load current, IOUT
350 VDC to 400 VDC
Output voltage ripple
380 VDC and full load = 29 A
Output over current
Operation 10s then latch-off shutdown
30
Resonant mode
35
VDC
29
200
A
mVpp
A
Systems Characteristics
Switching frequency
PWM Mode
150
kHz
150
Peak efficiency
380 VDC, full load = 29 A
94.85%
Full-load efficiency
380 VDC, load = 20 A
94.20%
Operating temperature
Natural convection
25
ºC
Firmware
Device ID (version)
UCD3138A
Filename
3138ALLCEVM_150_150205.x0
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
Copyright © 2015–2016, Texas Instruments Incorporated
5
Schematics
0.4
www.ti.com
Schematics
Bias_&_Control
TP1
External
J2
Power Input
DGND Test Point
J1
Bias power generation
DGND
BUS+_HV_PRI
VAUX_P
VAUX_P = +12V
DGND
12VS
U1
1
VIN+
3
R1
1.47k
VinAux
4
C1
0.1µF
12VOUT
400V Monitor
R2
5
1.00
6
C2
0.1µF
VIN-/VAUX RTN
2
VIN-
12VP_LED
GND
C3
2.2µF
7
PWR050
EAN2
EAN1
EAN0
IO_SEN-
C4
0.1µF
-VO_SENSE
J3
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
AD00
AD01
AD02
AD03
AD04
AD05
AD06
AD07
AD08
AD09
AD10
AD11
AD12
AD13
EAP2
EAP1
EAP0
DPWM0A
DPWM1A
DPWM2A
ADDRESS
VIN_MON
ISHARE
+VO_SENSE
IPS
VOSADC12
VIN_MON
OVLATCH
ORING_CTRL
P_GOOD
EXT_OVP_DISABLE
SCI_TX1
PWM0
TEMP
IO_SENSE
SCI_TX0
AC_P_FAIL_IN
IO_SEN+
EADC_IOSENSE
+VO_SENSE
12VS
DPWM0A
DPWM1A
DPWM2A
DPWM3A
1
3
5
7
9
FAULT0 11
FAULT1 13
SYNC
15
FAULT2 17
19
21
SCI_TX1 23
PWM_0
25
27
TCAP
29
SCI_TX0 31
INT_EXT 33
35
37
12V_EXT 39
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
DPWM0B
DPWM1B
DPWM2B
DPWM3B
FAULT3
SCI_RX1
PWM_1
SCI_RX0
ADC_EXT
/RESET
DPWM0B
DPWM1B
DPWM2B
SR_CTRL
DCT0
DCT1
ON/OFF
SCI_RX1
AC_P_FAIL_OUT
SCI_RX0
FAILURE
3_3VD
3.3V
GND_PWR
D1
Green
DGND
DGND
DGND
3_3VD
AGND
GND_PWR_PRI
GND_PWR
AGND
VIN_MON
GND_PWR_PRI
D2
BAT54S
VIN_MON=1.93V at VIN=400V
DGND
3_3VD
TPS715A33DRBR
3_3V_P
U2A
U8
1
8
6
7
5
OUT
NC
NC
FB/NC
IN
OUT
3_3VA
8
GND
R3
9
IN
NC
NC
GND
PAD
4
1
2
3
4
3_3VA
1.00
TPS715A33DRB
C5
0.1µF
C7
1µF
C46
1µF
DGND
DGND
DGND/AGND Damping
AGND
1
C47
0.1µF
C6
0.1µF
R4
301
3_3VD_LED
DGND
R5
2
D3
Green
10.0
3.3VD LED Indicator
DGND
GND_PWR_PRI
AGND
DGND
Figure 0-1. UCD3138ALLCEVM150 Schematics (1 of 9)
LED Indicators
3_3VD
3_3VD
3_3VD
On/off control
R6
301
3_3VD
R7
301
R8
301
AC_P_FAIL_OUT_LED
R9
5.11k
D4
Red
D5
Green
D6
Red
5
ON/OFF
S1
G12AP
C8
0.1µF
Q1
2N7002-7-F
FAILURE
Q2
2N7002-7-F
P_GOOD
Q3
2N7002-7-F
AC_P_FAIL_OUT
4
OFF
6
ON
DGND
DGND
DGND
DGND
Device Address
I Share Bus
ADDRESS
J4
ISHARE
R10
C9
0.01µF
C10
AGND
AGND
AGND
Figure 0-2. UCD3138ALLCEVM150 Schematics (2 of 9)
6
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Schematics
www.ti.com
Current Share Compensation
R11
Output Current Sense
PWM0
3_3VA
+12VEXT
R12
IO_SENSE
1.00k
C11
0.1µF
R14
549
C12
0.1µF
5
U3
OPA376AIDBVR
AGND
R13
549
TP2
R16
100
TP3
1
R17
IO_SEN+
3
R19
35.7k
+12VFB
AGND
R18
1.00k
EADC_IOSENSE
1.00k
2
1mV/1A
R15
549
1.6V/35A
4
IOSFB
C13
220pF
D7
MMBD914
+12V
C14
0.01µF
R20
AGND
AGND
C15
+VO_SENSE
10.0k
AGND
220pF
IO_SEN-
R22
R23
1.00k
35.7k
R21
1.00k
C16
2200pF
Voltage Feedback
AGND
R24
AGND
-VO_SENSE
10.0k
ADC12 Monitoring and Protection
R25
1.00k
C17
2200pF
+12V
Temperature Sense
12V_RTN
LM20BIM7/NOPB
AGND
AGND
TEMPERATURE = 159.6 C - TEMP * 85.5 C/V
3_3VA
R26
10.0k
U4
4
V+
VO
NC
3
1
TEMP
2
5
GND
R27
100
C18
0.01µF
C19
0.01µF
VOSADC12
R28
1.00k
AGND
C20
2200pF
AGND
AGND
Figure 0-3. UCD3138ALLCEVM150 Schematics (3 of 9)
Redundant OVP circuit.
3_3VD
R29
20.0k
R30
100
UART
OVLATCH
SCI Interface
R31
100
J5
V+ = +5.4V
10
3_3VD
1
6
2
7
3
8
4
9
5
V- = -5.4V
+12V
U5
Q4A
MMDT4413-7-F
11
9
SCI_TX1
SCI_RX1
Q4B
MMDT4413-7-F
12
16
R32
20.0k
1
2
C21
0.1µF
4
3
Q5
2N7002-7-F
EXT_OVP_DISABLE
J6
R33
1.00k
C24
0.1µF
C26
0.1µF
15
DIN
ROUT
FORCEON
FORCEOFF
DOUT
RIN
INVALID
13
8
10
11
EN
C1+
C2+
C1-
C2-
V+
V-
VCC
GND
5
182-009-213R171
C23
0.1µF
6
7
C25
0.1µF
14
DGND
SN65C3221PW
R34
10.0k
DGND
C22
0.1µF
External OVP Disable
DGND
DGND
3_3VD
PFC Communication Connector
SCI_TX0
1
3
5
2
4
6
SCI_RX0
AC_P_FAIL_IN
J7
DGND
Figure 0-4. UCD3138ALLCEVM150 Schematics (4 of 9)
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
Copyright © 2015–2016, Texas Instruments Incorporated
7
Schematics
www.ti.com
Pri_Gate_Drive
VIN = 350 to 400VDC, Iin max = 1.5A.
TP5
TP4
VAUX_P
VIN_HV_PRI
TP6
J8
BUS+_HV_PRI
R39
R35
5.1
2.2
D8
923345-07-C
C34
2.2µF
TP7
C30
47 µF
J9
HSG
10.0
MURS360T3G
J10
ED120/2DS
R36
R37
5.11k
C28
2.2µF
C35
0.1µF
U6
C31
1.5 µF
7
GND_PWR_PRI
VDD
HB
NC/EN
HO
HI
HS
LI
LO
13
GND_PWR_PRI
4
ED120/2DS
R59
1
51
GND_PWR_PRI
R60
2
51
12
11
HSS
6
TP8
C27
220pF
R43
10.0k
C29
220pF
8
9
10
14
R38
10.0k
NC
NC
NC
NC
COM
VSS
5
R41
3
LSG
10.0
UCC27714D
R42
5.11k
U7
3
4
5
6
DPWM0A
DPWM0B
3_3VD
7
1
2
8
C33
0.1µF
INA
INB
INC
IND
OUTA
OUTB
OUTC
OUTD
DISABLE
CTRL
VCC1
VCC2
GND1
GND1
GND2
GND2
14
13
12
11
GND_PWR_PRI
GND_PWR_PRI
GND_PWR_PRI
3_3V_P
GND_PWR_PRI
10
16
C32
0.1µF
9
15
ISO7240CFQDWRQ1
GND_PWR
GND_PWR_PRI
Figure 0-5. UCD3138ALLCEVM150 Schematics (5 of 9)
BUS+_HV_PRI
300VDC to 400VDC / 2A
Power_Stage
EMI Suppression
C39
HS1
2200 pF
C36
0.015 µF
Q6
SPW20N60CFD
C37
0.015 µF
C38
0.015 µF
HSG
GND_PWR_PRI
1
2
GND_PWR
GND_PWR_PRI
TP9
VRC
+12V
16:1:1
TRP1
5
4
3
8
7
6
L1
11698
T1
8
7
1
HSS
2
6
5
TRP2
TP10
4
3
11697
TP12
TP11
LSG
C40
0.015 µF
C41
0.015 µF
HS6
T2
CS4200V-01L
C42
0.015 µF
1
1
2
3
2
HS2
HS5
HS3
SR_VDS1
Q9
IRLB3036PBF
Q10
IRLB3036PBF
HS4
SR_VDS2
Q11
IRLB3036PBF
4
Q7
SPW20N60CFD
IRLB3036PBF
GND_PWR_PRI
TP13
D10
BAT54S
Primary Current Sense
VCDS1
VCSS2
Q8
IPS
0.312V/A
R44
1.00
C43
100pF
R51
124
R45
1.00
R46
1.00k
R47
1.00
R50
124
R48
1.00
R49
1.00k
GND_PWR
SR1
SR2
D9
BAT54S
AGND
AGND
Figure 0-6. UCD3138ALLCEVM150 Schematics (6 of 9)
8
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Schematics
www.ti.com
12VS
C45
0.1µF
C44
2.2µF
GND_PWR
GND_PWR
TP14
U9
3
1
DPWM1A
R56
0
DCT0
2
6
SR_CTRL
C49
DGND
R58
10.0k
SR_Control
SR gate drivers
VCC
OUT
IN
VD
4
SR1
R52
5
SR_VDS1
20.0
DCT
CTRL
GND
7
UCD7138DRS
GND_PWR
GND_PWR
12VS
C51
2.2µF
GND_PWR
C52
0.1µF
GND_PWR
TP15
U10
3
1
DPWM1B
R63
0
DCT1
2
6
SR_CTRL
C56
DGND
R64
10.0k
VCC
OUT
IN
VD
4
5
SR2
R53
20.0
SR_VDS2
DCT
CTRL
GND
7
UCD7138DRS
GND_PWR
GND_PWR
Figure 0-7. UCD3138ALLCEVM150 Schematics (7 of 9)
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
Copyright © 2015–2016, Texas Instruments Incorporated
9
Schematics
www.ti.com
+12V
Diode Oring Control
12VS
+12V
R66
10.0k
R67
10.0
R69
10.0k
+12VEXT
R70
549
OUTPUT
U11
1
2
DGND
3
4
6
5
ORING_CTRL
7
R65
100k
R62
10.0k
VDD
PG
RSET
BYP
STAT
FLTR
FLTB
A
UV
C
OV
RSVD
GND
GATE
14
C57
2200pF
C58
100pF
R68
5.11k
13
12
11
C59
100pF
10
9
8
C60
0.01µF TPS2411PWR
+12VEXT
C61
0.01µF
J13
1
4
2
3
4
5
Oscilloscope socket.
CSD16325Q5
5,6,
7,8
1,2,3
C62
0.1µF
+12VEXT
DGND
Output capacitor bank
Q13
TP17
NT4
4
TP18
+12V
1,2,3
Net-Tie
5,6,
7,8
J11
12V_RTN
Q12
CSD16325Q5
VOUT = 12V
NT5
IOUT = 0A to 29A
Net-Tie
C64
470µF
C63
470µF
POUT = 340W max
C66
470µF
C65
470µF
Bleeder
C67
470µF
C68
47µF
C55
47µF
C54
47µF
C53
47µF
C48
4.7µF
C50
47µF
R61
1.00k
R57
1.00k
Resistors
R55
0.003
R54
TP19
TP16
0.003
J12
R40
0.003
GND_PWR
NT1
Net-Tie
12V_RTN
NT2
Net-Tie
NT3
Net-Tie
IO_SEN+
Load current sense
DGND
IO_SEN-
Figure 0-8. UCD3138ALLCEVM150 Schematics (8 of 9)
10
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Schematics
www.ti.com
H1
H2
H3
H4
H9
H11
4824
4824
4824
4824
4824
4824
H5
H6
H7
H8
H10
H12
1903C
1903C
1903C
1903C
1903C
1903C
FID1
FID2
FID3
FID4
PCB Number: SV601150
PCB Rev: A
FID5
FID6
PCB
LOGO
Texas Instruments
DANGER HIGH VOLTAGE DANGER HIGH VOLTAGE
DANGER HIGH VOLTAGE
DANGER HIGH VOLTAGE
CAUTION HOT SURFACE
CAUTION HOT SURFACECAUTION HOT SURFACE
PCB
LOGO
CAUTION HOT SURFACECAUTION HOT SURFACE
CAUTION HOT SURFACE CAUTION HOT SURFACE
CAUTION HOT SURFACE
FCC disclaimer
PCB
LOGO
DANGER HIGH VOLTAGE
PCB
LOGO
CAUTION HOT SURFACE
CAUTION.
READ USER GUIDE BEFORE USE
Pb-Free Symbol
SH-J1
ZZ1
Assembly Note
These assemblies are ESD sensitive, ESD precautions
shall be observed.
ZZ2
Assembly Note
These assemblies must be clean and free from flux
nd all
a contaminants. Use of no clean flux is not
ceptable.
ac
ZZ3
Assembly Note
These assemblies must comply with workmanship stand
ards IPC-A-610 Class 2, unless otherwise specified.
H13
MECH
SP900S-0.009-00-104
H14
MECH
4880SG
H18
MECH
4880SG
H15
MECH
4880SG
H20
MECH
SP900S-0.009-00-104
H16
MECH
4880SG
H17
MECH
4880SG
H19
MECH
4880SG
H21
MECH
3138ACC32EVM-149
H22
MECH
HPA172
Figure 0-9. UCD3138ALLCEVM150 Schematics (9 of 9)
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
Copyright © 2015–2016, Texas Instruments Incorporated
11
Test Setup
0.5
www.ti.com
Test Setup
0.5.1 Test Equipment
DC Voltage Source: capable of 350 VDC to 400 VDC, adjustable, with minimum power rating of 400 W, or
current rating not less than 1.5 A, with current limit function. The DC voltage source to be used should
meet IEC61010 safety requirements.
DC Multimeter: One unit capable of 0-VDC to 400-VDC input range, four digits display preferred; and one
unit capable of 0-VDC to 15-VDC input range, four digits display preferred.
Output Load: DC load capable of receiving 0 VDC to 15 VDC, 0 A to 30 A, and 0 W to 360 W or greater,
with display such as load current and load power.
Current-meter, DC, optional in case the load has no display, one unit, capable of 0 A to 30 A. A low ohmic
shunt and DMM are recommended.
Oscilloscope: capable of 500-MHz full bandwidth, digital or analog, if digital 5 Gs/s or better.
Fan: 200 LFM to 400 LFM forced air cooling is recommended, but not a must.
Recommended Wire Gauge: capable of 30 A, or better than number 14 AWG, with the total length of
wire less than 8 feet (a four foot input and a four foot return).
0.5.2 Recommended Test Setup
Figure 0-10. UCD3138ALLCEVM150 Recommended Test Set Up
12
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Test Setup
www.ti.com
Figure 0-11. Orientation of Board UCD3138ACCEVM149 on Board UCD3138ALLCEVM150
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
Copyright © 2015–2016, Texas Instruments Incorporated
13
List of Test Points
0.6
www.ti.com
List of Test Points
Table 0-2. UCD3138ACCEVM149 Test Points
0.7
TEST POINTS
NAME
TP1
DGND
TP2
Not Used
TP3
Not Used
DESCRIPTION
Digital GND
TP4
HSG
TP5
Input +
Primary high-side MOSFET gate, Q6
Input + after jumper J10
TP6
Input_P
Input voltage positive terminal
TP7
Input_N
Input voltage return terminal
TP8
LSG
Primary low-side MOSFET gate, Q7
TP9
HSS
Primary-side switch node, or the intersection of Q6 and Q7
TP10
SWC
Primary side, the intersection of bridge capacitors
TP11
SR_VDS1
Drain of secondary side sync FET Q8 and Q9
TP12
SR_VDS2
Drain of secondary side sync FET Q10 and Q11
TP13
IPS
Primary current sense
TP14
SR1
SR gate drive to Q8 and Q9
TP15
SR2
SR gate drive to Q10 and Q11
TP16
Vo_N
Output voltage return
TP17
Vo_P
Output voltage positive terminal
TP18
Xmer_C
TP19
GND_PWR
Power transformer center point of the secondary side windings.
Power GND
List of Terminals
Table 0-3. List of Terminals
TERMINAL
14
NAME
DESCRIPTION
J1
Bias Input
J2
Analog Signal
3 pin, external power input, 12 V
40-pin header, analog signal to control card (UCD3138ACCEVM149)
J3
Digital Signal
40-pin header, digital signal to control card
J4
I-Share
Current share bus connector, 3-pin
J5
UART1
Standard UART connection, RS232, 9 pin
J6
OVP-1
2-pin header, jump across to disable external OVP
J7
Not Used
J8
Input_P
Input voltage positive terminal
J9
Input_N
Input voltage return terminal
J10
Jumper
Reserved to an input fuse substitution
J11
Output_P
Output voltage positive terminal
J12
Output_N
Output voltage return terminal
J13
Vout
Oscilloscope socket
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Test Procedure
www.ti.com
0.8
Test Procedure
0.8.1 Efficiency Measurement Procedure
WARNING
•
•
•
Danger of electrical shock! High voltage present during the measurement.
Do not leave EVM powered when unattended.
Danger of heat burn from high temperature.
1. Refer to Figure 0-10 for basic set up to measure power conversion efficiency. The required equipment
for this measurement is listed in Section 0.5.1.
2. Before making electrical connections, visually check the boards to make sure no shipping damage
occurred.
3. In this EVM package, two EVMs are included, UCD3138ALLCEVM150, and the
UCD3138ACCEVM149. For this measurement, the UCD3138ALLCEVM150 and
UCD3138ACCEVM149 boards are needed.
4. First install the UCD3138ACCEVM149 board onto the UCD3138ALLCEVM150. Care must be taken
with the alignment and orientation of the two boards, or damage may occur. Refer to Figure 0-11 for
UCD3138ACCEVM149 board orientation.
5. Connect the DC voltage source to J8 (+) and J9 (-). The DC voltage source should be isolated and
meet IEC61010 requirements. Set up the DC output voltage in the range specified in Table 0-1,
between 350 VDC and 400 VDC; set up the DC source current limit 1.2 A.
NOTE: The board has no fuse installed and relies on the external voltage source current limit for
circuit protection.
6. Connect an electronic load with either constant-current mode or constant-resistance mode. The load
range is from zero to 29 A.
7. Check and make sure a jumper is installed on J6.
8. It is recommended to use the switch SW1 to turn on the board output after the input voltage is applied
to the board. Before applying input voltage, make sure the switch, SW1, is in the OFF position.
9. If the load does not have a current or a power display, a current meter or low ohmic shunt and DMM is
needed between the load and the board for current measurements.
10. Connect a volt-meter across the output connector and set the volt-meter scale 0 V to 15 V on its
voltage, DC.
11. Turn on the DC voltage source output, flip SW1 to ON and vary the load. Record output voltage and
current measurements.
0.8.2 Equipment Shutdown
1. Shut down the DC voltage source.
2. Shut down the electronic load.
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
Copyright © 2015–2016, Texas Instruments Incorporated
15
Performance Data and Typical Characteristic Curves
0.9
www.ti.com
Performance Data and Typical Characteristic Curves
Figure 0-12 through Figure 0-25 present typical performance curves for UCD3138ALLCEVM150.
0.9.1 Efficiency
0.96
0.94
Efficiency (%)
0.92
0.9
0.88
0.86
0.84
350 VDC
380 VDC
400 VDC
0.82
5
7.5
10
12.5
15 17.5 20 22.5
Load Current (A)
25
27.5
30
D001
Figure 0-12. UCD3138ALLCEVM150 Efficiency
0.9.2 Load Regulation
12.3
12.2
12.1
Load Regulation (V)
12
11.9
11.8
11.7
11.6
11.5
350 VDC
380 VDC
400 VDC
11.4
11.3
5
7.5
10
12.5
15 17.5 20 22.5
Load Current (A)
25
27.5
30
D001
Figure 0-13. UCD3138ALLCEVM150 Load Regulation
16
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Performance Data and Typical Characteristic Curves
www.ti.com
0.9.3 Switching Frequency Control
135
350 VDC
380 VDC
400 VDC
130
125
120
Switching Frequency (kHz)
115
110
105
100
95
90
85
80
75
70
65
60
55
50
45
5
7.5
10
12.5
15 17.5 20 22.5
Load Current (A)
25
27.5
30
D001
Figure 0-14. Switching Frequency Control in LLC Mode
0.9.4 Load Operation with LLC and PWM
Figure 15. LLC Resonant Mode Operation at Full Load
(Ch1 = VGS of Q7, Ch2 = current in resonant network, 2
A/div, Ch3 = VDS of Q7, Ch4 = VO ripple)
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Figure 16. PWM Mode Operation after FSW = 150 kHz
(Ch1 = VGS of Q7, Ch2 = VGS of Q6, Ch3 = VGS of SR2, Ch4 =
VGS of SR3)
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
Copyright © 2015–2016, Texas Instruments Incorporated
17
Performance Data and Typical Characteristic Curves
www.ti.com
0.9.5 Very Light-Load Operation at High Line of Input
Figure 17. PWM Control at 400VDC Input and Light Load
(SR off)
(Ch1 = VGS, Q7, Ch2 = VGS, Q6, Ch3 = VGS, SR1, Ch4 = VGS,
SR2)
Figure 18. PWM Control with SR Off and Pulse Skipping
(Ch1 = VGS, Q7, Ch2 = VGS, Q6, Ch3 = VGS, SR1, Ch4 = VGS,
SR2)
0.9.6 Output Voltage Ripple
Figure 19. Output Voltage Ripple 380 VDC and Full Load
18
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
Figure 20. Output Voltage Ripple 380 VDC and Half Load
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Performance Data and Typical Characteristic Curves
www.ti.com
0.9.7 Output Turn On
Figure 21. Output Turn On 380 VDC with Load Range
Figure 22. Output Turn On 350 VDC with Load Range
0.9.8 Other Waveforms
Figure 0-23. 380 VDC and 30 A Before OCP Latch-Off Shutdown
(Ch1 = VDS of Q7, Ch2 = current of resonant network, Ch3 = VO ripple)
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
Copyright © 2015–2016, Texas Instruments Incorporated
19
Performance Data and Typical Characteristic Curves
www.ti.com
150
Gain
Phase 120
Gain (dB)
40
30
90
20
60
10
30
0
0
-10
-30
-20
-60
-30
-90
-40
-120
-50
100
200 300
500 700 1000
2000 3000 5000
Frequency (Hz)
Phase (°)
50
-150
10000
D001
D008
D002
Figure 0-24. Control Loop Bode Plots at 380 VDC and Full Load
150
Gain
Phase 120
Gain (dB)
40
30
90
20
60
10
30
0
0
-10
-30
-20
-60
-30
-90
-40
-120
-50
100
200 300
500 700 1000
2000 3000 5000
Frequency (Hz)
Phase (°)
50
-150
10000
D001
D008
D002
Figure 0-25. Control Loop Bode Plots at 400 VDC and Full Load
20
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
EVM Assembly Drawing and PCB layout
www.ti.com
0.10 EVM Assembly Drawing and PCB layout
The following figures (Figure 0-26 through Figure 0-31) show the design of the UCD3138ALLCEVM150
printed circuit board. PCB dimensions: L x W = 8.0 inch x 6.0 inch, PCB material: FR4 or compatible, four
layers and 2-ounce copper on each layer
Figure 0-26. UCD3138ALLCEVM150 Top Layer Assembly Drawing (Top View)
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
Copyright © 2015–2016, Texas Instruments Incorporated
21
EVM Assembly Drawing and PCB layout
www.ti.com
Figure 0-27. UCD3138ALLCEVM150 Bottom Assembly Drawing (Bottom View)
22
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
EVM Assembly Drawing and PCB layout
www.ti.com
Figure 0-28. UCD3138LLCEVM150 Top Copper (Top View)
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
Copyright © 2015–2016, Texas Instruments Incorporated
23
EVM Assembly Drawing and PCB layout
www.ti.com
Figure 0-29. UCD3138LLCEVM150 Internal Layer 1 (Top View)
24
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
EVM Assembly Drawing and PCB layout
www.ti.com
Figure 0-30. UCD3138LLCEVM150 Internal Layer 2 (Top View)
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
Copyright © 2015–2016, Texas Instruments Incorporated
25
EVM Assembly Drawing and PCB layout
www.ti.com
Figure 0-31. UCD3138LLCEVM150 Bottom Copper (Top View)
26
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
List of Materials
www.ti.com
0.11 List of Materials
Component list based on Figure 0-10 and Figure 0-11.
Table 0-4. UCD3138LLCEVM150 List of Materials
REFERENCE DESIGNATOR
DESCRIPTION
PART NO.
MANUFACTURER
!PCB
QTY
1
Printed Circuit Board
SV601150
Any
C1, C2, C4, C5, C6, C8, C11, C12,
C21, C22, C23, C24, C25, C26, C32,
C33, C35, C45, C52, C62
20
Capacitor, ceramic, 0.1 µF, 16 V, ±10%, X7R, 0603
C0603C104K4RACTU
Kemet
C3, C28, C34, C44, C51
5
Capacitor, ceramic, 2.2 µF, 16 V, ±10%, X5R, 0603
GRM188R61C225KE15D
MuRata
C7, C46
2
Capacitor, ceramic, 1 µF, 16 V, ±10%, X7R, 0603
C1608X7R1C105K
TDK
C9, C14, C18, C19, C60, C61
6
Capacitor, ceramic, 0.01 µF, 16 V, ±10%, X7R, 0603
GRM188R71C103KA01D
MuRata
C10
0
Capacitor, ceramic, 0.1 µF, 16 V, ±10%, X7R, 0603
C0603C104K4RACTU
Kemet
C13, C15
2
Capacitor, ceramic, 220 pF, 50 V, ±10%, X7R, 0603
C0603C221K5RACTU
Kemet
C16, C17, C20, C57
4
Capacitor, ceramic, 2200 pF, 50 V, ±10%, X7R, 0603
C0603C222K5RAC
Kemet
C27, C29
2
Capacitor, ceramic, 220 pF, 100 V, ±10%, X7R, 0603
06031C221KAT2A
AVX
C30
1
Capacitor, aluminum, 47 µF, 450 V, ±-20%, TH
LGU2W470MELY
Nichicon
C31
1
Capacitor, film, 1.5 µF, 450 V, ±10%, TH
ECQ-E2W155KH
Panasonic
C36, C37, C38, C40, C41, C42
6
Capacitor, film, 0.015 µF, 630 V, ±5%, TH
ECWF6153JL
Panasonic
C39
1
Capacitor, film, 2200 pF, 3000 V, ±20%, TH
B81123C1222M
EPCOS Inc
C43, C58, C59
3
Capacitor, ceramic, 100 pF, 25 V, ±10%, X7R, 0603
06033C101KAT2A
AVX
C47
1
Capacitor, ceramic, 0.1 µF, 16 V, ±5%, X7R, 0603
0603YC104JAT2A
AVX
C48
1
Capacitor, ceramic, 4.7 µF, 50 V, ±10%, X7R, 1210
GRM32ER71H475KA88L
MuRata
C49, C56
0
Capacitor, ceramic, 100 pF, 25 V, ±10%, X7R, 0603
06033C101KAT2A
AVX
C50, C53, C54, C55, C68
5
Capacitor, ceramic, 47 µF, 16 V, ±20%, X5R, 1210
GRM32ER61C476ME15L
MuRata
C63, C64, C65, C66, C67
5
Capacitor, aluminum, 470 µF, 16 V, ±20%, 0.009 Ω, TH
PLF1C471MDO1
Nichicon
D1, D3, D5
3
LED, green, SMD
LTST-C190GKT
Lite-On
D2, D9, D10
3
Diode, Schottky, 30 V, 0.2 A, SOT-23
BAT54S-E3-08
Vishay-Semiconductor
D4, D6
2
LED, red, SMD
LTST-C190CKT
Lite-On
D7
1
Diode, P-N, 100 V, 0.2 A, SOT-23
MMBD914
Fairchild Semiconductor
D8
1
Diode, ultrafast, 600 V, 3 A, SMC
MURS360T3G
ON Semiconductor
H1, H2, H3, H4, H9, H11
6
HEX standoff 6-32 nylon 1-1/2"
4824
Keystone
H5, H6, H7, H8, H10, H12
6
Standoff, hex, 0.5"L #6-32 nylon
1903C
Keystone
H13, H20
2
Large thermal pad to substitute for the smaller one in the TO-247 mounting
kit
SP900S-0.009-00-104
Bergquist
H14, H15, H16, H17
4
TO-220 mounting kit
4880SG
Aavid Thermalloy
H18, H19
2
TO-247 mounting kit
4880SG
Aavid Thermalloy
H21
1
3138ACC32EVM-149
3138ACC32EVM-149
Texas Instruments
H22
1
USB to GPIO adaptor
HPA172
Used in BOM report
HS1, HS2
2
Heat sink TO-218/TO-247 W/pins 2"
513201B02500G
Aavid
HS3, HS4, HS5, HS6
4
Heat sink, TO-220
507302B00000G
Aavid
J1
1
Conn header 3 pos .100 vert tin
22-27-2031
Molex
J2, J3
2
Header, 2mm, 20 x 2, gold, TH
87758-4016
Molex
J4
1
Header, 100mil, 3 x 1, tin, TH
PEC03SAAN
Sullins Connector Solutions
J5
1
Conn DB9 female R/A solder TH
182-009-213R171
NorComp
J6
1
Header, 100 mil, 2 x 1, tin, TH
PEC02SAAN
Sullins Connector Solutions
J7
0
Header, 100 mil, 3 x 2, tin, TH
PEC03DAAN
Sullins Connector Solutions
J8, J9, J11, J12
4
Terminal block 5.08 mm vetricle 2pos, TH
ED120/2DS
On-Shore Technology
J10
1
Jumper wire, 700-mil spacing, violet, pkg of 150, TH
923345-07-C
3M
J13
1
Compact probe tip circuit board test points, TH, 25 per
131-5031-00
Tektronix
L1
1
Inductor, , TH
11698
Payton
Q1, Q2, Q3, Q5
4
MOSFET, N-channel, 60 V, 0.17 A, SOT-23
2N7002-7-F
Diodes Inc.
Q4
1
Transistor, NPN/PNP Pair, 40 V, 0.6 A, SOT-363
MMDT4413-7-F
Diodes Inc.
Q6, Q7
2
MOSFET, N-channel, 650 V, 20.7 A, TO-247
SPW20N60CFD
Infineon Technologies
Q8, Q9, Q10, Q11
4
MOSFET, N-channel, 60 V, 195 A, TO-220AB
IRLB3036PBF
International Rectifier
Q12, Q13
0
MOSFET, N-channel, 25 V, 100 A, SON 5 mm x 6 mm
CSD16325Q5
Texas Instruments
R1
1
Resistor, 1.47 kΩ, 1%, 0.125 W, 0805
CRCW08051K47FKEA
Vishay-Dale
R2, R3, R44, R45, R47, R48
6
Resistor, 1.00 Ω, 1%, 0.1 W, 0603
CRCW06031R00FKEA
Vishay-Dale
R4, R6, R7, R8
4
Resistor, 301 Ω, 1%, 0.1 W, 0603
CRCW0603301RFKEA
Vishay-Dale
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
Copyright © 2015–2016, Texas Instruments Incorporated
27
List of Materials
www.ti.com
Table 0-4. UCD3138LLCEVM150 List of Materials (continued)
REFERENCE DESIGNATOR
DESCRIPTION
PART NO.
MANUFACTURER
R5, R67
QTY
2
Resistor, 10.0 Ω, 1%, 0.1 W, 0603
CRCW060310R0FKEA
Vishay-Dale
R9, R37, R42, R68
4
Resistor, 5.11 kΩ, 1%, 0.1 W, 0603
CRCW06035K11FKEA
Vishay-Dale
R10, R11
0
Resistor, 1.00 kΩ, 1%, 0.1 W, 0603
CRCW06031K00FKEA
Vishay-Dale
R12, R17, R18, R21, R22, R25, R28,
R33, R46, R49
10
Resistor, 1.00 kΩ, 1%, 0.1 W, 0603
CRCW06031K00FKEA
Vishay-Dale
R13, R14, R15
3
Resistor, 549 Ω, 1%, 0.25 W, 1206
RC1206FR-07549RL
Yageo America
R16, R27, R30, R31
4
Resistor, 100 Ω, 1%, 0.1 W, 0603
CRCW0603100RFKEA
Vishay-Dale
R19, R23
2
Resistor, 35.7 kΩ, 1%, 0.1 W, 0603
CRCW060335K7FKEA
Vishay-Dale
R20, R24, R26, R34, R38, R43, R58,
R62, R64, R66, R69
11
Resistor, 10.0 kΩ, 1%, 0.1 W, 0603
CRCW060310K0FKEA
Vishay-Dale
R29, R32
2
Resistor, 20.0 kΩ, 1%, 0.1 W, 0603
CRCW060320K0FKEA
Vishay-Dale
R35
1
Resistor, 2.2 Ω, 5%, 0.1 W, 0603
CRCW06032R20JNEA
Vishay-Dale
R36, R41
2
Resistor, 10.0 Ω, 1%, 0.125 W, 0805
RC0805FR-0710RL
Yageo America
R39
1
Resistor, 5.1 Ω, 5%, 0.1 W, 0603
CRCW06035R10JNEA
Vishay-Dale
R40, R54, R55
3
Resistor, 0.003 Ω, 1%, 1 W, 1210
PMR25HZPFV3L00
Rohm
R50, R51
2
Resistor, 124 Ω, 1%, 0.125 W, 0805
CRCW0805124RFKEA
Vishay-Dale
R52, R53
2
Resistor, 20.0 Ω, 1%, 0.1 W, 0603
CRCW060320R0FKEA
Vishay-Dale
R56, R63
2
Resistor, 0 Ω, 5%, 0.1 W, 0603
CRCW06030000Z0EA
Vishay-Dale
R57, R61
2
Resistor, 1.00 kΩ, 1%, 0.125 W, 0805
CRCW08051K00FKEA
Vishay-Dale
R59, R60
2
Resistor, 51 Ω, 5%, 0.1 W, 0603
CRCW060351R0JNEA
Vishay-Dale
R65
1
Resistor, 100 kΩ, 1%, 0.1 W, 0603
CRCW0603100KFKEA
Vishay-Dale
R70
1
Resistor, 549 Ω, 1%, 0.1 W, 0603
CRCW0603549RFKEA
Vishay-Dale
S1
1
Switch, toggle, SPDT 1 pos, TH
G12AP
NKK Switches
SH-J1
1
Shunt, 100 mil, flash gold black
SPC02SYAN
Sullins Connector Solutions
T1
1
Transformer, PQ35/35, TH
11697
Payton
T2
1
Transformer, current sense, 80 mH, TH
CS4200V-01L
Coilcraft
TP1, TP4, TP5, TP6, TP7, TP8, TP9,
TP10, TP11, TP12, TP13, TP14,
TP15, TP16, TP17, TP18, TP19
17
Test point, miniature, white, TH
5002
Keystone
TP2, TP3
0
Test point, miniature, white, TH
5002
Keystone
U1
1
UCC28600EVM, 400 V, 12 V
PWR050
Texas Instruments
U2
1
Single Output LDO, 80 mA, Fixed 3.3 V Output, 2.5 to 24 V Input, with Low
IQ,
8-pin SON (DRB), -40°C to 125°C, Green (RoHS & no Sb/Br)
TPS715A33DRBR
Texas Instruments
U3
1
Precision, Low Noise, Low IQ Operational Amplifier, 2.2 V to 5.5 V, -40°C
to 125°C,
5-pin SOT23 (DBV0005A), Green (RoHS & no Sb/Br)
OPA376AIDBVR
Texas Instruments
U4
1
2.4-V, 10-µA Temperature Sensor, 5-pin SC-70 Micro SMD, Pb-Free
LM20BIM7/NOPB
Texas Instruments
U5
1
3-V to 5.5-V Single-Channel RS-232 Compatible Line Driver/Receiver,
-40°C to 85°C, 16-Pin TSSOP (PW), Green (RoHS & no Sb/Br)
SN65C3221PW
Texas Instruments
U6
1
High-Speed, 4-A, 600-V High-side Low-side Gate Driver Device, D0014A
UCC27714D
Texas Instruments
U7
1
25-Mbps Automotive Catalog Quad, 4/0, Digital Isolator, Selectable
Failsafe,
3.3 V / 5 V, -40°C to 125°C, 16-pin SOIC (DW), Green (RoHS & no Sb/Br)
ISO7240CFQDWRQ1
Texas Instruments
U8
1
High Input Voltage, Micropower SON Packaged,
80-mA, LDO Linear Regulators, DRB0008A
TPS715A33DRB
Texas Instruments
U9, U10
2
UCD7138 Low-Side Power MOSFET Driver
with Body Diode Conduction Sensing
UCD7138DRS
Texas Instruments
U11
0
Full Featured N+1 and ORing Power Rail Controller
TPS2411PWR
Texas Instruments
NOTE: PWR050 is a bias board and its design documents can be found from www.ti.com.
28
Digitally Controlled LLC Resonant Half-Bridge DC-to-DC Converter
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
References
www.ti.com
0.12 References
1. UCD3138A Data Manual, SLUSC66
2. UCD3138ACCEVM149 Evaluation Module and User’s Guide, Programmable Digital Power Controller
Control Card Evaluation Module, SLUUB82
3. Fusion Digital Power Designer GUI for Isolated Power Applications User Guide (for UCD3138,
UCD3138064, UCD3138A Applications), SLUA676
4. Designing an LLC Resonant Half-Bridge Power Converter, SEM1900
5. Feedback Loop Design of an LLC Resonant Power Converter, SLUA582A
6. UCD3138 Digital Power Peripherals Programmer’s Manual, SLUU995
7. UCD3138 Monitoring and Communications Programmer’s Manual, SLUU996
8. UCD3138 ARM and Digital System Programmer’s Manual, SLUU994
Revision History
Changes from Original (March 2015) to A Revision ....................................................................................................... Page
•
•
Deleted USB-to-GPIO from EVM package. ............................................................................................ 3
Deleted USB-to-GPIO from EVM package. .......................................................................................... 15
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
SLUUB97A – March 2015 – Revised January 2016
Submit Documentation Feedback
Copyright © 2015–2016, Texas Instruments Incorporated
Revision History
29
STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES
1.
Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or
documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein.
Acceptance of the EVM is expressly subject to the following terms and conditions.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2
Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software
License Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatment
by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any
way by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications or
instructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or as
mandated by government requirements. TI does not test all parameters of each EVM.
2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM,
or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the
warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to
repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall
be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
3
Regulatory Notices:
3.1 United States
3.1.1
Notice applicable to EVMs not FCC-Approved:
This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit
to determine whether to incorporate such items in a finished product and software developers to write software applications for
use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless
all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause
harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is
designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of
an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1
For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1
Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2
Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified
by TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required by Radio Law of
Japan to follow the instructions below with respect to EVMs:
1.
2.
3.
Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
SPACER
SPACER
SPACER
SPACER
SPACER
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて
いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの
措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社
東京都新宿区西新宿6丁目24番1号
西新宿三井ビル
3.3.3
Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧ください。http:/
/www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
SPACER
4
EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1
User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2
EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.
5.
Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
6.
Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM (AND THE
DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY
THIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS AND
CONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY
OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD
PARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY
INVENTION, DISCOVERY OR IMPROVEMENT MADE, CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OF
THE EVM.
7.
USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS
LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,
EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY
HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS. THIS OBLIGATION
SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY
OTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
8.
Limitations on Damages and Liability:
8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE
TERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER, REGARDLESS OF WHETHER TI HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED
TO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS,
LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL
BE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATION
ARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS, OR ANY USE OF ANY TI EVM
PROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER
THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE
OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND
CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9.
Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),
excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief
in any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated
spacer
STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES
1.
Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or
documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein.
Acceptance of the EVM is expressly subject to the following terms and conditions.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2
Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software
License Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatment
by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any
way by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications or
instructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or as
mandated by government requirements. TI does not test all parameters of each EVM.
2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM,
or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the
warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to
repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall
be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
3
Regulatory Notices:
3.1 United States
3.1.1
Notice applicable to EVMs not FCC-Approved:
This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit
to determine whether to incorporate such items in a finished product and software developers to write software applications for
use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless
all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause
harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is
designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of
an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1
For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1
Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2
Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified
by TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required by Radio Law of
Japan to follow the instructions below with respect to EVMs:
1.
2.
3.
Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
SPACER
SPACER
SPACER
SPACER
SPACER
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて
いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの
措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社
東京都新宿区西新宿6丁目24番1号
西新宿三井ビル
3.3.3
Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ
い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
SPACER
4
EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1
User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2
EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.
5.
Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
6.
Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM (AND THE
DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY
THIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS AND
CONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY
OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD
PARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY
INVENTION, DISCOVERY OR IMPROVEMENT MADE, CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OF
THE EVM.
7.
USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS
LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,
EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY
HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS. THIS OBLIGATION
SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY
OTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
8.
Limitations on Damages and Liability:
8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE
TERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER, REGARDLESS OF WHETHER TI HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED
TO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS,
LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL
BE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATION
ARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS, OR ANY USE OF ANY TI EVM
PROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER
THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE
OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND
CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9.
Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),
excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief
in any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
spacer
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
UCD3138ALLCEVM150
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement