JVC DR-MX1S User Guide Manual Operating Instruction Pdf

JVC DR-MX1S User Guide Manual Operating Instruction Pdf
DVD / HDD VIDEO RECORDER &
VIDEO CASSETTE RECORDER
DR-MX1S
CABLE/DBS
TV
VHS
DVD
STANDBY/ON
DVD
TV/CBL/DBS
TV/
VIDEO
VHS
TIMER
HDD
DVD
TV VOLUME
CH
CANCEL
LIVE
AUX
MEMO/MARK
DUBBING
EDIT
PROGRAM
TV MUTING
TOP MENU
NAVIGATION
ENTER
MENU
RETURN
PREVIOUS
NEXT
SLOW
PLAY/SELECT
REC
STOP/ CLEAR
SLOW
PAUSE
JUMP
REC MODE
DISPLAY
ON SCREEN
SET UP
RAM/RW
REMAIN
VHS/HDD/DVD
STANDBY/ ON
SELECT
REC LINK
AUDIO
SUBTITLE
ANGLE
PROGRESSIVE
SCAN
S-VIDEO
HDD/DVD
VRS –
VIDEO (MONO)L–AUDIO–R
HDD –
DVD –
CH
DISPLAY
VHS TIMER
REC MODE
DV IN
F–1
LIVE CHECK
For Customer Use:
INSTRUCTIONS
Enter below the Model No. and
Serial No. which are located on the
rear of cabinet. Retain this
information for future reference.
Model No.
Serial No.
LPT0975-001C
Downloaded From DvDPlayer-Manual.com JVC Manuals
2
EN
SAFETY FIRST
Dear Customer,
Thank you for purchasing the JVC DVD / HDD video recorder &
video cassette recorder. Before use, please read the safety
information and precautions to ensure safe use of your new unit.
Cautions
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
CAUTION:
This unit should be used with AC 120Vd, 60Hz only.
To prevent electric shocks and fire hazards, DO NOT use any
other power source.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION:
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA
LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU
FOND.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
CAUTION:
A UNIT IS A CLASS 1 LASER PRODUCT. HOWEVER THIS
UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE
HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE
SURE TO OPERATE THE UNIT CORRECTLY AS
INSTRUCTED.
WHEN THIS UNIT IS PLUGGED INTO THE WALL OUTLET,
DO NOT PLACE YOUR EYES CLOSE TO THE OPENING OF
THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO
THE INSIDE OF THIS UNIT.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
CLASS 1 LASER PRODUCT
REPRODUCTION OF LABELS
WARNING LABEL INSIDE OF THE UNIT
Downloaded From DvDPlayer-Manual.com JVC Manuals
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides guidelines
for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
CAUTION:
Changes or modifications not approved by JVC could void user’s
authority to operate the equipment.
SAFETY FIRST
Important product safety
instructions
Electrical energy can perform many useful functions. But improper
use can result in potential electrical shock or fire hazards. This
product has been engineered and manufactured to assure your
personal safety. In order not to defeat the built-in safeguards,
observe the following basic rules for its installation, use and
servicing.
ATTENTION:
Follow and obey all warnings and instructions marked on your product
and its operating instructions. For your safety, please read all the safety
and operating instructions before you operate this product and keep
this booklet for future reference.
INSTALLATION
1. Grounding or Polarization
(A)Your product may be equipped with a polarized alternatingcurrent line plug (a plug having one blade wider than the other).
This plug will fit into the power outlet only one way. This is a
safety feature.
If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
(B)Your product may be equipped with a 3-wire grounding-type
plug, a plug having a third (grounding) pin. This plug will only fit
into a grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the grounding-type plug.
2. Power Sources
Operate your product only from the type of power source indicated
on the marking label. If you are not sure of the type of power
supply to your home, consult your product dealer or local power
company. If your product is intended to operate from battery
power, or other sources, refer to the operating instructions.
3. Overloading
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or
electric shock.
4. Power Cord Protection
Power supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
5. Ventilation
Slots and openings in the cabinet are provided for ventilation. To
ensure reliable operation of the product and to protect it from
overheating, these openings must not be blocked or covered.
● Do not block the openings by placing the product on a bed, sofa, rug
or other similar surface.
● Do not place the product in a built-in installation such as a bookcase
or rack unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
6. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
3
ANTENNA INSTALLATION INSTRUCTIONS
1. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product,
be sure the antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding connectors, location of
antenna discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
2. Lightning
For added protection for this product during a lightning storm, or
when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning
and power-line surges.
3. Power Lines
An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or
where it can fall into such power lines or circuits. When installing
an outside antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact with them
might be fatal.
4
EN
SAFETY FIRST
USE
SERVICING
1. Accessories
To avoid personal injury:
1. Servicing
If your product is not operating correctly or exhibits a marked
change in performance and you are unable to restore normal
operation by following the detailed procedure in its operating
instructions, do not attempt to service it yourself as opening or
removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
● Do not place this product on an unstable cart, stand, tripod, bracket,
or table. It may fall, causing serious injury to a child or adult, and
serious damage to the product.
● Use only with a cart, stand, tripod, bracket, or table recommended by
the manufacturer or sold with the product.
● Use a mounting accessory recommended by the manufacturer and
follow the manufacturer’s instructions for any mounting of the
product.
● Do not try to roll a cart with small casters across thresholds or deeppile carpets.
2. Product and Cart Combination
A product and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause the
product and cart combination to overturn.
3. Water and Moisture
Do not use this product near water—for
example, near a bath tub, wash bowl,
kitchen sink or laundry tub, in a wet
basement, or near a swimming pool and
the like.
4. Object and Liquid Entry
Never push objects of any kind into this product through openings
as they may touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid of any kind
on the product.
5. Attachments
Do not use attachments not recommended by the manufacturer of
this product as they may cause hazards.
6. Cleaning
Unplug this product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
7. Heat
The product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
2. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to restore
the product to its normal operation.
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance—
this indicates a need for service.
3. Replacement Parts
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or which have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric
shock or other hazards.
4. Safety Check
Upon completion of any service or repairs to this product, ask the
service technician to perform safety checks to determine that the
product is in safe operating condition.
HOW TO USE THIS INSTRUCTION MANUAL
● All major sections and subsections are listed in the Table Of
Contents on page 6. Use this when searching for information on a
specific procedure or feature.
● The Index on pages 12 – 15 illustrates the controls and connections
on the front and rear panel, the front display panel and the remote
control.
● The list of terms on page 97 lists frequently-used terms, and the
number of the page on which they are used or explained in the
manual.
● The 墌 mark signals a reference to another page for instructions or
related information.
● Operation buttons necessary for the various procedures are clearly
indicated through the use of illustrations at the beginning of each
major section.
BEFORE YOU INSTALL YOUR NEW UNIT . . .
. . . please read the sections/literature listed below.
● “Cautions” on page 2
● “Important product safety instructions” on pages 3 – 5
Downloaded From DvDPlayer-Manual.com JVC Manuals
SAFETY FIRST
Declaration of Conformity
Model Number:
DR-MX1S
Trade Name:
JVC
Responsible Party: JVC Americas Corp.
Address:
1700 Valley Road Wayne, N.J. 07470
Telephone Number: 973-317-5000
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
● Manufactured under licence from Dolby Laboratories. “Dolby” and
double-D symbol are trademarks of Dolby Laboratories.
● “DTS” and “DTS Digital Out” are trademarks of Digital Theater
Systems, Inc.
3
● VCR Plus+, C and PlusCode are registered trademarks of Gemstar
Development Corporation.
The VCR Plus+ system is manufactured under license from Gemstar
Development Corporation.
● DSSTM is an official trademark of DIRECTV, Inc., a unit of GM
Hughes Electronics. DISH NetworkTM is a trademark of Echostar
Communications Corporation.
● This product incorporates copyright protection technology that is
protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation and
other rights owners. Use of this copyright protection technology must
be authorized by Macrovision Corporation, and is intended for home
and other limited viewing users only unless otherwise authorized by
Macrovision Corporation. Reverse engineering or disassembly is
prohibited.
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
5
When the equipment is installed in a cabinet or a shelf, make sure
that it has sufficient space on all sides to allow for ventilation
(10 cm or more on both sides, on top and at the rear).
When discarding batteries, environmental problems must be
considered and the local rules or laws governing the disposal of
these batteries must be followed strictly.
Failure to heed the following precautions may result in
damage to the unit, remote control or disc/cassette.
1. DO NOT place the unit —
— in an environment prone to extreme temperatures or
humidity.
— in direct sunlight.
— in a dusty environment.
— in an environment where strong magnetic fields are
generated.
— on a surface that is unstable or subject to vibration.
2. DO NOT block the unit’s ventilation openings or holes.
(If the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to get out.)
3. DO NOT place heavy objects on the unit or remote control.
4. DO NOT place anything which might spill on top of the unit
or remote control.
(If water or liquid is allowed to enter this equipment, fire or
electric shock may be caused.)
5. DO NOT expose the apparatus to dripping or splashing.
6. DO NOT use this equipment in a bathroom or places with
water. Also DO NOT place any containers filled with water or
liquids (such as cosmetics or medicines, flower vases, potted
plants, cups, etc.) on top of this unit.
7. DO NOT place any naked flame sources, such as lighted
candles, on the apparatus.
8. AVOID violent shocks to the unit during transport.
MOISTURE CONDENSATION
Moisture in the air will condense on the unit when you move it from
a cold place to a warm place, or under extremely humid
conditions—just as water droplets form on the surface of a glass
filled with cold liquid. In conditions where condensation may occur,
disconnect the unit’s power plug from the wall and keep it
disconnected for a few hours to let the moisture dry, then turn on
the unit.
ATTENTION:
To mobile phone users:
Using a mobile phone in the vicinity of the unit may cause picture
vibration on the TV screen or change the screen to a blue back
display.
On placing the unit:
Some TVs or other appliances generate strong magnetic fields.
Do not place such appliances on top of the unit as it may cause
picture disturbance.
6
EN
CONTENTS
SAFETY FIRST
DISC INFORMATION
2
TIMER RECORDING ON VHS DECK
7
VCR Plus+® Timer Programming................................................. 60
Manual Timer Programming ........................................................ 61
About Discs ....................................................................................7
INDEX
12
INSTALLING YOUR NEW UNIT
19
Basic Connections .......................................................................19
INITIAL SETTINGS
20
Plug & Play Set ............................................................................20
Language .....................................................................................21
Clock Set......................................................................................22
Tuner Set .....................................................................................23
Cable Box and/or DBS Receiver Control Setting
(HDD & DVD Deck only) ..........................................................24
Monitor Set...................................................................................26
BASIC OPERATIONS ON DVD DECK
27
Basic Playback.............................................................................27
Playback Features .......................................................................28
Live Memory Playback .................................................................32
Using The On-screen Bar ............................................................36
Parental Lock ...............................................................................40
Basic Recording ...........................................................................41
Recording Features......................................................................42
BASIC OPERATIONS ON HDD DECK
44
Basic Recording ...........................................................................44
Recording Features......................................................................45
Basic Playback.............................................................................46
Playback Features .......................................................................46
Live Memory Playback .................................................................47
BASIC OPERATIONS ON VHS DECK
50
Basic Playback.............................................................................50
Playback Features .......................................................................51
Basic Recording ...........................................................................53
Recording Features......................................................................53
TIMER RECORDING ON HDD/DVD DECK
55
VCR Plus+ C3® Timer Programming ...........................................55
Manual Timer Programming.........................................................57
Automatic Satellite Program Recording
(HDD Deck Only)......................................................................59
Downloaded From DvDPlayer-Manual.com JVC Manuals
NAVIGATION ON HDD/DVD DECK
60
63
Library Database Navigation ....................................................... 63
Modify Original Information.......................................................... 64
Modify Play List Information ........................................................ 66
Modify Library Information ........................................................... 68
Playback With MP3/WMA/JPEG Navigation ............................... 69
EDITING
70
Dubbing ....................................................................................... 70
DV Dubbing (HDD & DVD Deck Only) ........................................ 74
Edit From A Camcorder ............................................................... 75
Edit To Or From Another Recorder ............................................. 76
Digital Audio Dubbing .................................................................. 77
REMOTE CONTROL
78
Remote Control Functions ........................................................... 78
SYSTEM CONNECTIONS
80
Connecting To A Dolby Digital Decoder Or An Amplifier
With Built-in DTS ..................................................................... 80
SUBSIDIARY SETTINGS
81
Mode Set (HDD & DVD Deck Only) ............................................ 81
Scan Mode Set ............................................................................ 83
Mode Set (VHS Deck Only) ......................................................... 84
Tray Lock (DVD Deck Only) ........................................................ 85
Changing VCR Plus+® Setting ..................................................... 86
Format A Disc (DVD Deck Only) ................................................. 87
Finalize A Disc (DVD Deck Only) ................................................ 88
TROUBLESHOOTING
89
SPECIFICATIONS
93
APPENDIX
94
LIST OF TERMS
97
WARRANTY (Only in U.S.A.)
98
FOR SERVICING (Only in U.S.A.)
100
DISC INFORMATION
About Discs
Recordable/Playable Discs
You can use discs with the following logos for recording and
playback.
EN
7
DVD-R/RW Discs
It is only possible to use DVD-R discs which conform with DVD-R
standard Version 2.0.
When a DVD-R/RW disc (Video mode) is finalized (墌 pg. 88), it
can be played back on a standard DVD player as a DVD VIDEO
disc.
When a DVD-RW disc (VR mode) is finalized (墌 pg. 88), it can be
played back on a standard DVD player compatible with the VR
mode of DVD-RW discs.
Before finalizing —
— it is possible to record on unrecorded areas of the disc, edit the
disc title and program titles, and delete programs.
DVD-RAM
12 cm: 4.7 GB/9.4 GB
8 cm: 1.4 GB/2.8 GB
Ver. 2.0/2x speed
Ver. 2.1/1x – 2x speed
DVD-RW
12 cm: 4.7 GB/9.4 GB
Ver. 1.1/1x – 2x speed (Video
mode/VR mode)
DVD-R
12 cm: 4.7 GB
8 cm: 1.4 GB
Ver. 2.0/1x – 4x speed (Video
mode)
● The above table is based on the information as of February 2004.
● Recording and playback may not be performed depending on the
characteristics and condition of the disc used, leading to
unsatisfactory results. Using discs manufactured by JVC is
recommended since they have been tested to be compatible with this
unit.
DVD-RAM Discs
It is only possible to use discs which conform with DVD-RAM
standard Version 2.0 or 2.1.
● It is impossible to record on DVD-RAM discs which do not conform to
this standard. If you use a disc formatted under a different standard
version, format it on this unit before use.
● It may not be possible to record, play back, edit or dub a DVD-RAM
disc even if it conforms to the standard if it was recorded or edited on
the devices from other manufacturers or on a PC, or if it has far too
many titles, or if there is very little available capacity remaining on the
disc.
● DVD-RAM discs recorded on this unit cannot be played back on an
incompatible DVD player.
● It is possible to record copy-once programs of digital broadcasts only
onto 4.7/9.4 GB DVD-RAM discs (2.8 GB DVD-RAM discs are not
compatible).
Downloaded From DvDPlayer-Manual.com JVC Manuals
● It is impossible to record or edit DVD-R/RW discs recorded on other
devices even if they have not been finalized.
● It is impossible to overwrite recorded areas of DVD-R discs.
● Available recording capacity does not increase even if a recorded
program is deleted from a DVD-R disc.
After finalizing —
After a DVD-R/RW disc (Video mode) has been finalized, it is
possible to play back the recorded programs (video and/or audio)
on a standard DVD video player as a DVD VIDEO disc.
● Edited titles are displayed as the
“DVD menu” in video mode.
● It is impossible to record, edit or
delete the data either in video
mode or in VR mode.
● Either in video mode or in VR
mode, although the disc can be
played back on DVD players from
other manufacturers, sometimes it
may not be possible to play back
depending on the disc and recording conditions.
● It is impossible to record on CD-R/RW or DVD-R discs used for
authoring.
● It is impossible to record onto DVD-R/RW (Video mode) discs
broadcasts that allow you to copy once. The copy once programs can
only be recorded onto DVD-RW discs formatted in VR mode.
NOTE:
The following may result if you play back a DVD-R disc recorded on
another unit.
● The disc does not play.
● A mosaic pattern (block noise) appears on the screen.
● Video or audio may be dropped out.
● The unit stops during playback.
8 EN DISC INFORMATION
Discs For Playback Only
Unplayable Discs
You can use discs with the following logos for playback only.
DVD VIDEO
Video CD/Super Video CD
The following types of discs cannot be played using this unit.
Do not attempt to play back any kind of disc that is damaged
(cracked, warped, or repaired with adhesive tape) or discs in
unusual shapes (heart-shaped, octagonal, or other forms). If such
discs are accidentally played back, it may cause noise that can
lead to speaker damage.
●
●
●
●
(example of region code
indications)
CD-ROM discs (including PHOTO-CD and CD-G)
Discs recorded in Packet Write (UDF) format
1.3-GB double density CDs (DDCD)
High density CDs (HDCD)
The following discs also cannot be played back.
● Discs of a region number other than “1”
● DVD-RAM (2.6 GB/5.2 GB)
● DVD-RAM (TYPE1)
Audio CD
CD-DA files
CD-RW
CD-DA/JPEG/
MP3 files
CD-R
CD-DA/JPEG/
MP3 files
CD-ROM
JPEG/MP3 files
● Playback may not be performed depending on the characteristics
and condition of the disc used.
● DTS Audio CDs can also be played back (An optional DTS decoder
is required).
● MP3 and JPEG discs can be played back on this unit only when they
have been recorded in the ISO9660 or Joliet format and finalized.
● JPEG files that can be played back on this unit must conform to JFIF/
Baseline process, and the maximum resolution of a JPEG file is
2,812 x 2,112 pixels.
● CD-R/RW discs recorded in music CD format need to be finalized to
play back on this unit.
● Operation and audio quality of this unit are not guaranteed for discs
that do not conform to the Compact Disc specification (CD-DA).
Before you play back a CD, check for the CD logo and read the notes
on the package to confirm that it conforms to the Compact Disc
specification.
● Depending on the intentions of the author of the software, recording
conditions of DVD discs and Video CD/SVCD discs may be
restricted. Since this unit plays back discs according to the intentions
of the author of the software as indicated on the disc, some functions
may not operate as commanded.
● When switching from the first layer to the second layer of doublelayered DVD VIDEO discs, the image and sound may be
momentarily distorted. This is not a malfunction.
● DVD-AUDIO discs compatible with DVD video players can be played.
● Super Audio CDs (SACD) compatible with conventional CD players
can be played.
Downloaded From DvDPlayer-Manual.com JVC Manuals
Region Number
The world is divided into 6 regions for DVD VIDEO discs.
DVD VIDEO discs are assigned a region number to indicate which
region they may be played back in. A disc cannot be played back
on this unit unless the region number of the disc matches that of
the unit. The region number for this unit is “1”. Only discs whose
region number includes “1” or “ALL” can be played back such as
shown below.
Examples of DVD VIDEO labels which can be played back
using this unit.
Marks of discs in this instruction manual
Allows operation with a
DVD-RAM disc.
Allows operation with a
Video CD/Super Video
CD (SVCD) disc.
Allows operation with a
DVD-R disc.
Allows operation with
an Audio CD disc.
Allows operation with a
DVD-RW disc.
Allows operation with a
disc including MP3
files.
Allows operation with a
DVD VIDEO disc.
Allows operation with a
disc including JPEG
files.
DISC INFORMATION
Recording Medium And Format
DVD-RAM
● Recording and erasing can be performed as many times as possible
on a disc.
● Editing can be performed after recording, such as deleting unwanted
parts.
● While recording, it is possible not only to start playback of a program
currently being recorded, but also to watch another program
previously recorded.
EN
9
Audio CD/Video CD/SVCD
Typically, Audio CD discs are divided into separate tracks each
containing one song. Each track is assigned a number. For
example, the third track is Track 3. The same is true for Video CD/
SVCD discs.
However, some discs are not divided into tracks.
Audio CD or Video CD/SVCD
Track 1
Track 2
Track 3
Track 4
DVD-RW (VR mode)
● Recording and erasing can be performed as many times as possible
on a disc.
● Editing can be performed after recording, such as deleting unwanted
parts.
DVD-RW (Video mode)
● Can be played back on other DVD players.
● New recording can be performed by erasing all the data on a disc
once played back.
JPEG/MP3 Disc (CD-R/RW/ROM)
MP3/JPEG files put in directories nested in several levels on a disc
will be organized as if they were put in single level directories
(groups) by the MP3/JPEG Navigation of this unit. (墌 pg. 69)
File structure of a disc before starting the MP3/JPEG
Navigation
DVD-R
● Can be played back on other DVD players.
● Suitable when keeping a recorded disc for a long time.
File Structure Of Discs
DVD VIDEO
Typically, DVD VIDEO discs are made up of larger units called
“titles”. Each title has a number (title number) that can be used to
select desired titles. Titles are further divided into units called
“chapters”. Each chapter has a number (chapter number) that can
also be used to select desired chapters. Note that some discs are
not divided into titles and chapters.
When you record a program on a DVD-RAM/RW (VR mode)
disc
A single recording session results in a single title (a single
chapter). However, chapter marks are automatically inserted when
recording is paused, or audio changes from monaural to stereo
due to commercial breaks, etc. It is also possible to insert chapter
marks at desired locations during playback. (墌 pg. 29)
Directory
MP3 file
JPEG file
File structure of the disc after starting the MP3/JPEG
Navigation
Files are automatically grouped as follows and displayed on the
MP3/JPEG Navigation screen. Data is displayed in the
alphabetical order of file name. Files are grouped based on roots.
When you record a program on a DVD-R/RW (Video mode)
disc
A single recording session results in a single title (a single
chapter). However, chapter marks are automatically inserted when
recording is paused, or audio changes due to commercial breaks,
etc. It is also possible to insert chapter marks at desired locations
during either recording or playback. Once the disc has been
finalized, these chapter marks are deleted and new chapter marks
are assigned automatically approximately every 5 minutes.
DVD-RAM, DVD-RW, DVD-R or DVD VIDEO disc
Title 1
Chapter 1
Chapter 2
Title 2
Chapter 3
Chapter 1
Chapter 2
Chapter 3
● In Video mode, even before finalizing, it is impossible to perform
editing operations other than changing the disc name and/or title
names and deleting programs and/or titles.
● After finalizing, it is impossible to perform editing operations.
● This unit can recognize up to 9 hierarchies including directories and
files.
Also, it can recognize up to 250 files in each group, and up to 99
groups on a disc.
NOTES:
● Video CD/SVCD discs that support Playback Control (PBC)
The contents of a disc are recorded into several hierarchies, and played
back according to the instructions on the screen while navigating through
the hierarchies. It is also possible to playback recorded tracks
consecutively without activating the PBC function even when playing a
PBC-compatible disc. (墌 pg. 31)
● Regarding the contents recorded on discs
Some files may not be played back depending on the file types and other
factors.
Downloaded From DvDPlayer-Manual.com JVC Manuals
10 EN DISC INFORMATION
DVD VIDEO Marks
Placing A Disc
Sometimes marks are printed on a DVD disc and/or on its
packaging to indicate information regarding the contents and
functions of the disc. Check the marks indicating the contents and
functions of the disc. Note, however, that in some cases a disc
may not include a mark even for a function it supports.
Opening the disc tray
Press x to open the disc tray.
Marks related to video
Number of subtitles
Number of angles
VHS/HDD/DVD
SELECT
DVD –
DISPLAY
Recorded under the
standard 4:3 aspect
ratio
Screen includes black
bands at the top and
the bottom of image
which has a standard
4:3 aspect ratio (letter
box)
Video playback is in Wide video mode (16:9) on
wide televisions, but in letter box on televisions
with standard 4:3 aspect ratio.
Video playback is in Wide video mode (16:9) on
wide televisions, but pan and scan is used on
televisions with standard 4:3 aspect ratio (either
the left or right side of the image is cut-out).
VHS TIMER
REC MODE
DV IN
● Pressing the button again closes the disc tray.
● Use the button to open and close the disc tray.
● Do not block the disc tray with your hand while it is opening or closing
as this may result in hardware failure.
● Do not place unplayable discs or any object other than a disc on the
disc tray.
● Do not press down strongly on the disc tray or place any heavy
objects on it.
Discs without cartridges
Marks related to audio
Number of audio tracks
Dolby Digital mark
It has been developed by Dolby Laboratories as
a digital surround system.
DTS (Digital Theater Systems)
You can enjoy DTS audio if you connect an
amplifier with a built-in DTS decoder to the
DIGITAL OUT connector of the unit.
Disc tray
Place the disc on the disc tray with the label side facing up. Since
disc size changes depending on the disc to be played back, be
sure to correctly align the disc with the grooves for its size. If the
disc is not in its groove, it may be scratched or otherwise
damaged. To insert an 8 cm disc, place it according to the inner
groove.
DVD-RAM discs contained in cartridges
Double-sided discs:
Remove the disc from the cartridge. Align the disc with the grooves
on the disc tray as shown in the illustration and insert with the side
you wish to play back or record facing down. If you insert the disc
with “Side A” facing down, programs are recorded on the side A.
Single-sided discs:
Remove the disc from the cartridge. Align the disc with the grooves
on the disc tray as shown in the illustration and insert with the label
side facing up.
Downloaded From DvDPlayer-Manual.com JVC Manuals
DISC INFORMATION
Care And Handling Of Discs
How to handle discs
When handling a disc, do not
touch the surface of the disc.
Since discs are made of
plastic, they are easily
damaged. If a disc gets dirty,
dusty, scratched or warped, the
images and sound will not be
picked up correctly, and such a
disc may cause the unit to malfunction.
Label side
Do not damage the label side, stick paper to or use any adhesives
on its surface.
Recording side
Make sure that discs are not scratched and dirty on the recording
side before use. Scratches and dirt on the recording side of a disc
may hinder proper playback and recording. Also be careful that a
DVD-RAM disc may get scratched or dirt when removed from
cartridge then put back in after use.
Storage
Make sure that discs are kept in their cases. If discs are piled on
top of one another without their protective cases, they can be
damaged. Do not put discs in a location where they may be
exposed to direct sunlight, or in a place where the humidity or
temperature is high. Avoid leaving discs in your car!
Maintenance of discs
If there are fingerprints or other dirt adhering
to a disc, wipe with a soft dry cloth, moving
from the centre outwards.
If a disc is difficult to clean, wipe with a cloth
moistened with water. Never use record
cleaners, petrol, alcohol or any anti-static
agents.
CAUTION:
Sometimes during playback, noise may appear or images may
be garbled. This is sometimes due to the disc. (It may not be up
to industry standards.)
These symptoms are caused by the discs, not by the
malfunction of the unit.
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
11
12 EN INDEX
Front View
A
B
C
D
VHS –
HDD –
E
F G H IJ
VHS/HDD/DVD
STANDBY/ ON
SELECT
S-VIDEO
HDD/DVD
VIDEO (MONO)L–AUDIO–R
DVD –
CH
DISPLAY
VHS TIMER
REC MODE
F–1
KL
M
DV IN
HDD/DVD
N
A Eject Button (x) (VHS) 墌 pg. 50
B Cassette Loading Slot
C VHS Lamp (VHS) 墌 pg. 50
VHS Recording Lamp (7) 墌 pg. 53
D HDD Lamp (HDD) 墌 pg. 21, 44
HDD Recording Lamp (7) 墌 pg. 44
E Open/Close Button (x) 墌 pg. 10
F VHS/HDD/DVD Select Button (VHS/HDD/DVD
SELECT) 墌 pg. 27, 44, 50
O
● This button will not function during navigation mode or set up
mode.
G Stop Button (8) 墌 pg. 27, 46
H Disc Tray
I Reverse Search Button (3) (HDD &DVD deck)
墌 pg. 28, 35
Rewind Button (3) (VHS deck) 墌 pg. 50, 51
J Forward Search Button (5) (HDD &DVD deck)
墌 pg. 28, 35
Fast Forward Button (5) (VHS deck) 墌 pg. 50, 51
K STANDBY/ON Button (1)
P Q
R S T VW X
U
L S-video Input Connector [S-VIDEO] (HDD & DVD deck)
墌 pg. 75
M Video/Audio Input Connectors
[VIDEO/AUDIO ((MONO) L/R)] 墌 pg. 75
N Channel Buttons (CH +/–) 墌 pg. 41, 44, 52, 53
O Front Display Panel 墌 pg. 14
P DVD Lamp (DVD) 墌 pg. 21, 27
DVD Recording Lamp (7) 墌 pg. 41
Q Infrared Beam Receiving Window
R Display Button (DISPLAY) 墌 pg. 30, 42
S VHS Timer Button (VHS TIMER ) 墌 pg. 60
T Recording Mode Button (REC MODE) 墌 pg. 41, 44, 53
U Play Button (4) 墌 pg. 27, 46
V Record Button (7) 墌 pg. 41, 44
W Pause Button (9) 墌 pg. 27, 46
X DV Input connector [DV IN (i*)] (HDD & DVD deck only)
墌 pg. 74
* i (i.Link) refers to the IEEE1394-1995 industry specification and
extensions thereof. The i logo is used for products compliant with the
i.Link standard.
To access covered connectors, pull
and open the connector cover.
Downloaded From DvDPlayer-Manual.com JVC Manuals
INDEX
EN
13
Rear View
A B
D E F G
C
HDD/DVD
DIGITAL
PCM/
AUDIO OUT
STREAM
S-VIDEO
H
HDD/DVD
S-VIDEO
COMPONENT
VIDEO OUT
HDD/DVD
VIDEO
Y
OPTICAL
PB
COAXIAL
PR
VIDEO
VIDEO
L
AUDIO
AUDIO
AUDIO
R
R
R
INPUT L-1
D Digital Audio Output Connectors
[DIGITAL AUDIO OUT (OPTICAL/COAXIAL)] (HDD &
DVD deck only) 墌 pg. 77, 80
Downloaded From DvDPlayer-Manual.com JVC Manuals
L
CABLE
BOX
OUTPUT
OUT
ANT. LOOP OUT
TV OUT
VHF/UHF
I
● This prevents the temperature from rising inside the unit.
Do not remove it.
● Install the unit so as not to block the area around the fan.
● The cooling fan on the rear of the unit may be activated even if
the unit is turned off in the following cases;
— In the Automatic Satellite Program Recording standby mode
(墌 pg. 59)
— when “AUTO CLOCK” is set to “ON” (墌 pg. 22)
(Set “AUTO CLOCK” to “OFF” if you mind the noise of the fan.)
VHS/HDD
/DVD
L
OUTPUT
HDD/DVD
A Region Number Label 墌 pg. 8
B AC Power Cord 墌 pg. 19
C Cooling Fan
VHS
IN
JK
L
E Component Video Output Connectors [COMPONENT
VIDEO OUT (Y/PB/PR)] 墌 pg. 19
● This component video output enables you to watch the images
on the VHS deck in Progressive scan mode, refer to “VHS
Progressive Scan” (墌 pg. 52).
F S-video/Video/Audio Output Connectors [S-VIDEO/
VIDEO/AUDIO OUTPUT] (HDD & DVD deck only)
墌 pg. 19
G S-video Input Connectors [S-VIDEO INPUT] (HDD &
DVD deck only) 墌 pg. 76
H Antenna Input Connectors [VHF/UHF IN] 墌 pg. 19
I Video/Audio Input Connectors [VIDEO/AUDIO INPUT
L1] 墌 pg. 76
J Video/Audio Output Connectors [VIDEO/AUDIO
OUTPUT] 墌 pg. 76
K Cable Box Control Connector [CABLE BOX] 墌 pg. 24
L Antenna Output Connectors [VHF/UHF OUT] 墌 pg. 19
14 EN INDEX
Front Display Panel
A
B
C
DE F
G
H
I
J
K
L
LPCM
FR
XP SP LP EP
VR +-RW VCD
VHS HDD DVD -RAM
N O
M
P
) 墌 pg. 42, 45, 53
Lights when VIDEO mode is selected by pressing TV/VIDEO. Lights
off when TV mode is selected.
A Video Indicator (
B Disc Type Indicator
R
S
T
H Channel/Recording Mode Indicator
Indicates the channel received. Or the recording mode (SP, EP) of
the VHS deck.
I Track/Chapter Indicator (TRK/CHAP)
When a disc is loaded, the type of the disc is indicated.
Disc Status Indicator
When a disc is running, the disc marks rotate.
During High-Speed Search: Rotate faster than normal playback.
During Slow Motion:
Rotate slower than normal playback.
While recording:
Inner red ring lights in the same way
as normal playback. During Instant
Timer Recording (ITR), inner red ring
slowly blinks.
While paused:
Disc marks blink when either
recording or playing back.
While stopped:
Disc marks all light.
While resume stopped:
Disc marks all blink.
While the disc tray opened:
Disc marks all light out.
No disc on the disc tray:
Disc marks all light out.
VR Mode Indicator (VR) 墌 pg. 87
Lights when a DVD-RW disc is formatted in VR mode.
C Linear PCM Indicator (LPCM)
Lights when “XP MODE REC AUDIO” is set to “LINEAR PCM”
(墌 pg. 82) for recording with HDD, DVD-RAM, DVD-R and
DVD-RW discs, and when Linear PCM audio is played.
D Cassette Loaded Mark (
)
Indicates the present of a cassette in the VHS deck.
Lights when a cassette is loaded into the VHS deck. Blinks when
the end of the tape has been reached during timer recording, or
when the unit is in timer recording standby mode with a cassette
without record safety tab inserted.
E VHS Timer Indicator (
Q
)
Lights when the VHS deck is in the timer recording standby mode or
when timer recording is in progress.
Blinks rapidly when VHS TIMER is pressed under the following
conditions:
● Clock is not set.
● Timer programming has not been set.
● Cassette is not loaded.
● Timer recording standby mode with a cassette without safety tab
inserted.
● Tape end is reached during time recording.
F Recording Mode Indicator (XP/SP/LP/EP/FR) 墌 pg. 41
Blinks when recording mode is being set.
While “FR” is blinking, the left 3 digits of the Multi Display (P Q)
indicate setting values ranging from “60” to “480”. After the value
has been set, only “FR” lights.
G Group/Title Indicator (GRP/TITLE)
“GRP” or “TITLE” lights depending on a disc loaded while the left 2
digits of the Multi Display (P) indicate the numbers explained
below.
“GRP”:
Total number of groups or group number being played
back are displayed on the Multi Display.
“TITLE”: Total number of titles or title number being played back
are displayed on the Multi Display.
Downloaded From DvDPlayer-Manual.com JVC Manuals
“TRK” or “CHAP” lights depending on a disc loaded while the 3rd
and 4th digits from the left of the Multi Display (Q) indicate the
numbers explained below.
“TRK”:
Total number of tracks or track number being played
back are displayed on the Multi Display.
“CHAP”: Chapter number being played back are displayed on the
Multi Display.
J Simulated Surround Effect Indicator (3D) 墌 pg. 38
Lights when a simulated surround effect is set to “3D-ON” on the
on-screen bar.
K Random/Program Playback Mode Indicator (RND/
PRGM) 墌 pg. 39
“RND”:
Lights when Random Playback mode is set.
“PRGM”: Lights when Program Playback mode is set.
L Repeat Mode Indicator (
/1/A–B) 墌 pg. 37
Select Repeat Playback mode on the on-screen bar.
“
”:
Whole disc is played back repeatedly.
“
1”:
A single title/chapter/track is played back repeatedly.
“
A–B”: The selected part (A–B) is played back repeatedly.
No display: Repeat Playback mode is off.
M VHS Indicator 墌 pg. 42
Lights when VHS mode has been selected, during recording or
when tapes recorded in VHS format are played back.
N Video Output Indicator (
) 墌 pg. 83
No display: Indicates that interlace mode is engaged.
:
Indicates that progressive mode is engaged.
(Example)
lights when video output mode is in progressive
mode.
O Automatic Satellite Program Recording Indicator
墌 pg. 59
Lights when the HDD deck is in the Auto Satellite Program
Recording standby mode.
P Group/Title Number Display
Q Track/Chapter Number Display
R Remaining Time/Elapsed Time Indicator 墌 pg. 30, 42
Lights when remaining time of HDD, DVD-RAM, DVD-R and
DVD-RW discs is displayed, and lights out when elapsed time is
displayed.
The right 6 digits of the Multi Display (S) indicate elapsed or
remaining time of each track.
No display: Indicates elapsed time of the disc.
Displayed: Indicates remaining time of the disc.
S Remaining Time/Elapsed Time Display 墌 pg. 30, 42
T Multi Display
Displays clock, received channel, elapsed time, and remaining time.
Also displays status of the unit (NO DISC/OPEN/CLOSE/
READING).
INDEX
Remote Control
CABLE/DBS
TV
A
B
C
D
VHS
DVD
STANDBY/ON
DVD
TV/CBL/DBS
TV/
VIDEO
VHS
TIMER
HDD
DVD
TV VOLUME
U
V
W
X
Y
E
CH
F
G
H
I
J
K
CANCEL
AUX
MEMO/MARK
LIVE
DUBBING
EDIT
Z
PROGRAM
TV MUTING
TOP MENU
NAVIGATION
ENTER
L
MENU
RETURN
M
N
O
P
Q
R
PREVIOUS
NEXT
SLOW
PLAY/SELECT
REC
STOP/ CLEAR
SLOW
PAUSE
JUMP
REC MODE
DISPLAY
ON SCREEN
SET UP
REMAIN
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
REC LINK
p
AUDIO
SUBTITLE
S
T
ANGLE
PROGRESSIVE
SCAN
LIVE CHECK
q
r
A TV/VIDEO Button 墌 pg. 42, 45, 53
B VHS Timer Button (VHS TIMER) 墌 pg. 60
C VHS Button* 墌 pg. 50
* This button will not function during navigation mode or set up mode.
D HDD Button* 墌 pg. 44
* This button will not function during navigation mode or set up mode.
Number Keys 墌 pg. 23, 41, 44
Cancel Button (& (CANCEL)) 墌 pg. 39
Auxiliary Button (AUX)
Live Button (LIVE) 墌 pg. 35, 48
Dubbing Button (DUBBING) 墌 pg. 70
TV Muting Button (TV MUTING) 墌 pg. 78
J Top Menu Button (TOP MENU) 墌 pg. 28
K rt w e Buttons 墌 pg. 21
L Menu Button (MENU) 墌 pg. 28
M Reverse Skip Button (2) 墌 pg. 28, 48, 49
Previous Button (PREVIOUS) 墌 pg. 31
N Reverse Search Button (3) (HDD & DVD deck)
墌 pg. 28, 48
Rewind Button (3) (VHS deck) 墌 pg. 50
Reverse Slow Button (SLOW –) 墌 pg. 29
O Record Button (7) 墌 pg. 41, 44
Downloaded From DvDPlayer-Manual.com JVC Manuals
E
F
G
H
I
EN
15
P Jump Button (JUMP +/–) 墌 pg. 49
Q Recording Mode Button (REC MODE) 墌 pg. 41, 44
Remain Button (REMAIN) 墌 pg. 30, 42
R Display Button (DISPLAY) 墌 pg. 30, 42
S Audio Button (AUDIO) 墌 pg. 31
T Subtitle Button (SUBTITLE) 墌 pg. 30
U TV/CABLE/DBS/DVD switch 墌 pg. 21
V DVD STANDBY/ON Button (DVD 1)
W TV/CBL/DBS STANDBY/ON Button (TV/CBL/DBS 1)
墌 pg. 78
X DVD Button* 墌 pg. 27
* This button will not function during navigation mode or set up mode.
Y TV Volume Buttons (TV VOLUME +/–) 墌 pg. 78
Z Channel Buttons (CH +/–) 墌 pg. 41, 78
a Memo Button (MEMO) 墌 pg. 64, 67
Mark Button (MARK) 墌 pg. 29
b Programming Button (PROGRAM) 墌 pg. 55, 57, 58
c Edit Button (EDIT) 墌 pg. 64
d Navigation Button (NAVIGATION) 墌 pg. 63
e Enter Button (ENTER) 墌 pg. 21
f Return Button (RETURN) 墌 pg. 31, 37, 55
g Forward Skip Button (6) 墌 pg. 28, 48, 49
Next Button (NEXT) 墌 pg. 31
h Forward Search Button (5) (HDD & DVD deck)
墌 pg. 28, 48
Fast Forward Button (5) (VHS deck) 墌 pg. 50
Forward Slow Button (SLOW +) 墌 pg. 29
i Play Button (4) 墌 pg. 27, 46
Select Button (SELECT) 墌 pg. 69
j Pause Button (9) 墌 pg. 27, 46
k Stop Button (8) 墌 pg. 27, 46
Clear Button (CLEAR) 墌 pg. 39
l Skip Search Button (
) 墌 pg. 29, 48
m Set Up Button (SET UP) 墌 pg. 21
n One Touch Replay Button (
) 墌 pg. 48
o On-Screen Button (ON SCREEN) 墌 pg. 16, 36
p Automatic Satellite Program Recording Button (REC
LINK) 墌 pg. 59
q Progressive Scan Button (PROGRESSIVE SCAN)
墌 pg. 83
r Angle Button (ANGLE) (DVD deck only) 墌 pg. 30
Live Check Button (LIVE CHECK) 墌 pg. 35, 48
How To Use
Before use, insert two AA size batteries into the remote control
with the polarity ( and ) matched correctly as indicated on
the battery compartment or on the lid.
The remote control can operate most of your unit’s functions, as
well as basic functions of TV sets of JVC and other brands.
(墌 pg. 78)
● Point the remote control toward the receiving window.
● The maximum operating distance of the remote control is about
8 m.
NOTE:
If the remote control doesn’t work properly, remove its batteries, wait
a short time, replace the batteries and then try again.
16 EN INDEX
On-Screen Display (DVD deck)
When pressing REC MODE
(Appears for eight seconds.)
When “SUPERIMPOSE” is set to “AUTO” and ON SCREEN on the
remote control is pressed, various operational indicators appear on
the TV screen. To clear the operational indicators, press ON
SCREEN twice.
RAM
FR360
7: 00
10: 00
20: 00
28: 00
36: 00
When playing back a recorded title
TITLE99 CHAPTER999 T. REMAIN6:59:59
XP
01:16:48
12
FISHING WORLD
A
B
C
D
E
F
G
H
I
J
K
Playback title number
Playback chapter number
Disc remaining time
Current status (playback)
Audio mode
Current received (recording) channel position number
(On playback background)
Bar meter
Name of title (or play list) currently being played back
Current playback point
Recorded mode
Live Memory mode (recording)
TITLE99 CHAPTER999 T. REMAIN6:59:59
11:35 AM
ITR
2 : 30
A Recording time for Instant Timer Recording (ITR) mode
12
FR360
A
B
C
D
Disc type
Current recording speed
Remaining disc time for each recording speed
Recording speed
When pressing 7 during recording
When recording
RAM
A
B
C
D
XP
SP
LP
EP
FR480
Recording point
Current status (recording)
Current time
Recording channel number
Downloaded From DvDPlayer-Manual.com JVC Manuals
INDEX
On-Screen Display (HDD deck)
When “SUPERIMPOSE” is set to “AUTO” and ON SCREEN on the
remote control is pressed, various operational indicators appear on
the TV screen. To clear the operational indicators, press ON
SCREEN twice.
FR360
1:00
11:00
12:00
1:00
FR360
11:35AM
12
11:33AM
STEREO
A Live Memory Recording point
B Live Memory Recording mode
When playing back a recorded title
0:00
EN
When recording
2:00
01:16:48
12
When pressing REC MODE
(Appears for eight seconds.)
STEREO
004 FISHING WORLD
FR360
A
B
C
D
E
F
G
H
I
J
K
Title start
Current playback point
Title end
Time scale (This title is an hour and a half long.)
Play mode
Elapsed playing time
Current received (recording) channel position number
(On playback background)
Recorded title (or play list) number currently being played back
Name of title currently being played back
Audio mode
Live Memory mode (recording)
When watching a program on air
7: 00
10: 00
20: 00
28: 00
36: 00
A
B
C
D
XP
SP
LP
EP
FR480
HDD capacity graph
Current recording speed
Remaining HDD time for each recording speed
Recording speed
When pressing 7 during recording
ITR
2 : 30
A Recording time for Instant Timer Recording (ITR) mode
11:00
12:00
1:00
11:35AM
12
STEREO
ON AIR
A Possible start point from where Live Memory Playback can be
performed
B Possible start point from where Live Memory Recording can be
performed
(Received channel has changed at this point.)
C Currently viewed point
D Time scale
E Current time
F Current received channel position number
When using Live Memory playback
11:00
A
B
C
D
E
F
G
H
12:00
1:00
11:35AM
12
11:35AM
STEREO
Time scale for Temporary Recording
Current Temporary Recording point
Current time
Current playback channel position number
Time scale for Live Memory Playback
Current playback point
Live Memory playback mode
Current playback time
Downloaded From DvDPlayer-Manual.com JVC Manuals
17
18 EN INDEX
On-Screen Display (DV Dubbing)
On-Screen Display (VHS deck)
When “SUPERIMPOSE” is set to “AUTO” and ON SCREEN on the
remote control is pressed, various operational indicators appear on
the TV screen. To clear the operational indicators, press ON
SCREEN again.
When capturing images from the external DV
equipment
HDD
A
B
C
D
E
F
G
H
I
J
K
0:00
1:00
FR360
00:00:00. 00
12bit
DV
JVC
2:00
GR-DV3500
DV
00:00:00. 00
L - R
L
SOUND1
GR-DV3500
K
J
I
H
Recording speed
HDD capacity graph
HDD time counter
Recording time scale
HDD mode
Remote control mode
Connected DV equipment mode
Connected DV equipment model information
Input channel
Sound mode
Sound input bit-rate*
G
* Indicates the sound bit-rate of the connected DV equipment
L Connected DV equipment information*
* Maker name and model name, etc. may not appear depending on the
connected equipment.
DV
1
C
D
E
F
A Operation Mode Indicators
B Recording Mode (SP/EP)
C Tape Position Indicator
The tape position indicator
appears on the TV screen when
you press 3 or 5 from the
Stop mode or perform an Index
Search. (墌 pg. 51) The position
of “ ” in relation to “0”
(Beginning) or “+” (End) shows
you where you are on the tape.
M Time counter for the connected DV equipment
N Sound monitor mode
DV
A
B
2
NOTE:
O Remote control switch
P Auto capture button
Q Sound monitor switch
Depending on the type of tape
Beginning
being used, the tape position
indicator may not appear correctly.
179 : 59 : 59
R Elapsed recording time
Downloaded From DvDPlayer-Manual.com JVC Manuals
End
Index number 墌 pg. 51
Tape Remaining Time Indicator 墌 pg. 54
Counter Display
Audio Mode Display 墌 pg. 52
SAP Indicator 墌 pg. 54
Stereo Program Indicator 墌 pg. 54
Day/Clock Display
Channel Position Number/Auxiliary Input Indicator (L-1
or F-1)
L “Cassette Loaded” Mark
D
E
F
G
H
I
J
K
INSTALLING YOUR NEW UNIT
Basic Connections
Coaxial cable
8 S-Video Connection (HDD & DVD deck only)
To connect to TV’s S-VIDEO input and AUDIO input
connectors —
A Perform A – B in “RF Connection”.
B Connect the unit’s [S-VIDEO OUTPUT] connector to the TV’s
S-VIDEO input connector.
C Connect the unit’s [AUDIO OUTPUT] connectors to the TV’s
AUDIO input connectors.
Flat feeder
Matching transformer
(not supplied)
RF cable ( not supplied)
Antenna splitter
(not supplied)
RF cable
(not
supplied)
RF cable (not supplied)
AC power cord
To [VHF/
UHF IN]
(VHS)
To [VHF/UHF IN]
(HDD/DVD)
.
Back of unit
To
[COMPONENT
VIDEO OUT
(Y/PB/PR)]
To [S-VIDEO
OUTPUT]
To [TV
OUT]
To [AUDIO/
VIDEO
OUTPUT]
Audio/video
cable
(supplied)
S-Video cable
(not supplied)
Component
video cable
(not supplied)
To audio/
video input
connectors
To S-VIDEO
input connector
● You can obtain high-quality S-VHS pictures.
● If your TV is not stereo-capable, use the unit’s [AUDIO OUTPUT]
connectors to connect to an audio amplifier for Hi-Fi stereo sound
reproduction.
8 Component Video Connection
To connect to TV’s component video input connectors —
A Perform A – B in “RF Connection”.
B Connect the unit’s [COMPONENT VIDEO OUT (Y/PB/PR)]
connectors to the TV’s component video input connectors.
C Connect the unit’s [AUDIO OUTPUT] connectors to the TV’s
AUDIO input connectors.
● You can obtain high-quality component video pictures.
● If your TV is not stereo-capable, use the unit’s [AUDIO OUTPUT]
connectors to connect to an audio amplifier for Hi-Fi stereo sound
reproduction.
● By using the component video connection, you can view the images
in the progressive mode. For switching to the progressive mode, refer
to “Scan Mode Set” (墌 pg. 83).
● You can also watch the images on the VHS deck in Progressive scan
mode via the component video output, refer to “VHS Progressive
Scan” (墌 pg. 52).
4 Plug the end of the AC power cord into an AC outlet. This unit
RF cable
(supplied)
TV
To component video
input connectors
19
8 AV Connection
To connect to a TV with AV input connectors —
A Perform A – B in “RF Connection”.
B Connect the supplied audio/video cable between the [AUDIO/
VIDEO OUTPUT] connectors on the rear panel of the unit and
the TV’s audio/video input connectors.
Antenna or Cable
AC outlet
EN
● Connect the unit’s [ANT. LOOP OUT] connector to the antenna input
connector on another video unit.
To 75 ohm
terminal
It’s essential that your unit be properly connected.
THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO
OPERATION CAN BE PERFORMED.
1 Make sure the package contains all of the accessories listed in
“SPECIFICATIONS” on page 93.
2 Place the unit on a stable, horizontal surface.
3 Connect the unit to a TV depending on the TV and cables you
use.
8 RF Connection
To connect to a TV with NO AV input connectors —
A Disconnect the TV antenna from the TV.
B Connect the TV antenna cable to the [VHF/UHF IN] connectors
on the rear panel of the unit via antenna splitter.
C Connect the supplied RF cable between the [TV OUT]
connector on the rear panel of the unit and the TV’s antenna
terminal.
NOTES:
● If you do not use antenna splitter, connect the TV antenna cable to
[VHF/UHF IN] (HDD/DVD) connector. However, it is not possible to
record the TV program on the VCR deck.
Downloaded From DvDPlayer-Manual.com JVC Manuals
performs Plug & Play Set automatically. (墌 pg. 20)
● The clock and tuner channels will automatically be set when the
antenna is connected and when the AC power cord is first connected
to an AC outlet. (If “AUTO” and the channel indicator are displayed
on the front display panel before the unit is powered on, the clock and
tuner channels are being set automatically. Wait for the time to be
displayed on the front display panel before turning on the unit.)
● “LOADING” blinks on the front display panel when the AC plug of the
AC power cord is connected into an AC outlet and it takes
approximately 50 seconds for the unit to be turned on. This is not a
malfunction.
5 Set the video channel. The video channel is the channel on
which you can watch the picture from the unit on the TV when only
using RF connection.
With RF Connection
Set the video channel to “3 CH” or “4 CH”. To set the video
channel, perform steps A – C below:
● The video channel is preset to “3 CH”. Set to “4 CH” if the Channel 3
is used for broadcasting in your area.
With AV Connection
Set the video channel to “– CH” (off). To set the video channel,
perform steps A – C below:
With S-Video/Component Video Connection (HDD & DVD deck
only)
Set the video channel to “– CH” (off). To set the video channel,
perform steps A – C below:
How To Set The Video Channel
A Make sure that there is no cassette in the unit.
B Press 1 to turn off the unit, then press 8 on the unit for more
than 5 seconds. “3 CH” appears on the front display panel.
C Press CH +/– on the remote control to select “3 CH”, “4 CH” or
“– CH” (off), then press ENTER.
20
EN
INITIAL SETTINGS
1 Connect the antenna cable to the unit. (墌 pg. 19) Then connect
Plug & Play Set
the AC power cord to an AC outlet. Do not turn on the unit.
The clock and tuner channels will be set automatically.
Auto Clock Set/Auto Tuner Set
This unit sets the clock and tuner channels automatically when AC
power cord is first connected to an AC outlet. The antenna cable
must be connected for the Plug & Play setting.
The time and date can be set automatically by the clock setting
data transmitted from one of the regular TV broadcast channels.
We call this TV channel the “host channel” and it is a PBS channel
in your area.
ATTENTION:
● If you use a cable box, Plug&Play will not function; set the clock
and tuner channels separately. (墌 pg. 22 – 23)
● Depending on areas or reception conditions, the unit may not
receive the Auto clock setting data from the PBS channel. If this
function is taking a considerable amount of time, it may be
necessary to perform the Semiauto or Manual Clock Set
procedure.
● “LOADING” blinks on the front display panel when the AC plug of the
AC power cord is connected into an AC outlet and it takes
approximately 50 seconds for the unit to be turned on. This is not a
malfunction.
NOTES:
● Auto Clock Set is performed first.
“AUTO” blinks on the front display panel during Auto Clock Set.
● Auto Channel Set is performed next. Auto Channel Set scans all the
channels that are receivable by your unit. During Auto Channel Set,
the channel numbers are displayed as they are scanned and set.
● When Plug & Play setting has been completed successfully, the
correct clock time is displayed. If you perform Plug & Play setting
successfully, there is no need to perform “Clock Set” (墌 pg. 22) and
“Tuner Set” (墌 pg. 23). If, however, you want to add or delete
channels, refer to “Manual Channel Set” (墌 pg. 23).
During Auto Clock Set
“AUTO” blinks.
VHS/HDD/DVD
STANDBY/ ON
SELECT
S-VIDEO
HDD/DVD
VRS –
VIDEO (MONO)L–AUDIO–R
CH
HDD –
DVD –
DISPLAY
VHS TIMER
REC MODE
DV IN
F–1
During Auto Channel Set
The channel numbers are displayed and “AUTO” blinks as they
are scanned and set.
INFORMATION
● If “AUTO CLOCK” is set to “ON” (墌 pg. 22), the clock will be
adjusted automatically by the host channel every hour (except
11:00 PM, midnight, 1:00 AM and 2:00 AM) using the incoming
PBS channel clock setting data. (This automatic clock adjustment
can only be performed when the unit is turned off. The clock will be
adjusted just on these hours — on the time displayed on the front
display panel, not on the actual real time.) The default setting of
“AUTO CLOCK” is “ON”. (墌 pg. 22)
● If the memory backup fails, because a power outage occurs or
because the AC power cord is unplugged, Plug & Play will be
performed when power is restored to the unit.
What to do if Plug & Play setting failed
● If an incorrect time is displayed on the front display panel, you may
be receiving the clock setting data of a PBS channel from an
adjacent time zone, or an incorrect PBS channel from a cable TV
system. In this case, perform “Semiauto Clock Set” (墌 pg. 22) or
“Manual Clock Set” (墌 pg. 22).
● If “– –:– –” appears on the front display panel, your antenna cable
may not be connected to the unit or there may not be a Host PBS
signal available in your area. Ensure that the antenna cable is
connected correctly. Then turn on and off the unit; the Plug & Play
setting will be automatically reactivated. If Plug & Play setting is
not performed though the antenna cable is connected correctly,
perform “Manual Clock Set” (墌 pg. 22) and “Auto Channel Set”
(墌 pg. 23) or “Manual Channel Set” (墌 pg. 23).
Downloaded From DvDPlayer-Manual.com JVC Manuals
Plug&Play Completed
The current time is displayed.
● If an incorrect clock time or “– –:– –” appears on the front display
panel, see “What to do if Plug & Play setting failed” (墌 pg. 20).
INITIAL SETTINGS
EN
21
On-screen Language Set
Language
This unit offers you the choice to view on-screen messages in 3
different languages.
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
CABLE/DBS
TV
DVD
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “FUNCTION SET UP”, then press t.
4 Press w e to select “DISPLAY
DVD VIDEO SET UP HDD/DVD SET UP
HDD
DVD
SET”, then press t.
5 Press rt to select “ON
SCREEN LANGUAGE”, then
press ENTER.
6 Press rt to select your
desired language, then press
ENTER.
REC/PLAY SET UP
DISPLAY SET
INITIAL SET UP
FUNCTION SET UP
VIDEO IN/OUT
SUPERIMPOSE
AUTO
BLUE BACK
ON
DIMMER
BRIGHT
POWER SAVE
OFF
ON SCREEN LANGUAGE
SET UP
ENTER
EXIT
SELECT
ENGLISH
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
7 Press SET UP to complete the setting.
ENTER
rtwe
Menu/Audio/Subtitle Language Set (DVD deck only)
Some DVD discs contain the DVD menu display, audio and
subtitles in multiple languages. With these discs, you can set the
default language as you like.
SET UP
● The procedure shows how to set “MENU LANGUAGE” as an
example.
1 Press DVD so that the DVD lamp lights up on the unit.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “DVD VIDEO SET UP”, then press t.
4 Press w e to select
DVD VIDEO SET UP HDD/DVD SET UP
“LANGUAGE SET”, then press
ENTER.
5 Press rt to select “MENU
LANGUAGE”, then press ENTER.
6 Press rt to select your
desired language, then press
ENTER.
LANGUAGE SET
AUDIO OUTPUT
MENU LANGUAGE
FUNCTION SET UP
INITIAL SET UP
PARENTAL LOCK
DISC SET UP
ENGLISH
AUDIO LANGUAGE
ENGLISH
SUBTITLE
ENGLISH
SET UP
ENTER
EXIT
SELECT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
● See “Language Code List”
(墌 pg. 94).
7 Press SET UP to complete the setting.
NOTE:
When the selected language is not available on the disc, the disc’s
default menu language is played back.
Downloaded From DvDPlayer-Manual.com JVC Manuals
22
EN
INITIAL SETTINGS
NOTE:
Clock Set
Perform clock setting only if the clock has not been set correctly by
the Plug&Play setting.
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
9 Press SET UP to complete the setting.
IMPORTANT:
Turn off the unit after performing Semiauto Clock. “AUTO” will
appear on the front display panel while the clock is being set. The
current clock time will appear automatically when the clock setting is
complete.
CABLE/DBS
TV
HDD
If an incorrect time is displayed by the Plug & Play function, you may be
receiving the clock setting data of a PBS channel from an adjacent time
zone or from an incorrect PBS channel from a cable TV system. If you
selected “AUTO” for the host channel in step 6, be sure to select the
correct time zone manually.
DVD
DVD
Auto Daylight Saving Time
This function enables automatic adjustment of the unit’s clock at
the start and end of Daylight Saving Time.
With Auto DST activated, —
— on the first Sunday of April at 2:00 AM, the clock is adjusted
to 3:00 AM.
— on the last Sunday of October at 2:00 AM, the clock is
adjusted to 1:00 AM.
NOTE:
ENTER
rtwe
Timer recording may not function correctly at the time Daylight
Saving Time is adjusted.
Manual Clock Set
SET UP
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “INITIAL SET UP”, then press t.
4 Press w e to select “CLOCK
DVD VIDEO SET UP HDD/DVD SET UP
SET”, then press t.
Semiauto Clock Set
The time set previously will be erased when “AUTO CLOCK”, “HOST
CH”, “D.S.T.” or “TIME ZONE” setting is changed.
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “INITIAL SET UP”, then press t.
4 Press w e to select “CLOCK
DVD VIDEO SET UP HDD/DVD SET UP
5 Press rt to select “AUTO
CLOCK [CATV]”, then press
ENTER. Press rt to select “ON”,
then press ENTER.
6 Press rt to select “HOST
STB SET
TUNER SET
STB SET
INITIAL SET UP
FUNCTION SET UP
CLOCK SET
AUTO CLOCK
ON
HOST CH
AUTO
D. S. T.
AUTO
TIME ZONE
AUTO
SET UP
ENTER
EXIT
SELECT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
CH”, then press ENTER.
Press rt to select “AUTO” or the
desired PBS channel number, then press ENTER.
NOTE:
Some PBS channels do not transmit clock setting data.
7 Press rt to select “D.S.T.”, then press ENTER. Press rt to
select the desired setting, then press ENTER.
AUTO: Select if you want to adjust your unit’s clock automatically
by the incoming signal from the host channel. Be sure to select
the correct time zone manually in step 8.
ON: Adjustment will be made by the built-in clock itself.
OFF: Select when Daylight Saving Time does not apply to you.
8 Press rt to select “TIME ZONE”, then press ENTER. Press
rt to select “AUTO” or the desired time zone, then press ENTER.
● Each time you press rt, the time zone changes as follows:
{AUTO{ATLANTIC{EASTERN{CENTRAL{
MOUNTAIN{PACIFIC{ALASKA{HAWAII{
(back to the beginning)
Downloaded From DvDPlayer-Manual.com JVC Manuals
5 Press rt to select “AUTO
CLOCK”, then press ENTER.
Press rt to select “OFF”, then
press ENTER.
6 Press rt to select “TIME”,
then press ENTER. Press rt
until the desired time appears,
then press ENTER to start clock.
INITIAL SET UP
FUNCTION SET UP
CLOCK SET
AUTO CLOCK
You can change the host channel/D.S.T. (Daylight Saving Time)/
time zone setting manually.
NOTE:
SET”, then press t.
TUNER SET
ON
HOST CH
AUTO
D. S. T.
AUTO
TIME ZONE
AUTO
SET UP
ENTER
EXIT
SELECT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
DVD VIDEO SET UP HDD/DVD SET UP
TUNER SET
STB SET
AUTO CLOCK
INITIAL SET UP
FUNCTION SET UP
CLOCK SET
OFF
TIME
--:--
DATE
1/1(THU)
YEAR
2004
D. S. T.
ON
SET UP
ENTER
EXIT
SELECT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
● Set the date and year in the same
way.
● Holding rt changes the time in 30-minutes interval, or changes the
date in 15-days interval.
7 Press rt to select “D.S.T.”, then press ENTER. Press rt to
select the desired setting, then press ENTER.
ON: Adjustment will be made by the built-in clock itself.
OFF: Select when Daylight Saving Time does not apply to you.
8 Press SET UP to complete the setting.
INITIAL SETTINGS
EN
23
Manual Channel Set
Tuner Set
You can add the channels you want or delete the channels you do
not want manually.
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “INITIAL SET UP”, then press ENTER.
4 Press w e to select “TUNER SET”, then press t.
5 Press rt w e to select “MANUAL CH SET”, then press
CABLE/DBS
TV
HDD
DVD
DVD
ENTER.
6 Add or skip the desired channels.
0-9
INITIAL SET UP > MANUAL CH SET
To add channels
A Press rt to select “CH”, then
press ENTER.
B Press the number keys to enter
a channel number you want to
add, then press ENTER.
C Press rt to select “ADD/SKIP”,
then press ENTER.
D Press rt to select “ADD”, then press ENTER.
E Repeat B – D to add other channels.
BAND
CH
ADD/SKIP
ENTER
rtwe
SET UP
ENTER
EXIT
SELECT
7 Press SET UP to complete the setting.
INFORMATION
The unit selects the correct band (TV or CATV) automatically
during Auto Channel Set. The selected band will be displayed on
the right side of “BAND” on the Tuner Set screen.
Auto Channel Set
Perform Auto Channel Set only if channels have not been set
correctly by the Plug&Play setting.
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “INITIAL SET UP”, then press t.
4 Press w e to select “TUNER
DVD VIDEO SET UP HDD/DVD SET UP
TUNER SET
FUNCTION SET UP
STB SET
INITIAL SET UP
CLOCK SET
AUTO CH SET
MANUAL CH SET
GUIDE CH SET
11
5 Press rt w e to select
SET UP
ENTER
EXIT
SELECT
12
13
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
INITIAL SET UP > AUTO CH SET
“AUTO CH SET”, then press
ENTER. You can automatically
set the receivable channels in
your area in the order of their
frequencies.
1
ADD
RETURN
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
To skip channels
A Press rt to select “CH”, then press ENTER.
B Press rt to select a channel number you want to skip, then
press ENTER.
C Press rt to select “ADD/SKIP”, then press ENTER.
D Press rt to select “SKIP”, then press ENTER.
E Repeat B – D to skip other channels.
SET UP
SET”, then press t.
CATV
AUTO CHANNEL SET SCANNING
CANCEL
● When Auto Channel Set is
ENTER SELECT WITH [
SET UP
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
complete, “SCAN COMPLETED”
EXIT
SELECT
appears on the TV screen.
● If the scan was unsuccessful, “SCAN COMPLETED–NO SIGNAL–”
appears on screen. Check the connections and start again.
6 Press SET UP to complete the setting.
Downloaded From DvDPlayer-Manual.com JVC Manuals
24
EN
INITIAL SETTINGS
Cable Box and/or DBS Receiver Control
Setting (HDD & DVD Deck only)
The following procedure is required if you receive your TV
channels through a cable box (descrambler) and/or if you receive
satellite channels through DBS (Direct Broadcast Satellite)
receiver. The Controller allows the unit to automatically switch the
cable box and/or DBS receiver’s channels during timer recording.
NOTES:
● The Controller is effective for “VCR Plus+ C ® Timer Programming”
(墌 pg. 55), or “Manual Timer Programming” (墌 pg. 57).
● When connecting your cable box, refer to its instruction manual.
3
If your cable box or DBS receiver does not have audio/video
output connectors
Connect the RF output connector on the cable box or DBS receiver to the
[VHF/UHF IN] (HDD/DVD) connector on the rear of your unit.
If your cable box or DBS receiver has audio/video output
connectors
Connect the audio/video output connectors on the cable box or
DBS receiver to the [AUDIO/VIDEO INPUT] connectors on the rear
of the unit.
● If both a cable box and a DBS receiver are used, it is recommended
that you connect the DBS receiver to your unit’s [AUDIO/VIDEO
INPUT] connectors and the cable box to your unit’s [VHF/UHF IN]
(HDD/DVD) connector.
4 Connect the Controller to the [CABLE BOX] connector on the
rear panel.
Installing Controller
1 If both a cable box and a DBS receiver are used, position the
Setting Brand And Channel
Controller so its signal reaches the receiving windows of both the
cable box and DBS receiver.
After installation, set the cable box and/or DBS receiver’s brand and
channels correctly; otherwise, the Controller cannot work correctly.
2 Fix securely using the adhesive strip attached on the back of the
Controller.
Cable box or DBS
receiver
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
CABLE/DBS
TV
HDD
Your unit
Controller
(suggested locations)
DVD
DVD
ENTER
rtwe
3 Connect the controller to the unit.
a
Cable box or DBS receiver
To RF output
Transmitter
Controller
To [VHF/UHF IN]
(HDD/DVD)
SET UP
To Audio/video
output
or
To [AUDIO/
VIDEO INPUT]
1 Turn on the cable box and/or DBS receiver.
2 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
Your unit
CABLE
BOX
3 Press SET UP to access the Main Menu screen.
4 Press w e to select “INITIAL SET UP”, then press t.
5 Press w e to select “STB SET”, then press t.
6 Press rt to select “CABLE
SET UP” or “DBS SET UP”, then
press ENTER.
DVD VIDEO SET UP HDD/DVD SET UP
TUNER SET
STB SET
CABLE SET UP
7 Press rt to select “CABLE
BOX OUTPUT CHANNEL” or “DBS
RECEIVER OUTPUT CHANNEL”,
then press ENTER.
SET UP
ENTER
EXIT
SELECT
FUNCTION SET UP
INITIAL SET UP
CLOCK SET
DBS SET UP
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
INITIAL SET UP > CABLE SET UP
CABLE BOX OUTPUT CHANNEL
BRAND
OFF
1
RETURN
Downloaded From DvDPlayer-Manual.com JVC Manuals
SET UP
ENTER
EXIT
SELECT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
INITIAL SETTINGS
8 Select the output channel.
Your selection depends on how the cable box and/or DBS receiver
is connected to your unit.
● If the cable box or DBS receiver is connected to your unit’s
[VHF/UHF IN] (HDD/DVD) connector on the rear panel, press rt
to select the channel number representing the cable box’s output
(CH2 – CH9), then press ENTER.
● If the cable box or DBS receiver is connected to your unit’s
[VIDEO/AUDIO ((MONO) L/R)] input connectors on the front
panel, press rt to select “F-1”, then press ENTER.
● If the cable box or DBS receiver is connected to your unit’s
[AUDIO/VIDEO INPUT] connectors on the rear panel, press rt
to select “L-1”, then press ENTER.
● If you do not use a cable box or DBS receiver, press rt to select
“OFF”, then press ENTER.
9 Press rt to select “BRAND”, then press ENTER. Press rt to
select the brand code from the following list, then press ENTER.
10 Press rt to select “RETURN”, then press ENTER.
CABLE BOX BRAND
CODE
ARCHER
CABLETENNA
CABLEVIEW
CITIZEN
CURTIS
DIAMOND
GC BRAND
GEMINI
GENERAL INSTRUMENTS
HAMLIN
JASCO
JERROLD
NOVAVISION
OAK
PANASONIC
PULSER
RCA
REGAL
REMBRANDT
SAMSUNG
SCIENTIFIC ATLANTA
SIGMA
SL MARX
SPRUCER
STARGATE
TELEVIEW
TOCOM
UNIKA
UNIVERSAL
VIDEOWAY
ZENITH
1, 5, 17
1, 17
15, 16, 17, 21, 25
15, 16, 17, 21, 25
2, 8
1, 17
15, 16, 17, 21, 25
15
1, 4, 6, 11, 12, 15, 28
10, 18, 23
15
1, 4, 6, 11, 12, 15, 28
2, 8
7, 20
13, 14
15, 16, 17, 21, 25
13, 14
10, 18, 23
1, 16, 17
5, 16, 24
2, 8
7, 20
5, 16, 17, 24, 25
13, 14
5, 15, 16, 17, 21, 24, 25
5, 16, 24
1, 4, 16
1, 17
16, 17, 25
3, 9, 22
3, 9, 22
DBS RECEIVER BRAND
CODE
JVC (DISH Network)
ECHOSTAR (DISH Network)
SONY (DSS)
RCA (DSS)
51
51
41
40
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
25
8 For cable box
If the cable box’s channel changes to 9, setting is complete.
Press ENTER and “CABLE BOX
CONTROL IS ON” appears on the
screen for about 5 seconds, then
the screen in step 6 appears.
INITIAL SET UP > CABLE SET UP
DID YOUR CABLE BOX CHANGE TO CHANNEL 09?
If the cable box’s channel does
not change to 9;
A Press w e to select “NO”, then
press ENTER.
B Repeat steps 9 – 10 until the cable box’s channel changes to 9
by entering another code.
C If the channel does not change after going through all the code
numbers listed for your model of cable box, then try all the other
numbers.
8 For DBS receiver
If the DBS receiver’s channel
changes to the channel listed
below for your brand, setting is
complete.
Press ENTER and “DBS
RECEIVER CONTROL IS ON”
appears on the screen for about 5
seconds, then press ENTER. The
screen in step 6 appears.
JVC
] 100
SONY
] 205
ECHOSTAR
] 100
RCA
] 205
YES
SET UP
ENTER
EXIT
SELECT
NO
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
INITIAL SET UP > DBS SET UP
DID YOUR DBS BOX CHANGE TO CHANNEL 100?
YES
SET UP
ENTER
EXIT
SELECT
NO
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
If the DBS receiver’s channel does not change as shown
above;
A Press w e to select “NO”, then press ENTER.
B Repeat steps 9 – 10.
NOTES:
● The Controller may not work with all types of cable box or DBS
receiver.
● If your cable box does not respond to any code between 1 and 28,
you cannot use the Controller to change cable box channels. In this
case, make sure to leave the cable box turned on and tuned to the
proper channel before the scheduled start time of timer recording.
Contact your cable company about the possibility of exchanging your
current cable box with the one compatible with your unit.
● If your DBS receiver does not respond to the code, you cannot use
the Controller to change satellite channels. In this case, make sure to
leave the DBS receiver turned on and tuned to the proper channel
before the scheduled start time of timer recording.
● The unit can only change the cable box or satellite channel through
the Controller during timer recording.
● If your cable box and/or DBS receiver cannot be operated with a
remote control (because it has no receiving window), you cannot use
the Controller to change its channels. Make sure to leave the cable
box and/or DBS receiver turned on and tuned to the proper channel
before the scheduled start time of timer recording.
● If the unit’s memory backup expires because of a power failure, set
the cable box and/or DBS receiver output channels and brands
again.
● For customers in U.S.A.: If you are unable to set the Controller,
contact JVC toll free at 1-800-252-5722.
26
EN
INITIAL SETTINGS
1 Press DVD so that the DVD lamp lights up on the unit.
2 Press SET UP to access the Main Menu screen.
Monitor Set
You can select the monitor type depending on the TV used when
you play back DVD VIDEO discs recorded for wide-screen TVs.
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
CABLE/DBS
TV
DVD
DVD
● You cannot set the monitor type during recording or playback.
3 Press w e to select “FUNCTION SET UP”, then press t.
4 Press w e to select “VIDEO IN/
DVD VIDEO SET UP HDD/DVD SET UP
OUT”, then press t.
5 Press rt to select “MONITOR
TYPE”, then press ENTER.
6 Press rt to select the desired
REC/PLAY SET UP
DISPLAY SET
FUNCTION SET UP
INITIAL SET UP
VIDEO IN/OUT
MONITOR TYPE
4:3LB
F-1 INPUT
VEDIO
L-1 INPUT
VEDIO
option, then press ENTER.
7 Press SET UP to complete the
SET UP
ENTER
EXIT
SELECT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
setting.
* The boldface settings below indicate the settings at your
purchase.
8 MONITOR TYPE — 4:3LB / 4:3PS / 16:9 AUTO / 16:9 FIX
4:3LB (Letter Box conversion): Select this when the aspect ratio of
ENTER
rtwe
SET UP
your TV is 4:3 (conventional TV). While viewing a wide screen
picture, the black bars appear on the top and the bottom of the
screen.
4:3PS (Pan&Scan): Select this when the aspect ratio of your TV is
4:3 (conventional TV). While viewing a wide screen picture, the
black bars do not appear; however, the left and right edges of the
pictures will not be shown on the screen.
16:9 AUTO (Wide television conversion): Select this when the
aspect ratio of your TV is 16:9 (wide TV).
16:9 FIX (Wide television conversion): Select this when the aspect
ratio of your TV is fixed to 16:9 (wide TV). The unit automatically
adjusts the screen width of the output signal correctly when
playing back a picture whose aspect ratio is 4:3.
Pan&Scan/Letter Box
In general, DVD VIDEO disc are produced for a wide-screen TV
with 16:9 aspect ratio.
Material with this ratio will not fit to a TV with 4:3 aspect ratio.
There are two styles to display the image, “Pan&Scan” (PS) and
“Letter Box” (LB).
Pan&Scan
The right and left side of the image are cut off.
The image fills the screen.
● The picture will be shown in the “4:3LB” mode
depending on the disc even if the “4:3PS” mode
is selected.
Letter Box
Black bands appear at the top and bottom of
the image. The image itself appears in 16:9
aspect ratio.
Downloaded From DvDPlayer-Manual.com JVC Manuals
BASIC OPERATIONS ON DVD DECK
EN
27
To play back an MP3/JPEG disc, see “Playback With MP3/WMA/
JPEG Navigation” (墌 pg. 69).
Basic Playback
1 Load a disc.
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
x
VHS/HDD/DVD
4
SELECT
8
9
CABLE/DBS
TV
DVD
DVD
● For details, refer to “Placing A Disc” (墌 pg. 10).
● Pressing 4 also closes the disc tray.
● Playback begins automatically if an auto-playback DVD disc is
loaded.
2 Press VHS/HDD/DVD SELECT on the unit repeatedly or DVD
on the remote so that the DVD lamp lights up on the unit.
3 Press 4 to start playback.
● If you load a DVD disc whose region code does not match the unit,
“REGION CODE ERROR” appears on the TV screen. For details,
refer to “Region Number” (墌 pg. 8).
● If “CAN NOT PLAY BACK DISC UNDER CURRENT SETTING”
appears on the TV screen, refer to “Parental Lock” (墌 pg. 40).
● With Video CD/SVCD discs with PBC control or some DVD discs, the
menu display may appear on the TV screen after starting playback.
In this case, select an item which you want to play back from the
menu. Otherwise, the playback cannot go forward. Refer to
“Playback Control (PBC) Function” (墌 pg. 31) or “Locating A Desired
Scene Using The DVD Menu” (墌 pg. 28).
● The Library Database Navigation also enables you to search and
select the desired titles. (墌 pg. 64)
4 Press 9 to pause playback.
● To resume normal playback, press 4.
5 Press 8 to stop playback.
● When a recordable disc is played, playback stops and a program
received with the unit’s tuner resumes on the TV screen.
● When a playback-only disc is played, playback stops and the still
image at the time you press 8 remains on the TV screen. Pressing 8
again resumes a program received with the unit’s tuner.
● If x is pressed during playback, playback stops, then the disc tray
opens.
ENTER
NOTES:
4
8
9
ATTENTION:
● It takes approximately 30 seconds to read a disc depending on the
type and condition of the disc since this unit is multi-disc
compatible (DVD-RAM, DVD-RW, DVD-R). It may even take
several minutes when a disc is dirty, scratched or warped.
● It may take a few seconds to start playback. This is not a
malfunction.
● Forward/reverse high-speed search and other operations cannot
be performed while playback is stopped.
Downloaded From DvDPlayer-Manual.com JVC Manuals
● When the Library Database Navigation screen appears, choose a
thumbnail image of the desired title on the TV screen, then press
ENTER. (墌 pg. 64)
● It is not possible to playback the DVD disc recorded in 96 kHz on
DVD during recording or Live Memory Playback on HDD.
28
EN
BASIC OPERATIONS ON DVD DECK
Locating The Start Point Of The Item Or Skip The Item
Playback Features
●
●
●
●
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
Press DVD so that the DVD lamp lights up on the unit.
CABLE/DBS
TV
DVD
Press 2 or 6 during playback.
● Pressing 6 locates the start point of the item or skips the item in
the forward direction, then resumes playback.
● Pressing 2 locates the start point of the item or skips the item in
the reverse direction, then resumes playback.
When a DVD-RAM/RW/R disc is played
Current program
DVD
0-9
MARK
TOP MENU
ENTER
rtwe
MENU
2
4
3/SLOW 8
6
5/SLOW +
9
News
Previous
program
Drama
Reverse
Next
program
Movie
Forward
● : marked points (墌 pg. 29)
Example:
To locate the beginning of the next item, press 6 once.
To locate the beginning of the current item, press 2 once.
To locate the beginning of the previous item, press 2 three
times.
When a DVD VIDEO, Audio CD or Video CD/SVCD disc is
played
Playback point
Locating A Desired Scene Using The DVD Menu
DVD VIDEO discs may have top menu and disc menu.
Top menu
DVD discs generally have their own menus which show the disc
contents. These menus contain various items such as titles of a
movie, names of songs, or artist information. You can locate a
desired scene by using the top menu displayed on the TV screen.
Press TOP MENU to access the top menu.
Disc menu
Disc menus include playback data (angle menu, subtitle menu,
etc.) specific to each title.
Press MENU to access the disc menu.
Scene 2
(Chapter 2)
or
Track 2
Reverse
Scene 3
(Chapter 3)
or
Track 3
Scene 4
(Chapter 4)
or
Track 4
Forward
Example:
To locate the beginning of the next item, press 6 once.
To locate the beginning of the current item, press 2 once.
High-Speed Search
1 Press TOP MENU or MENU to
access the DVD menu.
2 Press rt w e to select a
During playback, press 5 for forward high-speed search, or
3 for reverse high-speed search.
desired title, then press ENTER.
Playback starts.
● It may be possible to select the
desired item using the number
keys depending on the menu
display.
● Each press of the button increases the search speed for each
direction.
● To resume normal playback, press 4.
Example:
NOTE:
When “X” appears on the TV screen
in step 1, the disc does not have a top menu or disc menu.
Downloaded From DvDPlayer-Manual.com JVC Manuals
For Audio CD
You can perform 4 levels of speed search with 5 and 3.
(Audio is active also during high-speed search.) You cannot
perform slow motion for each direction.
BASIC OPERATIONS ON DVD DECK
Still Picture/Frame-By-Frame Playback
1 Press 9 to pause during playback.
2 Press SLOW – (3) or SLOW + (5) to activate frame-byframe playback.
● Each press of SLOW – (3) or SLOW + (5) advances/reverses
the still picture frame by frame.
● Frame-by-frame playback for reverse direction cannot be performed
with Video CD/SVCD discs.
● To resume normal playback, press 4.
Slow Motion
1 Press 9 to pause during playback.
2 Press SLOW – (3) or SLOW + (5) for 2 or more seconds.
● Each press of SLOW – (3) or SLOW + (5) increases the slow
motion speed for each direction (from 1/16 to 1/2 times the normal
speed).
● Slow motion for reverse direction cannot be performed with Video
CD/SVCD discs.
EN
29
NOTES:
● “DISC RESUME” setting works on DVD VIDEO, VCD, SVCD and
already finalized DVD-R/DVD-RW (video mode) discs. For other
types of discs, the function under “ON” setting will be applied even if
“RESUME” is set to “DISC RESUME”. (墌 pg. 82)
● If you stop the playback of a disc for which a resume point has
already been memorized, the memory will be updated with the new
resume point.
● After the unit has memorized the resume points for 30 discs,
remembering a new resume point will cause the unit to delete the
oldest memorized point. Stopping playback of a disc for which a
resume point is already stored may change the order in which the
points are stored. This may potentially change the order in which
points are deleted.
● When the unit memorizes a resume point for a disc, it also
remembers audio language, subtitle and angle settings.
● This function may not work for some Video CD/SVCDs.
● When “RESUME” is changed to “ON” or “OFF” (墌 pg. 82), resume
points of the discs memorized with “RESUME” set to “DISC
RESUME” will be cleared.
● Resume points are memorized for each side of a double-sided disc.
● When you switch to HDD during CD playback, playback stops. The
Resume Function doesn’t work when you switch to DVD thereafter to
playback the disc.
Marking Positions To Play Back Again Later
Skip Search
During playback, press
.
● Each press initiates an approximately 30-second period of fastmotion playback. Normal playback resumes automatically.
It is possible to mark positions (up to 999 points) where you want
to play back once again later, and start playback from a marked
position. Marking onto DVD-RAM/RW (VR mode only) discs when
recording is helpful to locate a start point when you play back the
discs later.
Resume Function
To mark positions:
During playback, press MARK at
positions you want to mark.
It is possible to memorize the position where you stop playback
and resume playback from that position.
● Be sure to set “RESUME” to “ON” or “DISC RESUME”. (墌 pg. 82)
1 Press 8 during playback to memorize a resume point.
To delete the marked positions:
While paused, press 2 or 6 to
locate a marked position you want to
delete, then press MARK.
● The unit enters Resume Stop mode and memorizes the position
where you have stopped playback as a resume point. (The inside of
the disc status indicator on the front display panel blinks while
memorizing.)
● The unit retains a memory of the resume points of the last 30 discs
played back, even though they have been ejected if “RESUME” is set
to “DISC RESUME”. (墌 pg. 82)
● To clear the resume points:
(The inside of the disc status indicator stops blinking and lights.)
When “RESUME” is set to “ON”:
• Press 1 to turn off the unit.
• Press x to take out the disc.
• Press 8 in stop mode.
• Press TOP MENU to display the top menu, then start playback by
selecting an item, etc.
• Press MENU to display the disc menu, then start playback by selecting
an item, etc.
When “RESUME” is set to “DISC RESUME”:
• Set “RESUME” to “OFF”. (墌 pg. 82)
• Press 8 in stop mode.
• Press TOP MENU to display the top menu, then start playback by
selecting an item, etc.
• Press MENU to display the disc menu, then start playback by selecting
an item, etc.
2 Press 4 in stop mode to resume playback. The unit starts
playback from the resume point.
Downloaded From DvDPlayer-Manual.com JVC Manuals
● “MARK” appears on the TV screen.
You can easily locate the marked
positions using 2 or 6 when you
play back the disc.
● Crossed “MARK” appears on the TV
screen, and the marked position is
deleted.
NOTES:
● When a monaural program changes to a stereo program while
recording, a mark signal is automatically recorded.
● Titles will be divided into “chapters” at the marked points according to
the disc types as follows:
DVD-R/RW (Video mode): After finalizing, titles are divided into
“chapters” at the marked points that are marked automatically
approximately every 5 minutes during recording before finalizing.
(墌 pg. 88)
DVD-RW (VR mode): After finalizing, titles are divided into “chapters”
at the marked points that are marked at the desired locations during
playback before finalizing. (墌 pg. 88)
DVD-RAM: Titles are divided into “chapters” at the marked points that
are marked at the desired locations during playback.
DVD VIDEO: Creating of marked points are not permitted.
30
EN
BASIC OPERATIONS ON DVD DECK
CABLE/DBS
TV
Angle Selection
DVD
DVD
You can enjoy a variety of scene angles if a DVD VIDEO disc
contains “multi-angle” parts, where the same scene was shot from
different angles.
If the disc contains “multi-angle” parts, “
” appears on the TV
screen at the beginning of the “multi-angle” part.
0-9
1 Press ANGLE during playback.
rtwe
The angle selection display
appears on the TV screen.
RETURN
2 Press ANGLE or w e to select
ENTER
MENU
PREVIOUS
NEXT
When 3 scene angles are
contained.
your desired angle.
4
8
REMAIN
DISPLAY
SET UP
AUDIO
SUBTITLE
● Each time you press ANGLE or
w e, the angle changes.
● When “X” appears on the TV screen, the current scene is not
recorded from multiple angles. In addition, some discs prohibit angle
selection.
● To clear the angle selection display, press ENTER. In addition, the
angle selection display disappears automatically if no operation is
done for 10 seconds.
ANGLE
Subtitle Selection
Checking The Time Information
You can check time information of a disc on the front display panel
and the TV screen.
Each press of DISPLAY changes the display as follows:
8 DVD-RAM/DVD-R/DVD-RW
During recording
Clock time (front display panel only) ] Current title elapsed time
] Disc remaining time* ] (back to the beginning)
* only discs before finalizing
● Clock time is displayed only when a recordable disc is recorded.
During playback
Each title elapsed time ] Current title elapsed time ]
Disc remaining time* ] (back to the beginning)
* only discs before finalizing
In stop mode or during playback
● It is possible to check disc remaining time according to recording
modes also by pressing REMAIN.
● In FR mode, it is possible to set recording time in detail. While the
recording mode and the disc remaining time are displayed by
pressing REMAIN, press rt to select “FR”, then press w e to
select the desired recording time. (墌 pg. 43)
● It is not possible to switch the recording mode during playback or
while recording.
8 Video CD/SVCD/Audio CD
During playback
Current track elapsed time ] Current track remaining time ]
Total elapsed time ] Total remaining time ] (back to the
beginning)
In stop mode
0:00 ] Playback time of track 1 ] 0:00 ] Total length of a disc ]
(back to the beginning)
NOTE:
When a PBC-compatible Video CD/SVCD disc is loaded, deactivate
the PBC function. (墌 pg. 31)
Downloaded From DvDPlayer-Manual.com JVC Manuals
Some DVD VIDEO discs contain more than one subtitle language,
from among which you can choose the desired subtitle language.
“ ” appears on the TV screen at the beginning of the part where
more than one subtitle language are recorded.
1 Press SUBTITLE during
playback. The subtitle selection
display appears on the TV screen.
● Each time you press SUBTITLE,
the subtitle display is switched on
and off.
ENGLISH
When 3 subtitle languages are
contained.
2 Press w e to select your desired language.
● To clear the subtitle selection display, press ENTER.
NOTES:
● When “X” appears on the TV screen, no subtitle language is
recorded.
● When the subtitle language won’t be changed with the procedure
above, change the subtitle on a disc menu displayed by pressing
MENU.
BASIC OPERATIONS ON DVD DECK
Audio Language/Sound Selection
EN
31
● Each time you press AUDIO or w e, the audio language/sound
changes.
● To clear the Audio Language/Sound selection display, press ENTER.
When you can’t switch the audio channel of a bilingual
program
When the unit is connected with a digital audio device using an
optional optical cable and “DIGITAL AUDIO OUT” is set to “DOLBY
DIGITAL/PCM”, it is not possible to switch the audio channel of a
bilingual program recorded on a DVD-RAM or DVD-RW (VR
mode) disc. (墌 pg. 80) In this case, perform the following steps
using the remote control to switch “DIGITAL AUDIO OUT” from
“DOLBY DIGITAL/PCM” to “PCM ONLY”.
A Press SET UP to access the Main Menu screen.
B Press w e to select “DVD VIDEO SET UP”, then press t.
C Press w e to select “AUDIO OUTPUT”, then press t.
D Press rt to select “DIGITAL AUDIO OUT”, then press
ENTER.
E Press rt to select “PCM ONLY”, then press ENTER.
(墌 pg. 81)
F Press SET UP to complete the setting.
G Press AUDIO to select the desired audio channel.
NOTES:
Playback Control (PBC) Function
Some DVD VIDEO discs contain the multiple audio language or
sound. You can select the desired audio language or sound. For
some Video CD/SVCD discs, you can switch the audio channel to
choose Karaoke either with or without the vocal.
1 Press AUDIO during playback.
The Audio Language/Sound
selection display appears.
2 Press AUDIO or w e to select
When 3 audio languages are
contained.
your desired audio language/
sound.
● When “X” appears on the TV screen, no audio language is recorded.
● When the audio language won’t be changed with the procedure
above, change the audio on a disc menu displayed by pressing
MENU.
● Pressing AUDIO to select the audio language/sound is only possible
during playback. It is not possible to select by pressing AUDIO in
stop mode. However, you can select the desired audio language/
sound from the setup menu while in stop mode.
Some Video CD/SVCD discs support the PBC function. PBC is an
abbreviation of “Play Back Control”. A Video CD/SVCD disc
recorded with PBC has its own menus, such as a list of the songs
on the disc. You can locate a specific scene by using the menu.
Audio Channel Selection
1 Press 4 in stop mode. The PBC menu appears.
2 Press the number keys to enter the number of the desired
When watching bilingual programs or playing discs on which you
recorded bilingual or stereo programs, you can choose the desired
audio channel.
● “PBC” appears on the front display panel.
● When “NEXT” or “PREVIOUS” appears on the TV screen:
Pressing NEXT (6) advances to the next page.
Pressing PREVIOUS (2) returns to the previous page.
● You can return to the menu by pressing RETURN.
● The method of the operation is different depending on the disc.
scene. The unit starts playback of the selected item.
● When “SUPERIMPOSE” is set to “AUTO”, you can confirm on the TV
screen the audio channel you have chosen. (墌 pg. 82)
● Each time you press AUDIO, the audio channel
changes.
TRACK
USE
On-Screen Display
For stereo discs
For audio of left channel
For audio of right channel
NOTE:
It is not possible for DVD-R/DVD-RW (Video mode) disc playback to
switch the audio channel. The audio channel is played back as set in
“VIDEO MODE RECORDING AUDIO” setting. (墌 pg. 82)
Downloaded From DvDPlayer-Manual.com JVC Manuals
NOTES:
● If you want to playback a PBC-compatible Video CD/SVCD disc
without activating the PBC function, start playback in stop mode by
using the number keys, instead of the 4 button, to choose the track,
then press ENTER.
● To activate the PBC function when a PBC-compatible Video CD/
SVCD disc is being played back without the PBC function, press TOP
MENU, or press 8 then press 4.
32
EN
BASIC OPERATIONS ON DVD DECK
Recording/playback Status Display
Live Memory Playback
CABLE/DBS
TV
●
●
●
●
DVD
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
Press DVD so that the DVD lamp lights up on the unit.
This unit records pictures onto the DVD-RAM discs, instead of
video tapes, then plays back the pictures recorded on the discs.
This makes it possible to achieve high-speed writing and read-out
that has not been possible with conventional VCRs, enabling
recording and playback simultaneously.
LIVE
High-speed spin
Recording
(High-speed writing)
Playback
(High-speed read-out)
Image figure of DVD-RAM disc
ON SCREEN
Live Memory Playback status can be checked by
pressing ON SCREEN to display the bar meter on
the superimpose display.
It is called “Live Memory Playback” to start playback of the
program being recorded, with a time-lag between a recording point
and a playback point, as shown in the figure below.
Press ON SCREEN. The current status is superimposed on the TV
screen.
Current playback point
(Live Memory Playback)
Current recording position
(Recording point)
Recording start point
Playback
continues
0
30 min.
Bar meter display
Recording
continues
1 hour
Currently elapsed recording time
Not only can this unit play back a program previously recorded
while recording or timer recording another program, but the unit
also allows you to play back from the beginning of a program while
continuing to record the same program.
Downloaded From DvDPlayer-Manual.com JVC Manuals
Superimpose display
BASIC OPERATIONS ON DVD DECK
EN
33
Overview Of Live Memory Playback
You can play back a program you are recording from the beginning while continuing to record or timer record onto a DVD-RAM disc. This
is called “Live Memory Playback”.
(Recording screen)
(Live Memory Playback screen)
To start Live Memory Playback,
press 4 to play back from the
beginning OR press
to
reverse-skip a little
To stop Live Memory
Playback, press 8
Checking the
picture currently
being recorded
To clear, press
LIVE CHECK
To stop recording,
press 8 OR LIVE
To display, press
LIVE CHECK
(Playback and Live Check screen)
To stop Live Memory Playback,
press 8
Recording
stops
Live Memory Playback
picture
CABLE/DBS
TV
DVD
NAVIGATION
Press NAVIGATION to display Library
Database DVD Navi menu, then choose a
program to play back. (墌 pg. 63)
ON SCREEN
LIVE CHECK
Pressing LIVE CHECK during Live Memory
Playback allows you to check the picture
currently being recorded.
Downloaded From DvDPlayer-Manual.com JVC Manuals
NOTES:
Recording
picture
● Live Memory Playback could be performed approximately 30
seconds after recording has started.
● Although high-speed search up to approximately 30 seconds before
the current recording point is possible during Live Memory
Playback, once the current recording point is reached, the unit
resumes normal playback and maintains a delay of approximately
30 seconds so that recording and playback can continue.
● When using Live Memory Playback during timer recording, playback
continues even after the end of the recording.
● When using Live Memory Playback during timer recording, playback
is automatically stopped just before recording starts, and then
recording starts when the time arrives for the next timer-program.
● It is impossible to perform ITR even if you press 7 during Live
Memory Playback. (墌 pg. 42)
Press 8 to display the program being recorded, then perform ITR
settings.
● Playback may be paused for a moment during Live Memory
Playback, which does not interfere with recording.
● Live Memory Playback cannot be performed while recording the
source from DV input. (墌 pg. 74, “DV Dubbing (HDD & DVD Deck
Only)”)
● When LIVE CHECK is pressed to display the picture currently being
recorded, the picture size may not be correct.
34 EN BASIC OPERATIONS ON DVD DECK
Display During Live Memory Playback
During recording, you can watch at your will what was previously recorded or is currently being recorded. It is possible to perform freely
normal playback operations (forward/reverse high-speed search and variable-speed search) within the range of the red or blue bar on the
TV screen.
When Live Memory Playback reaches the point of 30 seconds before the current recording point by forward high-speed search or other
operations, the unit returns to normal playback.
The superimpose display appears by pressing ON SCREEN. (墌 pg. 16)
The Live Check picture is displayed on the bottom right corner by pressing LIVE CHECK.
Recording counter display
(remaining time)
Recording mark
Disc used
Recording channel
Live Memory Playback mark
Recording mode
Bar meter (see below)
Recording mark
Live Check picture
This unit displays the current recording/playback status by the bar meter.
(Example of bar meter display)
Capacity of a disc
Not recorded
Recorded
While stopped
Total length of the program being played
Current playback position
During playback
Capacity of a disc
Remaining capacity when recording started
Current recording position
While recording
Capacity of a disc
Recording start position
Current playback position
Current recording position
Live Memory Playback
Capacity of a disc
Recording start position
Current recording position
Current playback position
Live Memory Playback of
another program
Total length of the program being played back
Blue (recorded part)
Green (playing part)
Orange (recording part)
Black (unrecorded or unplayed part)
Downloaded From DvDPlayer-Manual.com JVC Manuals
BASIC OPERATIONS ON DVD DECK
Buttons To Be Used During Live Memory Playback
●
●
●
●
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
Press DVD so that the DVD lamp lights up on the unit.
CABLE/DBS
TV
DVD
DVD
EN
35
G8
● Pressing once during Live Memory Playback or Live Memory
Recording returns to the screen on air.
● Pressing twice during recording stops recording and returns to the
screen on air.
H9
Pressing once pauses playback (still picture playback). Pressing
repeatedly advances the still picture frame by frame.
I JUMP –
Each press of the button during playback or Live Memory Playback
jumps back for the selected time interval and resumes playback.
(墌 pg. 49, “Jump Search”)
J JUMP +
Each press of the button during playback or Live Memory Playback
jumps forward for the selected time interval and resumes playback.
(墌 pg. 49, “Jump Search”)
K
A
B
C
E
G
I
J
D
F
H
K
L
Pressing once skips forward for approximately 30 seconds and
resumes playback.
Pressing repeatedly skips forward continuously as many times as
pressed.
It is useful when skipping over unwanted sections.
L
Pressing once skips back for approximately 30 seconds and
resumes playback.
Pressing repeatedly skips back for approximately 7 seconds
continuously as many times as pressed.
It is useful when watching sports programs, etc.
M LIVE CHECK
M
A LIVE
Returns to on air program screen. When a confirmation message
appears by pressing this button during timer programming or title
editing, etc., follow the instruction to return to the previous screen.
B NAVIGATION
Displays Library Database Navigation menu. You can choose a
title to play back.
C2
● Pressing once skips back to the beginning of the chapter being
played back.
● Pressing down for 2 or more seconds during playback reverses
playback at 5 times the normal speed while pressed. Releasing the
button resumes normal playback.
Pressing once displays the picture currently being recorded and
the one being played back simultaneously.
Pressing successively clears the Live Check window and displays
only the picture currently being played back.
You can check, for example, if the program you are recording has
already finished.
To Play Back From The Beginning Of The Program
While Recording
You can play back a program you are recording from the beginning
while continuing to record or timer record onto a DVD-RAM disc.
Press 4. Live Memory Playback starts from the beginning of the
program being recorded.
● Pressing 2 or 6 allows you to locate the desired scenes.
Available only when paused
● Pressing down for 2 or more seconds reverses playback at 1/16
times the normal speed.
D6
● Pressing once skips forward to the beginning of the next chapter
being played back.
● Pressing down for 2 or more seconds during playback advances
playback at 5 times the normal speed while pressed. Releasing the
button resumes normal playback.
Available only when paused
● Pressing down for 2 or more seconds advances playback at 1/16
times the normal speed.
E3
● Each press of the button during playback advances the playback
speed in 5 steps in the reverse direction.
Available only when paused
● Each press of the button reverses the still picture frame by frame.
● Pressing down for 2 or more seconds reverses playback at 1/16
times the normal speed. Then, each press of the button reverses
slow-motion at 1/16 times, 1/4 times and 1/2 times the normal
playback.
F5
● Each press of the button during playback advances the playback
speed in 4 steps in the forward direction.
Available only when paused
● Each press of the button advances the still picture frame by frame.
● Pressing down for 2 or more seconds advances playback at 1/16
times the normal speed. Then, each press of the button advances
slow-motion at 1/16 times, 1/4 times and 1/2 times the normal
Downloaded
playback. From DvDPlayer-Manual.com JVC Manuals
To Move Back The Playback Position Slightly While
Recording (One Touch Replay Function)
You can move back the playback position while continuing to
record or timer record onto a DVD-RAM disc.
Press
.
● Each press skips back for approximately 7 seconds and resumes
playback.
● Pressing while paused skips back for approximately 7 seconds and
resumes pause.
To Watch A Program Previously Recorded While
Recording
You can play back a program you recorded previously while
recording.
1 Press 4 during recording. Live Memory Playback starts.
2 Press 2 or 6 to locate the beginning of the desired
program.
NOTE:
To stop playback, press 8. The program being recorded is displayed.
36
EN
BASIC OPERATIONS ON DVD DECK
A
B
C
D
E
F
Using The On-screen Bar
The on-screen bar allows you to control various playback
functions. Some of the functions operated on Navigation Menu can
be controlled on the On-screen bar.
ATTENTION:
The on-screen bar can also be used for the HDD deck.
Be sure to clear Library Database Navigation screen by pressing
NAVIGATION.
Although examples of the on-screen bar are provided here only for 3
types of discs, the on-screen bar will be displayed for whichever disc
indicated in the left column.
CABLE/DBS
TV
Disc type.
Select this for Repeat Playback. (墌 pg. 37)
Select this for A-B Repeat Playback. (墌 pg. 37)
Select this for search function. (墌 pg. 37)
Select this for time search function. (墌 pg. 38)
Select this to switch Simulated Surround Effect function.
(墌 pg. 38)
G Select this for Picture Control function. (墌 pg. 38)
H Select this to switch picture source type. (墌 pg. 39)
I Current status area for the selected item.
J Select this for Program Playback. (墌 pg. 39)
K Select this for Random Playback. (墌 pg. 39)
L Select this to control the switching interval of the slide show.
(墌 pg. 39)
NOTE:
DVD
Basic Operation On The On-screen Bar
Example: When selecting Picture Control function of DVD
During playback or while stopped
1 Press ON SCREEN twice to access the on-screen bar. The item
currently selected is highlighted and pointed by H.
TITLE 99
CHAPTER 99
NAVIGATION
ENTER
3D-ON
DVD-
rtwe
EACH 0:00
CINEMA
AUTO
VIDEO
2 Press w e to select “
”, then press ENTER. The pop-up
window appears under the selected item.
CLEAR
TITLE 99
ON SCREEN
CHAPTER 99
EACH 0:00
3D-ON
DVD-
CINEMA
AUTO
VIDEO
3 Press rt to select the desired option, then press ENTER.
TITLE 99
CHAPTER 99
DVD-
How To Access The On-screen Bar
EACH 0:00
3D-ON
CINEMA
AUTO
VIDEO
1 Press ON SCREEN twice whenever a disc is loaded.
NORMAL
Contents of the on-screen bar during playback
SHARP
DVD VIDEO
SOFT
TITLE 99
CHAPTER 99
CINEMA
EACH 0:00
3D-ON
DVD-
CINEMA
AUTO
VIDEO
To clear the on-screen bar
Press ON SCREEN.
NOTE:
See the corresponding pages for details on each menu item.
Video CD/SVCD
TRACK 99
EACH 0:00
CINEMA
VCD
JPEG disc
GROUP 99 TRACK 99
5 SEC.
JPEG
Downloaded From DvDPlayer-Manual.com JVC Manuals
BASIC OPERATIONS ON DVD DECK
Repeat Playback
EN
37
To clear the on-screen bar
Press ON SCREEN.
To cancel A-B Repeat Playback
Press w e to select “
”, then press ENTER.
You can repeat playback as you like according to the type of disc.
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “ ”, then press ENTER. The pop-up
window appears under the selected item.
TITLE 99
CHAPTER 99
EACH 0:00
3D-ON
DVD-
CINEMA
AUTO
VIDEO
3 Press rt repeatedly to select the desired Repeat mode, then
press ENTER.
DVD-RAM/RW/R
OFF: Repeat playback is not performed.
ALL REPEAT: The whole disc is played back repeatedly.
TITLE REPEAT: The current title is played back repeatedly.
NOTES:
● A-B Repeat Playback may not work properly depending on the type
of disc being used.
● The subtitles recorded around the A-B point may not appear.
● When the end of the item is reached before the end point is set, the
on-screen bar disappears from the TV screen. In such a case, repeat
the procedure from step 1.
● The point B must be set at least 3 seconds after the point A.
● When playing back a DVD, A-B Repeat Playback is possible only
within the same title.
●“
” cannot be selected during Program and Random
Playback.
●“
” cannot be selected while stopped.
Locating The Beginning Of A Desired Selection
DVD VIDEO
OFF: Repeat playback is not performed.
TITLE REPEAT: The current title is played back repeatedly.
CHAPTER REPEAT: The current chapter is played back repeatedly.
Audio CD/Video CD/SVCD/JPEG/MP3
OFF: Repeat playback is not performed.
ALL REPEAT: The whole disc is played back repeatedly.
GROUP REPEAT*: The current group is played back repeatedly.
TRACK REPEAT*: The current track is played back repeatedly.
* “GROUP REPEAT” cannot be selected for Audio CD and Video CD/SVCD
discs.
* “TRACK REPEAT” cannot be selected for JPEG discs.
To clear the on-screen bar
Press ON SCREEN.
To cancel Repeat Playback
Repeat the above procedure from step 1, select “OFF” in step 3,
then press ENTER.
NOTES:
● Repeat Playback is not possible for a Video CD/SVCD with PBC
function.
● Repeat Playback may not work properly depending on the type of the
disc being used.
You can locate the beginning of a title, chapter, group or track.
During playback or while stopped
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “ ”, then press ENTER.
3 Press rt to select the desired item, then press ENTER.
● Skip this step for Video CD/SVCD and Audio CD.
For DVD-RAM/RW/R, DVD VIDEO
“TITLE SEARCH” or “CHAPTER SEARCH” is selectable. (“TITLE
SEARCH” is selectable only while stopped.)
For JPEG, MP3
“GROUP SEARCH” or “TRACK SEARCH” is selectable.
For Video CD/SVCD, Audio CD
“TRACK” is selectable.
GROUP 99
CHAPTER 99
DVD-
EACH 179:59
5
CINEMA
VIDEO
TITLE SEARCH
CHAPTER SEARCH
4 Press the number keys to enter the desired item number, then
A-B Repeat Playback
press ENTER.
● Playback starts from the selected section.
Examples:
A To select track 5, press the number key “5”.
B To select track 15, press the number key “1” and “5”.
C To select track 25, press the number key “2”, then “5”.
You can repeat the desired part.
During playback
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “
”.
3 Press ENTER at the beginning of the desired part you want to
repeat (point A). The elapsed playing time of the point A appears.
TITLE 99
CHAPTER 99
3D-ON
CINEMA
AUTO
VIDEO
A
1 : 25 : 58
B
:
:
4 Press ENTER at the end of the desired part you want to repeat
(point B). The elapsed playing time of the point B appears.
● The selected part of the disc (between point A and B) is played
repeatedly.
TITLE 99
CHAPTER 99
EACH 0:00
3D-ON
DVD-
CINEMA
VIDEO
A
1 : 25 : 58
B
1 : 40 : 00
To clear the on-screen bar
Press ON SCREEN.
NOTES:
EACH 0:00
DVD-
If you have specified a wrong selection
Press RETURN on the remote control unit and repeat the above
procedures from step 2.
Downloaded From DvDPlayer-Manual.com JVC Manuals
AUTO
● When “X” is displayed on the TV screen in step 4, the chapter you
have selected is not contained in the disc, or chapter search does not
work on the disc.
● Before you press ENTER, playback may start automatically when
you enter the section’s number depending on the disc.
● This function is not possible for a Video CD/SVCD with PBC function.
38
EN
BASIC OPERATIONS ON DVD DECK
CABLE/DBS
TV
Simulated Surround Effect
DVD
It is possible to get a simulated surround effect from your stereo
system. You can enjoy the virtual surround sound with your
2-channel stereo system.
0-9
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “
”, then press ENTER.
CANCEL
● “3D-ON” appears above the selected item and Simulated Surround
Effect is activated.
● Each time you press ENTER, “3D-ON” appears and disappears
alternately.
ENTER
rtwe
6
2
TITLE 99
4
CLEAR
CHAPTER 99
EACH 0:00
3D-ON
DVD-
CINEMA AUTO
VIDEO
ON SCREEN
To clear the on-screen bar
Press ON SCREEN.
To cancel the simulated surround effect
Press ENTER to clear “3D-ON” from the screen.
NOTES:
Time Search
You can play back a disc from the desired point by specifying the
elapsed playing time from the beginning of a program (DVD-RAM,
DVD-R, DVD-RW, DVD VIDEO and HDD) or a disc (Video CD/
SVCD and Audio CD).
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “
”, then press ENTER. The pop-up
window appears under the selected item.
TITLE 99
CHAPTER 99
EACH 0:00
CINEMA
DVD-
AUTO
VIDEO
● Simulated Surround Effect works correctly only when playing back a
title recorded in multichannels.
● Simulated Surround Effect does not affect the DVD VIDEO bitstream
signal from the [DIGITAL AUDIO OUT] connectors.
● When Simulated Surround Effect is activated, the settings of
“ANALOG AUDIO OUT” and “D. RANGE CONTROL” are disabled.
(墌 pg. 81)
Adjusting The Picture Quality
You can obtain optimal picture quality by selecting an appropriate
picture mode.
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “ ”, then press ENTER. The pop-up
window appears under the selected item.
3 Press the number keys to enter the time, then press ENTER.
Playback starts from the specified time.
Example:
To play back from a point 12 (minutes): 50 (seconds) elapsed.
TITLE 99
CHAPTER 99
DVD-
EACH 0:00
CINEMA
AUTO
VIDEO
3 Press rt to select the desired option, then press ENTER.
Press 1
Press 2
NORMAL: Normally select this option.
CINEMA: Suitable for a movie disc, etc.
SHARP: Clearer, sharper-edged picture when viewing images with
lots of flat, same-colored surfaces such as cartoons.
Press 5
Press 0
SOFT: Select this option when too much noise appears.
To clear the on-screen bar
Press ON SCREEN.
If you have specified a wrong selection,
Press RETURN on the remote control unit and repeat the above
procedures from step 2.
To clear the on-screen bar
Press ON SCREEN.
NOTES:
● When “X” is displayed on the TV screen in step 3, you have selected
a point that exceeds the recording time of the disc.
● Some DVD VIDEO discs do not contain time information, and it is not
possible to use the Time Search function. In such cases, “X” is
displayed on the TV screen as well.
● This function is not possible for a Video CD/SVCD with PBC function.
Downloaded From DvDPlayer-Manual.com JVC Manuals
BASIC OPERATIONS ON DVD DECK
EN
39
4 Press 4. Playback starts in the programmed order.
Setting The Progressive Mode
You can obtain optimal picture quality by selecting whether the
content on the disc is processed by field (video source) or by frame
(film source).
1 Set the unit to the progressive scan mode. (墌 pg. 83)
2 Press ON SCREEN twice to access the on-screen bar.
3 Press w e to select “ ”, then press ENTER. The pop-up
window appears under the selected item.
● When all of the programmed tracks have been played back, Program
Playback stops, but the programmed information remains.
● To add tracks to the end of the program, perform steps 1 through 3.
● During Program Playback, pressing 6 skips to the next selection
of the program. Pressing 2 returns to the beginning of the current
selection.
To clear the on-screen bar and the contents of the program
Press ON SCREEN.
To cancel Program Playback
Press w e to select “PRGM”, then press ENTER.
NOTE:
Program Playback is not possible depending on the type of disc.
TITLE 99
CHAPTER 99
EACH 0:00
3D-ON
DVD-
CINEMA
AUTO
Random Playback
VIDEO
4 Press rt to select the desired option, then press ENTER.
AUTO: This mode automatically detects film and video content for
You can play back all the tracks on the disc in random order.
progressive playback. When film content is found, flag detection
is used to invoke playback of film data in full screen. When video
content is found, pictures from multiple fields are used to detect
sections with movement, and then this movement undergoes
advanced image processing for output of sharp, detailed
progressive images without any reduction in image quality where
movement occurs. Normally, operation in this mode is
recommended.
FILM: Suitable for playing back a progressive scanned film source
disc.
VIDEO: Suitable for playing back a video source disc. The outlines
on the played back pictures will be soft.
While stopped
To clear the on-screen bar
Press ON SCREEN.
To cancel Random Playback
Perform steps 1 and 2.
NOTE:
Program Playback
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “RND”, then press ENTER. Playback starts
in random order.
TRACK 99
EACH 0:00
CINEMA
VCD
To clear the on-screen bar
Press ON SCREEN.
The same track will not be played back more than once during Random
Playback.
Select The Switching Interval Of The Slide Show
You can program up to 30 tracks (Video CD/SVCD or Audio CD) to
play back in the desired order.
While stopped
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “PRGM”, then press ENTER. The program
table appears under on-screen bar.
TRACK 99
You can control the switching interval of the slide show.
1 Press ON SCREEN twice to access the on-screen bar.
2 Press w e to select “ ”, then press ENTER. The pop-up
window appears under the selected item.
EACH 0:00
GROUP 99 TRACK 99
CINEMA
VCD
5 SEC.
JPEG
3 Press the number keys to
enter the track numbers in the
desired order.
Examples:
A To select track 5, press the
number key “5” and ENTER.
B To select track 15, press the
number key “1” and “5”.
C To select track 25, press the number key “2” and “5”.
If you have specified a wrong selection
Press CANCEL (&). The last selection is erased.
Or press CLEAR (8). The whole selection is erased.
Downloaded From DvDPlayer-Manual.com JVC Manuals
3 Press rt to select the desired option, then press ENTER.
● Each time you press rt, the interval changes as follows:
5 SEC. { 10 SEC. { 15 SEC. { 20 SEC. { 25 SEC. {
30 SEC. { (Back to the beginning)
To clear the on-screen bar
Press ON SCREEN.
NOTE:
JPEG files are played back as a slide show. It may take more time to
display an image with larger file size.
40
EN
BASIC OPERATIONS ON DVD DECK
9 Press the number keys to enter the same password as in
Parental Lock
step 6 above, then press ENTER.
10 Press SET UP to complete the setting.
NOTE:
Remember your password, or make a note of it.
This function restricts playback of DVD VIDEO discs which contain
violent (and other) scenes according to the level set by the user.
For example, if a movie which includes violent scenes supports the
parental lock feature, such scenes which you do not want to let
children view can be cut or replaced by other scenes.
●
●
●
●
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
Press DVD so that the DVD lamp lights up on the unit.
To Change The Settings
You can change the Parental Lock settings later.
1 Perform steps 1 to 3 of “To Set Parental Lock For The First
Time” to access the “PARENTAL LOCK” screen before continuing.
To change the level
2 Press rt to select “PARENTAL LEVEL”, then press ENTER.
3 Press rt to select the desired level, then press ENTER.
To change the country code
4 Press rt to select “COUNTRY CODE”, then press ENTER.
5 Press rt to select your country code, then press ENTER.
CABLE/DBS
TV
DVD
● See “Country/Area Code List for Parental Lock” (墌 pg. 95).
DVD
6 Press the number keys to enter the same password as in
step 6 of “To Set Parental Lock For The First Time”, then press
ENTER.
0-9
7 Press SET UP to complete the setting.
NOTE:
If you forget your password, enter “8888” in step 6.
ENTER
To Temporarily Release Parental Lock
rtwe
When you set the Parental Lock level strictly, some discs may not
be played back at all. When you insert such a disc and try to play it
back, the confirmation screen appears on the TV screen, asking
you whether you want Parental Lock to be temporarily released or
not.
SET UP
1 Load a disc.
● If the disc is rated higher than the selected level, the confirmation
screen appears.
2 Press w e to select “YES”, then press ENTER.
● If you select “NO”, you cannot play back that disc.
3 Press the number keys to enter the same password as in
step 6 of “To Set Parental Lock For The First Time”, then press
ENTER.
To Set Parental Lock For The First Time
While stopped
1 Press SET UP to access the Main Menu screen.
2 Press w e to select “DVD VIDEO SET UP”, then press t.
3 Press w e to select
“PARENTAL LOCK”, then press
t.
DVD VIDEO SET UP HDD/DVD SET UP
LANGUAGE SET
AUDIO OUTPUT
PARENTAL LEVEL
FUNCTION SET UP
INITIAL SET UP
PARENTAL LOCK
DISC SET UP
● When you enter the correct password, the Parental Lock is released
and the unit starts playback.
● If you enter a wrong password, “ENTRY ERROR” appears on the TV
screen. Enter the correct password.
● If you have successively entered wrong password three times,
“ENTRY ERROR CAN NOT CHANGE PASSWORD” appears on the
TV screen. In such a case, press ENTER. The disc will stop. Then
play back the disc again, and try the procedure again from step 1.
NONE
COUNTRY CODE
NOTE:
US
If you forget your password, enter “8888” in step 3.
4 Press rt to select
“PARENTAL LEVEL”, then press
ENTER.
5 Press rt to select the desired
level, then press ENTER.
● The smaller the value of level is,
the more restrictive the Parental
Lock level becomes.
● Select “NONE” to cancel the
restriction.
SET UP
ENTER
EXIT
SELECT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
DVD VIDEO SET UP HDD/DVD SET UP
LANGUAGE SET
AUDIO OUTPUT
PARENTAL LEVEL
FUNCTION SET UP
INITIAL SET UP
PARENTAL LOCK
DISC SET UP
NONE
COUNTRY CODE
SET UP
ENTER
EXIT
SELECT
US
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
6 Press the number keys to enter your desired four-digit number,
then press ENTER.
● If you made a mistake, enter a correct number again.
7 Press rt to select “COUNTRY CODE”, then press ENTER.
8 Press rt to select your country code, then press ENTER.
● If you do not need to change your country code, jump to 10.
● See “Country/Area
Code List for Parental Lock”
(墌Manuals
pg. 95)
Downloaded
From DvDPlayer-Manual.com
JVC
BASIC OPERATIONS ON DVD DECK
EN
41
7 Press 8 twice to stop recording.
Basic Recording
● It takes about 10 seconds to end the writing session when you stop
recording.
NOTES:
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
ATTENTION:
It is not possible to record programs on a DVD-R disc which has
already been finalized.
VHS/HDD/DVD
SELECT
4 9
CH +/
REC 7
MODE
8
CABLE/DBS
TV
DVD
● It is recommended to format a DVD-RAM disc before use if you use
the disc on this unit for the first time.
● When using a brand-new DVD-RW disc, format the disc either in VR
mode or in Video mode. (墌 pg. 87)
● Recordings made on DVD-R/RW disc must be finalized to play back
on other DVD players. Perform “Finalize A Disc (DVD Deck Only)”
(墌 pg. 88).
● You can record up to 99 programs and 999 play lists on each disc.
● Some programs can only be recorded one time.
● When recording is started, an index of the first part of recording is
automatically recorded. (墌 pg. 63) To record satellite programs,
refer to page 59. To delete the index, refer to page 65.
● Recording sometimes may stop or cannot be performed even if there
is enough available capacity remaining on the disc.
● It is not possible to record on both DVD and HDD simultaneously.
Recording Mode
MPEG2 format is used as recording format. As a guide for picture
quality, the “bps” unit is used to represent how much data can be
recorded per second. The larger this value is, the better the picture
quality becomes but more capacity is required for the recording.
Select XP or SP for programs where quick movement occurs, such
as sports programs, and LP or EP for talk shows, etc. with
relatively less movement.
The recording modes for a 4.7 GB disc are set as follows:
DVD
Recording
mode
0-9
CH+/-
ENTER
4
7
8
REC MODE
XP
1 Load a recordable disc.
● For details, refer to “Placing A Disc” (墌 pg. 10).
2 Press VHS/HDD/DVD SELECT on the unit repeatedly or DVD
on the remote so that the DVD lamp lights up on the unit.
3 Press CH +/– or the number keys to select the channel you
wish to record.
4 Press REC MODE repeatedly to select the recording mode,
then press ENTER.
● Each time you press REC MODE, the recording mode changes as follows:
XP ] SP ] LP ] EP ] FR60–FR360* ] FR420, FR480 ] (Back
to the beginning)
* The value is selectable from 1 to 6 hours in 5-minutes interval by
pressing w e repeatedly after selecting “FR60–FR360”. To change the
value in 30-minutes interval, press and hold w e.
● For details on the recording mode, see the right column.
5 Press 7 on the unit to start recording. Or while holding 7, press
4 on the remote control.
● The DVD recording lamp lights up on the unit.
6 Press 7 and 9 on the remote control simultaneously to pause
recording.
● To resume recording, press 7 and 4 simultaneously.
Downloaded From DvDPlayer-Manual.com JVC Manuals
10 Mbps
Maximum recording
time (approx.)
1 hour
SP
5 Mbps
2 hours
LP
2.5 Mbps
4 hours
EP
1.6 Mbps
6 hours
FR60–FR360
(墌 pg. 43)
The amount varies
depending on the
selected time.
1 – 6 hours
FR420
9
Recording amount
(approx.)
FR480
7 hours
8 hours
● For details on FR mode, refer to “Free Rate Function” (墌 pg. 43)
42
EN
BASIC OPERATIONS ON DVD DECK
Instant Timer Recording (ITR)
Recording Features
●
●
●
●
This easy method lets you record for from 30 minutes to 6 hours
(selectable in 30-minutes interval), and shuts the unit off after
recording is finished.
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
Press VHS/HDD/DVD SELECT on the unit repeatedly or DVD on
the remote so that the DVD lamp lights up on the unit.
1 Press 7 on the unit to start recording.
2 Press 7 again to engage the ITR mode.
● On the front display panel, “0:30” appears.
3 If you want to record for more than 30 minutes, press 7 to
extend the time. Each press extends recording time by 30 minutes.
NOTES:
● You can only perform ITR using the 7 button on the unit.
● When the recording capacity becomes full during timer recording or
Instant Timer Recording, the unit automatically performs “Relief
Recording” (墌 pg. 57).
VHS/HDD/DVD
SELECT
Watch Another Program While Recording On The Unit
DISPLAY
7
CABLE/DBS
TV / VIDEO
TV
DVD
DVD
While recording is going on, you can watch another program on
the TV by using the TV’s tuner.
NOTE:
It is required that the remote control is set to be able to operate the TV
in advance. (墌 pg. 78)
1 During recording, press TV/VIDEO to select TV mode if your
unit is connected to the TV via the RF connection.
● VHS mode is disengaged, and the VIDEO indicator on the front
display panel lights off .
VIDEO indicator lights off.
CH+/-
● The program received on the TV’s tuner is displayed on the TV
screen.
2 Slide the TV/CABLE/DBS/DVD switch to TV.
3 Press CH +/– repeatedly to select the desired channel.
REMAIN
DISPLAY
Elapsed Recording Time And Disc Remaining Time
Indication
During recording, press DISPLAY repeatedly until the desired
indication appears on the front display panel.
● Each time you press DISPLAY, the time indication changes as
follows:
Elapsed recording time ] Disc remaining time ] Clock ] (Back to
the beginning)
● You can also check the disc remaining time by pressing REMAIN
while the unit is stopped or recording is in progress. The list of disc
remaining times for all recording modes appears on the TV screen.
Downloaded From DvDPlayer-Manual.com JVC Manuals
BASIC OPERATIONS ON DVD DECK
Free Rate Function
● Note that this function is available only for timer programming
recording (墌 pg. 55, 57) and dubbing from HDD to DVD (墌 pg. 70).
8 To record the entire program by specifying the desired
recording time
Select “FR60–FR360”, “FR420” or “FR480” in a recording mode
selection procedure. (墌 pg. 41, 44, 55, 57)
8 To record a 25-min. long daily program five times just on
the same DVD disc for example
Perform “VCR Plus+ C ® Timer Programming” (墌 pg. 55)
procedure. Be sure to set the recording mode to “FR125” and set
Weekly/Daily Rec Function to “MON–FRI” in step 8 to fit the total
recording time to the whole disc space.
3
A: 1st
B: 2nd
C: 3rd
D: 4th
E: 5th
When the same program is recorded in SP mode instead of in
“FR125”, the 5th program cannot be recorded.
Blank
43
NOTES:
To record the entire program, the unit automatically sets the
appropriate recording mode depending on the combination of the
total time of the program to be recorded and either the remaining
disc space or the specified recording time (from 60 minutes to 480
minutes).
8 To record the entire program within the actual remaining
disc space (DVD deck only)
Select “FR (JUST)” in a recording mode selection procedure.
Blank
EN
A: 1st
B: 2nd
C: 3rd
D: 4th
E: Blank (20 min.)
Downloaded From DvDPlayer-Manual.com JVC Manuals
● You can program this unit to timer-record, regardless of the disc
remaining time. When the disc remaining time is not enough, the unit
performs “Relief Recording” (墌 pg. 57). To avoid this, make sure of
the disc remaining time before setting timer programming.
(Example) If you programmed to timer-record for 60 minutes in SP
mode on a 120-minute disc, the disc remaining time would be 30
minutes in XP mode, 60 minutes in SP mode, 120 minutes in LP
mode, 180 minutes in EP mode, and 240 minutes in FR480 mode.
Timer-recording will not complete beyond these remaining times.
● The maximum recording time of FR (JUST) mode is the same as the
recording time of FR480 mode. When timer programming a long
program in FR (JUST) mode on a disc whose remaining time is short,
it is recommended to check the disc remaining time in FR480 mode
to see if the remaining time is enough for the program.
● Even if more than one program are timer programmed in FR (JUST)
mode, only the first one is recorded.
● In order to ensure that the recording fits on the disc, this feature may
leave a slight non-recorded section at the end of the disc.
● There may be some noise and sound disturbance at the point on the
disc where the unit switches the mode.
Second Audio Recording
This unit’s built-in MTS decoder enables reception of Multichannel
TV Sound broadcast. To record a SAP program received, set “2ND
AUDIO RECORD” to “ON”. (墌 pg. 82)
NOTE:
When the channel is changed on the unit;
● The “MONO” indicator appears on the screen for about 5 seconds if
the program is a monaural broadcast.
● The “STEREO” indicator appears on the screen for about 5 seconds
if the program is a stereo broadcast.
● Both “STEREO” and “SAP” indicators appear when a stereo program
is accompanied by SAP sound.
● Both “MONO” and “SAP” indicators appear when the main audio on
the monaural broadcast is accompanied by SAP sound.
44
EN
BASIC OPERATIONS ON HDD DECK
Basic Recording
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
ATTENTION:
The HDD on the unit requires approximately 20 seconds to start up
after the unit has been turned on, during which no operation can be
made.
HDD Lamp
VHS/HDD/DVD
SELECT
Pause recording on HDD deck
It is not possible to pause recording. Pressing 9 initiates Live
Memory Playback.
However, it is still possible to pause recording only when recording
the channels of external sources (“L-1”, “F-1”, and “DV”). While
holding 7, press 9 on the remote. To resume recording, while
holding 7, press 4 on the remote.
No operation can be made with the buttons on the unit.
Recording Mode
MPEG2 format is used as recording format. As a guide for picture
quality, the “bps” unit is used to represent how much data can be
recorded per second. The larger this value is, the better the picture
quality becomes but more capacity is required for the recording.
Select XP or SP for programs where quick movement occurs, such
as sports programs, and LP or EP for talk shows, etc. with
relatively less movement.
Recording
mode
CH +/
8 7
CABLE/DBS
TV
DVD
HDD
CH+/-
Maximum recording
time (approx.)
XP
10 Mbps
18 hours
SP
5 Mbps
35 hours
LP
2.5 Mbps
70 hours
EP
1.6 Mbps
105 hours
The amount varies
depending on the
selected time.
18 – 105 hours
FR60–FR360
(墌 pg. 43)
0-9
Recording amount
(approx.)
FR480
147 hours
● For details on FR mode, refer to “Free Rate Function” (墌 pg. 43)
NOTE:
The maximum recording time stated in the above table are the
approximate time under unused condition.
4
8
7
9
REC MODE
1 Press VHS/HDD/DVD SELECT on the unit repeatedly or HDD
on the remote so that the HDD lamp lights up on the unit.
2 Press CH +/– or the number keys to select the channel you
wish to record.
3 Press REC MODE repeatedly to select the recording mode,
then press ENTER.
● Each time you press REC MODE, the recording mode changes as
follows:
XP ] SP ] LP ] EP ] FR60–FR360* ] FR420, FR480 ]
(Back to the beginning)
* The value is selectable from 1 to 6 hours in 5 minutes interval by
pressing w e repeatedly after selecting “FR60–FR360”. To change the
value in 30 minutes interval, press and hold w e.
● For details on the recording mode, see the right column.
4 Press 7 on the unit to start recording. Or while holding 7, press
4 on the remote control.
● The HDD recording lamp lights up on the unit.
5 Press 8 twice to stop recording.
● Pressing 8 once displays the confirmation message to stop
recording. Press 8 again to terminate recording.
NOTES:
● Continuous recording for over 48 hours is not possible.
● It is not possible to record on both DVD and HDD simultaneously.
Downloaded From DvDPlayer-Manual.com JVC Manuals
BASIC OPERATIONS ON HDD DECK
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
Press VHS/HDD/DVD SELECT on the unit repeatedly or HDD
on the remote so that the HDD lamp lights up on the unit.
HDD Lamp
45
Instant Timer Recording (ITR)
Recording Features
●
●
●
●
EN
This easy method lets you record for from 30 minutes to 6 hours
(selectable in 30-minutes interval), and shuts the unit off after
recording is finished.
1 Press 7 on the unit to start recording.
2 Press 7 again to engage the ITR mode.
● On the front display panel, “0:30” appears.
3 If you want to record for more than 30 minutes, press 7 to
extend the time. Each press extends recording time by 30 minutes.
VHS/HDD/DVD
SELECT
NOTES:
● You can only perform ITR using the 7 button on the unit.
● When the recording capacity becomes full during timer recording or
Instant Timer Recording, the unit is automatically shut off.
Watch Another Program While Recording On The Unit
CH +/
DISPLAY
7
CABLE/DBS
TV / VIDEO
HDD
TV
DVD
While recording is going on, you can watch another program on
the TV by using the TV’s tuner.
NOTE:
It is required that the remote control is set to be able to operate the TV
in advance. (墌 pg. 78)
1 During recording, press TV/VIDEO to select TV mode if your
unit is connected to the TV via the RF connection.
CH+/-
● VHS mode is disengaged, and the VIDEO indicator on the front
display panel lights off.
VIDEO indicator lights off.
● The program received on the TV’s tuner is displayed on the TV
screen.
REMAIN
2 Slide the TV/CABLE/DBS/DVD switch to TV.
3 Press CH +/– repeatedly to select the desired channel.
DISPLAY
Elapsed Recording Time And Disc Remaining Time
Indication
During recording, press DISPLAY repeatedly until the desired
indication appears on the front display panel.
● Each time you press DISPLAY, the time indication changes as
follows:
Elapsed recording time ] Disc remaining time ] Clock ] (Back to
the beginning)
● You can also check the disc remaining time by pressing REMAIN
while the unit is stopped or recording is in progress. The list of disc
remaining times for all recording modes appears on the TV screen.
Second Audio Recording
This unit’s built-in MTS decoder enables reception of Multichannel
TV Sound broadcast. To record a SAP program received, set “2ND
AUDIO RECORD” to “ON”. (墌 pg. 82)
NOTE:
When the channel is changed on the unit;
● The “MONO” indicator appears on the screen for about 5 seconds if
the program is a monaural broadcast.
● The “STEREO” indicator appears on the screen for about 5 seconds
if the program is a stereo broadcast.
● Both “STEREO” and “SAP” indicators appear when a stereo program
is accompanied by SAP sound.
● Both “MONO” and “SAP” indicators appear when the main audio on
the monaural broadcast is accompanied by SAP sound.
Downloaded From DvDPlayer-Manual.com JVC Manuals
46
EN
BASIC OPERATIONS ON HDD DECK
Basic Playback
Playback Features
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
●
●
●
●
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
Press HDD so that the HDD lamp lights up on the unit.
VHS/HDD/DVD
SELECT
4
CABLE/DBS
TV
DVD
HDD
8
9
CABLE/DBS
TV
DVD
HDD
4
3/SLOW -
5/SLOW +
9
ENTER
4
8
9
High-Speed Search
During playback, press 5 for forward high-speed search, or
3 for reverse high-speed search.
● Each press of the button increases the search speed for each
direction.
● To resume normal playback, press 4.
ATTENTION:
● It may take a few seconds to start playback. This is not a
malfunction.
● Forward/reverse high-speed search and other operations cannot
be performed while playback is stopped.
1 Press VHS/HDD/DVD SELECT on the unit repeatedly or HDD
on the remote so that the HDD lamp lights up on the unit.
2 Press 4 to start playback.
● The Library Database Navigation also enables you to search and
select the desired programs. (墌 pg. 64)
3 Press 9 to pause playback.
● To resume normal playback, press 4.
4 Press 8 to stop playback.
NOTE:
When the Library Database Navigation screen appears, choose a
thumbnail image of the desired title on the TV screen, then press
ENTER. (墌 pg. 64)
Still Picture/Frame-By-Frame Playback
1 Press 9 to pause during playback.
2 Press SLOW – (3) or SLOW + (5) to activate frame-byframe playback.
● Each press of SLOW – (3) or SLOW + (5) advances/reverses
the still picture frame by frame.
● To resume normal playback, press 4.
Slow Motion
1 Press 9 to pause during playback.
2 Press SLOW – (3) or SLOW + (5) for 2 or more seconds.
● Each press of SLOW – (3) or SLOW + (5) increases the slow
motion speed for each direction (from 1/16 to 1/2 times the normal
speed).
Skip Search
During playback, press
.
● Each press initiates an approximately 30-second period of fastmotion playback. Normal playback resumes automatically.
Downloaded From DvDPlayer-Manual.com JVC Manuals
BASIC OPERATIONS ON HDD DECK
EN
47
Recording/playback Status Display
Live Memory Playback
CABLE/DBS
●
●
●
●
TV
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
Press HDD so that the HDD lamp lights up on the unit.
This unit records pictures onto the hard disc, instead of video
tapes, then plays back the pictures recorded on the disc. This
makes it possible to achieve high-speed writing and read-out that
has not been possible with conventional VCRs, enabling recording
and playback simultaneously.
LIVE
NAVIGATION
Press NAVIGATION to display Library Database
Navigation menu, then choose a program to play
back. (墌 pg. 63)
High-speed spin
Recording
(High-speed writing)
DVD
Playback
(High-speed read-out)
8
ON SCREEN
Live Memory Playback status can be checked by
pressing ON SCREEN to display the bar meter on
the superimpose display. The current status is
superimposed on the TV screen. (墌 pg. 17, “When
using Live Memory playback”)
Image figure of the hard disc
It is called “Live Memory Playback” to start playback of the
program being recorded, with a time-lag between a recording point
and a playback point, as shown in the figure below.
Current playback point
(Live Memory Playback)
NOTES:
Current recording position
(Recording point)
Recording start point
Playback
continues
0
30 min.
Recording
continues
1 hour
Currently elapsed recording time
Not only can this unit play back a program previously recorded
while recording or timer recording another program, but the unit
also allows you to play back from the beginning of a program while
continuing to record the same program.
Temporary recording for Live Memory
This unit automatically records the channel being received, within
the specified range of time, to the reserved space on the hard disc.
The time range can be set for 30 minutes, 1 hour, and 3 hours.
(墌 pg. 82)
NOTE:
Previous temporary recordings will be overwritten since the unit is
always recording the channel being received. Thus, it is not possible to
play back TV programs recorded beyond the specified range of time
since they are already overwritten. To avoid this in order to save titles,
perform normal recording (墌 pg. 44), timer recording (墌 pg. 55, 57),
or Live Memory Recording (墌 pg. 49).
About limitation on temporary recording
The temporary recording for Live Memory is canceled in the
following cases, and will start all over again when it is to resume.
● When the power is turned off
● When the system is powered again after a power failure was
occurred
● When normal recording, timer recording, Live Memory Recording,
or Automatic Satellite Program Recording (墌 pg. 59) is performed
● When the “LIVE MEMORY” setting is changed (墌 pg. 82)
● When tuner channel setting is performed (墌 pg. 23)
● When dubbing is performed by pressing DUBBING (墌 pg. 70)
● When “DV” is selected by pressing CH +/– (墌 pg. 74)
Downloaded From DvDPlayer-Manual.com JVC Manuals
● Live Memory Playback could be performed approximately 30
seconds after recording has started.
● Although high-speed search up to approximately 30 seconds before
the current recording point is possible during Live Memory Playback,
once the current recording point is reached, the unit resumes normal
playback and maintains a delay of approximately 30 seconds so that
recording and playback can continue.
● When using Live Memory Playback during timer recording, playback
continues even after the end of the recording.
● When using Live Memory Playback during timer recording, playback
is automatically stopped just before recording starts, and then
recording starts when the time arrives for the next timer-program.
● It is impossible to perform ITR even if you press 7 during Live
Memory Playback. (墌 pg. 45)
Press 8 to display the program being recorded, then perform ITR
settings.
● Playback may be paused for a moment during Live Memory
Playback, which does not interfere with recording.
● Live Memory Playback cannot be performed while recording the
source from DV input. (墌 pg. 74, “DV Dubbing (HDD & DVD Deck
Only)”)
● When LIVE CHECK is pressed to display the picture currently being
recorded, the picture size may not be correct.
● Press 7 or LIVE to stop Live Memory Playback.
● Live Memory Playback cannot be performed even if the “LIVE
MEMORY” in “HDD SET UP” is set to other than “OFF”, as temporary
recording on HDD stops during recording on DVD.
48 EN BASIC OPERATIONS ON HDD DECK
Buttons To Be Used During Live Memory Playback
●
●
●
●
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
Press HDD so that the HDD lamp lights up on the unit.
CABLE/DBS
TV
DVD
HDD
F5
● Each press of the button during playback advances the playback
speed in 4 steps in the forward direction.
Available only when paused
● Each press of the button advances the still picture frame by frame.
● Pressing down for 2 or more seconds advances playback at 1/16
times the normal speed. Then, each press of the button advances
slow-motion at 1/16 times, 1/4 times and 1/2 times the normal
playback.
G8
● Pressing once during Live Memory Playback or Live Memory
Recording returns to the screen on air.
● Pressing twice during recording stops recording and returns to the
screen on air.
H9
Pressing once pauses playback (still picture playback). Pressing
repeatedly advances the still picture frame by frame.
A
B
I JUMP –
Each press of the button during playback or Live Memory Playback
jumps back for the selected time interval and resumes playback.
(墌 pg. 49, “Jump Search”)
C
D
J JUMP +
E
G
F
H
K
L
Each press of the button during playback or Live Memory Playback
jumps forward for the selected time interval and resumes playback.
(墌 pg. 49, “Jump Search”)
I
J
M
K
Pressing once skips forward for approximately 30 seconds and
resumes playback.
Pressing repeatedly skips forward continuously as many times as
pressed.
It is useful when skipping over unwanted sections.
A LIVE
L
Returns to on air program screen. When a confirmation message
appears by pressing this button during timer programming or title
editing, etc., follow the instruction to return to the previous screen.
Pressing once skips back for approximately 30 seconds and
resumes playback.
Pressing repeatedly skips back for approximately 7 seconds
continuously as many times as pressed.
It is useful when watching sports programs, etc.
B NAVIGATION
Displays Library Database Navigation menu. You can choose a
title to play back.
C2
● Pressing once skips back to the beginning of the chapter being
played back.
● Pressing down for 2 or more seconds during playback reverses
playback at 5 times the normal speed while pressed. Releasing the
button resumes normal playback.
Available only when paused
● Pressing down for 2 or more seconds reverses playback at 1/16
times the normal speed.
D6
● Pressing once skips forward to the beginning of the next chapter
being played back.
● Pressing down for 2 or more seconds during playback advances
playback at 5 times the normal speed while pressed. Releasing the
button resumes normal playback.
Available only when paused
● Pressing down for 2 or more seconds advances playback at 1/16
times the normal speed.
E3
● Each press of the button during playback advances the playback
speed in 5 steps in the reverse direction.
Available only when paused
● Each press of the button reverses the still picture frame by frame.
● Pressing down for 2 or more seconds reverses playback at 1/16
times the normal speed. Then, each press of the button reverses
slow-motion at 1/16 times, 1/4 times and 1/2 times the normal
playback.
Downloaded From DvDPlayer-Manual.com JVC Manuals
M LIVE CHECK
Pressing once displays the picture currently being recorded and
the one being played back simultaneously.
Pressing successively clears the Live Check window and displays
only the picture currently being played back.
You can check, for example, if the program you are recording has
already finished.
BASIC OPERATIONS ON HDD DECK
To Play Back The Previous Part Of The Channel
Currently Recording or Watching
You can play back the previous part of the channel you are
recording or watching (temporarily recorded on the background)
from the desired point. (墌 pg. 47, “Temporary recording for Live
Memory”)
1 Press 2 or 3 to locate the point to start playback from.
● Each press of 3 increases the reverse search speed.
2 Press 4 to start Live Memory Playback.
3 Press 8 to stop Live Memory Playback.
● The on-air screen resumes.
NOTES:
● You can use various playback features during Live Memory
Playback. (墌 pg. 46)
● If you have started actual recording by pressing 7, pressing 8 in
step 3 only resumes the on-air screen. To stop actual recording,
press 8 again.
To Record From The Previous Part Of The Channel
Currently Watching (Live Memory Recording)
You can start recording from the previous part of the channel you
are currently watching (temporarily recorded on the background).
(墌 pg. 47, “Temporary recording for Live Memory”)
1 Press 2 or 3 to locate the point to start recording from.
● Each press of 3 increases the reverse search speed.
2 Press 7 on the unit to start Live Memory Recording. Or while
holding 7, press 4 on the remote control.
3 Press 8 to stop Live Memory Recording.
● The on-air screen resumes.
NOTES:
To Move Back The Playback Position Slightly While
Recording (One Touch Replay Function)
You can move back the playback position while continuing to
record or timer record.
Press
.
● Each press skips back for approximately 7 seconds and resumes
playback.
● Pressing while paused skips back for approximately 7 seconds and
resumes pause.
To Resume Playback Of A TV Broadcast From The
Paused Point
You can resume playback of a TV broadcast you were recording or
watching from the point you have paused.
1 Press 9 to pause a TV broadcast.
● Recording continues when recording.
2 Press 4 to start Live Memory Playback.
● Playback resumes from the paused position.
3 Press 8 to resume the on-air screen.
Downloaded From DvDPlayer-Manual.com JVC Manuals
49
1.5x Speed Search
You can play back a title quickly. (This feature can also be
performed with normal playback.)
1.5x speed search cannot be performed during recording on HDD
or DVD.
1 Press 3 to locate the point to start 1.5x speed search from.
2 Press 4 to resume playback.
3 Press 5 once.
● Pressing ON SCREEN displays “+X1.5” on the top right corner of the
screen.
NOTE:
When the unit is connected with a digital audio device using an optional
optical cable, set “DIGITAL AUDIO OUT” to “PCM ONLY”. (墌 pg. 31)
Jump Search
You can locate a scene ahead or behind the current one by
jumping scenes according to selected time intervals (墌 pg. 82)
during playback (or Live Memory Playback). This feature is also
available during recording (or Live Memory Recording) or when
watching a TV received program.
Press JUMP – or JUMP +.
● To advance forward or back, press JUMP – or JUMP + repeatedly
within 5 seconds of each press to continue jump.
● When you cannot advance any further (beginning or end of program
reached), the message “UNABLE TO GO BACK ANY MORE”
appears on the screen and the on-air screen resumes. In such a
case, press 2, 3 or 8.
Example 1:
Playback search when jump interval is set to 30 MIN jumps
Time counter
0 min
40 min
30 min
● You cannot use Live Memory Recording for channels other than the
channel you are currently watching.
● Recording speed is automatically set to SP mode when Live Memory
Recording is started.
● Temporarily recorded data prior to the beginning of Live Memory
Recording is erased when Live Memory Recording started.
EN
Beginning of program
1 h 15 min
1h
Current scene
End of program
Example 2:
Recording search when jump interval is set to 15 MIN jumps
Clock time
9:00
9:15
Beginning of program
9:30
9:40
9:45
Current scene
10:15
10:00
End of program
50
EN
BASIC OPERATIONS ON VHS DECK
1 Load a cassette. Make sure the window side is up, the rear label
Basic Playback
side is facing you and the arrow on the front of the cassette is
pointed toward the unit.
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
VHS/HDD/DVD
SELECT
4
● Do not apply too much pressure when inserting.
● If the record safety tab has been removed, playback begins
automatically.
● The unit’s power comes on automatically and the counter is reset to
0:00:00.
2 Press VHS/HDD/DVD SELECT on the unit repeatedly or VHS
on the remote so that the VHS lamp lights up on the unit.
5
3 Find the program start point. If the tape is advanced past the
start point, press 3. To go forward, press 5.
4 Press 4 to start playback.
5 Press 8 to stop playback.
● To eject the cassette, press x (VHS).
8
x
3
CABLE/DBS
TV
DVD
VHS
Clean the video heads using a dry cleaning cassette TCL-3F - when:
● Rough, poor picture appears while a tape is played back.
● The picture is unclear or no picture appears.
● “USE CLEANING CASSETTE” appears on the screen (only with
“SUPERIMPOSE” set to “AUTO”). (墌 pg. 84)
NOTE:
The heads get dirty in the following cases:
● in an environment prone to extreme temperature or humidity
● in a dusty environment
● flaw, dirt or mold on video tapes
● continuous usage for a long time
Usable cassettes
4
3
5
8
Full-Size VHS
T-30 (ST-30**)
T-60 (ST-60**)
T-90
T-120 (ST-120**)
T-160 (ST-160**)
ST-210**
Compact VHS*
TC-20 (ST-C20**)
TC-30 (ST-C30**)
TC-40 (ST-C40**)
* Compact VHS camcorder recordings can be played on this
unit. Simply place the recorded cassette into a VHS Cassette
Adapter and it can be used just like any full-sized VHS
cassette.
** This unit can record on regular VHS and Super VHS
cassettes.
However, it will record regular VHS signals only.
• S-VHS recording is not possible with this unit.
● This unit is equipped with SQPB (S-VHS QUASI PLAYBACK) that
lets you watch tapes recorded in the S-VHS format and the SP
mode with regular VHS resolution.
• SQPB does not deliver Super VHS resolution.
Downloaded From DvDPlayer-Manual.com JVC Manuals
BASIC OPERATIONS ON VHS DECK
During playback, press 5 for forward high-speed search, or
3 for reverse high-speed search.
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
Press VHS/HDD/DVD SELECT on the unit repeatedly or VHS on
the remote so that the VHS lamp lights up on the unit.
CABLE/DBS
TV
VHS
51
High-Speed Search
Playback Features
●
●
●
●
EN
DVD
1
DVD
CH+/-
● Each press of the button increases the search speed for each
direction.
When pressing 5:
(SP): +5x{+7x
(EP): +11x{+21x
When pressing 3:
Once 3 is pressed, reverse search starts in –1x normal playback
speed. After this process, each press of 3 changes the search
speed between –5x and –7x in SP mode, –11x and –21x in EP mode.
(SP): –1x]–5x{–7x
(EP): –1x]–11x{–21x
● To resume normal playback, press 4.
Quick Rewind A Little
During playback (or Live Memory Playback), press
. The unit
rewinds the picture a little (about 7 seconds) and resumes
playback.
● If the button is pressed repeatedly, the unit rewinds the pictures
continuously and resumes playback.
2
3
8
6
4
5
9
REC MODE
Skip Search
During playback, press
sections.
1 to 6 times to skip over unwanted
● Each press initiates an approximately 30-second period of fastmotion playback. Normal playback resumes automatically.
● To resume normal playback, press 4.
Index Search
AUDIO
PROGRESSIVE
SCAN
ATTENTION:
In the search, still, slow-motion or frame-by-frame playback mode,
● the picture will be distorted.
● the noise bars will appear.
● there may be a loss of color.
● you cannot hear the sound.
Still Picture/Frame-By-Frame Playback
1 Press 9 to pause during playback.
● If there is vertical jitter, press CH +/– to correct the picture.
2 Press 9 to activate frame-by-frame playback.
● To resume normal playback, press 4.
Slow Motion
1 Press 9 to pause during playback.
2 Press and hold 9 for 2 seconds, then release. Press 9 and
Your unit automatically marks
index codes at the beginning of
each recording. This function
gives you quick access to any one
of the 9 index codes in either
direction.
NOTE:
Before starting, make sure the unit is
in the Stop mode.
Press 2 or 6 to activate Index Search. “INDEX –1” or “INDEX 1” is
displayed on the TV screen and search begins in the corresponding
direction.
● To access index codes 2 through 9, press 2 or 6 repeatedly
until the correct index number is displayed.
Example:
To locate the beginning of B from the current position, press 2
twice.
To locate the beginning of D from the current position, press 6
once.
Current position
release again to return to still picture.
● The speed changes for each direction by pressing 3 and 5
repeatedly.
● To resume normal playback, press 4.
NOTE:
During slow motion playback, some noise may appear on the TV
screen. Press CH + or – to eliminate the noises.
Index number
● When the specified index code is located, playback begins
automatically.
Downloaded From DvDPlayer-Manual.com JVC Manuals
52 EN BASIC OPERATIONS ON VHS DECK
Next Function Memory
The Next Function Memory “tells” the unit what to do after
rewinding. Before continuing, make sure the unit is in the Stop
mode.
For Automatic Start Of Playback
Press 3, then press 4 within 2 seconds.
Repeat Playback
Soundtrack Selection
Your unit is capable of recording three soundtracks (HI-FI L, HI-FI
R and NORM) and will play back the one you select.
During Playback
Pressing AUDIO changes the soundtrack as follows:
TRACK
USE
On-Screen Display
Your unit can automatically play back the whole tape 100 times
repeatedly.
HI-FI
Hi-Fi sound is played back
1 Press 4 to start playback.
2 Press and hold 4 for over 5 seconds, then release.
HI-FI L
Sound on the left Hi-Fi channel is
played back
●
lights up on the front display panel.
● After playing back a tape 100 times, the unit stops automatically.
HI-FI R
Sound on the right Hi-Fi channel is
played back
3 Press 8 at any time to stop Repeat Playback.
NORM
Sound on the normal track is played
back
Manual Tracking
NORM
HI-FI
Both sounds on the Hi-Fi track and
normal track are mixed and played
back
● Pressing 4, 3, 5 or 9 also stops Repeat Playback.
Your unit is equipped with automatic tracking control. During
playback, you can override this and adjust the tracking manually by
pressing the CH buttons.
1 During playback, press CH + or – on the unit simultaneously to
activate manual tracking.
2 Press CH + or – to adjust the tracking manually.
NOTES:
● “HI-FI” should normally be selected. In this mode, Hi-Fi stereo tapes
are played back in stereo, and the normal audio track is played back
automatically for tapes with only normal audio.
● “SUPERIMPOSE” must be set to “AUTO” or the on-screen displays
will not appear. (墌 pg. 84)
VHS Progressive Scan
You can watch the images on VHS deck in the Progressive scan
mode via component video.
● To return to automatic tracking, press CH + or – simultaneously or
eject and insert the tape again.
ATTENTION:
NOTE:
Your TV needs to be compatible with Progressive and to have
Component video input connectors.
When a new tape is inserted, the unit enters the automatic tracking
mode automatically.
1 Set the Progressive-compatible TV to the component input
mode.
2 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
3 Press PROGRESSIVE SCAN for 3 or more seconds.
● The video output indicator
lights up on the front display panel.
4 Press VHS so that the VHS lamp lights up on the unit, then
press PROGRESSIVE SCAN.
● “COMP OFF” is displayed on the front display panel. It will be
displayed for 5 seconds.
5 Press PROGRESSIVE SCAN again within 5 seconds.
● “COMP ON” is displayed on the front display panel.
● The VHS progressive scan image will then be outputted from the
[COMPONENT VIDEO OUT (Y/PB/PR)] connectors.
NOTES:
● Be sure to engage the HDD or DVD deck in stop mode.
● To disengage the VHS Progressive Scan mode, perform steps 4 and
5 to switch to “COMP OFF”.
Downloaded From DvDPlayer-Manual.com JVC Manuals
BASIC OPERATIONS ON VHS DECK
Basic Recording
53
Recording Features
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
VHS/HDD/DVD
SELECT
4 9
CH +/
EN
●
●
●
●
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
Press VHS/HDD/DVD SELECT on the unit repeatedly or VHS on
the remote so that the VHS lamp lights up on the unit.
VHS/HDD/DVD 7
SELECT
7
REC
MODE
8
CABLE/DBS
CABLE/DBS
TV
DVD
TV/VIDEO
TV
DVD
VHS
VHS
0-9
CH+/-
CANCEL
CH+/-
4
7
8
9
REC MODE
1 Load a cassette with the record safety tab intact.
● The unit’s power comes on automatically and the counter is reset to
0:00:00.
2 Press VHS/HDD/DVD SELECT on the unit repeatedly or VHS
on the remote so that the VHS lamp lights up on the unit.
3 Press CH +/– or the number keys to select the channel you
wish to record.
4 Press REC MODE repeatedly to set the recording mode.
5 Press 7 on the unit to start recording. Or while holding 7, press
4 on the remote control.
● The VHS recording lamp lights up on the unit.
DISPLAY
Watch Another Program While Recording On The Unit
While recording is going on, you can watch another program on
the TV by using the TV’s tuner.
NOTE:
It is required that the remote control is set to be able to operate the TV
in advance. (墌 pg. 78)
1 During recording, press TV/VIDEO to select TV mode if your
unit is connected to the TV via the RF connection.
● VHS mode is disengaged, and the VIDEO indicator on the front
display panel lights off.
VIDEO indicator lights off.
6 Press 9 to pause recording.
● You can select channel during the Record Pause mode.
● To resume recording, press 4.
7 Press 8 to stop recording.
● The VHS recording lamp lights off on the unit.
Recording Resume Function
If there is a power outage during recording, Instant Timer
Recording or timer recording (墌 pg. 54, 60, 61), the recording will
resume automatically when power is restored to the unit unless the
unit’s memory backup has expired.
Downloaded From DvDPlayer-Manual.com JVC Manuals
● The program received on the TV’s tuner is displayed on the TV
screen.
2 Slide the TV/CABLE/DBS/DVD switch to TV.
3 Press CH +/– repeatedly to select the desired channel.
54 EN BASIC OPERATIONS ON VHS DECK
Instant Timer Recording (ITR)
Second Audio Recording
This easy method lets you record for from 30 minutes to 6 hours
(selectable in 30-minutes interval), and shuts the unit off after
recording is finished.
This unit’s built-in MTS decoder enables reception of Multichannel
TV Sound broadcast. To record a SAP program received, set “2ND
AUDIO RECORD” to “ON”. (墌 pg. 85)
1 Press 7 on the unit to start recording.
2 Press 7 again to engage the ITR mode.
NOTE:
● On the front display panel, “0:30” appears.
3 If you want to record for more than 30 minutes, press 7 to
extend the time. Each press extends recording time by 30 minutes.
NOTES:
● You can only perform ITR using the 7 button on the unit.
● When the end of the tape is reached during timer recording or Instant
Timer Recording, the cassette is automatically ejected and the unit is
shut off.
● During Instant Timer Recording, any other timer programmed
recording won’t start even if their start time has come. In such a case,
the timer programmed recording starts (if the end time of the timer
programmed recording is set after the end of Instant Timer
Recording) after the Instant Timer Recording finishes.
When the channel is changed on the unit;
● The “STEREO” indicator appears on the screen for about 5 seconds
if the program is a stereo broadcast.
● The “SAP” indicator appears on the screen for about 5 seconds if the
program is a SAP broadcast.
● Both indicators appear when a stereo program is accompanied by
SAP sound.
Accidental erasure prevention
To prevent accidental recording on
a recorded cassette, remove its
safety tab. To record on it later,
cover the hole with adhesive tape.
Elapsed Recording Time Indication
1 Press DISPLAY until a counter reading appears on the front
display panel.
2 Press CANCEL to reset the counter before starting recording or
playback.
● The counter is reset to “0:00:00” and shows the exact elapsed time
as the tape runs. You can check the exact time of a recording or
playback.
Tape Remaining Time
1 Press DISPLAY until the time remaining on the tape appears.
● By pressing the DISPLAY button, you can change display to show
the clock time, counter reading or tape remaining time.
NOTES:
● When you press DISPLAY, the on-screen display appears on the TV
screen for 5 seconds, then the displays other than the counter
disappears. To clear the counter display, press DISPLAY.
● Depending on the type of tape being used, the tape remaining time
reading may not appear right away, or is not correct.
“– –:– –” may sometimes appear, or the display may blink on
occasion.
Downloaded From DvDPlayer-Manual.com JVC Manuals
Record safety tab
TIMER RECORDING ON HDD/DVD DECK
3
VCR Plus+ C ® Timer Programming
● To cancel this setting, press RETURN.
IMPORTANT:
Make sure the channel position number you wish to record is
displayed; if not, see “Changing VCR Plus+® Setting” (墌 pg. 86) and
set the Guide Channel number correctly.
8 Press rt to select the desired recording option as required.
Press rt to select the desired setting, then press ENTER.
● “INPUT TITLE” (墌 pg. 64, “Modify Title Name”)
● “CATEGORY” (墌 pg. 65, “Modify Category”)
● “WEEKLY/DAILY” (墌 pg. 56, “Weekly/Daily Recording”)
● “REC MODE” (墌 pg. 41, “Recording Mode”)
9 Press rt to select “OK”, then press ENTER to access the
Program Confirmation screen.
Make sure that the unit’s built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
CABLE/DBS
TV
55
recording information are displayed on the TV screen. Check the
program data.
You can program this unit to timer-record as many as
32 programs.
With the VCR Plus+ system, timer programming is greatly
simplified because each TV program has a corresponding code
number which your unit is able to recognize.
You can use the remote control to enter the PlusCode number.
●
●
●
●
EN
7 The PlusCode number you entered and the matching timer-
DVD
10 Press w e to select “EXIT”, then press ENTER to complete
timer programming.
● To program another timer, press w e to select “CONTINUE”, then
press ENTER.
● If “PROGRAM OVERLAPPED” appears on the TV screen, see
page 58.
0–9
PROGRAM
NOTES:
● There may be cases that the VCR Plus+ Timer Programming
function prolongs the stop time of the programming.
● When two successive programs are recorded on a DVD-RW disc
with the VCR Plus+ Timer Programming function, the beginning of
the second one may be left off the recording.
● If the copy limited program is received during timer-recording, the unit
enters Record Pause mode. Recording starts again if it is switched to
a recordable broadcast during the time you programmed.
ENTER
RETURN
IMPORTANT:
If you have moved to a different area or if a broadcasting station’s
channel number has been changed, the wrong channel number will
be displayed on the VCR Plus+ program screen in step 7. When this
happens, set the correct Guide Channel number for that station.
(墌 pg. 86, “Changing VCR Plus+® Setting”)
1 Load a recordable disc if recording to DVD.
2 Press PROGRAM to access the program top screen.
3 Press rtw e to select “VCR Plus+ PR.”, then press ENTER.
● When “PROGRAM FULL DELETE UNWANTED TIMER
PROGRAMS” appears on the TV screen, you need to cancel some of
the reserved programs. (墌 pg. 58)
4 Press the number keys to
123
enter the VCR Plus+ number of a
program you wish to record.
OR
Press rtw e to select the
desired number key on the
screen, then press ENTER.
Repeat to enter all required
numbers.
PROGRAM > VCR PLUS+ (1/2)
PLUS CODE NO.
1234
1
4
7
SELECT WITH [
]
THEN PRESS [ENTER]
PRESS [PROGRAM]
TO EXIT
PROGRAM
ENTER
EXIT
SELECT
DELETE
2
5
8
0
3
6
9
DELETE ALL
RECORD TO
DVD
CONFIRM
● If you have made a mistake, press rtw e to select “DELETE” or
“DELETE ALL’, then press ENTER and input the correct number
before you press ENTER again.
5 Press rt to select “RECORD TO”, then press ENTER. Press
rt to select the desired recording deck, then press ENTER.
6 Press rtw e to select “CONFIRM”, then press ENTER.
● If the number you entered is invalid, “PLUSCODE NO. ERROR
CONFIRM PLUSCODE NO. THEN RETRY” appears on the TV
screen. Input a valid PlusCode number.
● If “GUIDE PROGRAM IS NOT SET SET GUIDE PROGRAM THEN
RETRY” appears on the TV screen, set Guide Channel Numbers
manually. (墌 pg. 86)
Downloaded From DvDPlayer-Manual.com JVC Manuals
Cable Box and DBS Receiver Users
To timer-record a satellite broadcast using the VCR Plus+
system:
A Perform “Cable Box and/or DBS Receiver Control Setting
(HDD & DVD Deck only)” (墌 pg. 24).
3
B Perform “VCR Plus+ C ® Timer Programming” (墌 pg. 55).
C Leave the cable box or DBS receiver’s power on.
56 EN TIMER RECORDING ON HDD/DVD DECK
Weekly/Daily Recording
You can record programs with one of the following weekly/daily
timer settings.
For the HDD deck
When you select a mode other than ONCE, the space on the hard
disk drive is saved for new recordings by overwriting previous
recordings. To prevent loss of a needed recording, backup
programs you wish to save by dubbing them to DVD discs before
overwriting previous recordings. Or save the title of weekly/daily
programs to avoid overwriting of a previous week/day. (墌 pg. 58)
ONCE (One Time Recording)
In this mode a program will not be automatically overwritten.
WEEKLY (OVERWRITE) (Weekly Recording/Weekly Overwrite)
When the set weekly program is broadcast, the program recorded
last week is automatically deleted and overwritten by the new
program. Save the title of each program you wish to save, then the
recorded program is saved and will not be overwritten by the new
program.
This week’s drama
Overwritten
Last week’s drama
MON–SUN (FOR A WEEK)/ MON–SAT (FOR A WEEK)/ MON–FRI
(FOR A WEEK) (Daily Recording/Weekly Overwrite)
When the set weekly program is broadcast, the program recorded
on the same day last week is automatically deleted and overwritten
by the new program. Save the title of each program you wish to
save, then the recorded program is saved and will not be
overwritten by the new program.
Overwritten
This
week
MON TUE
WED THU
FRI
Last
week
MON TUE
WED THU
FRI
MON–SUN (OVERWRITE)/ MON–SAT (OVERWRITE)/ MON–FRI
(OVERWRITE) (Daily Recording/Daily Overwrite)
When the set daily program is broadcast, yesterday’s program is
automatically deleted and overwritten by the new program. Save
the title of each program you wish to save, then the recorded
program is saved and will not be overwritten by the new program.
Tuesday’s program
Overwritten
Monday’s program
For the DVD deck
ONCE (One Time Recording)
WEEKLY (Weekly Recording)
MON–SUN/ MON–SAT/ MON–FRI (Daily Recording)
Downloaded From DvDPlayer-Manual.com JVC Manuals
TIMER RECORDING ON HDD/DVD DECK
Manual Timer Programming
57
to select the desired source, then press ENTER.
You can program this unit to timer-record as many as
32 programs.
If you do not know the VCR Plus+ number for the program you
wish to record, use the following procedure to set your unit to
timer-record the program.
●
●
●
●
EN
8 Press rt to select “SOURCE”, then press ENTER. Press rt
● To select the desired source, the respective settings must be set,
refer to ‘Source Selection’ (墌 pg. 57).
9 Press rt to select “CH”, then press ENTER. Press rt to
select the desired channel.
10 Press rt to select “CONFIRM”, then press ENTER.
11 Set the other recording options as required.
● Refer to step 8 in “VCR Plus+ C3® Timer Programming” (墌 pg. 55).
Make sure that the unit’s built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
12 Press rt to select “OK”,
13 Press w e to select “EXIT”,
then press ENTER to complete
timer programming.
CABLE/DBS
TV
2
then press ENTER to access the
Program Confirmation screen.
DVD
PROGRAM > CALENDAR PROG. (3/3)
01/08/03 WED 10:30PM - 11:00PM DBS 100
GARDENING
[EDUCATION] FR360
1:00
28:00
SELECT WITH [
]
THEN PRESS [ENTER]
INPUT TITLE
PRESS [PROGRAM]
TO EXIT
WEEKLY/DAILY
CATEGORY
REC MODE
GARDENING
EDUCATION
MON-FRI (FOR A WEEK)
FR360
ENTER
PROGRAM
● To program another timer, press
OK
EXIT
SELECT
w e to select “CONTINUE”, then
press ENTER.
● If “PROGRAM OVERLAPPED” appears on the TV screen, see
page 58.
NOTES:
● When two successive programs are recorded on a DVD-RW disc
with Manual Timer Programming function, the beginning of the
second one may be left off the recording.
● If the copy limited program is received during timer-recording, the unit
enters Record Pause mode. Recording starts again if it is switched to
a recordable broadcast during the time you programmed.
PROGRAM
ENTER
rtwe
Cable Box and DBS Receiver Users
To timer-record a satellite broadcast using Manual Timer
Programming:
A Perform “Cable Box and/or DBS Receiver Control Setting
(HDD & DVD Deck only)” (墌 pg. 24).
B Perform “Manual Timer Programming” (墌 pg. 57).
C Leave the cable box or DBS receiver’s power on.
1 Load a recordable disc if recording to DVD.
2 Press PROGRAM to access the program top screen.
3 Press rtw e to select “CALENDAR PR.”, then press ENTER.
● When “PROGRAM FULL DELETE UNWANTED TIMER
PROGRAMS” appears on the TV screen, you need to cancel some of
the reserved programs. (墌 pg. 58)
4 Press rtw e to select the desired date, then press ENTER.
5 Press rt to select “RECORD
2
TO”, then press ENTER. Press
rt to select the desired
recording deck, then press
ENTER.
6 Press rt to select “START”,
then press ENTER. Press rt to
set the desired start time, then
press ENTER.
PROGRAM > CALENDAR PROG. (2/3)
01/08/03 WED 10:30PM - 11:00PM
DBS 100
[MISC. ] XP
SELECT WITH [
]
THEN PRESS [ENTER]
RECORD TO
START
10:30PM
PRESS [PROGRAM]
TO EXIT
STOP
11:00PM
HDD
SOURCE
DBS
CH
PROGRAM
100
ENTER
OK
EXIT
SELECT
● Each press of rt increases/decreases the start time in 1-minute
interval.
● To increase/decrease the start time in 30-minutes interval, press and
hold rt.
7 Press rt to select “STOP”, then press ENTER. Press rt to
set the desired stop time, then press ENTER.
● Each press of rt increases/decreases the stop time in 1-minute
interval.
● To increase/decrease the stop time in 30-minutes interval, press and
hold rt.
Downloaded From DvDPlayer-Manual.com JVC Manuals
Relief Recording
When a program that is set for the DVD deck cannot be
recorded properly, the program is recorded to the HDD deck
instead in XP mode.
● If the remaining capacity of the hard disc is not sufficient, the
program is recorded to the DVD deck until the remaining capacity
of the DVD disc lasts.
● If “JUST” is selected for the recording mode, the current recording
mode for the DVD deck is applied.
Source Selection
To select the desired source (TV, CATV, DBS or AUX), the
respective settings must be set as follows:
“TV”: The “CABLE BOX OUTPUT CHANNEL” setting on the
“CABLE SET UP” screen must be set to “OFF” (墌 pg. 24),
and the “BAND” setting on the “MANUAL CH SET” set to “TV”
(墌 pg. 23).
“CATV”: The “CABLE BOX OUTPUT CHANNEL” setting on the
“CABLE SET UP” screen must be set to other than “OFF”
(墌 pg. 24), or the “BAND” setting on the “MANUAL CH SET”
set to “CATV” (墌 pg. 23).
“DBS”: The “DBS SET UP” setting on the “STB SET” screen
must be set to other than “OFF” (墌 pg. 24).
“AUX”: Always selectable.
58
EN
TIMER RECORDING ON HDD/DVD DECK
CABLE/DBS
TV
DVD
When Programs Overlap Each Other
If “PROGRAM OVERLAPPED” appears, you have other programs
overlapping the program you have just made.
Confirm with the arrow on “MODIFY”, then press ENTER. Program
Overlap list appears.
Example: Five programs
overlap each other.
PROGRAM
ENTER
rtwe
2
1 Confirm the overlapping
programs. Overlapping programs
appear on the TV screen.
NOTE:
PROGRAM > CALENDAR PROG. (OVERLAP)
01/08/03 WED 10:30PM - 12:00AM DBS 100
GARDENING
[EDUCATION] FR360
5 PROGRAM OVERLAPPED
SELECT PROGRAM TO MODIFY
SELECT WITH [
]
THEN PRESS [ENTER]
PRESS [PROGRAM]
TO EXIT
10:30PM- DBS 100
D
W
PROGRAM
ENTER
D
9:00PM-
L-1
9:30PM- DBS 210
10:00PM-
TV 63
11:00PM- CATV 4
If you do not mind this overlap,
EXIT
SELECT
press PROGRAM to finish the timer
program setting. The program with
the lower program number will be recorded and the other one will not
be recorded correctly. If no changes are made for approximately 1
minute, the unit will return to the normal screen.
2 Press rt to select the desired program to be canceled or
changed, then press ENTER.
3 Perform “Cancel And Change Programs” (refer to left column).
NOTE:
Check Programs
To check the whole list of programs
1 Press PROGRAM to access the program top screen.
2 Press rtw e to select “PROGRAM LIST”, then press ENTER.
● The details of a selected program appear on the top of the screen.
● The daily program of a title is listed as one program.
To check the list of programs by date
1 Press PROGRAM to access the program top screen.
2 Press rtw e to select “CALENDAR LIST”, then press
ENTER.
3 Press rt to select the desired date, then press ENTER.
Cancel And Change Programs
● Repeat steps in “Check Programs” to select a program before
proceeding.
To cancel the program
1 Press rtw e to select “CANCEL”, then press ENTER.
To modify the program settings
1 Press rtw e to select “MODIFY”, then press ENTER.
2 Change the settings of the desired recording options as
required.
● Refer to steps 4 – 13 in “Manual Timer Programming” (墌 pg. 57).
To skip the weekly/daily programs to the next week/day
It is easy to temporarily cancel weekly/daily programs of a week/
day.
1 Press rtw e to select “PROGRAM SKIP”, then press ENTER.
2 Press w e to select “SKIP”, then press ENTER.
To save the titles of weekly/daily programs (HDD Deck Only)
Use this function to avoid overwriting titles of weekly/daily
programs of a previous week/day.
1 Press rtw e to select “TITLE SAVE”, then press ENTER.
2 Press w e to select “SAVE”, then press ENTER.
NOTE:
This function is available only when the remaining capacity of the hard
disc is sufficient.
Downloaded From DvDPlayer-Manual.com JVC Manuals
When any overlaps remain after deletion and modification of programs,
Program Overlap list remains showing the conflicting programs. In such
a case, repeat the procedure above until the conflict is solved.
TIMER RECORDING ON HDD/DVD DECK
Automatic Satellite Program Recording
(HDD Deck Only)
This function allows you to automatically record a satellite program
which is timer-programmed on your external DBS receiver.
Connect a DBS receiver to the unit’s [S-VIDEO/VIDEO/AUDIO
INPUT L-1] connectors and program the timer on the DBS
receiver. The unit starts or stops recording by the signals input
from the DBS receiver. After recording, the unit’s power shuts off
automatically.
● You can also connect the cable box if it has a timer.
59
● Make sure the DBS receiver is connected to the unit’s [S-VIDEO/
VIDEO/AUDIO INPUT L-1] connectors.
● Program the timer on the DBS receiver.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
1 Press HDD on the remote to choose the recording deck. You
can also press VHS/HDD/DVD SELECT on the unit repeatedly to
select the recording deck.
2 Press REC MODE repeatedly to set the recording mode.
3 Press and hold REC LINK for about 2 seconds to engage the
Automatic Satellite Program Recording mode. “
appear on the front display panel.
” and “R-LK”
NOTES:
ATTENTION:
● Be sure not to turn on the DBS receiver before the program is
executed; otherwise, the unit will start recording when the DBS
receiver’s power is turned on.
● If you have connected another appliance other than a DBS
receiver to the [S-VIDEO/VIDEO/AUDIO INPUT L-1] connectors,
be sure not to engage the Automatic Satellite Program Recording
mode; otherwise, the unit will start recording when the connected
appliance’s power is turned on.
● Automatic Satellite Program Recording and timer-recording cannot
be done at the same time.
VHS/HDD/DVD
SELECT
REC MODE
CABLE/DBS
TV
EN
DVD
HDD
REC MODE
REC LINK
Downloaded From DvDPlayer-Manual.com JVC Manuals
● To disengage the Automatic Satellite Program Recording mode,
press REC LINK.
● If the unit’s power is off, it is not possible to engage the Automatic
Satellite Program Recording mode.
” blinks quickly on the front display panel even though
● In step 3, if “
your DBS receiver’s power is off, Automatic Satellite Program
Recording will not work properly with that DBS receiver*. If this is the
case, perform “Manual Timer Programming” (墌 pg. 57) to
timer-record a satellite program.
* Some DBS receivers output signals even if the power is off. Automatic
Satellite Program Recording is not possible with those DBS receivers.
● “ ” blinks on the front display panel while Automatic Satellite
Program Recording is in progress.
● For timer programming of the DBS receiver, refer to the instruction
manual of the DBS receiver.
● Automatic Satellite Program Recording is not possible if your DBS
receiver does not have a timer.
● Pressing the unit’s 1 button while Automatic Satellite Program
Recording is in progress turns off the unit’s power and disengages
the Automatic Satellite Program Recording mode.
● If there are more than one satellite programs you wish to record with
Automatic Satellite Program Recording, it is not possible to set
different recording modes for each program.
● Depending on the type of DBS receiver, the unit may not record a
slight portion of the beginning of the program or may record slightly
longer than the actual length of the program.
● If you engage the Automatic Satellite Program Recording mode when
the DBS receiver’s power is on, the unit will not start Automatic
Satellite Program Recording even though “ ” blinks on the front
display panel. When the DBS receiver shuts off once and is turned
back on again, the unit starts recording.
● You can also record a program from your cable system in the same
way if the system has a timer.
60
EN
TIMER RECORDING ON VHS DECK
®
VCR Plus+ Timer Programming
You can program this unit to timer-record as many as 8 programs.
With the VCR Plus+ system, timer programming is greatly
simplified because each TV program has a corresponding code
number which your unit is able to recognize.
You can use the remote control to enter the PlusCode number.
●
●
●
●
Make sure that the unit’s built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
CABLE/DBS
TV
DVD
VHS TIMER
VHS
0-9
PROGRAM
rt
ENTER
REC MODE
1 Load a cassette with the record safety tab intact.
2 Press VHS so that the VHS lamp lights up on the unit.
3 Press PROGRAM to access the
4 Press rt to select “VCR
PLUS+ PRGM”, then press
ENTER.
PROGRAM
VCR PLUS+ PRGM
PROGRAM / CONFIRM
R,T THEN (ENTER)
(PROGRAM) TO END
5 Press the number keys to enter
the PlusCode number of a program
you wish to record, then press
ENTER.
PLUSCODE NO.
● If you have made a mistake, press
PRESS NUMBER KEY (0–9)
CANCEL and input the correct
PRESS (PROGRAM) TO END
number before you press ENTER.
VCR PLUS+ SYSTEM
● If the number you entered is invalid,
“ERROR” appears on the TV
screen and “Err” appears on the front display panel.
Press CANCEL and input a valid PlusCode number.
6 The PlusCode number you
entered and the matching timerrecording information are displayed
on the TV screen. Check the
program data.
● To cancel this setting, press
PROGRAM.
● To program another timer, repeat steps 3-8.
● If “PROGRAM NOT COMPLETED PROGRAM OVERLAP” appears
on the TV screen, see page 62.
9 Press VHS TIMER to engage the unit’s timer mode. The VHS
recording lamp lights up on the unit and the HDD or DVD deck is
automatically selected. When the HDD or DVD deck is in timer
standby mode, the unit is automatically turned off.
● To disengage the timer mode, press VHS TIMER again.
IMPORTANT:
If you have moved to a different area or if a broadcasting station’s
channel number has been changed, the wrong channel number will
be displayed on the VCR Plus+ program screen in step 6. When this
happens, set the correct Guide Channel number for that station.
®
(墌 pg. 86, “Changing VCR Plus+ Setting”)
NOTES:
CANCEL
Program screen.
7 Press REC MODE to select the desired recording mode.
8 Press ENTER to complete timer programming.
PROGRAM 1
(PLUSCODE NO. 12345678)
START
STOP
12:00 AM
1:00 AM
DATE
CH SP/EP
1/ 30/04
15
SP
PRESS (8=DAILY, 9=WEEKLY
R/T, REC MODE), THEN (ENTER)
(PROGRAM) TO END
IMPORTANT:
Make sure the channel position number you wish to record is
displayed; if not, see “Changing VCR Plus+® Setting” (墌 pg. 86) and
set
the Guide
Channel
number correctly.
Downloaded
From
DvDPlayer-Manual.com
JVC Manuals
● To Timer-Record Weekly Or Daily Serials:
— in step 6, press number key “9” for weekly serials or number key
“8” for daily serials (Monday - Friday). Either “WEEKLY” or “DAILY”
appears on the TV screen. Pressing the button again makes the
corresponding indication disappear.
● You can program this unit to timer-record as many as 8 programs. If
you try to program the unit to record a ninth, “PROGRAM FULL”
appears on the TV screen and “FULL” appears on the front display
panel. To record the extra program, you must first cancel any
unnecessary programs. (墌 pg. 62)
● To record the programs received by cable box or DBS receiver,
record on the HDD or the DVD discs. For details, refer to “VCR Plus+
C3® Timer Programming” (墌 pg. 55).
TIMER RECORDING ON VHS DECK
Manual Timer Programming
8 Press w e to select “DATE”, then press rt to set the desired
● The current date appears on the TV screen. The date you enter
appears in its place.
9 Press w e to select “CH”, then press rt to select the desired
channel.
10 Press REC MODE to select the desired recording mode. Or
CABLE/DBS
TV
● Each press of rt increases/decreases the stop time in 1-minute
interval.
● To increase/decrease the stop time in 30-minutes interval, press and
hold rt.
date.
Make sure that the unit’s built-in clock is set properly.
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
press w e to select “SP/EP”, then press rt to select the desired
recording mode.
DVD
VHS TIMER
VHS
11 Press ENTER to access the Program Check screen.
12 Press PROGRAM to complete timer programming.
0-9
ENTER
61
stop time.
You can program this unit to timer-record as many as 8 programs.
If you do not know the PlusCode number for the program you wish
to record, use the following procedure to set your unit to timerrecord the program.
●
●
●
●
EN
7 Press w e to select “STOP”, then press rt to set the desired
“PROGRAM COMPLETED” appears on the TV screen for about 5
seconds, then the normal screen appears. If “PROGRAM NOT
COMPLETED PROGRAM OVERLAP” appears on the TV screen,
see page 62.
PROGRAM
● To program another timer, repeat steps 3 - 12.
rtwe
13 Press VHS TIMER to engage the unit’s timer mode. The VHS
recording lamp lights up on the unit and the HDD or DVD deck is
automatically selected. When the HDD or DVD deck is in timer
standby mode, the unit is automatically turned off.
● To disengage the timer mode, press VHS TIMER again.
NOTES:
● To Timer-Record Weekly Or Daily Serials:
— anytime during steps 8 through 10, press number key “9” for
weekly serials or number key “8” for daily serials (Monday - Friday).
Either “WEEKLY” or “DAILY” appears on the TV screen. Pressing the
button again makes the corresponding indication disappear.
● You can program this unit to timer-record as many as 8 programs. If
you try to program the unit to record a ninth, “PROGRAM FULL”
appears on the TV screen. To record the extra program, you must
first cancel any unnecessary programs. (墌 pg. 62)
● In case of a power failure after programming, the unit’s memory
backup keeps your selections for approximately 5 seconds.
● Programs that start after midnight must have the next day’s date.
● To record the programs received by cable box or DBS receiver,
record on the HDD or the DVD discs. For details, refer to “Manual
Timer Programming” (墌 pg. 57).
REC MODE
1 Load a cassette with the record safety tab intact.
2 Press VHS so that the VHS lamp lights up on the unit.
3 Press PROGRAM to access the Program screen.
4 Press rt to select “PROGRAM/
PROGRAM
CONFIRM”, then press ENTER
access the Program Check screen.
VCR PLUS+ PRGM
PROGRAM / CONFIRM
R,T THEN (ENTER)
(PROGRAM) TO END
5 Press rt to select the blank
number, then press ENTER. The
program screen appears.
6 Press w e to select “START”,
then press rt to set the desired
start time.
● Each press of rt increases/
decreases the start time in 1-minute
interval.
● To increase/decrease the start time in
30-minutes interval, press and hold
rt.
PR START STOP CH
1
8:00P 10:00 12
2 10:00A 10:45 40
3 11:30P
1:00 125
4
5
6
7
8
(PROGRAM) TO END
DATE
12/24
12/25
12/25
PROGRAM 4
START
– –:– –AM
DATE
– –/– –/– –
STOP
– –:– –AM
CH SP/EP
– – – SP
PRESS (RTYU, 8=DAILY
9=WEEKLY), THEN (ENTER)
(PROGRAM) TO END
Downloaded From DvDPlayer-Manual.com JVC Manuals
62
EN
TIMER RECORDING ON VHS DECK
When Programs Overlap Each Other
CABLE/DBS
TV
VHS TIMER
VHS
If “PROGRAM NOT COMPLETED PROGRAM OVERLAP”
appears, you have another program overlapping the program you
have just made.
The Program Check screen appears and conflicting programs will
start blinking.
DVD
1
PR
1
2
3
4
5
6
7
8
CANCEL
PROGRAM
PROGRAM NOT COMPLETED
PROGRAM OVERLAP
ENTER
rtwe
(
START
8:00P
10:00A
11:30P
9:00P
STOP CH
10:00 12
10:45 40
1:00 125
10:00 10
DATE
12/24
12/25
12/25
12/24
)](ENTER) (PROGRAM) : END
Example: Program 1 (you have just made) and Program 4
overlap each other.
1 Confirm the overlapping programs. Overlapping programs blink
on the TV screen.
2 Press rt to select the program to modify, then press ENTER
or e.
● You can only select one of the overlapping programs.
NOTE:
If you do not mind this overlap, press PROGRAM to finish the timer
program setting. The program with the lower program number will be
recorded and the other one will not be recorded correctly. If no changes
are made for approximately 1 minute, the unit will return to the normal
screen.
Check, Cancel And Change Programs
1 When the VHS recording lamp (7) lights up on the unit
3 Press rt to select the desired program to be canceled or
changed.
Press VHS TIMER, then press DVD (1).
When the VHS lamp does not light up on the unit
Press VHS so that the VHS lamp lights up on the unit.
2 Press PROGRAM to access the
Program screen.
3 Press rt to select “PROGRAM/
CONFIRM”, then press ENTER to
access the Program Check screen.
PR START STOP CH
1
8:00P 10:00 12
2 10:00A 10:45 40
3 11:30P
1:00 125
4
5
6
7
8
(PROGRAM) TO END
4 Press rt to select the program,
then press ENTER. The program
screen appears.
To cancel a program
Press CANCEL.
DATE
12/24
12/25
12/25
PROGRAM 4
START
8:00AM
DATE
12/24/04
FRI
STOP
10:00AM
CH SP/EP
12
SP
PRESS (CANCEL) TO CANCEL
PRESS (ENTER) TO CONFIRM
(PROGRAM) TO END
5 Change the settings of the desired recording options as
required.
● Refer to steps 6 - 11 in “Manual Timer Programming” (墌 pg. 61).
6 Press PROGRAM to complete timer correction. The previous
screen resumes.
7 Press VHS TIMER.
● The VHS recording lamp lights up on the unit and the HDD or DVD
deck is automatically selected. When the HDD or DVD deck is in
timer standby mode, the unit is automatically turned off.
Downloaded From DvDPlayer-Manual.com JVC Manuals
To cancel the program
Press CANCEL.
● “PROGRAM COMPLETED” appears on the TV screen for about 5
seconds, then the normal screen resumes.
To change the program setting
Press ENTER, then go to step 4.
4 Change the program setting.
● Refer to steps 6 - 11 in “Manual Timer Programming” (墌 pg. 61).
5 Press PROGRAM to access the Program screen, then press
rt to select “PROGRAM/CONFIRM” to check if the conflict has
been settled.
Program check screen appears.
● “PROGRAM COMPLETED” appears on the TV screen for about 5
seconds, then the normal screen resumes.
6 Press VHS TIMER.
NOTE:
When any overlaps remain after deletion and modification of programs,
Program Check screen remains showing the conflicting programs. In
such a case, repeat the procedure above until the conflict is solved.
NAVIGATION ON HDD/DVD DECK
Library Database Navigation
The Library Database Navigation enables you to search and select
the desired titles recorded on the HDD deck and the DVD deck
very easily.
You can record up to 99 titles on a disc.
Each time a title is recorded, the information of the title is
registered for the Library Database Navigation automatically.
So, you can confirm the information of the titles recorded with the
Library Database Navigation screen. And, you can also select one
of the titles recorded using the Library Database Navigation.
The following screen appears as the Library Database Navigation
screen when you press NAVIGATION. You can move the arrow to
select the desired position on the screen by pressing rt w e on
the remote control.
NAVIGATION > ORIGINAL
A
0026 [FISH WORLD
25/12/03 THU 10:00 - 10:15
FROG WORLD
]
143 MIN
PR. 3
[HOBBY] EP
D
SELECT WITH [
]
THEN PRESS [ENTER]
B
PRESS [NAVIGATION]
TO EXIT
NAVIGATION
ENTER
EXIT
SELECT
C
E
F
G
A Playback screen
(Indicates currently received TV program.)
B Guidance for operations
C Scroll bar
(Appears when there are over nine registered titles (or play
lists). The scroll bar only indicates that there are more titles (or
play lists) hidden off the current screen display. To show hidden
titles (or play lists), press rt w e repeatedly.)
D Recording information for the title indicated by the arrow
E Index list
(Thumbnail still of each title)
Thumbnail still is not to be played back.
F Index
: Indicates no index is registered.
: Indicates title in standby for timer recording.
: Indicates no title is registered.
G Icons
(Indicate the record condition of each title.)
The Icons and their meanings
This title is write-protected.
This title was recorded with timer recording.
W
This title is Weekly Recording/Weekly Overwrite.
D
This title is Daily Recording/Daily Overwrite.
D
This title is Daily Recording/Weekly Overwrite.
NEW
EN
63
Using Library Database Navigation system, you can easily modify
registered information, edit the title or play list, as well as search
for the beginning of each title.
This title has not been played back.
This title is copy-protected.
This title can only be recorded once (copy-once
title).
Downloaded From DvDPlayer-Manual.com JVC Manuals
About registration of information
The following information is automatically registered for each title
when ordinary recording or timer recording is performed, then
stored in an area specified on the unit.
●
●
●
●
●
●
●
index* (reduced pictures to show program titles)
program title*
category*
date and time
channel
recording mode
length of recording time
The items marked with an asterisk (*) can be easily modified and
registered again after recording by using Library Database
Navigation system.
The limitations of registration
You can register information up to 99 titles for the DVD deck and
200 titles for the HDD deck.
When the amount of information is at the limits of registration, you
cannot record new titles any more. In this case, you need to delete
old titles to register new one. (墌 pg. 65)
NOTES:
● Once a DVD-R/RW (Video mode) disc has been finalized, the
displays for original and play list do not appear. Only display for
library appears.
● When you move the title recorded on HDD to DVD, the icon will be
changed to .
● Sound of received channel may be interrupted while the Library
Database Navigation screen is displayed.
● The order of index which are displayed by pressing DUBBING differs
from the images displayed by pressing NAVIGATION or EDIT.
● You cannot perform timer recording during editing of thumbnail
images or play lists by pressing EDIT. Press EDIT to clear the Editing
screen before performing timer recording.
64 EN NAVIGATION ON HDD/DVD DECK
Scan For Beginning Of Title
●
●
●
●
Modify Original Information
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
Press HDD or DVD to choose the corresponding deck.
Load a DVD disc to scan.
●
●
●
●
CABLE/DBS
TV
HDD
DVD
DVD
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
Press HDD or DVD to choose the corresponding deck.
Load a DVD disc to modify.
ATTENTION:
CANCEL
ENTER
● It is not possible to modify discs recorded on DVD units from other
manufacturers.
● You cannot perform timer recording during editing the index by
pressing EDIT. Press EDIT to clear the editing screen before
performing timer recording.
MEMO
NAVIGATION
rtwe
Modify Index
1 Press EDIT. The Editing screen appears.
2 (DVD deck only) Press rt w e to select “MODIFY” under
4
8
9
“ORIGINAL/PLAY LIST”, then press ENTER.
3 Press rt w e to select “MODIFY” under “ORIGINAL”, then
press ENTER.
4 Press rt w e to select one title you want to modify, then press
ENTER.
5 Press w e to select “INDEX”.
6 Search for the picture from the
You can scan the beginning of the title easily with the Library
Database Navigation.
1 Press NAVIGATION. The Library Database Navigation screen
appears.
2 Press rt w e to select “ORIGINAL”, then press ENTER.
3 Press rt w e to select the
0026 [FISH WORLD
]
12/26/02 THU 10:00AM - 10:15AM
FROG WORLD
143 MIN
TV 3 S
[HOBBY] EP
SELECT WITH [
]
● When you want the plural titles to
THEN PRESS [ENTER]
be played back continuously,
PRESS [NAVIGATION]
TO EXIT
press MEMO after selecting the
desired title. The numbers of the
ENTER
NAVIGATION
playback order appear on the
EXIT
SELECT
index. You can select up to 8 titles.
● When you want to correct the
order, move the arrow to the desired index and press MEMO. The
number disappears and the unit re-numbers the other programs
automatically.
● When you want to cancel the order, press CANCEL (&).
4 Press w e to select
NAVIGATION > ORIGINAL
“BEGINNING”, then press ENTER.
● To resume playback from the point
where playback was previously
stopped, press w e to select
“RESUME”, then press ENTER.
● To repeat playback of a selected
title, press w e to select
“REPEAT”, then press ENTER.
12/26/02 THU
10:00AM - 10:15AM TV
FROG WORLD
SP
3S
[HOBBY]
SELECT WITH [
]
THEN PRESS [ENTER]
SELECT HOW TO PLAY BACK
PRESS [NAVIGATION]
TO EXIT
NAVIGATION
ENTER
EXIT
SELECT
BEGINNING
RESUME
5 Press 9 to pause playback.
● To resume normal playback, press 4.
6 Press 8 to stop playback.
Downloaded From DvDPlayer-Manual.com JVC Manuals
7 Confirm the arrow is on
12/26/02 THU 10:00AM - 10:15AM
FROG WORLD
REPEAT
TV 3 S
[OTHERS] SP
INDEX
PROG. 1
0 : 01 : 03
SELECT IMAGE TO REPLACE WITH
“REPLACE”, then press ENTER
to register new index. New index
appears on the right window.
NAVIGATION > ORIGINAL
index (small pictures) of the
desired title, then press ENTER.
EDITING > MODIFY INDEX
title by pressing the appropriate
buttons (3, 4, 5, or 9). The
pictures of the title appear on the
left window.
ON REMOTE
REPLACE
RETURN
● When you press ENTER with the arrow on “RETURN” you can return
to the previous screen.
8 Press EDIT to return to the normal screen.
Modify Title Name
1 Perform steps 1 – 4 of “Modify Index” (墌 pg. 64) before
continuing.
2 Press rt w e to select “NAME”, then press ENTER.
3 Press rt w e to select the
desired letter or command, then
press ENTER. Repeat this
process to complete the name.
● To correct a letter, press rt w e
to select “DELETE”, then press
ENTER.
● You can enter the letters up to 64.
ABC
EDITING > MODIFY NAME
0026 [FISH WORLD
]
12/26/02 THU 10:00AM - 10:15AM
FROG WORLD
64 MIN
TV 3 S
[HOBBY] XP
F R O G WO R L D
SELECT WITH [
]
THEN PRESS [ENTER]
PRESS [EDIT]
TO EXIT
EDIT
ENTER
EXIT
SELECT
4 Press rt w e to select
“SAVE”, then press ENTER.
5 Press EDIT to return to the normal screen.
A
B
a
b
G
H
I
J
K
L
g
h
i
j
M
N
O
P
Q
R
m
n
o
p
q
S
T
U
C
D
V
W X
s
t
u
v
w
x
Y
Z
y
z
!
"
#
$
;
<
>
?
@
[
'
(
)
,
\
]
^
_
`
{
CANCEL
E
F
% &
.
:
c
DELETE
d
e
k
f
1
2
3
l
4
5
6
r
7
8
9
0
+
-
*
/
=
|
}
~
SAVE
NAVIGATION ON HDD/DVD DECK
65
Delete Unwanted Part Of The Title (DVD deck only)
Modify Category
1 Perform steps 1 – 4 of “Modify Index” (墌 pg. 64) before
You can delete unwanted part of the title.
1 Perform steps 1 – 3 of “Modify Index” (墌 pg. 64) before
continuing.
2 Press rt w e to select “CATEGORY”, then press ENTER.
3 Press rt w e to select the
continuing.
EDITING > MODIFY CATEGORY
desired category, then press
ENTER.
0026 [FISH WORLD
]
12/26/02 THU 10:00AM - 10:15AM
FROG WORLD
4 Press EDIT to return to the
SELECT WITH [
]
THEN PRESS [ENTER]
normal screen.
PRESS [EDIT]
TO EXIT
EDIT
ENTER
EXIT
SELECT
EN
64 MIN
TV 3 S
[HOBBY] XP
MOVIE
MUSIC
DRAMA
ANIMATION
SPORTS
DOCUMENTARY
NEWS
WEATHER
EDUCATION
HOBBY
ENTERTAINMENT
ART
want to delete, then press ENTER.
4 The playback pictures appear in the window on the screen. The
elapsed playing time starts counting with the arrow on “IN”.
5 Find the point where you want
the deletion to begin, then press
ENTER with the arrow on “IN”.
The edit-in time is fixed and the
elapsed playing time starts
counting again.
Protect Title (DVD deck only)
You can protect titles to prevent accidental erasure of the
important titles.
6 Find the point where you want
1 Perform steps 1 – 3 of “Modify Index” (墌 pg. 64) before
continuing.
2 Press rt w e to select “PROTECT”, then press ENTER.
3 Press rt w e to select a title you want to protect, then press
ENTER.
4 Press w e to select “PROTECT”, then press ENTER. “
2 Press rt w e to select “DEL SCENE”, then press ENTER.
3 Press rt w e to select one title whose unwanted part you
”
appears.
● To cancel the protection, repeat 3 – 4 again. In step 4, select
“CANCEL PROTECT”, then press ENTER.
5 Press EDIT to return to the normal screen.
NOTE:
All the titles on a disc will be deleted once the disc is formatted even if
they are protected titles. (墌 pg. 65)
EDITING > ORIGINAL/DELETE SCENE
12/22/02 SUN 5:30AM - 8:00AM
RALLY CAR
TV 12 S
[OTHERS] SP
IN
0 : 05 :15
OUT
0 : 06 :15
PROG. 1
0 : 01 : 03
SELECT IMAGE TO REPLACE WITH
IN
OUT
ON REMOTE
PREVIEW
OK
the deletion to end, then press
ENTER with the arrow on “OUT”.
The edit-out time is fixed.
● Press 3, 4, 5, 2, 6 or 9 to find the edit-in and edit-out
points.
7 Press w e to select “PREVIEW”, then press ENTER to preview
the edited title.
8 Press w e to select “OK”, then press ENTER.
● If you do not want to delete the scene, press EDIT or RETURN.
To modify the points
A Press EDIT or RETURN.
B Repeat steps 4 – 8 as necessary.
9 Press w e to select “DELETE”, then press ENTER. The
selected scene is deleted.
Delete Title
● To cancel the deletion, press w e to select “CANCEL”, then press
ENTER.
You cannot record any more with Library Database Navigation
once the registered titles on the disc reach 99 titles for the DVD
deck and 200 titles for the HDD deck. Deleting unnecessary titles
after dubbing or other operations can increase remaining time and
available recording capacity. (For DVD-R discs, although it is
possible to delete recorded titles, available recording capacity
does not increase.) The deleted title is never resumed. Play lists
and title information in the unit’s library are also deleted.
10 Press EDIT to return to the normal screen.
1 Press EDIT. The Editing screen appears.
2 Press rt w e to select “DELETE” under “ORIGINAL”, then
press ENTER.
3 Press rt w e to select one title you want to delete, then press
ENTER.
4 Press w e to select “DELETE”, then press ENTER.
● When you cancel the deletion, select “CANCEL”, then press ENTER.
5 Press EDIT to return to the normal screen.
Downloaded From DvDPlayer-Manual.com JVC Manuals
NOTES:
● There may be a discrepancy of several seconds between the scene
you intend to edit, and the scene which is actually edited.
● Available recording capacity may not match the deleted part after
deletion.
66 EN NAVIGATION ON HDD/DVD DECK
Divide Title (HDD deck only)
Modify Play List Information
1 Press EDIT. The Editing screen appears.
2 Press rt w e to select “DIVIDE”, then press ENTER.
3 Press rt w e to select a title to divide, then press ENTER.
4 Press 4, and press 3 or 5 to locate a point to divide, then
press 9.
5 Confirm the arrow is on “DIVIDE”, then press ENTER at the
dividing point.
● The first picture (start) of the newly created title appears in the
bottom right window.
6 Press w e to select “PREVIEW”, then press ENTER.
● The first several seconds of the newly created title is played back,
then the playback pauses at the dividing point.
● To undo the division, press w e to select “RETRY”, then press
ENTER. Repeat the above procedure to locate another point to
divide.
●
●
●
●
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
Press HDD or DVD to choose the corresponding deck.
Load a DVD disc to modify.
ATTENTION:
● It is not possible to modify discs recorded on DVD units from other
manufacturers.
● You cannot perform timer recording during editing the index by
pressing EDIT. Press EDIT to clear the editing screen before
performing timer recording.
7 Press w e to select “OK”, then press ENTER.
8 Press EDIT to return to the normal screen.
CABLE/DBS
TV
NOTE:
There may be a discrepancy of several seconds between the scene
you intend to edit, and the scene which is actually edited.
HDD
DVD
DVD
Modify Chapter
You can create and delete chapter marks in titles.
CANCEL
1 Perform steps 1 – 4 of “Modify Index” (墌 pg. 64) before
continuing.
2 Press rt w e to select “CHAPTER”, then press ENTER.
3 Confirm the arrow is on
ENTER
MEMO
EDIT
NAVIGATION
rtwe
EDITING > MODIFY CHAPTER
“MARK”, then press ENTER at
positions you want to mark.
● The newly created chapter is
displayed.
● To undo the marking, press w e
to select “RETRY”, then press
ENTER. Repeat the above
procedure to locate another point
to mark.
CHAPTER 03/10
0 : 07 : 01
2
3
8
01 00 : 00 : 00
MARK
02 00 : 05 : 30
03 00 : 07 : 00
ERASE
RETRY
6
4
5
9
04 00 : 30 : 00
RETURN
4 Press 4, and press 3 or 5 to select one chapter you want
to delete, then press 9.
5 Press w e to select “ERASE”, then press ENTER.
● The selected chapter is deleted.
● To undo the deletion, press w e to select “RETRY”, then press
ENTER. Repeat the above procedure to locate another point to
delete.
6 Press EDIT to return to the normal screen.
NOTE:
There may be a discrepancy of several seconds between the scene
you intend to edit, and the scene which is actually edited.
Downloaded From DvDPlayer-Manual.com JVC Manuals
Play List
It is a collection of the scenes. A play list can be freely edited and
played back without ever changing any original recording data.
Using the random access of a disc (which allows video data to be
instantly read no matter where it is on the disc), a play list includes
information such as the timer counter for the playback start point
and end point, indexes for checking the contents of recorded data,
category information, and more. Playback according to a play list
you have created allows you to enjoy various combinations of
video images from a single title.
NAVIGATION ON HDD/DVD DECK
Create Play List
Add scenes
1 Press EDIT. The Editing screen appears.
2 (DVD deck only) Press rt w e to select “MODIFY” under
1 Perform steps 1 – 4 in “Edit Scenes” (墌 pg. 67) before
continuing.
included in a play list, then press ENTER.
Move Scenes
5 The playback pictures appear in the window on the screen. The
1 Perform steps 1 – 4 of “Edit Scenes” (墌 pg. 67) before
elapsed playing time starts counting with the arrow on “IN/OUT”.
the created play list to begin, then
press ENTER with the arrow on
“IN/OUT”. The edit-in time is fixed
and the elapsed playing time
starts counting again.
7 Find the point where you want
the created play list to end, then
press ENTER with the arrow on
“IN/OUT”. The edit-out time is fixed.
EDITING > PLAY LIST/CREATE
TOTAL
SCENE
00 : 00 : 00
PAGE
1/1
1 PRO. 1
2
3
4
PRO. 1
6
7
8
IN
continuing.
2 Press rt w e to select “MOVE”, then press ENTER.
3 Press rt to select a scene to move, then press ENTER.
4 Press rt to select another scene to which the scene is to be
moved, then press ENTER.
5
0 : 00 :15
67
2 Press rt w e to select “SEL. TITLE”, then press ENTER.
3 Perform steps 4 – 10 in “Create Play List” (墌 pg. 67).
“ORIGINAL/PLAY LIST”, then press ENTER.
3 Press rt w e to select “CREATE”, then press ENTER.
4 Press rt w e to select a title that includes scenes to be
6 Find the point where you want
EN
TO
IN/OUT
MODIFY
MOVE
PREVIEW
SEL. TITLE
DELETE
RETRY
OK
● Press 3, 4, 5, 2, 6 or 9 to find the edit-in and edit-out
points.
● The edit-out point must come after the edit-in point.
8 Press rt w e to select “PREVIEW”, then press ENTER to
preview the play list.
9 Press rt w e to select “OK”, then press ENTER. The play list
is created.
To modify the points
A Press w e to select “MODIFY”, then press ENTER.
B Repeat steps 5 – 9 as necessary.
10 Press w e to select “EXIT”, then press ENTER to return to the
normal screen.
NOTES:
● There may be a discrepancy of several seconds between the scene
you intend to edit, and the scene which is actually edited.
● The title, index and category of the play list can be modified in the
same way as “ORIGINAL”. (墌 pg. 64)
● You can modify the play list that has just been created here by
adding, moving, or deleting unwanted parts to create a digest edition,
etc.
Edit Scenes
1 Press EDIT. The Editing screen appears.
2 (DVD deck only) Press rt w e to select “MODIFY” under
“ORIGINAL/PLAY LIST”, then press ENTER.
3 Press rt w e to select “MODIFY” under “PLAY LIST”, then
press ENTER.
4 Press rt w e to select a play list to modify, then press
ENTER.
5 Press rt w e to select “SCENE”, then press ENTER.
6 Press rt w e to select “MODIFY”, then press ENTER.
7 Press rt w e to select a scene to modify, then press ENTER.
8 Perform steps 5 – 10 in “Create Play List” (墌 pg. 67).
Downloaded From DvDPlayer-Manual.com JVC Manuals
● To cancel the move, press rt w e to select “RETRY”, then press
ENTER.
5 Perform steps 8 – 10 in “Create Play List” (墌 pg. 67).
Delete Scenes
1 Perform steps 1 – 4 of “Create Play List” (墌 pg. 67) before
continuing.
2 Press rt w e to select “DELETE”, then press ENTER.
3 Press rt to select a scene to delete, then press ENTER.
4 Perform steps 8 – 10 in “Create Play List” (墌 pg. 67).
Play Back Play List
1 Press NAVIGATION. The Library Database Navigation screen
appears.
2 Press rt w e to select “PLAY LIST”, then press ENTER.
3 Press rt w e to select the
NAVIGATION > PLAY LIST
index (small pictures) of the
desired play list, then press
ENTER.
]
0026 [FISH WORLD
026 CREATED 26/12/03 FRI
TEDDY BEAR 25/12
001
143 MIN
[MOVIE]
002
003
SELECT WITH [
]
THEN PRESS [ENTER]
● When you want the plural play lists
PRESS [NAVIGATION]
TO EXIT
to be played back continuously,
press MEMO after selecting the
ENTER
NAVIGATION
EXIT
SELECT
desired play lists. The numbers of
the playback order appear on the
index. You can select up to 30 play lists.
● When you want to correct the order, move the arrow to the desired
index and press MEMO. The number disappears and the unit renumbers the other play lists automatically.
● When you want to cancel the order, press CANCEL (&).
004
005
006
007
008
009
4 Press w e to select “BEGINNING”, then press ENTER. The
playback starts.
5 Press 9 to pause playback.
● To resume normal playback, press 4.
6 Press 8 to stop playback.
68 EN NAVIGATION ON HDD/DVD DECK
Delete Play List
1 Press EDIT. The Editing screen appears.
2 (DVD deck only) Press rt w e to select “MODIFY” under
Modify Library Information
“ORIGINAL/PLAY LIST”, then press ENTER.
3 Press rt w e to select “DELETE” under “PLAY LIST”, then
press ENTER.
4 Press rt w e to select one play list you want to delete, then
press ENTER.
5 Press w e to select “DELETE”, then press ENTER.
● When you cancel the deletion, select “CANCEL”, then press ENTER.
6 Press EDIT to return to the normal screen.
NOTE:
Title information can be registered in the unit’s memory for up to
600 DVD discs, 2,000 titles. It is helpful when finding a desired title
(or play list) by sorting according to the sort options registered
during (or after) recording.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press HDD or DVD to choose the corresponding deck.
Even if a play list is deleted, the titles recorded and the library
information are not affected at all.
CABLE/DBS
TV
Modify Index
HDD
DVD
DVD
A Perform steps 1 – 4 of “Edit Scenes” (墌 pg. 67) before
continuing.
B Perform steps 5 – 8 of “Modify Index” (墌 pg. 64).
Modify Play List Name
A Perform steps 1 – 4 of “Edit Scenes” (墌 pg. 67) before
continuing.
B Perform steps 2 – 5 of “Modify Title Name” (墌 pg. 64).
NAVIGATION
ENTER
rtwe
Modify Category
A Perform steps 1 – 4 of “Edit Scenes” (墌 pg. 67) before
continuing.
B Perform steps 2 – 4 of “Modify Category” (墌 pg. 65).
Scan For Title From Library
1 Press NAVIGATION. The Library Database Navigation screen
appears.
2 Press rt w e to select the
appropriate sort button to sort the
information, then press ENTER.
“DATE” : Sort by date
“DISC No.” : Sort by disc number
“CATEGORY” : Sort by category
“NAME” : Sort by name
● “DATE” and “DISC No.” are
available for the DVD deck only.
NAVIGATION
DVD NAVIGATION
ORIGINAL
PLAY LIST.
SELECT WITH [
]
THEN PRESS [ENTER]
PRESS [NAVIGATION]
TO EXIT
DVD LIBRARY
DATE
NAVIGATION
ENTER
EXIT
SELECT
CATEGORY
DISC No.
A
NAME
3 Press rt w e to select the desired title, then press ENTER.
● Playback begins automatically after the selected title is located.
NOTE:
If a disc registered in the library is recorded or modified on DVD units
from other manufacturers, it may become impossible to operate
properly.
Register Disc
When a disc that is not registered in the library is loaded, a
message appears confirming if the disc should be registered. If
registering, perform the following procedure.
1 Press w e to select “REGISTER”, then press ENTER to confirm
the registration.
2 Press NAVIGATION to return to the normal screen.
NOTES:
● It is not possible to register discs formatted on devices other than
JVC’s DVD recorders.
● It is not possible to register discs recorded on devices other than
JVC’s DVD recorders.
● It is not possible to register discs when “SAVE AS LIBRARY” is set to
“OFF”. (墌 pg. 82)
Downloaded From DvDPlayer-Manual.com JVC Manuals
NAVIGATION ON HDD/DVD DECK
Playback With MP3/WMA/JPEG
Navigation
EN
69
Locating The Desired Group And Tracks
1 Load a disc.
2 Press NAVIGATION.
3 Press rt w e to select “ORIGINAL”, then press ENTER.
4 Press rt to select the desired
NAVIGATION > ORIGINAL
group, then press ENTER.
This unit can play back discs that MP3/WMA sound files and JPEG
image files taken with digital still cameras or other devices are
recorded.
The MP3/WMA/JPEG Navigation enables you to search and select
the desired files recorded on CD-R/RW or CD-ROM discs very
easily.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press DVD to select the DVD deck.
● A list of files in the selected group
appears.
5 Press rt to select the desired
item, then press ENTER. The unit
starts playback from the selected
item.
● The unit stops when all items in
the selected group are played
back.
NOTES:
NAVIGATION > ORIGINAL
GROUP : 001/100
IT’S SHOWTIME ! ! /B’z
TRACK : 001/100
0 : 07 : 01
ROOT
001. IT’S SHOWTIME ! ! /B’z
CLASSIC
002. ONLY FLOWER IN THE WORLD/SMAP
CLUB
003. SEXY GUY/GOMAKI
DANCE
004. HEY?/AYAYA
EUROPE
005. DOOR TO TOMORROW/I WISH
FOREIGN GROUP
006. REASON/ASAMI
FOREIGN ROCK
007. DIE ANOTHER DAY/JAMES BOND
A Selected group number/total number of groups on the disc
B Selected file number/total number of files in the group that
contains the selected file
C Elapsed time (MP3 only)
D Name of the selected file
E Group name
F Selected file
NOTE:
If there are more than 100 files, the rest of the files are not
displayed. In this case, press ON SCREEN to display them on the
TV screen.
Downloaded From DvDPlayer-Manual.com JVC Manuals
GROUP : 001/100
IT’S SHOWTIME ! ! /B’z
TRACK : 001/100
0 : 07 : 01
ROOT
001. IT’S SHOWTIME ! ! /B’z
CLASSIC
002. ONLY FLOWER IN THE WORLD/SMAP
CLUB
003. SEXY GUY/GOMAKI
DANCE
004. HEY?/AYAYA
EUROPE
005. DOOR TO TOMORROW/I WISH
FOREIGN GROUP
006. REASON/ASAMI
FOREIGN ROCK
007. DIE ANOTHER DAY/JAMES BOND
NAVIGATION > ORIGINAL
GROUP : 001/100
IT’S SHOWTIME ! ! /B’z
TRACK : 001/100
0 : 07 : 01
ROOT
001. IT’S SHOWTIME ! ! /B’z
CLASSIC
002. ONLY FLOWER IN THE WORLD/SMAP
CLUB
003. SEXY GUY/GOMAKI
DANCE
004. HEY?/AYAYA
EUROPE
005. DOOR TO TOMORROW/I WISH
FOREIGN GROUP
006. REASON/ASAMI
FOREIGN ROCK
007. DIE ANOTHER DAY/JAMES BOND
● If you press SELECT(4) instead
of ENTER in step 4, the unit starts playback from the first file of the
group.
● JPEG files are played back as a slide show at the set intervals.
(墌 pg. 39)
● If a file name includes any 2-byte character, the unit may not show
the file name correctly.
● The order of the groups and items shown in steps 4 and 5 may differ
from the order shown on your PC.
70
EN
EDITING
6 Press w e to select “EXECUTE”, then press ENTER. The
Dubbing
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
CABLE/DBS
TV
HDD
VHS
DVD
DVD
dubbing screen appears for 5 seconds. To display the dubbing
screen again, press ON SCREEN.
EXECUTE: Select this to continue the dubbing operations.
CANCEL: Select this to cancel dubbing operation.
NOTES:
● Play lists are dubbed as programs.
● In Video mode, if the selected play list includes the scenes recorded
in the different transfer rate, the dubbing is performed in the highest
transfer rate of the scenes in the selected play list.
● During dubbing, it is not possible to play back on HDD or DVD, or to
set timer programming.
Just Dubbing (From HDD To DVD)
MARK
DUBBING
ENTER
rtwe
4
7
8
9
ON SCREEN
By using Just Dubbing function, when dubbing all selected original
recordings and/or play lists, the unit automatically sets the
appropriate recording mode depending on the combination of the
total time of the selected recordings and/or play lists to be dubbed
and the available disc space.
1 Load a recordable disc.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “HDD ]DVD”, then press ENTER.
4 Press rtw e to select “JUST”, then press ENTER.
5 Perform steps 5 – 6 of “High Speed Dubbing (From HDD To
DVD)”.
NOTES:
NOTES:
● It is not possible to dub simultaneously when timer programming is
set. Select either dubbing or timer programming.
● The order of the index which are displayed by pressing DUBBING
differs from the images displayed by pressing NAVIGATION or EDIT.
● Play lists are dubbed as programs.
● In Video mode, if the selected play list includes the scenes recorded
in the different transfer rate, the dubbing is performed in the highest
transfer rate of the scenes in the selected play list. However, the
lower transfer rate cannot be dubbed in the higher transfer rate.
● The recordable time of the disc is displayed on the bar meter. For
details, refer to “About Disc Remaining Display” (墌 pg. 73).
● During dubbing, it is not possible to play back on HDD or DVD, or to
set timer programming.
High Speed Dubbing (From HDD To DVD)
Manual Dubbing (From HDD To DVD)
It is possible to dub the original recordings and/or play lists on the
HDD deck to DVD discs. The dubbing is performed in high speed,
keeping the original transfer rate.
It is possible to perform dubbing in the desired transfer rate.
AUDIO
NOTES:
● After accessing the Dubbing Menu screen, it is not possible to take
out a disc.
● It is not possible to dub copy-once titles in Video mode.
● When dubbing a copy-once title, the data will be moved from HDD to
DVD upon completing dubbing.
● When you cancel dubbing a copy-once title during dubbing, the
original recording on the HDD deck remains and the title copied to a
DVD disc is deleted.
● It is not possible to dub play lists which contain copy-once titles.
● It is not possible to dub the following programs to DVD-R/RW disc
(Video mode):
●
●
●
●
which contains more than one audio language.
which is on the play list.
which is edited (also Live Memory Recording).
which is recorded in LP mode or FP155-FP240 mode.
● Recording may not be performed in the highest speed depending on
the characteristics of the disc used.
1 Load a recordable disc.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “HDD ]DVD”, then press ENTER.
4 Press rtw e to select “HIGH SPEED”, then press ENTER.
5 Press rtw e to select indexes (small pictures) of desired
original recordings and/or play lists, then press MARK. After
selecting all indexes you want to dub, press ENTER.
● You can select up to 8 original recordings and/or play lists.
● The recordable time of the disc is displayed on the bar meter. For
details, refer to “About Disc Remaining Display” (墌 pg. 73).
Downloaded From DvDPlayer-Manual.com JVC Manuals
1 Load a recordable disc.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “HDD ]DVD”, then press ENTER.
4 Press rtw e to select “MANUAL”, then press ENTER.
5 Perform step 5 of “High Speed Dubbing (From HDD To DVD)”.
The Manual Dubbing screen appears.
6 Press rt to select “REC MODE”, then press ENTER. Press
rt to select the desired option, then press ENTER.
7 Press rt to select “CONFIRM”, then press ENTER. The
confirmation screen appears.
8 Press w e to select “EXECUTE”, then press ENTER. The
dubbing screen appears for 5 seconds. To display the dubbing
screen again, press ON SCREEN.
EXECUTE: Select this to continue the dubbing operations.
CANCEL: Select this to cancel dubbing operation.
NOTES:
● In Video mode, if the selected play list includes the scenes recorded
in the different transfer rate, the dubbing is performed in the highest
transfer rate of the scenes in the selected play list. However, the
lower transfer rate cannot be dubbed in the higher transfer rate.
● The recordable time of the disc is displayed on the bar meter. For
details, refer to “About Disc Remaining Display” (墌 pg. 73).
● During dubbing, it is not possible to play back on HDD or DVD, or to
set timer programming.
EDITING
EN
71
Dubbing From HDD To VHS
Dubbing From DVD To VHS
It is possible to perform dubbing from the HDD deck to the VHS
deck.
It is possible to perform dubbing from the DVD deck to the VHS
deck.
1 Load a cassette with the record safety tab intact.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “HDD ]VHS”, then press ENTER.
4 Press rtw e to select indexes (small pictures) of desired
1 Load the disc you want to dub onto the DVD deck, and a
original recordings and/or play lists, then press MARK. After
selecting all indexes you want to dub, press ENTER.
● You can select up to 8 original recordings and/or play lists.
5 Press rt to select “SELECT RECORDING MODE”, then press
ENTER. Press rt to select the desired option (SP or EP), then
press ENTER. The confirmation screen appears.
6 Press rt to “SELECT SOUND MODE”, then press ENTER.
Press rt to select the desired option (L/R, L, R or NORM), then
press ENTER. The confirmation screen appears.
7 Press t to select “CONFIRM”, then press ENTER.
8 Press VHS so that the VHS lamp lights up on the unit.
The current display on the screen will be switched to a receiving
broadcast display.
9 While holding 7, press 9 so that the VHS deck enters the
record pause mode.
10
Press HDD so that the HDD lamp lights up on the unit.
The dubbing screen will appear.
11
Press w e to select “EXECUTE”, then press ENTER for
confirmation.
● To cancel the dubbing, press the 8 then w e to select “CANCEL”
and press ENTER to confirm.
Original Dubbing (From DVD To HDD)
It is possible to dub the original recordings on DVD discs to the
HDD deck.
1 Load a disc you want to dub.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “DVD ]HDD”, then press ENTER.
4 Press rtw e to select “TITLE”, then press ENTER.
5 Press rtw e to select indexes (small pictures) of desired
original recordings and/or play lists, then press MARK. After
selecting all indexes you want to dub, press ENTER.
● You can select up to 8 original recordings and/or play lists.
6 Press w e to select “EXECUTE”, then press ENTER to start
dubbing.
EXECUTE: Select this to continue the dubbing operations.
CANCEL: Select this to cancel dubbing operation.
7 Press w e to select “EXECUTE”, then press ENTER for
confirmation. The dubbing screen appears for 5 seconds.
NOTES:
● It is not possible to dub play lists on DVD discs.
● It is not possible to dub pre-recorded DVD VIDEO discs.
● It is not possible to dub Video CDs/SVCDs or Audio CDs.
Downloaded From DvDPlayer-Manual.com JVC Manuals
cassette with the record safety tab intact to the VHS deck.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “DVD ]VHS”, then press ENTER.
4 Press rtw e to select indexes (small pictures) of desired
original recordings and/or play lists, then press MARK. After
selecting all indexes you want to dub, press ENTER.
● You can select up to 8 original recordings and/or play lists.
5 Press rt to select “SELECT RECORDING MODE”, then press
ENTER. Press rt to select the desired option (SP or EP), then
press ENTER. The confirmation screen appears.
6 Press rt to “SELECT SOUND MODE”, then press ENTER.
Press rt to select the desired option (L/R, L, R or NORM), then
press ENTER. The confirmation screen appears.
7 Press t to select “CONFIRM”, then press ENTER.
8 Press VHS so that the VHS lamp lights up on the unit.
The current display on the screen will be switched to a receiving
broadcast display.
9 While holding 7, press 9 so that the VHS deck enters the
record pause mode.
10
Press DVD so that the DVD lamp lights up on the unit.
The dubbing screen will appear.
11 Press w e to select “EXECUTE”, then press ENTER to
confirm.
● To cancel the dubbing, press 8 then w e to select “CANCEL” and
press ENTER to confirm.
NOTES:
● It is not possible to dub play lists on DVD discs.
● It is not possible to dub Video CDs/SVCDs or Audio CDs.
● When dubbing is in progress, only 8 is functional.
72 EN EDITING
Dubbing From VHS To HDD
(Dubbing An Entire Cassette)
It is possible to perform automatic dubbing of all the recorded
programs of a cassette from the VHS deck to the HDD deck using
the “ENTIRE” dubbing.
1 Load the cassette you want to dub.
● Set “PICTURE CONTROL” to “EDIT” (墌 pg. 84).
● Set “VIDEO STABILIZER” to “OFF” (墌 pg. 85). However, if this is
set to “ON” during dubbing, it will be set to “OFF” automatically to
prevent image distortion. It will return to “ON” after dubbing is
completed.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “VHS ]HDD”, then press ENTER.
4 Press w e to select “ENTIRE”, then press ENTER.
5 Press rt to select “SELECT RECORDING MODE”, then press
ENTER. Press rt to select the desired option (SP or EP), then
press ENTER. The confirmation screen appears.
6 Press rt to “SELECT SOUND MODE”, then press ENTER.
Press rt to select the desired option (L/R, L, R or NORM), then
press ENTER. The confirmation screen appears.
7 Press t to select “CONFIRM”, then press ENTER.
8 Press w e to select “EXECUTE”, then press ENTER for
confirmation.
● To cancel the dubbing, press 8 then w e to select “CANCEL” and
press ENTER to confirm.
● If the tape is not rewind, the unit will start dubbing after automatically
rewinding the tape to the beginning.
● Upon completing dubbing, the tape will automatically be rewind.
NOTES:
● “SUPERIMPOSE” is automatically set to “OFF”. It will return to
“AUTO” after dubbing is completed.
● The program information at the VHS deck will not be dubbed.
● When there are blanks on the tape of more than 2 seconds, the HDD
deck will enter into pause mode. Dubbing will resume once recorded
portion is detected.
● Dubbing copyright guarded tape is not possible.
● When you select “EDIT” to dub tapes in step 1, be sure to select
“NORM” after you finish dubbing the tapes.
● When dubbing is in progress, only 8 is functional.
Dubbing From VHS To HDD
(Dubbing A Program From Cassette)
It is possible to dub a single title (program) of a cassette from the
VHS deck to the HDD deck using the “1 PROG.” dubbing.
1 Load the cassette you want to dub.
● Set “PICTURE CONTROL” to “EDIT” (墌 pg. 84).
● Set “VIDEO STABILIZER” to “OFF” (墌 pg. 85). However, if this is
set to “ON” during dubbing, it will be set to “OFF” automatically to
prevent image distortion. It will return to “ON” after dubbing is
completed.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “VHS ]HDD”, then press ENTER.
4 Press w e to select “1 PROG.”, then press ENTER.
5 After pressing r and ENTER, press rt to select the recording
mode, then press ENTER.
6 Press VHS so that the VHS lamp lights up on the unit.
The current display on the screen will be switched to a receiving
broadcast display.
7 Press AUDIO to select the playback sound.
8 Press 4 to locate the point from where you want to start
dubbing, then press 9.
VHS deck enters the record pause mode.
9 Press HDD so that the HDD lamp lights up on the unit.
The current display on the screen will be switched to a receiving
broadcast display.
Downloaded From DvDPlayer-Manual.com JVC Manuals
10 Press w e to select “EXECUTE”, then press ENTER for
confirmation.
● To cancel the dubbing, press 8 then w e to select “CANCEL” and
press ENTER to confirm.
NOTES:
● “SUPERIMPOSE” is automatically set to “OFF”. It will return to
“AUTO” after dubbing is completed.
● The program information at the VHS deck will not be dubbed.
● When there are blanks on the tape of more than 2 seconds, the HDD
deck will enter into pause mode. Dubbing will resume once recorded
portion is detected.
● Dubbing copyright guarded tape is not possible.
● When you select “EDIT” to dub tapes in step 1, be sure to select
“NORM” after you finish dubbing the tapes.
● When dubbing is in progress, only 8 is functional.
Dubbing From VHS To DVD
(Dubbing An Entire Cassette)
It is possible to perform automatic dubbing of all the recorded
programs of a cassette from the VHS deck to the DVD deck using
the “ENTIRE” dubbing.
1 Load the cassette you want to dub.
● Set “PICTURE CONTROL” to “EDIT” (墌 pg. 84).
● Set “VIDEO STABILIZER” to “OFF” (墌 pg. 85). However, if this is
set to “ON” during dubbing, it will be set to “OFF” automatically to
prevent image distortion. It will return to “ON” after dubbing is
completed.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “VHS ]DVD”, then press ENTER.
4 Press w e to select “ENTIRE”, then press ENTER.
5 Press rt to select “SELECT RECORDING MODE”, then press
ENTER. Press rt to select the desired option (SP or EP), then
press ENTER. The confirmation screen appears.
6 Press rt to “SELECT SOUND MODE”, then press ENTER.
Press rt to select the desired option (L/R, L, R or NORM), then
press ENTER. The confirmation screen appears.
7 Press t to select “CONFIRM”, then press ENTER.
8 Press w e to select “EXECUTE”, then press ENTER for
confirmation.
● To cancel the dubbing, press 8 then w e to select “CANCEL” and
press ENTER to confirm.
● If the tape is not rewind, the unit will start dubbing after automatically
rewinding the tape to the beginning.
● Upon completing dubbing, the tape will automatically be rewind.
NOTES:
● “SUPERIMPOSE” is automatically set to “OFF”. It will return to
“AUTO” after dubbing is completed.
● The program information at the VHS deck will not be dubbed.
● When there are blanks on the tape of more than 2 seconds, the DVD
deck will enter into pause mode. Dubbing will resume once recorded
portion is detected.
● Dubbing copyright guarded tape is not possible.
● When you select “EDIT” to dub tapes in step 1, be sure to select
“NORM” after you finish dubbing the tapes.
● When dubbing is in progress, only 8 is functional.
EDITING
Dubbing From VHS To DVD
(Dubbing A Program From Cassette)
It is possible to dub a single title (program) of a cassette from the
VHS deck to the DVD deck using the “1 PROG.” dubbing.
1 Load the cassette you want to dub.
● Set “PICTURE CONTROL” to “EDIT” (墌 pg. 84).
● Set “VIDEO STABILIZER” to “OFF” (墌 pg. 85). However, if this is
set to “ON” during dubbing, it will be set to “OFF” automatically to
prevent image distortion. It will return to “ON” after dubbing is
EN
73
About Disc Remaining Display
When dubbing from HDD to DVD, the unit displays the time
information for dubbing by bar meter. By comparing the disc
remaining time and the necessary time for dubbing of the selected
items, it is possible to check if the dubbing can be performed
completely or not.
When performing the High Speed Dubbing
Capacity of a disc
Remaining capacity
completed.
2 Press DUBBING to access the Dubbing Menu screen.
3 Press rtw e to select “VHS ]DVD”, then press ENTER.
4 Press w e to select “1 PROG.”, then press ENTER.
5 After pressing r and ENTER, press rt to select the recording
21%
Dark green: Length of already recorded item
Light green: Length of selected item
Yellow: Length of the item now being selected by arrow
Red: Excess over the capacity
mode, then press ENTER.
6 Press VHS so that the VHS lamp lights up on the unit.
The current display on the screen will be switched to a receiving
broadcast display.
7 Press AUDIO to select the playback sound.
8 Press 4 to locate the point from where you want to start
dubbing, then press 9.
VHS deck enters the record pause mode.
9 Press DVD so that the DVD lamp lights up on the unit.
The current display on the screen will be switched to a receiving
broadcast display.
10
When performing the Just Dubbing
TOTAL 105MIN
● The unit displays the status on the assumption that the selected
items are dubbed in the lowest transfer rate.
● The total time of a loaded disc is displayed on the right of the bar
meter.
When performing the Manual Dubbing
Press w e to select “EXECUTE”, then press ENTER for
confirmation.
● To cancel the dubbing, press 8 then w e to select “CANCEL” and
press ENTER to confirm.
NOTES:
● “SUPERIMPOSE” is automatically set to “OFF”. It will return to
“AUTO” after dubbing is completed.
● The program information at the VHS deck will not be dubbed.
● Dubbing copyright guarded tape is not possible.
● When you select “EDIT” to dub tapes in step 1, be sure to select
“NORM” after you finish dubbing the tapes.
● When dubbing is in progress, only 8 is functional.
Downloaded From DvDPlayer-Manual.com JVC Manuals
MAX
FR240
● The unit displays the status on the assumption that the selected
items are dubbed in the lowest transfer rate.
● The available highest transfer rate is displayed on the right of the bar
meter.
NOTE:
The bar meter moves up and down regularly, but this is not a
malfunction.
74
EN
EDITING
DV Dubbing (HDD & DVD Deck Only)
You can dub programs from a camcorder or DV equipment
connected to the unit with a DV cable. The unit’s remote control
allows you the limited control of the connected camcorder or DV
equipment functions during dubbing.
1 Connect a camcorder or DV equipment to the [DV IN] connector
on the unit’s front panel.
2 Press VHS/HDD/DVD SELECT on the unit repeatedly or HDD
on the remote so that the HDD lamp lights up on the unit.
3 Press CH +/– to set the channel to “DV”.
4 Press ON SCREEN.
● The on-screen display for DV dubbing appears.
NOTES:
● Use the DV cable VC-VDV 204U for connection.
● When you connect a PC to the DV IN connector, we do not assure
the normal operation of this unit.
Your unit
5 Press w e to select
, then press ENTER to display
the remote icon (facing to the right) for the DV equipment.
6 Press REC MODE repeatedly to set the recording mode.
7 Locate the point from where you want to start dubbing, then
stop or pause playback by pressing the following buttons on the
remote control: 4, 5, 3, 8, 9.
● To play back in slow speed (1/10 of the normal speed), press 9 to
pause playback, then press 3 or 5.
● To play back frame-by-frame, press 9 to pause playback, then press
9 repeatedly. Each press of 9 advances a frame.
● To change the playback direction, press 3 or 5.
8 Press w e to select
, then press ENTER repeatedly
until the desired sound track appears on the TV screen.
To [DV IN]
AUDIO 1: Select this to record the original stereo sound played
back on the connected DV equipment.
AUDIO 2: Select this to record the dubbed stereo sound played
back on the connected DV equipment.
MIX: Select this to record the sound of both “AUDIO 1” and
Camcorder
DV cable
(VC-VDV 204U)
(not supplied)
“AUDIO 2”.
● Note that this selection is not available when the source program is
recorded in 16BIT (48 kHz) mode.
9 Press w e to select
, then press ENTER. The
dubbing starts.
DV connector
DV equipment
● Playback on the external DV equipment and recording on the unit
should start simultaneously.
● To pause dubbing, press w e to select
, then press
ENTER. Both the unit and the external DV equipment pause
dubbing. Pressing 9 on the unit also works the same way.
10
The following on-screen display for DV dubbing appears when
ON SCREEN is pressed while the channel has been set to “DV”.
HDD
FR360
12bit
0:00
1:00
00:00:00. 00
DV
JVC
DV
A
2:00
GR-DV3500
00:00:00. 00
B
L – R
SOUND1
GR-DV3500
DV
DV
Press w e to select
press 8. The DV equipment stops.
, then press ENTER. Then
11
12
, then press ENTER.
Press w e to select
Press 8 twice on the remote control to stop dubbing.
● Both the unit and the external DV equipment stop dubbing.
NOTES:
● Dubbing copyright guarded programs is not possible.
● Original DV information such as the recording date and time are not
recorded.
● The superimposed indication during the operation or dubbing is not
recorded.
● If the dubbing is paused while the channel is set to “DV”, you cannot
switch channels.
1 2
C
A Remote control switch
To switch between the devices operable by the remote control
unit. The unit is operable when the remote icon (
)
displayed faces to the left, while the DV device is operable
when the remote icon is facing to the right.
B Auto capture button
Select to start or pause the dubbing. If ENTER is pressed when
the DV device is in the pause condition, preroll editing* where it
is possible to dub with a start time that is highly accurate will be
activated. When the DV device cannot be operated from the
unit (such as in camera mode), proceed with normal recording
(墌 pg. 41, 44).
* Preroll editing refers to the playback after the DV tape is slightly
rewind. (For DV devices that do not support the –1 speed, the
rewinding time may be longer.)
C Sound monitor switch
For selecting the desired sound format for recording. It is not
selectable during dubbing.
Downloaded From DvDPlayer-Manual.com JVC Manuals
When you dub from DV equipment other than a
camcorder
A Perform step 1 to 4.
B Locate the point from where you want to start dubbing, then
stop on the DV equipment.
● If you pause the DV equipment in this step, a few second’s still
picture will be recorded at the beginning of the recorded program.
C Set the input mode to “DV INPUT” on the DV equipment.
● If you select an input mode other than “DV INPUT”, unwanted
pictures may be recorded at the beginning of the recorded
program.
D Perform step 9 to 12.
To skip unwanted part of the source picture
Press ENTER to stop both equipment, then press w e to select
.
Locate the point where you want to restart dubbing by pressing 4,
5, or 3, then press 8.
Press w e to select
, then press ENTER to restart
dubbing.
EDITING
Edit From A Camcorder
EN
75
● Slide the TV/CABLE/DBS/DVD switch to DVD.
You can use a camcorder as the source player and your unit as the
recording deck.
A If the camcorder has no S-VIDEO output connector:
1 Make connections.
A If the camcorder has no S-VIDEO output connector:
— connect the camcorder’s AUDIO/VIDEO OUT connectors to the
unit’s [VIDEO/AUDIO ((MONO) L/R)] input connectors on the front
panel.
● When using a monaural camcorder, connect its AUDIO OUT
connector to the [AUDIO-L] input connector on your unit.
B If the camcorder has an S-VIDEO output connector:
— connect the camcorder’s AUDIO OUT and S-VIDEO OUT
connectors to the unit’s [AUDIO] and [S-VIDEO] input connectors
on the front panel.
To [VIDEO/AUDIO
((MONO) L/R)] input
Recorder
2 Press VHS/HDD/DVD SELECT on the unit repeatedly to select
the recording deck.
3 Press CH +/– to select “F-1”.
● Set “FRONT AUX F-1” to “VIDEO” for the VIDEO input connector, or
“S-VIDEO” for the S-VIDEO input connector, depending on the
connector being used. (墌 pg. 83)
Audio/video cable
(not supplied)
4 Press REC MODE repeatedly to set the recording mode.
5 Start playback on the camcorder slightly before the actual point
from where you wish to start dubbing.
6 Press 7 on the unit to start recording. Or while holding 7, press
4 on the remote control. The dubbing starts.
7 Press 8 on the unit, then stop playback on the camcorder.
NOTES:
● All necessary cables can be obtained from your dealer.
● Refer to the camcorder’s instruction manual for operating procedure.
● The quality of dubbed picture becomes poorer than that of the
original.
AUDIO/VIDEO OUT
Player
B If the camcorder has an S-VIDEO output connector (HDD
& DVD deck only):
To
[S-VIDEO]
input
To [AUDIO] input
S-video cable
(not supplied)
Recorder
Audio cable
(not supplied)
S-VIDEO OUT
AUDIO OUT
Player
Downloaded From DvDPlayer-Manual.com JVC Manuals
76
EN
EDITING
Edit To Or From Another Recorder
You can use your unit as the source player or as the recording
deck.
NOTE:
When using another recorder as the recording deck, refer to its
instruction manual.
A When recording on HDD or DVD deck
Your unit
Slide the TV/CABLE/DBS/DVD switch to DVD.
1 Make connections.
A When recording on HDD or DVD deck
1. If another recorder has no S-VIDEO connector, connect the unit’s
[AUDIO/VIDEO INPUT] connectors to the audio/video output
connectors on another recorder.
2. If another recorder has S-VIDEO connector, connect the
[AUDIO INPUT] and [S-VIDEO INPUT] connectors to the audio and
S-video output connectors on another recorder.
● If connecting a unit with an S-VIDEO connector, it is recommended to
use an optional S-Video cable to minimize picture degradation while
editing.
B When recording on VHS deck
1. Connect the unit’s [AUDIO/VIDEO INPUT] connectors to the audio/
video output connectors on another recorder.
Recorder
2 Press VHS/HDD/DVD SELECT on the unit repeatedly to select
the recording deck.
TV receiver
3 Press CH +/– to select “L-1” when using this unit as the
recording deck.
For HDD/DVD deck
● Set “REAR AUX L-1” to “VIDEO” for the VIDEO input connector, or
“S-VIDEO” for the S-VIDEO input connector, depending on the
connector being used. (墌 pg. 83)
4 Press REC MODE repeatedly to set the recording mode.
5 Engage the Play mode of the source player.
6 Engage the Record mode of the recording deck.
7 Stop recording on the recording deck, then stop playback on the
Another recorder
source player.
NOTES:
Player
● All necessary cables can be obtained from your dealer.
● When you use this unit as the source player for editing, be sure to set
“SUPERIMPOSE” to “OFF” before starting. (墌 pg. 82)
B When recording on VHS deck
Your unit
.
Recorder
TV receiver
Another recorder
Player
Downloaded From DvDPlayer-Manual.com JVC Manuals
EDITING
EN
77
1 Connect the unit and a digital audio device using either an
Digital Audio Dubbing
optional optical cable or an optional coaxial cable.
You can dub selected audio from a DVD or Audio CD disc to a
digital audio device.
However, it is not possible to dub copy-protected discs.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
Example: Dubbing to an MD
Recorder
2 Place a disc on the unit and load an MD on the connected digital
audio device.
3 Select the audio to be dubbed.
4 Start playback slightly before the actual point from where you
wish to start dubbing.
5 Press 9 to pause playback.
6 Select the input mode on the connected digital audio device.
7 Press 4 to start playback on the unit.
8 Start recording on the digital audio device.
9 Stop recording on the digital audio device. Then press 8 to stop
playback on the unit.
NOTE:
There may be a discrepancy of several seconds between where you
intend editing to start, and where it actually starts.
Digital audio device
(MD deck, etc.)
Optical cable
(not supplied)
To [DIGITAL AUDIO
OUT (OPTICAL)]
Player
Coaxial cable
(not supplied)
To [DIGITAL
AUDIO OUT
(COAXIAL)]
.
Rear of unit
Note for connection:
Remove the protection cap from the optical cable.
Downloaded From DvDPlayer-Manual.com JVC Manuals
78
EN
REMOTE CONTROL
Remote Control Functions
CABLE/DBS
TV
TV /VIDEO
1
Remote Control 1/2/3/4 Code Switching
The remote control is capable of controlling four JVC video units
independently. Each of the units can respond to one of four codes
(1, 2, 3 or 4). The remote control is preset to send 3 code signals
because your unit is initially set to respond to 3 code signals. You
can easily modify your unit to respond to 1, 2 or 4 code signals.
DVD
TV VOLUME +/–
0–9
CH +/–
TV MUTING
● Slide the TV/CABLE/DBS/DVD switch to DVD.
ENTER
1
4
SET UP
CABLE/DBS
TV
DVD
1–4
TV Multi-Brand Remote Control
Your remote control can operate the basic functions of your TV set.
In addition to JVC TVs, other manufacturer’s TVs can also be
controlled.
ENTER
● Turn off the TV using its remote control.
● Slide the TV/CABLE/DBS/DVD switch to TV.
IMPORTANT:
Although the provided remote control unit is compatible with JVC
televisions, as well as many other models, it may not work with your
TV, or in some instances, may have limited function capability.
8
SET UP
● Keep pressing SET UP down during step 1.
1 Enter your TV’s brand code using the number keys, then press
ENTER.
2 Press 1 on the unit’s remote control to turn on the TV and try
operations (墌 step 3).
● Keep pressing SET UP down during step 1.
1 Press the number key “1” for 1, “2” for 2, “3” for 3 or “4” for 4
to change the remote control code, then press ENTER.
2 Press 1 on the unit to turn off the unit.
3 Press 4 on the unit for over 5 seconds while the unit is turned
off. The code currently set appears on the front display panel.
● Once you have set the remote control to operate the TV, you do not
have to repeat this step until you replace your remote control’s
batteries.
● Some brands of TVs have more than one code. If the TV does not
function with one code, try entering another.
3 Press the corresponding buttons to operate the TV: 1, TV/
VIDEO, CH +/–, TV VOLUME +/–, TV MUTING, number keys.
● For some brands of TVs, you must press ENTER after having
pressed the number keys.
4 Press 8 on the remote control to change the unit’s code. The
BRAND NAME
CODE
code currently set on the remote control blinks on the front display
panel for approximately 5 seconds, and is applied to the unit.
NOTE:
When “POWER SAVE” is set to “ON” (墌 pg. 83), it is not possible to
JVC
HITACHI
MAGNAVOX
MITSUBISHI
PANASONIC
RCA
SHARP
SONY
SAMSUNG
SANYO
SEARS
TOSHIBA
ZENITH
01, 03
10
02
03
04, 11
05
06
07
12
13
13
08
09
change the remote code.
Downloaded From DvDPlayer-Manual.com JVC Manuals
REMOTE CONTROL
Cable Box Or DBS Receiver Multi-Brand Remote
Control
Your remote control can operate the basic functions of your cable
box or DBS (Direct Broadcast Satellite) receiver set. In addition to
JVC cable boxes or DBS receivers, other manufacturer’s cable
boxes or DBS receivers can also be controlled.
● Slide the TV/CABLE/DBS/DVD switch to CABLE/DBS.
● Keep pressing SET UP down during step 1.
1 Enter your cable box or DBS receiver’s brand code using the
number keys, then press ENTER.
2 Press 1 on the unit’s remote control to turn on the cable box or
DBS receiver and try operations (墌 step 3).
● Once you have set the remote control to operate the cable box or
DBS receiver, you do not have to repeat this step until you replace
your remote control’s batteries.
● Some brands of cable box or DBS receiver have more than one
code. If the cable box or DBS receiver does not function with one
code, try entering another.
3 Press the corresponding buttons to operate the cable box or
DBS receiver: 1, CH +/–, number keys.
● For some brands of cable box, you must press ENTER after having
pressed the number keys.
● The number keys may not function with some cable boxes.
IMPORTANT:
It may not work with your cable box, or in some instances, may have
limited function capability.
NOTES:
● You must set the brand for your remote control and for your
Controller (墌 pg. 24) separately. The list of brands that can be
controlled by your remote control is different from the list of brands
that can be controlled by your controller.
● It’s not possible to operate a cable box or DBS receiver that is not
equipped with a receiving window.
● It’s not possible to set the remote control for both your cable box and
a DBS receiver at the same time. You can only set the remote control
to operate one of these units at a time.
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
CABLE BOX BRAND
CODE
ARCHER
CABLETENNA
CABLEVIEW
CITIZEN
CURTIS
DIAMOND
GC BRAND
GEMINI
GENERAL INSTRUMENTS
HAMLIN
JASCO
JERROLD
NOVAVISION
OAK
PANASONIC
PULSER
RCA
REGAL
REMBRANDT
SAMSUNG
SCIENTIFIC ATLANTA
SIGMA
SL MARX
SPRUCER
STARGATE
TELEVIEW
TOCOM
UNIKA
UNIVERSAL
VIDEOWAY
ZENITH
01, 05, 17
01, 17
15, 16, 17, 21, 25
15, 16, 17, 21, 25
02
01, 17
15, 16, 17, 21, 25
15
01, 04, 06, 11, 12, 15, 28
10, 18, 23
15
01, 04, 06, 11, 12, 15, 28
02
07
13, 14
15, 16, 17, 21, 25
13, 14
10, 18, 23
01, 16, 17
05, 16, 24
02
07
05, 16, 17, 24, 25
13, 14
05, 15, 16, 17, 21, 24, 25
05, 16, 24
01, 04, 16
01, 17
16, 17, 25
03, 09, 22
03, 09, 22
DBS RECEIVER BRAND
CODE
JVC (DISH Network)
ECHOSTAR (DISH Network)
SONY (DSS)
RCA (DSS)
51
51
41
40
79
80
EN
SYSTEM CONNECTIONS
Connecting To A Dolby Digital Decoder
Or An Amplifier With Built-in DTS
These instructions enable you to connect your unit to a Dolby
Digital Decoder or an amplifier with built-in DTS.
1 Connect the unit and a Dolby Digital Decoder or an amplifier
with built-in DTS using either an optional optical cable or an
optional coaxial cable.
NOTES:
● For Dolby Digital sound, set “DIGITAL AUDIO OUT” to “DOLBY
DIGITAL/PCM”. (墌 pg. 81)
● For DTS sound, set “DIGITAL AUDIO OUT” to “STREAM/PCM”.
(墌 pg. 81)
CAUTIONS:
● This unit has a dynamic range of more than 110 dB with regards to its
Hi-Fi audio capability. It is recommended that you check the
maximum level if you are going to listen to the Hi-Fi audio signals
through a stereo amplifier. A sudden surge in the input level to the
speakers may damage them.
● Some speakers and televisions are specially shielded to prevent
television interference. If both are of the non-shielded type, do not
place the speakers adjacent to the TV set as this can adversely affect
the playback picture.
Dolby Digital Decoder or
amplifier with built-in DTS
To DIGITAL AUDIO input
Optical cable
(not supplied)
To [DIGITAL AUDIO
OUT (OPTICAL)]
Coaxial cable
(not supplied)
To [DIGITAL
AUDIO OUT
(COAXIAL)]
.
Rear of unit
Note for connection:
Remove the protection cap from the optical cable.
Downloaded From DvDPlayer-Manual.com JVC Manuals
SUBSIDIARY SETTINGS
Mode Set
(HDD & DVD Deck Only)
81
AUDIO OUTPUT
8 DIGITAL AUDIO OUT — DOLBY DIGITAL/PCM / STREAM/
PCM / PCM ONLY
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
Set to the appropriate mode according to the type of the device
connected to [DIGITAL AUDIO OUTPUT] connector.
DOLBY DIGITAL/PCM: Select this when you connect the digital
input connector of a Dolby Digital Decoder or an amplifier with a
built-in Dolby Digital Decoder.
STREAM/PCM: Select this when you connect the digital input
connector of an amplifier with a built-in DTS, Dolby Digital, or
MPEG multichannel decoder.
PCM ONLY: Select this when you connect the linear PCM digital
input of other audio equipment (amplifier, MD or DAT deck, etc.).
NOTES:
CABLE/DBS
TV
HDD
EN
* The boldface settings below indicate the settings at your purchase.
DVD
DVD
● This setting also functions when HDD is active.
● If you watch or play back a title which contains multiple audio
languages, select “PCM ONLY” in advance and choose main or sub
audio with AUDIO.
ENTER
rtwe
8 ANALOG AUDIO OUT — STEREO / DOLBY SURROUND
Select the appropriate setting to accommodate the unit to the
connected A/V equipment. This function takes effect when a
DVD VIDEO disc is played back.
STEREO: Select this when listening to conventional two-channel
stereo audio with the unit’s [AUDIO OUTPUT] connectors
connected to a stereo amplifier/receiver or TV set, or in case you
want to record the audio from a DVD VIDEO disc to a Mini Disc,
etc.
DOLBY SURROUND: Select this when listening to multichannel
surround audio with the unit’s [AUDIO OUTPUT] connectors
connected to an amplifier/receiver with a built-in surround
decoder or a surround decoder.
SET UP
AUDIO
Various modes of this unit are categorized into menus nested in 2
levels shown in the following table. To change the settings of these
modes, find the desired mode in the menu (for details on each
menu, see pages 81 through 82), then follow the procedure below.
DVD VIDEO SET UP
LANGUAGE SET (墌 pg. 21)
AUDIO OUTPUT (墌 pg. 81)
PARENTAL LOCK (墌 pg. 40)
DISC PLAY SET UP (墌 pg. 82)
HDD/DVD SET UP
HDD SET UP (墌 pg. 82)
DVD SET UP (墌 pg. 82)
DISC SET UP (墌 pg. 87, 88)
FUNCTION SET UP
REC/PLAY SET UP (墌 pg. 82)
DISPLAY SET (墌 pg. 82)
VIDEO IN/OUT (墌 pg. 26, 83)
INITIAL SET UP
TUNER SET (墌 pg. 23)
STB SET (墌 pg. 24)
CLOCK SET (墌 pg. 22)
● The procedure below shows how to set the desired option of the
“2ND AUDIO REC” mode as an example.
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “FUNCTION SET UP”, then press t.
4 Press w e to select “REC/PLAY
DVD VIDEO SET UP
SET UP”, then press t.
5 Press rt to select “2ND
AUDIO REC”, then press ENTER.
6 Press rt to select the desired
option, then press ENTER.
7 Press SET UP to complete the
HDD/DVD SET UP
FUNCTION SET UP
DISPLAY SET
VIDEO IN/OUT
REC/PLAY SET UP
XP MODE REC AUDIO
2ND AUDIO REC
JUMP TIME
SET UP
ENTER
EXIT
SELECT
INITIAL SET UP
DOLBY DIGITAL
OFF
15MIN
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
setting.
Downloaded From DvDPlayer-Manual.com JVC Manuals
8 D. RANGE CONTROL — NORMAL / WIDE RANGE / TV
MODE
The dynamic range (the difference between the loudest sound and
the quietest one) can be compressed during playback of a program
encoded in Dolby Digital format.
This function takes effect when a DVD VIDEO disc recorded in
Dolby Digital format is played back at low or middle volume.
NORMAL: Normally select this setting to activate this function.
WIDE RANGE: Select this to deactivate this function when you
enjoy wide dynamic range program.
TV MODE: Select this when you hear the sound through the TV’s
speaker(s).
NOTES:
● This function has no effect on programs other than that recorded in
Dolby Digital format.
● This function does not work when Simulated Surround Effect is
activated. (墌 pg. 38)
● The effect of “NORMAL” and “WIDE RANGE” may not be different
depending on discs.
8 OUTPUT LEVEL — STANDARD / LOW
You can lower the output level of analog audio to accommodate
the unit to the connected A/V equipment.
STANDARD: Normally select this setting.
LOW: The output level of analog audio is lowered.
82 EN SUBSIDIARY SETTINGS
DISC PLAY SET UP
REC/PLAY SET UP
8 RESUME — OFF / ON / DISC RESUME
8 XP MODE REC AUDIO — DOLBY DIGITAL / LINEAR PCM
When this function is set to “ON” or “DISC RESUME”, you can use
the resume function. (墌 pg. 29)
OFF: You cannot use the resume function.
ON: You can start playback from the resume point of the placed
disc.
DISC RESUME: The unit retains a memory of the resume points of
the last 30 discs played back, even though they have been
ejected.
NOTE:
You can select the audio format when you record a title in XP
mode. When this function is set to “LINEAR PCM”, you can obtain
a high-quality audio sound.
DOLBY DIGITAL: To record in Dolby Digital format.
LINEAR PCM: To record in Linear PCM format.
“DISC RESUME” setting works on DVD VIDEO, VCD, SVCD and
already finalized DVD-R/DVD-RW (video mode) discs. For other types
of discs, the function under “ON” setting will be applied even if
“RESUME” is set to “DISC RESUME”.
HDD SET UP
8 LIVE MEMORY — OFF / 30 MIN / 1 HR / 3 HR
When this function is set to “30 MIN”, “1 HR” or “3 HR”, you can
apply the selected time length to “Temporary recording for Live
Memory” (墌 pg. 47).
DVD SET UP
8 SAVE AS LIBRARY — OFF / ON
When this function is set to “ON”, the recording information is
automatically stored in the library. For details, refer to “Modify
Library Information” (墌 pg. 68).
8 CONTINUOUS PLAY — OFF / ON
When this function is set to “ON”, multiple titles on a disc are
played back continuously one after another.
8 2ND AUDIO RECORD — OFF / ON
When this function is set to “ON”;
If a SAP program is received, the SAP audio is recorded on L/R
tracks. The main audio is not recorded.
If a non-SAP program is received, the main audio is recorded on L/
R tracks.
When this function is set to “OFF”, the SAP audio cannot be
recorded.
NOTE:
When the channel is changed on the unit;
● The “MONO” indicator appears on the screen for about 5 seconds if
the program is a monaural broadcast.
● The “STEREO” indicator appears on the screen for about 5 seconds
if the program is a stereo broadcast.
● Both “STEREO” and “SAP” indicators appear when a stereo program
is accompanied by SAP sound.
● Both “MONO” and “SAP” indicators appear when the main audio on
the monaural broadcast is accompanied by SAP sound.
8 JUMP TIME — 15 MIN / 30 MIN / 1 HR
You can locate a scene ahead of or behind the currently viewed
one by jumping a selected time interval during playback (or Live
Memory Playback) or recording (or Live Memory Recording). For
details, refer to “Jump Search” (墌 pg. 49)
DISPLAY SET
8 VIDEO MODE RECORDING ASPECT — PRIORITIZE 4:3 /
PRIORITIZE 16:9
8 SUPERIMPOSE — OFF / AUTO
This is the setting for the aspect ratio used when you dub titles to
DVD discs in video mode. If the titles you want to dub are recorded
in both 16:9 and 4:3, you must select one aspect ratio.
PRIORITIZE 4:3: If you select “PRIORITIZE 4:3”, even a title
recorded in 16:9 is dubbed in 4:3.
PRIORITIZE 16:9: If you select “PRIORITIZE 16:9”, even a title
recorded in 4:3 is dubbed in 16:9.
NOTES:
8 VIDEO MODE RECORDING AUDIO — MAIN / SUB
This is the setting for the audio channel to be selected when
dubbing titles to DVD discs in video mode. Select either one of the
two settings if the titles to be dubbed have two audio channels.
MAIN: Select this to dub the main channel.
SUB: Select this to dub the sub channel.
8 MP3 & WMA / JPEG — MP3 & WMA / JPEG
You can select files to play back, when both MP3&WMA files and
JPEG files are recorded on a disc.
MP3 & WMA: Select this to play back MP3/WMA files.
JPEG: Select this to play back JPEG files.
When this function is set to “AUTO”, various operational indicators
appear on the TV screen. Messages appear in the selected
language. (墌 pg. 21)
OFF: To turn off superimposed indications.
AUTO: To superimpose operational indications for approximately
five seconds just after the corresponding operation.
● Even when “SUPERIMPOSE” is set to “OFF”, you can display the
various operational indicators by pressing ON SCREEN. To clear the
operational indicators, press ON SCREEN again.
● When you use this unit as the source player for editing, be sure to set
“SUPERIMPOSE” to “OFF” before starting. (墌 pg. 76)
● When you select “AUTO”, during playback, the operation mode
indicators may be disturbed depending on the type of disc being
used.
8 BLUE BACK — OFF / ON
When this function is set to “ON”, the TV screen becomes all blue
when receiving a channel not in use.
NOTE:
When you want to receive an unstable channel with poor signals, set
this function to “OFF”.
Downloaded From DvDPlayer-Manual.com JVC Manuals
SUBSIDIARY SETTINGS
8 POWER SAVE — OFF / ON
When this function is set to “ON”, you can reduce the power
consumption while the unit is turned off.
● During Power Save mode —
— the front display panel will be turned off.
● Power Save does not work when —
— the unit is in the Timer mode.
— the unit’s power is turned off after timer-recording or Instant Timer
Recording.
— the Automatic Satellite Program Recording mode is engaged.
(墌 pg. 59)
● It takes some time for the unit to complete initialization after you turn
on the unit power, with “WAKE UP” blinking on the front display
panel.
8 ON SCREEN LANGUAGE
This unit offers you the choice to view on-screen messages in 3
different languages.
For details, refer to “On-screen Language Set” (墌 pg. 21).
83
Scan Mode Set
8 DIMMER — BRIGHT / DIMMED
You can change the brightness of the front display panel.
BRIGHT: Normally select this.
DIMMED: To dim the front display panel. (Blue lamp on the front
display panel is turned off.)
EN
If you connect the unit and TV with Component Video Connection
(墌 pg. 19), you can select the scan mode from two modes:
Interlaced scan mode which is used in the conventional TV
system, and Progressive scan mode which enables reproduction
of higher-quality images.
8 Interlaced scan
In the conventional video system, a picture is shown on the display
monitor in two halves. The Interlaced scan system places lines of the
second half of the picture in-between lines of the first half of the picture.
8 Progressive scan
Progressive scan displays all the horizontal lines of a picture at one time,
as a single frame. This system can convert the interlaced video from DVD
into progressive format for connection to a progressive display. It
dramatically increases the vertical resolution.
ATTENTION:
Your TV needs to be compatible with Progressive.
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
VIDEO IN/OUT
CABLE/DBS
TV
8 MONITOR TYPE — 4:3LB / 4:3PS / 16:9 AUTO / 16:9 FIX
HDD
You can select the monitor type depending on the TV used when
you play back DVD VIDEO discs recorded for wide-screen TVs.
For details, refer to “Monitor Set” (墌 pg. 26).
DVD
DVD
8 FRONT AUX F-1 — VIDEO / S-VIDEO
Select the appropriate mode depending on the connector (F-1)
being used on the front panel.
VIDEO: To use the [VIDEO] input connector on the front panel.
S-VIDEO: To use the [S-VIDEO] input connector on the front panel.
8 REAR AUX L-1 — VIDEO / S-VIDEO
Select the appropriate mode depending on the connector (L-1)
being used on the rear panel.
VIDEO: To use the [VIDEO INPUT] connector on the rear panel.
S-VIDEO: To use the [S-VIDEO INPUT] connector on the rear
panel.
.
PROGRESSIVE SCAN
1 Press HDD or DVD so that the HDD or DVD lamp lights up on the unit.
2 Press PROGRESSIVE SCAN for 3 or more seconds.
● Video output indicator ( ) lights on the front display panel if Progressive
scan mode has been established. (墌 pg. 14)
● Each press of PROGRESSIVE SCAN for 3 or more seconds switches the
scan mode.
NOTES:
●
●
●
●
Interlaced scan mode is the setting at your purchase.
Interlaced scan mode might be suitable depending on video material.
Scan mode cannot be set while menu screen is displayed.
When the Progressive scan mode is engaged, no video signal is
output from [S-VIDEO OUTPUT] connector and [VIDEO/AUDIO
OUTPUT] connectors.
Watch the images on VHS deck in the Progressive scan
mode via component video
1 Set the Progressive-compatible TV to the component input mode.
2 Press HDD or DVD so that the HDD or DVD lamp lights up on the
unit.
3 Press PROGRESSIVE SCAN for 3 or more seconds.
● The video output indicator
lights up on the front display panel.
4 Press VHS so that the VHS lamp lights up on the unit, then press
PROGRESSIVE SCAN.
● “COMP OFF” is displayed on the front display panel. It will be displayed for
5 seconds.
5 Press PROGRESSIVE SCAN again within 5 seconds.
● “COMP ON” is displayed on the front display panel.
● The VHS progressive scan image will then be outputted from the
[COMPONENT VIDEO OUT (Y/PB/PR)] connectors.
NOTES:
● Be sure to engage the HDD or DVD deck in stop mode.
● To disengage the VHS Progressive Scan mode, perform steps 4
and 5 to switch to “COMP OFF”.
Downloaded From DvDPlayer-Manual.com JVC Manuals
84
EN
SUBSIDIARY SETTINGS
* The boldface settings below indicate the settings at your purchase.
Mode Set
(VHS Deck Only)
FUNCTION
8 PICTURE CONTROL — NORM / EDIT / SOFT / SHARP
This feature helps you to adjust the playback picture quality
according to your preference. Normally select “NORM”.
NORM: Picture quality is adjusted automatically.
EDIT: Minimizes picture degradation during editing (recording and
playback).
SOFT: Reduces image coarseness when viewing overplayed tapes
containing a lot of noise.
SHARP: Clearer, sharper-edged picture when viewing images with
lots of flat, same-colored surfaces such as cartoons.
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
CABLE/DBS
TV
DVD
VHS
NOTES:
● When you select “EDIT”, “SOFT” or “SHARP”, the selected mode will
not change until you select another mode.
● When you select “EDIT” to dub tapes, be sure to select “NORM” after
you finish dubbing the tapes.
ENTER
8 SUPERIMPOSE — AUTO / OFF
rtwe
When this function is set to “AUTO”, various operational indicators
appear on the TV screen. Messages appear in the selected
language. (墌 pg. 21)
NOTES:
● Even when “SUPERIMPOSE” is set to “OFF”, you can display the
various operational indicators by pressing ON SCREEN. To clear the
operational indicators, press ON SCREEN again.
● When you use this unit as the source player for editing, be sure to set
“SUPERIMPOSE” to “OFF” before starting.
● During playback, the operation mode indicators may be disturbed
depending on the type of tape being used.
SET UP
8 AUTO SP]EP TIMER — ON / OFF
You can change various mode settings on the Function Set
screen.
To change the settings of these modes, find the desired mode in
the menu (for details on each menu, see pages 84 through 85),
then follow the procedure below.
1 Press VHS so that the VHS lamp lights up on the unit.
2 Press SET UP to access the
FUNCTION
Function Set screen.
3 Press rt to select the item you
want to change, then press ENTER
or e to select the desired mode.
4 Press SET UP to complete the
setting.
PICTURE CONTROL
SUPERIMPOSE
AUTO SP EP TIMER
VIDEO STABILIZER
BLUE BACK
2ND AUDIO RECORD
( , ) THEN (ENTER)
(SET UP) TO END
NORM
AUTO
OFF
OFF
ON
OFF
When this function is set to “ON”, the unit automatically switches to
EP mode to allow complete recording if there is not enough tape to
record the entire program while timer-recording in SP mode.
For Example:
Recording a program of 140 minutes in length onto a 120-minute
tape.
Approximately 110 minutes
SP mode
Approximately 30 minutes
EP mode
Total 140 minutes
Make sure you set this function to “ON”, before the timer-recording
starts.
NOTES:
● If you have programmed the unit to timer-record 2 or more programs,
the second program and those thereafter may not fit on the tape if
you set “AUTO SP]EP TIMER” to “ON”. In this case, make sure the
mode is not engaged, then set the tape speed manually during timer
programming.
● In order to ensure that the recording fits on the tape, this feature may
leave a slight non-recorded section at the end of the tape.
● There may be some noise and sound disturbance at the point on the
tape where the unit switches from SP to EP mode.
● The Auto SP]EP Timer feature is not available during ITR (Instant
Timer Recording), and the feature will not work properly on the
following tapes: T(ST)-30, T(ST)-60, T(ST)-90, and T(ST)-120.
Downloaded From DvDPlayer-Manual.com JVC Manuals
SUBSIDIARY SETTINGS
8 VIDEO STABILIZER — ON / OFF
When this function is set to “ON”, you can automatically correct
vertical vibration in the picture when playing back unstable
recordings made on another recorder.
NOTES:
● When you finish viewing a tape, be sure to set this function to “OFF”.
● Regardless of the setting, this function has no effect during recording
and during special effects playback.
● The on-screen display may jitter vertically when this function is set to
“ON”.
● To watch recordings with close-caption, set this function to “OFF”.
EN
85
Tray Lock (DVD Deck Only)
You can lock the disc tray to prohibit the unwanted disc ejection by
children.
● Turn off the unit.
x
8
8 BLUE BACK — ON / OFF
When this function is set to “ON”, the TV screen becomes all blue
when receiving a channel not in use.
NOTE:
When you want to receive an unstable channel with poor signals, set
this function to “OFF”.
8 2ND AUDIO RECORD — ON / OFF
When this function is set to “ON”;
If a SAP program is received, the SAP audio is recorded on L/R
tracks. The main audio is not recorded.
If a non-SAP program is received, the main audio is recorded on L/
R tracks.
When this function is set to “OFF”, the SAP audio cannot be
recorded.
NOTE:
When the channel is changed on the unit;
● The “STEREO” indicator appears on the screen for about 5 seconds
if the program is a stereo broadcast.
● Both “STEREO” and “SAP” indicators appear when a stereo program
is accompanied by SAP sound.
Downloaded From DvDPlayer-Manual.com JVC Manuals
To lock tray
While the unit is turned off, press and hold 8, then press x on the
unit. “LOCK” appears on the front display panel and the disc tray is
locked.
To unlock tray
While the unit is turned off, press and hold 8, then press x on the
unit. “UNLOCK” appears on the front display panel.
86
EN
SUBSIDIARY SETTINGS
Guide Channel Number Set
Changing VCR Plus+ Setting
®
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
The VCR Plus+ programming system assigns a VCR Plus+ guide
channel to the TV channels and the cable channels. These guide
channel numbers are also called the VCR Plus+ channel codes.
Most TV listings have a section, usually a chart, indicating the
guide channel numbers assigned to each station.
To ensure that VCR Plus+ timer recording operates correctly, it is
necessary to set the “VCR Plus+ Guide Channel” for each station.
If you have moved to a different area or if a broadcasting station’s
channel number has been changed, perform the following steps to
set the correct guide channel number.
the unit.
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “INITIAL SET UP”, then press t.
4 Press w e to select “TUNER
SET”, then press t.
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
CABLE/DBS
TV
DVD
TUNER SET
FUNCTION SET UP
STB SET
5 Press rt w e to select “GUIDE
INITIAL SET UP
CLOCK SET
AUTO CH SET
MANUAL CH SET
CH SET”, then press ENTER.
GUIDE CH SET
11
NOTES:
● In many instances, the VCR Plus+ guide channel numbers for cable
and broadcast TV stations DO NOT match the channel number on
which it is received by your unit or cable box. Check your TV listing,
or contact your cable supplier for details.
● Many TV stations can be viewed on cable. Check your TV listing, or
contact your cable supplier for details.
DVD VIDEO SET UP HDD/DVD SET UP
6 Press rt to select “GUIDE
CH”, then press ENTER.
7 Press rt to select the Guide
SET UP
ENTER
EXIT
SELECT
11
12
13
12
13
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
INITIAL SET UP > GUIDE CH SET
GUIDE CH
1
CABLE CH
--
Channel number for the desired
station as shown in the TV listings.
Then press ENTER.
RETURN
● If you receive your channels with a
ENTER SELECT WITH [
SET UP
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
EXIT
SELECT
cable box and if you have properly
set your Controller, “CABLE CH”
appears in place of “DVD CH”. If not, perform “Cable Box and/or DBS
Receiver Control Setting (HDD & DVD Deck only)” (墌 pg. 24).
8 Press rt to select “DVD CH”, then press ENTER. Press rt
to select the number of the unit’s channel position on which the
Guide Channel Number’s broadcast is received by the unit or the
DBS receiver. Then press ENTER.
● To timer-record a satellite program with the VCR Plus+ system, you
need to install the provided Satellite Controller and perform the
procedure described in “Cable Box and/or DBS Receiver Control
Setting (HDD & DVD Deck only)” (墌 pg. 24).
● Repeat steps 6 – 8 as necessary.
9 Press SET UP to complete the setting.
ENTER
rtwe
Guide Channel Number
“Guide Channel (GUIDE CH) Number” refers to the assigned TV
station numbers, according to broadcast area, for the VCR Plus+
timer recording. The Guide Channel Numbers can be found in
most TV listings.
SET UP
Downloaded From DvDPlayer-Manual.com JVC Manuals
SUBSIDIARY SETTINGS
Format A Disc (DVD Deck Only)
EN
87
Format A DVD-RAM Disc
1 Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
Some DVD-RAM/RW discs are unformatted.
Format the disc when you use an unformatted disc or you want to
delete all recordings and data on the disc.
ATTENTION:
● When a disc is formatted, all recordings and data are erased. It is
impossible to restore them.
● Never turn off the unit or disconnect the AC power cord while
“NOW FORMATTING...” is displayed on the TV screen.
●
●
●
●
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
Load a DVD-RAM/RW disc to format.
CABLE/DBS
TV
DVD
2 Press SET UP to access the Main Menu screen.
3 Press w e to select “HDD/DVD SET UP”, then press t.
4 Press w e to select “DISC SET
UP”, then press t.
DVD VIDEO SET UP HDD/DVD SET UP
HDD SET UP
5 Press rt w e to select
DISC SET UP
FINALIZE
CANC. FINALIZ.
press ENTER.
INITIAL SET UP
Video
“FORMAT”, then press ENTER.
Press w e to select “OK”, then
press ENTER.
6 Press w e to select “OK”, then
FUNCTION SET UP
DVD SET UP
Vid
eo
FORMAT
SET UP
ENTER
EXIT
SELECT
SELECT WITH [
] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
Format A DVD-RW Disc
1 Perform steps 1 to 4 of “Format A DVD-RAM Disc” as above
before continuing.
2 Press rt w e to select “FORMAT”, then press ENTER. Press
w e to choose “VR MODE” or “VIDEO MODE”, then press ENTER
when “DISC WILL BE FORMATTED” appears on the TV screen.
“VR MODE”: To be chosen when you want to record, erase, or edit
data on the disc repeatedly.
“VIDEO MODE”: To be chosen when you want to erase all the data
on the disc once played back to record new data, or play back the
disc on other DVD players.
3 Press w e to select “OK”, then press ENTER.
NOTES:
ENTER
rtwe
SET UP
Downloaded From DvDPlayer-Manual.com JVC Manuals
● It is impossible to format Version 1.0 DVD-RW discs in Video mode.
● It is impossible to format DVD-R discs.
● All the titles on a disc will be deleted once the disc is formatted even
if they are protected titles. (墌 pg. 65)
88
EN
SUBSIDIARY SETTINGS
Finalize A Disc (DVD Deck Only)
Finalize A DVD-R/RW Disc
1 Perform steps 1 to 4 of “Format A DVD-RAM Disc” (墌 pg. 87)
before continuing.
2 Press rt w e to select “FINALIZE”, then press ENTER.
Finalizing DVD-R/RW discs recorded on this unit makes it possible
for the discs to be played back on other DVD players. DVD-RW
discs are finalized in the mode that the discs were formatted,
enabling playback on compatible DVD players.
Title names input in the Library Database Navigation are
registered as title names in the DVD menu. (墌 pg. 64)
●
●
●
●
Turn on the unit.
Turn on the TV and select the video channel (or AV mode).
Slide the TV/CABLE/DBS/DVD switch to DVD.
Load a DVD-R/RW disc to finalize.
CABLE/DBS
TV
DVD
● For DVD-R/RW (Video mode) discs, the background selection screen
will appear. Press rt w e to select the desired background from a
selection of 18 backgrounds.
3 Press w e to select “OK”, then press ENTER.
4 Press w e to select “OK”, then press ENTER.
5 Press SET UP to return to the normal screen.
● Menu screen is cleared.
● Once a DVD-R/RW (Video mode) disc has been finalized, the
displays for original and play list do not appear. Only display for
library appears.
● Once a DVD-RW (VR mode) disc has been finalized, it can be played
on DVD players compatible with VR mode.
Cancel The Finalization Of A DVD-RW Disc
1 Load a DVD-RW disc to cancel the disc finalization, and perform
steps 1 to 4 of “Format A DVD-RAM Disc” (墌 pg. 87) before
continuing.
2 Press rt w e to select “CANC. FINALIZ.”, then press ENTER.
3 Press w e to select “EXECUTE”, then press ENTER.
4 Press SET UP to return to the normal screen.
● When the disc finalization is canceled, the mode in which the disc
was formatted is restored, making the disc recordable. (墌 pg. 9, 87)
ENTER
rtwe
SET UP
Before finalizing
●
●
●
●
●
It is possible to record on a blank space.
It is possible to enter title names. (墌 pg. 64)
It is possible to delete titles. (墌 pg. 65)
It is impossible to overwrite recorded areas of DVD-R discs.
Available recording capacity does not increase even if a recorded
title is deleted from a DVD-R disc.
● It is impossible to record or edit DVD-R/RW discs recorded on other
devices even if they have not been finalized.
After finalizing (For DVD-R/RW (Video mode) discs)
● Video and audio that have been recorded by then are recorded in
conformity to the DVD Video standard, enabling you to play back the
discs as DVD VIDEO discs.
● Although DVD-R/RW discs finalized on this unit become playable on
DVD players compatible with DVD-R/RW discs, some discs still may
not play, for which JVC cannot take responsibility.
● Marked points marked before finalizing will be deleted, and titles will
be divided automatically into “chapters” approximately every 5
minutes. (墌 pg. 29)
● Depending on the DVD players and DVD-R/RW discs used, and on
the conditions of recording, it may not be possible to play back the
discs. In this case, play back the discs on this unit.
● Additional recordings become impossible.
Downloaded From DvDPlayer-Manual.com JVC Manuals
TROUBLESHOOTING
Before requesting service for a problem, use this chart and see if
you can solve the trouble yourself. Small problems are often easily
solved, and this can save you the trouble of sending your unit off
for repair.
Initializing (DVD Deck Only)
Malfunction occurs on the unit.
]Press 1 to turn off the unit, press and hold 1, then press 8
for two seconds or more.
General
No power is supplied to the unit.
● The AC power plug is disconnected from the AC outlet.
]Connect the AC power plug to the AC outlet securely.
(墌 pg. 19)
The remote control does not work properly.
]Remove the batteries, wait for 5 minutes or more, then load the
butteries again.
● The setting of the remote control code is inappropriate.
]Set the same remote control code (1, 2, 3, or 4) on both the unit
and the remote control. (墌 pg. 78)
● The batteries are discharged.
]Replace the dead batteries with new ones.
Dubbing from the external equipment is not possible.
● The source (another video recorder, camcorder) has not been
properly connected.
]Confirm that the source is properly connected.
● All necessary power switches have not been turned on.
]Confirm that all units’ power switches are turned on.
● The setting of the input channel position is inappropriate.
]Select the input channel position (“F-1” or “L-1”) that
corresponds to the input terminal connected to the external
equipment. (墌 pg. 76)
The on-screen display superimposed on the program played
back/received on this unit is recorded when you dub the program
to an external recording equipment.
]Set “SUPERIMPOSE” to “OFF”. (墌 pg. 82)
EN
89
Playback (DVD Deck)
The DVD deck cannot be operated.
● The DVD deck is not selected.
]Press VHS/HDD/DVD SELECT on the unit repeatedly or DVD
on the remote so that the DVD lamp lights up on the unit.
Images do not appear on the TV screen.
● The TV receiver’s channel selector is not set to the video
channel or AV mode.
]If you are using the RF connection, set the TV receiver to the
video channel.
]If you are using the AV, S-VIDEO or Component Video
connection, set the TV to its AV mode.
● The unit’s video channel has not been correctly set.
]Perform the video channel set. (墌 pg. 19)
● When interlace scanned program is played back, progressive
scan mode is selected.
]Press and hold PROGRESSIVE SCAN until
disappears from
the front display panel. (墌 pg. 83)
Playback does not start or stop immediately after playback is
started by pressing .
On the front display panel, “NO DISC” appears.
● The disc is loaded upside down.
]Place the disc on the disc tray with the playback surface facing
down. (墌 pg. 10)
● A disc not being compatible with the unit is loaded.
]Load a playable disc on the unit. (墌 pg. 7)
● A dirty disc is loaded.
]Clean the disc. (墌 pg. 11)
● Defective disc is loaded.
]Replace the warped or scratched disc with a normal one.
Images are blurred or distorted when you start High-Speed
Search.
]Images are blurred or distorted at the point where the playback
speed changes and this is not a malfunction of the unit.
Playback does not start.
]Playback does not start for approximately 30 seconds after
recording is stopped and this is not a malfunction of the unit.
The unit does not operate.
Playback does not start when you select a title or a chapter.
● There are cases when the operation is prohibited on the disc.
● The Parental Lock is engaged and the disc is rated higher than
the set level.
]Release the Parental Lock temporarily or change the set level.
(墌 pg. 40)
● Lightning or static electricity may cause malfunction of the unit.
]Press 1 to turn the power off, then press the button again to
turn the power on.
The remote control of a JVC TV will not operate the unit.
● The setting of the remote control code is inappropriate.
]To operate the unit using a JVC TV remote control, set the
remote control code of the unit to “1” (Default: “3”). (墌 pg. 78)
Downloaded From DvDPlayer-Manual.com JVC Manuals
Playback (HDD Deck)
The HDD deck cannot be operated.
● The HDD deck is not selected.
]Press VHS/HDD/DVD SELECT on the unit repeatedly or HDD
on the remote so that the HDD lamp lights up on the unit.
90 EN TROUBLESHOOTING
Playback (VHS Deck)
Recording (HDD Deck)
The VHS deck cannot be operated.
TV broadcasts cannot be recorded.
● The VHS deck is not selected.
]Press VHS/HDD/DVD SELECT on the unit repeatedly or VHS
on the remote so that the VHS lamp lights up on the unit.
● “L-1” or “F-1” has been selected as the input mode.
]Set to the desired channel.
The tape will not rewind or fast-forward.
● The camcorder has not been properly connected.
]Confirm that the camcorder is properly connected.
● The input mode is not correct.
]Set the input mode to “F-1”. (墌 pg. 75)
● The tape is already fully rewound or fast-forwarded.
]Check the cassette.
The playback picture does not appear while the tape is running.
● The TV receiver’s channel selector is not set to the video
channel.
]If you are using the RF connection, set the TV receiver to the
video channel.
]If you are using the AV connection, the TV receiver is not set to
the AV mode.
● The unit’s video channel has not been correctly set.
]Perform the video channel set. (墌 pg. 19)
Noise appears during visual search.
● This is normal.
Camcorder recording is not possible.
Recording (VHS Deck)
During recording, the tape does not run. The VHS recording lamp
lights up on the unit.
● The unit is in the Record Pause mode.
Press 4 to resume recording.
Recording cannot be done.
● There is no cassette loaded, or the cassette loaded has had its
record safety tab removed.
]Insert a cassette, or using adhesive tape, cover the hole where
the tab was removed.
Noise appears during normal playback.
● The automatic tracking mode is engaged.
]Try manual tracking. (墌 pg. 52)
The playback picture is blurred or interrupted while TV
broadcasts are clear or “USE CLEANING CASSETTE” message
appears on the screen.
● The video heads may be dirty.
]Use a dry cleaning cassette TCL-3F, or consult your JVC dealer.
Breaks are noticeable in Hi-Fi soundtrack.
● The automatic tracking mode is engaged.
]Try manual tracking. (墌 pg. 52)
Recording (DVD Deck)
The desired program cannot be recorded.
● The channel position does not correspond to that in the
receiving area.
]Set the correct channel position for the receiving broadcast.
(墌 pg. 23)
Recording cannot be made.
● No disc or a disc not being compatible with the unit is loaded.
]Load a recordable disc on the unit. (墌 pg. 7)
● The disc loaded is not formatted.
]Format the disc. (墌 pg. 87)
● A finalized DVD-R disc is loaded.
]Recording cannot be made on finalized discs. Load a recordable
disc on the unit.
● The disc is full or does not have enough space for the title to be
recorded.
]Clear unnecessary titles on the disc or load a blank disc.
(墌 pg. 65)
● The DVD-RAM disc loaded has had its protect tab slid to the
protect position.
]Release the protect tab. (墌 pg. 10)
TV broadcasts cannot be recorded.
● “L-1” or “F-1” has been selected as the input mode.
]Set to the desired channel.
Camcorder recording is not possible.
● The camcorder has not been properly connected.
]Confirm that the camcorder is properly connected.
● The input mode is not correct.
]Set the input mode to “F-1”.
The tape is automatically rewound, then the unit is shut off.
● The end of the tape was reached during recording.
]The program may not have been recorded in its entirety. Next
time make sure you have enough time on the tape to record the
entire program.
Timer Recording (HDD & DVD Deck)
Timer programming cannot be made.
● Date and time is not correct.
]Set date and time correctly. (墌 pg. 22)
● Timer recording is in progress.
]Timer programming can’t be performed while a timer recording
is in progress. Wait until it finishes.
Timer programming recording does not start.
● Date and time is not correct.
]Set date and time correctly. (墌 pg. 22)
VCR Plus+ Timer Programming cannot be made.
● Date and time set on the unit is not correct.
]Set date and time correctly. (墌 pg. 22)
● The channel position does not correspond to that in the
receiving area.
]Set the correct channel position for the receiving broadcast.
(墌 pg. 23)
The VCR Plus+ system does not timer-record properly.
● The unit’s channel positions have been set incorrectly.
]Refer to “Changing VCR Plus+ Setting” (墌 pg. 86) and
reperform the procedure.
®
Downloaded From DvDPlayer-Manual.com JVC Manuals
TROUBLESHOOTING
Automatic Satellite Program Recording does not start.
The VCR Plus+ system does not timer-record properly.
● The DBS receiver is not connected properly to this unit.
]Connect the DBS receiver to the [VIDEO/AUDIO INPUT L1]
connectors properly. (墌 pg. 59)
● The unit’s channel positions have been set incorrectly.
]Refer to “Changing VCR Plus+ Setting” (墌 pg. 86) and
reperform the procedure.
On the front display panel, “– –:– –” appears.
Other Problems
● Power failure occurred.
]Set date and time correctly. (墌 pg. 22)
“PROGRAM FULL” appears on the TV screen during timer
programming.
● 32 programs have already been timer programmed.
]Clear unnecessary programs on the unit, then try timer
programming again. (墌 pg. 58)
The disc space does not increase when recorded titles are
cleared.
● The PC’s data recorded on a DVD-RAM drive cannot be cleared
on this unit.
]Format the disc. (When the disc is soiled, wipe the disc with a
soft dry cloth before formatting.) (墌 pg. 11, 87)
Timer Recording (VHS Deck)
EN
®
The image of the TV broadcast appears distorted on the TV
screen.
For RF/AV/S-video connection
]Press PROGRESSIVE SCAN for 3 or more seconds so that the
Video output indicator ( ) lights off on the front display panel.
For component video connection
]Press PROGRESSIVE SCAN for 3 or more seconds so that the
Video output indicator ( ) lights up on the front display panel.
Whistling or howling is heard from the TV during camcorder
recording.
● The camcorder’s microphone is too close to the TV.
]Position the camcorder so its microphone is away from the TV.
● The TV’s volume is too high.
]Turn the TV’s volume down.
Timer programming cannot be made.
When scanning channels, some of them are skipped over.
● Date and time is not correct.
]Set date and time correctly. (墌 pg. 22)
● The timer is not engaged.
]Press VHS TIMER and confirm that the VHS timer indicator
lights up on the front panel display.
● Timer recording is in progress.
]Timer programming can’t be performed while a timer recording
is in progress. Wait until it finishes.
● Those channels have been designated to be skipped.
]If you need the skipped channels, restore them. (墌 pg. 23)
Timer programming recording does not start.
Channel settings that were made manually seem to have
changed or disappeared.
● Date and time is not correct.
]Set date and time correctly. (墌 pg. 22)
● The timer is not engaged.
]Press VHS TIMER and confirm that the VHS timer indicator
lights up on the front panel display.
The VHS recording lamp on the unit won’t stop blinking.
● The timer is engaged but there’s no cassette loaded.
]Load a cassette with the record safety tab intact.
● The loaded cassette has had its record safety tab removed.
]Remove the cassette and cover the hole with adhesive tape, or
insert a cassette with the record safety tab intact.
The tape is automatically ejected, then the unit is shut off.
● The end of the tape was reached during timer recording.
]The program may not have been recorded in its entirety.
Next time make sure you have enough time on the tape to
record the entire program.
● The end of the tape was reached during Instant Timer
Recording.
]The program may not have been recorded in its entirety. Next
time make sure you have enough time on the tape to record the
entire program.
VCR Plus+ Timer Programming cannot be made.
● Date and time set on the unit is not correct.
]Set date and time correctly. (墌 pg. 22)
● The channel position does not correspond to that in the
receiving area.
]Set the correct channel position for the receiving broadcast.
(墌 pg. 23)
Downloaded From DvDPlayer-Manual.com JVC Manuals
91
The channel cannot be changed.
● Recording or Live Memory recording* is in progress.
]Press 9 to pause the recording, change channels, then press 4
to resume recording.
* HDD and DVD deck only
● After the manual settings were made, Auto Channel Set was
performed.
]Perform “Manual Clock Set” (墌 pg. 22).
Even though Auto or Semiauto Clock Set has been performed,
the clock is incorrect.
● The clock setting data received from the host channel is
incorrect.
]Select a different host channel during “Semiauto Clock Set”
(墌 pg. 22), or perform “Manual Clock Set” (墌 pg. 22).
Malfunction occurs and the unit cannot be power off.
]Reset the unit by disconnecting the AC power plug from the AC
outlet and connect again.
92 EN TROUBLESHOOTING
On-screen Message (HDD & DVD Deck Only)
DISC NOT REGISTERED IN THE LIBRARY
REGISTER DISC?
CAN NOT FINALIZE THIS DISC
● Finalizing is not complete since the disc may be dirty or
damaged. Take out the disc, clean it and retry. (墌 pg. 11, 88)
● A disc that is not registered in the library has been inserted.
Register the disc as necessary. (墌 pg. 68)
CAN NOT CANCEL FINALIZATION
OF THIS DISC
INSERT DISC XXXX
● Canceling disc finalization is not complete since the disc may be
dirty or damaged. Take out the disc, clean it and retry.
(墌 pg. 11, 88)
● Appears when a title that has been selected in the library is not
contained in the loaded disc.
PRESS [STOP] AGAIN TO STOP RECORDING
CAN NOT RECORD OR MAKE PLAY LIST
DELETE UNWANTED TITLES
● During Live Memory playback, 8 has been pressed. (墌 pg. 48)
● Recording and/or editing cannot be performed.
● The number of titles exceeds 99.
● The number of play lists exceeds 999.
● Timer recording has finished during Live Memory playback.
TIMER RECORDING COMPLETED
SET CLOCK BEFORE TIMER PROGRAMMING
PLAYBACK WILL STOP
THEN TIMER RECORDING WILL START
● To set the timer program, the clock must be set in advance.
(墌 pg. 22)
● Timer recording finished during Live Memory playback, then the
next timer recording is about to begin while playback continues.
PROGRAM FULL
DELETE UNWANTED TIMER PROGRAMS
COPY PROHIBITED
CAN NOT RECORD
● You can program this unit to timer-record as many as 32
programs. To program more, you need to cancel a timer
program already set. (墌 pg. 58)
● An attempt has been made to record copy-protected contents.
● An attempt has been made to record copy-once contents on a
disc that is not CPRM compatible, such as DVD-R.
DISC NOT LOADED
COPY PROHIBITED
CAN NOT PLAY
● Operation has been attempted when a disc is not loaded, or
loaded upside down. (墌 pg. 10)
DISC NOT RECORDABLE
INSERT RECORDABLE DISC
● When a playback-only disc or a finalized disc is loaded, 7 has
been pressed. (墌 pg. 7)
PLUSCODE NO. ERROR
CONFIRM PLUSCODE NO. THEN RETRY
● An invalid PlusCode number has been input. (墌 pg. 55)
GUIDE CHANNEL IS NOT SET
SET GUIDE CHANNEL THEN RETRY
● To set the timer program using the VCR Plus+ system, the
Guide Channel Number must be set in advance. (墌 pg. 86)
CAN NOT SET VCR PLUS TIMER PROGRAMMING DURING
TIMER RECORDING OR INSTANT TIMER RECORDING
● Appears when you tried to input a PlusCode number during
timer recording or instant timer recording.
REGION CODE ERROR
CHECK DISC
● A disc loaded cannot be played back on this unit since the
region number of the disc does not match that of the unit.
(墌 pg. 8)
UNREADABLE DISC
CHECK DISC
● When an incompatible disc is loaded, 4 has been pressed.
(墌 pg. 8)
COULD NOT FORMAT THE DISC
CHECK THE DISC
● Formatting is not complete since the disc may be dirty or
damaged. Take out the disc, clean it and retry. (墌 pg. 11, 87)
Downloaded From DvDPlayer-Manual.com JVC Manuals
● The unit has detected invalid contents at the start or in the
middle of playback.
THE i.LINK DEVICE THAT YOU HAVE CONNECTED IS NOT
RECOGNIZED
MAKE SURE THAT THE DEVICE IS CONNECTED PROPERLY
AND POWERED ON
● An attempt has been made to start DV dubbing when a digital
video camera is not properly connected to the unit.
● Check the connection. (墌 pg. 74)
SPECIFICATIONS
EN
93
GENERAL
VIDEO/AUDIO (VHS Deck)
Power requirement
AC 120 Vd, 60 Hz
Power consumption
Power on: 49 W
Power off: 16.2 W
Temperature
Operating: 5°C to 35°C (41°F to 95°F)
Storage: –20°C to 60°C (–4°F to 140°F)
Operating position
Horizontal only
Dimensions (WxHxD)
435 mm x 96 mm x 383 mm (17-3/16" x 3-4/5" x 15-1/13")
Weight
6.7 kg (14.8 lbs)
Input/Output
Video input: 0.5 – 2.0 Vp-p, 75 C (pin jack)
Audio input:
–8 dB, 50 kC (pin jack)
Corresponding to mono (left)
Audio output: –8 dB, 1 kC (pin jack)
RCA connectors:
IN x 3, OUT x 2
Input/Output (HDD & DVD Deck Only)
S-video input:
Y: 0.8 – 1.2 Vp-p, 75 C
C: 0.2 – 0.4 Vp-p, 75 C
S-video output:
Y: 1.0 Vp-p, 75 C
C: 0.3 Vp-p, 75 C
i.Link: 4-pin for DV input
Component video output:
Y: 1.0 Vp-p, 75 C
CB/CR, PB/PR : 0.7 Vp-p, 75 C
Corresponding to copy protection
Cable Box: R3.5mm
Digital audio output:
Optical: –18 dBm, 660 nm
Coaxial: 0.7 Vp-p, 75 C
Corresponding to Dolby Digital and DTS Digital Surround
Bit stream
Selectable in digital audio output setting menu
Signal system
NTSC color signal and EIA monochrome signal, 525 lines/60 fields
Recording system
DA4 (Double Azimuth) head helical scan system
Format
VHS NTSC standard
Maximum recording time
(SP): 210 min. with ST-210 video cassette
(EP): 630 min. with ST-210 video cassette
Signal-to-noise ratio
45 dB
Horizontal resolution
230 lines
Frequency range
(Normal audio): 70 Hz to 10,000 Hz
(Hi-Fi audio): 20 Hz to 20,000 Hz
VIDEO/AUDIO (DVD Deck)
Recording time
Maximum 8 hours (with 4.7 GB disc)
(XP): Approx. 1 hour
(SP): Approx. 2 hours
(LP): Approx. 4 hours
(EP): Approx. 6 hours
(FR): Approx. 1 hour – 8 hours
Audio recording system
Dolby Digital (2 ch)
Linear PCM (XP mode only)
Video recording compression system
MPEG2 (CBR/VBR)
VIDEO/AUDIO (HDD Deck)
Video recording compression system
MPEG2 (VBR)
Audio recording system
Dolby Digital (2 ch)
Linear PCM (XP mode only)
Recording time
Maximum 147 hours (with 80 GB HDD)
(XP): Approx. 18 hours
(SP): Approx. 35 hours
(LP): Approx. 70 hours
(EP): Approx. 105 hours
(FR): Approx. 18 – 147 hours
Downloaded From DvDPlayer-Manual.com JVC Manuals
Specifications shown are for SP mode unless otherwise specified.
TUNER/TIMER
Tuning system
Frequency synthesized tuner
Channel coverage
VHF: Channels 2 – 13
UHF: Channels 14 – 69
CATV: 113 Channels
RF output
Channel 3 or 4 (Switchable; preset to Channel 3 when shipped)
75 C, unbalanced
Memory backup time
Approx. 60 minutes
ACCESSORIES
Provided accessories
RF cable x 1,
Audio/Video cable,
Satellite Controller,
Infrared remote control unit,
“AA” battery x 2
E.& O.E. Design and specifications subject to change without
notice.
ATTENTION:
This unit contains microcomputers. External electronic noise or
interference could cause malfunctioning. In such cases, switch the
unit off and unplug the AC power cord. Then plug it in again and turn
the unit on. Take out the disc. After checking the disc, operate the
unit as usual.
94 EN APPENDIX
Language Code List
AA
Afar
IK
Inupiak
RN
Kirundi
AB
Abkhazian
IN
Indonesian
RO
Rumanian
AF
Afrikaans
IS
Icelandic
RU
Russian
AM
Ameharic
IW
Hebrew
RW
Kinyarwanda
AR
Arabic
JI
Yiddish
SA
Sanskrit
AS
Assamese
JW
Javanese
SD
Sindhi
AY
Aymara
KA
Georgian
SG
Sangho
AZ
Azerbaijani
KK
Kazakh
SH
Serbo-Croatian
BA
Bashkir
KL
Greenlandic
SI
Singhalese
BE
Byelorussian
KM
Cambodian
SK
Slovak
BG
Bulgarian
KN
Kannada
SL
Slovenian
BH
Bihari
KO
Korean (KOR)
SM
Samoan
BI
Bislama
KS
Kashmiri
SN
Shona
BN
Bengali, Bangla
KU
Kurdish
SO
Somali
BO
Tibetan
KY
Kirghiz
SQ
Albanian
BR
Breton
LA
Latin
SR
Serbian
CA
Catalan
LN
Lingala
SS
Siswati
CO
Corsican
LO
Laothian
ST
Sesotho
CS
Czech
LT
Lithuanian
SU
Sundanese
CY
Welsh
LV
Latvian, Lettish
SW
Swahili
DZ
Bhutani
MG
Malagasy
TA
Tamil
EL
Greek
MI
Maori
TE
Telugu
EO
Esperanto
MK
Macedonian
TG
Tajik
ET
Estonian
ML
Malayalam
TH
Thai
EU
Basque
MN
Mongolian
TI
Tigrinya
FA
Persian
MO
Moldavian
TK
Turkmen
FJ
Fiji
MR
Marathi
TL
Tagalog
FO
Faroese
MS
Malay (MAY)
TN
Setswana
FY
Frisian
MT
Maltese
TO
Tonga
GA
Irish
MY
Burmese
TR
Turkish
GD
Scots Gaelic
NA
Nauru
TS
Tsonga
GL
Galician
NE
Nepali
TT
Tatar
GN
Guarani
OC
Occitan
TW
Twi
GU
Gujarati
OM
(Afan) Oromo
UK
Ukrainian
HA
Hausa
OR
Oriya
UR
Urdu
HI
Hindi
PA
Panjabi
UZ
Uzbek
HR
Croatian
PL
Polish
VI
Vietnamese
HU
Hungarian
PS
Pashto, Pushto
VO
Volapuk
HY
Armenian
PT
Portuguese
WO
Wolof
IA
Interlingua
QU
Quechua
XH
Xhosa
IE
Interlingue
RM
Rhaeto-Romance
YO
Yoruba
ZU
Zulu
Downloaded From DvDPlayer-Manual.com JVC Manuals
APPENDIX
EN
Country/Area Code List for Parental Lock
AD
Andorra
CK
Cook Islands
GN
Guinea
AE
United Arab Emirates
CL
Chile
GP
Guadeloupe
AF
Afghanistan
CM
Cameroon
GQ
Equatorial Guinea
AG
Antigua and Barbuda
CN
China
GR
Greece
AI
Anguilla
CO
Colombia
GS
South Georgia and the South
Sandwich Islands
AL
Albania
CR
Costa Rica
GT
Guatemala
AM
Armenia
CU
Cuba
GU
Guam
AN
Netherlands Antilles
CV
Cape Verde
GW
Guinea-Bissau
AO
Angola
CX
Christmas Island
GY
Guyana
AQ
Antarctica
CY
Cyprus
HK
Hong Kong
AR
Argentina
CZ
Czech Republic
HM
Heard Island and McDonald
Islands
AS
American Samoa
DE
Germany
HN
Honduras
AT
Austria
DJ
Djibouti
HR
Croatia
AU
Australia
DK
Denmark
HT
Haiti
AW
Aruba
DM
Dominica
HU
Hungary
AZ
Azerbaijan
DO
Dominican Republic
ID
Indonesia
BA
Bosnia and Herzegovina
DZ
Algeria
IE
Ireland
BB
Barbados
EC
Ecuador
IL
Israel
BD
Bangladesh
EE
Estonia
IN
India
BE
Belgium
EG
Egypt
IO
British Indian Ocean Territory
BF
Burkina Faso
EH
Western Sahara
IQ
Iraq
BG
Bulgaria
ER
Eritrea
IR
Iran (Islamic Republic of)
BH
Bahrain
ES
Spain
IS
Iceland
BI
Burundi
ET
Ethiopia
IT
Italy
BJ
Benin
FI
Finland
JM
Jamaica
BM
Bermuda
FJ
Fiji
JO
Jordan
BN
Brunei Darussalam
FK
Falkland Islands (Malvinas)
JP
Japan
BO
Bolivia
FM
Micronesia
(Federated States of)
KE
Kenya
BR
Brazil
FO
Faroe Islands
KG
Kyrgyzstan
BS
Bahamas
FR
France
KH
Cambodia
BT
Bhutan
FX
France, Metropolitan
KI
Kiribati
BV
Bouvet Island
GA
Gabon
KM
Comoros
BW
Botswana
GB
United Kingdom
KN
Saint Kitts and Nevis
BY
Belarus
GD
Grenada
KP
Korea, Democratic People’s
Republic of
BZ
Belize
GE
Georgia
KR
Korea, Republic of
CA
Canada
GF
French Guiana
KW
Kuwait
CC
Cocos (Keeling) Islands
GH
Ghana
KY
Cayman Islands
CF
Central African Republic
GI
Gibraltar
KZ
Kazakhstan
CG
Congo
GL
Greenland
LA
Lao People’s Democratic
Republic
CH
Switzerland
GM
Gambia
LB
Lebanon
CI
Côte d’Ivoire
Downloaded From DvDPlayer-Manual.com JVC Manuals
95
96
EN
APPENDIX
LC
Saint Lucia
NU
Niue
SZ
Swaziland
LI
Liechtenstein
NZ
New Zealand
TC
Turks and Caicos Islands
LK
Sri Lanka
OM
Oman
TD
Chad
LR
Liberia
PA
Panama
TF
French Southern Territories
LS
Lesotho
PE
Peru
TG
Togo
LT
Lithuania
PF
French Polynesia
TH
Thailand
LU
Luxembourg
PG
Papua New Guinea
TJ
Tajikistan
LV
Latvia
PH
Philippines
TK
Tokelau
LY
Libyan Arab Jamahiriya
PK
Pakistan
TM
Turkmenistan
MA
Morocco
PL
Poland
TN
Tunisia
MC
Monaco
PM
Saint Pierre and Miquelon
TO
Tonga
MD
Moldova, Republic of
PN
Pitcairn
TP
East Timor
MG
Madagascar
PR
Puerto Rico
TR
Turkey
MH
Marshall Islands
PT
Portugal
TT
Trinidad and Tobago
ML
Mali
PW
Palau
TV
Tuvalu
MM
Myanmar
PY
Paraguay
TW
Taiwan
MN
Mongolia
QA
Qatar
TZ
Tanzania, United Republic of
MO
Macau
RE
Réunion
UA
Ukraine
MP
Northern Mariana Islands
RO
Romania
UG
Uganda
MQ
Martinique
RU
Russian Federation
UM
United States Minor Outlying
Islands
MR
Mauritania
RW
Rwanda
US
United States
MS
Montserrat
SA
Saudi Arabia
UY
Uruguay
MT
Malta
SB
Solomon Islands
UZ
Uzbekistan
MU
Mauritius
SC
Seychelles
VA
Vatican City State (Holy See)
MV
Maldives
SD
Sudan
VC
Saint Vincent and the
Grenadines
MW
Malawi
SE
Sweden
VE
Venezuela
MX
Mexico
SG
Singapore
VG
Virgin Islands (British)
MY
Malaysia
SH
Saint Helena
VI
Virgin Islands (U.S.)
MZ
Mozambique
SI
Slovenia
VN
Viet Nam
NA
Namibia
SJ
Svalbard and Jan Mayen
VU
Vanuatu
NC
New Caledonia
SK
Slovakia
WF
Wallis and Futuna Islands
NE
Niger
SL
Sierra Leone
WS
Samoa
NF
Norfolk Island
SM
San Marino
YE
Yemen
NG
Nigeria
SN
Senegal
YT
Mayotte
NI
Nicaragua
SO
Somalia
YU
Yugoslavia
NL
Netherlands
SR
Suriname
ZA
South Africa
NO
Norway
ST
Sao Tome and Principe
ZM
Zambia
NP
Nepal
SV
El Salvador
ZR
Zaire
NR
Nauru
SY
Syrian Arab Republic
ZW
Zimbabwe
Downloaded From DvDPlayer-Manual.com JVC Manuals
LIST OF TERMS
EN
97
A
O
A-B Repeat Playback ................................................ 37
Accidental erasure prevention .................................... 54
Adjusting The Picture Quality ..................................... 38
Angle Selection ........................................................ 30
Audio Channel Selection ........................................... 31
Audio Language/Sound Selection ............................... 31
Auto Channel Set ..................................................... 23
Auto Daylight Saving Time ........................................ 22
One Touch Replay .............................................. 35, 49
On-screen Bar .......................................................... 36
On-screen Language Set ........................................... 21
P
C
Pan&Scan ................................................................ 26
Play List ................................................................... 66
Playback Control (PBC) ............................................. 31
Program Playback .................................................... 39
Progressive scan ...................................................... 83
Cancel And Change Programs ..............................58, 62
Check Programs ..................................................58, 62
Country/Area Code List for Parental Lock .................... 95
Quick Rewind A Little ................................................ 51
D
Disc menu ............................................................... 28
Disc Remaining Time ...........................................42, 45
Disc Resume ........................................................... 82
Discs For Playback Only ............................................. 8
DVD menu ............................................................... 28
E
Elapsed Recording Time Indication ................. 42, 45, 54
F
File Structure Of Discs ................................................ 9
Free Rate Function ................................................... 43
G
Guide Program Number ............................................ 86
H
High-Speed Search ....................................... 28, 46, 51
I
Index Search ............................................................ 51
Instant Timer Recording (ITR) ......................... 42, 45, 54
Interlaced scan ......................................................... 83
J
Jump Search ............................................................ 49
L
Language Code List .................................................. 94
Letter Box ................................................................ 26
Live Memory .......................................................32, 47
Live Memory Recording ............................................ 49
M
Manual Channel Set ................................................. 23
Manual Clock Set ..................................................... 22
Manual Tracking ....................................................... 52
Marking Positions To Play Back Again Later ................ 29
Menu/Audio/Subtitle Language Set ............................. 21
N
Next Function Memory .............................................. 52
Downloaded From DvDPlayer-Manual.com JVC Manuals
Q
R
Random Playback ..................................................... 39
Recordable/playable discs ........................................... 7
Recording Medium And Format .................................... 9
Recording Mode ................................................. 41, 44
Recording Resume Function ...................................... 53
Region Number .......................................................... 8
Register Disc ............................................................ 68
Relief Recording ....................................................... 57
Repeat Playback ................................................ 37, 52
Resume Function ..................................................... 29
S
SAP ............................................................. 43, 45, 54
Second Audio Recording ................................ 43, 45, 54
Select The Switching Interval Of The Slide Show ......... 39
Semiauto Clock Set .................................................. 22
Setting The Progressive Mode ................................... 39
Simulated Surround Effect ......................................... 38
Skip Search ..................................................29, 46, 51
Slow Motion ..................................................29, 46, 51
Soundtrack Selection ................................................ 52
Still Picture/Frame-By-Frame Playback ............29, 46, 51
Subtitle Selection ...................................................... 30
T
Tape Position Indicator .............................................. 18
Tape Remaining Time ............................................... 54
Temporary Recording ................................................ 47
Time Search ............................................................ 38
Top menu ................................................................ 28
U
Unplayable Discs ........................................................ 8
Usable cassettes ...................................................... 50
V
VHS Progressive Scan .............................................. 52
W
Weekly/Daily Recording ............................................ 56
When Programs Overlap Each Other .................... 58, 62
98
EN
WARRANTY (Only in U.S.A.)
Downloaded From DvDPlayer-Manual.com JVC Manuals
MEMO
Downloaded From DvDPlayer-Manual.com JVC Manuals
EN
99
100
EN
FOR SERVICING (Only in U.S.A.)
DR-MX1S
© 2004 Victor Company of Japan, Limited
Downloaded From DvDPlayer-Manual.com JVC Manuals
Printed in China
US 1104MNH-SW-BJ
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement