Evaluation Board User Guide UG-174
Evaluation Board User Guide
UG-174
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluation Kit for the ADM2914 and the ADM12914
When monitoring negative supplies, it has a 1 V buffered
reference output that can be used. The tristate SEL pin is used to
configure the polarity of the third and fourth inputs that determine
if they are used for monitoring positive or negative supplies.
FEATURES
Input voltage of 8 V to 20 V
6 adjustable input voltages including 2 negative
Full features evaluated on a single board
LED indicated voltage and output status
Configurations can be easily adjusted with bare hands
Development area allows custom add-on circuits
Test points for easy probing
The ADM2914 and ADM12914 are available in two models: the
ADM2914-1/ADM12914-1 and the ADM2914-2/ADM12914-2.
•
•
PACKAGE CONTENTS
EVAL-ADM2914EBZ evaluation board
GENERAL DESCRIPTION
The ADM2914/ADM12914 are quad voltage monitoring devices
designed to simultaneously monitor undervoltage and overvoltage
conditions on up to four supply rails. There are four undervoltage
and four overvoltage comparators integrated internally to provide
common UV and OV output signals. This device integrates the
required comparators and digital gating necessary to achieve single
common UV and OV reset signals. Each input is compared with a
0.5 V reference. Users can program the monitoring voltage level
through the external voltage dividers.
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
The ADM2914-1/ADM12914-1 offer a latching OV output
that can be cleared by toggling the LATCH input pin.
The ADM2914-2/ADM12914-2 have a disable pin that is
used as an override to disable both outputs signals.
An internal shunt regulator enables the ADM2914/ADM12914
devices to be used on higher voltage systems. However, this
requires a resistor to be placed between the main supply rail
and the VCC pin to limit the current flow into the VCC pin to no
greater than 10 mA.
This evaluation board is designed to fully evaluate the features
of the ADM2914 and the ADM12914, including supply monitoring
for both positive and negative rails, monitoring polarity selection,
timer function, and LATCH/DIS functions.
Rev. 0 | Page 1 of 12
UG-174
Evaluation Board User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1
Evaluation Board Overview .............................................................5
Package Contents .............................................................................. 1
Evaluation Board Schematics...........................................................6
General Description ......................................................................... 1
Ordering Information .................................................................... 10
Revision History ............................................................................... 2
Bill of Materials ........................................................................... 10
Evaluation Board Hardware ............................................................ 3
Switch, Jumper, LED, and Connector Functions ..................... 3
REVISION HISTORY
6/10—Revision 0: Initial Version
Rev. 0 | Page 2 of 12
Evaluation Board User Guide
UG-174
EVALUATION BOARD HARDWARE
SWITCH, JUMPER, LED, AND CONNECTOR FUNCTIONS
Table 1. Switch Functions
Switch
S1
S2
ADM2914-1
ADM2914-2
S3
S3-1
S3-2
S3-3
S3-4
S4
S5
Description
Input polarity selection switch.
6V2 = all inputs positive.
N/C = V1 to V3 positive and V4 negative.
GND = V1 and V2 positive, and V3 and V4 negative.
LATCH/DIS control switch.
6V2 = OV output not latched/clear latched OV output.
GND = OV output latched.
6V2 = disable outputs, OV and UV outputs are not asserted except UVLO.
GND = enable outputs.
Timer capacitor control switch.
Connect the TIMER pin to C7 and C16.
On = connect.
Off = disconnect.
Connect the TIMER pin to C15.
On = connect.
Off = disconnect.
Connect the TIMER pin to C14.
On = connect.
Off = disconnect.
Connect the TIMER pin to VCC.
On = connect.
Off = disconnect.
IC input selection.
Main supply = connect the VCC pin of the ADM2914 to the main input of the board. This requires the
shunt resistor RSHUNT to be placed.
5 V = Connect the VCC pin of the ADM2914 to the output of U3 (adjustable 5 V).
Input selection switch.
+/+ = The inputs of the ADM2914 are connected to monitors adjustable 1 V, 2.5 V, 3.3 V, and 5 V.
+/− = The inputs of the ADM2914 are connected to monitors adjustable +1 V, +2.5 V, +3.3 V, and −5 V.
−/− = The inputs of the ADM2914 are connected to monitors adjustable +1 V, +2.5 V, −3.3 V, and −5 V.
Default
6V2
6V2
GND
Disconnected
Connected
Disconnected
Disconnected
5V
+/+
Table 2. Jumper Functions
Jumper
J9
J10
J2
J4
J6
J5
Description
Deassert to disable the adjustable 1 V output.
Deassert to disable the adjustable 2.5 V output.
Deassert to disable the adjustable 3.3 V output. Disabling the 3.3 V output also disables the −3.3 V,
+2.5 V, and +1 V outputs.
Deassert to disable the adjustable 5 V output. Disabling the 5 V output may disable the input supply to
the ADM2914 unless it is powered from the main supply.
Deassert to disable the adjustable −5 V output.
Deassert to disable the adjustable −3.3 V output.
Rev. 0 | Page 3 of 12
Default
Asserted
Asserted
Asserted
Asserted
Asserted
Asserted
UG-174
Evaluation Board User Guide
Table 3. LED Functions
LED
D6
D7
D8
D4
D3
D2
D1
Corresponding Node
6V2
1V
2.5V
3.3V
5V
OV
UV
Description
The LEDs used to indicate the status of the on-board voltage rails.
The LEDs used to indicate the status of the on-board voltage rails.
The LEDs used to indicate the status of the on-board voltage rails.
The LEDs used to indicate the status of the on-board voltage rails.
The LEDs used to indicate the status of the on-board voltage rails.
The LEDs used to indicate the status of the ADM2914 outputs.
The LEDs used to indicate the status of the ADM2914 outputs.
Table 4. Connector Functions
Connector
J1
J3
Description
Input power connector. Connect J1 to the 8.5 V to 20 V voltage source.
Input power connector for wall adaptor. Connect J3 to the 8.5 V to 20 V power adaptor. Tip negative.
Rev. 0 | Page 4 of 12
Evaluation Board User Guide
UG-174
09186-001
EVALUATION BOARD OVERVIEW
Figure 1. Evaluation Board
8.5V~20V INPUT
+1V ADJUSTABLE
RESISTOR
DIVIDER
+2.5V ADJUSTABLE
RESISTOR
DIVIDER
ADP1712
LM78L62
ADP1712
6.2V
ADM2914
ADP3334
–3.3V ADJUSTABLE
ADM8828
+5V ADJUSTABLE
ADP3334
–5V ADJUSTABLE
ADM8660
RESISTOR
DIVIDER
RESISTOR
DIVIDER
RESISTOR
DIVIDER
RESISTOR
DIVIDER
Figure 2. Evaluation Board Power Architecture
Rev. 0 | Page 5 of 12
ADM12914
09186-002
+3.3V ADJUSTABLE
UG-174
Evaluation Board User Guide
EVALUATION BOARD SCHEMATICS
09186-003
Figure 3. Evaluation Board Schematic 1
Rev. 0 | Page 6 of 12
Evaluation Board User Guide
UG-174
09186-004
Figure 4. Evaluation Board Schematic 2
Rev. 0 | Page 7 of 12
UG-174
Evaluation Board User Guide
09186-005
Figure 5. Evaluation Board Schematic 3
Rev. 0 | Page 8 of 12
Evaluation Board User Guide
UG-174
09186-006
Figure 6. Evaluation Board Schematic 4
Rev. 0 | Page 9 of 12
UG-174
Evaluation Board User Guide
ORDERING INFORMATION
BILL OF MATERIALS
Table 5.
Name
−3V3, −5V, LATCH/DIS, OV, UV, 1V, 2V5, 3V3, 5V,
6V2, REF, REG4FB, REG4FB1, REG4IN, REG4IN2,
SEL, TMR, VCC, VH1 to VH4, VL1 to VL4
C1
C2, C3
C4, C5
C7
C8 to C10, C12
C11, C13, C19, C22
C14
C15
C16
C34
D1 to D4, D6 to D8
GND
J1
J2, J4 to J6, J9, J10
J3
Q1 to Q6
R1, R44, R45
R2
R3 to R5, R1,1 R29, R34
R6
R7, R12, R14, R28, R30, R33, R35, R40 to R43
R8
R9
R10
R13
R15
R16
R17
R18, R23
R19
R20
R21, R24
R22
R25
R26
R27
R31
R32
R36, R39
Part Description
Red test point
Part Number
20-313137
Stock Code
FEC 873 1144
Capacitor, 0.33 μF, 1206, 10%, 25 V
50 V electrolytic capacitor, Case B,
low ESR, 1 μF, 20%
16 V electrolytic capacitor, Case B,
10 μF, 20%
0805, capacitor footprint
(not inserted), user defined
Capacitor, 0805, 2.2 μF, 10 V, X7R, ±10%
Capacitor, 0603, 1μF, 10 V
Capacitor, 0805, 10 pF, 100 V, 5%
Capacitor, 0805, 1 nF, 50 V, 5%
Through-hole capacitor
(not inserted), user defined
Capacitor, 0805, 0.01 μF, 10%
Green, 0805, chip LED
Red test point
2-pin terminal block (5 mm pitch)
2-pin (0.1" pitch) header and
shorting shunt, jumper socket red
2.1 mm, dc barrel power connector
General-purpose NPN SMD transistor,
BC850C, SOT-23
51 kΩ resistor, 0805, ±1%
220 kΩ resistor, 0805, ±1%
100 kΩ resistor, 0805, ±5%
604 kΩ resistor, 0805, ±0.1%
1 kΩ resistor, 0.1 W, 0805, ±1%
51.1 kΩ resistor, 0603, ±0.1%
49.9 kΩ resistor, 0805, ±1%
120 kΩ resistor, 0805, ±1%
3.6 kΩ resistor, 0805, ±1%
9.31 kΩ resistor, 0805, ±0.1%
357 kΩ resistor, 0805, ±0.1%
634 kΩ resistor, 0805, ±0.1%
14.3 kΩ resistor, 0603, ±0.1%
7.32 kΩ resistor, 0805, ±0.1%
44.2 kΩ resistor, 0805, ±0.1%
64.9 kΩ resistor, 0603, ±0.1%
392 kΩ resistor, 0805, ±0.1%
162 kΩ resistor, 0603, ±0.1%
8.2 kΩ resistor, 0805, ±1%
4.12 kΩ resistor, 0805, ±0.1%
11.8 kΩ resistor, 125 mW, ±1%
29.4 kΩ resistor, 125 mW, ±1%
39.2 kΩ resistor, 0603, ±0.1%
C1206C334K3RACTU
EEEFC1H1R0R
FEC 1650900
FEC 9694528
EEEFK1C100R
FEC 9695648
Not inserted
Not inserted
CC0805KKX7R6BB225
CC0603ZRY5V6BB105
MCCA000390
08055A102JAT2A
Not inserted
FEC 9402152
FEC 3188840
FEC 9406239
FEC 317457
Insert low profile sockets
CC0805KRX7R8BB103
KP-2012SGC
20-313137
M20-9990246 and
M7566-05
DC10A
BC850C
FEC 3019767
FEC 1318243
FEC 8731144
FEC 151-785
FEC 1022247 and
FEC 150411
FEC 224959
FEC 1081241
MC 0.1W 0805 1% 51K
MC 0.1W 0805 1% 220K
RC0805JR-07100KL
MCTC0525B6043T5E
WCR0805-1K0FI
PCF0603R 51K1BI.T1
CRCW080549K9FKEA
MC 0.1W 0805 1% 120K
MC 0.1W 0805 1% 3K6
MCTC0525B9311T5E
PCF0805R-357KBT1
PCF0805R 634KBI.T1
PCF0603R-14K3BT1
PCF0805R 7K32BI.T1
PCF0805R-44K2BT1
PCF0603R-64K9BT1
PCF0805R 392KBI.T1
PCF0603R-162KBT1
MC 0.1W 0805 1% 8K2
PCF0805R-4K12BT1
CRCW080511K8FKEA
CRCW080529K4FKEA
PCF0603R-39K2BT1
FEC 9333339
FEC 9332839
FEC 9234250
FEC 1576103
FEC 1099800
FEC 1160386
FEC 1469934
FEC 9332510
FEC 9333118
FEC 1575897
FEC 1353265
FEC 1160299
FEC 1353120
FEC 1160193
FEC 1353276
FEC 1353180
FEC 1160287
FEC 1353121
FEC 9333584
FEC 1353280
FEC 1258438
FEC 1152323
FEC 1353166
Rev. 0 | Page 10 of 12
Evaluation Board User Guide
Name
R37
R38
R_SHUNT
S1
S2, S4
S3
S5
U1
U2, U3
U4
U5
U6, U7
U8
U9
VR1, VR2, VR4
VR3
X1 to X16
UG-174
Part Description
39 kΩ resistor, 0603, ±0.1%
4.32 kΩ resistor, 0603, ±0.1%
Resistor, 1206
Slide switch, SP 3 POS, VERT
Slide switch, SP 2 POS, VERT
4-way SMD switch (SW\4DIP)
Switch slide 4P3T, 30 V, right angle
ADM8828, switched-capacitor voltage
inverter with shutdown, SOT-23-6
ADP3334 adjustable LDO regulator,
MSOP-8
ADM8660, CMOS switched-capacitor
voltage converter SOIC-8
6.2 V voltage regulator, 78L62, TO-92-3
ADP1712 adjustable LDO, TSOT-5
ADM2914, 16-lead QSOP
4-channel supervisory circuit
footprint, QSOP-16
50 kΩ trimmer
5 kΩ trimmer
Patchwork area, keep holes
free of solder
Rev. 0 | Page 11 of 12
Part Number
ERA3AEB393V
PCF0603R 4K32BI.T1
Not populated
STSSS9131
STSSS9121
A6S-4101
EG4319
ADM8828ARTZ
Stock Code
FEC 1577627
FEC 1160343
Not applicable
FEC 1123876
FEC 1123875
FEC 9901868
Digi-Key EG1915-ND
ADM8828ARTZ
ADP3334ARMZ
ADP3334ARMZ
ADM8660ARZ
ADM8660ARZ
LM78L62ACZ
ADP1712AUJZ-R7
OTS-16(28)-0.635-02
Not populated
FEC 9490213
ADP1712AUJZ-R7
Abrel OTS-16(28)-0.635-02
Not applicable
M63M503KB30T607
M63M502KB30T607
Not applicable
FEC 9608257
FEC 9608222
Not applicable
UG-174
Evaluation Board User Guide
NOTES
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2010 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG09186-0-6/10(0)
Rev. 0 | Page 12 of 12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement