2016-acura-tlx-19-inch-aluminum

2016-acura-tlx-19-inch-aluminum
INSTALLATION
INSTRUCTIONS
Accessory
Application
19” ALUMINUM WHEEL
P/N 08W19-TZ3-200
2016 TLX
PARTS LIST
Publications No.
VERSION 1
Issue Date
SEP 2015
Parts for TPMS sensor assembly
Tire pressure sensor assembly
Aluminum wheel
(The illustration may differ from the actual wheel.)
Wheel center cap
(The illustration may differ from the actual center cap.)
Washer
Valve nut
Tire and loading information label A
(May not used)
TOOLS AND SUPPLIES REQUIRED
Tire and loading information label B
(May not used)
Ratchet
11 mm and 19 mm Sockets
Torque wrench
Isopropyl alcohol
Shop towel
SPECIFICATIONS
Accessory User’s Information Manual
Rim size
19 x 8 J (inset 50)
Tire size
245/40R19 98W
Bolt hole PCD
114.3 (5 holes)
Tire pressure
© 2015 American Honda Motor Co., Inc. – All Rights Reserved.
BII02265-12 (1509)
Front
220 kPa
(2.2 kgf/cm2, 32 psi)
Rear
220 kPa
(2.2 kgf/cm2, 32 psi)
08W19-TZ3-2000-90
1 of 3
INSTALLATION
1.
Client Information: The information in this installation
instruction is intended for use only by skilled
technicians who have the proper tools, equipment, and
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
NOTE:
• This aluminum wheel is designed for use on a vehicle
equipped with TPMS (Tire Pressure Monitoring
System).
• This aluminum wheel is equipped with a TPMS sensor.
See the Service Manual for the tire replacement and
TPMS sensor installation procedures.
• The illustrations of the aluminum wheels are shown for
reference purposes only.
• Install the correct size tire.
• Follow the instructions in the Owner’s Manual when
raising the vehicle, and when removing and installing
the wheels. Do not overtighten the wheel nuts.
Wheel nut torque: 108 N·m (11 kgf·m, 80 lbf·ft).
• Use a tire changer to install and remove the tires per
the directions in the Operation Manual furnished with
the tire changer. Do not use a tire lever to install and
remove the tires as it may cause damage to the tire and
aluminum wheel.
• To allow the adhesive to cure, do not wash the
vehicle for 24 hours. Please advise the client.
Before installing the tire pressure sensor, clean the
mating surface on the sensor and the aluminum
wheel.
Slide down.
OUTSIDE
ALUMINUM
WHEEL
TIRE
PRESSURE
SENSOR
VALVE NUT
Tightening torque:
8.0 N·m
(0.8 kgf·m, 5.9 lbf·ft)
Hold it tight.
WASHER
QC02312AA
2.
3.
2 of 3
BII02265-12 (1509)
Install the tire pressure sensor and the washer on
the aluminum wheel, and tighten the valve nut finger
tight. Make sure the pressure sensor is resting on the
wheel.
While holding the tire pressure sensor against the
wheel, torque the valve nut to 8.0 N·m
(0.8 kgf·m, 5.9 lbf·ft)
© 2015 American Honda Motor Co., Inc. – All Rights Reserved.
NOTE:
• Check the grommet on the tire pressure sensor to
make sure it is seated properly.
• Make sure the valve stem does not protrude into the
sensor housing surface.
• To prevent the sensor housing from getting caught on
the bead of the tire, install the tire pressure sensor so
that the sensor housing does not protrude into the bead
area of the wheel.
• Do not reuse a grommet that was previously tightened,
as it is deformed inside.
• Do not use pneumatic or electric tools on the valve nut.
• Tightening the nut above the specified torque can
damage the grommet.
TIRE AND LOAD INFORMATION LABEL
Install the new label in the driver's doorjamb:
1. Open the driver's door. Using isopropyl alcohol on a
shop towel, clean the standard tire label.
2. Check the spare tire specification, and choose the new
label (A or B) that matches the specification.
3. Attach the new label over the standard label as shown.
ACCESSORY
TIRE AND LOADING
INFORMATION
LABEL A OR B
STANDARD
TIRE AND LOADING
INFORMATION LABEL
(Clean with
isopropyl alcohol.)
SECTION VIEW
PROTRUSION
OF WHEEL
WASHER
GROMMET
Make sure to contact
as shown.
VALVE
NUT
Make sure there is
no gap in this area.
TIRE PRESSURE SENSOR HOUSING
SURFACE
PROTRUSION SENSOR
OF WHEEL
ADHESIVE
BACKING
(Remove.)
DRIVER’S
DOOR JAMB
QC02313AA
USE AND CARE
• Use a neutral detergent to clean the wheels.
• Rinse off the neutral detergent promptly after
cleaning the wheels.
VALVE STEM
(Make sure not to protrude into
the sensor housing surface.)
VIEW FROM THE INSIDE OF
THE ALUMINUM WHEEL
930404BR
4.
5.
6.
Install the tires according to the Service Manual.
Install the wheels on the vehicle and torque to
108 N·m (11 kgf·m, 80 lbf·ft).
Drive the vehicle for at least 40 seconds at a speed
of 24 km/h (15 mph) or more. All sensor IDs will be
memorized automatically.
© 2015 American Honda Motor Co., Inc. – All Rights Reserved.
BII02265-12 (1509)
3 of 3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement