Entone URC PLUS universal remote control User’s Guide

Universal Remote Control
URC PLUS
User’s Guide
COPYRIGHT
©2007 Entone, Inc. All rights reserved. This document contains proprietary
information protected by copyright. No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in any form or by any means,
electronic, mechanical, photocopying, recording or otherwise, without the prior
written consent of Entone, Inc., 2755 Campus Drive, Suite 235, San Mateo, CA
94403. U.S.A.
DISCLAIMER
IF THIS PRODUCT DIRECTS YOU TO COPY MATERIALS, YOU MUST HAVE
PERMISSION FROM THE COPYRIGHT OWNER OF THE MATERIALS TO AVOID
VIOLATING THE LAW WHICH COULD RESULT IN DAMAGES OR OTHER REMEDIES.
TRADEMARKS
Entone and the tagline “Connecting the Home” are trademarks of Entone, Inc. All
other trademarks or registered trademarks belong to their respective owners.
CHANGES
The material in this document is for information only and is subject to change
without notice. While reasonable efforts have been made in the preparation of this
document to assure its accuracy, Entone, Inc. assumes no liability resulting from
the use of the information contained herein.
Entone, Inc. reserves the right to make changes in the product design without
reservation and without notification to its users.
P/N: HYDRA_UG 1.0
CUSTOMER SUPPORT AND CONTACT INFORMATION
For Customer Support please call: 650.572.7000
Customer Contact Information:
Entone, Inc.
2755 Campus Drive
Suite 235
San Mateo, CA 94403
U.S.A.
Tel: 650.572.7000
www.entone.com
Table of Contents
1.1
Introduction ........................................................................................................................................................... 3
Loading Batteries ...................................................................................................................................................... 4
2.1
Controlling the Hydra ............................................................................................................................................ 5
Attach the RF Remote Control Antenna.................................................................................................................... 6
URC PLUS Registration with Hydra .......................................................................................................................... 7
URC PLUS Registration with Hydra having URC PLUS logo ................................................................................... 8
URC PLUS Registration with Hydra without URC PLUS logo................................................................................. 10
3.1
Controlling the Amulet......................................................................................................................................... 11
4.1
IR Reception Range................................................................................................................................................ 12
Controlling Your Television and other A/V Devices............................................................................................ 13
To Program a TV or AUX device............................................................................................................................. 14
Auto Search Procedures ......................................................................................................................................... 15
Appendix A – Device Code............................................................................................................................................ 16
Appendix B – Other Features ........................................................................................................................................ 23
Showing URC PLUS Firmware Version.................................................................................................................. 23
Showing Programmed Device Code....................................................................................................................... 23
Factory Reset.......................................................................................................................................................... 23
2
Copyright  2007 Entone, Inc. All rights reserved
URC PLUS User’s Guide
Chapter
1
1.1 Introduction
The Entone Universal Remote Control Plus (URC PLUS) is designed to work either on Radio Signals (RF) or InfraRed
(IR). It can control Hydra Multi-Television Gateway using RF from another room where is not at direct sight distance
from the Hydra. Or, it can use IR to control Amulet Video Receiver at direct sight distance. The URC PLUS can also be
used to control other A/V devices such as TV, DVD player and audio equipment using IR.
The URC PLUS differs from the old URC on the followings :
3
The old URC can only support old Hydra hardware. URC PLUS supports both the old Hydra and new Hydra
hardware (with URC PLUS logo printed on the front panel).
URC PLUS supports Amulet
URC PLUS supports more A/V devices
Copyright  2007 Entone, Inc. All rights reserved.
URC PLUS User’s Guide
Loading Batteries
The URC PLUS comes with AA-size batteries, which need to be installed when you first receive your system.
When you replace old batteries, you should replace all of the batteries. Use batteries of the same kind, for
example alkaline or carbon zinc, and do not mix batteries of different kinds. Alkaline batteries last longer than
carbon zinc.
Warning: Mixing old and new batteries or different types of batteries poses a fire hazard.
To load batteries to URC PLUS:
1. Press down on the battery cover’s top latch and slide the cover off.
2. If you are changing out batteries, take out all of the old batteries.
3. Put the new batteries in. Make sure you match the plus ( “+” ) ends with the plus markings on the battery
case.
4. Slide the cover back into place.
Figure 1-1 Loading Batteries to URC PLUS
4
Copyright  2007 Entone, Inc. All rights reserved.
URC PLUS User’s Guide
Chapter
2
2.1 Controlling the Hydra
Hydra is a multi-television gateway. It can support multiple TVs in multiple rooms viewing different channels
or TV programs. You can use URC PLUS to control Hydra using radio signals (RF). These radio signals
travel over long distances and go though walls and other solid objects. You must connect the RF Remote
Control Antenna to the rear panel of the Hydra.
Your Hydra comes with 3 URC PLUS. (Additional URC PLUS can be purchased separately.) Your URC
PLUS must be registered to one of the 3 decoders before it can be used. One URC PLUS can only be
registered to one decoder. However, you can register at most 3 URC PLUS to a decoder. After registration,
you need to use the corresponding URC PLUS to control the decoders.
Figure 2-1 Controlling Hydra using RF URC PLUS
5
Copyright  2007 Entone, Inc. All rights reserved.
URC PLUS User’s Guide
Here are some principles of the remote registration method:
Each decoder allows a maximum of 3 URC PLUS to be registered and a registration list is maintained.
If the user has registered 3 URC PLUS and tries to register another URC PLUS, the first registered
URC PLUS will be removed from the registration list. This works as a first-in-first-out fashion.
Each URC PLUS can only be registered for one decoder. If user tries to register a URC PLUS which is
already registered to another decoder, that remote registration will be removed from the original
registration list.
The registration list is maintained in order. If the secondly registered URC PLUS is removed from the
list, the third entry will move forth to the second and the third will be blank for a new URC PLUS to be
registered.
You must install the RF Remote Control antenna before doing the registration. Please refer to the previous
section for installing the RF Remote Control Antenna.
Attach the RF Remote Control Antenna
You need to attach the RF Remote Control Antenna to the Hydra’s rear panel “REMOTE ANTENNA” input
in order to use the radio control remotes.
Figure 2-2 Attaching RF Remote Control Antenna
NOTE: Be sure to set the antenna straight up so that you can use the URC PLUS from as far away as
possible. Don’t let the antenna touch anything.
ATTENTION: If your URC PLUS isn’t working very well from far away, you may be experiencing
interference from objects near your receiver. To improve your URC PLUS’s reception range, try any or all of
the followings:
1. Place the receiver higher than all of the other equipment in your entertainment center.
2. Provide room above the receiver so that the antenna can be installed straight up. If this is not possible,
tilt the RF Antenna at about a 30° angle.
3. Place the RF antenna outside the entertainment center by using a coaxial cable to connect the antenna
to the Hydra.
4. Try moving the Hydra to other locations.
6
Copyright  2007 Entone, Inc. All rights reserved.
URC PLUS User’s Guide
URC PLUS Registration with Hydra
There are 2 types of Hydra boxes, the new one with the URC PLUS logo on top of the front panel and the
old one without the URC PLUS logo. The registration method for the new box and the old box is different.
Figure 2-3 URC PLUS Logo
Figure 2-4 New Hydra with URC PLUS logo
The following table lists the new and old Hydra box type :
New Hydra with URC PLUS logo
Old Hydra without URC PLUS logo
Hydra HD B Series, Amulet HD
Hydra II, Hydra HD A Series
Check your Hydra box type and use the corresponding registration method.
7
Copyright  2007 Entone, Inc. All rights reserved.
URC PLUS User’s Guide
URC PLUS Registration with Hydra having URC PLUS logo
1. Press and hold the “OK” button on the Hydra front panel for approx. 5 seconds. When releasing the
“OK” button, the Hydra front panel will display “RC REG”. The Hydra is now in remote registration mode.
Figure 2-5 Hydra in Remote Registration Mode
2. On the URC PLUS, press and hold the “STB” button for approx. 5 seconds. The “STB” button backlight
will illuminate.
Figure 2-6 URC PLUS in Remote Registration Mode – Step 1 (for box with URC PLUS logo)
On the URC PLUS, press “STB” once again. Both the “STB” and “AUX” button backlight will illuminate.
Figure 2-7 URC PLUS in Remote Registration Mode – Step 2 (for box with URC PLUS logo)
Figure 2-8 URC PLUS in Remote Registration Mode – Step 3 (for box with URC PLUS logo)
Now the URC PLUS is in registration mode.
8
Copyright  2007 Entone, Inc. All rights reserved.
URC PLUS User’s Guide
3. Select the decoder to register by:
Press “1” to register URC PLUS to decoder 1.
Press “2” to register URC PLUS to decoder 2.
Press “3” to register URC PLUS to decoder 3.
After you enter a registration event, the “STB” button backlight on the URC PLUS will blink twice to
indicate that the registration process was successful.
The Hydra front panel will display “RC REG Dx” to indicate that the registration process was successful.
Figure 2-9 Remote Registration Successful
Pressing a key other than “0”, “1”, “2”, “3” or a button is not pressed within 10 seconds, the “STB”
backlight will extinguish and the URC PLUS registration process will be terminated.
4. If the Hydra does not receive any URC PLUS registration event within 30 seconds, the process will be
terminated.
The Hydra front panel displays the following messages during remote control registration:
Front Panel Message
RC REG TO
RC REGERR
RC REG
RC REGEND
RC REG D1
RC REG D2
RC REG D3
Description
Registration times out
Registration error
In registration mode
Registered to IR only mode
Registered to decoder 1
Registered to decoder 2
Registered to decoder 3
Table 2-1 Remote Registration Messages
NOTE:
While the URC PLUS is in “STB” mode, the volume +/- and MUTE key signal will be sent to the TV.
While the URC PLUS is in “STB” mode, the POWER key signal will be sent to both the STB and the
programmed TV.
9
Copyright  2007 Entone, Inc. All rights reserved.
URC PLUS User’s Guide
URC PLUS Registration with Hydra without URC PLUS logo
1. Press and hold the OK button on the Hydra front panel for about 5 seconds. When the OK button is
released, the Hydra front panel Standby/On indicator blinks twice (alternates red and green), then stays
lit red to indicate that the Hydra is now in remote registration mode.
Figure 2-8 Hydra in Remote Registration Mode
2. On the URC PLUS, press and hold the “STB” button for approx. 5 seconds. The “STB” button backlight
will illuminate. Now the URC PLUS is in registration mode.
Figure 2-9 URC PLUS in Remote Registration Mode (for box without URC PLUS logo)
3. Select the decoder to register by:
Press “1” to register URC PLUS to decoder 1.
Press “2” to register URC PLUS to decoder 2.
Press “3” to register URC PLUS to decoder 3.
After you enter a registration event, the “STB” button backlight on the URC PLUS and the Hydra front
panel Standby/On indicator will blink twice to indicate that the registration process was successful.
Pressing a key other than “0”, “1”, “2”, “3” or a button is not pressed within 10 seconds, the “STB”
backlight will extinguish and the URC PLUS registration process will be terminated.
4. If the Hydra does not receive any URC PLUS registration event within 30 seconds, the process will be
terminated.
NOTE:
While the URC PLUS is in “STB” mode, the volume +/- and MUTE key signal will be sent to the TV.
While the URC PLUS is in “STB” mode, the POWER key signal will be sent to both the STB and the
programmed TV.
10
Copyright  2007 Entone, Inc. All rights reserved.
URC PLUS User’s Guide
Chapter
3
3.1 Controlling the Amulet
Amulet is a single television video receiver. You can connect Amulet to a primary TV only. Amulet only uses
InfraRed (IR) to receive remote control signals.
Unlike Hydra, you do not need to do remote registration in order to use URC PLUS to control Amulet.
However, you have to program the URC PLUS to use IR.
To set the URC PLUS to use IR to control Amulet:
1. On the URC PLUS, press and hold the “STB” button for approx. 5 seconds. The “STB” button backlight
will illuminate. Now the URC PLUS is in registration mode.
Figure 3-1 URC PLUS in Remote Registration Mode – Step 1 (for Amulet using IR mode)
2. On the URC PLUS, press “STB” once again. Both the “STB” and “AUX” button backlight will illuminate.
Figure 3-2 URC PLUS in Remote Registration Mode – Step 2 (for Amulet using IR mode)
Figure 3-3 URC PLUS in Remote Registration Mode – Step 3 (for Amulet using IR mode)
11
Copyright  2007 Entone, Inc. All rights reserved.
URC PLUS User’s Guide
3. Press “0” to set URC PLUS to IR mode only. The URC PLUS will not send any RF signal.
The “STB” button backlight on the URC PLUS will blink twice to indicate that the setting was successful.
Pressing a key other than “0”, “1”, “2”, “3” or a button is not pressed within 10 seconds, the “STB”
backlight will extinguish and the URC PLUS registration process will be terminated.
IR Reception Range
IR signals travel only short distances (40 feet or less), and cannot go through walls or other solid
objects. You must point the URC PLUS to the Amulet, with no objects blocking the line of sight.
Figure 3-4 IR Reception Range
12
Copyright  2007 Entone, Inc. All rights reserved.
URC PLUS User’s Guide
Chapter
4
4.1 Controlling Your Television and other A/V Devices
The URC PLUS can also be used to control TVs and other A/V devices such as DVD players and recorders.
The URC PLUS uses InfraRed (IR) light signals to control other devices that the remote is programmed to
control. IR signals travel only short distances (40 feet or less), and cannot go through walls or other solid
objects. You must point the URC PLUS directly at these devices, with no objects blocking the line of sight.
Figure 4-1 Controlling Devices using IR URC PLUS
You can program URC PLUS to control one TV and one AUX device. Use the remote control’s mode keys
(i.e., “STB”, “TV”, or “AUX”) to control a specific device. When pressed, the selected mode key will light up
confirming your choice. Then you can use the URC PLUS to control your STB, TV or AUX device.
You have to program the URC PLUS what TV and AUX devices you are using by either 1) entering the 4digit device code 2) doing an auto search.
NOTE:
While the URC PLUS is in “STB” mode, the volume +/- and MUTE key signal will be sent to the TV.
While the URC PLUS is in “STB” mode, the POWER key signal will be sent to both the STB and the
programmed TV.
13
Copyright  2007 Entone, Inc. All rights reserved.
URC PLUS User’s Guide
To Program a TV or AUX device
1. Locate the device code for your desired device in the device code table provided in the Appendix. If you
could not find the device code for your device or it does not work after trying the listed device codes for
your device brand, then you can go to the next section to try the auto search procedures.
2. Turn on your device and with media inserted (if applicable).
3. On the remote control, press a device mode key once (i.e., “TV” or “AUX”).
Figure 4-2 Select the device mode
NOTE: Use the “AUX” mode key to program control of VCR, DVD player, cable box, satellite set-topbox and audio device.
4. Press and hold the “Setup” key until the selected mode key backlight blinks twice, then release “Setup”.
The device mode key will light up.
Figure 4-3 Press SETUP for 5 seconds to enter device setup mode
5. Enter the four-digit device code for you device. If you perform this procedure correctly, the selected
device mode key backlight will blink twice.
NOTE: If you enter an invalid device code, the selected device mode key will fast blink 7 times. Device
program mode will be terminated.
6. Aim the remote control at your device and press the “Power” once. The device should be turn off. If it
does not respond, repeat the above steps.
14
Copyright  2007 Entone, Inc. All rights reserved.
URC PLUS User’s Guide
Auto Search Procedures
If your device does not respond to the remote control after trying all devices codes listed for you brand, or if
your brand is not listed at all, try searching for your device code as follows:
1. Turn on your TV or your A/V device.
2. On the remote control, press a device mode key once (i.e., TV or AUX).
NOTE: Use the AUX mode key to program control of VCR, DVD player, cable box, satellite set-top-box
and audio device.
3. Press and hold the “Setup” key until the selected device mode key blinks twice, then release “Setup”.
The device mode key will light up.
4. Press the “POWER” key once.
5. Aim the remote control at the TV. Press either the “CHANNEL UP” key or “CHANNEL DOWN” key to
do device auto-scan:
a. Press the “CHANNEL UP” key to start searching upward at an approx. 5 seconds interval for each
device code. The TV/AUX mode key will be on and blink every 5 seconds while in the device scan
mode.
NOTE: In this search mode, the remote control will send IR codes from the library starting from the
lowest code set number to the end of code set for that device; OR
b. Press the “CHANNEL DOWN” key to start searching downward at an approx. 5 seconds interval
for each code set. The TV mode key will be on and blink every 5 seconds while in the device scan
mode.
NOTE: In this search mode, the remote control will send IR codes from the highest code set number to
the beginning of code set of that device.
6. If the TV turns off, a working code has been found. Press OK once to lock in the code. The selected
mode key will blink twice
7. If all code sets of that device is exhausted in the search and the OK is not pressed, the selected device
key will fast blink 7 times and the search mode will be terminated.
NOTE: Auto-Search does not scan device codes from 4056 to 4071. For decode codes from 4056 to 4071,
you have to enter the device code manually.
15
Copyright  2007 Entone, Inc. All rights reserved.
URC PLUS User’s Guide
Appendix
Appendix A – Device Code
Your URC Plus can control many brands and models of television, VCR, DVD and other types of audio-visual equipment.
The following pages lists device codes for many categories and brands of equipment. Many brands list more than one
code, and you may need to test several codes to find the best match for your equipment. Your equipment may be
supported even if your brand is not shown in the list below. If you cannot locate your brand, or none of the listed device
codes works, then you may still use the Auto-Search feature to try to locate a suitable device code. Instructions for using
the Auto-Search feature is located on page 15 of this guide.
DVD
DVD – DVD Player
Aiwa
Apex
2026, 2131
2001, 2056, 2057, 2095,
2098
Audiovox
2132
Blaupunkt
2136
BOSE
2122, 2130
Nakamichi
2116
Emerson
2073
Nexxtech
2140
Go Video
2046, 2127, 2129
Norcent
2005, 2117
Hitachi
2126
Onkyo
2006
JVC
2047, 2097
Oritron
2009
Panasonic
2066
Panasonic
Philips
2051
Philips
2066, 2075, 2076
2018, 2032, 2045, 2051,
2091, 2109
Pioneer
2008
Samsung
2049, 2074, 2085
Polaroid
2007
Sanyo
2050
Proscan
2010, 2033, 2118
Sony
2065, 2067
Qwestar
2009
2010, 2048, 2063, 2077,
2099, 2107, 2118
Toshiba
2080, 2084
Zenith
2052, 2128
Broksonic
2053, 2072
Clarion
2100
Classic
2101
Daewoo
2058, 2062, 2137, 2138
RCA
Denon
2040, 2110, 2133
Sampo
Emerson
2059, 2073
Polaroid
2007
RCA
2048
2119
2012, 2049, 2074, 2085,
2102
DVD – Home Theater
Fisher
2112, 2134
Samsung
GE
2041, 2079, 2118
Sansui
2071
BOSE
2130
Go Video
2046, 2127, 2129
Sanyo
2050, 2120
JBL
2043
2114
Sharp
2013, 2015, 2044, 2086
Koss
2060
Sherwood
2121
2014, 2020, 2022, 2065,
2067, 2068, 2069, 2070,
2087, 2103, 2108, 2113
Onkyo
2024
Sylvania
2064, 2078, 2092
RCA
2042
Techwood
Sony
2108, 2113
Venturer
2011
GPX
Harman
Kardon
2125
Hitachi
2000, 2027, 2126
Irradio
JVC
2017
2047, 2090, 2096, 2097,
2115
Kenwood
2019, 2039
Konka
2029
Toshiba
2141
2023, 2025, 2037, 2038,
2054, 2080, 2084, 2088,
2093, 2094
Lasonic
2081
Yamaha
2028
Magnavox
2002, 2018
Zenith
2052, 2128
Marantz
2034
Memorex
2003
Mintek
2004
Mitsubishi
2021, 2030, 2123
Broksonic
2072
2059, 2139
Daewoo
2062
NAD
16
Sony
Philips
2036
Pioneer
2016
DVD - Network DVD
Go Video
DVD - DVD/VCR Combo
2124
DVD - Portable DVD
CyberHome
2083
Copyright  2007 Entone, Inc. All rights reserved.
URC PLUS User’s Guide
RCA
2055
Viewsonic
0149
Toshiba
2135
Gateway
0038
DVD - TV/DVD Combo
TV - Plasma TV Monitor
Apex
2095
Acer
0041
Broksonic
2053
Fujitsu
0029
RCA
2063, 2099
Pioneer
0035
Sansui
2071
Sylvania
2092
Toshiba
2054
DVD - TV/DVD/VCR Combo
Panasonic
RCA
2075, 2076
2077
Sharp
2086
Sylvania
2064, 2078
Toshiba
2093, 2094
TV
TV - Digital TV
Zenith
0020
TV - HDTV
TV - Projection TV
Hitachi
0132
JVC
0130, 0131
Panasonic
0010
Sony
0128
Toshiba
0127
TV - TV
Abex
0098
Admiral
0001, 0099
Adventura
0100
Aiko
0015
Aiwa
0034
Akai
0002
Alleron
0044
Amtron
0036
Apex
0088
Anam National 0003, 0036
Daewoo
0135
AOC
Hitachi
0134
Apex
0074, 0111, 0119
Philips
0037
Audiovox
0036
RCA
0143
Bell & Howell
0001, 0045
Sony
0137
Benq
0042
Bradford
0036
Broksonic
0114, 0121
Candle
0004, 0007, 0100
Celebrity
TV - HDTV Projection TV
Sony
0037
TV - LCD TV
Benq
0136
ESA
0046
NET-TV
0040
Sharp
0138
Sylvania
0046
TV - PLASMA TV
17
0004, 0005
0016, 0097, 0106
Daytron
0004, 0097
Dell
0141, 0142, 0146
Dimensia
0000
Electroband
0002
Electrohome
0002, 0003, 0004, 0018,
0021
Emerson
0004, 0011, 0013, 0025,
0031, 0033, 0036, 0044,
0045, 0080, 0097, 0102,
0107
Envision
0004
Fisher
0043, 0045, 0047, 0103
Fujitsu
0044
Funai
0036, 0044
Futuretech
0036
GE
0000, 0003, 0004, 0008,
0021, 0048, 0049, 0063,
0068, 0070, 0144
Goldstar
0004, 0005, 0011, 0018,
0050, 0090, 0091, 0097,
0098
Grunpy
0036, 0044
Hallmark
0004
Harvard
0036
Hisense
0112
Hitachi
0004, 0011, 0012, 0030,
0051, 0084, 0085, 0086,
0102, 0133
IMA
0036
Infinity
0053
Janeil
0100
JBL
0053
JC Penney
0000, 0004, 0005, 0007,
0012, 0021, 0048, 0049,
0058, 0063, 0068, 0072,
0073, 0075, 0097, 0098
JCB
0002
Jensen
0004
0002
JVC
0011, 0012, 0026, 0049,
0054, 0055, 0080, 0117
Kawasho
0002, 0004
Citizen
0004, 0007, 0015, 0036,
0073, 0097
Kenwood
0004, 0018
Colortyme
0004
Concerto
Contec/Cony
0004
Kloss
Novabeam
0036, 0056, 0057, 0100
0011, 0012, 0036
KTV
0036, 0097
Craig
0036
LG
0005
Crown
0036, 0053
Loewe
0053
Logik
0001
Curtis Mathes
0000, 0004, 0014, 0045,
0073, 0097
CXC
0036
Daewoo
0004, 0005, 0013, 0015,
Luxman
0004
LXI
0000, 0004, 0045, 0053,
0058, 0068, 0075
Copyright  2007 Entone, Inc. All rights reserved.
URC PLUS User’s Guide
Magnavox
0004, 0007, 0018, 0053,
0056, 0057, 0059, 0060,
0110, 0147
Majestic
0001
Marantz
0004, 0051, 0053
Megatron
0004, 0051
Memorex
0001, 0004, 0005, 0022,
0045
MGA
0004, 0005, 0018, 0021,
0047, 0061
Midland
0049, 0068, 0097, 0098
Minutz
0048
Mitsubishi
0004, 0005, 0018, 0021,
0032, 0047, 0061
0018, 0031, 0044, 0048,
0053, 0056, 0057, 0059,
0060, 0063, 0064
RCA
0000, 0003, 0004, 0005,
0008, 0018, 0028, 0052,
0065, 0067, 0068, 0071,
0076, 0082, 0102, 0104,
0106, 0108, 0115, 0151
White
Westinghouse
0013
Realistic
0000, 0045
Yamaha
0004, 0005, 0018
Zenith
0001, 0081, 0089, 0118,
0125
Sampo
0004, 0097, 0098, 0120
Samsung
0004, 0005, 0011, 0014,
0018, 0019, 0072, 0073,
0078, 0094, 0097, 0098
Sansui
0023, 0107, 0122
Sanyo
0045, 0103
Apex
0074
Scotch
0004
Broksonic
0114
RCA
0076, 0115
Scott
0004, 0011, 0033, 0036,
0044
0122
Sylvania
0150
Sears
0000, 0004, 0012, 0018,
0044, 0045, 0047, 0055,
0058, 0068, 0075, 0103,
0105
Sansui
Toshiba
0116
TV - TV/DVD/VCR Combo
TV - TV/DVD Combo
Montgomery
Ward
0001
Motorola
0003, 0099
MTC
0004, 0005, 0073
Multitech
0036
NAD
0004, 0058, 0075, 0085
Sharp
0004, 0009, 0011, 0025,
0064, 0077, 0092, 0097,
0099, 0153
NEC
0003, 0004, 0005
Signature
0001
Panasonic
0123, 0152
0151
Nikko
NTC
0004, 0015
Simpson
0007
RCA
0015
Sony
0002, 0109
Sharp
0153
0027, 0124
0087, 0101
Onwa
0036
Soundesign
0004, 0007, 0036, 0044
Sylvania
Optimus
0085
Squareview
0105
Toshiba
Optonica
0064, 0099
SSS
0036
Orion
0023, 0033, 0107
Starlite
0036
0003, 0049, 0053, 0096,
0123, 0140, 0152
Supre-Macy
0100
Panasonic
Broksonic
0121
Supreme
0002
GE
0070
0062, 0069
Sylvania
0004, 0007, 0018, 0027,
0053, 0056, 0057, 0059,
0060, 0124, 0145, 0150
Quasar
Philco
0003, 0004, 0005, 0007,
0011, 0018, 0053, 0056,
0057, 0059
RCA
0028, 0052
Symphonic
0024, 0031, 0036, 0105
Samsung
0078
Philips
0003, 0007, 0011, 0017,
0018, 0053, 0056, 0057,
0059, 0063, 0095, 0126,
0129, 0148
Tandy
0099
Sylvania
0145
Tatung
0003
Toshiba
0006
Zenith
0118
Philips
Magnavox
0148
Technics
0049
Pilot
0097
Techwood
0004, 0049
Pioneer
0004, 0085, 0102
Portland
0004, 0005, 0015, 0097
Price Club
0073
Teknika
0001, 0004, 0005, 0007,
0011, 0012, 0015, 0036,
0044, 0060, 0073, 0096,
0097
Prima
0113
TMK
0004
TV - TV/VCR Combo
VCR
VCR – CD
Denon
1104
Prism
0049
Proscan
0000, 0008, 0068
Toshiba
0006, 0045, 0058, 0073,
0075, 0079, 0083, 0087,
0093, 0101, 0116
Proton
0004, 0011
Totevision
0097
Pioneer
1101
Universal
0048, 0063
Quasar
0003, 0039, 0049, 0062,
0069
RCA
1102, 1106
Victor
0055
Radio Shack
0000, 0045
Sony
1105
Vidtech
0004, 0005
Yamaha
1103
Viking
0100
Wards
0000, 0001, 0004, 0005,
Radio
0004, 0011, 0036, 0045,
Shack/Realistic 0064, 0097, 0098
18
JVC
1099
Onkyo
1100
Copyright  2007 Entone, Inc. All rights reserved.
URC PLUS User’s Guide
VCR - Digital Network
Recorder
Sony
1001
VCR - DVD/VCR Combo
Broksonic
1085
Emerson
1076
Hitachi
JVC
Panasonic
1043, 1045, 1092
1038
1030, 1093
1082
Philips
1091
Polaroid
1041
RCA
Samsung
1067, 1068
Garrard
1047
RCA
1065, 1066
GE
1026, 1035, 1042, 1069
Samsung
1070
Go Video
1043, 1045, 1088, 1092
Sylvania
1064
Goldstar
1031, 1036, 1040
Toshiba
1063
Gradiente
1047
Zenith
1060
Harley
Davidson
1047
1078
Daewoo
Go Video
Quasar
1094
1054, 1075, 1095
Harman Kardon 1031
VCR - VCR
Harwood
1061
Admiral
1027
Headquarter
1033
Adventura
1047
Hi-Q
1044
Aiko
1048
Hitachi
1038, 1058, 1081
Aiwa
1047
Instant Replay
1042
Akai
1081, 1084
JC Penney
1031, 1032, 1033, 1034,
1035, 1036, 1042, 1058,
1061, 1062
JCL
1042
American High 1042
Asha
Audio
Dynamics
1035
1031, 1032
Jensen
1058, 1081
JVC
1030, 1031, 1032, 1033,
1040, 1081, 1093
Sanyo
1096
Audiovox
1036
Sony
1051, 1074
Beaumark
1034, 1035
Toshiba
1052, 1053
Bell & Howell
1033
Kenwood
1031, 1032, 1033, 1040,
1081
Zenith
1029, 1089
Broksonic
1034, 1078, 1098
KLH
1061
Calix
1036
Kodak
1036, 1042
1036
Candle
1035, 1036, 1037, 1039,
1040
LG
Lloyd's
1047
Logik
1061
LXI
1036
Magnavox
1042, 1062, 1077
VCR - DVR
DIRECTV
1000
Canon
1042
Panasonic
1004
Carver
1062
Philips
1002
CCE
1048, 1061
1035, 1036, 1037, 1039,
1040, 1048
RCA
1000
RePlay
1003
Citizen
Tivo
1000
Colortyme
1031
Colt
1061
Craig
1035, 1036, 1044, 1061
Curtis Mathes
1026, 1031, 1035, 1040,
1042
Cybernex
1035
Daewoo
VCR - PVR
Tivo
1087
VCR - TV/DVD/VCR Combo
Panasonic
1072, 1073
RCA
1046
Sharp
1055
Sylvania
1050, 1071
Toshiba
1056, 1059
VCR - TV/VCR Combo
Broksonic
GE
19
1098
1069
Magnin
1036
Marantz
1031, 1032, 1033, 1040,
1042, 1062
Marta
1036
Matsushita
1042
MEI
1042
Memorex
1027, 1033, 1035, 1036,
1042, 1044, 1047, 1077
1037, 1039, 1047, 1048,
1085
MGA
1049
DBX
1031, 1032
MGN
Technology
1035
Dimensia
1026
Midland
1057
Dynatech
1047
Minolta
1058
Electrohome
1036, 1049
Mitsubishi
1049, 1058
Electrophonic
1036
1027
Emerson
1034, 1036, 1037, 1042,
1047, 1049, 1076, 1097
Montgomery
Ward
Fisher
1033, 1044
Fuji
1042, 1084
Funai
1028, 1047
Motorola
1027, 1042
MTC
1035
Multitech
1035, 1047, 1057, 1061
NEC
1031, 1032, 1033, 1040,
Copyright  2007 Entone, Inc. All rights reserved.
URC PLUS User’s Guide
1081
Nikko
STS
1042
GE
3000, 3001
Gemini
3016, 3017
Sylvania
1042, 1047, 1050, 1062,
1064, 1071
General
Instrument
3051
1036
Noblex
1035
Olympus
1042
Optimus
1027, 1036
Panasonic
1042, 1072, 1073, 1079,
1080, 1082, 1083
Pentax
1058
Pentex
Research
1040
Philco
1042, 1062
Symphonic
1028, 1047
Tandy
1033
Tashiko
1036
General
Instruments
3001, 3048
3018, 3019, 3020, 3026,
3033, 3039, 3047
Tatung
1081
Hamlin
Teac
1047, 1081
Hitachi
3001
Technics
1042, 1079
Teknika
1036, 1042, 1047
Jerrold
3001, 3016, 3021, 3022,
3046, 3048
TMK
1035
Magnavox
3023
1037, 1052, 1053, 1056,
1058, 1059, 1063
Memorex
3024
Motorola
3052, 3053, 3054
Philips
1042, 1062, 1091
Pilot
1036
Toshiba
Pioneer
1032, 1058
Totevision
1035, 1036
Movie Time
3025
Polaroid
1041
Unitech
1035
NEC
3003
Portland
1039
3025
1026
1031, 1032, 1037
NSC
Proscan
Vector
Research
Victor
1032
Oak
3014, 3027
Protec
1061
Pulsar
1077
Quarter
1033
Quartz
1033
Quasar
Radio Shack
Video Concepts 1031, 1032, 1037
Videosonic
1035
1042, 1067, 1068
Wards
1027, 1035, 1036, 1037,
1042, 1044, 1047, 1049,
1058, 1061
1027, 1036
White
Westinghouse
1028
XR-1000
1042, 1047, 1061
Yamaha
1031, 1032, 1033, 1040,
1081
Zenith
1029, 1060, 1077, 1084,
1089, 1090
Radio
1033, 1035, 1036, 1042,
Shack/Realistic 1044, 1047, 1049
Radix
1036
Randex
1036
RCA
1026, 1035, 1042, 1046,
1058, 1065, 1066, 1086,
1094
Realistic
1027, 1033, 1035, 1036,
1037, 1042, 1044, 1047,
1049
Ricoh
1090
Runco
1077
Samsung
1035, 1037, 1054, 1057,
1070, 1075, 1095
Sanky
1027, 1077
Cable Box
Cable Box - Cable Box
Panasonic
3042, 3045
Philips
3009, 3010, 3011, 3013,
3017, 3023, 3028, 3029,
3030
Pioneer
3031, 3032
Proscan
3000, 3001
RCA
3005, 3041, 3043, 3045,
3048
Realistic
3007
Regal
3020, 3033, 3047
Regency
3015
Rembrandt
3001
Samsung
3032
Scientific
Atlanta
3004, 3034, 3035, 3036,
3049
Signal
3016
Signature
3001
ABC
3000, 3001, 3002, 3004,
3046
Sony
3050
Adelphia
3049
Sprucer
3045
Antronix
3006, 3007
Archer
3007, 3008
Standard
Component
3037, 3038
Cable Vision
3050
Starcom
3016, 3046
Cabletenna
3006
Stargate
3016
3005
Starquest
3016
Sansui
1032, 1081
Sanyo
1033, 1035, 1044, 1096
Scott
1034, 1037
Cableview
Sears
1033, 1036, 1042, 1044,
1058
Colour Voice
3010, 3011
TIME WARNER 3055
Sharp
1027, 1039, 1049, 1055
Comcast
3051, 3052
Tocom
3002, 3021
3016
Shintom
1061, 1084
Comtronics
3012
Tusa
Shogun
1035
Contec
3014
TV86
3025
3006, 3007
Signature
1027
COX
3053
Unika
Singer
1042, 1061, 1090
Eastern
3015
United Cable
3046
Universal
3006, 3007, 3008
Sony
20
1051, 1074, 1084
GC Electronics 3007
Copyright  2007 Entone, Inc. All rights reserved.
URC PLUS User’s Guide
View Star
3014, 3023, 3025
Zenith
3044
Satellite
Satellite - HDTV Tuner
Panasonic
4054
Satellite - SAT-DVR
DIRECTV
4058, 4059, 4060, 4062,
4063
Proscan
4001, 4016, 4033, 4034,
4065
Quasar
5035
5059
Sharp
5063, 5064, 5065, 5066
RCA
4001, 4016, 4024, 4033,
4034, 4040, 4055, 4065,
4070
RCA
Sherwood
5045
Realistic
4009
Samsung
4044, 4046
Sony
Sony
5054
Teac
5053
4017, 4035, 4037, 4038,
4042, 4071
Technic
5035
4032
Technics
5035
STS1
4010
Toshiba
5061
STS3
4012
Victor
5058
4013
Yamaha
5041
STS
DISH Network
4061
STS4
Hughes
4058
Toshiba
4014, 4018, 4050
Philips
4058, 4063
Uniden
4015, 4029
RCA
4058, 4059
Zenith
4051
Samsung
4058
Sony
4060, 4062
SAT - Satellite
Receiver/Recorder
Tivo
4058, 4060, 4063
Audio – Home Theater
Zenith
4064
Philips
4048
BOSE
5071
RCA
4041
JBL
5072
Sony
4047
Koss
5074
Onkyo
5075
Satellite – Satellite Receiver
Alphastar
4023
Chaparral
4002, 4003
DIRECTV
4035, 4036, 4038, 4039,
4043, 4044, 4045, 4049,
4050, 4051, 4052, 4056,
4058, 4069, 4070, 4071
Audio
Audio - Amplifier
DISH Network
4000, 4066, 4067, 4068
Aiwa
5037, 5054
Dishnet
4022
Carver
5036
Drake
4004, 4005
Citizen
5060
Echostar
4030
Denon
5048
GE
4001, 4016, 4033, 4034,
4056, 4065
Fisher
5036
General
Instruments
GE
5062
4006, 4007, 4008
Goldstar
5050, 5055
Hitachi
4026, 4027
Harmon/Kardon 5047
Hughes
4036, 4069
Hitachi
5068
JVC
5052, 5058
Kenwood
5049, 5056
Magnavox
5069
Marantz
5034
Nakamichi
5046
NEC
5067
Onkyo
5039, 5040, 5051
Optimus
5042
Panasonic
5035
Hughes
Network
4069
Hughes
Network
Systems
4031, 4069
Humax
4071
JVC
4025
Mitsubishi
4043, 4045
Panasonic
4019, 4049, 4052
Philips
4028, 4039, 4057
Pioneer
4053
Primestar
4020
21
Pioneer
5043, 5044, 5057, 5070
Proton
5069
Audio - DVR
RePlay
5062
Philips
5077
Pioneer
5078
RCA
5079
Sony
5080, 5081
Venturer
5082
Audio - Receiver/Tuner
Aiwa
5000, 5001, 5002, 5004,
5005, 5006
BOSE
5007, 5071
Carver
5000
Denon
5008
Harman Kardon 5000, 5009
JBL
5009
JVC
5010
Kenwood
5011, 5012
Linn
5000
Maganvox
5000
Marantz
5000
Onkyo
5018
Philips
5000
Pioneer
5021, 5022
RCA
5024, 5025, 5026
Copyright  2007 Entone, Inc. All rights reserved.
URC PLUS User’s Guide
Sansui
5000
Sherwood
5027
Sony
5017, 5028, 5029, 5030,
5031, 5032, 5033, 5080,
5081
Technics
5016
Wards
5000, 5021
Yamaha
5003, 5014, 5015, 5021
22
Audio - Tuner/CD Combo
BOSE
5007
Copyright  2007 Entone, Inc. All rights reserved.
URC PLUS User’s Guide
Appendix B – Other Features
Showing URC PLUS Firmware Version
The URC PLUS firmware version is in the format of x.y.z, where x, y and z is digit 0-9. Use the following
procedures to show the URC PLUS firmware version:
1.
2.
3.
4.
5.
Press “STB”.
Press and hold “SETUP” for 5 seconds.
The “STB” backlight will illuminate.
Press “INFO” once.
The 3 digits of the firmware version (x, y and z as described above) will be displayed in the following
manner.
a. The “STB” backlight blinks to indicate the digit. One blink indicates 1, 2 blinks indicates 2, etc
until 9 blinks indicates 9. A 0 is indicates by a shot, long, short, long, short, long blink.
b. In between each digit, the “STB” backlight will be off for 1 second.
c. For example, the following blink pattern shows a firmware version of 2.0.4.
..
.-.-.-
....
Showing Programmed Device Code
You can display the 4-digit device code by the following procedures:
1.
2.
3.
4.
5.
Press “TV” to display the TV device code or “AUX” to display the AUX device code.
Press and hold “SETUP” for 5 seconds.
The “TV” or “AUX” backlight will illuminate.
Press “INFO” once.
The 4-digits device code will be displayed in the following manner.
a. The “TV”/”AUX” backlight blinks to indicate the digit. One blink indicates 1, 2 blinks indicates 2,
etc until 9 blinks indicates 9. A 0 is indicates by a shot, long, short, long, short, long blink.
b. In between each digit, the “TV”/”AUX” backlight will be off for 1 second.
c. For example, the following blink pattern shows a device code of 0123.
.-.-.-
.
..
...
Factory Reset
You can factory reset the remote by pressing the “SETUP” and “POWER” button at the same time for 10
seconds. After factory reset, the programmed device setting will lose. You need to program the devices and
do the remote registration with your Hydra/Amulet again. In case, you find your remote does not function as
expected, you can also try the factory reset.
23
Copyright  2007 Entone, Inc. All rights reserved.
">