Catalogue Sheet: C8ES300 & C8SE300 Series

Catalogue Sheet: C8ES300 & C8SE300 Series
C8ES300 & C8SE300
Series
Bilingual Extruded Aluminum Sign
• Universal, field-selectable chevrons (knockout)
• E nergy efficient – consumes less than 7W in AC or DC mode
• Normal AC and emergency DC operation
120, 277 or 347V AC input; 6 to 24V DC input
• Available in single or double face
• Custom wording available on request
• Indirect refractive technology provides bright, even illumination
• Long-life ALINGAP technology, energy-efficient LED light
source
• CSA certified, meets or exceeds CSA 22.2 No. 141 requirements
Prepared by:
The Exit Sign in a Self-Powered configuration shall be equipped
with a Nickel-Cadmium battery and shall stay illuminated during
emergency operation for at least two hours upon AC failure.
POwer consumption
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141
AC Specs
The equipment shall be Emergi-Lite® Model:
DC Specs
AC/DC standard,
red
120/347VAC
Less
than 2W
6 to 48VDC
Less
than 3W
AC/ special DC,
red
120/277/347VAC
Less
than 2W
36 or 48 or
120VDC
Less
than 6W
120VAC
Less
than 6W
120VDC
Less
than 6W
120 or 347VAC
Less
than 7W
Nickel-Cadmium
battery
Min. 2
hours
Self-Powered,
red
Date:
Supply and install the Emergi-Lite® C8ES300 Series LED Exit Sign.
The equipment shall operate with universal AC input voltage of
120, 277 or 347VAC at less than 1.5W and universal two-wire DC
input voltage from 6VDC to 24VDC at less than 2.5W for single and
double face signs. The Exit Sign shall consist of a two-piece white
extruded aluminum combined body/faceplate with a maximum
depth of 1 1/4”. The exit shall also include extruded aluminum
end caps with white gaskets in order to provide protection to the
internal components and eliminate any possible light leaks. The
exit fixture shall be either single or double-faced as shown on the
drawings. The faceplate shall be of a stencil design and will have
6” high letters with a 3/4” stroke indicating both EXIT and SORTIE
side by side. The canopy shall fasten to the exit body for ease of
installation in either ceiling or wall mount. The fixture shall contain
a light source, which shall be LED with a long life and shall consist
of separate AC and DC LED sources in the case of AC/DC-remote
equipment. Red LED technology shall be ALINGAP.
• P re-specified mounting
120VAC/DC two
wires, red
Contractor:
Typical specifications
Features
• Thin profile, 2-piece extruded aluminum housing simply slides
together
Model
Project/Location:
.
Wire guards
460.0059-E
Wall Mount
460.0092-E
Ceiling Mount
Dimensions
Dimensions are approximate and subject to change.
55/8” [14.2 cm]
55/8” [14.2 cm]
303/8” [77.1 cm]
95/8” [24.3 cm]
87/8” [22.5 cm]
47/8” [12.5 cm]
13/8” [3.4 cm]
303/8” [77.1 cm]
ordering information
Series
Faces
C8ES30= exit sortie
C8SE30= sortie exit
2= single face
3= double face
colour
W= polar white
B= black
TA= textured
aluminum
BA= brushed
aluminum
mounting
-CM= ceiling mount
-WM= wall mount
EXEMPLE: C8ES302W-CM-UTP
32
voltage
-U= 120/277/347VAC, 6 to 24Vdc
-U36= 120/277/347Vac-36Vdc
-U48= 120/277/347/Vac-48Vdc
-U120= 120/277/347/VAC-120Vdc
-I= 120Vac, Self-Powered
-3I= 347Vac, Self-Powered
-EM120-2W= 120Vac-120Vdc-2
wires
options
-TP= tamper-proof screws
990.0119-E= tamper-proof bit*
*One bit needed per order.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement