Bulldog Security 500 User manual
Add to my manuals27 Pages
Bulldog Security DELUXE 500 is a versatile car security and remote control system that provides a range of features for enhanced vehicle protection and convenience. With its two-way LCD remote control transceiver, you can remotely arm/disarm the alarm, monitor the vehicle's status, and even start the engine. The system also offers passive arming, panic mode, car finder, valet mode, and multiple timer outputs for controlling various vehicle functions.
advertisement
. .
. .
WARRANTY
Bulldog Warranty Information
All Bulldog models have a Limited Lifetime Warranty on the main control module.
All parts excluding the control module have a two year warranty against defects in workmanship, This includes shock sensors, remote transmitters and sirens. The control module will be repaired or replaced at our discretion for up to a 12 month period at no charge. After 12 months a $30.00 fee will be charged for repair or replacement of the control module.
Removal and reinstallation charges are not the responsibility of JBS Technologies, LLC the manufacturer of Bulldog Security.
Warranty registration must be completed within 14 days of the original date of purchase. Registration can be mailed in or performed on line at www.bulldogsecurity.com. JBS
Technologies makes no warranty against the theft of a vehicle or its contents. This warranty only extends to the original system purchaser in the vehicle it was originally installed in.
Limitation of Remedies
The purchasers remedy is limited to the repair or replacement of the unit and in no event shall exceed the purchase price.
Incidental, consequential and or indirect damages are expressly disclaimed. No person or entity is authorized to alter or amend this limited lifetime warranty.
2
. .
TABLE OF CONTENTS
Important Notice...................................................................4
A. REMOTE TRANSMITTER OPERATION.....................................5
B. TWO-WAY TRANSEIVER REMOTE CONTROL OPERATION .........6
C. LED DISPLAY CHART..........................................................6
D. CHIRP INDICATOR.............................................................6
E. PARKING LIGHT INDICATOR DISPLAY...................................6
F. ALARM OPERATING CONDITION ..........................................7
G. ACTIVE ARMING................................................................7
H. SILENT ARMING / DISARMING ............................................8
I. PASSIVE STARTER DISABLE................................................8
J. PASSIVE ARMING ..............................................................8
K. ACTIVE DISARMING...........................................................9
L. DISARMING WITHOUT A TRANSMITTER................................9
M. VALET MODE................................................................9-10
N. CAR FINDER ...................................................................10
O. PANIC MODE...................................................................11
P. SYSTEM STATUS CHECK ...................................................11
Q. DOME LIGHT SUPERVISION ..............................................11
R. IGNITION CONTROLLED DOOR LOCKS................................11
S. TRUNK RELEASE..............................................................12
T. CHANNEL 4 TIMER OUTPUT...............................................12
U. CHANNEL 5 TIMER OUTPUT...............................................12
V. CHANNEL 6 TIMER OUTPUT ..........................................12-13
A. TO REMOTE START THE VEHICLE .......................................14
B. ENGINE START MEMORIZING FOR MANUAL TRANSMISIONS..15
C. OPERATING THE VEHICLE WHILE IN REMOTE START MODE...15
D. PIT STOP FEATURE ..........................................................16
E. TURBO MODE..................................................................16
F. TIMER/TEMPERATURE START........................................16-18
G. INTERIOR TEMPERATURE MONITOR ...................................18
H. HOW TO TURN OFF THE REMOTE STARTER..........................18
I. SHUT-DOWN INPUTS .......................................................19
J . DISABLING THE REMOTE STARTER ....................................19
K. BATTERY REPLACEMENT ...................................................20
L. REMOTE ICON DESCRIPTION CHART ...........................20-21
M. PROGRAMMING THE REMOTE TRANSMITTER ................21-26
D500OM 6/04
3
. .
IMPORTANT NOTICE
WARNINGS:
As with any product that performs automatic functions, there are certain safety precautions that you must practice and be aware of.
1. Keep all transmitters out of the reach of children
2. Do not leave anyone in the vehicle while running in remote control mode.
3. Notify servicing personnel that the vehicle can be remote started.
4. Do not start the vehicle by remote while the vehicle is in an enclosed area or garage.
5. Always apply the parking brake and lock the vehicle before exiting.
6. The use and operations of this system is the sole responsibility of the operator.
7. Some areas may have local ordinances that prohibit leaving a vehicle running on public streets.
4
. .
OPERATION
A. REMOTE TRANSMITTER OPERATION:
Transmitter
Button System Function or Feature
Lock Doors & Arm the Security System
(3 sec.)
Car Locator
Panic function
Remark
Works when armed only
Press and hold for 3 sec.
+ Silent Arming / Disarming
Unlock Doors & Disarm System
Ign. in the "Off" position.
- Two Steps Door Unlock & Disarm System Press twice within 3 sec.
(2 sec.) Trunk Release (Channel 3)
- Passive Arming By-pass
- - Remote Control Entry/Exit Valet Mode
Press and hold for 2 sec.
While system is disarmed.
While system is disarmed,
Press within 3 seconds
Press twice within 3 sec.
- Activate or Turn Off The Remote Start
+
+
Channel # 4 Timer Output
Channel # 5 Timer Output
+ Channel # 6 Timer Output
Switching code for 2nd Car Operation For regular remote trans.
5
. .
OPERATION
B. TWO-WAY LCD REMOTE CONTROL TRANSCEIVER OPERATION:
Transceiver
Button System Function Remark
SET- SET- (C)Systems Status Check
SET- ( ) Monitor Indoor Temperature
Press within 3 sec.
Press within 3 sec.
SET- ( ) Daily Timer Start Press within 3 sec.
SET (1 sec.)LCD screen lamp turns on for 5 seconds. Press and hold for 1 sec.
SET-SET- SET Clear the Flash Icon and Melody Sound Press within 3 sec. on the LCD Screen Transmitter
SET- + Switching code for 2nd/1st Car Operation Press within 3 sec.
(2 sec.)
C. LED Status Display Chart: D. Chirp Indicators
LED Function Chirp Function
Off Disarmed
Slow Flash Armed
Fast Flash Passive Arming
On (solid)Valet Mode
1 chirp
2 chirps
3 chirps
6 chirps
Arm
Disarm
Ajar Warning
Car Locator
E. Parking Light Indicator Display Chart:
1 Flash Arm
2 Flashes Disarm
12 Flashes Car Locator
Constant On Under Remote Start Operation
6
. .
OPERATION
F. ALARM OPERATING CONDITION:
Horn/
Siren
Parking
Light
1. Arming 1 or 3 Chirps 1 Flash
2. Disarming 2 or 4 Chirps 2 or 3 Flashes
3. Trigger
4. Passive
Starter
Disable
Alarming Flashes
5. Panic Alarming Flashes
6. Car-jacking Alarming Flashes
7. Car Locator 6 Chirps 12 Flashes
LED Doors Starter Dome Light
Slow Flash Locking Disable
Slow Flash
Fast Flash
Unlocking Turns on for 30 sec.
Disable Flashes
Disable
Locking
Flashes
Disable Flashes
G. ACTIVE ARMING LOCK & ARM:
1. Press the button on the transmitter.
2. The siren will chirp once and parking lights will flash once and remain
ON for 10 seconds indicating that the system is now armed. The vehicles doors will lock upon arming when interfaced with the security systems keyless entry.
System Arm Door Ajar Clear The Flash Icon:
Press the SET button 3 times within
3 seconds will clear the flash icon on the LCD screen transceiver.
7
. .
OPERATION
H. SILENT ARMING / DISARMING: Pressing the transmitters and buttons at the same time will arm or disarm your security system, No chirping sound will be heard, arm / disarm confirmation will be through the vehicles parking lights only.
I. PASSIVE STARTER DISABLE:
The purpose of this feature is to protect the vehicle from being stolen at all times, regardless of whether or not the alarm is armed.
The vehicles starter will be disable 60 seconds after the ignition is turned off. Once the key is turned off, the LED will flash fast for 60 seconds.
After the 60-second timer has elapsed, the LED will flash slowly (one-half its normal armed rate) to indicate the passive starter disable is activated and the system will not respond to any trigger input except the ignition trigger.
J. PASSIVE ARMING
Active arming / disarming is controlled by your security systems remote transmitter. The security system is equipped with an optional Passive
Arming feature, which allows the security system to arm 30 seconds after the last door is closed. Operation is as follows.
1. Turn the ignition key to the OFF position and exit the vehicle.
2. After all doors are closed, the security systems LED will flash fast for 30 seconds. If you re-open any door, hood or truck, the security systems
LED will stop flashing. It will begin flashing again once these are closed.
3. After the 30-second timer has elapsed, the security system will automatically
ARM. The siren will chirp [1] time and the parking lights will flash [1] time and then remain ON for 10 seconds.
PASSIVE ARMING WITH PASSIVE DOOR LOCKING:
The vehicles doors will automatically lock after the passive arming cycle has been completed.
PASSIVE ARMING BY-PASS: While the system disarmed, Press the button twice, the security system will respond with [1] chirp and LED will turn ON. The security system will remain in this temporary state for as long as you wish. To exit passive by-pass, press the transmitters or buttons and the system will return to normal status.
8
. .
OPERATION
K. ACTIVE DISARMING UNLOCK & DISARM:
1. Press the button on the transmitter.
2. The siren will chirp (2) times and parking lights will
flash (2) times and then remain ON for 30 seconds indicating that the security system is now disarmed. The vehicles doors will unlock and dome light will turn ON for 30 seconds upon disarming when interfaced with the security system.
System
Disarm
TWO STEPS DOOR UNLOCK: This feature will independently unlock the drivers door only when disarming the security system. Pressing the
button a second time within 3 seconds will unlock the remaining doors.
AUTOMATIC RE-ARM: If this feature is selected, the security system will automatically re-arm itself in 60 seconds after disarming with the remote transmitter. Automatic rearm will cancel if any door is opened before the
60 second timer has elapsed.
L. DISARMING WITHOUT A TRANSMITTER
OVERRIDES THE ALARM WITHOUT PASSWORD PIN CODE:
The override function may be used if the remote transmitter is lost or inoperative.
1. Enter the vehicle and turn the ignition switch to ON position. (Alarm will sound.)
2. Within 10 seconds press and release the valet switch,
The alarm will stop sounding and enter the disarm mode. You can now start and operate the vehicle normally with the ignition key.
M. VALET MODE:
The valet switch allows you to temporarily bypass all alarm functions, eliminating the need to hand your transmitter to parking attendants or garage mechanics. When the system is in Valet Mode, all alarm function and remote starter functions are bypassed, however the remote panic
feature and remote door locks will remain operational. To use the Valet
Mode, the system must first be disarmed either by using your remote transmitter, or by operating the Manual override sequence.
9
. .
OPERATION
Enter Valet Mode:
1. With the unit Disarmed, turn the ignition to ON position.
2. Press and hold valet/program switch for 2 seconds until the LED turns ON. The LED wills remain on as long as the system is in Valet Mode.
Remote
Door
Lock
Remote
Door
Unlock
Exit Valet Mode:
1. To return to normal operation, turn the ignition
ON.
2. Press and hold the valet/program switch for 2 seconds. The LED will turn OFF indicating the system has exited Valet
Mode.
REMOTE VALET: (System in Disarm or Valet mode)
Press and release the button on the transmitter (3) times within 3 seconds to enter / exit valet mode. (1) parking flash confirms entering
Valet Mode and (2) parking light flashes confirms exiting of valet mode.
N. CAR FINDER
In armed mode, press the button to active car locator function. The siren will chirp (6) times. The parking light will flash (12) times, for you to easily locate your car.
10
. .
OPERATION
O. PANIC MODE:
The transmitter can be used as a remote panic switch to manually trigger the alarm in case emergency.
1. Press and hold the button for 3 second. The alarm will immediately sound.
2. During Panic Mode, the normal function of this transmitter button will be suspended. The and buttons can be used to lock and unlock the doors (if the option is installed), however once the button is pressed, the vehicles starter disable device, (if installed) will be enable allowing the vehicle to start.
3. To stop the Panic Mode, press and hold the or buttons on the transmitter again for 3 seconds, if any transmitter button other than the
or button is pressed and released, the Panic Mode will be turned off immediately.
4. If the button is not pressed, the alarm will automatically stop after 30 seconds.
P. SYSTEMS STATUS CHECK
When you want to check the systems present status through the LCD screen, Press the transceiver button (2) times, within 3 seconds press the (SET) button. It responds with one melody sound, the LCD screen should be illuminated.
Note: If there is no responce then you are out of range.
Q. DOME LIGHT SUPERVISION
The alarm has a unique feature that will turn ON your vehicles dome light as follows:
1. Upon disarming, the interior dome light will remain ON for 30 seconds.
2. If the vehicle is intruded, the interior dome light will flash for the same duration as the siren.
Note: Turning on the ignition switch or arming the alarm will turn
off the dome light.
R. IGNITION CONTROLLED DOOR LOCK/UNLOCK.
If the vehicles door locks have been interfaced to the security systems keyless entry, the system will automatically lock the vehicle's doors when the ignition is turned ON and will unlock the vehicles doors when the ignition is turned OFF.
11
. .
OPERATION
S. TRUNK RELEASE (CHANNEL 3) OUTPUT.
Press and hold the button on the transmitter for two seconds to remote control the trunk release or other connected electronic devices.
T. CHANNEL 4 TIMER CONTROL OUTPUT
Press the transmitters (4) and (4) buttons at the same time to active the Channel 4 function. Channel 4 is user-programmable timer output. You may program the built-in timer to send a ground signal for any time duration from 1 second to 120 seconds. For instance, this timer output may be used to turn on the headlights, power windows or sunroof.
(Factory defaults setting at momentary output.)
U. CHANNEL 5 TIMER CONTROL OUTPUT
Press the transmitters (5) and (5) buttons at the same time to active the Channel 5 function. Channel 5 is user-programmable timer output.
You may program the built-in timer to send a ground signal for any time duration from 1 second to 120 seconds. For instance, this timer output may be used to turn on the headlights, power windows or sunroof. (Factory defaults setting at momentary output.)
V. CHANNEL 6 TIMER CONTROL OUTPUT
Press the transmitters (6) and (6) buttons at the same time to active
Channel 6 function. Channel 6 is user-programmable timer output. You may program the built-in timer to send a ground signal for any time duration from 1 second to 120 seconds. For instance, this timer output may be used to turn on the headlights, power windows or sunroof. (Factory defaults setting at momentary output.)
12
. .
OPERATION
For 2-way LCD Remote Control Transceiver:
2nd Car Operation:
1. Press the SET button first, within 3 seconds press and hold the and buttons together for 2 seconds with two beeping sounds and the icon will display on the LCD screen to indicate the second transceiver pin code has been learned.
2. With the icon displayed on the LCD screen, you can remote control and communicate with the second vehicles security system. It has two short bi sounds while pressing the button of the LCD screen transceiver.
Back to 1st Car Operation:
1. Press the SET button first, within 3 seconds press and hold the and buttons together for 2 seconds with one long beeping sound, the screen to indicate the system is back to first transceiver pin code.
2. While the
timer icon will display on the LCD
timer icon is displayed on the LCD screen, you can remote control and communicate with the first vehicles security system. It has one short bi sound while pressing the button of the LCD screen transceiver.
13
. .
OPERATION
A. TO REMOTE START THE VEHICLE:
When you want to Remote Start your vehicle,
1. Press the button twice on the transmitter
2. The parking light will flash to indicate the remote starter received the signal. (A melody sounding from your Remote
LCD transceiver and the icon will flash on the LCD screen to confirm the remote starter was activated.)
3. The engine will start in approximately 5 seconds.
4. Once the engine is running, after couple seconds the parking light will turn on and climate controls will activate and adjust the vehicles interior temperature to your preset setting.
(While the vehicle is running, the icon and the minutes digit on the LCD screen will flash and it will indicate a count down timer based on the 5, 10, 20 or 30 minute run time you have selected)
5. The vehicle will run for 5 to 30 minutes and automatically
Activate
Remote
Start
Engine
Running shut down. (When the unit shuts off the count down timer will turn off and the transmitter will play a melody.)
NOTE: The Remote Start Unit will not start the vehicle if any one of the followingconditions exists:
1. The hood is opened.
2. The brake pedal is pressed.
3. Move the optional remote start enable toggle switch to OFF position.
(If installed)
4. The gear selector is in any gear other then PARK or NEUTRAL
5. The e-brake is not set. (for Standard Transmission Vehicle)
SAFE START (Child safety mode)
(Factory defaults setting) press the button twice on the transmitter to start the vehicle. Programming this feature will eliminate an accidental remote start, when kids enter this transmitter, it enquires:
The user presses the transmitters and buttons at the same time to remote start the vehicle.
14
. .
OPERATION
B. ENGINE START MEMORIZING FOR VEHICLES WITH MANUAL
TRANSMISSIONS
The system senses the neutral transmission position automatically and there is no prior set-up required. The system in the standard transmission vehicle operates a process that when you exit the vehicle it senses and memorizes the neutral transmission position. If the vehicle is equipped with a automatic transmission, this process is omitted.
1. While engine is running with ignition key, set the emergency brake and place the transmission in the neutral position.
2. Before turning off the engine, press the button twice on the transmitter.
-- The LED indicator will flash 3 times to confirm it is entered.
3. Turn off the Ignition Key and remove it from the key cylinder.
-- The engine will continue running until the pre-programmed time elapsed or a shutdown input is received.--
4. Exit the vehicle, close all doors.
-- The engine should still continue running, this is a normal operating process.
5. Within 1 minute from the time of step 1, press the button on the transmitter to lock the doors.
6-1. If the engine shuts down immediately and the system is now ready for next remote (or programmable) engine starts.
6-2. If the engine does not shut down immediately, the system has failed in engine start memorize set up, repeat above process again.
If a door is opened after the above process, the prior memorization for the next remote or programmed engine start sequence was delete and the function shall not work until you repeat above process again.
Note: If the engine start memorize is set up, the dome light supervision function will be temporarily by-passed.
C. TO OPERATE THE VEHICLE
WHILE RUNNING IN THE REMOTE START MODE:
To operate the vehicle while running in the remote start mode:
Insert the ignition key and turn it to the ON (not the start) position.
Press the brake pedal.
Note: If the brake pedal is pressed before the key is in the ON position, the engine will shut down.
15
. .
OPERATION
D. PIT-STOP FEATURE:
This feature allows the vehicle to remain running after the key has been removed from the ignition switch. This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but would like to leave the engine running and the climate control on.
1. Before turning off the engine, press the button twice on the transmitter and the LED indicator will flash 3 times to confirm the program was entered.
2. Turn the ignition key to the OFF position. (The engine will stay running.)
3. The engine will run until the pre-programmed time elapsed or a shutdown input is received.
Note: For Standard Transmission Vehicles: Before pressing the button, set the emergency brake first.
E. TURBO COOL-DOWN TIMER MODE: (See Alarm Feature 2 - 5
Programming)
Turbo Cool Down timer mode keeps the engine running after arriving at your destination for a programmable period of 1, 3 or 5 minutes, This allows the systems run time to conveniently cool down the turbo after you have left the vehicle. To activate:
1. While engine is running, place the transmission in the park position and set the emergency brake.
2. Before turning off the engine, press and release the and buttons at the same time.
-- The parking light wills turn on to indicate the remote starter has entered turbo cool down mode. --
3. Turn the ignition key OFF and remove it from the key cylinder.
-- The engine will remain running. --
4. Exit and secure(lock) the vehicle.
-- The engine will remain running until the pre-programmed time has elapsed.
F. TIMER / TEMPERATURE START:
This unit can be programmed to start and run the engine every 2 or 3
hours or punctually at the same time the next morning, the engine will run for the programmed running time and then shut down.
IMPORTANT: Timer Start should be used only in open areas, never start and run the vehicle in an enclosed space such as a garage or carport.
16
. .
OPERATION
2 to 3 hour Timer Start with Temperature-Control OFF: This feature is design for an extreme cold climate usage. The system will automatically start the vehicle every 2 or 3 hours, to prevent the engine from freezing and to prevent a vehicle from being hard to start.
A MAXIMUM OF SIX CYCLES CAN OCCUR.
2 to 3 hour timer start with Temperature-control:
If you programmed the temperature ON to operate. The system can be programmed to automatically start the vehicles engine whenever the temperature inside the vehicle reaches or drops below the preprogrammed temperature level. The system will monitor the air temperature every 2 to
3 hours and will only start the engine during extreme cold temperatures.
There are (3) three temperature levels to choose from.
Daily Timer Start: This feature is very useful for the driver who wants to run the vehicle punctually at the same time the next morning. Before setting up the Daily Timer Start, you should set you time for engine start. ( see Timer Setting / Timer set-up for Daily Timer Start, page 16)
To ENTER:
1. Press the button twice to remote start the vehicle. As soon as the vehicle is running the parking lights will turn on or start flashing.
2. Immediately depress the button once, within 2 seconds.
3-a. 2 to 3 Hour Timer Start: Rapidly depresses the button. The parking light will flash (3) times. The siren or horn chirps (3) times. The vehicle is now programmed to start every 2 to 3 hours.
3-b. Daily Timer Start: Depress the transceiver SET button first, within 3 seconds press ( ) button. The parking lights will flash (6) times. The siren chirps (6) times. The vehicle is now programmed to start at this set time, the next day. Your set time for the next day, the engine start flashes for approx. 3 seconds on the LCD screen. After 3 seconds the icon stays displayed on the LCD screen.
4. Press the brake pedal to shut the engine off.
17
. .
REMOTE START OPERATION
Exit the timer start:
1. Timer start can be exited manually as follows:
Make sure the engine is not running in remote start mode.
2. Turn the ignition key ON. The LED and parking lights will flash (4) times.
Or
The horn chirps (4) times.
1. Press the button twice to remote start the vehicle. As soon as the vehicle is running and the parking light have turned on or are flashing.
2. Immediately depress the button, then press and hold the button for 2 seconds. The parking lights will flash (4) times. The siren or horn chirps (4) times. The vehicle is no longer programmed to start automatically.
G. INTERIOR TEMPERATURE MONITOR
You can monitor through the LCD screen, the present interior temperature of the passenger compartment before cooling or heating your vehicle. Press the transceiver SET button first, within 3 seconds press the ( ) button; the interior temperature will be shown on the LCD screen. This reading may be higher than actual ambient temperature due to the greenhouse effect and is relative only the inside vehicle temperature.
H. TO TURN OFF THE REMOTE START:
When the engine is running (in remote start mode), to shut the engine off: Press the button twice on the remote transmitter.
Move the optional remote start enable toggle switch to the
OFF position. (If installed) Press the brake pedal. Release the emergency brake. (for Standard Transmission Vehicle) The vehicle will shut down and turn off the parking lights to indicate engine has stopped.
18
. .
REMOTE START OPERATION
I. SHUT-DOWN INPUT FOR REMOTE STARTER:
If any of the following conditions exists while the system is operating, the engine will not start or will shut down immediately:
1. The hood is opened.
2. The brake pedal is pressed.
3. The emergency brake is released (for Standard Transmission Vehicle)
4. Engine is over-revved. {Tachometer checking type only}
5. The pre-programmed run time (5 /10 / 20 / 30 minutes) has elapsed.
6. Pressing button twice on the remote transmitter.
7. Move the optional remote start enable toggle switch to OFF position.
(If installed)
8. If the engine does not start with {3} attempts.
J. DISABLING THE REMOTE START SYSTEM: (If installed)
This feature allows your systems remote starter to be temporarily disabled to prevent the vehicle from being remote started accidentally. This feature is useful if the vehicle is being serviced or stored in an enclosed area. To disable the remote starter, move the optional remote start enable toggle switch to the OFF position.
LCD REMOTE TRANSCEIVER:
Note: the system may be interfered with by stronger radio frequency, sources of high voltage electric power lines or obstacles such as tall buildings, the transmission range may be shorten due to the systems use of a low powered output frequency.
19
. .
REMOTE START OPERATION
K. BATTERY REPLACEMENT:
A 1.5V type AAA Alkaline battery powers the Remote Transceiver. When the power of the battery weakens a icon will be displayed on the LCD screen.
When the old battery is replaced with a new one, there will be beep sound that indicates the power is up and the clock on the LCD screen returns to
AM12:00 after displaying all the icons. Set the correct time by pressing for
3 seconds before using. (See Timer Setting).
Note : Press the button two times with the battery removed, then
insert the new battery.
L. THE REMOTE LCD ICON DESCRIPTION CHART :
ARMED
Door Lock
Your vehicle doors are locked.
Armed Mode
Your vehicle is in armed mode.
Remote Transmission
You are transmitting the signal to the control unit.
Door Unlock
Your vehicle doors are unlocked.
Valet Mode
All the functions are temporarily on hold.
In-Range Indicator
The system is within the remote control range.
Door Open Warning
Doors are opened.
(Zone 3)
Shock Sensor Trigger
Trigger on Shock Sensor
(Zone 4)
Trunk/Hood Trigger
Trunk or Hood is opened.
(Zone 2)
Warn Away Trigger
Trigger on Shock Sensor
(Zone 1)
Engine Starting
Your vehicles engine is starting by remote control.
Timer Control Start
Engine will automatically start at the same time the next day or every 2 to 3 hours.
Engine Running
Your vehicles engine is running in remote start mode.
Temperature Monitor
The interior temperature of your vehicle.
20
. .
REMOTE START OPERATION
Time Monitor Alert Alarm
You have set the morning call alarm.
Power Save Mode
Saves the battery power.
Count Down (Parking) Timer
Reminder when your time is up for parking.
Vibration Mode
Remote control vibrate when the system is triggered.
Low Battery
You must replace the battery in the remote control.
Button Lock
Disable the transmission functions temporarily.
M.PROGRAMMING THE LCD REMOTE TRANSMITTER:
Transmitter Description Operation
Button
SET (1 second)LCD screen lamp turns on for 5 seconds.
SET (3 seconds)Timer Programming Mode.
Press and hold for 1 sec.
1 melody sound to confirm enters.
Press and hold for 3 sec.
2-melody sounds to confirm enter.
SET (5 seconds)Power Save Mode Press and hold for 5 sec.
1 Melody sound to confirm enters.
SET- SET- SET Clear the Flash Icon and
Melody Sound on the LCD
Screen Transmitter
Press within 3 sec.
SET- (2-sec.) Button Lock ( ) enable/disable Press within 3 sec.
SET- (2-sec.) Melody / Vibration ( ) Mode Press within 3 sec.
21
. .
REMOTE START OPERATION
Transmitter
Button
Description Operation
SET- (2-sec.) Program Count Down Timer ( ) Press within 3 seconds
(10-Minute/20M/30 M/1Hour/
1.5H/2.0H)
*let the buttons start counting down then flashes
SET - (2-sec.) Enable/Disable Beep Sound (Bi)
While Pressing Button
1. Screen Lamp ON: Press and hold the SET button one second, with one melody sound and the LCD screen lamp will turns on for 5 seconds.
2. Power Save Mode: While the power save mode, the LCD remote transceiver uses 0 current to save the battery power.
Entry: Press & hold the SET button for 5 seconds, with one melody sound and SAVE icon on the LCD screen to indicate entry the power save mode. Exit: Press any button of the LCD remote transmitter to exit the Power Save Mode.
3. Clear the Flash Icon and Melody Sound: Press the SET button 3 times within
3 seconds will clear the flash icon and melody sound on the LCD screen transceiver
4. Stop The Trigger Melody Sound: While triggering the alarm the LCD screen will alert user through melody sound and flashing trigger icon, press any button on the LCD remote transmitter to stop the melody sound only.
5. Button Lock: It is useful if you want to disable the transmission function of the remote control temporarily to prevent from any inadvertent pressing of buttons by others. Press the SET button first, within 3 seconds press and hold the ( ) button for 2 seconds to activate or cancel the button lock function, the icon will displayed on the LCD screen to show the LCD remote transmitter is on
Button Lock.
6. Vibration / Melody Mode:
It is useful when you are in a noisy place and difficult to hear beep sound from the remote control as the remote control in
Press the SET button first, within 3 seconds press and hold the ( ) button for 2 seconds to select the mode of vibration or melody, the icon will displayed on the LCD screen to show the LCD remote transceiver is on vibration mode.
22
. .
LCD REMOTE CONTROL TRANSCEIVER
7. Enable / Disable Beep Sound While Pressing Button:
It has a short bi sound while pressing the button of the LCD screen transceiver. If you want mute the bi sound mute always while press button. Press the button first, within 3 seconds press and hold the
(Bi) button for 2 seconds to disable the beep sound.
8. Low Battery Indication:
When the power of the battery weakens, it has two short beep sound and flash icon while pressing the button of the LCD screen transceiver.
9. Set Up Fixed Count Down Timer:
1. Press the SET button first, within 3 seconds press and hold the
( ) button for 2 seconds, the LCD screen will shows icon and timer
(ie. 0:10).
2. Press the ( ) button again showing next order time on the screen
(ie.0:20), press them again (ie.0:30) ..and so on.
3. Leave the buttons starting count down then icon flashes.
Note:
1. The count down period is fixed as 10 minutes, 20 minutes, 30 minutes,
1 hour, 1.5 hours and 2 hours maximum.
2. When count down timer showing 0:00 means to turn off the timer.
3. Press the SET button for real time indication when the timer is counting down.
10. Out Of Range Indication:
The system will automatically check the range every 20 minutes after armed.
1. If user is within the range, the icon will display on the LCD screen.
2. If user is out of range, it has five short bi sounds and the icon will disappear on the LCD screen.
TIMER SETTING CHART:
Transceiver
Button Description
Press
Transceiver Button
for and for + 1 Press and hold the
SET button for 3 sec.
Timer Setting (Hour)
*Flash digit for adjusting
Press the SET button once Time setting (Minute)
*Flash digit for adjusting
for and for +
23
. .
LCD REMOTE CONTROL TRANSCEIVER
Transceiver
Button Description
2 Press the SET button once. Alert Alarm
Time Setting (Hour)
*Flash digit for adjusting
Press the SET button once Alert Alarm
Time Setting (Minute)
*Flash digit for adjusting
Press
Transceiver Button
for and or +
for and for +
Press the SET button once Alert Alarm Setting ON/OFF for OFFand for ON
3 Press the SET button once Count Down
Timer Setting (Hour)
*Flash digit for adjusting
(Max.19 hours 59 minutes)
for and for +
Press the SET button once Count down Timer Setting for and for +
(Minute)
*Flash digit for adjusting
Press the SET button once Count down Timer
Setting ON/OFF
for OFFand for ON
4 Press and hold the button for 2 seconds.
Daily Timer Start Timer
Setting Flash / icon and Hours for adjusting
for and for +
EXIT: Press and hold the SET button for 2 seconds or leave it for 10 seconds and the system will automatically exit the programming mode.
24
. .
LCD REMOTE CONTROL TRANSCEIVER
EXIT: Press and hold the SET button for 2 seconds or leave it for 10 seconds, the system will exit the programming mode.
1. Timer Setting: Example to AM10:30
1. Press and hold the SET button for 3 seconds, with two-melody sound and the Hours digit flashes for adjusting.
2. Press the or button to decrease or increase the Hour digit until AM10:xx.
3. Press the SET button once again then the Minute digit flashes for adjusting.
4. Press the or button to decrease or increase the Minutes digit until AM 10:30.
5. Press the SET button for 2 seconds with one-melody sound to confirm exiting the timer program mode.
2. Alert Alarm Timer Setting: Example to PM 6:30
1. Press and hold the SET button for 3 seconds, with two-melody sound and the Hours digit flashes for adjusting.
2. Press the SET button twice, the LCD screen will shows icon and
Hours digit is flashes for adjusting.
3. Press the or buttons to decrease or increase the Hour digit until PM 6:xx.
4. Press the SET button once again then the Minutes digit flashes for adjusting.
5. Press the or button to decrease or increase the Minutes digit until PM 6:30.
6. Press the SET button once again then icon flashes for alert alarm
ON/ OFF setting
7. Press the button to start the Alert Alarm Timer, and the ON icon will show on the LCD screen. Press the button to stop the
Alert Alarm Timer, and the OFF icon will show on the LCD screen.
8. Press SET button for 2 seconds with one-melody sound to confirm exit the timer program mode.
25
. .
LCD REMOTE CONTROL TRANSCEIVER
3. Count Down Timer Setting: Example Set count down timer at 2:30
1. Press and hold the SET button for 3 seconds, with two-melody sound and the Hours digit flashes for adjusting.
2. Press the SET button 5 times, the LCD screen will shows icon and
Hours digit is flashes for adjusting.
3. Press the or button to decrease or increase the Hour digit until
2:xx.
4. Press the SET button once again then the Minutes digit flashes for adjusting.
5. Press the or button to decrease or increase the Minute digit until 2:30.
6. Press the SET button once again then icon flashes for alert alarm
ON / OFF setting
7. Press the button to start the count down timer, and the ON icon will show on the LCD screen. Press the button to stop the count down timer, and the OFF icon will show on the LCD screen.
8. Press the SET button for 2 seconds with one-melody sound to confirm exit the timer program mode.
Note: Maximum is 19 hours.
4. Time Set-Up For Daily Timer Start: Example to AM 6:30
1. Press and hold the SET button for 3 seconds, with two-melody sound and the Hours digit flashes for adjusting.
2. Press and hold the button for 2 seconds, the LCD screen will flash
/ icon and Hours digit for Hour set-up.
3. Press the or button to decrease or increase the hour digit until
AM 6:00.
4. Press the SET button once again then the minute digit flashes.
5. Press the or button to decrease or increase the minutes digit until
AM 6:30.
6. Press the SET button for 2 seconds with one-melody sound to confirm exit the timer program mode.
26
. .
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 4 Important Notice
- 5 A. REMOTE TRANSMITTER OPERATION
- 6 B. TWO-WAY TRANSEIVER REMOTE CONTROL OPERATION
- 6 C. LED DISPLAY CHART
- 6 D. CHIRP INDICATOR
- 6 E. PARKING LIGHT INDICATOR DISPLAY
- 7 F. ALARM OPERATING CONDITION
- 7 G. ACTIVE ARMING
- 8 H. SILENT ARMING / DISARMING
- 8 I. PASSIVE STARTER DISABLE
- 8 J. PASSIVE ARMING
- 9 K. ACTIVE DISARMING
- 9 L. DISARMING WITHOUT A TRANSMITTER
- 9 M. VALET MODE
- 10 N. CAR FINDER
- 11 O. PANIC MODE
- 11 P. SYSTEM STATUS CHECK
- 11 Q. DOME LIGHT SUPERVISION
- 11 R. IGNITION CONTROLLED DOOR LOCKS
- 12 S. TRUNK RELEASE
- 12 T. CHANNEL 4 TIMER OUTPUT
- 12 U. CHANNEL 5 TIMER OUTPUT
- 12 V. CHANNEL 6 TIMER OUTPUT
- 14 A. TO REMOTE START THE VEHICLE
- 16 D. PIT STOP FEATURE
- 16 E. TURBO MODE
- 16 F. TIMER/TEMPERATURE START
- 18 G. INTERIOR TEMPERATURE MONITOR
- 18 H. HOW TO TURN OFF THE REMOTE STARTER
- 19 I. SHUT-DOWN INPUTS
- 19 J . DISABLING THE REMOTE STARTER
- 20 K. BATTERY REPLACEMENT
- 20 L. REMOTE ICON DESCRIPTION CHART
- 21 M. PROGRAMMING THE REMOTE TRANSMITTER