Crosley KAMELEON User`s guide

Crosley KAMELEON User`s guide
OFA Kameleon wRF UG rev 3.fm Page 1 Monday, September 13, 2004 11:18 AM
8-Device
Universal Remote Control
With IR/RF Base Station
URC-9964B00
User’s Guide
OFA Kameleon wRF UG rev 3.fm Page 2 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . .3
Installing Batteries . . . . . . . . . . . . . . . . . . .4
How Kameleon™ Works . . . . . . . . . . . . . . .5
Features And Functions. . . . . . . . . . . . . . . .6
Key Charts. . . . . . . . . . . . . . . . . . . . . . . .7
Device Table . . . . . . . . . . . . . . . . . . . . .12
Adjusting The Display. . . . . . . . . . . . . . . . .13
Adjusting Brightness. . . . . . . . . . . . . . .13
Adjusting How Long The Screen Light is
On . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Setting the Vibration Switch . . . . . . . . .15
Programming Device Control . . . . . . . . . .15
Programming Combo Device Control . . . .17
Searching For Your Code. . . . . . . . . . . . . .19
Checking The Codes . . . . . . . . . . . . . . . . .20
Using The Home Theater Mode . . . . . . . . .21
Control Organization. . . . . . . . . . . . . . .21
Programming The Home Theater Mode 22
Using the IR/RF Base Station. . . . . . . . . . .24
Setting Up the IR/RF Base Station . . . .24
Adding the IR Signal Extension Cord . .25
Optimizing IR/RF Base Station
Reception . . . . . . . . . . . . . . . . . . . . . . .26
Changing Volume Lock . . . . . . . . . . . . . . .27
Using Macros . . . . . . . . . . . . . . . . . . . . . . .29
Programming a Favorite Channel
Macro . . . . . . . . . . . . . . . . . . . . . . . . . .30
Programming a Master Power Macro in
the Home Theater Mode . . . . . . . . . . . .31
Clearing a Macro . . . . . . . . . . . . . . . . .32
Using Learning . . . . . . . . . . . . . . . . . . . . . .32
Learning Precautions . . . . . . . . . . . . . .32
Programming a Learning Key . . . . . . . .33
Deleting a Single Learning Key. . . . . . .34
Deleting All Learned Keys in a Specific
Mode.. . . . . . . . . . . . . . . . . . . . . . . . . . .35
Reassigning Device Keys . . . . . . . . . . . . . .36
Using Keymover . . . . . . . . . . . . . . . . . . . . .36
Programming Keymover . . . . . . . . . . . .37
Restoring a Single Keymoved Key . . . .38
Restoring All Keymoved Keys in a Single
Mode . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Using Channel Scan . . . . . . . . . . . . . . . . . .39
Programming Favorite Channel Scan . . . .39
Restoring Factory Default Settings . . . . . .40
Clearing All Custom Programming . . . . . .41
2
Manufacturer’s Codes . . . . . . . . . . . . . . . .42
Setup Codes for Audio Amplifiers. . . . . 42
Setup Codes for Audio Receivers. . . . . 42
Setup Codes for Cable Boxes . . . . . . . . 43
Setup Codes for CD Players . . . . . . . . .43
Setup Codes for DVD Players . . . . . . . . 44
Setup Codes for DVD Player/PVR
Combos . . . . . . . . . . . . . . . . . . . . . . . . . 45
Setup Codes for DVD Player/VCR Combos
(DVD Codes) . . . . . . . . . . . . . . . . . . . . . 45
Setup Codes for Home Automation . . . 45
Setup Codes for Home-Theater-in-a-Box
Systems (Receiver Codes) . . . . . . . . . . 46
Setup Codes for Mini-Disc Players. . . .46
Setup Codes for PVRs. . . . . . . . . . . . . . 46
Setup Codes for Satellite Receivers . . 46
Setup Codes for Satellite Receivers/PVR
Combos . . . . . . . . . . . . . . . . . . . . . . . . . 47
Setup Codes for TVs . . . . . . . . . . . . . . . 47
Setup Codes for TV/DVD Player Combos
(TV Codes). . . . . . . . . . . . . . . . . . . . . . . 49
Setup Codes for TV/VCR Combos (TV
Codes). . . . . . . . . . . . . . . . . . . . . . . . . . 49
Setup Codes for TV/VCR/DVD Player
Combos . . . . . . . . . . . . . . . . . . . . . . . . . 50
Setup Codes for VCRs. . . . . . . . . . . . . . 50
Setup Codes for Video Accessories . . . 52
About Upgrading . . . . . . . . . . . . . . . . . . . . 52
Upgrade Procedure . . . . . . . . . . . . . . . 53
Upgrade Exclusions . . . . . . . . . . . . . . . 53
Troubleshooting . . . . . . . . . . . . . . . . . . . . .54
Device Menu Screens . . . . . . . . . . . . . . . . 56
Customer Support . . . . . . . . . . . . . . . . . . . 65
Compliance with FCC Rules and
Regulations . . . . . . . . . . . . . . . . . . . . . . . . 65
Limited Warranty . . . . . . . . . . . . . . . . . . . . 65
Battery Use And Safety . . . . . . . . . . . . . . . 66
About Battery Life . . . . . . . . . . . . . . . . . . . 66
Specifications . . . . . . . . . . . . . . . . . . . . . . 67
Additional Information. . . . . . . . . . . . . . . .67
Table of Contents
OFA Kameleon wRF UG rev 3.fm Page 3 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
INTRODUCTION
The OFA Kameleon™ 8-Device Remote with RF (URC-9964B00) is a
revolutionary universal remote control that uses Universal Electronics’ Kameleon
Technology. Moreover, it allows you to consolidate the clutter of all of your
original remote controls into one easy-to-use product.Advanced features include:
•
Kameleon Technology – dynamic menu screens that respond to device
selection and illuminate only active keys
•
Home Theater Mode – a custom mode that groups the most-oftenused keys together for operating convenience in one mode
•
Macros – for instant activation of favorite
key sequences
•
Learning – to capture unique functions from your devices’ original
remote controls
•
Key Mover – for copying keys from one device to another, or to a
different position in the same mode
•
Direct Code Setup – for easy device programming with setup codes
•
Innovative Code Search – allows setup of your devices without looking
up codes
•
IR/RF Base station–for extended remote control signal range
•
Favorite Channel Scan – for easy channel surfing of favorite channels
•
Volume Lock – to assign volume controls to individual devices or to
one global device
•
Extensive Code Library – largest and most efficient group of IR
remote control codes for virtually every current brand and make
•
Upgradeability – our unique telephone upgrade system ensures your
remote control always has the latest setup codes when adding new
devices in the future
After installing four (4) new AAA alkaline batteries (not included, see next
page), you can immediately use the unit to control a Motorola Cable Box, a
Toshiba DVD Player, a Philips Tivo PVR (DVR), a Pioneer CD Player and
Audio Receiver, and a RCA TV,VCR, and Satellite Receiver. To control other
brands than the default ones, see Programming Device Control on page 15.
Introduction
3
OFA Kameleon wRF UG rev 3.fm Page 4 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
INSTALLING BATTERIES
❶
❷
NOTE: The two bottom segments of
the IR indicator flash when the
batteries are running low. The
batteries need replacement if one of
the following conditions occurs:
1.
Pressing any key turns on all
keys and icons.
2.
The vibration switch no longer
activates the display (if the
vibration switch feature is still
enabled).
3.
Pressing a key while the screen
is off causes all of the keys and
icons to turn on.
See “Battery Use And Safety” on
page 66 for additional information.
❸
1.
On the remote control’s back, push the tab and lift off the battery cover.
2.
Obtain four (4) new AAA alkaline batteries. Match the + and – marks
on the batteries to the + and – marks in the battery case, then insert the
new batteries.
3.
Press the battery cover back into place. The tab should click when the
cover is locked.
4.
Once the batteries are inserted correctly, press anywhere in the middle part
of the screen. The display will turn on and show all keys. If a key is not
pressed after the display turns on, the display will turn off. The display can
be turned on by moving the unit or by pressing on the center of the screen.
4
Installing Batteries
OFA Kameleon wRF UG rev 3.fm Page 5 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
HOW KAMELEON™ WORKS
Kameleon™ allows wireless controllers to dynamically change their
appearance and functionality, to match the home entertainment
environment.Moreover, this technology provides unparalleled ease-of-use
and superior control by delivering a uniquely intuitive, graphical interface
that intelligently illuminates only the active keys.
The OFA Kameleon 8-Device Remote with RF uses Kameleon technology to
provide the versatility of an LCD remote control with the feel of a traditional
push button unit. The result is a stunning, bright display with engaging
animation and touch-sensitive graphics for the user.
The remote control includes convenient Menu Driven programming.The
displays are divided into two types of interactive screens: Device Menus for
normal remote control use, and Programming Menus for feature
setup.Acting like its namesake, Kameleon changes the Device Menu for the
device being selected. For example, selecting TV displays a main menu that
contains channel selection, volume control, and a keypad.However, selecting
a DVD player still displays a menu with those same keys as the TV, but now
navigation keys and transport controls are added for the DVD device.
Several devices have additional menus that can be accessed using SCROLL
(see Device Menu Screens, starting on page 56. For example, TV has three
menus: a main menu with keys for a general purpose TV, a second menu
screen that adds navigation keys and removes FORMAT, INPUT and ENTER
keys, and a third menu screen that adds INPUT, ENTER, and PIP keys.
Depending on desired features, a user has the flexibility to use any menu
screen that works best for the selected device.
NOTE: The CD, DVD, and PVR modes do not have additional menu
screens even though SCROLL is displayed.
Animated key graphics also provided enhanced operational feedback, so the
user can easily see what mode is active and when the commands are
communicating with a device. The end result of Kameleon technology is a
simple, elegant, and intelligent way of organizing a large number of remote
control keys for eight different devices in a relatively small case.
How Kameleon™ Works
5
OFA Kameleon wRF UG rev 3.fm Page 6 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
FEATURES AND FUNCTIONS
Use the illustration to the right to locate
features on the OFA Kameleon 8-Device
Remote with RF (URC-9960) and then refer
to the Key Charts (starting on page 7) to
learn how they function.
NOTE: The illustration shows all remote
control keys. In actual operation, only
active keys used by the selected device are
displayed and non-active keys are hidden.
To find out what type of devices can be
controlled by each device key after
programming, see the Device Table on
page 12.
6
Features And Functions
OFA Kameleon wRF UG rev 3.fm Page 7 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
KEY CHARTS.
When a key is pressed, the IR Segments animate.
Outgoing animation (see arrows) indicates the remote
control is sending IR signals to a selected device.
Incoming animation (see arrows) indicates the remote
control is receiving IR signals from a device being
learned (see Using Learning on page 32)
Press a Device Key once to select a home
entertainment device to control (e.g., DVD).When
selected, the Device Key animates to indicate it is
currently active.Also see the Device Table on page 12.
After programming, press the Home Theater key once
to select the home theater mode (see Using The Home
Theater Mode on page 21).
Press POWER once to turn on or off a selected device.
During programming, the HOME key appears. Use it to
exit the program screen or to return to the lastselected device key screen.
In the AUX, CBL/SAT, and TV modes, use FAV to scan
through all channels, or after programming, to scan
through 10 favorite channels.
In the AUX, CBL/SAT, TV, AUDIO, and VCR modes, use
SCROLL to view additional key screens for the selected
device.
Use VOL (or VOL ) to raise (or lower) the sound
volume for the selected device (also see Changing
Volume Lock on page 27).
Press MUTE once to turn the sound off or on.
Features And Functions
7
OFA Kameleon wRF UG rev 3.fm Page 8 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
In the AUX and CBL/SAT modes, use PVR/VOD to access
PVR/VOD programs (if available on your cable or
satellite service).
In the AUDIO mode, use PRESET to access preset
stations on your audio device.
In the TV mode, use FORMAT to change the aspect ratio
or zoom (if feature is available on your TV).
In the DVD or PVR mode, press REPLAY once to replay a
DVD chapter or a recorded program on your PVR (or
DVR).
In the CBL/SAT and AUX modes, press SCROLL once to
display REPLAY and then press REPLAY once to replay a
VOD program (if available on your cable or satellite
service).
or
Use CH (or CH
lower) channel.
) to select the next higher (or
In all modes except CD, DVD, and PVR, press LAST once
to recall the last channel.
In the PVR mode, use LAST to select live or recorded
video.
In the CD or DVD modes, press RAND to play random
tracks or chapters.
In the AUX and CBL/SAT modes, use PAGE+ or PAGE–
to page up or down through channels in the program
guide.
In the DVD mode, press AUDIO once to access DVD
audio formats (if available).
In all modes except AUDIO, use GUIDE to display your
selected device’s program guide or setup menu.
In the AUDIO mode, use DSP to access DSP features (if
available) on your audio device.
Use INFO to display the current channel and program
information.
8
Features And Functions
OFA Kameleon wRF UG rev 3.fm Page 9 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
In the AUX, CBL/SAT, CD, DVD, and PVR modes, use the
Cursor Keys to move the cursor in the program guide
and menu screens.
Use OK to choose options from your selected device’s
menu or guide.
In the TV or VCR mode, press SCROLL once to access
the Cursor and OK Keys.
In the AUDIO mode, press SCROLL twice to access the
Cursor and OK Keys.
In the AUDIO mode, use the Cursor Keys to move the
cursor to select or test surround sound channels on
your audio device.Also see VOL keys (above left).
Use OK to choose options from your audio device’s
menu or guide.
Press MENU once to display your selected device’s main
menu.
Use EXIT to exit from your selected device’s guide or
menu.
In the DVD or AUDIO mode, press SUBTITLE once to
display (or turn off) subtitles, if available on your DVD
or audio device.
or
In all modes except AUDIO, use the Number Keys (1 – 9
and 0) to directly select channels (e.g., 009 or 031) or
enter numbers. In the AUDIO mode, use the Number
Keys to directly select inputs 1 – 9 and 10. To enter
channels in the AUDIO mode, press SCROLL three times
to view channel Number Keys (see above)
Use INPUT to change the input source for a selected
device.
For certain brands in all modes except CD and AUDIO,
press ENTER once after entering numbers (if required
on your original remote control).
Features And Functions
9
OFA Kameleon wRF UG rev 3.fm Page 10 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
For CD or AUDIO modes, press SKIP once to skip to the
next track on your audio device.
After programming, press Macro Key 1 – 4 once to run
a macro (see Using Macros on page 29).
In the CD, DVD, AUDIO, and VCR modes, use the
Transport Keys to control the device’s transport.
or
In the PVR mode, use the LIVE Transport Keys to
control PVR/DVR video.
In the CBL/SAT or AUX mode, press SCROLL once to
display and use the LIVE Transport Keys to control
VOD (Video On Demand) if available on your cable/
satellite service.
In all modes except TV, press G twice to record a
program on your device (if function is available).
In the TV mode, press PIP once (or press SCROLL
twice) to display the PIP Keys.Use them to control the
following Picture-In-Picture features (if available) on
your TV:
Use PIP to switch the Picture-In-Picture feature on or
off.
Use SWAP to switch images and sound between the
main and window pictures.
Use SIZE to select a different picture window size.
Press FREEZE once to capture a frame of video in the
main picture. Press it again to resume normal viewing.
Use MOVE to move the window picture to different
places in the main picture.
Use SETUP to enable the programming screen.
10
Features And Functions
OFA Kameleon wRF UG rev 3.fm Page 11 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
In the program mode, use the Program Keys to
personalize the remote control as follows:
Use DEV SET to program your device codes.See
Programming Device Control on page 15.
Use SEARCH as an alternate way to set up a device by
searching available codes. See Searching For Your Code
on page 19.
Use THEATER to create a custom mode with favorite
remote control keys from different devices in your
home theater system.See Using The Home Theater
Mode on page 21.
Use VOL (Volume Lock) to set volume controls for
individual or global device use.See Changing Volume
Lock on page 27.
Use MACRO to program a series of commands on five
available macro keys. See Using Macros on page 29.
Use
(Brightness) to adjust the brightness level of
the EL display. See Adjusting Brightness on page 13.
Use IR LRN and IR DEL to add and delete key functions
learned from your original device remote controls.See
Using Learning on page 32.
Use MODE to reassign an unused device key to
control a second device.See Reassigning Device
Keys on page 36.
Use OTHER to program other functions. See the Table
of Contents on page 2 for sections on Checking The
Codes, Programming Favorite Channel Scan, Using
Keymover, or Upgrading.
Features And Functions
11
OFA Kameleon wRF UG rev 3.fm Page 12 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
DEVICE TABLE
NOTE: Please refer to the table below when performing the instructions in
“Programming Device Control” on page 15.
After programming, the OFA Kameleon 8-Device Remote with RF will be
able to control the following types of devices:
DEVICE KEY CONTROLS THESE DEVICES
Video Accessory or second device (e.g., Cable Box, Satellite
Receiver, DVD Player, etc.) by reassigning device keys (see
Reassigning Device Keys on page 36)
Cable Box (converter), Cable/DVR Combo, Satellite receiver,
Satellite/PVR Combo
CD Player, Mini Disc player or Home Automation
Television (including HDTV, Plasma and LCD), TV/DVD
Combo (listed as TV Codes), TV/VCR Combo (listed as TV
Codes).
DVD players, Home-Theater-In-A-Box devices (listed as
DVD codes), TV/DVD Player Combo, TV/DVD/VCR Player
Combo, DVD/VCR Player Combo (listed as DVD Codes) or
DVD/PVR Combo
Audio Amplifier, Audio Receiver or Home-Theater-In-ABox devices (listed as Receiver codes under Setup Codes For
Audio Receivers on page 42)
VCR, TV/VCR Combo (listed as VCR Codes) or VCR/DVD
Combo (listed as VCR Codes)
PVR
Note: When programming a code, make sure that the correct mode key is
selected, and that a valid code is programmed for that device (see controls these
devices, above).
12
Features And Functions
OFA Kameleon wRF UG rev 3.fm Page 13 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
ADJUSTING THE DISPLAY
Your new remote has several ways to adjust the display for your comfort and
best use.
ADJUSTING BRIGHTNESS
The OFA Kameleon 8-Device Remote with RF has five levels of brightness
adjustment and is set to the middle one at the factory. To increase or decrease
the brightness, perform the following steps:
NOTE: Increasing the brightness of the display can decrease battery life.
1.
Press and hold SETUP until the two bottom IR segments flash twice. The
Program Keys appear.
NOTE: . If the display turns off because of
inactivity, you must start the programming
sequence again by repeating this step.
2.
Press
(Brightness) once.The Brightness programming screen
appears:
3.
•
To increase brightness, press
one or more times.
•
To decrease brightness, press
one or more times.
When the desired brightness is
achieved, press HOME twice to exit
programming and return to the lastselected device menu screen.
NOTE: Otherwise, to program other features,
press HOME only once to return to the
Program Keys.
Adjusting The Display
13
OFA Kameleon wRF UG rev 3.fm Page 14 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
ADJUSTING HOW LONG THE SCREEN LIGHT IS ON
The OFA Kameleon 8-Device Remote with RF allows you to control how long
the screen light remains on after the last button is pressed. The display-on
time is set at the factory to run for about 8 seconds. To increase or decrease
that time, perform the following steps:
NOTE: Increasing the display on time can decrease battery life.
1.
Press and hold SETUP until the two bottom IR segments flash twice. The
Program Keys appear.
NOTE: . If the display turns off because of
inactivity, you must start the programming
sequence again by repeating this step.
2.
Press OTHER once.The Other programming screen appears:
3.
Using the Number Keys, enter 9 7
8.The bottom two IR segments flash
twice and display the Other screen
again.
4.
Use the following table to choose the
“light on” time:
Press… …to set the light for
5.
14
1
4 seconds
2
8 seconds
3
12 seconds
4
16 seconds
5
20 seconds
Press HOME twice to exit programming and return to the last-selected
device menu screen.
Adjusting The Display
OFA Kameleon wRF UG rev 3.fm Page 15 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
SETTING THE VIBRATION SWITCH
The OFA Kameleon 8-Device Remote with RF is set at the factory to turn the
display on when you pick it up, before you even press a button (the vibration
switch is on). To turn vibration off, perform the following steps.
1.
Press and hold SETUP until the two bottom IR segments flash twice. The
Program Keys appear.
NOTE: Turning off the vibration switch can
significantly extend battery life.
NOTE: If the display turns off because of
inactivity, you must start the programming
sequence again by repeating this step.
2.
Press OTHER once.The Other programming screen appears:
3. Using the Number Keys, enter 9 8 5.
The bottom two IR segments flash four
times, to indicate vibration switch has
been turned off.
4.
Press HOME twice to exit programming
and return to the last-selected device
menu screen.
To turn vibration switch back on, repeat
steps 1 to 4 above. Note that the bottom two
IR segments flash twice (in step 3), to
indicate that the vibration switch is back on.
PROGRAMMING DEVICE CONTROL
The OFA Kameleon 8-Device Remote with RF is preset at the factory to
operate the following devices:
•
RCA TV,VCR, and Satellite
•
Motorola Cable Box (using
Receiver
the AUX key)
•
Toshiba DVD Player
•
Philips Tivo PVR (DVR)
•
Pioneer CD Player and Audio
Receiver
Programming Device Control
15
OFA Kameleon wRF UG rev 3.fm Page 16 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
To control devices other than the default brands, perform the following steps;
otherwise skip this section.
NOTE: . To control a Combo device, perform the instructions in “Programming
DVD Player/VCR Combo Control” on page 17.
1.
Turn on a device (e.g.,VCR or DVD player) and, if applicable, insert
media (e.g., cassette or disc).
NOTE: Read steps 2 through 9 completely before proceeding. Before
starting step 2, review the “Manufacturer’s Codes” (starting on page 42).
Brands are listed alphabetically in order of most popular ones first.
Highlight or write down the devices and the codes you wish to program.
1.
Press and hold SETUP until the two bottom IR segments flash twice. The
Program Keys appear as SETUP flashes repeatedly
NOTE: . If the display turns off due to
inactivity, the remote control exits
programming and return to the last-selected
device menu screen. To start programming
again, repeat this step. To stop programming at
any time, press HOME once to return to the
Program Keys screen. Press HOME once more
to exit completely.
2.
Press DEV SET once. The Device Setup programming screen appears:
3.
Press a device key once (i.e., AUX, CBL/
SAT, CD, TV, DVD, AUDIO, VCR, or PVR).
The selected device key animates.
NOTE: Refer to the Device Table on page
12 when choosing a device key for
programming.
4.
Use the Manufacturer’s Codes (starting
on page 42) to locate the type of device
and brand name and then use the
Number Keys to enter the first code for
your device. The bottom two IR
segments flash twice.
NOTE: If the bottom two IR segments
displayed one long flash, a mistake has
occurred. Try entering the code again.
16
Programming Device Control
OFA Kameleon wRF UG rev 3.fm Page 17 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
5.
Aim the remote control at the device and press POWER once.The device
should turn off. If it does not, repeat steps 5 and 6, trying each code for
your brand until you find one that works. If it still doesn’t work, try
Searching For Your Code on page 19.
NOTE: If the device does not have a POWER key, press the
(Play) key.
6.
If the code works, press OK once.The two bottom IR segments display
one long flash.
7.
If necessary, repeat steps 4 through 7 for each device you want to
control. If finished, press HOME twice to exit programming and return to
the last-selected device menu screen.
8.
For future reference, write down each working device code in the
following boxes:
AUX Code:
TV Code:
Device Type:________________
AUDIO Code:
CBL/SAT Code:
Device Type:________________
Device Type:________________
VCR Code:
CD Code:
Device Type:________________
Device Type:________________
PVR Code:
DVD Code:
Device Type:________________
PROGRAMMING COMBO DEVICE CONTROL
You can set the OFA Kameleon 8-Device Remote with RF to control your
combo devices such as TV/VCR, TV/DVD, Satellite/DVR, Home-Theater-InA-Box, and many others. For a complete list of combo devices, refer to the
device table on page 7. To program a DVD Player/VCR combo, follow the
steps below.
NOTE: Some combo device types have codes that you can program on separate
device keys. For example, you can program DVD Player/VCR Combo codes
Programming Combo Device Control
17
OFA Kameleon wRF UG rev 3.fm Page 18 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
under the VCR or DVD mode keys. Refer to the Setup Codes for DVD Player/
VCR Combos section. You only need to program one code to control your combo
device.
1.
Turn on the DVD Player/VCR Combo and insert a DVD.
NOTE: Please read steps 2 through 8 completely before proceeding. Before
starting step 2, review the “Setup Codes For DVD Player/VCR Combos”
(on page 45). Brands are grouped by VCR codes or DVD codes, and are
listed alphabetically in order of most popular ones first. Highlight or write
down the devices and the codes you wish to program.
2.
Press and hold SETUP until the two bottom IR segments flash twice. The
Program Keys appear as SETUP flashes repeatedly.
NOTE: . If the display turns off due to
inactivity, the remote control exits
programming and return to the last-selected
device menu screen. To start programming
again, repeat this step. To stop programming at
any time, press HOME once to return to the
Program Keys screen. Press HOME once more
to exit completely.
3.
Press DEV SET once.The Device Setup programming screen appears:
4.
Press DVD once (or VCR if your combo
device uses a VCR Code). The key will
animate.
5.
Use the Setup Codes For DVD Player/
VCR Combos (on page 45) to locate
the brand name and then use the
Number Keys to enter the first code for
your device. If performed correctly,
the two bottom IR segments flash
twice.
NOTE: If the two bottom IR segments
displayed one long flash instead, an
error has occurred. Try entering the
same code again.
6.
18
Aim the remote control at the device
and press POWER once. The device
should turn off.
Programming Combo Device Control
OFA Kameleon wRF UG rev 3.fm Page 19 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
7.
If the code works, Press OK once. The two bottom IR segments will flash
twice.
8.
To exit programming, press HOME twice. The display returns to the lastselected device menu screen.
SEARCHING FOR YOUR CODE
If your device does not respond after trying all codes listed for your brand, or
if your brand is not listed at all, try searching for your code. For example, to
search for a code for your TV:.
NOTE: Before performing a code search for a CD or
DVD player or a VCR, turn on the device and insert
the required media
1.
Press and hold SETUP until the two bottom IR
segments flash twice. The Program Keys appear
as SETUP flashes repeatedly.
2.
Press SEARCH once.The Search Codes programming screen appears:
3.
Press a device key once (e.g., TV). The
selected device key animates.The
device’s Main Menu screen appears
with the HOME key still displayed.
4.
Press POWER once to select it as the
search test function.The Search
Programming screen appears again.
NOTE: With POWER as the search test
function, a “Power On” IR command is
sent to the device each time a test code is
sent.As a confirmation, the IR segments
display an outgoing animation.
NOTE: If your device or its original remote control does not have a Power key,
select a different test function in this step (e.g., CH+, VOL+, Play, etc.).
5.
Aim the remote control at the device (e.g., TV) and press one or more
times. Stop when a working code performs the test function selected in
step 4. If desired, use to try a previous code.
NOTE: In the search mode, the remote control sends IR codes from its
library to the selected device, starting with the most popular code first.
Searching For Your Code
19
OFA Kameleon wRF UG rev 3.fm Page 20 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
6.
To lock the code, press OK once.The two bottom IR segments flash twice.
7.
To search for codes of your other devices, repeat steps 3 to 6.
8.
To exit programming, press HOME twice. The display returns to the lastselected device menu screen.
CHECKING THE CODES
If you have set up the remote control using the Searching For Your Code
procedure (on the left), you may need to find out which code is operating
your equipment. For example, to find out which code is operating your TV:
1.
Press and hold SETUP until the two bottom IR
segments flash twice. The Program Keys
appear as SETUP flashes repeatedly.
2.
Press OTHER once.The Other programming screen appears:
3.
Using the Number Keys, enter 9 9 0.
The bottom two IR segments flash
twice.
4.
Press a device key once (i.e., AUX, CBL/
SAT, CD, TV, DVD, AUDIO, VCR, or PVR).
The selected device key animates.
5.
To view the code for the first digit, press
1 once.Count the number of times the
two bottom IR segments flash (e.g.,
three flashes = 3) and write down the
number in leftmost box in the TV code
boxes on page 17.
NOTE: If a code digit is “0”, the two
bottom IR segments do not flash.
6.
Repeat step 5 three more times for remaining digits.Use 2 for the second
digit, 3 for the third digit, and 4 for the fourth digit.Write down the code
digits in the remaining TV code boxes on page 17.
20
Checking The Codes
OFA Kameleon wRF UG rev 3.fm Page 21 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
NOTE: If you enter an invalid number (e.g., 7) or key (e.g., Play), the
two bottom IR segments display one long flash and return to the
“Other” programming screen. Start again with step 2 above.
7.
To check for codes of other devices, repeat steps 4 to 6, but substitute the
appropriate device key for each device you are checking. Write down the
device’s code digits in the appropriate code boxes on page 17.
8.
To exit programming, press HOME twice. The display returns to the lastselected device menu screen.
USING THE HOME THEATER MODE
The OFA Kameleon 8-Device Remote with RF includes a custom Home
Theater mode.After the Home Theater key is programmed, it allows you to
access four groups of remote control keys without having to change device
modes.
CONTROL ORGANIZATION
For Home Theater programming, the remote control’s keys are grouped by
type of control into the following four control groups:
Video Playback:
Transport Controls (Rewind, Play, Fast Forward, Stop,
Pause, Record, Skip Forward, Skip Back), and LIVE
TV
Volume Controls:
VOL+, VOL-, and MUTE
Channel Controls:
CH+, CH-, INPUT, Keypad (0 - 9), FAV, ENTER, LAST
Menu Controls:
Cursor Controls (Up, Down, Left, Right), OK, PAGE+,
PAGE-, MENU, INFO, GUIDE, EXIT
Moreover, the above Control Groups can be used in the following modes:
Video Playback:
AUDIO, AUX, CBL/SAT, CD, DVD, PVR, VCR
Volume Controls:
AUDIO, AUX, CBL/SAT, CD, DVD, PVR, TV, VCR
Channel Controls:
AUX, CBL/SAT, DVD, PVR, TV, and VCR
Menu Controls:
AUDIO, AUX, CBL/SAT, CD, DVD, PVR, TV, and VCR
Using The Home Theater Mode
21
OFA Kameleon wRF UG rev 3.fm Page 22 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
FACTORY DEFAULT SETTINGS
At the factory, the Control Groups are assigned the following modes as default
settings:
Video Playback:
DVD
Volume Controls:
AUDIO
Channel Controls:
CBL/SAT
Menu Controls:
CBL/SAT
If the default settings fit your needs,
you can skip programming this mode.
Otherwise, perform the steps in the
following section to assign device
modes to the Control Groups.
PROGRAMMING THE HOME THEATER MODE
1.
Press any device key once (i.e., AUX, CBL/SAT, CD, TV, DVD, AUDIO, VCR,
or PVR). The selected device key animates.
2.
Press and hold SETUP until the two bottom IR
segments flash twice. The Program Keys appear
as SETUP flashes repeatedly.
3.
Press THEATER once.The Video Playback programming screen appears:
NOTE: If a device key is animated, it is
assigned to this function group. To continue
programming the Home Theater mode, you
must select a device key, even if it is the same
one that is currently animated.
22
Using The Home Theater Mode
OFA Kameleon wRF UG rev 3.fm Page 23 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
4.
To assign a mode to the Video Playback group, press a device key once
(i.e., AUX, CBL/SAT, CD, TV, DVD, AUDIO, VCR, or PVR).Then the Volume
Controls programming screen appears:
NOTE: . If a device key is animated, it is
assigned to this function group. To continue
programming the Home Theater mode, you
must select a device key, even if it is the same
one that is currently animated.
5.
To assign a mode to the Volume Controls group, press a device key
once.Then the Channel Controls programming screen appears:
NOTE: . If a device key is animated, it is
assigned to this function group. To continue
programming the Home Theater mode, you
must select a device key, even if it is the same
one that is currently animated.
Using The Home Theater Mode
23
OFA Kameleon wRF UG rev 3.fm Page 24 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
6.
To assign a mode to the Channel Controls group, press a device key
once.Then the Menu Controls programming screen appears:
NOTE: If a device key is animated, it is
assigned to this function group. To
continue programming the Home
Theater mode, you must select a device
key, even if it is the same one that is
currently animated.
7.
To assign a mode to the Menu Controls
group, press a device key once. Since
Home Theater programming is now
complete, the Program Keys appear
again.
8.
To exit programming, press HOME
once.The display returns to the lastselected device menu screen.
USING THE IR/RF BASE STATION
The OFA Kameleon 8-Device Remote with RF (URC-9964B00) comes with an
IR/RF Base Station which receives radio-frequency (RF) signals from the
OFA Kameleon 8 Device Remote with RF, anywhere in your home, up to 100
feet away. Once it is set up, the IR/RF Base Station will convert the RF signals
into Infrared (IR) signals to control your home theater devices.
NOTE: The OFA Kameleon 8-Device Remote with RF transmits both an IR and
an RF signal simultaneously. It is your option whether you want to install the
IR/RF Base Station for extended remote control range. If you choose to do so,
during testing do not aim the OFA Kameleon 8-Device Remote with RF at your
home entertainment devices to verify that RF transmission is working.
NOTE: The RF signal transmitted by the OFA Kameleon 8-Device Remote with
RF, only works with the IR/RF Command Center.
SETTING UP THE IR/RF BASE STATION
1.
24
Find a location approximately 8 feet in front of your home theater
devices. It should provide (line-of-sight) access to your equipment and
a power outlet to plug in the IR/RF Base Station.
Using the IR/RF Base Station
OFA Kameleon wRF UG rev 3.fm Page 25 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
2.
Plug in the IR/RF Base Station's power
cord to the base station and to the wall
plug, as shown in the image to the right:
Power Cord
3.
Position the IR/RF Base Station so the black
IR Lens is aimed at your home theater
devices, as shown to the right:
4.
To test the IR/RF Base Station, take the OFA
Kameleon 8-Device Remote with RF into
another room in your home or up to 100
feet away in an open range. Select a device
key (e.g., TV) and press it once.Then press
POWER once. The device (e.g., TV) should
turn on.
Antenna
IR Lens
If it does not turn on, review the steps 1 through 3 and make any
adjustments. Try step 4 again. If you continue to have a problem, perhaps
there is an IR line-of sight problem. Try adding the enclosed IR Signal
Extension Cord (see“Adding the IR Signal Extension Cord” on page 25). Also
review the tips in “Optimizing IR/RF Base Station Reception” on page 27.
ADDING THE IR SIGNAL EXTENSION CORD
Included with the OFA Kameleon 8-Device Remote with RF package is an IR
Signal Extension Cord for use with a home theater device that is not in direct
line-of-sight of the IR/RF Base Station.
Using the IR/RF Base Station
25
OFA Kameleon wRF UG rev 3.fm Page 26 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
If you are having problems remotely controlling a home theater device from
another room, try the following:
1.
Plug the 4-foot IR Signal Extension Cord into the back of the IR/RF Base
Station.
2.
Run the IR Signal Extension Cord to the device that is not in line-ofsight of the IR/RF Base Station.
3.
Using the supplied double-sided tape, attach the IR Signal Extension
Cord so that its LED is in direct sight of the IR sensor of your home
theater device.
4.
Test the installation by again taking the OFA Kameleon 8-Device
Remote with RF into another room in your home, or up to 100 feet*
away in an open range. Select a device key (e.g., TV) and press it once.
Then press POWER once.
The IR/RF Command Center will convert the RF signal from the OFA
Kameleon 8-Device Remote with RF into an IR signal and transmit that
signal through the IR Signal Extension Cord to turn on your device (e.g., TV).
If it does not turn on, try repositioning the LED until the device can be
controlled, then re-attach the LED.
* Distance may vary
26
Using the IR/RF Base Station
OFA Kameleon wRF UG rev 3.fm Page 27 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
OPTIMIZING IR/RF BASE STATION RECEPTION
Here are some adjustment tips for optimizing the operation of your IR/RF
Base Station:
•
Aim the OFA Kameleon 8-Device Remote with RF toward the room
where the IR/RF Base Station is located.
•
Do not position the IR/RF Base Station near metal objects, such as heat
ducts. Metal can absorb RF signals.
•
Make sure the batteries in the OFA Kameleon 8-Device Remote with RF
are fully charged. Try replacing them if you are not sure (see “Installing
Batteries” on page 4). Weak batteries will affect the signal range.
•
Make sure that the OFA Kameleon 8-Device Remote with RF is not being
affected by other RF transmissions (e.g., garage door openers, cordless
telephones, etc.).
NOTE: The tests for range limits of the OFA Kameleon 8-Device Remote with RF
and the IR/RF Base Station were conducted in open-air distance tests. Actual
signal distance will be based on the construction of the building the unit is
being used in, as well as other factors, such as outside interference.
CHANGING VOLUME LOCK
The OFA Kameleon 8-Device Remote with RF is set at the factory for
independent volume control of each selected device.
However, you may change the Volume Lock setting to Global Volume Lock
so that a device’s volume is locked to one mode (e.g., to control TV volume in
all other modes). After that you can perform Individual Volume Unlock on a
selected device to set its volume control for independent operation.
LOCKING VOLUME CONTROL TO ONE MODE (GLOBAL VOLUME LOCK)
1.
Press and hold SETUP until the two bottom IR
segments flash twice. The Program Keys
appear as SETUP flashes repeatedly.
Changing Volume Lock
27
OFA Kameleon wRF UG rev 3.fm Page 28 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
2.
Press VOL once.The Volume Lock programming screen appears:
3.
Press a device key once (i.e., AUX, CBL/
SAT, CD, TV, DVD, AUDIO, VCR, or PVR)
where you want the volume controls
locked to.The two bottom IR segments
flash twice and the Program Keys
appears again.
4.
To exit programming, press HOME
once.The display returns to the lastselected device menu screen.
5.
Now, when you press VOL , VOL , or
MUTE, the selected device’s volume is
controlled, regardless of the mode
selected.
UNLOCKING VOLUME CONTROL FOR A SINGLE DEVICE
(INDIVIDUAL VOLUME UNLOCK)
1.
Press and hold SETUP until the two bottom IR
segments flash twice. The Program Keys
appear as SETUP flashes repeatedly.
2.
Press VOL once.The Volume Lock programming screen appears:
3.
Press VOL once. Press a device key
once (i.e., AUX, CBL/SAT, CD, TV, DVD,
AUDIO, VCR, or PVR) where you want
the volume controls unlocked.The two
bottom IR segments flash four times
and the Program Keys appear again.
NOTE: The programming mode is still
active as denoted by the flashing SETUP
key. If desired, use the other Program
Keys to continue programming (see Table
of Contents on page 2 for related
sections).
28
Changing Volume Lock
OFA Kameleon wRF UG rev 3.fm Page 29 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
4.
If desired, repeat steps 2 through 3 (of this section) for each device that
you want volume to be unlocked.
5.
To exit programming, press HOME once.The display returns to the lastselected device menu screen.
6.
Now, after you select a device that has volume unlocked, pressing
VOL , VOL , or MUTE controls the device’s volume only in its own
mode.
UNLOCKING ALL VOLUME CONTROL (RESTORING DEFAULT SETTING)
1.
Press and hold SETUP until the two bottom IR
segments flash twice. The Program Keys
appear as SETUP flashes repeatedly:
2.
Press VOL once.The Volume Lock programming screen appears:
3.
Press VOL once.The two bottom IR
segments flash four times and the
Program Keys appear again.
4.
To exit programming, press HOME
once.The display returns to the lastselected device menu screen.
5.
Volume is again independently
controlled according to its default states
for all programmed devices.
USING MACROS
The OFA Kameleon 8-Device Remote with RF includes five Macro Keys, M1
through M4 and POWER. Each one can be set up to perform a repetitive, timeconsuming operation with the press of a single key.
NOTE: . A macro programmed onto the POWER key can only be accessed in the
HOME THEATER mode. Pressing it in any other mode only sends a “Power On/
Off” IR command to the selected device.
Using Macros
29
OFA Kameleon wRF UG rev 3.fm Page 30 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
A macro can be used to control a home theater operation, to set a favorite
channel, or for other multiple functions you would like to control with one
key press. Moreover, each Macro Key can hold up to 15 key presses total.
NOTE: Programming a new macro over an existing one erases the original.
PROGRAMMING A FAVORITE CHANNEL MACRO
With so many channels available on your cable or satellite system, you can
program a macro that directly selects a favorite channel with one key press.
For example, let’s assume your favorite cable programs are on channel 71.
Use the following instructions to program a macro for direct access of this
channel:
NOTE: . The following example assumes all equipment is turned off and that the
TV is connected through the Cable Box with TV tuning set to channel 3.
1.
Press and hold SETUP until the two bottom IR
segments flash twice. The Program Keys
appear as SETUP flashes repeatedly.
2.
Press MACRO once.The Macro programming screen appears:
3.
Press an open Macro Key
(e.g.,M1,M2,M3, or M4). The lastselected device menu screen, including
HOME, appears.
4.
Enter a macro sequence of up to 15 key
presses. For this example, press TV
once, followed by POWER once, and
then enter 0 3 for the TV’s channel
number. Next, press CBL/SAT once,
followed by POWER once, and then enter
0 7 1 for the Cable Box’s channel
number.
NOTE: If there are more than 15 key presses in the sequence, the bottom
IR segments display a long flash denoting an error. The display returns to
the last-selected device menu screen. To program the macro, start again
with step 3.
30
Using Macros
OFA Kameleon wRF UG rev 3.fm Page 31 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
5.
To save the macro, press and hold SETUP until the two bottom IR
segments flash twice. The Program Keys appear again.
6.
Exit programming by pressing HOME once. The display returns to the
last-selected device menu screen.
7.
Now, if you aim the remote control at the devices selected in step 4 and
press the programmed Macro Key once, the TV turns on and tunes to
channel 3. Then the Cable Box turns on and tunes to channel 071.
PROGRAMMING A MASTER POWER MACRO IN THE HOME THEATER MODE
A macro can be programmed onto the POWER key to turn on or off as many
as seven Home Theater devices.
NOTE: This following example assumes the Home Theater system contains a
Satellite Receiver, a DVD Player, an Audio Receiver, and a TV.
1.
Press and hold SETUP until the two bottom IR
segments flash twice. The Program Keys
appear as SETUP flashes repeatedly.
2.
Press MACRO once.The Macro programming screen appears:
3.
Press POWER once.The last-selected
device menu screen, including HOME,
appears.
4.
Enter the macro sequence. For this
example, press CBL/SAT once, followed
by POWER once. Next, press DVD once,
followed by POWER once.Then press
AUDIO once, followed by POWER once.
Finally, press TV once, followed by
POWER once.
5.
To save the power macro, press and hold SETUP until the two bottom IR
segments flash twice. The Program Keys appear again.
6.
Exit programming by pressing HOME once. The display returns to the
last-selected device menu screen.
7.
To test the power macro, first make sure all home theater devices
selected in step 4 are turned on. Aim the remote control at the devices
Using Macros
31
OFA Kameleon wRF UG rev 3.fm Page 32 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
and press the Home Theater key once, followed by POWER once.The
devices should turn off in this order: Satellite Receiver, DVD Player,
Audio Receiver, and TV.
To turn on the devices on again in the same order as above, press
POWER once.
CLEARING A MACRO
1.
Press and hold SETUP until the two bottom IR
segments flash twice. The Program Keys
appear as SETUP flashes repeatedly.
2.
Press MACRO once.The Macro programming screen appears:
3.
Select the Macro Key to be cleared and
press it once.The last-selected device
menu screen appears.
4.
Press and hold SETUP until the two
bottom IR segments flash twice. The
Program Keys appear again.
5.
To exit programming, press HOME
once.The display returns to the lastselected device menu screen.
USING LEARNING
The OFA Kameleon 8-Device Remote with RF includes a Learning feature so
you can add functions that are unique to your home entertainment devices
(e.g.,VCR Tracking Up or Down).However, there are some considerations:
LEARNING PRECAUTIONS
•
Your original remote controls must be in working order for learning to
work properly.
•
Learned keys are mode specific, so each one can store a unique function
for each mode.
•
Learned keys can be used in macros (see Using Macros on page 29).
32
Using Learning
OFA Kameleon wRF UG rev 3.fm Page 33 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
•
Do not use the following keys for learning: Device Keys, M1~M4, SETUP,
FAV, SCROLL, PRESET, PVR VOD, or Record (•) Key.
•
Learning capacity is approximately 50 to 75 keys, depending on the code
being learned.
•
If both learned and keymoved functions are assigned to the same key, the
last programmed function is stored.
•
A learned function cannot be used as a source for Keymover (see Using
Keymover on page 36).
•
Certain device codes are not learnable including multi-frequency types,
some high frequency ones, and other unusual formats.
•
For optimum learning, avoid high levels of ambient light such as natural
sunlight or energy-efficient fluorescent lights.
NOTE: . Please have your original remote controls handy before programming
learning. Be sure to press each teaching key within 5 seconds of the previous entry.
Otherwise, the OFA Kameleon 8-Device Remote with RF exits programming mode.
PROGRAMMING A LEARNING KEY
1.
Press and hold SETUP until the two bottom IR
segments flash twice. The Program Keys appear as
SETUP flashes repeatedly.
2.
Press IR LRN once.The IR Learn programming screen appears:
3.
Using Learning
Press a device key once (i.e., AUX, CBL/SAT,
CD, TV, DVD, AUDIO, VCR, or PVR) to assign
a mode for learning.The selected device
menu screen, including HOME, appears.
33
OFA Kameleon wRF UG rev 3.fm Page 34 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
4.
Place the OFA Kameleon 8-Device Remote with RF head-to-head (about
2" apart) from your original remote control. Also locate the key (on your
original remote control) that will serve as the teaching function.
2"
5.
On the OFA Kameleon 8-Device Remote with RF, select and press a key
where the learned function will be stored.The IR segments display an
incoming animation, continue for three revolutions, and then the entire
display turns off.
After the display is off, press and hold the teaching key (on your original
remote control) until the display (on the OFA Kameleon 8-Device
Remote) turns on again.The two bottom IR segments flash twice when
the code is successfully captured.
NOTE: If the two bottom IR segments display one long flash, a learning
error has occurred.Try repeating this step again until a successful capture
occurs. If the function is still not captured, press HOME twice to
exit programming and review the “Learning Precautions” on the previous
page. If needed, also see “Troubleshooting” on page 54.After review, start
programming again at step 1.
6.
To learn other functions, repeat steps 3 through 5 as desired.
7.
To exit programming, press HOME twice. The display returns to the lastselected device menu screen.
DELETING A SINGLE LEARNING KEY
1.
34
Press and hold SETUP until the two bottom IR
segments flash twice. The Program Keys
appear as SETUP flashes repeatedly.
Using Learning
OFA Kameleon wRF UG rev 3.fm Page 35 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
2.
Press IR DEL once.The IR Delete programming screen appears:
3.
Press a device key once (i.e., AUX, CBL/
SAT, CD, TV, DVD, AUDIO, VCR, or PVR)
for the mode where the learned key to
be deleted resides. The selected device
menu screen, including HOME, appears.
4.
Press the learned key to be deleted
twice. Upon deletion, the two bottom IR
segments flash twice as confirmation.
The Program Keys appear again.
6.
If desired, repeat steps 2 through 4 to delete another learned key.
7.
Exit programming by pressing HOME once. The display returns to the
last-selected device menu screen.
DELETING ALL LEARNED KEYS IN A SPECIFIC MODE.
1.
Press and hold SETUP until the two bottom IR
segments flash twice. The Program Keys
appear as SETUP flashes repeatedly
2.
Press IR DEL once.The IR Delete programming screen appears:
3.
Press a device key once (i.e.,AUX, CBL/
SAT,CD, TV,DVD, AUDIO, VCR, or PVR)
for the mode where the learned keys to
be deleted reside. The selected device
menu screen, including HOME, appears.
4.
Press the same device key (as in step 3) once. Upon deletion, the two
bottom IR segments flash twice as confirmation.The Program Keys
appear again.
5.
If desired, repeat steps 2 through 4 to delete other learned keys from
another mode.
6.
Exit programming by pressing HOME once. The display returns to the
last-selected device menu screen.
Using Learning
35
OFA Kameleon wRF UG rev 3.fm Page 36 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
REASSIGNING DEVICE KEYS
The OFA Kameleon 8-Device Remote with RF can be set to control a second
device. For example, to control a TV, a cable box, and two DVD players, you
can reassign the unused AUX key to operate the second DVD player as follows:
1.
Press and hold SETUP until the two bottom IR
segments flash twice. The Program Keys
appear as SETUP flashes repeatedly
2.
Press MODE once.The Mode Mover programming screen appears:
3.
For the source mode, press a device key
once (i.e., AUX, CBL/SAT, CD, TV, DVD,
AUDIO, VCR, or PVR). For this example,
press DVD once. The selected device
menu screen, including HOME, appears.
NOTE: Only one device can be assigned
to an unused device key at a time.
4.
For the destination mode, press a device key once (i.e., AUX, CBL/SAT,
CD, TV, DVD, AUDIO, VCR, or PVR). For this example, press AUX
once.Upon reassignment, the two bottom IR segments flash twice as
confirmation. The Program Keys appear again.
5.
For this example, the AUX key is now ready to be set up to control your
second DVD player. See Programming Device Control on page 15. If
desired, repeat steps 2 to 4 to reassign another device.
6.
Exit programming by pressing HOME once. The display returns to the
last-selected device menu screen.
USING KEYMOVER
The OFA Kameleon 8-Device Remote with RF includes a Keymover feature
that allows you to map (or copy) keys from one mode (i.e., source mode) to
another mode (i.e., destination mode).
NOTE: Do not use any of the Device Keys as a source or destination key.
Also, do not use POWER as a destination key.
36
Reassigning Device Keys
OFA Kameleon wRF UG rev 3.fm Page 37 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
PROGRAMMING KEYMOVER
For example, if your DVD player does not have volume control, you can map
those keys (i.e., VOL , VOL , and MUTE) from the TV mode to DVD mode:
1.
Press and hold SETUP until the two bottom IR
segments flash twice. The Program Keys
appear as SETUP flashes repeatedly
2.
Press OTHER once. The Other programming screen appears:
3.
Using the Number Keys, enter 9 9 4. The
two bottom IR segments flash twice.
4.
For the source mode, press a device key
once (i.e., AUX, CD, etc.). For this
example, press TV once. The source device
menu screen, including HOME, appears.
5.
For the source key, press a key to be moved
once. For this example press VOL once.
6.
For the destination mode, press a device
key once (i.e., AUX, CBL/SAT, CD, TV, DVD,
AUDIO, VCR, or PVR). For this example,
press DVD once. The selected destination
device menu screen, including HOME,
appears.
7.
For the destination key, press a key to be moved once. For this example
press VOL
once.Upon keymoving, the two bottom IR segments
flash twice as confirmation. The Program Keys appear again.
8.
Repeat steps 2 through 7 two more times to map the remaining volume
control keys, substituting VOL and MUTE as source and destination
keys in steps 5 and 7.
9.
Exit programming by pressing HOME once. The display returns to the
last-selected device menu screen.
You can now use your OFA Kameleon 8-Device Remote with RF to control the
TV’s volume and mute in the DVD mode, as well as in the TV mode.
Using Keymover
37
OFA Kameleon wRF UG rev 3.fm Page 38 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
RESTORING A SINGLE KEYMOVED KEY
1.
Press and hold SETUP until the two bottom IR
segments flash twice. The Program Keys
appear as SETUP flashes repeatedly
2.
Press the destination mode once where the keymoved key is stored.
Then press OTHER once. The Other programming screen appears:
3.
Using the Number Keys, enter 9 9 4.The
two bottom IR segments flash twice.
4.
Press the destination mode once where
the keymoved key is stored.Then press
the destination key twice.Upon key
restoration, the two bottom IR
segments flash twice as
confirmation.The Program Keys appear
again.
5.
If desired, repeat steps 1 and 2 to restore
another key.
6.
Exit programming by pressing HOME
once. The display returns to the lastselected device menu screen.
RESTORING ALL KEYMOVED KEYS IN A SINGLE MODE
1.
Perform steps 1 through 3 of Programming Keymover, above.
2.
Press the destination mode twice where the keymoved keys are stored.
Upon key restoration, the two bottom IR segments flash twice as
confirmation. The Program Keys appear again.
3.
Exit programming by pressing HOME once. The display returns to the
last-selected device menu screen.
38
Using Keymover
OFA Kameleon wRF UG rev 3.fm Page 39 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
USING CHANNEL SCAN
In the AUX, CBL/SAT, or TV mode, use the FAV key to start a 3-second scan of
all channels. If programmed, use the FAV key to scan only your favorite
channels to view a channel (see Programming Favorite Channel Scan below).
1.
Press AUX, CBL/SAT, or TV once.The two bottom IR segments flash once.
2.
Press FAV once.The IR segments display outgoing animation as each
channel is changed.
3.
•
If Favorite Channel Scan has been set up, scanning of favorite
channels starts and cycles through stored channels for 3 minutes
or until stopped by pressing any key.
•
If Favorite Channel Scan has not been set up, scanning starts with
the current channel, then proceeds to the next channel up and
cycles through all channels for 3 minutes or until stopped by
pressing any key.
To stop scanning channels at any time, press any key once.
PROGRAMMING FAVORITE CHANNEL SCAN
In the AUX, CBL/SAT, or TV mode, you can store a list of up to 10 favorite
channels, in any order, that are immediately scanned when FAV is pressed
(see Using Channel Scan above).
NOTE: . Favorite channels can only be programmed for one mode. After
programming, if FAV is pressed while in another mode, the remote control starts
a normal channel scan instead (if applicable to the selected device).
1.
Press and hold SETUP until the two bottom IR
segments flash twice. The Program Keys
appear as SETUP flashes repeatedly
2.
Select a Favorite Channel Mode by pressing AUX, CBL/SAT, or TV
once.The two bottom IR segments flash once as the selected device key
animates.
Using Channel Scan
39
OFA Kameleon wRF UG rev 3.fm Page 40 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
3.
Press OTHER once.The Other programming screen appears:
4.
Using the Number Keys, enter 9 9 6.
The two bottom IR segments flash
twice and display the Favorite Channel
programming screen.
NOTE: If the two bottom IR segments
display one long flash, an error has
occurred. Try repeating this step.
5.
Using the Number Keys, enter a favorite
channel number (e.g., 0 1 2). Then
press SETUP once.The two bottom IR
segments flash three times confirming
your entry.
NOTE: If the original remote control required pressing an Enter key to
change the channel, also press the ENTER key after the channel number
(e.g., 0 1 2 ENTER).
6.
If desired, repeat step 5 for each channel to be stored, up to a total of 10
channels.
NOTE: After storing 10 channels, the remote control exits the Favorite
Channel programming screen and again displays the Program Keys.
7.
To exit programming with fewer than 10 favorite channels stored, press
and hold SETUP until the two bottom IR segments flash twice and then
press HOME once.The display returns to the last-selected device menu
screen.
RESTORING FACTORY DEFAULT SETTINGS
The OFA Kameleon 8-Device Remote with RF includes an Setup Code
Reset program.You can use it to restore all your programmed codes to
factory settings and delete all custom programming.
IMPORTANT: Executing this program erases all code settings and all
custom settings for Home Theater, Macros, Learned Keys, Reassigned
Device Keys, Keymoved Keys, Favorite Channels, and all device settings.
40
Restoring Factory Default Settings
OFA Kameleon wRF UG rev 3.fm Page 41 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
1.
Press and hold SETUP until the two bottom IR
segments flash twice. The Program Keys
appear as SETUP flashes repeatedly
2.
Press OTHER once.The Other programming screen appears:
3.
Using the Number Keys, enter 9 7 7. The
two bottom IR segments flash twice
pause and flash twice again to confirm
the unit has been restored to factory
default settings.
4.
Exit programming by pressing HOME
once. The display returns to the lastselected device menu screen.
CLEARING ALL CUSTOM PROGRAMMING
The OFA Kameleon 8-Device Remote with RF contains a Custom
Programming Reset program.You can use it to remove all custom
programming, except your setup codes and reassigned device keys.
IMPORTANT: Executing this program erases all custom settings for Home
Theater, Macros, Learned Keys, Keymoved Keys, and Favorite Channels.
1.
Press and hold SETUP until the two bottom IR
segments flash twice. The Program Keys
appear as SETUP flashes repeatedly
Clearing All Custom Programming
41
OFA Kameleon wRF UG rev 3.fm Page 42 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
2.
Press OTHER once.The Other programming screen appears:
3.
Using the Number Keys, enter 9 8
0.The two bottom IR segments flash
twice pause and flash twice again to
confirm the unit has been restored to
factory default settings.
4.
Exit programming by pressing HOME
once. The display returns to the lastselected device menu screen.
MANUFACTURER’S CODES
SETUP CODES FOR AUDIO
AMPLIFIERS
GE
JVC
Optimus
Realistic
Soundesign
Victor
Wards
Yamaha
0078
0331
0395
0395
0078
0331
0078
0354
SETUP CODES FOR AUDIO
RECEIVERS
ADC
Aiwa
Alco
Anam
Apex Digital
Audiotronic
42
0531
0158, 0189, 1388,
0121, 1089
1390
1609
1257
1189
Audiovox
Bose
Capetronic
Carver
Coby
Curtis
Denon
Fisher
Glory Horse
Harman/Kardon
Integra
JBL
JVC
Kenwood
KLH
Koss
Linn
Magnavox
1390
1229
0531
1189, 0189, 1089
1263, 1389
1263
1360
1409
1263
0110, 0189
1298, 0135
0110, 1306
0074, 1263, 1374
1313, 1570, 1569,
1027, 0186
1390
1366
0189
1189, 1269, 0189,
1089, 0531
Manufacturer’s Codes
OFA Kameleon wRF UG rev 3.fm Page 43 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
Marantz
MCS
Musicmagic
Norcent
Onkyo
Optimus
Oritron
Panasonic
Philips
Pioneer
Polk Audio
Proscan
Quasar
RadioShack
RCA
Samsung
Sansui
Sharp
Sharper Image
Sony
Soundesign
Stereophonics
Sunfire
Teac
Technics
Thorens
Venturer
Victor
Wards
Yamaha
1189, 1269, 0039,
0189, 1089
0039
1089
1389
1298, 0842, 0135
1023, 0670, 0531,
0186, 0797
1380, 1366
1518, 0039
1189, 1269, 0189,
1089
1023, 0531, 1384,
0150, 0014, 0630
0189
1254
0039
1263
1023, 1609, 1254,
0531, 1390
1295
0189, 1089
0186
1416, 1549, 1385,
1411, 1546, 1723,
1263, 1410,1545,
1556, 0797, 1409
1058, 1258, 0158,
1758, 1158, 1658,
1558
0670
1023
1313
1390
1308, 1518, 0039
1189
1390
0074
0158, 0189, 0014
0176, 1176, 0186,
1375
Manufacturer’s Codes
SETUP CODES FOR CABLE BOXES
ABC
Americast
Bell & Howell
Bell South
Director
General Instrument
GoldStar
Hamlin
Jerrold
Memorex
Motorola
Pace
Panasonic
Paragon
Philips
Pioneer
Pulsar
Quasar
Regal
Runco
Samsung
Scientific Atlanta
Sony
Starcom
Supercable
Torx
Toshiba
Zenith
0003, 0008, 0014
0899
0014
0899
0476
0476, 0276, 0003
0144
0009, 0273
0476, 0276, 0003,
0014
0000
0476, 0276
0237
0000, 0107
0000
0305, 0317
0877, 1877, 0144,
0533
0000
0000
0279, 0273
0000
0144
0877, 1877, 0477,
0008
1006
0003
0276
0003
0000
0000, 0525, 0899
SETUP CODES FOR CD PLAYERS
Aiwa
0157
Burmester
0420
California Audio Labs 0029
Carver
0157
Denon
0873
DKK
0000
DMX Electronics
0157
Garrard
0420
43
OFA Kameleon wRF UG rev 3.fm Page 44 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
Genexxa
Harman/Kardon
Hitachi
JVC
Kenwood
KLH
Krell
Linn
Magnavox
Marantz
MCS
Miro
Mission
MTC
NSM
Onkyo
Optimus
Panasonic
Parasound
Philips
Pioneer
Polk Audio
Proton
QED
Quad
Quasar
RCA
Realistic
Rotel
SAE
Sansui
Sharp
Sonic Frontiers
Sony
TAG McLaren
Tascam
TDK
Teac
Technics
Victor
Wards
44
0032
0157
0032
0072
0681, 0626, 0028
1318
0157
0157
0157
0626, 0029, 0157
0029
0000
0157
0420
0157
0868
1063, 0000, 0032,
0420
0029
0420
0626, 0157
1063, 1062, 0032
0157
0157
0157
0157
0029
1062, 0032, 0420
0420
0157, 0420
0157
0157
0861
0157
0490, 0000, 0100
0157
0420
1208
0420
0029
0072
0157
Yamaha
Zonda
0888, 0036, 1292
0157
SETUP CODES FOR DVD PLAYERS
Aiwa
Allegro
AMW
Apex Digital
Blaupunkt
Blue Parade
Broksonic
CineVision
Daewoo
Denon
DVD2000
Emerson
Enterprise
Fisher
Funai
GE
Go Video
Greenhill
Harman/Kardon
Hitachi
Hiteker
Initial
Integra
JBL
JVC
Kenwood
KLH
Koss
Lasonic
Magnavox
Marantz
Memorex
Microsoft
Mintek
Mitsubishi
Nesa
0641
0869
0872
0672, 0717, 0755,
0796, 1100, 0795,
0830, 0794,0797
0717
0571
0868, 0695
0876, 0869
0784
0490, 0634
0521
0591, 0821, 0675
0591
0670
0675
0522, 0815, 0717
0744, 0715, 0783
0717
0702, 0582
0573, 0664
0672
0717
0627
0702
0558, 0623, 0867
0490, 0534, 0682
0717
0651
0798
0503, 0675
0539
0695
0522
0717
1521, 0521
0717
Manufacturer’s Codes
OFA Kameleon wRF UG rev 3.fm Page 45 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
Norcent
Onkyo
Oritron
Panasonic
Philips
Pioneer
Polk Audio
Proscan
Qwestar
RCA
Rio
Rotel
Sampo
Samsung
Sansui
Sanyo
Sharp
Sharper Image
Sherwood
Shinsonic
Sonic Blue
Sony
Sylvania
Symphonic
Technics
Theta Digital
Toshiba
Tredex
Urban Concepts
Xbox
Yamaha
Zenith
0872
0503, 0627
0651
0490, 0632, 1490,
1462, 1362, 1762
0503, 0539, 0646,
0854
0525, 0571, 0632
0539
0522
0651
0522, 0571, 0717,
0822
0869
0623
0698
0490, 0573, 0820
0695
0873, 0695, 0670
0630, 0752
1117, 1112, 1995
0633
0533
0869
0533, 0864
0821, 0675
0675
0490
0571
0503, 0695, 1045
0799
0503
0522
0490, 0539, 0545,
0817
0503, 0591, 0869
SETUP CODES FOR DVD PLAYER/
PVR COMBOS
Panasonic
RCA
0490
0522
Manufacturer’s Codes
SETUP CODES FOR DVD PLAYER/
VCR COMBOS (DVD CODES)
Allegro
CineVision
Go Video
Hitachi
JVC
Memorex
Panasonic
RCA
Samsung
Sansui
Sanyo
Sharp
Sony
Sylvania
Symphonic
Toshiba
Zenith
0869
0869
0744, 0715
0664
0867
0695
1762
0822
0820
0695
0873
0630
0864
0675
0675
0503
0869
SETUP CODES FOR DVD PLAYER/
VCR COMBOS (VCR CODES)
Hitachi
RCA
Sanyo
Sharp
Sylvania
Symphonic
0000
0060
0104
0848
0000
0000
SETUP CODES FOR HOME
AUTOMATION
GE
Lasko
One For All
RadioShack
Security System
Sharper Image
Universal X10
X10
0240
0846
0167
0240
0167
0846
0167
0167
45
OFA Kameleon wRF UG rev 3.fm Page 46 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
SETUP CODES FOR HOME-THEATERIN-A-BOX SYSTEMS (RECEIVER
CODES)
Aiwa
Anam
Apex Digital
Audiovox
Coby
Integra
JBL
JVC
KLH
Koss
Norcent
Onkyo
Oritron
Philips
Pioneer
Polk Audio
RCA
Rio
Samsung
Sharper Image
Sony
Teac
Venturer
Yamaha
1388
1609
1257
1390
1389
1298
1306
1374
1390
1366
1389
0135, 1298, 0842
1366
1269
1384
0539
1609, 1390
0869
1295
1556
1558, 1758, 1658
1390
1390
1375
SETUP CODES FOR HOME-THEATERIN-A-BOX SYSTEMS (DVD CODES)
Aiwa
Koss
Onkyo
Oritron
Polk Audio
Rio
Sharper Image
Sonic Blue
Yamaha
46
0641
0651
0627
0651
0539
0869
1995
0869
0817
SETUP CODES FOR MINI-DISC
PLAYERS
Denon
Kenwood
Onkyo
Optimus
Pioneer
Sharp
Sony
Yamaha
0873
0681
0868
1063
1063
0861
0490
0888
SETUP CODES FOR PVRS
Panasonic
Philips
ReplayTV
Sonic Blue
Sony
Tivo
0616
0618
0614, 0616
0616, 0614
0636
0739, 0636, 0618
SETUP CODES FOR SATELLITE
RECEIVERS
AlphaStar
Chaparral
Crossdigital
DirecTV
0772
0216
1109
0392, 0566, 0639,
1639, 1142, 0247,
0749, 1749,0724,
0819, 1856, 1076,
1109, 1442, 1392
Dish Network System 1005, 0775
Dishpro
1005, 0775
Echostar
1005, 0775
Expressvu
0775
GE
0566
General Instrument 0869
GOI
0775
Hitachi
0819
HTS
0775
Hughes Network
1142, 0749, 1749,
Systems
1442
JVC
0775
Magnavox
0724, 0722
Manufacturer’s Codes
OFA Kameleon wRF UG rev 3.fm Page 47 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
Memorex
Mitsubishi
Motorola
Next Level
Panasonic
Paysat
Philips
Proscan
RadioShack
RCA
Samsung
SKY
Sony
Star Choice
Tivo
Toshiba
UltimateTV
Uniden
Voom
Zenith
0724
0749
0869
0869
0247, 0701
0724
1142, 0749, 1749,
0724, 1076, 0722,
1442
0392, 0566
0869
0392, 0566, 0855,
0143, 1392
1276, 1109
0856
0639, 1639
0869
1142, 1442
0749, 1749, 0790
1392
0724, 0722
0869
0856, 1856
SETUP CODES FOR SATELLITE
RECEIVERS/PVR COMBOS
Echostar
Expressvu
Hughes Network
Systems
Philips
Proscan
RCA
Sony
1005, 0775
0775
1142, 1442
1142, 1442
0392
1392
0639
SETUP CODES FOR TVS
Admiral
Advent
Aiko
Aiwa
Akai
0093, 0463
0761, 0842
0092
0701
0812, 0702, 0030,
0672
Manufacturer’s Codes
Alaron
Albatron
America Action
Ampro
Anam
AOC
Apex Digital
Audiovox
Bell & Howell
Bradford
Broksonic
Candle
Carnivale
Carver
Celebrity
Celera
Changhong
Citizen
Clarion
Concerto
Contec
Craig
Crosley
Crown
Curtis Mathes
CXC
Daewoo
Denon
Dumont
Durabrand
Dwin
Electroband
Elektra
0179
0843
0180
0751
0180
0030
0748, 0765, 0767
0451, 0180, 0092,
0623
0154, 0016
0180
0236, 0463
0030, 0056
0030
0054
0000
0765
0765
0060, 0030, 0092,
0056
0180
0056
0180
0180
0054
0180
0047, 0054, 0154,
0451, 0093, 0060,
0702, 0030,0145,
0166, 1147, 0016,
0466, 1347, 0056
0180
0451, 0092, 0672,
0623
0145
0017
0180, 0178, 0171,
0463
0774, 0720
0000
0017
47
OFA Kameleon wRF UG rev 3.fm Page 48 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
Emerson
Envision
Epson
Fisher
Fujitsu
Funai
Futuretech
GE
Gibralter
GoldStar
Grunpy
Hallmark
Harley Davidson
Harman/Kardon
Harvard
Havermy
Hello Kitty
Himitsu
Hisense
Hitachi
Hyundai
Infinity
Inteq
JBL
JCB
Jensen
JVC
KEC
Kenwood
KLH
Konka
KTV
LG
Logik
Luxman
LXI
48
0154, 0236, 0463,
0180, 0178, 0171,
0623, 0179
0030
0840, 0833
0154
0809, 0683, 0179,
0853
0180, 0171, 0179
0180
0047, 0051, 0451,
0178, 0021, 1347,
1147
0017, 0030
0030, 0178
0180, 0179
0178
0179
0054
0180
0093
0451
0180
0748
1145, 0145, 0056,
0016
0849
0054
0017
0054
0000
0761
0053
0180
0030
0765, 0767
0707
0180, 0030
0856
0016
0056
0047, 0054, 0154,
0156, 0178
Magnavox
Majestic
Marantz
Matsushita
Megatron
Memorex
MGA
Midland
Minutz
Mitsubishi
Monivision
Motorola
MTC
Multitech
NAD
NEC
Nikko
Norcent
NTC
Onwa
Optimus
Optonica
Orion
Panasonic
Penney
Philco
Philips
Pilot
Pioneer
Portland
Prima
Prism
Proscan
Proton
Pulsar
Quasar
0054, 0030, 1454,
0706, 1254, 0179
0016
0054, 0030, 0704
0250, 0650
0178, 0145
0154, 0463, 0150,
0178, 0016, 0179
0150, 0030, 0178
0047, 0017, 0051
0021
0093, 0150, 0178,
0836
0843
0093
0060, 0030, 0056
0180
0156, 0178, 0866
0030, 0497, 0056
0030, 0178, 0092
0748, 0824
0092
0180
0154, 0250, 0166,
0650
0093
0236, 0463, 0179
0250, 0051, 0650
0047, 0156, 0051,
0060, 0030, 0178,
1347, 0021
0054, 0030
0054, 1454, 0690
0030
0166, 0866, 0679
0092
0761
0051
0047, 1347, 1447
0178, 0466
0017
0250, 0051, 0650
Manufacturer’s Codes
OFA Kameleon wRF UG rev 3.fm Page 49 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
RadioShack
RCA
Realistic
Runco
Sampo
Samsung
Sansui
Sanyo
Scotch
Scott
Sears
Sharp
Sharper Image
Sheng Chia
Signature
Sony
Soundesign
Squareview
SSS
Starlite
Supreme
SVA
Sylvania
Symphonic
Tandy
Technics
Technol Ace
Techwood
Teknika
Telefunken
0047, 0154, 0180,
0030, 0178, 0056
0047, 1447, 1047,
1347, 0679, 1247,
0090, 1147
0154, 0180, 0030,
0178, 0056
0017, 0030, 0603,
0497
0030
0060, 0812, 0702,
0030, 0178, 0056,
0814, 0766,1060
0463
0154, 0799
0178
0236, 0180, 0178,
0179
0047, 0054, 0154,
0156, 0178, 0171,
0056, 0179
0093, 0688, 0851,
0491, 0818, 0689
1950
0093
0016
1100, 0000, 0834,
0810
0180, 0178, 0179
0171
0180
0180
0000
0748
0054, 0030, 0171
0180, 0171
0093
0250, 0051
0179
0051, 0056
0054, 0180, 0150,
0060, 0056, 0092,
0016, 0179
0702, 0056
Manufacturer’s Codes
TMK
TNCi
Toshiba
0178, 0056
0017
0154, 0156, 0060,
1256, 0845, 0832,
1356, 0650
TVS
0463
Vector Research
0030
Victor
0053
Vidikron
0054
Vidtech
0178
Wards
0054, 0030, 0178,
0021, 0056, 0866,
0016, 0179
Waycon
0156
White Westinghouse 0463, 0623
Yamaha
0030, 0833, 0769
Zenith
0017, 0463, 0178,
0016, 0092
SETUP CODES FOR TV/DVD
PLAYER COMBOS (TV CODES)
Sylvania
0675
SETUP CODES FOR TV/DVD
PLAYER COMBOS (DVD CODES)
Apex Digital
Broksonic
Panasonic
Philips
Sylvania
Toshiba
0830
0695
1490
0854
0171
0695
SETUP CODES FOR TV/VCR
COMBOS (TV CODES)
America Action
Audiovox
Emerson
0180
0180
0236
49
OFA Kameleon wRF UG rev 3.fm Page 50 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
SETUP CODES FOR TV/VCR
COMBOS (VCR CODES)
SETUP CODES FOR TV/VCR/DVD
PLAYER COMBOS
America Action
Audiovox
Broksonic
Citizen
Curtis Mathes
Daewoo
Emerson
Broksonic
Emerson
Panasonic
Sharp
Sylvania
Toshiba
Funai
GE
GoldStar
Harley Davidson
Hitachi
Lloyd's
Magnasonic
Magnavox
Magnin
Memorex
MGA
Optimus
Orion
Panasonic
Penney
Philco
Quasar
RadioShack
RCA
Sansui
Sanyo
Sears
Sony
Sylvania
Symphonic
Thomas
Toshiba
Zenith
50
0278
0278
0002, 1479, 0479
1278
1035
1278
0002, 1479, 1278,
0479
0000
0240, 1035, 1060
1237
0000
0000
0000
1278
0000, 1781
0240
0162, 1237, 1162
0240
1162
0002, 0479, 1479
0162, 1162, 1035
0240, 1237, 1035
0479
0162, 1035, 1162
0000
0240, 1060, 1035
0000, 1479, 0479
0240
0000, 1237
0000, 1232
1781
0000
0000
0845
0000, 0479, 1479
0868
0821
1362, 1462
0630
0821
1045
SETUP CODES FOR VCRS
Admiral
Adventura
Aiko
Aiwa
America Action
American High
Asha
Audiovox
Beaumark
Bell & Howell
Broksonic
Calix
Canon
Carver
CCE
Citizen
Craig
Curtis Mathes
Cybernex
Daewoo
Denon
Durabrand
Dynatech
Electrohome
Electrophonic
Emerex
Emerson
0048, 0209
0000
0278
0037, 0000
0278
0035
0240
0037, 0278
0240
0104
0184, 0121, 0209,
0002, 0479, 1479
0037
0035
0081
0278
0037, 0278, 1278
0037, 0047, 0240
0060, 0035, 0162,
1035
0240
0045, 0278, 1278
0042
0039
0000
0037
0037
0032
0037, 0184, 0000,
0121, 0043, 0209,
0002, 0278,1479,
1278, 0479
Manufacturer’s Codes
OFA Kameleon wRF UG rev 3.fm Page 51 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
Fisher
Fuji
Funai
Garrard
GE
Go Video
GoldStar
Gradiente
Harley Davidson
Harman/Kardon
HI-Q
Hitachi
Hughes Network
Systems
JVC
KEC
Kenwood
Kodak
Lloyd's
LXI
Magnasonic
Magnavox
Magnin
Marantz
Marta
Matsushita
MEI
Memorex
MGA
MGN Technology
Minolta
Mitsubishi
Motorola
MTC
Multitech
NEC
Nikko
0047, 0104
0035, 0033
0000
0000
0060, 0035, 0240,
1035, 1060
0432
0037, 1237
0000
0000
0081
0047
0000, 0042
0042
0067
0037, 0278
0067
0035, 0037
0000
0037
1278
0035, 0039, 0081,
0000, 1781
0240
0035, 0081
0037
0035, 0162, 1162
0035
0035, 0162, 0037,
0048, 0039, 0047,
0240, 0000,0104,
0209, 1162, 0479,
1237
0240, 0043
0240
0042
0067, 0043
0035, 0048
0240, 0000
0000
0104, 0067
0037
Manufacturer’s Codes
Noblex
Olympus
Optimus
Orion
Panasonic
Penney
Pentax
Philco
Philips
Pilot
Pioneer
Polk Audio
Profitronic
Proscan
Pulsar
Quasar
RadioShack
Radix
Randex
RCA
Realistic
Runco
Samsung
Sanky
Sansui
Sanyo
Scott
Sears
Sharp
Shogun
Sony
0240
0035
0162, 0037, 0048,
0104, 0432, 1162
0184, 0209, 0002,
1479, 0479
0035, 0162, 1035,
0225, 1162
0035, 0037, 0240,
0042, 1035, 1237
0042
0035, 0479
0035, 0081, 1081,
1181
0037
0067
0081
0240
0060, 1060
0039
0035, 0162, 1162,
1035
0000
0037
0037
0060, 0240, 0042,
0880, 1060, 1035
0035, 0037, 0048,
0047, 0000, 0104
0039
0240, 0045
0048, 0039
0000, 0067, 0209,
1479, 0479
0047, 0240, 0104
0184, 0045, 0121,
0043
0035, 0037, 0047,
0000, 0042, 0104,
1237
0048, 0848
0240
0035, 0032, 0033,
0000, 1232
51
OFA Kameleon wRF UG rev 3.fm Page 52 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
STS
Sylvania
0042
0035, 0081, 0000,
0043, 1781
Symphonic
0000
Teac
0000
Technics
0035, 0162
Teknika
0035, 0037, 0000
Thomas
0000
TMK
0240
Toshiba
0045, 0043, 0845
Totevision
0037, 0240
Unitech
0240
Vector
0045
Video Concepts
0045
Videomagic
0037
Videosonic
0240
Villain
0000
Wards
0060, 0035, 0048,
0047, 0081, 0240,
0000, 0042
White Westinghouse 0209
XR-1000
Zenith
0035, 0000
0039, 0033, 0000,
0209, 1479, 0479
SETUP CODES FOR VIDEO
ACCESSORIES
Panasonic
Pioneer
Princeton
Sensory Science
Sharp
1120
1010
0113, 0295
1126
1010
SETUP CODES FOR CABLE/DVR
COMBOS
Motorola
Pioneer
Scientific Atlanta
0476
1877
1877
ABOUT UPGRADING
Your OFA Kameleon 8-Device Remote with RF has the largest infrared code
library available and contains a unique feature that allows new codes to be
added to its memory over the phone. In a matter of seconds, your OFA
Kameleon 8-Device Remote with RF can quickly and reliably record the new
information without complex plugs, adapters, or attachments.
This means that as you buy new products in the future, the OFA Kameleon
8-Device Remote with RF will never become obsolete. Simply call our consumer
help-line, and one of our customer service representatives will assist you through
the entire process of upgrading your OFA Kameleon 8-Device Remote with RF.
Consumer Help-Line: (330) 405-8620
NOTE: Universal Electronics reserves the right to replace a returned remotecontrol with a new one of equal or superior functionality.
52
About Upgrading
OFA Kameleon wRF UG rev 3.fm Page 53 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
UPGRADE PROCEDURE
1.
Call our Consumer Help-Line at: (330) 405-8620 on any business day,
between 9 AM and 5:30 PM, EST.
2.
Our customer service agent will ask for and record the brand name(s)
and model number(s) of your device(s). Then the agent will lead you
through the upgrade procedure by asking you to place your telephone’s
speaker next to the CH keys on the OFA Kameleon 8-Device Remote (as
shown below).
NOTE: Only use a land-line phone for the upgrade
procedure. Do not use a mobile phone because it
will not transmit the signals correctly.
In a matter of seconds, new setup codes for your device(s) will be
transmitted through the telephone and stored in your OFA Kameleon
8-Device Remote with RF.
3.
After your OFA Kameleon 8-Device Remote with RF has been
successfully upgraded by telephone, stay on the line.Our customer
service agent will ensure that your unit is working properly with your
device(s) and answer any other questions you may have.
UPGRADE EXCLUSIONS
•
Home entertainment or home automation devices controlled by radio
frequency (RF/UHF), wired, or ultrasonic remotecontrols. Only devices
controlled by infrared remote controls are covered.
•
Home entertainment or home automation devices not controlled by
remote controls.
•
Broken or defective product.
•
Products that operate over 100 kHz.
•
Infrared keyboards a nd infrared pointing devices (such as mouse
substitutes).
•
All products for sale and/or use outside the continental United States,
Hawaii, Alaska, or Canada.
About Upgrading
53
OFA Kameleon wRF UG rev 3.fm Page 54 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
TROUBLESHOOTING
PROBLEM:
No display at all times.
SOLUTION:
Replace batteries with four new AA alkaline batteries.
PROBLEM:
The bottom two IR indicator segments are flashing.
SOLUTION:
Replace batteries with four new AA alkaline batteries.
PROBLEM:
No display when programming.
SOLUTION:
Display has turned off due to inactivity. Start programming
again and do not pause while performing instructions.
PROBLEM:
During programming, the two bottom IR segments display
a long flash.
SOLUTION:
An invalid entry has occurred. Check the keys to be pressed
and start program again.
PROBLEM:
How do I stop programming?
SOLUTION:
Press HOME once to return to the Program Keys screen.
Press HOME once more to exit completely.
PROBLEM:
The unit does not control home entertainment devices or
commands are not working properly.
SOLUTION:
Try all listed codes for the device brands being set up.Make
sure they can be operated with an infrared remote control.
PROBLEM:
Tried Searching For Your Code method and still could not
find a working code.
SOLUTION:
Perform Restoring Factory Default Settings on page 40. Then
repeat Searching For Your Code on page 19.
PROBLEM:
Cannot program a macro onto M1 – M4 or POWER keys.
SOLUTION:
Make sure the total number of key presses being
programmed is less than 15.
PROBLEM:
Power macro does not execute.
SOLUTION:
First, press the Home Theater key once, then press POWER
once.
54
Troubleshooting
OFA Kameleon wRF UG rev 3.fm Page 55 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
PROBLEM:
Favorite channel function does not work properly.
SOLUTION:
Some devices (e.g.,Cable Boxes or Satellite Receivers) use
two-digit channel numbers. During programming, press
ENTER or OK once after entering a channel number (e.g., 0 2
ENTER for channel 2). See Programming Favorite Channel
Scan on page 39.
PROBLEM:
Changing channels does not work properly.
SOLUTION:
If the original remote control required pressing ENTER to
change channels, then press ENTER on the remote control
after entering channel numbers.
PROBLEM:
No remote control of volume.
SOLUTION:
See Changing Volume Lock on page 27 to lock/unlock
volume.
PROBLEM:
Two bottom IR segments flash when a key is pressed, but
home entertainment device does not respond.
SOLUTION:
Make sure the remote control is aimed at your home
entertainment device and is not farther than 15 feet away.
PROBLEM:
CH
SOLUTION:
Due to RCA design (1983-1987), only the original remote
control will operate these functions.
PROBLEM:
Pressing SCROLL one or times in CD, DVD, PVR or Home
Theater mode, does not display a secondary menu screen.
SOLUTION:
Even though SCROLL is displayed, for these modes, there are
no additional menu screens.
PROBLEM:
Cannot program my combo device code.
SOLUTION:
Make sure have selected the correct device key for your
combo code.
Troubleshooting
and CH do not work for your RCA TV.
55
OFA Kameleon wRF UG rev 3.fm Page 56 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
DEVICE MENU SCREENS
PROGRAMMING MAIN MENU
AUDIO MAIN MENU
Pressing and holding SETUP
displays the Programming Main
Menu screen.Use the Program Keys
to program device control (DEV
SET), code search (SEARCH), home
theater mode (THEATER), volume
lock (VOL), macros (MACRO),
display brightness ( ),function
learning (IR LRN and IR DEL),
device key reassignment (MODE), or
other functions (OTHER).See the
Table of Contents on page 2 to locate
a section of interest.
Pressing AUDIO once displays the
AUDIO Main Menu screen.After
device programming, use these keys
to remotely control your Audio
Receiver’s or Amplifier’s volume and
stations, select source inputs,
operate transport functions on a
built-in CD player (or DVD player, if
HTIB device), and access menu,
surround, or preset functions.
56
Pressing SCROLL one or more times
displays secondary AUDIO menus
(see next two pages).
Device Menu Screens
OFA Kameleon wRF UG rev 3.fm Page 57 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
AUDIO SURROUND MENU
Pressing SCROLL once (on the
AUDIO Main Menu, as shown on the
previous page, right side) displays
the AUDIO Surround Menu
screen.Use these keys to remotely
control your Audio Receiver’s or
Amplifier’s volume, stations, and
surround functions.
Device Menu Screens
AUDIO MENU
Pressing SCROLL once (on the
AUDIO Surround Menu, as shown
on the left) displays the AUDIO
Menu screen.Use these keys to
remotely control your Audio
Receiver’s or Amplifier’s volume,
stations, and surround functions.
57
OFA Kameleon wRF UG rev 3.fm Page 58 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
AUDIO PRESETS MENU
AUX MAIN MENU
Pressing SCROLL once (on the
AUDIO Menu, as shown on the
previous page, right side), displays
the AUDIO Presets Menu screen.Use
these keys to remotely access your
Audio Receiver’s or Amplifier’s
preset stations.
Pressing AUX once displays the AUX
Main Menu screen.After device
programming, use these keys to
remotely control all your device’s
common features, such as volume
and channels, and menu, guide, and
navigation functions.
Pressing SCROLL once more returns
the display to the AUDIO Main
Menu screen (as shown on page 56,
right side).
Pressing SCROLL once displays a
secondary AUX menu (on shown on
the next page, left side).
58
Device Menu Screens
OFA Kameleon wRF UG rev 3.fm Page 59 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
AUX PVR/VOD MENU
CBL/SAT MAIN MENU
Pressing SCROLL once (on the AUX
Main Menu, as shown on previous
page, right side) displays the AUX
PVR/VOD Menu screen.Use these
keys to remotely control all your
device’s VOD and PVR functions,
such as transport keys, replay, and
live TV.
Pressing CBL/SAT once displays the
CBL/SAT Main Menu screen. After
Cable Box or Satellite Receiver
programming, use these keys to
remotely control all common
features, such as volume and
channels, and menu, guide, and
navigation functions.
Pressing SCROLL once more returns
the display to the AUX Main Menu
screen (as shown on the previous
page, right side).
Pressing SCROLL once displays a
secondary CBL/SAT menu (on
shown on the next page, left side).
Device Menu Screens
59
OFA Kameleon wRF UG rev 3.fm Page 60 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
CBL/SAT PVR/VOD MENU
CD MAIN MENU
Pressing SCROLL once (on the CBL/
SAT Main Menu, as shown on
previous page, right side) displays
the CBL/SAT PVR/VOD Menu
screen.Use these keys to remotely
control all your device’s VOD and
PVR functions, such as transport
keys, replay, and live TV.
Pressing CD once displays the CD
Main Menu screen.After device
programming, use these keys to
remotely control all your CD player’s
common features, such as transport
keys and skip, menu, and random
functions.
Pressing SCROLL once more returns
the display to the CBL/SAT Main
Menu screen (as shown on the
previous page, right side).
60
Device Menu Screens
OFA Kameleon wRF UG rev 3.fm Page 61 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
DVD MAIN MENU
Pressing DVD once displays the DVD
Main Menu screen.After device
programming, use these keys to
remotely control all your DVD
player’s common features, such as
transport keys and menu,
navigation, subtitle, and audio
functions.
Device Menu Screens
HOME THEATER MAIN MENU
After mode programming, pressing
Home Theater once displays the
Home Theater Main Menu screen.
Use these keys to remotely access all
common features and functions of
your home theater system. For
details, see Using The Home Theater
Mode on page 21.
61
OFA Kameleon wRF UG rev 3.fm Page 62 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
PVR MAIN MENU
Pressing PVR once displays the PVR
Main Menu screen.After device
programming, use these keys to
remotely control all your PVR’s (or
DVR’s) common features, such as
transport keys and menu, guide,
navigation, replay, and live TV
functions.
62
TV MAIN MENU
Pressing TV once displays the TV
Main Menu screen.After device
programming, use these keys to
remotely control all your TV’s
common features, such as volume
and channels, and last channel,
menu, and information/display
functions. Pressing SCROLL one or
more times displays secondary TV
menus (see the next page).
Device Menu Screens
OFA Kameleon wRF UG rev 3.fm Page 63 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
TV MENU
Pressing SCROLL once (on the TV
Main Menu, as shown on previous
page, right side) displays the TV
Menu screen.Use these keys to
remotely control all your TV’s
common menu features.
TV PIP MENU
Pressing SCROLL once (on the TV
Menu, as shown on the left)
displays the TV PIP Menu
screen.Use these keys to remotely
control all your TV’s common PIP
features.
Pressing SCROLL once more returns
the display to the TV Main Menu
screen (as shown on the previous
page, right side).
Device Menu Screens
63
OFA Kameleon wRF UG rev 3.fm Page 64 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
VCR MAIN MENU
VCR MENU
Pressing VCR once displays the VCR
Main Menu screen.After device
programming, use these keys to
remotely control all your TV’s
common features, such as volume
and channels, and last channel,
menu, and information/display
functions. Pressing SCROLL once
displays a secondary VCR menu (on
the right).
Pressing SCROLL once (on the VCR
Main Menu, as shown on the left)
displays the VCR Menu screen. Use
these keys to remotely control all
your VCR’s common features.
64
Pressing SCROLL once more returns
the display to the VCR Main Menu
screen (as shown on the left).
Device Menu Screens
OFA Kameleon wRF UG rev 3.fm Page 65 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
CUSTOMER SUPPORT
could void the user's authority to operate his
equipment.
For assistance, please contact us in
any of the following ways:
FCC Authorization Label
•
E-mail:
[email protected]
•
Internet: http://
www.oneforall.com
•
Consumer Help-Line: (330)
405-8620
COMPLIANCE WITH FCC
RULES AND REGULATIONS
This equipment has been tested and found to
comply with the limits for a class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.This
equipment generates, uses and radiates radio
frequency energy and if not installed and
used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or
television reception, which can be
determined by turning the equipment off and
on, the user is encouraged to try and correct
the interference by one or more of the
following measures:
•
Reorient or relocate the receiver
antenna.
•
Increase the separation between the
equipment and the receiver.
•
Connect the equipment into an outlet
that is different from that to which the
receiver is connected.
•
Consult the dealer or an experienced
radio/television technician for help.
The user is cautioned that changes and
modifications made to the equipment
without the approval of the manufacturer
Customer Support
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
1.
This device may not cause harmful
interference and
2.
This device must accept any
interference received, including
interference that may cause undesired
operation.
FCC ID #: MG3UR9964
OFA Kameleon 8-Device Remote with RF
Command Center: (FCC Image)
IC Authorization Label
IC:2575-UR9966
The term “IC:2575-UR9966” before the
certification/registration number only
signifies that the Industry Canada technical
specifications were met.
LIMITED WARRANTY
Universal Electronics warrants, to the
original purchaser only, that this product will
be free from defects in materials and
workmanship, under normal use, for ninety
(90) days from the date of original purchase.
This limited warranty is valid only on
Universal Electronics product purchased and
used in the United States of America or
Canada, and does not apply to products used
for industrial or commercial purpose.
The limited warranty does not cover damage
or failure caused by products or services not
supplied by Universal Electronics, or which
result from accident, misuse, abuse, neglect,
mishandling, misapplication, faulty
installation, set-up adjustment, improper
maintenance, alteration, maladjustment of
consumer controls, modifications,
commercial use, or that is attributable to acts
of God.
There are no express warranties except as
listed above.Universal Electronics SHALL
NOT BE LIABLE FOR INCIDENTAL OR
65
OFA Kameleon wRF UG rev 3.fm Page 66 Monday, September 13, 2004 11:18 AM
KAMELEON 8-DEVICE REMOTE WITH RF
CONSEQUENTIAL DAMAGES RESULTING
FROM THE USE OF THIS PRODUCT OR
ARISING OUT OF ANY BREACH OF
WARRANTY.ALL EXPRESS AND IMPLIED
WARRANTIES, INCLUDING THE
WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR
PURPOSE,ARE LIMITED TO THE
WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion or
limitation of incidental or consequential
damages, or limitations on how long an
implied warranty lasts, so the above
exclusions or limitations may not apply to
you. This warranty gives you specific legal
rights and you may also have other rights
which vary from state to state.
To obtain warranty service for a defective
product during the warranty period, please
return the product, preferably in the original
carton, along with your purchase receipt, to
the store of original purchase.A note detailing
the complaint would be helpful.The store, at
its option, will replace or repair this product
if found to be defective.
For warranty information only, call: (330)
405-8655
BATTERY USE AND SAFETY
•
Dispose of old batteries promptly and properly.
•
Do not burn or bury batteries.
•
Use only new batteries of the required size.
•
Do not mix old and new batteries, different types of batteries (e.g.,
standard, alkaline, or rechargeable), or rechargeable batteries of
different capacities.
•
If you do not plan to use the remote control for an extended period,
remove the batteries. They can leak chemicals that can destroy
electronic parts.
•
If you’re using rechargeable batteries, we recommend using a NiMH
type with a capacity of 550 mAhr or more.
ABOUT BATTERY LIFE
As with all battery-operated devices, battery life will vary depending on use,
including frequency and duration of key presses on the Kameleon screen.
Battery life may be extended by performing some or all of the following:
•
Reducing the brightness level of the display screen (see “Adjusting
Brightness” on page 13).
•
Reducing the on time of the display screen (see “Adjusting How Long
The Screen Light is On” on page 14).
66
Battery Use And Safety
OFA Kameleon wRF UG rev 3.fm Page 67 Monday, September 13, 2004 11:18 AM
USER’S GUIDE
•
Disabling the vibration switch (see “Setting the Vibration Switch” on
page 15).
The two bottom IR indicator segments will flash when the batteries in your
Kameleon are running low.
SPECIFICATIONS
Remote Control Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 AAA Batteries
IR/RF Base Station Power Cord Power . . . . . . . . . . . . . . . . . . 120 V DC 200mA
Remote Control to IR/RF Base Station Range . . . . . up to 100 Feet (30.48 m)*
IR/RF Base Station to Device Range . . . . . . . . . . . . . . . 25 Feet (7.62 m) ± 30°
* Distance may vary
Remote Control Dimensions
(H x W x D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4/16 x 2-10/16 x 1 in.
(H x W x D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235 x 67 x 26 mm
IR/RF Base Station Dimensions
(H x W x D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1/8 x 3-1/8 x 3 in
(H x W x D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 x 80 x 76 mm
Remote Control Weight (without Batteries). . . . . . . . . . . . . . . . . .5.6 oz (159 g)
IR/RF Base Station Weight (Without Power Adapter) . . . . . . . . . .2.4 oz (68 g)
NOTE: Specifications are typical. Individual units might vary. Specifications
are subject to change and improvement without notice.
ADDITIONAL INFORMATION
Kameleon is a trademark of Universal Electronics.
Copyright 2004 by Universal Electronics. No part of this publication may be
reproduced, transmitted, transcribed, stored in any retrieval system, or
translated to any language, in any form or by any means, electronic,
mechanical, magnetic, optical, manual, or otherwise, without the prior
written permission of Universal Electronics Inc.
The OFA Kameleon 8-Device Remote with RF (URC-9964B00) is compatible
for use in North America, excluding Mexico.
URC-9964B00
Specifications
4/04
67
OFA Kameleon wRF UG rev 3.fm Page 68 Monday, September 13, 2004 11:18 AM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement