advertisement
EXP-2000
SPX Expansion interface!
modules
The EXP-2000 provides additional Door/Panel interface points to most SPX products. The EXP-2000 uses a local
RS-485 network through an SPX gateway device. Additional access points can be added as needed.
""
""
EXP-2000"
Part 15 Class A
EXP-2000_MAN_0314
"
Electrical and Mechanical Specifications
Physical
Temp
Humidity
Power
Data I/O
Aluminum Enclosure 3.5" x 2.75" x .75" each unit
Storage(-55˚C to + 150˚C)"
Operating(-40˚C to +80˚C)
95% (non-condensing)
Input
Output
Interface
Unreg Input 8 to 16 VDC
*
@ 200mA Max
+5VDC @100mA
Reader 0- 30VDC"
LED - 0 - 30VDC"
Analog 0 - 5 VDC"
*
See Rating Curve for Temperature and Power ratings
3.3”
ø 0.15”
2.8”
DataBender CVX-1300
1.4”
Unit Height = 0.75”
3.65”
External Dimensions and Mounting Holes
This complies with part 15 of the FCC rules
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Cypress Computer Systems, Inc. ⌖ Lapeer, MI 48446 ⌖ www.cypressintegration.com
© 2014 Cypress Computer Systems Inc.
"
EXP-1000 Operation Compatibility
" EXP-2000 Compatibility with Cypress Suprex Systems!
The EXP-2000 modules are designed to provide additional reader interface channels to some systems utilizing
" Cypress Suprex devices. Not all Cypress Suprex systems support the use of the EXP-1000 modules. "
The EXP-2000 is a product enhancement that has been added to the Suprex product line."
" EXP-2000 modules may not be compatible with Suprex products that were purchased prior to May of 2010. "
"" The following listing indicates which systems support the addition of EXP-1000 modules."
" The EXP-2000 is compatible with current versions of the following Cypress Products:!
" SPX-7400/10 Fiber Optic Suprex - Multi-mode or single mode"
" SPX-7200 Lan Network Suprex"
" SPX-5521 RF Suprex 900Mhz"
" SPX-5601 RF Suprex 2.4 GHz"
" SPX-5621 RF Suprex 2.4 GHz"
"" SPX-7500 RS-485 Suprex"
" Products not specifically listed are not compatible with the EXP-2000 module."
"
"
"
"
"
"
"
"
"
EXP-2000 Operation
"
"
SPX-7400, SPX-7500. SPX-5600, or SPX-7200 system. Each EXP-2000 can be set to a unique address (1 through 15, see DIP switch chart). "
EXP Units used with a Cypress Suprex Gateway device will be set to the same address on both the Central and Remote sides of the system."
SPX Systems:"
The EXP-2000 is used with Suprex Gateway devices (SPX-7400/10 (FO), SPX-7500 (485), SPX-5600 (RF), SPX-7200(ET)) to add Central and Remote pairs. "
EXP-2000 Setup:!
The DIP switch will be preset and labeled to determine whether the EXP-1000 will operate as a Wiegand Receiver (Remote) or
Wiegand Transmitter (Central). "
Initialization of the EXP-2000:"
1. Power off, Set DIP Switch #1 ON, All other DIP switches off"
Set DIP Switch #3 OFF if using EXP-2000 with Suprex systems"
"
"
2. Apply power to the EXP-2000."
The LED should illuminate with a solid Green indication."
3. Remove power and turn off all DIP Switches."
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
4. The unit is now initialized for usage with the appropriate system. Proceed to the following pages to set "
DIP switches for address and Wiegand direction."
" Setting EXP-2000 Addresses:!
"
"
"
"
"
"
"
"
When using the EXP-2000 units with a Suprex gateway system, the Addresses must be set consecutively from 1 to the maximum
"
"
"
"
"
"
"
"
"
"
" address to be used with the system. Most Suprex gateway systems will support a maximum of 8 devices"
(refer to Gateway manual)"
""
Example: An SPX-7400 system is to be setup with 4 pairs of EXP-2000 units."
The Addresses should be set: 1, 2, 3, 4 for the 4 pairs that will be used with the system and not 2,3,4,5 or 4,6,7,8 etc."
J1
J2
" J1 Connections"
2- 8 to 16 VDC In"
1- Ground
"
"
"
"
"
"
12-R4 N.O."
."
""
8-RS485 (+ )"
7-RS485 (-) "
6-+5 VDC Out "
5-prog res 2 " *
"
3-LED In "
2-Data 1 out "
1-Data 0 out
C
"
"
"
"
EXP-2000!
"
"
"
"
"
"
"
"
"
11-R4 Com"
10-R4 N.C"
9-R3 N.O."
8-R3 Com"
7-R3 N.C."
6-RS232 output"
5-RS232 Input"
J3 Connections"
4-Ground"
3-Aux out"
12 - Relay #4""
2-R2 in"
1-R1 in
2 - 8 to 16 VDC" Power IN (+)"
"
" 1 - Ground" " Power IN (-)"
J2 Connections"
8 - RS485 (+)"" RS-485 Input"
11 - Relay #4"" Common"
10 - Relay #4""
J3
"
7 - RS485 (-)" " RS-485 Input"
6 - +5 VDC OUT" 5 Volt Power out"
5 - Analog 2" " Analog Input #2"
4 - Analog 1 " " Analog Input #1"
3 - LED I/O" " LED Signal Input/Output"
2 - Data 1 Out" Wiegand Data 1 Output"
1 - Data 0 Out" Wiegand Data 0 Output "
1 2 3 4 5 6 7 8
On
"
Off
Address settings for the EXP-2000"
"
"
"
"
Cypress Suprex® systems will support different numbers number. Refer to the specific documents for the
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
9 - Relay #3" "
8 - Relay #3" "
7 - Relay #3" "
N.O. Contact"
N.C. Contact"
N.O. Contact"
Common"
N.C. Contact"
6 - RS232 Output" Serial Data OUT "
5 - RS232 Input" Serial Data IN "
4 - Ground" " Wiegand/RS232 Ground"
3 - Aux" " Digital Output"
2 - Relay # 2" " Digital Input"
1 - Relay # 1" " Digital Input"
"
SPX-7400, SPX-5600, or SPX-7200 for maximum ratings."
Note: "
"
"
"
"
"
"
To operate as a "Central" unit, DIP Switch #2 must be On."
"
"
"
"
"
"
"
DIP Switch Address Settings
"
" ADDRESS" "
" " "
1" " "
2" " "
3" " "
4" " "
5" " "
6" " "
7" " "
8" " "
9" " "
10" " "
11" " "
12" " "
13" " "
14" " "
15" " "
16" " "
SWITCH" "
12345678"
01000001"
01000010"
01000011"
01000100"
01000101"
01000110"
01000111"
01001000"
01001001"
01001010"
01001011"
01001100"
01001101"
01001110"
01001111" "
01010000
"
"
"
"
"
J1
J2
J1 Connections"
2 - 8 to 16 VDC"
2- 8 to 16 VDC In"
1- Ground
8-RS485 (+ )"
7-RS485 (-) "
6-+5 VDC Out "
5- R4 in " *
"
3-LED out "
2-Data 1 in "
1-Data 0 in
Power IN (+)"
" 1 - Ground" " Power IN (-) "
J2 Connections"
8 - RS485 (+)""
5 - Relay #4" "
4 - Relay # 3 "
2 - Data 1 In" "
1 - Data 0 In" "
EXP-2000 R Electrical Connections
RS-485 Input"
7 - RS485 (-)" " RS-485 Input"
6 - +5 VDC OUT" 5 Volt Power out"
Analog Input #4"
Analog Input #3"
3 - LED I/O" " LED Signal Output"
Wiegand Data 1 Input"
Wiegand Data 0 Input "
"
"
1 2 3 4 5 6 7 8
On
Off
"
"
"
"
" Address settings for the EXP-2000"
"
"
Cypress Suprex® systems will support different numbers number. Refer to the specific documents for the
"
"
" SPX-7400, SPX-5600, or SPX-7200 for maximum ratings."
Note: "
"
"
" "
"
"
"
"
"
"
"
"
"
"
"
"
"
R "
"
"
"
"
"
"
"
1 - Not used
."
12- R2 N.O."
11- R2 Com"
10- R2 N.C"
9- R1 N.O."
8- R1 Com"
7- R1 N.C."
6-RS232 output"
5-RS232 Input"
4-Ground"
3- Aux in"
2- Not used"
""
" J3 Connections"
"
"
12 - Relay #2""
"
"
11 - Relay #2"" Common"
J3
"
"
10 - Relay #2""
9 - Relay #1" "
"
"
8 - Relay #1" "
7 - Relay #1" "
6 - RS232 Output"
5 - RS232 Input"
4 - Ground" "
3 - Aux in" "
2 -" " "
Common"
"
Serial Data OUT "
"
"
Not used"
1 - " " " Not used
"
"
DIP Switch Address Settings
"
" ADDRESS" " SWITCH" "
" " " 12345678"
1" " " 00000001"
2" " " 00000010"
3" " " 00000011"
4" " " 00000100"
5" " " 00000101"
6" " " 00000110"
7" " " 00000111"
8" " " 00001000"
9" " " 00001001"
10" " " 00001010"
11" " " 00001011"
12" " " 00001100"
13" " " 00001101"
14" " " 00001110"
15" " " 00001111" "
16" " " 00010000
80
55
Ambient Temperature
(Degrees Celsius)
35
-40
"
"
"
"
"
"
"
"
"
"
"
"
8 10
"
"
"
"
"
"
"
"
"
"
"
"
12
Supply Voltage
14 16
"
"
Temperature/Voltage de-rating curve
"
"
"
"
Any voltage between 8 and 16 volts can be utilized by following the temperature /voltage derating curve. Voltage should not exceed 16 VDC under normal operating conditions. " "
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
SPX to EXP-2000 Connections
"
"
"
8- RS-485(+)"
5- Analog IN2"
4- Analog IN1"
3- LED I/O"
2- D1 I/O"
1- D0 I/O
8-RS485 (+ )"
7-RS485 (-) "
6-+5 VDC Out "
5-Analog 2 "
*
"
3-LED I/O "
2-Data 1 I/O "
1-Data 0 I/O
8-RS485 (+ )"
7-RS485 (-) "
6-+5 VDC Out "
5-Analog 2 "
*
"
3-LED I/O "
2-Data 1 I/O "
1-Data 0 I/O
SPX
7- RS-485 (-)"
6- +5VDC Out"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
CYPRESS
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
CYPRESS
"
"
"
"
"
"
"
"
"
"
Suprex Operation and Initial Setup
"
To activate the relay on the Remote unit connect as shown below. These connections can be used to allow the
Remote relay to operate a DOOR STRIKE, GATE, or other locking hardware. Refer to following pages in this document for details of each I/O operation and connection. The Relay inputs are active LOW and will activate the
" relay when connected to ground."
There are two relays available for accessory outputs at the Remote end. Either relay can be used to provide the Door
Strike or Gate activation function. This example uses Relay 1.
Access Control !
Panel
LED OUT
2-8 to 16 VDC In"
1-Ground
8-485(+)"
7-485(-)
"
6-+5 VDC Out"
5-Prog Res 2" *
3-LED Input"
2-D1/Data/F2F Out "
1-D0/Clock Out
Central Unit
12-RLY4 N.O."
11-RLY4 Com"
10-RLY4 N.C."
9-RLY3 N.O."
8-RLY3 Com"
7-RLY3 N.C."
6-RS232 Out"
5-RS232 In"
4-Ground"
3-Aux Out"
2-Relay2 Input"
1-Relay1 Input"
Typical Access Control Panel Connection to activate Door Strike and reader LED.
Strike follows LED
Only Relay and LED Connections are shown for clarity, refer to previous diagrams for
Power,Data and communications connections.
2-8 to 16 VDC In"
1-Ground
Access Control !
Panel
LED OUT"
STRIKE
"
8-485(+)"
7-485(-)
"
6-+5 VDC Out"
5-Prog Res 2" *
3-LED Input"
2-D1/Data/F2F Out "
1-D0/Clock Out
Central Unit
12-RLY4 N.O."
11-RLY4 Com"
10-RLY4 N.C."
9-RLY3 N.O."
8-RLY3 Com"
7-RLY3 N.C."
6-RS232 Out"
5-RS232 In"
4-Ground"
3-Aux Out"
2-Relay2 Input"
1-Relay1 Input"
Typical Access Control Panel Connection to activate Door Strike and reader LED. Strike follows separate panel output.
"
Suprex Operation and Initial Setup
I/O Controls
The Cypress EXP-2000 provides additional data channels to support access control hardware such as door strikes, tamper alarms, request to exit status, etc. These signals are sent to and from the Remote and Central units without
" the need to run additional wiring."
The accessory control I/O use active low inputs. When the inputs are floating (nothing connected) the associated output will be set to a high level. When the input is set to 0Volts (Ground) the input will activate its associated
" output. All Accessory outputs are Open Collector type and will switch to Ground when activated."
Each input will have an associated output. See the following pages for a diagram of each I/O pair."
Inputs can be tested by making a jumper connection to ground and monitoring the associated output.
Input
Output
2-8 to 16 VDC In"
1-Ground
8-485(+)"
7-485(-)
"
6-+5 VDC Out"
5-Prog Res 2" *
3-LED Input"
2-D1/Data/F2F Out "
1-D0/Clock Out
Central Unit
12-RLY4 N.O."
11-RLY4 Com"
10-RLY4 N.C."
9-RLY3 N.O."
8-RLY3 Com"
7-RLY3 N.C."
6-RS232 Out"
5-RS232 In"
4-Ground"
3-Aux Out"
2-Relay2 Input"
1-Relay1 Input"
Red arrow denotes direction!
of command signal
2-8 to 16 VDC In"
1-Ground
8-485(+)"
7-485(-)
"
6-+5 VDC Out"
5-RLY4 Input (5V)"
*
3-LED Output"
2-D1/Data/F2F Input"
1-D0/CLK Input
Remote Unit
12-RLY2 N.O."
11-RLY2 Com"
10-RLY2 N.C."
9-RLY1 N.O."
8-RLY1 Com"
7-RLY1 N.C."
6-RS232 Out"
5-RS232 In"
4-Ground"
3-Aux In"
2-N/C"
1-N/C"
I/O Controls
"
2-8 to 16 VDC In"
1-Ground
8-485(+)"
7-485(-)
"
6-+5 VDC Out"
5-Prog Res 2" *
3-LED Input"
2-D1/Data/F2F Out "
1-D0/Clock Out
Central Unit
12-RLY4 N.O."
11-RLY4 Com"
10-RLY4 N.C."
9-RLY3 N.O."
8-RLY3 Com"
7-RLY3 N.C."
6-RS232 Out"
5-RS232 In"
4-Ground"
3-Aux Out"
2-Relay2 Input"
1-Relay1 Input"
Red arrow denotes direction!
of command signal
Input
2-8 to 16 VDC In"
1-Ground
8-485(+)"
7-485(-)
"
6-+5 VDC Out"
5-RLY4 Input (5V)"
*
3-LED Output"
2-D1/Data/F2F Input"
1-D0/CLK Input
Remote Unit
12-RLY2 N.O."
11-RLY2 Com"
10-RLY2 N.C."
9-RLY1 N.O."
8-RLY1 Com"
7-RLY1 N.C."
6-RS232 Out"
5-RS232 In"
4-Ground"
3-Aux In"
2-N/C"
1-N/C"
Output
Relay 1 Input and Output
"
2-8 to 16 VDC In"
1-Ground
8-485(+)"
7-485(-)
"
6-+5 VDC Out"
5-Prog Res 2" *
3-LED Input"
2-D1/Data/F2F Out "
1-D0/Clock Out
Central Unit
12-RLY4 N.O."
11-RLY4 Com"
10-RLY4 N.C."
9-RLY3 N.O."
8-RLY3 Com"
7-RLY3 N.C."
6-RS232 Out"
5-RS232 In"
4-Ground"
3-Aux Out"
2-Relay2 Input"
1-Relay1 Input"
Input
Red arrow denotes direction!
of command signal
2-8 to 16 VDC In"
1-Ground
8-485(+)"
7-485(-)
"
6-+5 VDC Out"
5-RLY4 Input (5V)"
*
3-LED Output"
2-D1/Data/F2F Input"
1-D0/CLK Input
Remote Unit
12-RLY2 N.O."
11-RLY2 Com"
10-RLY2 N.C."
9-RLY1 N.O."
8-RLY1 Com"
7-RLY1 N.C."
6-RS232 Out"
5-RS232 In"
4-Ground"
3-Aux In"
2-N/C"
1-N/C"
Output
Relay 2 Input and Output
Suprex Operation and Initial Setup
"
2-8 to 16 VDC In"
1-Ground
8-485(+)"
7-485(-)
"
6-+5 VDC Out"
5-Prog Res 2" *
3-LED Input"
2-D1/Data/F2F Out "
1-D0/Clock Out
Central Unit
12-RLY4 N.O."
11-RLY4 Com"
10-RLY4 N.C."
9-RLY3 N.O."
8-RLY3 Com"
7-RLY3 N.C."
6-RS232 Out"
5-RS232 In"
4-Ground"
3-Aux Out"
2-Relay2 Input"
1-Relay1 Input"
Output
Red arrow denotes direction!
of command signal
Input
2-8 to 16 VDC In"
1-Ground
8-485(+)"
7-485(-)
"
6-+5 VDC Out"
5-RLY4 Input (5V)"
*
3-LED Output"
2-D1/Data/F2F Input"
1-D0/CLK Input
Remote Unit
12-RLY2 N.O."
11-RLY2 Com"
10-RLY2 N.C."
9-RLY1 N.O."
8-RLY1 Com"
7-RLY1 N.C."
6-RS232 Out"
5-RS232 In"
4-Ground"
3-Aux In"
2-N/C"
1-N/C"
Relay 3 Input and Output
Relay 3 functions as an Alarm relay and monitors the condition of the communication link between the
Central and Remote units. Relay 3 is activated when power is applied and the communication link between the Central and Remote is functioning. Relay 3 will become deactivated (Alarm condition)" when either the Relay 3 input on the remote is active OR the Remote unit is unable to communicate with the Central unit.
Suprex Operation and Initial Setup
"
Output
2-8 to 16 VDC In"
1-Ground
8-485(+)"
7-485(-)
"
6-+5 VDC Out"
5-Prog Res 2"
*
3-LED Input"
2-D1/Data/F2F Out "
1-D0/Clock Out
Central Unit
12-RLY4 N.O."
11-RLY4 Com"
10-RLY4 N.C."
9-RLY3 N.O."
8-RLY3 Com"
7-RLY3 N.C."
6-RS232 Out"
5-RS232 In"
4-Ground"
3-Aux Out"
2-Relay2 Input"
1-Relay1 Input"
Red arrow denotes direction!
of command signal
Input
2-8 to 16 VDC In"
1-Ground
8-485(+)"
7-485(-)
"
6-+5 VDC Out"
5-RLY4 Input (5V)"
*
3-LED Output"
2-D1/Data/F2F Input"
1-D0/CLK Input
Remote Unit
12-RLY2 N.O."
11-RLY2 Com"
10-RLY2 N.C."
9-RLY1 N.O."
8-RLY1 Com"
7-RLY1 N.C."
6-RS232 Out"
5-RS232 In"
4-Ground"
3-Aux In"
2-N/C"
1-N/C"
Relay 4 Input and Output
2-8 to 16 VDC In"
1-Ground
8-485(+)"
7-485(-)
"
6-+5 VDC Out"
5-Prog Res 2" *
3-LED Input"
2-D1/Data/F2F Out "
1-D0/Clock Out
Suprex Operation and Initial Setup
"
"
"
"
Central Unit
"
"
"
"
"
"
"
"
"
"
"
"
"
12-RLY4 N.O."
11-RLY4 Com"
10-RLY4 N.C."
9-RLY3 N.O."
8-RLY3 Com"
7-RLY3 N.C."
6-RS232 Out"
5-RS232 In"
4-Ground"
3-Aux Out"
2-Relay2 Input"
1-Relay1 Input"
Output
Red arrow denotes direction!
of command signal
2-8 to 16 VDC In"
1-Ground
8-485(+)"
7-485(-)
"
6-+5 VDC Out"
5-RLY4 Input (5V)"
*
3-LED Output"
2-D1/Data/F2F Input"
1-D0/CLK Input
Remote Unit
12-RLY2 N.O."
11-RLY2 Com"
10-RLY2 N.C."
9-RLY1 N.O."
8-RLY1 Com"
7-RLY1 N.C."
6-RS232 Out"
5-RS232 In"
4-Ground"
3-Aux In"
2-N/C"
1-N/C"
Input
Aux Input and Output
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement