BPH1009IUK06EM1.qxd 8/15/06 3:05 PM Page 1

Holmes Products (Europe) Ltd

1 Francis Grove

London SW19 4DT

England

Fax: +44 (0)20 8947 8272

Email: [email protected]

Website address: www.bionaire.com

UK - Free phone Customer Service Helpline – 0800 052 3615

600W Panel Heater with Galileo

™

technology

BPH1009

Fig. 1

Galileo remote

C

Control Panel

D E

MODEL: BPH1009, BPH1009 (Tx)

220-240V~50Hz 500-600W

OPERATING FREQUENCY: 433.9MHz

VOLTAGE SUPPLY: Tx: DC4.5V

© 2006 JCS/THG, LLC

Bionaire ® , the Bionaire logo™ and Galileo™ are trademarks of JCS/THG, LLC.

9100020007404

BPH1009IUK06EM1

INSTRUCTION MANUAL

A. Front Housing

B. Rear Housing

C. Grill

F

D. Galileo remote

E. Control Panel

F. Foot Base (2

)

B

A

BPH1009IUK06EM1.qxd 8/15/06 3:05 PM Page 4

Fig. 2

Fig. 2A Fig. 2B

Fig. 3

Fig. 4

Fig. 4A

Fig. 4B

Fig. 4D

Fig. 4C

I

I

II

Fig. 4E

II

Fig. 5

ENGLISH

CONGRATULATIONS!

Your Bionaire ® Heater has been designed using the latest in technology. With normal care and maintenance, your Bionaire ® Heater will provide years of satisfactory performance.

RETAIN THE FOLLOWING FOR FUTURE

REFERENCE.

IMPORTANT SAFEGUARDS

Mains connection

• Read these instructions carefully, in conjunction with the illustrations, before using the heater.

• Before connecting the heater, check that the voltage indicated on the rating plate corresponds to the mains voltage in your home / office.

• Avoid the use of an extension cord because it may cause the heater to overheat.

•

WARNING: Risk of Fire. Discontinue use if the outlet or plug become hot to the touch.

Overheating may indicate a worn or damaged outlet. Consult a qualified electrician for outlet replacement.

Safe positioning

• Only touch the heater with dry hands.

• DO NOT position where it can be touched by children, especially the very young.

• DO NOT use this heater outdoors.

• This heater is NOT intended for use in bathrooms, laundry areas and other similar indoor locations. NEVER locate heater where it may fall into the bathtub or other water container.

• Position the heater in such a manner that the air flow toward the heater and away from it, is not obstructed.

• Allow a safe area around the heater away from furniture or other objects; at least 50 cm from the top and sides and 200 cm at the front.

• DO NOT use this heater when it is lying on its side.

• If the heater is tipped over, unplug it and allow it to cool before standing it back up.

• DO NOT use the heater in rooms with explosive gas (e.g. petrol) or while using inflammable glue or solvent (e.g. when gluing or varnishing parquet floors, PVC etc.)

• The heater cannot be used adjacent to curtain or combustible material. Curtain or combustible material may be burned if the heater was installed incorrectly.

•

WARNING: In order to avoid overheating,

DO NOT cover the heater ( ).

• DO NOT position the heater directly under a power socket.

• When using the heater in portable condition, do not place in the immediate surroundings of a bath, shower or swimming pool.

• Heater must be installed at least 0.6m above the floor or below the ceiling.

Safety in use

• Extra caution is necessary when the heater is used near children, do not leave heater unattended.

• DO NOT insert any objects into the heater.

• Keep the mains cord at a safe distance from the main body of the heater.

• Prevent overheating of the heater by keeping the air inlet and outlet unblocked. DO NOT hang anything in front of or above the heater.

• If overheating should occur, the built-in overheating safety device will switch off the heater.

• DO NOT use aerosols, inflammable substances or materials sensitive to heat in the flow of hot air.

• In the event of a momentary electrical disturbance , the sample may malfunction and require user to reset the heater.

• Do not use this heater with programmer, timer, or any other device that switch the heater on automatically, since a fire exists if the heater is covered or positioned incorrectly.

• Your Heater HOUSING is made of a durable metal construction that will become hot during operation. Please allow 10 minutes for the heater to cool before handling. If you must move your Heater while it is hot, please use extreme caution. Do not use in the vicinity of children without supervision.

• When using the Galileo TM remote to operate the heater, please ensure that the function shown on the Galileo TM control matches the setting on the control panel. If the settings are different, push the Mode button until settings match. See INSTRUCTION MANUAL for additional information.

Servicing

• Should the heater stop working, first check the fuse in the plug (UK only) or fuse/circuit breaker at the distribution board is operating, before contacting the manufacturer or service agent.

• If the supply cord or plug is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid hazard.

• The heater contains no user serviceable parts and should the product suffer damage or breakdown it must be returned to the manufacturer or their service agent.

2

BPH1009IUK06EM1.qxd 8/15/06 3:05 PM Page 7

BEFORE STARTING YOUR PANEL

HEATER

Please make sure that feet are properly fixed to each end of the unit (see Fig. 2 and assembly instruction insert). Alternatively you can wall mount the unit following the below instructions:

Wall Mounting

IMPORTANT: Before drilling into any wall ensure no electrical cables are present in the area.

NOTE: Due to the multitude of potential mounting surfaces, mounting screws are not included with this product. Please consult a professional or visit your local hardware store to determine which type of screw is best for your particular wall.

1. Remove feet from main unit, if installed.

2. Secure the mounting brackets (Fig. 4B and

3C) to the wall using the dimensions provided in Fig. 4A.

3. Hang main body on wall brackets installing first onto bracket “I” , then onto bracket “II”.

(See Fig. 4D & 4E)

SETTING UP - FIRST USE ONLY:

1. Put batteries into remote control by removing the battery cover located on the reverse side.

Use 3 AAA batteries (Not included) only. DO

NOT mix alkaline and heavy duty batteries.

Do not mix old and new batteries.

WARNING: Remove batteries before discarding the remote control.

2. The “ROOM” temperature will be displayed.

3. Plug heater into mains supply. The power light

(Red) will illuminate to signal that the unit is in stand-by mode.

4. The first time the unit is plugged in, it will beep every two seconds until it is synchronised with the remote. To synchronise the unit with the remote control follow the steps below:-

• Unlock remote by holding down the “MODE” button for 2 seconds until the “LOCK” symbol disappears from the screen. (This must also be done before each use of the remote).

• Once the remote is unlocked, press the

‘MODE” button again and the unit will quickly beep 5 times telling the user the signal was received and the remote is synchronised. In the event that your remote control does not communicate- “sync” with your main unit after reading and following the operating instructions, please follow the below set up:

• Hold down both mode button on the remote control and main unit for 5 seconds

(the power LED will blink once quickly).

• Release the mode button and the main unit will begin to beep.

• Now please follow the above instructions on how to 'sync' your remote control with your unit.

• If you still encounter operational issues please call: 0800 052 3615

5. In the event that your remote control does notcommunicate- “sync” with your main unit after reading and following the operating instructions. Please follow the below set-up:

• Hold down both mode button on the remote control and main unit for 5 seconds (the power LED will blink once quickly).

• Release the mode buttons and the main unit will begin to beep.

• Now please follow above instructions on how to 'sync' your remote control with your unit.

USE OF GALILEO TM REMOTE CONTROL

• The display can show either Fahrenheit or

Celsius. To change the reading on the remote control display, unlock the remote, then turn the remote over and push the button located on the right hand side, under the stand, with a ball point pen tip. This switch will change the reading from ºF to ºC and vice versa.

• Whilst using the remote, the backlight function will automatically turn on when any button is pushed and will turn off after 15 seconds of non-use.

• The maximum transmission distance for the remote control is 30 ft. (9 Metres). Do not use or position the remote more than 30 ft (9

Metres) from heater. For accurate temperature control the remote control must be used in same room as heater.

• When positioning the remote control, use the flip up stand on the reverse side.

• Always position the remote control at least 3 ft. (1 Metre) from the heater in a convenient position away from draughts or anything that would influence the room temperature reading. For example, cold window-sill or under warm lighting.

• Because heat rises and the remote control senses temperature, the remote control should not be positioned higher than 4 ft (1.2

Metres) from the floor.

• NEVER place the remote control on the storage hook on the heater when it is in use.

This will upset the readings and prevent proper and satisfactory operation. (See Fig. 5)

• The "Room" temperature will always display on the remote screen if good batteries are in the remote.

• If the batteries are running low on power, a low battery indicator will appear on the remote. Low batteries will effect transmission distance and the screen contrast. We recommend replacing batteries immediately.

Do not mix old and new batteries.

3

• Every minute while in “AUTO” mode, the remote control communicates with the heater.

If the remote control goes out of range and/or has low batteries, the communication will stop, and after 8 minutes of noncommunication, the heater will shut off.

• Do not cover the remote control whilst in use as this may affect the accuracy of the temperature reading.

HEATER OPERATION WITH REMOTE

When the heater is plugged into the mains supply, the power light (Red) will illuminate to signal that the unit is in stand-by mode.

Manual Operation with remote

1. Press “MODE” button for 2 seconds to unlock the remote.

2. Press “MODE” button on the remote. The remote screen will display “ON”. The “ON” light will illuminate. In this mode, the heater will operate continuously.

Auto Thermostat Operation with remote

1. Press “MODE” button for 2 seconds to unlock the remote.

2. Press “MODE” button on remote until the remote screen displays “ON” and “AUTO”.

The “Set” temperature is displayed next to the

“Room” temp. The “Auto” light on heater will illuminate. The heater and “ON” light will cycle on and off as the unit maintains the “Set” temperature.

3. To turn heater “Off”, unlock remote, then press the “MODE” button and the remote screen display will clear except for the “Room” temperature and the heater will shut off.

NOTE: It is normal for the heater to cycle on and off as it maintains the preset temperature.

To prevent the heater from cycling, you need to raise the thermostat setting.

ADJUSTING SET TEMPERATURE

1. Press ‘MODE’ button for 2 seconds to unlock the remote.

2. Increase - When in “AUTO” mode, press the

(+) button on the remote. The “Set” number will increase with each press. Hold the button down to scroll. The minimum temp is 13ºC and the maximum is 26ºC. The remote scrolls one digit at a time in a continuous loop. 13ºC,

14º...25º, 26º, 13º, 14º....

3. Decrease - When in ‘AUTO’ mode, press the

(-) button on the remote. The “Set” number will decrease with each press. The minimum temp is 13ºC and the maximum is 26ºC. The remote scrolls one digit at a time in a continuous loop. 13º, 14º...25º, 26º, 13º,

14º....

HEATER OPERATION without remote

When the heater is plugged into the mains supply, the power light (Red) ( ) will illuminate to signal that the unit is in stand-by mode.

Remote and heater are OFF:

1. Press the “MODE” button on the heater the first time. The “ON” light illuminates and the heater runs continuously.

2. Press the “MODE” button a second time and the heater shuts off.

NOTE: The “Auto On” light on the heater only illuminates when the heater is set to “auto” mode by the remote.

Remote is ON and Heater is ON:

1. Press the “MODE” button on the heater. The heater will then switch “Modes”; The heater’s lights will reflect the change. The remote will display a different mode - the mode in which it was set to last. If a button is pressed on the remote (after unlocking), the remote’s signal will override the “Mode” on the heater and the two will be back in sync.

TIMER FUNCTIONS

Using Timer to turn heater off (set with heater operating)

1. On the remote, hold ‘MODE’ button for 2 seconds to unlock remote.

2. Push (+) and (-) together at once:

• “Timer” and 1Hr appears on the screen.

3. Push (+) and (-) to adjust the number of hours the heater will run before it automatically shuts itself off.

• You can choose from:1,2,3,4,5,6,7,8 hours

• 1 through 8 will scroll in a continuous loop

4. After you have made your selection, the whole screen flashes for 5 times 5 seconds after last button push of (+) or (-) then goes back to previous mode. The “Timer” remains lit to show the timer function has been set.

5. At any time if you unlock the remote and push the ‘MODE’ button to turn the heater off the timer setting will be erased and “Timer” will disappear from the remote.

6. To check how much time is remaining, press and hold the (+) and (-) buttons simultaneously.

NOTE: The remote does not have to be unlocked to check the time remaining.

Using Timer to turn heater on (set with heater off)

This function is used to preheat a room by setting the timer.

4

BPH1009IUK06EM1.qxd 8/15/06 3:05 PM Page 9

For Example: It’s 8 am, and you want to come home to a warm room at 8 pm. To accomplish this, place the heater in the desired room and set the timer to turn the heater on in

12 hours. Once the timer is activated the heater will run for a preset time of 2 hours. The digital thermostat will maintain the room temperature at a default of 21ºC (72ºF).

1. Hold ‘MODE’ button for 2 seconds to unlock remote.

2. DO NOT push ‘MODE’ again as this will turn heater on.

3. Push (+) and (-) together at once:-

• heater remains off.

• "Timer", "Auto", "On" and 1 Hr. appears on the screen.

4. Push (+) or (-) to adjust the number of hours that will pass before it turns itself on.

• you can choose from;1, 2, 3, 4, 5, 6, 7, 8, 9,

10, 11, 12, 13, 14, 15, 16 hours

• 1 through 16 will scroll in a continuous loop

5. The whole screen flashes for 5 seconds after last button push of (+) or (-) then goes back to previous mode. The timer will turn the heater on and run for 2 hours. During the 2 hours, the digital thermostat will maintain the room in

" 'Auto' mode" at the default of 21ºC (72ºF).

6. At any time if you unlock the remote and push the 'MODE' button on the remote, the timer setting will be erased and "Timer" will disappear from the screen.

7. To check how much time is remaining, press and hold the (+) and (-) buttons simultaneously.

NOTE: The remote does not have to be unlocked to check the time remaining.

AUTO SAFETY SHUT OFF

The heater has a built in safety device which will switch off the heater automatically in case of accidental overheating. It can only resume operation when the user has reset the unit.

To reset the heater

1. Unplug the heater and wait for 30 minutes for the unit to cool down.

2. After the 30 minutes, plug the unit in again and operate normally.

CLEANING AND MAINTENANCE

• Turn off the unit.

• Remove the plug from the wall socket.

• Wait for the heater to cool down sufficiently.

• You may clean the outside of the heater with a damp cloth. DO NOT allow water to come into the appliance. DO NOT use soap or chemicals, which may damage the housing.

Allow sufficient time to dry before plugging the unit back in the socket.

• Clean the air inlet and outlet openings regularly (with normal use at least twice a year) with a vacuum cleaner.

STORAGE TIPS

If you do not plan to use your heater for an extended period of time (i.e. during the summer months), we recommend you to re-pack the unit in its original packaging or any other dust-free packaging and store it in a dry and cool place.

FOR U.K. AND IRELAND ONLY:

If the plug is not suitable for the socket outlets in your home, it can be removed and replaced by a plug of the correct type. Please refer to

"Installation of a plug" below.

Installation of a plug Applicable to

U.K. and Ireland.

WARNING - THIS APPLIANCE MUST BE

EARTHED

The wires in the mains lead are coloured as such:

GREEN AND YELLOW

BROWN

- EARTH

- LIVE

Please note that the colour of these mains wires may not correspond with the colour markings that identify the terminals in your plug.

Please proceed as follows:

The wire which is coloured GREEN AND

YELLOW must be connected to the terminal which is marked with the letter 'E' or by the earth symbol or coloured GREEN or GREEN

AND YELLOW.

The BROWN coloured wire must be connected to the terminal, which is marked with the letter

"L" or is coloured RED.

The BLUE coloured wire must be connected to the terminal, which is marked with the letter "N" or is coloured BLACK.

NOTE: If the terminals in the plug are not marked or if you are unsure or in doubt about the installation of the plug, please contact a qualified electrician.

If a 13A 3-pin plug is fitted, it must be an ASTA approved plug, conforming to BS1363 standard.

Replacement 5A fuses must be BSI or ASTA

BS1362 approved.

5

GUARANTEE

PLEASE KEEP YOUR RECEIPT AS THIS WILL

BE REQUIRED FOR ANY CLAIMS UNDER

THIS GUARANTEE.

• This product is guaranteed for 3 years.

• In the unlikely event of breakdown, please take it back to the place of purchase, with your till receipt and a copy of this guarantee.

• The rights and benefits under this guarantee are additional to your statutory rights which are not affected by this guarantee.

• Holmes Products Europe undertakes within the specific period, to repair or replace free of charge, any part of the appliance found to be defective provided that:

• We are promptly informed of the defect.

• The appliance has not been altered in any way or subjected to misuse or repair by a person other than a person authorised by

Holmes Products Europe.

• No rights are given under this guarantee to a person acquiring the appliance second hand or for commercial or communal uses.

• Any repaired or replaced appliance will be guaranteed on these terms for the remaining portion of the guarantee.

THIS PRODUCT IS MANUFACTURED TO

COMPLY WITH THE E.E.C. DIRECTIVES

73/23/EEC, 89/336/EEC AND 98/37/EEC.

Waste electrical products should not be disposed of with Household waste. Please recycle where facilities exist. Check on the following website for further recycling and WEEE information: www.bionaire.com or e-mail [email protected]

6