Xvision XIR504 Installation & Operation
Xvision XIR504 is a vandal-resistant color dome camera with 15m night vision. Its weatherproof design allows for internal or external installation and is especially suitable for medium to high-risk applications.
Due to the vandal-resistant construction, it can withstand strong impact. The camera delivers high-resolution 480TVL images thanks to its Sony 1/3” Super HAD CCD sensor. It can operate in low-light conditions with a minimum illumination level of 0.1 Lux. In complete darkness, the camera automatically switches to black and white mode and uses integrated long-life infrared LEDs to provide night vision up to 15 meters.
Advertisement
Advertisement
Specification
Model:
Picture Type:
XIR504
Day/Night (B/W & Colour)
Image Sensor:
DSP:
Resolution:
Lens Viewing Angle:
Infra Red Nightvision:
Minimum Illumination:
Sony 1/3” Super HAD CCD
Xvision IXC1DN
480TVL
78°
15 metres
0.1 Lux
Audio:
Operating Voltage:
No
12V DC 750mA Regulated
Suggested Power Supply: 12V DC 1250mA
Mounting:
Weatherproofing:
Dimensions:
Ceiling
No
Ø136x99mm
CCTV
TECHNICAL SUPPORT:
For Technical Support for any Xvision product please contact your local distributor.
LIMITED WARRANTY:
This product is supplied with a 2 Year warranty. The Warranty excludes products that have been misused, (including accidental damage) and damage caused by normal wear and tear. In the unlikely event that you encounter a problem with this product, it should be returned to the place of purchase.
Manufactured exclusively for:
Xvision (Europe) Group,
Head Office: London, U.K.
Email: [email protected]
Web: www.x-vision.co.uk
CCTV
Model:
XIR504
Colour Vandal Resistant
IR Dome Camera
Before you begin
•
Please unpack the box carefully and identify that all the parts are present.
The camera is suitable for indoor or outdoor use. Please bear in mind the following points when choosing a mounting position.
•
The camera must be positioned so that it will not point directly into the sun (sunrise and sunset) or any bright light, as this may cause damage to the camera.
•
Avoid viewing areas where half the area is in bright sunlight and the other half is dark, such as in the shadow of a building. All types of cameras have difficulty in ‘seeing’ with such a large lux level variation.
•
Do not cut the camera cables, this will void the warranty.
•
Make sure you use only the recommended power supply. Damage caused to the camera by incorrect voltage or wiring is not covered by the warranty.
Model:
XIR504
Colour Vandal Resistant Dome
Camera with 15m Nightvision
Package Contents
1 2 3
Installation & Operation
STEP 1: Using the L wrench provided, loosen the vandal resistant housing cover screws (with screws still attached on the cover). The unit has a factory installed side conduit entry and you can adjust the cables to the back conduit entry according to installation requirement (as shown in Figure1).
1. Instruction Manual
2. XIR504 Dome Camera
3. L wrench
Description
THANK YOU VERY MUCH FOR PURCHASING OUR PRODUCT
The XIR504 colour vandal resistant dome camera is designed for medium to high risk applications and is designed to withstand a blow from a 10 pound sledgehammer. It offers very high resolution 480 TVL images from its Sony 1/3"
Super HAD CCD sensor and will provide images in complete darkness up to 15 metres and beyond 15 metres in light levels above 0.1 lux. The camera is designed for internal or external use and ceiling mounting.
Main Features
• Sony 1/3" Super HAD CCD image sensor for 480 TVL resolution images and 0.1 lux low light sensitivity
• Dual mode High Resolution CCD sensor provides very good quality Colour images in low light conditions of 0.1 lux or above and B/W images in low light conditions below 0.1 lux and in complete darkness.
• Integrated Long Life Infra Red LEDs turn on automatically when the camera switches to B/W mode and provide up to 15 metres nightvision
• Vandal resistant for use in areas where the camera is vulnerable to vandalism, can withstand a blow from a 10 pound sledgehammer
• Durable Corrosion Proof Metal Casing designed for internal or external use and ceiling mounting
Figure 1
STEP 2: Set the mounting base onto the wall or ceiling and center it over the mounting hole, using the four retaining screws for the main body supplied in the accessory package (as shown in Figure2).
Figure 2
STEP 3: Set the proper image by moving the camera body (some model types limit the PCB board to 180° rotational adjustment) and set focus by turning the lens to the left or to the right.
STEP 4: When the camera focus adjusment has been completed, use the
Allen key provided to fasten the vandal proof housing to the main body (as shown in Figure 3).
Figure 3
STEP 5: When the camera focus adjusment has been completed, use the
Allen key provided to fasten the vandal proof housing to the main body (as shown in Figure 4).
Figure 4
STEP 6: When using the side conduit cabling, it is suggested to use a metal cover over the cables to prevent external damage and for waterproofing. wind the adhesive tape (PTFE Thread Seal Tape) onto the metal cover before instalation (as shown in Figure5).
Figure 5

Public link updated
The public link to your chat has been updated.
Advertisement