Locking Collars

Locking Collars
JW
JW
JIS
CJ
SF
MC
MC
G
G
■■ Low Torque Series SLDS
SF
■■ Self-Centering Series SLDS
CJ
In This Section:
JIS
Shaft Locking
Devices
HP
■■ High Torque Series SLDS
HP
■■ Medium Torque Series SLDS
■■ Heavy Duty Series SLDS
GD
GD
D
D
SP
SP
T
T
UJ
UJ
VSD
VSD
R
R
SLD
SLD
ED
ED
www.lovejoy-inc.com
425
SLDSLD-1
SF
SF
MC
MC
G
G
HP
CJ
CJ
JIS
JIS
JW
JW
Shaft Locking Devices
HP
Safety Warning
When using Lovejoy products, you must follow these instructions and take the following precautions. Failure
to do so may cause the power transmission product to break and parts to be thrown with sufficient force to
cause severe injury or death.
GD
GD
D
D
T
T
SP
SP
Refer to this Lovejoy Catalog for proper selection, sizing, horsepower, torque range, and speed range
of power transmission products, including elastomeric elements for couplings. Follow the installation
instructions included with the product, and in the individual product catalogs for proper installation of power
transmission products. Do not exceed catalog ratings.
During start up and operation of power transmission product, avoid sudden shock loads. Coupling assembly
should operate quietly and smoothly. If coupling assembly vibrates or makes beating sound, shut down
immediately, and recheck alignment. Shortly after initial operation and periodically thereafter, where
applicable, inspect coupling assembly for: alignment, wear of elastomeric element, bolt torques, and flexing
elements for signs of fatigue. Do not operate coupling assembly if alignment is improper, or where applicable,
if elastomeric element is damaged, or worn to less than 75% of its original thickness.
UJ
UJ
Do not use any of these power transmission products for elevators, man lifts, or other devices that carry
people. If the power transmission product fails, the lift device could fall resulting in severe injury or death.
VSD
VSD
R
R
For all power transmission products, you must install suitable guards in accordance with OSHA and
American Society of Mechanical Engineers Standards. Do not start power transmission product before
suitable guards are in place. Failure to properly guard these products may result in severe injury or death
from personnel contacting moving parts or from parts being thrown from assembly in the event the power
transmission product fails.
If you have any questions, contact the Lovejoy Engineering Department at 1-630-852-0500.
SLD
SLD
ED
ED
SLD-2
426
630-852-0500
CJ
SF
SF
MC
MC
G
G
HP
GD
GD
D
D
SP
SP
T
T
UJ
UJ
VSD
VSD
R
SLD
SLD
Overview.......................................................................................................................................428................... SLD-4
Applications / SLD 900 Series > Selection Data..........................................................................430................... SLD-6
Hub Sizing > Selection Process...................................................................................................431................... SLD-7
Selection Process.........................................................................................................................432................... SLD-8
SLD 900 Series > Dimensional Data............................................................................................433................... SLD-9
SLD 1500 Inch Series > Dimensional Data..................................................................................434................. SLD-10
SLD 1500 Metric Series > Dimensional Data...............................................................................435..................SLD-11
SLD 1850 Inch Series > Dimensional Data..................................................................................436................. SLD-12
SLD 1850 Metric Series > Dimensional Data...............................................................................437................. SLD-13
SLD 1750 Inch Series > Dimensional Data..................................................................................438................. SLD-14
SLD 1750 Metric Series > Dimensional Data...............................................................................439................. SLD-15
SLD 1350 Inch Series > Dimensional Data..................................................................................440................. SLD-16
SLD 1350 Metric Series > Dimensional Data...............................................................................441................. SLD-17
SLD 1450 Inch Series > Dimensional Data..................................................................................442................. SLD-18
SLD 1450 Metric Series > Dimensional Data...............................................................................443................. SLD-19
SLD 2600 Inch Series > Dimensional Data..................................................................................444................. SLD-20
SLD 2600 Metric Series > Dimensional Data...............................................................................445................. SLD-21
SLD 1900 Inch Series > Dimensional Data..................................................................................446................. SLD-22
SLD 1900 Metric Series > Dimensional Data...............................................................................447................. SLD-23
SLD 350 Series > Dimensional Data...........................................................................................448................. SLD-24
HP
Section
Page No.
R
Running Page No.
ED
ED
www.lovejoy-inc.com
427
CJ
Table of Contents
JIS
JIS
JW
JW
Shaft Locking Devices
SLD-3
Shaft Locking Devices
JIS
CJ
CJ
Lovejoy Shaft Locking Devices expand to fill the gap between the shaft and hub, allowing for
easy installation and removal, saving time over traditional interference fit techniques. The contact
pressures created using a Shaft Locking Device can be greater than traditional interference
fit pressures, allowing for more torque to be transmitted or shorter hubs to be used. The easy
installation also allows the hub to be positioned more accurately on the shaft, and can facilitate
angular timing of the hub.
SF
SF
Lovejoy Shaft Locking Devices connect hubs solidly to shafts, using a keyless mechanical
interference fit, to transmit torque or to withstand axial thrust. This mechanical interference fit
utilizes screw tension in the Shaft Locking Device, converted into radial pressure via an inclined
plane. This pressure expands the Shaft Locking Device to eliminate the gap between the hub and
the shaft. The Shaft Locking Device uses the friction bond between the Shaft Locking Device and
the shaft/hub to create a zero backlash connection. This connection is easily releasable to remove
the mechanical interference fit.
JIS
MC
MC
Overview
JW
JW
Overview
Features
Versus Traditional Keyed Connections
■■No impact effect from reversing loads
G
G
■■No Backlash due to fit tolerances
■■Ability to adjust axial position and angular timing
HP
HP
■■No fretting corrosion due to movement at the fit interface
Versus Traditional Interference Fits
GD
GD
■■Easier and quicker to install
■■Higher contact pressures can transmit greater torques
Design Benefits
D
D
■■Easy and quick to remove without damaging the shaft or hub - even after years of service
■■Eliminate cost of machining keyways or splines
T
T
■■Reduce the shaft stress by removing keyways or splines
■■Eliminating keyways often allows the use of a smaller diameter shaft
Lovejoy SLD offers several types of Shaft Locking Devices, designed to be used in just about any
application where a shaft connects to a hub.
UJ
VSD
VSD
UJ
■■Easy removal without damaging the shaft or hub means easier maintenance for your customer
SP
SP
■■Can place anywhere on shaft, and allows for easy angular timing
R
R
ED
ED
SLD
SLD
WARNING
You must refer to page SLD-2 (Page 426) for Important Safety Instructions and
Precautions for the selection and use of these products. Failure to follow the
instructions and precautions can result in severe injury or death.
SLD-4
428
630-852-0500
Shaft Locking Devices
Overview
JW
Metric 14mm to 240mm
Larger sizes on request
22 - 118,010 ft-lb
CJ
Metric shafts 18mm to 200mm
Inch shafts 3/4 to 4 inch
Larger sizes on request
214 - 35,948 ft-lb
■■ High torque
■■ Exceptional concentricity
■■ Self-centering
■■ Axial hub position can move during clamping
Metric shafts 18mm to 200mm
Inch shafts 3/4 to 4 inch
Larger sizes on request
259 - 40,274 ft-lb
■■ High torque
■■ Exceptional concentricity
■■ Self-centering
■■ Axial hub position fixed during clamping
Metric shafts 18mm to 200mm
Inch shafts 3/4 to 4 inch
Larger sizes on request
203 - 34,151 ft-lb
■■ Heavy duty
■■ Very high torque
■■ Self-centering
■■ Exceptional concentricity
Metric shafts 25mm to 240mm
Inch shafts 1 to 6-1/2 inch
Larger sizes on request
532 - 155,461 ft-lb
■■ Medium torque
■■ Allows smaller diameter hubs
■■ Exceptional concentricity
■■ Self-centering
■■ Axial hub position fixed during clamping
Metric shafts 6mm to 130mm
Inch shafts 3/4 to 2-15/16 inch
Larger sizes on request
10 - 18,618 ft-lb
■■ Low torque
■■ Small radial dimensions
■■ Can be combined for greater torque capacity
Metric shafts 6mm to 150mm
Also available with cut ring
Larger sizes on request
1.73 - 9,104 ft-lb
SF
■■ High torque
■■ Exceptional concentricity
■■ Self-centering
■■ Axial hub position fixed during clamping
MC
Metric shafts 18mm to 200mm
Inch shafts 3/4 to 4 inch
Larger sizes on request
273 - 44,625 ft-lb
G
■■ High torque
■■ Exceptional concentricity
■■ Self-centering
■■ Axial hub position can move during clamping
G
Metric shafts 17mm to 400mm
Inch shafts 3/4 to 7-15/16 inch
Larger sizes on request
170 - 565,563 ft-lb
MC
■■ Medium high torque
■■ Self releasing
■■ Not self-centering
■■ Axial hub position fixed during clamping
SF
SLD 1500
CJ
Internal Shaft Locking Device
JIS
■■ Self-centering
■■ Exceptional concentricity
■■ Suitable for hollow shafts
■■ Axial hub position fixed during clamping
■■ Recommended for hollow shafts
JIS
SLD 900
JW
External Shaft Locking Device
HP
GD
GD
SLD 1750
HP
SLD 1850
D
D
SLD 1350
SP
SP
T
T
SLD 1450
UJ
VSD
R
SLD
ED
ED
429
SLD
www.lovejoy-inc.com
R
SLD 350
VSD
SLD 1900
UJ
SLD 2600
SLD-5
Shaft Locking Devices
Applications / SLD 900 Series
SF
JIS
CJ
SF
CJ
MC
HP
GD
GD
HP
G
G
Steps In Selecting A 900 Series SLD
D
D
UJ
Step 2: a. If shaft diameter is the primary consideration, verify that the maximum torque to be transmitted is less than the maximum number listed.
b. If Torque is the primary consideration, use the table to determine the shaft size.
UJ
Torque range:
The maximum torque transmission for shaft diameter between those listed can be approximated using the following formula:
VSD
VSD
SP
SP
T
T
Step 1: Determine the shaft diameter to be used, or the maximum torque to be transmitted.
Ta =
R
R
Where:
SLD
[
Sa - Smin
Smax - Smin
] [
Sa = actual shaft size (in)
Smin = minimum shaft size listed (in)
Smax = maximum shaft size listed (in)
X
Tmax - Tmin
]
+
Tmin
Ta
= actual torque
Tmin = minimum torque listed
Tmax = maximum torque listed
ED
ED
SLD
Pump impellers & turbine rotors
Rolls
Section bar machines
Shaker screens
Sheaves
Ski lifts
Speed reducers
Sprockets
Thermal pumps
Tobacco machines
Vegetable-oil refining machines
Weaving machines
Winches
Wind generators
Worm gears
Gearboxes, reducers, and gear motors
Graphic machines
Helical gears
Industrial sewing machines
Lamination machines
Levers & cams
Meat & fish processing machines
Mechanical presses
Milk processing machines
Milling & drilling machines
Mixer shafts
Moving sidewalks
Packaging machines
Pasta machines
Printing machines
Pulp industry: drive rolls & cylinders
Bevel gears
Braiding machines
Brake drums
Cardboard making machines
Carpet making machines
Chocolate making machines
Clutches
Compressors
Conveyor pulleys
Conveyors
Couplings
Crushers
Fans
Flanges
Flywheels
Footwear machines
JIS
MC
Applications
JW
JW
Selection Process
SLD-6
430
630-852-0500
Shaft Locking Devices
Hub Sizing
Selection Process
JW
JW
Minimum Outer Diameter of Hub
The hub must be of a size to withstand the pressure exerted by the Shaft Locking Device without yielding. Use the following equations to determine the
minimum hub diameter (Dmin) required.
JIS
JIS
f = 0.6
Yp + (ƒ x pH)
Yp – (ƒ x pH)
CJ
K= Yp
=
Yield point of hub material (psi)
ƒ
=
Form factor (see figure 1.)
pH
=
Contact pressure on the hub (psi)
SF
Hub bore (inches)
MC
=
MC
D
SF
f = 0.8
Where:
f=1
G
Figure 1
G
where
CJ
Dmin = D x K,
90,000
GD
45,000
1.00
0.80
0.60
1.00
0.80
0.60
1.00
0.80
0.60
1.25
1.19
1.14
1.17
1.13
1.10
1.08
1.06
1.05
D
f=
7,000
8,000
1.29
1.22
1.16
1.20
1.15
1.11
1.09
1.07
1.05
9,000
1.34
1.26
1.19
1.22
1.18
1.13
1.11
1.08
1.06
1.25
1.20
1.14
1.12
1.09
1.23
1.28
1.22
1.16
1.13
1.10
1.48
1.36
1.26
1.31
1.24
1.18
1.14
1.11
1.54
1.40
1.28
1.35
1.27
1.19
1.16
1.12
14,000
1.60
1.44
1.31
1.38
1.29
1.21
1.17
1.13
1.66
1.48
1.34
1.41
1.31
1.22
1.18
1.14
1.73
1.53
1.36
1.45
1.34
1.24
1.20
1.15
1.08
1.09
1.10
1.11
1.11
1.57
1.39
1.49
1.37
1.26
1.21
1.16
1.12
1.62
1.42
1.53
1.39
1.28
1.22
1.18
1.13
VSD
1.81
1.89
1.68
1.45
1.57
1.42
1.30
1.24
1.19
1.73
1.48
1.61
1.45
1.31
1.25
1.20
1.14
21,000
2.20
1.79
1.52
1.66
1.48
1.33
1.27
1.21
1.15
2.32
1.86
1.55
1.71
1.51
1.35
1.28
1.22
2.47
1.93
1.59
1.76
1.54
1.37
1.30
1.23
2.65
2.00
1.62
1.81
1.58
1.39
1.31
1.24
2.85
2.08
1.66
1.87
1.61
1.41
1.33
1.25
1.18
1.18
2.17
1.70
1.93
1.65
1.44
1.35
1.27
1.19
2.27
1.75
2.00
1.69
1.46
1.36
1.28
1.20
28,000
3.87
2.38
1.79
2.07
1.73
1.48
1.38
1.29
www.lovejoy-inc.com
431
ED
3.11
3.44
1.12
SLD-7
ED
26,000
27,000
SLD
24,000
25,000
1.16
1.17
SLD
22,000
23,000
1.14
R
1.98
2.08
R
19,000
20,000
VSD
17,000
18,000
UJ
15,000
16,000
1.08
SP
12,000
13,000
1.07
T
1.21
1.33
SP
1.29
1.43
UJ
1.38
11,000
T
10,000
D
Pressure on the hub (PSI)
32,000
GD
Hub Material Yield Point
HP
To use the table, find the column corresponding to the Yield Point of the hub material (in psi), and the Form factor “f ” from above (based on the
hub’s length through bore). Use the row with the pH from the specification table for the Shaft Locking Device model you have selected rounded
up to the nearest 1,000 psi. Multiply this K factor by the Hub Bore “D” (in inches) to calculate the minimum required hub OD.
HP
Alternatively, use the table below to determine the Coefficient K.
Shaft Locking Devices
Combined Torque and Axial Loads
JW
If an axial load is present, then the resulting torque that can be transmitted needs to be adjusted as follows:
JIS
Mt Result =
JIS
JW
Selection Process
Mt 2
[ 24 ]
+ Fxd
2
Where:
d
=
shaft diameter (inches)
Mt
=
maximum torque for device (ft-lbs)
F
=
force (lbf)
CJ
CJ
µ = 0.12 which corresponds to a slightly oiled surface
Lovejoy SLD uses
63
= 63 µIN RMS for surface finish
Duty Factor
MC
MC
SF
SF
Coefficients of Friction and Surface Finish
The values Mt and F must be adjusted with a duty factor depending on the setup:
G
G
Load
Motor Type
GD
Combustion
2.0
1.5
2.0
2.5
Number of devices in series
Shaft Locking Device
2
3
4
SLD 1500
0.80
0.75
0.70
SLD 1850
0.80
0.75
0.70
SLD 1350
0.80
0.75
SLD 2600
0.85
T
0.70
Not recommended
Competitive Cross Reference
UJ
UJ
SP
1.5
SP
Lovejoy®
R
Ringfeder®
B-LOC
VSD
VSD
1.0
If more than one Shaft Locking Device is used, the transmissible torque must be reduced by the following factors:
T
R
Heavy overloads
Multiple Shaft Locking Devices Used in Series
D
SLD 1500
Rfn 7012
B400
SLD 900
Rfn 4071
SD 10
SLD 1850
Rfn 7013.0
SLD 1750
Rfn 7013.1
SLD 1350
Rfc 303
B103
SLD 1450
Rfc 306
B106
SLD 1900
RfN 7110
B800
SLD 2600
TAS 3012
B112
SLD 350
RfN 8006
B500
SLD
Lovejoy has a full range of Shaft Locking Devices which are comparable to others that are currently being marketed in North America. The items are stocked in
the Downers Grove facility. Extra large sizes, and special orders can be made with 8 week leadtimes.
ED
ED
SLD
Light overloads
GD
D
HP
HP
Electric
Constant
SLD-8
432
630-852-0500
Shaft Locking Devices
SLD 900 Series
Dimensional Data
JW
JIS
CJ
Mt
T3
JIS
e
l
D
d
ds
C
CJ
MA
= total width of thrust rings (relaxed state)
= width of thrust rings (relaxed state)
= locking screw specifications
= screw tightening torque
= width of gap (relaxed state)
= length of contact
= outer diameter of disc
= hub OD diameter
= shaft diameter
= maximum diametrical clearance
(difference between hub diameter and shaft diameter)
= maximum transmissible torque
= tolerance of hub OD
JW
L
B
T
SLD 900 Series Dimensional Data
T
1.969
55
2.165
62
2.441
68
2.677
75
2.953
80
3.150
90
3.543
100
3.937
110
4.331
115
4.528
125
4.921
130
5.118
140
5.512
155
6.102
165
6.496
175
6.890
185
7.283
195
7.677
200
7.874
220
8.661
240
9.449
+0 - 0.0018
+0 - 0.0021
+0 - 0.0025
+0 - 0.0028
www.lovejoy-inc.com
0.728
0.591
0.433
0.079
0.001
1.969
0.906
0.748
0.551
0.098
0.001
1.969
0.906
0.748
0.551
0.098
0.001
2.362
0.984
0.827
0.630
0.098
0.001
2.835
1.063
0.906
0.709
0.098
0.001
3.150
1.142
0.984
0.787
0.098
0.001
3.543
1.220
1.063
0.866
0.098
0.001
3.937
1.339
1.181
0.906
0.138
0.001
4.331
1.339
1.181
0.906
0.138
0.001
4.528
1.339
1.181
0.906
0.138
0.001
5.433
1.496
1.299
0.984
0.157
0.002
5.709
1.496
1.260
0.984
0.138
0.002
6.102
1.772
1.535
1.181
0.177
0.002
6.693
1.949
1.732
1.339
0.197
0.002
7.283
2.244
1.969
1.535
0.217
0.002
7.402
2.244
1.969
1.535
0.217
0.002
8.465
2.402
2.123
1.654
0.236
0.002
8.465
2.323
2.047
1.654
0.197
0.002
9.055
2.677
2.362
1.811
0.276
0.002
10.433
2.756
2.441
1.969
0.236
0.003
11.417
3.071
2.677
2.205
0.236
0.003
11.811
3.071
2.677
2.205
0.236
0.003
12.992
3.780
3.386
2.795
0.295
0.003
13.780
3.780
3.386
2.795
0.295
0.003
13.780
3.780
3.386
2.795
0.295
0.003
14.567
4.488
4.094
3.465
0.315
0.003
15.945
4.803
4.291
3.622
0.335
0.003
433
MC
50
+0 - 0.0015
1.614
4
M5
3
0.33
5
M5
3
0.44
6
M5
3
6
M5
3
0.44
6
M5
3
0.66
5
M6
9
0.99
7
M6
9
1.32
8
M6
9
8
M6
6
2.43
10
M6
9
2.87
10
M6
9
3.09
7
M8
22
3.75
7
M8
22
4.85
10
M8
22
7.28
12
M8
22
9
M10
44
13.01
9
M10
44
13.89
12
M10
44
12
M10
44
10
M12
74
12
M12
74
33.07
8
M16
184
48.50
8
M16
184
50.71
10
M16
184
79.37
12
M16
184
12
M16
184
105.82
15
M16
184
119.05
12
M20
361
G
1.732
0.001
HP
44
0.039
GD
1.417
0.354
ft-lb
lb
0.44
1.76
10.14
18.96
18.08
22.05
88.18
147.71
SLD-9
ED
36
0.433
Weight
Size
SLD
1.181
0.591
MA
Qty
R
30
1.496
ft-lb
22
37
37
66
79
156
120
210
177
306
297
465
454
719
693
959
885
1,401
1,328
1,770
1,475
2,286
1,844
2,876
2,360
3,393
3,467
5,310
5,089
6,638
5,310
8,113
6,269
8,851
8,113
11,063
10,105
13,424
11,063
14,751
14,751
19,177
26,552
32,453
32,453
36,141
44,254
47,942
48,679
60,480
56,055
65,643
70,068
81,132
88,507
118,010
VSD
0.945
in
UJ
24
+0 - 0.0013
in
SP
0.787
in
T
20
in
D
0.630
in
GD
16
in
HP
0.551
Mt
in
0.433
0.472
0.472
0.551
0.551
0.728
0.728
0.866
0.866
1.063
1.063
1.220
1.250
1.496
1.496
1.654
1.654
1.890
1.890
2.047
1.969
2.362
2.165
2.559
2.362
2.756
2.559
2.953
2.756
3.150
2.953
3.346
3.150
3.543
3.346
3.740
3.543
3.937
3.740
4.134
4.134
4.528
4.528
4.921
4.921
5.315
5.315
5.709
5.512
6.102
5.906
6.299
6.299
6.693
6.693
7.480
G
14
in
MC
in
T
T3
Size
Locking Screws
D
Max
SF
C
SP
e
UJ
l
VSD
B
R
L
SLD
D
ED
ds
SF
d
Shaft Locking Devices
SLD 1500 Inch Series
CJ
SLD 1500 Inch Series Dimensional Data
SF
JIS
G
HP
GD
D
T
SP
SP
UJ
UJ
T
VSD
VSD
D
R
R
GD
SLD
SLD
HP
ED
1
1-1/8
1-3/16
1-1/4
1-3/8
1-7/16
1-1/2
1-5/8
1-11/16
1-3/4
1-7/8
1-15/16
2
2-1/8
2-3/16
2-1/4
2-3/8
2-7/16
2-1/2
2-9/16
2-5/8
2-11/16
2-3/4
2-7/8
2-15/16
3
3-1/8
3-1/4
3-3/8
3-7/16
3-1/2
3-3/4
3-7/8
3-15/16
4
4-3/16
4-7/16
4-1/2
4-15/16
5
5-7/16
5-1/2
6
6-7/16
6-1/2
6-15/16
7
7-1/2
7-7/8
8
G
ED
Size
3/4
7/8
MC
MC
SF
CJ
= total width (relaxed state)
= width of thrust rings (relaxed state)
= length of contact
= locking screw specifications
= screw tightening torque
= outer diameter of shaft locking device
= shaft diameter
= maximum transmissible axial force
= maximum transmissible torque
= pressure on the hub
= pressure on the shaft
= tolerance of shaft
= tolerance of hub bore
JIS
L
B
l
T
MA
D
d
F
Mt
pH
pS
T1
T2
JW
JW
Dimensional Data
SLD-10
d
in
0.750
0.088
1.000
1.125
1.188
1.250
1.375
1.438
1.500
1.625
1.688
1.750
1.875
1.938
2.000
2.125
2.188
2.250
2.375
2.438
2.500
2.563
2.625
2.688
2.750
2.875
2.938
3.000
3.125
3.250
3.375
3.438
3.500
3.750
3.875
3.938
4.000
4.188
4.438
4.500
4.938
5.000
5.438
5.500
6.000
6.438
6.500
6.938
7.000
7.500
7.875
8.000
D
T1
in
+0 -0.0013
+0 -0.0025
+0 -0.0030
+0 -0.0035
+0 -0.0040
+0 -0.0045
in
1.850
1.850
1.969
2.165
2.159
2.362
2.365
2.559
2.559
2.953
2.953
2.953
3.150
3.150
3.346
3.346
3.543
3.543
3.531
3.740
3.740
3.737
4.331
4.331
4.337
4.528
4.724
4.724
4.921
4.921
5.118
5.118
5.305
5.709
5.709
5.843
6.102
6.496
6.496
7.087
7.087
7.480
7.492
8.268
8.858
8.858
9.252
9.252
9.252
9.823
10.235
10.504
B
T2
in
-0 +0.002
-0 +0.0025
-0 +0.0033
-0 +0.0035
-0 +0.0040
-0 +0.0045
in
0.787
0.787
0.787
0.787
0.813
0.787
0.787
0.787
0.787
0.945
0.945
0.945
0.945
0.945
0.945
0.945
0.945
0.945
0.945
0.945
0.945
0.945
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.260
1.260
1.260
1.260
1.260
1.260
1.496
1.496
1.496
1.496
1.496
1.732
1.732
1.732
1.732
2.051
2.051
2.051
l
in
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.787
0.787
0.787
0.787
0.787
0.787
0.787
0.787
0.787
0.787
0.787
0.787
0.787
0.945
0.945
0.945
0.945
0.945
0.945
0.945
0.945
0.945
0.945
0.945
0.945
1.024
1.024
1.024
1.024
1.024
1.024
1.339
1.339
1.339
1.339
1.339
1.496
1.496
1.496
1.496
1.811
1.811
1.811
L
in
1.023
1.023
1.023
1.023
1.049
1.023
1.023
1.023
1.023
1.260
1.260
1.260
1.260
1.260
1.260
1.260
1.260
1.260
1.260
1.260
1.260
1.260
1.496
1.496
1.496
1.496
1.496
1.496
1.496
1.496
1.496
1.496
1.496
1.496
1.732
1.732
1.732
1.732
1.732
1.771
1.968
1.968
1.968
1.968
1.968
2.283
2.283
2.283
2.283
2.602
2.602
2.602
434
T
Max
Max
F
Mt
pH
Pressures
pS
lbf
6,208
6,199
6,192
9,301
9,297
9,312
9,303
11,637
11,632
17,516
17,522
17,513
17,510
16,487
20,604
20,612
20,604
20,608
20,605
20,608
20,611
20,605
31,122
31,122
31,121
31,121
31,120
31,120
31,119
31,119
31,118
31,118
31,118
37,344
45,560
46,068
46,062
46,063
49,136
49,136
61,421
61,421
67,562
67,562
79,844
86,683
86,684
94,564
94,563
110,326
118,205
118,206
ft-lb
194
226
258
436
460
485
533
697
727
1,186
1,232
1,277
1,368
1,331
1,717
1,825
1,878
1,932
2,039
2,093
2,147
2,200
3,404
3,485
3,566
3,728
3,809
3,890
4,052
4,214
4,376
4,457
4,538
5,835
7,356
7,558
7,677
8,037
9,085
9,213
12,636
12,796
15,307
15,483
19,961
23,251
23,477
27,335
27,581
34,477
38,786
39,402
psi
13,293
13,293
12,490
17,038
17,086
15,617
15,598
18,019
18,019
19,993
19,993
19,993
18,742
17,640
20,758
20,758
19,604
19,604
19,671
18,571
18,571
18,586
20,169
20,169
20,141
19,291
19,291
18,491
18,491
17,751
17,751
17,067
17,067
19,759
20,676
20,906
20,423
19,556
19,594
19,594
17,169
17,169
17,894
17,865
19,132
17,352
17,352
18,123
18,123
16,451
16,917
16,483
psi
32,789
28,105
24,592
32,789
31,064
29,511
26,828
32,077
30,740
36,331
34,986
33,736
31,487
28,679
34,728
32,686
31,752
30,870
29,245
28,495
27,783
27,105
33,276
32,503
31,764
30,383
29,736
29,117
27,952
26,877
25,882
25,411
24,957
27,952
30,456
30,306
29,833
28,497
28,684
28,286
24,643
24,335
24,615
24,335
26,363
23,877
23,647
24,170
23,954
21,546
21,986
21,643
Locking Screws
Qty
8
8
8
12
12
12
12
15
15
12
12
12
12
12
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
18
15
15
15
15
16
16
20
20
22
22
26
22
22
24
24
28
30
30
Size
M6
M6
M6
M6
M6
M6
M6
M6
M6
M8
M8
M8
M8
M8
M8
M8
M8
M8
M8
M8
M8
M8
M10
M10
M10
M10
M10
M10
M10
M10
M10
M10
M10
M10
M12
M12
M12
M12
M12
M12
M12
M12
M12
M12
M12
M14
M14
M14
M14
M14
M14
M14
MA
ft-lb
11
11
11
11
11
11
11
11
11
27
27
27
27
27
27
27
27
27
27
27
27
27
52
52
52
52
52
52
52
52
52
52
52
52
91
91
91
91
91
91
91
91
91
91
91
138
138
138
138
138
138
138
630-852-0500
Shaft Locking Devices
SLD 1500 Metric Series
Dimensional Data
JW
= total width (relaxed state)
= width of thrust rings (relaxed state)
= length of contact
= locking screw specifications
= screw tightening torque
= outer diameter of shaft locking device
= shaft diameter
= maximum transmissible axial force
= maximum transmissible torque
= pressure on the hub
= pressure on the shaft
= tolerance of shaft
= tolerance of hub bore
JW
JIS
JIS
CJ
CJ
L
B
l
T
MA
D
d
F
Mt
pH
pS
T1
T2
SLD 1500 Metric Series Dimensional Data
435
SF
MC
G
HP
GD
D
T
MA
ft-lb
11.80
11.80
11.80
11.80
11.80
11.80
11.80
11.80
11.80
11.80
11.80
11.80
11.80
28.00
28.00
28.00
28.00
28.00
28.00
28.00
55.00
55.00
55.00
55.00
55.00
55.00
96.00
96.00
96.00
96.00
96.00
96.00
96.00
148.00
148.00
148.00
148.00
221.00
221.00
221.00
302.00
302.00
435.00
435.00
583.00
583.00
583.00
583.00
885.00
885.00
885.00
885.00
SLD-11
ED
-0 +0.0061
Size
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M8
M8
M8
M8
M8
M8
M8
M10
M10
M10
M10
M10
M10
M12
M12
M12
M12
M12
M12
M12
M14
M14
M14
M14
M16
M16
M16
M18
M18
M20
M20
M22
M22
M22
M22
M24
M24
M24
M24
SLD
www.lovejoy-inc.com
-0 +0.0055
Qty
8
8
8
8
8
8
8
12
12
12
12
15
15
12
12
12
12
15
15
15
15
15
15
15
18
18
15
15
16
20
22
24
26
22
24
28
30
26
30
34
32
36
36
36
36
36
36
40
40
40
42
44
R
+0 -0.0061
-0 +0.0051
pS
psi
36,985
34,954
33,069
31,473
28,572
26,252
25,237
33,794
31,473
29,443
26,977
31,038
29,443
34,809
32,489
30,458
29,298
33,214
30,458
28,137
34,954
32,634
30,603
28,863
27,267
30,893
33,214
30,168
29,443
25,962
26,542
26,977
27,412
25,527
26,252
23,931
24,366
23,641
24,947
26,107
23,061
24,221
24,511
23,206
23,206
22,046
20,885
22,046
25,382
24,366
24,511
24,656
VSD
+0 -0.0055
-0 +0.0045
pH
psi
13,343
13,343
13,343
13,343
13,343
12,618
12,618
17,114
17,114
15,954
15,954
18,130
18,130
20,305
20,305
17,405
18,855
21,756
20,305
18,855
23,206
21,756
20,305
20,305
18,855
21,756
23,206
21,756
21,756
18,855
20,305
20,305
21,756
20,305
20,305
18,855
18,855
18,855
20,305
21,756
18,855
20,305
20,305
18,855
18,855
17,405
17,405
17,405
20,305
18,855
20,305
20,305
UJ
+0 -0.0051
-0 +0.0040
Mt
ft-lb
170
184
192
207
229
243
258
428
465
494
538
730
767
1,180
1,254
1,328
1,401
1,918
2,102
2,286
3,946
4,226
4,499
4,794
5,089
6,417
8,261
9,072
10,547
14,309
16,964
19,840
22,864
26,774
30,978
38,206
43,000
54,653
68,741
84,451
103,996
125,386
173,696
184,391
242,658
255,492
269,210
313,759
452,421
472,999
518,285
565,563
SP
+0 -0.0045
-0 +0.0035
F
lbf
6,083
6,245
6,153
6,295
6,336
6,182
6,295
9,314
9,442
9,414
9,378
11,714
11,690
17,128
16,986
16,861
17,085
21,255
21,357
21,443
34,364
34,351
34,283
34,383
34,471
41,176
50,357
50,275
53,579
67,097
73,866
80,631
87,113
96,007
104,911
122,580
131,064
151,439
174,602
198,005
226,415
254,783
330,891
330,601
410,901
409,862
410,276
455,399
626,808
626,826
658,222
689,534
T
+0 -0.0040
-0 +0.0030
in
1.024
1.024
1.024
1.024
1.024
1.024
1.024
1.024
1.024
1.024
1.024
1.024
1.024
1.260
1.260
1.260
1.260
1.260
1.260
1.260
1.496
1.496
1.496
1.496
1.496
1.496
1.732
1.732
1.732
1.969
1.969
1.969
1.969
2.283
2.283
2.598
2.598
2.835
2.835
2.835
3.307
3.307
3.858
3.858
4.409
4.409
4.409
4.409
4.961
4.961
4.961
4.961
D
+0 -0.0035
-0 +0.0025
in
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.787
0.787
0.787
0.787
0.787
0.787
0.787
0.945
0.945
0.945
0.945
0.945
0.945
1.024
1.024
1.024
1.339
1.339
1.339
1.339
1.496
1.496
1.811
1.811
1.969
1.969
1.969
2.362
2.362
2.835
2.835
3.307
3.307
3.307
3.307
3.780
3.780
3.780
3.780
GD
+0 -0.0030
-0 +0.002
in
0.787
0.787
0.787
0.787
0.787
0.787
0.787
0.787
0.787
0.787
0.787
0.787
0.787
0.945
0.945
0.945
0.945
0.945
0.945
0.945
1.102
1.102
1.102
1.102
1.102
1.102
1.260
1.260
1.260
1.496
1.496
1.496
1.496
1.732
1.732
2.047
2.047
2.205
2.205
2.205
2.598
2.598
3.071
3.071
3.543
3.543
3.543
3.543
4.016
4.016
4.016
4.016
HP
+0 -0.0025
T2
in
SP
+0 -0.0013
in
1.850
1.850
1.850
1.850
1.850
1.969
1.969
2.165
2.165
2.362
2.362
2.559
2.559
2.953
2.953
3.150
3.150
3.346
3.543
3.740
4.331
4.528
4.724
4.921
5.118
5.315
5.709
6.102
6.496
7.087
7.480
7.874
8.268
8.858
9.252
9.843
10.236
11.220
12.008
12.795
13.976
14.764
15.945
16.732
17.913
18.701
19.488
20.276
21.457
22.244
23.031
23.819
UJ
T1
in
T
Locking Screws
G
in
0.669
0.709
0.748
0.787
0.866
0.945
0.984
1.102
1.181
1.260
1.378
1.496
1.575
1.654
1.772
1.890
1.969
2.165
2.362
2.559
2.756
2.953
3.150
3.346
3.543
3.740
3.937
4.331
4.724
5.118
5.512
5.906
6.299
6.693
7.087
7.480
7.874
8.661
9.449
10.236
11.024
11.811
12.598
13.386
14.173
14.961
15.748
16.535
17.323
18.110
18.898
19.685
Pressures
MC
Size
17x47
18x47
19x47
20x47
22x47
24x50
25x50
28x55
30x55
32x60
35x60
38x65
40x65
42x75
45x75
48x80
50x80
55x85
60x90
65x95
70x110
75x115
80x120
85x125
90x130
95x135
100x145
110x155
120x165
130x180
140x190
150x200
160x210
170x225
180x235
190x250
220x260
220x285
240x305
260x325
280x355
300x375
320x405
340x425
360x455
380x475
400x495
420x515
440x545
460x565
480x585
500x605
Max
VSD
Max
R
L
l
SLD
B
ED
D
SF
d
Shaft Locking Devices
SLD 1850 Inch Series
CJ
JIS
CJ
= total width (relaxed state)
= width of thrust rings (relaxed state)
= length of contact
= locking screw specifications
= screw tightening torque
= outer diameter of shaft locking device
= shaft diameter
= maximum transmissible axial force
= maximum transmissible torque
= pressure on the hub
= pressure on the shaft
= tolerance of shaft
= tolerance of hub bore
JIS
L
B
l
T
M
A
D
d
F
Mt
pH
pS
T1
T2
JW
JW
Dimensional Data
SLD 1850 Inch Series Dimensional Data
SF
SF
MC
3/4
MC
Size
G
HP
GD
D
T
1.850
Max
F
Max
Mt
pH
pS
ft-lb
psi
psi
Qty
Size
MA
ft-lb
10
in
in
in
lbf
1.102
0.669
1.339
9,181
287
19,725
36,840
6
M6
1.102
0.669
1.339
9,104
332
19,725
31,763
6
M6
10
1.969
1.102
0.669
1.339
9,063
378
18,565
27,992
6
M6
10
1.850
1.000
T
Locking Screws
Pressures
-0 +0.0015
2.165
1.102
0.669
1.339
9,346
438
16,824
24,076
6
M6
10
1.102
0.669
1.339
9,153
453
16,824
23,351
6
M6
10
1-1/4
1.250
2.362
1.102
0.669
1.339
12,377
645
20,595
29,153
8
M6
10
1.375
2.362
1.102
0.669
1.339
12,307
705
20,595
26,687
8
M6
10
1-7/16
1.438
2.559
1.102
0.669
1.339
12,437
745
19,000
25,237
8
M6
10
1-1/2
1.500
1-3/8
+0 -0.0016
-0 +0.0018
2.559
1.102
0.669
1.339
12,238
765
19,000
24,511
8
M6
10
1.625
2.953
1.299
0.787
1.614
23,377
1,583
26,832
36,405
8
M8
26
1-11/16
1.688
2.953
1.299
0.787
1.614
23,612
1,660
26,832
34,664
8
M8
26
1-3/4
1.750
2.953
1.299
0.787
1.614
23,295
1,699
26,832
33,939
8
M8
26
1-7/8
1.875
3.150
1.319
0.787
1.614
23,725
1,853
25,237
31,038
8
M8
26
1-15/16
1.938
3.150
1.319
0.787
1.614
23,434
1,892
25,237
30,458
8
M8
26
2
2.000
3.150
1.319
0.787
1.614
23,631
1,969
25,237
29,298
8
M8
26
2-1/8
2.125
3.346
1.319
0.787
1.614
23,549
2,085
23,641
27,557
8
M8
26
2-3/16
2.188
3.346
1.319
0.787
1.614
23,726
2,163
23,641
26,687
8
M8
26
2-1/4
2.250
3.543
1.319
0.787
1.614
23,476
2,201
22,336
26,107
8
M8
26
2-3/8
2.375
3.543
1.319
0.787
1.614
23,411
2,317
22,336
24,802
8
M8
26
1-5/8
T
SP
SP
+0 -0.0013
0.750
T2
in
L
2.165
D
2.438
1.319
0.787
1.614
23,573
2,394
21,176
24,076
8
M8
26
1.319
0.787
1.614
23,720
2,471
21,176
23,351
8
M8
26
2.563
3.740
1.319
0.787
1.614
23,508
2,510
21,176
22,916
8
M8
26
2.688
4.331
1.575
0.945
1.969
38,202
4,278
24,802
29,733
8
M10
52
2-3/4
2.750
4.331
1.575
0.945
1.969
38,435
4,404
24,802
29,008
8
M10
52
2-7/8
2.875
4.528
1.575
0.945
1.969
38,340
4,593
23,786
27,702
8
M10
52
2.938
4.528
1.575
0.945
1.969
38,549
4,718
23,786
26,977
8
M10
52
3.000
4.724
1.575
0.945
1.969
38,253
4,782
22,771
26,687
8
M10
52
3-1/4
3.250
4.921
1.575
0.945
1.969
48,203
6,527
27,412
30,458
10
M10
52
3-3/8
3.375
4.921
1.575
0.945
1.969
48,096
6,763
27,412
29,443
10
M10
52
2-1/2
2.500
2-9/16
2-11/16
3
VSD
2-15/16
R
3.438
3.500
3-3/4
3.750
3-15/16
SLD
3-7/16
3-1/2
3.740
-0 +0.0022
3.740
2-7/16
UJ
UJ
in
l
1.188
GD
VSD
T1
in
B
1.125
HP
R
G
SLD
D
1-3/16
1-1/8
4
+0 -0.0018
5.118
1.575
0.945
1.969
47,767
6,842
26,252
29,153
10
M10
52
1.575
0.945
1.969
47,996
6,999
26,252
28,427
10
M10
52
5.315
1.575
0.945
1.969
47,813
7,471
25,382
26,687
10
M10
52
3.938
5.709
1.732
1.024
2.205
53,291
8,743
24,221
28,137
8
M12
85
4.000
5.709
1.732
1.024
2.205
53,507
8,918
24,221
27,557
8
M12
85
+0 -0.0022
5.118
-0 +0.0025
ED
ED
in
0.875
7/8
1
d
SLD-12
436
630-852-0500
Shaft Locking Devices
SLD 1850 Metric Series
Dimensional Data
JW
= total width (relaxed state)
= width of thrust rings (relaxed state)
= length of contact
= locking screw specifications
= screw tightening torque
= outer diameter of shaft locking device
= shaft diameter
= maximum transmissible axial force
= maximum transmissible torque
= pressure on the hub
= pressure on the shaft
= tolerance of shaft
= tolerance of hub bore
JW
JIS
JIS
CJ
CJ
L
B
l
T
M
A
D
d
F
Mt
pH
pS
T1
T2
L
Max
+0 -0.0025
-0 +0.0028
6
6
6
6
6
6
6
M6
M6
M6
M6
M6
M6
M6
10
10
10
10
10
10
10
9,202
12,280
12,281
12,270
12,275
23,541
23,540
23,539
453
645
705
765
805
1,622
1,738
1,853
16,824
20,595
20,595
19,000
19,000
26,832
26,832
25,237
23,351
29,153
26,687
24,511
23,351
32,343
33,214
31,038
6
8
8
8
8
8
8
8
M6
M6
M6
M6
M6
M8
M8
M8
10
10
10
10
10
26
26
26
1.614
1.614
1.614
1.614
1.969
1.969
1.969
1.969
1.969
1.969
2.205
2.205
2.205
23,533
23,535
23,537
23,539
38,352
38,349
38,352
47,940
47,939
47,939
53,298
53,296
59,960
1,930
2,123
2,317
2,510
4,404
4,718
5,033
6,685
7,078
7,471
8,743
9,617
11,803
25,237
23,641
22,336
21,176
24,802
23,786
22,771
27,412
26,252
25,382
24,221
22,626
23,931
29,878
27,122
24,802
22,916
29,008
26,977
25,382
29,733
28,137
26,687
28,137
23,061
23,786
8
8
8
8
8
8
8
10
10
10
8
8
9
M8
M8
M8
M8
M10
M10
M10
M10
M10
M10
M12
M12
M12
26
26
26
26
52
52
52
52
52
52
85
85
85
2.205
2.677
2.677
2.677
3.071
3.071
79,946
81,609
90,676
108,813
108,813
108,813
17,049
18,742
22,312
28,560
30,345
32,130
22,336
21,611
22,771
26,107
18,855
17,985
24,366
22,191
23,061
25,817
20,305
19,145
12
9
10
12
12
12
M12
M14
M14
M14
M14
M14
85
136
136
136
136
136
G
0.787
0.787
0.787
0.787
0.945
0.945
0.945
0.945
0.945
0.945
1.024
1.024
1.024
1.339
1.339
1.339
1.339
1.732
1.732
HP
1.319
1.319
1.319
1.319
1.575
1.575
1.575
1.575
1.575
1.575
1.732
1.732
1.732
2.047
2.126
2.126
2.126
2.520
2.520
GD
1.339
1.339
1.339
1.339
1.339
1.614
1.614
1.614
D
0.669
0.669
0.669
0.669
0.669
0.787
0.787
0.787
T
1.102
1.102
1.102
1.102
1.102
1.299
1.299
1.319
SP
9,242
9,253
9,217
9,197
9,198
9,208
9,201
MC
38,870
36,840
34,954
31,763
29,153
27,992
24,947
1.339
1.339
1.339
1.339
1.339
1.339
1.339
2.520
1.732
3.071
136,016
42,394
21,176
22,626
15
M14
136
2.520
1.732
3.071
136,016
44,625
20,305
21,611
15
M14
136
www.lovejoy-inc.com
437
SLD-13
ED
ED
-0 +0.0032
19,725
19,725
19,725
19,725
18,565
18,565
16,824
0.669
0.669
0.669
0.669
0.669
0.669
0.669
SLD
9.843
10.236
273
288
302
332
362
378
423
1.102
1.102
1.102
1.102
1.102
1.102
1.102
R
+0 -0.0028
-0 +0.0025
MA
ft-lb
UJ
+0 -0.0021
-0 +0.0021
Size
VSD
7.480
7.874
+0 -0.0018
Qty
UJ
190x250
200x260
3.150
3.346
3.543
3.740
4.331
4.528
4.724
4.921
5.118
5.315
5.709
6.102
6.496
7.087
7.480
7.874
8.268
8.858
9.252
-0 +0.0018
pS
psi
SP
1.969
2.165
2.362
2.559
2.756
2.953
3.150
3.346
3.543
3.740
3.937
4.331
4.724
5.118
5.512
5.906
6.299
6.693
7.087
+0 -0.0015
pH
psi
in
T
50x80
55x85
60x90
65x95
70x110
75x115
80x120
85x125
90x130
95x135
100x145
110x155
120x165
130x180
140x190
150x200
160x210
170x225
180x235
2.165
2.362
2.362
2.559
2.559
2.953
2.953
3.150
-0 +0.0015
Mt
ft-lb
in
D
1.181
1.260
1.378
1.496
1.575
1.654
1.772
1.890
+0 -0.0013
F
lbf
in
GD
30x55
32x60
35x60
38x65
40x65
42x75
45x75
48x80
1.850
1.850
1.850
1.850
1.969
1.969
2.165
T2
in
HP
0.709
0.748
0.787
0.866
0.945
0.984
1.102
in
G
18x47
19x47
20x47
22x47
24x50
25x50
28x55
T1
in
T
Locking Screws
SLD
in
Pressures
MC
Size
Max
VSD
l
R
B
D
SF
d
SF
SLD 1850 Metric Series Dimensional Data
Shaft Locking Devices
SLD 1750 Inch Series
JIS
CJ
CJ
SLD 1750 Inch Series Dimensional Data
SF
SF
= total width (relaxed state)
= width of thrust rings (relaxed state)
= width to flange
= length of contact
= locking screw specifications
= screw tightening torque
= outer diameter of shaft locking device
= diameter to flange
= shaft diameter
= maximum transmissible axial force
= maximum transmissible torque
= pressure on the hub
= pressure on the shaft
= tolerance of shaft
= tolerance of hub bore
JIS
L
B
A
l
T
MA
D
D1
d
F
Mt
pH
pS
T1
T2
JW
JW
Dimensional Data
d
HP
GD
D
T
SP
1.850
D1
T2
in
-0 +0.0015
in
A
in
B
l
in
L
T
Max
Max
F
Mt
lbf
ft-lb
Pressures
pH
Locking Screws
pS
Size
MA
ft-lb
in
in
psi
psi
Qty
2.204
0.866 1.102
0.669
1.339
7,623
238
15,515
26,024
6
M6
13
2.204
0.866 1.102
0.669
1.339
7,623
278
15,515
22,306
6
M6
13
1
1.000
1.969
2.323
0.866 1.102
0.669
1.339
7,623
318
14,577
19,518
6
M6
13
1-1/8
1.125
2.165
2.519
0.866 1.102
0.669
1.339
7,623
357
13,258
17,349
6
M6
13
1.188
2.165
2.519
0.866 1.102
0.669
1.339
7,623
377
13,258
16,436
6
M6
13
1-1/4
1.250
2.362
2.716
0.866 1.102
0.669
1.339
10,164
529
16,202
20,819
8
M6
13
1-3/8
1.375
2.362
2.716
0.866 1.102
0.669
1.339
10,164
582
16,202
18,926
8
M6
13
1-3/16
1.438
2.913
0.866 1.102
0.669
1.339
10,164
609
14,955
18,103
8
M6
13
2.913
0.866 1.102
0.669
1.339
10,164
635
14,955
17,349
8
M6
13
1.625
2.953
3.307
0.984 1.299
0.787
1.614
18,806
1,273
20,381
24,691
8
M8
30
1.688
2.953
3.307
0.984 1.299
0.787
1.614
18,806
1,322
20,381
23,777
8
M8
30
1-3/4
1.750
2.953
3.307
0.984 1.299
0.787
1.614
18,806
1,371
20,381
22,928
8
M8
30
1-7/8
1.875
3.150
3.504
0.945 1.319
0.787
1.614
18,806
1,469
19,106
21,399
8
M8
30
1-15/16
1-1/2
1.500
1-5/8
1-11/16
2.559
-0 +0.0018
2.559
1-7/16
+0 -0.0016
1.938
3.150
3.504
0.945 1.319
0.787
1.614
18,806
1,518
19,106
20,709
8
M8
30
2
2.000
3.150
3.504
0.945 1.319
0.787
1.614
18,806
1,567
19,109
20,062
8
M8
30
2-1/8
2.125
3.346
3.700
0.945 1.319
0.787
1.614
18,806
1,665
17,987
18,882
8
M8
30
2-3/16
2.188
3.346
3.700
0.945 1.319
0.787
1.614
18,806
1,714
17,987
18,342
8
M8
30
2.250
3.543
3.897
0.945 1.319
0.787
1.614
18,806
1,763
16,987
17,833
8
M8
30
2-3/8
2.375
3.543
3.897
0.945 1.319
0.787
1.614
18,806
1,861
16,987
16,894
8
M8
30
2-7/16
2.438
3.740
4.094
0.945 1.319
0.787
1.614
18,806
1,910
16,092
16,461
8
M8
30
3.740
4.094
0.945 1.319
0.787
1.614
18,806
1,959
16,092
16,049
8
M8
30
2-1/4
UJ
2-1/2
SP
UJ
+0 -0.0013
T
2.500
+0 -0.0018
-0 +0.0022
2-9/16
2.563
3.740
4.094
0.945 1.319
0.787
1.614
18,806
2,008
16,092
15,658
8
M8
30
2-11/16
2.688
4.331
4.685
1.142 1.575
0.945
1.969
31,017
3,473
19,100
20,520
8
M10
61
3,554
19,100
20,053
8
M10
61
2-3/4
VSD
VSD
0.875
D
2.750
4.331
4.685
1.142 1.575
0.945
1.969
31,017
2.875
4.528
4.882
1.142 1.575
0.945
1.969
31,017
3,716
18,269
19,182
8
M10
61
2-15/16
2.938
4.528
4.882
1.142 1.575
0.945
1.969
31,017
3,796
18,269
18,773
8
M10
61
3
3.000
4.724
5.078
1.142 1.575
0.945
1.969
31,017
3,877
17,511
18,382
8
M10
61
3-1/4
3.250
4.921
5.275
1.142 1.575
0.945
1.969
31,017
4,200
16,810
16,968
8
M10
61
3-3/8
3.375
4.921
5.275
1.142 1.575
0.945
1.969
38,771
5,452
21,012
20,425
10
M10
61
2-7/8
3.438
SLD
3-7/16
3-1/2
R
R
7/8
in
1.850
GD
SLD
0.750
T1
in
HP
3.500
5.118
+0 -0.0022
5.118
-0 +0.0025
5.470
1.142 1.575
0.945
1.969
38,771
5,553
20,203
20,053
10
M10
61
5.470
1.142 1.575
0.945
1.969
38,771
5,654
20,203
19,695
10
M10
61
3-3/4
3.750
5.315
5.669
1.142 1.575
0.945
1.969
38,771
6,058
19,455
18,382
10
M10
61
3-15/16
3.938
5.708
6.603
1.220 1.732
1.024
2.205
45,836
7,520
19,768
18,627
8
M12
107
4.000
5.709
6.603
1.220 1.732
1.024
2.205
45,836
7,639
19,766
18,336
8
M12
107
4
ED
ED
in
3/4
G
G
MC
MC
Size
D
SLD-14
438
630-852-0500
Shaft Locking Devices
SLD 1750 Metric Series
Dimensional Data
JW
= total width (relaxed state)
= width of thrust rings (relaxed state)
= width to flange
= length of contact
= locking screw specifications
= screw tightening torque
= outer diameter of shaft locking device
= diameter to flange
= shaft diameter
= maximum transmissible axial force
= maximum transmissible torque
= pressure on the hub
= pressure on the shaft
= tolerance of shaft
= tolerance of hub bore
JIS
CJ
SF
A
B
l
L
T
Qty
Size
MA
ft-lb
2.205
2.205
2.205
2.205
2.323
2.323
2.520
2.520
2.717
2.717
2.913
2.913
3.307
3.307
3.504
3.504
3.701
3.898
4.094
4.685
4.882
5.079
5.276
5.472
5.669
6.063
6.457
6.850
7.441
7.835
8.228
8.622
9.213
9.606
10.197
10.591
0.866
0.866
0.866
0.866
0.866
0.866
0.866
0.866
0.866
0.866
0.866
0.866
0.984
0.984
0.945
0.945
0.945
0.945
0.945
1.142
1.142
1.142
1.142
1.142
1.142
1.220
1.220
1.220
1.535
1.535
1.535
1.535
1.929
1.929
1.929
1.929
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.299
1.299
1.319
1.319
1.319
1.319
1.319
1.575
1.575
1.575
1.575
1.575
1.575
1.732
1.732
1.732
2.047
2.126
2.126
2.126
2.520
2.520
2.520
2.520
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.787
0.787
0.787
0.787
0.787
0.787
0.787
0.945
0.945
0.945
0.945
0.945
0.945
1.024
1.024
1.024
1.339
1.339
1.339
1.339
1.732
1.732
1.732
1.732
1.339
1.339
1.339
1.339
1.339
1.339
1.339
1.339
1.339
1.339
1.339
1.339
1.614
1.614
1.614
1.614
1.614
1.614
1.614
1.969
1.969
1.969
1.969
1.969
1.969
2.205
2.205
2.205
2.520
2.677
2.677
2.677
3.071
3.071
3.071
3.071
7,242
7,242
7,242
7,242
7,242
7,242
7,242
7,242
9,656
9,656
9,656
9,656
17,866
17,866
17,866
17,866
17,866
17,866
17,866
29,466
29,466
29,466
36,832
36,832
36,832
43,544
43,544
48,987
65,316
65,743
73,047
87,657
87,657
87,657
109,571
109,571
214
226
238
261
285
297
333
356
507
554
602
634
1,231
1,319
1,407
1,465
1,612
1,758
1,905
3,384
3,625
3,867
5,136
5,438
5,740
7,143
7,857
9,643
13,929
15,098
17,974
23,007
24,445
25,883
34,151
35,948
16,328
16,328
16,328
16,328
15,348
15,348
13,953
13,953
17,054
17,054
15,742
15,742
21,455
21,455
20,114
20,114
18,931
17,880
16,939
20,106
19,232
18,431
22,117
21,266
20,479
20,807
19,464
20,570
19,226
18,333
19,351
22,116
15,950
15,271
17,944
17,254
28,991
27,465
26,092
23,720
21,743
20,874
18,637
17,395
21,743
19,880
18,310
17,395
25,542
23,839
22,349
21,455
19,505
17,880
16,504
21,064
19,659
18,431
21,683
20,479
19,401
19,610
17,827
18,384
18,856
16,919
17,545
19,738
15,481
14,621
17,314
16,449
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
8
8
8
8
8
10
10
10
8
8
9
12
9
10
12
12
12
15
15
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M8
M8
M8
M8
M8
M8
M8
M10
M10
M10
M10
M10
M10
M12
M12
M12
M12
M14
M14
M14
M14
M14
M14
M14
10
10
10
10
10
10
10
10
10
10
10
10
26
26
26
26
26
26
26
52
52
52
52
52
52
85
85
85
85
136
136
136
136
136
136
136
439
ED
SLD
R
VSD
UJ
SP
T
D
GD
HP
G
psi
SLD-15
ED
psi
SLD
ft-lb
R
lbf
VSD
www.lovejoy-inc.com
-0 +0.0032
in
UJ
+0 -0.0028
-0 +0.0028
pS
in
SP
+0 -0.0025
-0 +0.0025
pH
in
T
+0 -0.0021
-0 +0.0021
Mt
in
D
+0 -0.0018
-0 +0.0018
F
in
GD
+0 -0.0015
-0 +0.0015
Locking Screws
HP
+0 -0.0013
1.850
1.850
1.850
1.850
1.969
1.969
2.165
2.165
2.362
2.362
2.559
2.559
2.953
2.953
3.150
3.150
3.346
3.543
3.740
4.331
4.528
4.724
4.921
5.118
5.315
5.709
6.102
6.496
7.087
7.480
7.874
8.268
8.858
9.252
9.843
10.236
T2
in
Pressures
G
0.709
0.748
0.787
0.866
0.945
0.984
1.102
1.181
1.260
1.378
1.496
1.575
1.654
1.772
1.890
1.969
2.165
2.362
2.559
2.756
2.953
3.150
3.347
3.543
3.740
3.937
4.331
4.724
5.118
5.512
5.906
6.299
6.693
7.087
7.480
7.874
in
Max
MC
D1
MC
18x47
19x47
20x47
22x47
24x50
25x50
28x55
30x55
32x60
35x60
38x65
40x65
42x75
45x75
48x80
50x80
55x85
60x90
65x95
70x110
75x115
80x120
85x125
90x130
95x135
100x145
110x155
120x165
130x180
140x190
150x200
160x210
170x225
180x235
190x250
200x260
T1
in
SF
in
CJ
D
Max
Size
JIS
SLD 1750 Metric Series Dimensional Data
d
JW
L
B
A
l
T
MA
D
D1
d
F
Mt
pH
pS
T1
T2
Shaft Locking Devices
SLD 1350 Inch Series
CJ
JIS
CJ
= total width (relaxed state)
= width of thrust rings (relaxed state)
= length of contact
= locking screw specifications
= screw tightening torque
= outer diameter of shaft locking device
= shaft diameter
= maximum transmissible axial force
= maximum transmissible torque
= pressure on the hub
= pressure on the shaft
= tolerance of shaft
= tolerance of hub bore
JIS
SLD 1350 Inch Series Dimensional Data
SF
SF
L
B
l
T
MA
D
d
F
Mt
pH
pS
T1
T2
JW
JW
Dimensional Data
d
MC
MC
0.750
GD
D
T
SP
-0 +0.0015
Max
F
Mt
lbf
ft-lb
Pressures
pH
Locking Screws
pS
in
in
in
psi
psi
Qty
Size
MA
ft-lb
1.102
0.669
1.339
8,733
273
18,710
34,954
6
M6
10
1.102
0.669
1.339
8,659
316
18,710
30,168
6
M6
10
1.969
1.102
0.669
1.339
8,603
358
17,550
26,542
6
M6
10
2.165
1.102
0.669
1.339
8,874
416
15,954
22,916
6
M6
10
1.188
2.165
1.102
0.669
1.339
8,705
431
15,954
22,191
6
M6
10
1-1/4
1.250
2.362
1.102
0.669
1.339
11,754
612
19,580
27,702
8
M6
10
1-3/8
1.375
2.362
1.102
0.669
1.339
11,689
670
19,580
25,382
8
M6
10
1-3/16
1.438
1.102
0.669
1.339
11,822
708
18,130
23,931
8
M6
10
1.102
0.669
1.339
11,636
727
18,130
23,351
8
M6
10
1.625
2.953
1.299
0.787
1.614
22,211
1,504
25,527
34,519
8
M8
26
1.688
2.953
1.299
0.787
1.614
22,427
1,557
25,527
32,924
8
M8
26
1-3/4
1.750
2.953
1.299
0.787
1.614
22,132
1,614
25,527
32,198
8
M8
26
1-7/8
1.875
3.150
1.319
0.787
1.614
22,535
1,761
23,931
29,588
8
M8
26
1-15/16
1-1/2
1.500
1-5/8
1-11/16
2.559
-0 +0.0018
2.559
1-7/16
+0 -0.0016
1.938
3.150
1.319
0.787
1.614
22,265
1,797
23,931
28,863
8
M8
26
2
2.000
3.150
1.319
0.787
1.614
22,445
1,870
23,931
27,847
8
M8
26
2-1/8
2.125
3.346
1.319
0.787
1.614
22,375
1,981
22,481
26,252
8
M8
26
2-3/16
2.188
3.346
1.319
0.787
1.614
22,537
2,054
22,481
25,237
8
M8
26
2.250
3.543
1.319
0.787
1.614
22,304
2,091
21,321
24,802
8
M8
26
2-3/8
2.375
3.543
1.319
0.787
1.614
22,241
2,201
21,321
23,641
8
M8
26
2-7/16
2.438
3.740
1.319
0.787
1.614
22,389
2,274
20,160
22,916
8
M8
26
3.740
1.319
0.787
1.614
22,538
2,348
20,160
22,191
8
M8
26
2-1/4
2-1/2
UJ
UJ
1.850
Max
1.125
SP
2.500
+0 -0.0018
-0+ 0.0022
2-9/16
2.563
3.740
1.319
0.787
1.614
22,333
2,385
20,160
21,756
8
M8
26
2-11/16
2.688
4.331
1.575
0.945
1.969
36,292
4,064
23,641
28,282
8
M10
52
2.750
4.331
1.575
0.945
1.969
36,510
4,183
23,641
27,557
8
M10
52
2.875
4.528
1.575
0.945
1.969
36,425
4,363
22,626
26,397
8
M10
52
2-15/16
2.938
4.528
1.575
0.945
1.969
36,626
4,483
22,626
25,672
8
M10
52
3
3.000
4.724
1.575
0.945
1.969
36,341
4,543
21,611
25,382
8
M10
52
3-1/4
3.250
4.921
1.575
0.945
1.969
45,790
6,201
25,962
29,008
10
M10
52
3-3/8
3.375
4.921
1.575
0.945
1.969
45,688
6,425
25,962
27,992
10
M10
52
3-7/16
3.438
1.575
0.945
1.969
45,378
6,499
24,947
27,702
10
M10
52
1.575
0.945
1.969
45,594
6,649
24,947
26,977
10
M10
52
2-3/4
2-7/8
R
SLD
3-1/2
VSD
VSD
+0 -0.0013
T
1.000
T
R
in
1.850
T2
in
L
l
1-1/8
D
SLD
0.875
T1
in
B
1
GD
3.500
+0 -0.0022
5.118
5.118
-0 +0.0025
3-3/4
3.750
5.315
1.575
0.945
1.969
45,424
7,098
24,076
25,382
10
M10
52
3-15/16
3.938
5.709
1.732
1.024
2.205
50,625
8,306
22,916
26,687
8
M12
85
4.000
5.709
1.732
1.024
2.205
50,830
8,472
22,916
26,252
8
M12
85
4
ED
ED
7/8
HP
HP
G
in
3/4
G
Size
D
SLD-16
440
630-852-0500
Shaft Locking Devices
SLD 1350 Metric Series
Dimensional Data
JW
= total width (relaxed state)
= width of thrust rings (relaxed state)
= length of contact
= locking screw specifications
= screw tightening torque
= outer diameter of shaft locking device
= shaft diameter
= maximum transmissible axial force
= maximum transmissible torque
= pressure on the hub
= pressure on the shaft
= tolerance of shaft
= tolerance of hub bore
JW
JIS
JIS
CJ
CJ
L
B
l
T
MA
D
d
F
Mt
pH
pS
T1
T2
SLD 1350 Metric Series Dimensional Data
L
l
T
Max
T1
in
in
T2
in
in
in
in
F
Mt
pH
pS
lbf
ft-lb
psi
psi
Locking Screws
Qty
Size
MA
ft-lb
0.709
1.850
1.102
0.669
1.339
8,780
259
18,710
36,985
6
M6
10
19x47
0.748
1.850
1.102
0.669
1.339
8,790
274
18,710
34,954
6
M6
10
0.787
1.850
1.102
0.669
1.339
8,308
273
18,710
33,214
6
0.866
1.850
1.102
0.669
1.339
8,310
300
18,710
30,168
6
24x50
0.945
1.102
0.669
1.339
8,311
327
17,550
27,702
6
M6
10
25x50
0.984
1.102
0.669
1.339
8,304
341
17,550
26,542
6
M6
10
+0 -0.0013
1.969
-0 +0.0015
1.102
2.165
1.102
0.669
1.339
8,314
382
15,954
23,786
6
M6
10
30x55
1.181
2.165
1.102
0.669
1.339
8,315
409
15,954
22,191
6
M6
10
32x60
1.260
2.362
1.102
0.669
1.339
11,079
582
19,580
27,702
8
M6
10
35x60
1.378
2.362
1.102
0.669
1.339
11,081
636
19,580
25,382
8
M6
10
38x65
1.496
2.559
1.102
0.669
1.339
11,083
691
18,130
23,351
8
M6
10
+0 -0.0015
2.559
2.953
-0 +0.0018
1.102
0.669
1.339
11,074
727
18,130
22,191
8
M6
10
1.299
0.787
1.614
21,245
1,464
25,527
30,748
8
M8
26
D
1.575
1.654
2.953
1.299
0.787
1.614
21,243
1,568
25,527
31,473
8
M8
26
3.150
1.319
0.787
1.614
21,241
1,673
23,931
29,588
8
M8
26
50x80
1.969
3.150
1.319
0.787
1.614
21,246
1,743
23,931
28,282
8
M8
26
55x85
2.165
3.346
1.319
0.787
1.614
21,240
1,916
22,481
25,817
8
M8
26
60x90
2.362
3.543
1.319
0.787
1.614
21,243
2,091
21,321
23,641
8
M8
26
+0 -0.0018
3.740
4.331
-0 +0.0021
1.319
0.787
1.614
21,245
2,265
20,160
21,756
8
1.575
0.945
1.969
34,610
3,974
23,641
27,557
8
M8
26
M10
52
SP
2.559
2.756
4.528
1.575
0.945
1.969
34,615
4,259
22,626
25,672
8
M10
52
4.724
1.575
0.945
1.969
34,614
4,543
21,611
24,076
8
M10
52
85x125
3.346
4.921
1.575
0.945
1.969
43,266
6,033
25,962
28,282
10
M10
52
90x130
3.543
5.118
1.575
0.945
1.969
43,264
6,387
24,947
26,687
10
M10
52
1.969
43,267
6,743
24,076
25,382
10
M10
48,100
7,890
22,916
26,687
8
VSD
52
2.205
M12
85
6.102
1.732
1.024
2.205
48,100
8,679
21,466
21,901
8
M12
85
120x165
130x180
4.724
6.496
1.732
1.024
2.205
54,115
10,652
22,771
22,626
9
M12
85
5.118
7.087
2.047
1.339
2.520
72,150
15,386
21,176
23,206
12
M12
85
140x190
5.512
7.480
2.126
1.339
2.677
73,654
16,915
20,595
21,031
9
M14
136
150x200
5.906
7.874
2.126
1.339
2.677
81,837
20,137
21,611
21,901
10
M14
136
160x210
6.299
2.126
1.339
2.677
98,204
25,775
24,802
24,511
12
M14
136
+0 -0.0025
8.268
170x225
6.693
8.858
180x235
7.087
9.252
7.480
7.874
+0 -0.0028
9.843
10.236
www.lovejoy-inc.com
-0 +0.0032
2.520
1.732
3.071
98,204
27,386
17,840
19,290
12
M14
136
2.520
1.732
3.071
98,204
28,997
17,114
18,130
12
M14
136
2.520
1.732
3.071
122,755
38,260
20,160
21,611
15
M14
136
2.520
1.732
3.071
122,755
40,274
19,290
20,450
15
M14
136
441
SLD-17
ED
190x250
200x260
-0 +0.0028
SLD
4.331
R
0.945
1.024
-0 +0.0025
ED
110x155
5.315
5.709
SLD
1.575
1.732
+0 -0.0021
R
3.740
3.937
VSD
95x135
100x145
UJ
2.953
3.150
UJ
75x115
80x120
SP
65x95
70X110
T
1.772
1.890
T
45x75
48x80
D
40x65
42x75
GD
28x55
HP
10
10
GD
1.969
M6
M6
HP
20x47
22x47
G
18x47
G
in
Pressures
MC
Size
Max
SF
B
MC
D
SF
d
Shaft Locking Devices
SLD 1450 Inch Series
JIS
CJ
CJ
SLD 1450 Inch Series Dimensional Data
SF
SF
= total width (relaxed state)
= width of thrust rings (relaxed state)
= width to flange
= length of contact
= locking screw specifications
= screw tightening torque
= outer diameter of shaft locking device
= diameter to flange
= shaft diameter
= maximum transmissible axial force
= maximum transmissible torque
= pressure on the hub
= pressure on the shaft
= tolerance of shaft
= tolerance of hub bore
JIS
L
B
A
l
T
MA
D
D1
d
F
Mt
pH
pS
T1
T2
JW
JW
Dimensional Data
d
HP
0.750
7/8
D
T
Max
Max
F
Mt
ft-lb
Pressures
pH
pS
psi
psi
Locking Screws
Qty
Size
MA
ft-lb
in
in
in
in
in
lbf
2.204
0.866
1.102
0.669
1.339
7,242
226
14,739 24,723
6
M6
12
2.204
0.866
1.102
0.669
1.339
7,242
264
14,739 21,191
6
M6
12
12
2.323
0.866
1.102
0.669
1.339
7,242
302
13,848 18,542
6
M6
2.519
0.866
1.102
0.669
1.339
7,242
339
12,595 16,482
6
M6
12
1.188
2.165
2.519
0.866
1.102
0.669
1.339
7,242
358
12,595 15,614
6
M6
12
1-3/16
1-1/4
1.250
2.362
2.716
0.866
1.102
0.669
1.339
9,656
503
15,392 19,778
8
M6
12
1-3/8
1.375
2.362
2.716
0.866
1.102
0.669
1.339
9,656
553
15,392 17,980
8
M6
12
1.438
2.559
1-7/16
1.500
+0 -0.0016
-0 +0.0018
2.559
2.913
0.866
1.102
0.669
1.339
9,656
578
14,207 17,198
8
M6
12
2.913
0.866
1.102
0.669
1.339
9,656
604
14,207 16,482
8
M6
12
1-5/8
1.625
2.953
3.307
0.984
1.299
0.787
1.614
17,866
1,210
19,362 23,457
8
M8
29
1-11/16
1.688
2.953
3.307
0.984
1.299
0.787
1.614
17,866
1,256
19,362 22,588
8
M8
29
1-3/4
1.750
2.953
3.307
0.984
1.299
0.787
1.614
17,866
1,303
19,362 21,781
8
M8
29
1-7/8
1.875
3.150
3.504
0.945
1.319
0.787
1.614
17,866
1,396
18,151 20,329
8
M8
29
1-15/16
T
1.938
3.150
3.504
0.945
1.319
0.787
1.614
17,866
1,442
18,151 19,673
8
M8
29
2.000
3.150
3.504
0.945
1.319
0.787
1.614
17,866
1,489
18,153 19,059
8
M8
29
2-1/8
2.125
3.346
3.700
0.945
1.319
0.787
1.614
17,866
1,582
17,088 17,938
8
M8
29
2-3/16
2.188
3.346
3.700
0.945
1.319
0.787
1.614
17,866
1,628
17,088 17,425
8
M8
29
2.250
3.543
3.897
0.945
1.319
0.787
1.614
17,866
1,675
16,138 16,941
8
M8
29
2-1/4
SP
SP
T
2.165
D
2-3/8
2.375
3.543
2-7/16
2.438
3.740
UJ
UJ
-0 +0.0015
L
1.969
GD
+0 -0.0018
3.897
0.945
1.319
0.787
1.614
17,866
1,768
16,138 16,049
8
M8
29
4.094
0.945
1.319
0.787
1.614
17,866
1,814
15,288 15,638
8
M8
29
3.740
4.094
0.945
1.319
0.787
1.614
17,866
1,861
15,288 15,247
8
M8
29
2.563
3.740
4.094
0.945
1.319
0.787
1.614
17,866
1,908
15,288 14,875
8
M8
29
2-11/16
2.688
4.331
4.685
1.142
1.575
0.945
1.969
29,466
3,300
18,145 19,494
8
M10
58
1.969
29,466
3,376
18,145 19,051
8
M10
58
2-1/2
2-3/4
2-7/8
2.500
-0 +0.0022
2-9/16
VSD
VSD
1.850
l
1.000
2-15/16
2.750
4.331
4.685
1.142
1.575
0.945
2.875
4.528
4.882
1.142
1.575
0.945
1.969
29,466
3,530
17,355 18,222
8
M10
58
2.938
4.528
4.882
1.142
1.575
0.945
1.969
29,466
3,607
17,355 17,835
8
M10
58
3.000
4.724
5.078
1.142
1.575
0.945
1.969
29,466
3,683
16,635 17,463
8
M10
58
3-1/4
3.250
4.921
5.275
1.142
1.575
0.945
1.969
29,466
3,990
15,969 16,120
8
M10
58
3-3/8
3.375
4.921
5.275
1.142
1.575
0.945
1.969
36,832
5,180
19,962 19,404
10
M10
58
3
SLD
3-7/16
3-1/2
R
R
+0 -0.0013
B
1.125
2
SLD
in
1.850
T2
in
A
1
1-1/2
3.438
3.500
5.118
+0 -0.0022
5.118
-0 +0.0025
5.470
1.142
1.575
0.945
1.969
36,832
5,275
19,193 19,051
10
M10
58
5.470
1.142
1.575
0.945
1.969
36,832
5,371
19,193 18,711
10
M10
58
3-3/4
3.750
5.315
5.669
1.142
1.575
0.945
1.969
36,832
5,755
18,482 17,463
10
M10
58
3-15/16
3.938
5.708
6.603
1.220
1.732
1.024
2.205
43,544
7,144
18,780 17,696
8
M12
102
4.000
5.709
6.603
1.220
1.732
1.024
2.205
43,544
7,257
18,778 17,419
8
M12
102
4
ED
ED
0.875
T1
in
D1
1-1/8
HP
GD
in
3/4
G
G
MC
MC
Size
D
SLD-18
442
630-852-0500
Shaft Locking Devices
SLD 1450 Metric Series
Dimensional Data
JW
= total width (relaxed state)
= width of thrust rings (relaxed state)
= width to flange
= length of contact
= locking screw specifications
= screw tightening torque
= outer diameter of shaft locking device
= diameter to flange
= shaft diameter
= maximum transmissible axial force
= maximum transmissible torque
= pressure on the hub
= pressure on the shaft
= tolerance of shaft
= tolerance of hub bore
JIS
CJ
SF
MC
Pressures
Locking Screws
pS
443
G
Size
HP
M6
M6
M6
M6
M6
M6
M6
M6
M8
M8
M8
M8
M8
M8
M8
M8
M8
M8
M8
M10
M10
M10
M10
M10
M10
M12
M12
M12
M12
M14
M14
M14
M14
M14
M14
M14
GD
6
6
6
6
6
6
6
6
8
8
8
8
8
8
8
8
8
8
8
8
8
8
10
10
10
8
8
9
12
9
10
12
12
12
15
15
D
Qty
27,542
26,092
24,788
22,534
20,656
19,830
17,705
16,525
20,656
18,886
17,395
16,525
24,265
22,647
21,232
20,383
18,530
16,986
15,679
20,010
18,676
17,509
20,599
19,455
18,431
18,630
16,936
17,465
17,913
16,073
16,668
18,751
14,707
13,890
16,449
15,626
T
psi
15,512
15,512
15,512
15,512
14,581
14,581
13,255
13,255
16,201
16,201
14,955
14,955
20,383
20,383
19,109
19,109
17,985
16,986
16,092
19,101
18,270
17,509
21,011
20,203
19,455
19,766
18,491
19,542
18,264
17,416
18,384
21,010
15,153
14,508
17,047
16,391
SP
psi
203
214
226
248
271
282
316
339
482
527
572
602
1,169
1,253
1,336
1,392
1,531
1,670
1,810
3,214
3,444
3,674
4,879
5,166
5,453
6,786
7,464
9,161
13,232
14,343
17,076
21,857
24,445
24,589
32,443
34,151
UJ
ft-lb
VSD
lbf
6,880
6,880
6,880
6,880
6,880
6,880
6,880
6,880
9,173
9,173
9,173
9,173
16,972
16,972
16,972
16,972
16,972
16,972
16,972
27,993
27,993
27,993
34,991
34,991
34,991
41,367
41,367
46,538
62,050
62,455
69,395
83,274
87,657
83,274
104,092
104,092
R
in
1.339
1.339
1.339
1.339
1.339
1.339
1.339
1.339
1.339
1.339
1.339
1.339
1.614
1.614
1.614
1.614
1.614
1.614
1.614
1.969
1.969
1.969
1.969
1.969
1.969
2.205
2.205
2.205
2.205
2.677
2.677
2.677
3.071
3.071
3.071
3.071
12
12
12
12
12
12
12
12
29
29
29
29
29
29
29
29
29
29
29
58
58
58
58
58
58
102
102
102
102
161
161
161
161
161
161
161
SLD-19
ED
in
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.669
0.787
0.787
0.787
0.787
0.787
0.787
0.787
0.945
0.945
0.945
0.945
0.945
0.945
1.024
1.024
1.024
1.339
1.339
1.339
1.339
1.732
1.732
1.732
1.732
SLD
in
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.299
1.299
1.319
1.319
1.319
1.319
1.319
1.575
1.575
1.575
1.575
1.575
1.575
1.732
1.732
1.732
2.047
2.126
2.126
2.126
2.520
2.520
2.520
2.520
R
in
0.866
0.866
0.866
0.866
0.866
0.866
0.866
0.866
0.866
0.866
0.866
0.866
0.984
0.984
0.945
0.945
0.945
0.945
0.945
1.142
1.142
1.142
1.142
1.142
1.142
1.220
1.220
1.220
1.535
1.535
1.535
1.535
1.929
1.929
1.929
1.929
MA
ft-lb
VSD
in
2.205
2.205
2.205
2.205
2.323
2.323
2.520
2.520
2.717
2.717
2.913
2.913
3.307
3.307
3.504
3.504
3.701
3.898
4.094
4.685
4.882
5.079
5.276
5.472
5.669
6.063
6.457
6.850
7.441
7.835
8.228
8.622
9.213
9.606
10.197
10.591
SLD
pH
ED
Mt
UJ
www.lovejoy-inc.com
-0 +0.0032
Max
F
SP
+0 -0.0028
-0 +0.0028
Max
T
+0 -0.0025
-0 +0.0025
T
D
+0 -0.0021
-0 +0.0021
L
GD
+0 -0.0018
-0 +0.0018
l
HP
+0 -0.0015
-0 +0.0015
B
G
+0 -0.0013
in
1.850
1.850
1.850
1.850
1.969
1.969
2.165
2.165
2.362
2.362
2.559
2.559
2.953
2.953
3.150
3.150
3.346
3.543
3.740
4.331
4.528
4.724
4.921
5.118
5.315
5.709
6.102
6.496
7.087
7.480
7.874
8.268
8.858
9.252
9.843
10.236
A
MC
0.709
0.748
0.787
0.866
0.945
0.984
1.102
1.181
1.260
1.378
1.496
1.575
1.654
1.772
1.890
1.969
2.165
2.362
2.559
2.756
2.953
3.150
3.347
3.543
3.740
3.937
4.331
4.724
5.118
5.512
5.906
6.299
6.693
7.087
7.480
7.874
D1
T2
in
SF
in
18x47
19x47
20x47
22x47
24x50
25x50
28x55
30x55
32x60
35x60
38x65
40x65
42x75
45x75
48x80
50x80
55x85
60x90
65x95
70x110
75x115
80x120
85x125
90x130
95x135
100x145
110x155
120x165
130x180
140x190
150x200
160x210
170x225
180X235
190x250
200x260
CJ
Size
D
T1
in
JIS
SLD 1450 Metric Series Dimensional Data
d
JW
L
B
A
l
T
MA
D
D1
d
F
Mt
pH
pS
T1
T2
Shaft Locking Devices
SLD 2600 Inch Series
JIS
CJ
CJ
SLD 2600 Inch Series Dimensional Data
SF
SF
= total width (relaxed state)
= width of thrust rings (relaxed state)
= length of contact
= locking screw specifications
= screw tightening torque
= outer diameter of shaft locking device
= shaft diameter
= maximum transmissible axial force
= maximum transmissible torque
= pressure on the hub
= pressure on the shaft
= tolerance of shaft
= tolerance of hub bore
JIS
L
B
l
T
MA
D
d
F
Mt
pH
pS
T1
T2
JW
JW
Dimensional Data
d
D
B
l
L
T
G
HP
GD
D
T
SP
+0 -0.0018
SP
UJ
UJ
+0 -0.0015
T
+0 -0.0021
VSD
VSD
+0 -0.0013
D
R
R
T1
in
GD
SLD
SLD
HP
ED
1
1-1/8
1-3/16
1-1/4
1-3/8
1-7/16
1-1/2
1-5/8
1-3/4
1-7/8
1-15/16
2
2-1/8
2-3/16
2-1/4
2-3/8
2-7/16
2-1/2
2-9/16
2-5/8
2-11/16
2-3/4
2-7/8
2-15/16
3
3-1/8
3-1/4
3-3/8
3-7/16
3-1/2
3-5/8
3-3/4
3-7/8
3-15/16
4
4-1/4
4-3/8
4-7/16
4-1/2
4-3/4
4-15/16
5
5-1/4
5-7/16
5-1/2
5-3/4
5-15/16
6
6-7/16
6-1/2
in
1.000
1.125
1.188
1.250
1.375
1.438
1.500
1.625
1.750
1.875
1.938
2.000
2.125
2.188
2.250
2.375
2.438
2.500
2.563
2.625
2.688
2.750
2.875
2.938
3.000
3.125
3.250
3.375
3.438
3.500
3.625
3.750
3.875
3.938
4.000
4.250
4.375
4.438
4.500
4.750
4.938
5.000
5.250
5.438
5.500
5.750
5.938
6.000
6.438
6.500
G
ED
Size
MC
MC
Max
SLD-20
+0 -0.0025
in
1.969
2.165
2.165
2.362
2.362
2.362
2.559
2.559
2.953
3.150
3.150
3.150
3.346
3.346
3.543
3.543
3.740
3.740
3.740
4.331
4.331
4.331
4.331
4.724
4.724
4.724
4.724
5.118
5.118
5.118
5.118
5.709
5.709
5.709
5.709
6.102
6.102
6.496
6.496
6.496
7.087
7.087
7.480
7.480
7.480
7.874
7.874
8.268
8.858
8.858
T2
in
-0 +0.0018
-0 +0.0021
-0 0.0025
-0 +0.0028
in
1.772
1.772
1.772
1.772
1.772
1.772
1.772
1.772
1.772
2.520
2.520
2.520
2.520
2.520
2.520
2.520
2.520
2.520
2.520
3.071
3.071
3.071
3.071
3.071
3.071
3.071
3.071
3.071
3.071
3.071
3.071
3.937
3.937
3.937
3.937
3.937
3.937
3.937
3.937
3.937
4.567
4.567
4.567
4.567
4.567
4.567
4.567
4.567
5.748
5.748
in
1.614
1.614
1.614
1.614
1.614
1.614
1.614
1.614
1.614
2.205
2.205
2.205
2.205
2.205
2.205
2.205
2.205
2.205
2.205
2.756
2.756
2.756
2.756
2.756
2.756
2.756
2.756
2.756
2.756
2.756
2.756
3.543
3.543
3.543
3.543
3.543
3.543
3.543
3.543
3.543
4.094
4.094
4.094
4.094
4.094
4.094
4.094
4.094
5.276
5.276
in
2.008
2.008
2.008
2.008
2.008
2.008
2.008
2.008
2.008
2.835
2.835
2.835
2.835
2.835
2.835
2.835
2.835
2.835
2.835
3.465
3.465
3.465
3.465
3.465
3.465
3.465
3.465
3.465
3.465
3.465
3.465
4.409
4.409
4.409
4.409
4.409
4.409
4.409
4.409
4.409
5.118
5.118
5.118
5.118
5.118
5.118
5.118
5.118
6.378
6.378
444
Max
Pressures
F
Mt
pH
pS
lbf
12,965
19,447
18,247
18,196
19,015
18,072
22,547
23,408
34,443
34,267
33,049
33,014
33,981
32,923
41,120
42,199
41,030
41,003
40,978
67,545
67,507
67,470
68,934
80,844
80,808
82,421
82,289
82,167
80,589
80,563
81,950
120,959
120,824
118,813
118,783
124,235
120,366
138,363
138,336
143,993
163,115
158,907
192,228
189,613
185,179
218,739
216,051
211,431
308,120
289,968
ft-lb
540
810
855
900
990
1,035
1,350
1,463
2,332
2,499
2,582
2,665
2,832
2,915
3,748
3,956
4,060
4,164
4,268
7,212
7,384
7,555
7,899
9,684
9,891
10,303
10,715
11,127
11,333
11,539
11,951
18,270
18,879
19,183
19,488
20,706
21,315
25,223
25,578
26,999
32,283
32,692
40,048
41,478
41,955
50,128
51,762
52,307
77,030
77,778
psi
12,022
14,579
14,579
13,363
13,363
13,363
15,418
15,418
19,775
13,573
13,573
13,573
12,778
12,778
15,084
15,084
14,290
14,290
14,290
16,282
16,282
16,282
16,282
17,913
17,913
17,913
17,913
16,534
16,534
16,534
16,534
17,036
17,036
17,036
17,036
15,939
15,939
17,468
17,468
17,468
15,938
15,938
17,618
17,618
17,618
19,127
19,127
18,216
18,112
18,112
psi
24,886
29,495
27,942
26,545
24,132
23,083
27,651
25,524
35,081
27,760
26,864
26,025
24,494
23,794
28,916
27,394
26,692
26,025
25,390
33,579
32,798
32,053
30,659
36,008
35,258
33,848
32,546
31,341
30,771
30,221
29,179
33,346
32,270
31,758
31,262
29,423
28,582
32,876
32,420
30,714
29,015
28,652
31,836
30,738
30,389
33,220
32,171
31,836
32,112
31,803
Locking Screws
Qty
6
8
8
8
8
8
10
10
8
8
8
8
8
8
10
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
12
12
12
12
14
14
14
12
12
14
14
14
16
16
16
16
16
Size
M6
M6
M6
M6
M6
M6
M6
M6
M8
M8
M8
M8
M8
M8
M8
M8
M8
M8
M8
M10
M10
M10
M10
M10
M10
M10
M10
M10
M10
M10
M10
M12
M12
M12
M12
M12
M12
M12
M12
M12
M14
M14
M14
M14
M14
M14
M14
M14
M16
M16
MA
ft-lb
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
30.2
30.2
30.2
30.2
30.2
30.2
30.2
30.2
30.2
30.2
30.2
61.2
61.2
61.2
61.2
61.2
61.2
61.2
61.2
61.2
61.2
61.2
61.2
106.9
106.9
106.9
106.9
106.9
106.9
106.9
106.9
106.9
169.6
169.6
169.6
169.6
169.6
169.6
169.6
169.6
261.8
261.8
630-852-0500
Shaft Locking Devices
SLD 2600 Metric Series
Dimensional Data
JW
= total width (relaxed state)
= width of thrust rings (relaxed state)
= length of contact
= locking screw specifications
= screw tightening torque
= outer diameter of shaft locking device
= shaft diameter
= maximum transmissible axial force
= maximum transmissible torque
= pressure on the hub
= pressure on the shaft
= tolerance of shaft
= tolerance of hub bore
JIS
CJ
CJ
T2
in
in
SF
L
l
T
Max
Max
F
Mt
ft-lb
Pressures
pH
Locking Screws
pS
MA
in
lbf
psi
psi
Qty
Size
ft-lb
1.614
2.008
12,965
532
12,026
25,284
6
M6
12.5
2.165
1.772
1.614
2.008
20,744
851
14,576
28,094
8
M6
12.5
2.362
1.772
1.614
2.008
18,439
907
13,362
26,338
8
M6
12.5
1.772
1.614
2.008
18,907
992
13,362
24,080
8
M6
12.5
1.772
1.614
2.008
24,695
1,418
16,702
26,338
10
1.772
1.614
2.008
35,980
2,361
19,777
34,652
8
1.378
2.362
40x65
1.575
2.559
45x75
1.772
2.953
50x80
1.969
3.150
2.520
2.283
2.835
35,536
2,623
13,107
26,441
8
55x85
2.165
3.346
2.520
2.283
2.835
35,181
2,886
12,336
24,037
8
60x90
2.362
3.543
2.520
2.283
2.835
43,612
3,935
14,563
27,543
65x95
2.559
3.740
2.520
2.283
2.835
43,310
4,263
13,796
25,424
70x110
2.756
3.071
2.756
3.465
71,009
7,571
16,283
31,984
10
M10
61.2
75x115
2.953
4.528
3.071
2.756
3.465
70,646
8,112
15,575
29,852
10
M10
61.2
80x120
3.150
4.724
3.071
2.756
3.465
84,399
10,384
17,911
33,583
12
M10
61.2
85x125
3.346
4.921
3.071
2.756
3.465
84,069
11,033
17,195
31,608
12
M10
61.2
90x130
3.543
5.118
3.071
2.756
3.465
83,778
11,682
16,533
29,852
12
M10
61.2
3.071
2.756
3.465
83,520
12,331
15,804
28,281
12
3.622
4.409
123,081
19,181
16,667
31,762
12
6.102
3.937
3.622
4.409
128,620
21,099
15,592
28,875
6.496
3.937
3.622
4.409
148,816
26,853
17,088
30,880
140x190
5.118
7.087
4.567
4.252
5.118
169,998
33,464
15,349
27,991
12
5.512
7.480
4.567
4.252
5.118
197,157
42,045
16,965
30,324
14
150x200
5.906
7.874
4.567
4.252
5.118
224,173
51,483
18,419
32,345
16
160x210
6.299
170x225
6.693
8.858
4.567
4.252
5.118
223,177
54,916
17,542
30,324
16
5.748
5.354
6.378
266,987
70,075
15,615
27,026
14
180x235
7.087
190x250
7.480
9.252
5.748
5.354
6.378
304,072
84,797
17,086
29,170
16
9.843
5.748
5.354
6.378
303,134
89,508
16,061
27,635
16
200x260
7.874
220x285
8.661
240x305
9.449
+0 -0.0025
8.268
-0 +0.0025
-0 +0.0028
10.236
11.220
12.008
-0 +0.0032
HP
GD
D
T
M10
61.2
M12
106.9
12
M12
106.9
14
M12
106.9
M14
169.6
M14
169.6
5.748
5.354
6.378
302,294
94,219
15,443
26,253
16
5.748
5.354
6.378
394,872
129,551
17,611
29,833
20
5.748
5.354
6.378
430,769
155,461
18,101
30,082
22
M14
169.6
M14
169.6
M16
261.8
M16
261.8
M16
261.8
M16
261.8
M16
261.8
M16
261.8
www.lovejoy-inc.com
445
SLD-21
ED
ED
+0 -0.0028
5.709
SP
130x180
30.2
UJ
4.724
30.2
M8
SLD
4.331
M8
10
R
110x155
120x165
10
3.937
+0 -0.0021
5.315
30.2
30.2
VSD
3.937
M8
M8
UJ
3.740
30.2
SP
95x135
100x145
M8
VSD
4.331
-0 +0.0021
12.5
R
+0 -0.0018
M6
SLD
+0 -0.0015
-0 +0.0018
G
35x60
+0 -0.0013
T
1.260
D
1.181
32x60
GD
30x55
HP
in
1.772
0.984
G
in
1.969
25x50
MC
T1
in
B
MC
D
SF
d
in
JIS
SLD 2600 Metric Series Dimensional Data
Size
JW
L
B
l
T
MA
D
d
F
Mt
pH
pS
T1
T2
Shaft Locking Devices
SLD 1900 Inch Series
JIS
CJ
CJ
SLD 1900 Inch Series Dimensional Data
SF
SF
= total width (relaxed state)
= width of thrust rings (relaxed state)
= length of contact
= locking screw specifications
= screw tightening torque
= outer diameter of shaft locking device
= diameter to flange
= shaft diameter
= maximum transmissible axial force
= maximum transmissible torque
= pressure on the hub
= pressure on the shaft
= tolerance of shaft
= tolerance of hub bore
JIS
L
B
l
T
MA
D
D1
d
F
Mt
pH
pS
T1
T2
JW
JW
Dimensional Data
d
D
D1
B
l
L
T
HP
GD
D
pH
pS
in
lbf
ft-lb
psi
psi
Qty
Size
MA
ft-lb
1.063
1.890
1.496
0.709
1.732
5,568
174
11,592
8,966
4
M6
12
1.260
2.126
1.772
0.984
2.008
6,496
203
7,419
6,675
4
M6
12
1.339
2.205
1.772
0.984
2.008
5,952
217
7,154
6,385
4
M6
12
1.339
2.205
1.772
0.984
2.008
5,939
232
7,154
5,985
4
M6
12
1.125
1.535
2.402
1.772
0.984
2.008
9,384
391
9,851
8,399
6
M6
12
1-3/16
1.188
1.614
2.441
1.772
0.984
2.008
8,811
413
9,692
8,231
6
M6
12
1-1/4
1.250
1.693
2.559
1.772
0.984
2.008
11,702
579
12,327
11,129
8
M6
12
1.375
1.850
2.717
1.969
1.181
2.205
12,230
637
9,677
8,679
8
M6
12
1.969
2.835
1.969
1.181
2.205
11,625
666
9,274
8,468
8
M6
12
1.969
2.835
1.969
1.181
2.205
11,603
695
9,274
8,115
8
M6
12
1-3/8
1-7/16
1.438
1-1/2
1.500
+0 -0.0016
-0 +0.0015
1.625
2.165
3.071
2.244
1.260
2.480
12,048
753
8,025
5,800
8
M6
12
1-11/16
1.688
2.323
3.346
2.559
1.575
2.874
18,447
1,249
9,414
8,787
8
M8
30
1-3/4
1.750
2.323
3.346
2.559
1.575
2.874
18,432
1,296
9,414
8,473
8
M8
30
1.875
2.441
3.425
2.756
1.772
3.071
19,035
1,388
8,176
8,120
8
M8
30
1-15/16
1.938
2.559
3.622
2.756
1.772
3.071
22,950
1,793
9,664
8,976
10
M8
30
2
2.000
2.795
3.858
2.953
1.969
3.071
22,929
1,851
8,165
8,917
10
M8
30
2.125
2.795
3.858
2.953
1.969
3.268
23,604
1,967
8,165
8,392
10
M8
30
2-3/16
2.188
3.031
4.094
2.953
1.969
3.268
22,859
2,024
7,694
8,331
10
M8
30
2-3/8
2.375
3.031
4.094
2.953
1.969
3.268
24,115
2,198
7,694
7,673
10
M8
30
3.307
4.370
2.953
1.969
3.268
22,797
2,256
7,209
7,643
10
M8
30
3.307
4.370
2.953
1.969
3.268
22,784
2,314
7,209
7,452
10
M8
30
4.685
3.583
2.362
3.976
37,997
3,958
9,131
10,716
10
M10
60
4.685
3.583
2.362
3.976
37,915
4,147
9,131
10,229
10
M10
60
2.362
3.976
37,833
4,335
8,623
8,012
10
M10
60
1-5/8
1-7/8
2-1/8
UJ
2-7/16
SP
2.438
2.500
VSD
VSD
Mt
in
1.000
1-1/8
T
+0 -0.0018
-0 +0.0018
2.625
3.543
2.750
3.543
2-7/8
2.875
3.740
4.961
3.583
2-15/16
2.938
3.740
4.961
3.583
2.362
3.976
36,981
4,430
8,623
7,841
10
M10
60
3.000
3.740
4.961
3.583
2.362
3.976
36,962
4,524
8,623
7,247
10
M10
60
2-5/8
2-3/4
R
R
F
in
1
3
-0 +0.0021
SLD
SLD
+0 -0.0013
Locking Screws
in
in
T2
in
Pressures
0.938
D
T
0.875
GD
SP
7/8
T1
in
Max
1-5/16
HP
UJ
0.750
2-1/2
ED
ED
in
3/4
G
G
Size
MC
MC
Max
SLD-22
446
630-852-0500
Shaft Locking Devices
SLD 1900 Metric Series
Dimensional Data
JW
= total width (relaxed state)
= width of thrust rings (relaxed state)
= length of contact
= locking screw specifications
= screw tightening torque
= outer diameter of shaft locking device
= diameter to flange
= shaft diameter
= maximum transmissible axial force
= maximum transmissible torque
= pressure on the hub
= pressure on the shaft
= tolerance of shaft
= tolerance of hub bore
JIS
CJ
SF
Locking Screws
MC
Pressures
ft-lb
psi
psi
Qty
Size
1,049
2,098
2,304
2,298
2,248
2,248
2,398
4,593
4,556
4,552
5,422
5,420
5,395
5,643
5,600
5,339
8,615
8,238
10,941
11,212
11,125
10,791
19,727
20,126
20,033
24,457
25,826
25,612
25,433
40,244
40,035
47,827
47,643
59,350
59,165
68,924
72,024
71,428
94,577
10
21
30
34
37
41
47
105
112
119
151
160
168
185
202
210
353
378
538
589
639
673
1,294
1,387
1,479
1,926
2,118
2,311
2,503
4,291
4,597
5,884
6,252
8,275
8,735
10,741
11,815
12,889
18,618
13,779
14,649
15,664
15,664
13,924
13,924
10,878
19,145
19,145
18,275
18,710
18,130
17,405
11,023
10,298
10,298
13,489
12,908
16,389
12,473
11,748
11,023
18,275
13,634
11,458
13,779
11,313
10,443
9,573
11,893
11,168
11,748
11,168
13,198
12,328
13,779
8,847
7,977
10,008
14,939
15,084
17,840
15,954
14,504
12,763
10,878
14,794
13,924
13,053
14,794
14,069
13,343
10,008
9,137
8,847
11,748
11,023
12,183
11,168
10,298
9,718
12,908
12,183
10,443
12,618
10,588
9,718
8,992
13,198
10,153
10,733
10,153
12,038
11,313
11,893
8,412
7,687
9,427
4
3
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
8
8
8
8
8
8
8
10
10
10
10
10
10
12
15
15
12
12
12
12
16
M3
M4
M4
M4
M4
M4
M4
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M6
M8
M8
M8
M8
M8
M8
M8
M10
M10
M10
M10
M10
M10
M12
M12
M12
M12
1.50
3.70
3.70
3.70
3.70
3.70
3.70
11.1
11.1
11.1
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
30.2
30.2
30.2
30.2
30.2
30.2
30.2
61.2
61.2
61.2
61.2
61.2
61.2
107
107
107
107
SLD
R
VSD
UJ
SP
T
D
GD
HP
G
lbf
0.965
1.142
1.220
1.181
1.181
1.181
1.181
1.654
1.654
1.654
1.732
1.732
1.732
2.008
2.008
2.008
2.008
2.008
2.205
2.205
2.205
2.205
2.480
2.874
3.071
3.071
3.268
3.268
3.268
3.976
3.976
4.173
4.173
4.173
4.173
4.488
5.512
5.512
5.512
SLD-23
ED
in
0.354
0.472
0.551
0.551
0.551
0.551
0.551
0.630
0.630
0.630
0.709
0.709
0.709
0.984
0.984
0.984
0.984
0.984
0.984
1.181
1.181
1.181
1.260
1.575
1.772
1.772
1.969
1.969
1.969
2.362
2.362
2.559
2.559
2.559
2.559
2.559
3.543
3.543
3.543
SLD
in
0.846
0.984
0.984
1.024
1.024
1.024
1.024
1.417
1.417
1.417
1.496
1.496
1.496
1.772
1.772
1.772
1.772
1.772
1.772
1.969
1.969
1.969
2.244
2.559
2.756
2.756
2.953
2.953
2.953
3.583
3.583
3.780
3.780
3.780
3.780
4.016
5.039
5.039
5.039
R
in
0.984
1.063
1.102
1.142
1.260
1.260
1.496
1.732
1.732
1.772
1.850
1.890
1.929
2.126
2.205
2.205
2.402
2.441
2.559
2.717
2.835
2.953
3.071
3.346
3.425
3.622
3.858
4.094
4.370
4.685
4.961
5.157
5.394
5.630
6.024
6.378
7.087
7.795
8.189
ED
pS
VSD
in
MA
ft-lb
447
pH
UJ
www.lovejoy-inc.com
-0 +0.0025
Mt
SP
+0 -0.0021
-0 +0.0021
Max
F
T
+0 -0.0018
-0 +0.0018
Max
D
+0 -0.0015
-0 +0.0015
T
GD
+0 -0.0013
-0 +0.0013
L
HP
+0 -0.0011
-0 +0.0011
l
G
+0 -0.0009
in
0.591
0.591
0.630
0.630
0.709
0.709
0.906
0.945
0.945
0.984
1.024
1.063
1.102
1.260
1.339
1.339
1.535
1.614
1.693
1.850
1.969
2.087
2.165
2.323
2.441
2.559
2.795
3.031
3.307
3.543
3.740
3.937
4.173
4.409
4.724
4.921
5.512
6.102
6.496
T2
in
B
MC
0.236
0.315
0.354
0.394
0.433
0.472
0.551
0.591
0.630
0.669
0.709
0.748
0.787
0.866
0.945
0.984
1.102
1.181
1.260
1.378
1.496
1.575
1.654
1.772
1.890
1.969
2.165
2.362
2.559
2.756
2.953
3.150
3.346
3.543
3.740
3.937
4.331
4.724
5.118
D1
SF
in
6x14
8x15
9x16
10x16
11x18
12x18
14x23
15x24
16x24
17x25
18x26
19x27
20x28
22x32
24x34
25x34
28x39
30x41
32x43
35x47
38x50
40x53
42x55
45x59
48x62
50x65
55x71
60x77
65x84
70x90
75x95
80x100
85x106
90x112
95x120
100x125
110x140
120x155
130x165
CJ
Size
D
T1
in
JIS
SLD 1900 Metric Series Dimensional Data
d
JW
L
B
l
T
MA
D
D1
d
F
Mt
pH
pS
T1
T2
Shaft Locking Devices
SLD 350 Series
JIS
CJ
CJ
SLD 350 Series Dimensional Data
SF
SF
= recommended distance to clamp device
= outer diameter of shaft locking device
= total width (relaxed state)
= preload force required to generate Mt
= shaft diameter
= maximum transmissible axial force
= maximum transmissible torque
= pressure on the hub
= pressure on the shaft
= tolerance of shaft
= tolerance of hub bore
JIS
N
D
L
FA
d
F
Mt
pH
pS
T1
T2
JW
JW
Dimensional Data
d
D
L
N
FA
SP
G
HP
GD
D
T
SP
T
UJ
UJ
D
VSD
VSD
GD
R
R
HP
SLD
SLD
Size
6x9
7X10
8X11
9X12
10x13
12x15
13x16
14x18
15x19
16x20
17x21
18x22
19x24
20x25
22x26
24x28
25x30
28x32
30x35
32x36
35x40
36x42
38x44
40x45
42x48
45x52
48x55
50x57
55x62
56x64
60x68
65x73
70x79
75x84
80x91
85x96
90x101
95x106
100x114
110x124
120x134
130x148
140x158
150x168
G
ED
ED
MC
MC
Distance (in)
in
0.236
0.276
0.315
0.354
0.394
0.472
0.512
0.551
0.591
0.630
0.669
0.709
0.748
0.787
0.866
0.945
0.984
1.102
1.181
1.260
1.378
1.417
1.496
1.575
1.654
1.772
1.890
1.969
2.165
2.205
2.362
2.559
2.756
2.953
3.150
3.346
3.543
3.740
3.937
4.331
4.724
5.118
5.512
5.906
T1
in
+0 -0.0003
+0 -0.0004
+0 -0.0005
+0 -0.0006
+0 -0.0015
+0 -0.0018
+0 -0.0021
+0 -0.0025
in
0.354
0.394
0.433
0.472
0.512
0.591
0.630
0.709
0.748
0.787
0.827
0.866
0.945
0.984
1.024
1.102
1.181
1.260
1.378
1.417
1.575
1.654
1.732
1.772
1.890
2.047
2.165
2.244
0.394
2.520
2.677
2.874
3.110
3.307
3.583
3.780
3.976
4.173
4.488
4.882
5.276
5.827
6.220
6.614
T2
in
-0 +0.0006
-0 +0.0007
-0 +0.0008
-0 +0.0010
-0 +0.0012
-0 +0.0014
-0 +0.0016
Max
Number of Elements
in
0.177
0.177
0.177
0.177
0.177
0.177
0.177
0.248
0.248
0.248
0.248
0.248
0.248
0.248
0.248
0.248
0.248
0.248
0.248
0.248
0.276
0.276
0.276
0.315
0.315
0.394
0.394
0.394
0.394
0.472
0.472
0.472
0.551
0.551
0.669
0.669
0.669
0.669
0.827
0.827
0.827
1.102
1.102
1.102
1
0.118
0.118
0.118
0.118
0.118
0.118
0.118
0.118
0.118
0.118
0.118
0.118
0.118
0.118
0.118
0.118
0.118
0.118
0.118
0.118
0.118
0.118
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.197
0.197
0.197
0.197
0.197
0.197
0.197
0.236
0.236
0.236
2
0.118
0.118
0.118
0.118
0.118
0.118
0.118
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.197
0.197
0.197
0.197
0.197
0.197
0.197
0.197
0.197
0.197
0.197
0.197
0.236
0.236
0.236
0.236
0.236
0.236
0.236
0.276
0.276
0.276
3
0.118
0.118
0.118
0.118
0.118
0.118
0.118
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.197
0.197
0.197
0.197
0.197
0.197
0.197
0.236
0.236
0.236
0.236
0.236
0.276
0.276
0.276
0.276
0.315
0.315
0.315
0.354
0.354
0.354
4
0.157
0.157
0.157
0.157
0.157
0.157
0.157
0.197
0.197
0.197
0.197
0.197
0.197
0.197
0.197
0.197
0.197
0.197
0.197
0.197
0.197
0.197
0.236
0.236
0.236
0.236
0.236
0.236
0.236
0.276
0.276
0.276
0.276
0.276
0.315
0.315
0.315
0.315
0.354
0.354
0.354
0.433
0.433
0.433
Max
Pressures
F
Mt
pH
pS
lbf
176
220
265
309
344
410
463
683
736
828
816
931
982
1,033
1,135
1,582
1,238
1,447
1,550
1,652
2,048
2,011
2,225
2,574
2,704
3,774
4,026
4,193
4,612
5,048
6,097
6,609
8,331
8,936
11,682
11,746
13,171
14,021
18,244
20,059
21,874
32,066
34,533
36,999
ft-lb
1.73
2.53
3.47
4.56
5.64
8.07
9.88
15.70
18.10
21.70
22.70
27.50
30.60
33.90
41.00
62.30
50.80
66.50
76.30
86.70
118.00
119.00
139.00
169.00
186.00
279.00
317.00
344.00
416.00
464.00
600.00
705.00
957.00
1,099.00
1,533.00
1,638.00
1,945.00
2,185.00
2,993.00
3,620.00
4,306.00
6,838.00
7,931.00
9,104.00
psi
10,878
12,473
13,053
13,053
14,504
13,053
13,053
13,053
13,053
13,053
13,053
13,053
13,053
13,053
13,053
14,504
14,504
14,504
14,504
14,504
14,504
14,504
14,504
14,504
14,504
14,504
14,504
14,504
14,504
14,504
14,504
14,504
14,504
14,504
14,504
14,504
14,504
14,504
13,053
13,053
13,053
13,053
13,053
13,053
psi
15,954
15,594
15,664
15,594
16,244
16,099
16,099
16,099
16,099
16,099
16,099
16,099
16,099
16,099
16,099
20,595
15,519
16,099
16,099
16,099
16,099
16,099
16,099
16,099
16,099
16,099
16,099
16,099
16,099
16,099
16,099
16,099
16,099
16,099
19,870
16,099
16,099
16,099
16,099
16,099
16,099
16,099
16,099
16,099
lb
899
1,124
1,349
1,574
1,754
2,091
2,360
3,485
3,754
4,002
4,159
4,496
4,743
4,991
5,485
7,644
5,980
6,992
7,486
7,981
9,892
10,251
10,746
12,432
13,061
18,232
19,446
20,255
22,279
25,741
29,450
31,923
40,241
43,163
56,427
59,889
63,621
71,489
88,125
96,893
105,660
154,893
166,808
178,723
Notes: n Do not use Molybdenum Disulfide lubricant.
n L ocking devices can be provided with a slit that allows the device to be expanded or contracted to accommodate many inch size shafts.
SLD-24
448
630-852-0500
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement