null  User manual
:: rangehoods.com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
INSTALLATION INSTRUCTIONS
MODELS RMIP33
AND
RMIP45
INTENDED FOR DOMESTIC COOKING ONLY
INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.
HOMEOWNER: USE AND CARE INFORMATION ON PAGES 11, 12 AND 13.
V05861 rev. D
READ AND SAVE THESE INSTRUCTIONS
Broan at ::rangehoods.com is a division of kitchen::
accessories
U
N
L
I
M
I
T
E
D
:: rangehoods.com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
! WARNING
! WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
TO REDUCE THE RISK OF INJURY TO PERSONS
IN THE EVENT OF A RANGE TOP GREASE
FIRE, OBSERVE THE FOLLOWING*:
1.
Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer at the address or telephone number
listed in the warranty.
1.
2.
Before servicing or cleaning unit, switch power off
at service panel and lock service disconnecting
means to prevent power from being switched on
accidentally. When the service disconnecting
means cannot be locked, securely fasten a prominent
warning device, such as a tag, to the service panel.
SMOTHER FLAMES with a close-fitting lid, cookie
sheet or metal tray, then turn off the burner. BE
CAREFUL TO PREVENT BURNS. IF THE
FLAMES DO NOT GO OUT IMMEDIATELY,
EVACUATE AND CALL THE FIRE DEPARTMENT.
2.
NEVER PICK UP A FLAMING PAN – You may
be burned.
3.
DO NOT USE WATER, including wet dishcloths or
towels – This could cause a violent steam explosion.
4.
Use an extinguisher ONLY if:
A. You own a Class ABC extinguisher and you
know how to operate it.
B. The fire is small and contained in the area
where it started.
C. The fire department has been called.
3.
Installation work and electrical wiring must be
done by qualified personnel in accordance with all
applicable codes and standards, including fire-rated
construction codes and standards.
4.
Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of
fuel burning equipment to prevent backdrafting.
Follow the heating equipment manufacturer’s
guidelines and safety standards such as those
published by the National Fire Protection
Association (NFPA), and the American Society for
Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code authorities.
5.
When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
6.
Ducted fans must always be vented to the outdoors.
7.
Do not use this unit with any solid-state speed control
device other than RMIPWC optional wall mounted
control.
8.
To reduce the risk of fire, use only metal ductwork.
9.
This unit must be grounded.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by
NFPA.
CAUTION
1.
2.
3.
4.
TO REDUCE THE RISK OF A RANGE TOP
GREASE FIRE:
a)
Never leave surface units unattended at high
settings. Boilovers cause smoking and greasy
spillovers that may ignite. Heat oils slowly on low or
medium settings.
b)
Always turn hood ON when cooking at high heat
or when cooking flaming foods.
c)
Clean ventilating fans frequently. Grease should
not be allowed to accumulate on fan or filter.
d)
Use proper pan size. Always use cookware
appropriate for the size of the surface element.
5.
6.
7.
8.
9.
10.
11.
-2-
For general ventilating use only. Do not use to
exhaust hazardous or explosive materials and vapors.
To avoid motor bearing damage and noisy and/or
unbalanced impellers, keep drywall spray,
construction dust, etc. off power unit.
Your insert motor has a thermal overload which will
automatically shut off the motor if it becomes
overheated. The motor will restart when it will cools
down. If the motor continues to shut off and restart,
have the insert serviced.
The minimum hood distance above cooktop must
not be less than 24’’. A maximum of 30’’ above
cooktop is highly recommended for best capture of
cooking impurities.
Two installers are recommended because of the
large size and weight of this insert.
To reduce the risk of fire and to properly exhaust
air, be sure to duct air outside – Do not exhaust
air into spaces within walls or ceiling or into
attics, crawl space or garage.
This product is equipped with a thermostat
which may start blower automatically. To reduce
the risk of injury and to prevent power from being
switched on accidentally, switch power off at
service panel and lock or tag service panel.
Because of the high exhausting capacity of this
insert, you should make sure enough air is entering
the house to replace exhausted air by opening a
window close to or in the kitchen.
To reduce the risk of fire and electrical shock, the
Rangemaster Models RMIP33 and RMIP45 must
be installed with blower models P5, P8, 331H,
332H, 335 or 336 only. Other blowers cannot be
substituted. (Blowers sold separately).
Use with approved cord-connection kit only.
Please read specification label on product for
further information and requirements.
Broan at ::rangehoods.com is a division of kitchen::
accessories
U
N
L
I
M
I
T
E
D
:: rangehoods.com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
RMIP33
AND RMIP45
INSERT SYSTEM
Model 634 or 644
(roof cap)
Model 647
(7” Rd wall cap)
Model 335 (1200 cfm)
or 336 (1500 cfm)
exterior blower
Model 643
(8” Rd wall cap)
Model 331H (600 cfm)
or 332H (900 cfm)
exterior blower
8” Rd
adjustable elbow
(optional)
Model 415
7” Rd adjustable
elbow (optional)
8” Rd
standard
duct
Model 407
(7” Rd x
24’’ section)
8” Rd metal
flexible duct
(optional)
7” Rd metal
flexible duct
(optional)
Model 412
transition
(3 1/4” x 10” to 7”)
Model 418
10” Rd
adjustable elbow
(optional)
Model 421
(10” Rd. vert.
in-line damper)
Model 410
(10” Rd duct - 2ft. sections)
Model 459 transition
(3 1/4” x 14” to 8”)
Adapter and damper
3 1/4’’ x 10’’
(supplied with P5
and P8 blowers)
Model 413
transition
(3 1/4” x
10” to 8”)
10” Rd metal
flexible duct
(optional)
Adapter and damper
3 1/4’’ x 14’’
(supplied with P8 blower)
Flow deviator
(supplied with P5 and P8 blowers)
RML3336, RML3342,
RML4548 or RML4560
Custom hood Liner (optional)
RMIPWC
Wall Control
(optional)
RBFIP Series
Baffle filters
(optional)
RMIP33 OR RMIP45
INSERT
Model 332 KR
exterior blower
rough-in kit.
Use with all exterior
blower models:
331H, 332H, 335, 336
Rough-in kit
(supplied with P5
and P8 blowers)
Model P5
single-blower
(500 cfm)
Model P8 dual-blower (900 cfm)
NOTE: The dual blower P8 can be
installed either with 8’’ or 7’’
round ductwork.
For optimal air and quiet sound
performance, use 8’’ round ductwork.
RMP Series Backsplash
(Stainless Steel wall
covering with warming
shelves. Optional)
-3Broan at ::rangehoods.com is a division of kitchen::
accessories
U
N
L
I
M
I
T
E
D
:: rangehoods.com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
1. SELECT BLOWER OPTION AND INSTALL DUCTWORK
Either an interior or exterior blower may be used with this insert. The insert model RMIP33 or RMIP45 must
be installed with blower models P5, P8, 331H, 332H, 335 or 336 only. Other blowers cannot be substituted.
(Blowers sold separately).
NOTE: The 331H, 332H, 335 or 336 exterior blower MUST BE installed with the rough-in kit model 332KR
(sold separately).
Plan where and how the ductwork will be installed. Access to the top of the hood is preferred for connection
of ductwork. As an alternative, flexible metal ductwork may be used.
Install proper-sized ductwork, elbows and roof or wall cap for the type of blower you are installing. Use round
ductwork, with a short section (about 4’ expanded) of flexible metal duct (optional) for attachment to the
transition. Use screws to attach flexible metal duct to the rigid duct. Use 2” duct tape to seal duct joints.
The minimum hood distance above cooktop must not be less than 24”. A maximum of 30” above
cooktop is highly recommended for best capture of cooking impurities.
Distances over 30” are at the installer and users discretion.
Roof cap
Exterior blower
7” or 8” round ducts
with 7” or 8” round
metal flex. duct (optional)
10” round duct
3 1/4” x 10” to 7” or 8” transition
or 3 1/4” x 14” to 8” transition
Wall
cap
10” round metal flex. duct
(optional)
Insert with
exterior blower
Insert with
interior blower
24” minimum
above cooking surface
24” minimum
above cooking surface
HH0039A
HH0038A
MODEL P5 (SINGLE) OR P8 (DOUBLE)
INTERIOR BLOWER TYPICAL DUCTWORK
MODEL 331H, 332H, 335 OR 336 EXTERIOR
BLOWER TYPICAL DUCTWORK
2. PREPARE THE INSTALLATION
Make sure that the following items are included:
- Insert
- Accessories:
• Filters (3 for RMIP33 model and 4 for RMIP45 model)
• Bag of parts including:
(4) lock nuts, (1) wire clamp, (8) #8 x 3/4” standard screws, (2) wire connectors,
(2) #6 x 1/2” standard screws, (8) #8 x 3/8” screws. Discard items not used.
Parts sold separately:
- Interior blower Model P5 includes blower, rough-in kit, flow deviator and 3 1/4” x 10” adapter
- Interior blower Model P8 includes blower, rough-in kit, flow deviator and 3 1/4” x 10” adapter
and 3 1/4” x 14” adapter
- Exterior blower Model 331H, 332H, 335 or 336
- Exterior blower rough-in kit Model 332KR (required for all exterior blower models)
- Halogen lights (120V, 50W, PAR 20) (2 for RMIP33 model and 3 for RMIP45 model)
- Custom hood liner Model RML3336, RML3342, RML4548 or RML4560 (optional)
- Backsplash RMP Series (optional)
- RMIPWC Remote control (optional)
- Baffle filters RBFIP Series (optional)
- Transitions, ducts (rigid and flexible), elbows, dampers, wall and roof caps. Refer to page 3 for a complete
list of venting options and model numbers.
NOTE: During installation, protect countertop and/or cooktop.
Broan at ::rangehoods.com is a division of kitchen::
accessories
U
N
L
I
M
I
T
E
D
:: rangehoods.com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
3. INSTALL BACKSPLASH (OPTIONAL)
It is recommended to install the backsplash before the custom hood insert. The custom hood will cover the
backsplash top mounting screws. In order to be able to install the backsplash, make sure you have at least
18’’ clearance between bottom of custom hood and range control panel or cooktop. (See instructions
packed with backsplash.)
4. CUSTOM HOOD PREPARATION
! WARNING
When building a custom hood, always follow all applicable construction codes and standards.
The custom hood frame must be sized to the shape and total weight of the insert assembly. Refer to the
table below for total weight of the insert, according to the type of blower choosen.
INSERT MODELS
RMIP33
RMIP45
WITH
P5
INT.BLOWER
41
49
LBS
LBS
WITH
P8
INT. BLOWER
49
57
WITH
LBS
LBS
Start with the custom hood base, because its position will
determine the height of the insert. We recommend the base
of the custom hood should be 3/4 inch thick plywood. If an
optional custom hood liner will be installed, we recommend
the sides and front of the custom hood to be 3/4 inch thick,
assuming standard cabinet widths. If the optional custom
hood liner will not be installed, the custom hood side and
front thickness is at the installer’s discretion.
Run power cable to installation location. Stub out a 4 foot
length of electrical cable below the custom hood.
If the RMIPWC optional remote control will be installed, run
electrical cable from the insert to the remote control location.
Stub out a 6 inch length from the remote control wall location.
Refer to the remote control installation instruction.
EXT. BLOWERS (ROUGH-IN PLATE ONLY)
27 LBS
35 LBS
Plywood base
thickness: 3/4”
Backsplash
(Optional)
24” to 30” above
cooking surface
Standard 36” h.
cooktop
HH0037A
5. SUGGESTED CUSTOM HOOD FRAME
The mounting holes for the 2 top stud supports are
located at 11 9/16” up from the insert base. The on
center distance between the 2 studs is 30 1/4” for the
RMIP33 insert model and 42 1/4” for the RMIP45 insert
model.
The mounting holes for the rear stud support are located
at 1 1/2” up from the insert base. See illustration beside. 1 1/2”
Once the custom hood base and frame are done, finalize
the custom hood.
Broan at ::rangehoods.com is a division of kitchen::
accessories
U
N
L
I
M
I
T
E
D
:: rangehoods.com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
6. INSTALL CUSTOM HOOD LINER (OPTIONAL)
The liners are specially designed to protect the exterior
base of the custom hood. All models are adjustable for
depth from 23 1/2’’ to 26 1/2’’ (front to back). The liner
must be installed before the insert. To order, refer to
table below to find the right liner part number for your
insert and for width of the custom hood. To install, see
instructions packed with the custom hood liner.
LINER MODEL
INSERT MODEL
CUSTOM HOOD
NOMINAL WIDTH
RML3336
RML3342
RML4548
RML4560
RMIP33
RMIP33
RMIP45
RMIP45
36’’
42’’
48’’
60’’
HA0022A
7. INSTALL THE RMIPWC REMOTE CONTROL (OPTIONAL)
The electrical connection for the remote control is located
in front of the insert. Perform this connection before the
insert installation. For installation details, see installation
instructions included with the RMIPWC remote control.
HL0044
8. CUT THE HOLE IN CUSTOM HOOD BASE
If it is not done yet, cut a hole in the bottom of the cabinet,
using the dimensions shown beside.
INSERT MODEL NUMBER
RMIP33
RMIP45
3 1/2''
A
32 1/2’’
44 1/2’’
NOTES: 1. The notch shown in the inset must be cut only if
the RMIPWC optional remote control will be
installed.
2.The recommended distance from the back to
the rearmost cutout edge is 2 1/4’’ minimum.
17 1/16''
2 1/4''
min.
16 3/8''
A
HD0084
9. INSTALL BLOWER (EXTERIOR OR INTERIOR)
INTERIOR BLOWER: Follow all subsequent steps of this manual.
EXTERIOR BLOWER: Refer to instructions packed with exterior blower and follow steps 13, 14, 16, 17,
19 and up of this manual.
-6-
Broan at ::rangehoods.com is a division of kitchen::
accessories
U
N
L
I
M
I
T
E
D
:: rangehoods.com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
10. REMOVE THE KNOCK-OUT OPENING (INTERIOR BLOWER)
Remove the knockout on rough-in plate. See picture below.
CAUTION
When using P5 blower, remove the 10’’ wide knockout (smaller part). If using P8 blower, remove
the knockout corresponding to the ducting installed (10’’ or 14’’ adapter/damper).
UT
CKO
NO
14’’ K
OUT
OCK
KN
10’’
HD0077
Removing vertical knockout opening on rough-in plate
11. INSTALL THE DEVIATOR (INTERIOR BLOWER)
Install the deviator as shown.
NOTE: To prevent the deviator from sliding out of the rough-in
plate, put some tape on the deviator base after sliding it
into the rough-in plate (provided with the P5 and P8 blower)
opening. If installed correctly, the deviator will protrude
about 1/8” above the rough-in plate.
12. INSTALL THE ADAPTER (INTERIOR BLOWER)
Using two (2) #6 x 1/2’’ screws provided with insert, secure the adapter to the top of the rough-in plate.
Remove tape from damper flap. Seal the adapter to the rough-in plate by using duct tape.
Broan at ::rangehoods.com is a division of kitchen::
accessories
U
N
L
I
M
I
T
E
D
:: rangehoods.com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
13. CONNECT WIRING (INTERIOR & EXTERIOR BLOWER)
! WARNING
Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with
all applicable codes and standards. Before connecting wires, switch power off at service panel
and lock service disconnecting means to prevent power from being switched on accidentally.
Position insert below the installed custom hood. Pull cable through hole in top of insert.
INTERIOR BLOWER: Remove the cable knock-out on the top of the rough-in plate. Remove rough-in plate
wiring cover. Place the wire clamp in the knock-out hole, insert the cable through the wire clamp in the
rough-in plate wiring box. Tighten the wire clamp to secure the cable.
Connect cable into wiring box using provided wire connectors.
Connect wires as follow: BLACK to BLACK, WHITE to WHITE
and GREEN or BARE wire under ground screw. DO NOT FORGET
TO CONNECT THE GROUND. Reinstall wiring cover.
EXTERIOR BLOWER: Remove rough-in plate wiring cover and connect wiring (see instructions included
with exterior blower).
14. INSTALL THE ROUGH-IN PLATE (INTERIOR & EXTERIOR BLOWER)
INTERIOR BLOWER: Carefully install the rough-in
plate inside the top of the
insert with four (4) lock nuts.
See picture beside.
EXTERIOR BLOWER: Refer to instructions included with 332 KR rough-in plate (sold separately). Secure
the rough-in plate inside the top of the insert with (4) lock nuts.
15. INSTALL THE TRANSITION (INTERIOR BLOWER)
Slide the transition over the adapter/damper. Seal the transition to the
adapter/damper by using duct tape.
Broan at ::rangehoods.com is a division of kitchen::
accessories
U
N
L
I
M
I
T
E
D
:: rangehoods.com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
16. DUCTING CONNECTION (INTERIOR & EXTERIOR BLOWER)
A. When there is access to the top of the hood, connect ductwork
and seal connections with duct tape after Step 17 Install the
insert.
B. When there is no access to the top of the hood, carefully pull
down the metal duct through the custom hood base hole. Slide
this duct over the transition (interior blower) or over the flange
of the rough-in plate (exterior blower). Make sure the
adapter/damper assembly enters the ducting. Seal the connection
with duct tape.
CAUTION
Take care not to kink ducting when installing insert (step 17).
17. INSTALL THE INSERT
If an optional wall control will be installed, refer to its installation instructions now. When done, continue the
insert installation.
Install the insert inside the
custom hood and secure to the
frame by using the #8 x 3/4”
mounting screws provided.
Start with 4 screws on top
and finish with 2 on rear
side. (See figure beside for
mounting screw specific
locations.)
REAR
TOP
HD0085
CAUTION
Take care not to kink ducting or pinch electrical cable when installing insert.
18. INSTALL THE BLOWER (INTERIOR BLOWER)
The blower must be installed to the rough-in plate using (6) #8 x 3/8” screws for the single blower unit and
(8) #8 x 3/8” screws for the dual blower unit. Remove the cover from the blower assembly. Remove the
impeller(s) by pulling them out gently (see pictures below).
Broan at ::rangehoods.com is a division of kitchen::
accessories
U
N
L
I
M
I
T
E
D
:: rangehoods.com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
18. INSTALL THE BLOWER (INTERIOR BLOWER) (CONT’D)
Install (4) #8 x 3/8’’ screws into the location as shown in the pictures below (single blower or dual blower). Do
not tighten screws down fully, leave a 1/8” gap. Hang blower unit onto blower plate (screws through the large
part of the keyhole). Slide the blower to its position (screws in the small part of the keyhole). Tighten the
(4) screws.
Dual blower (P8)
Single blower (P5)
HD0081
Dual blower (P8)
Single blower (P5)
FOR DUAL BLOWER UNIT, MAKE
SURE THE IMPELLERS ARE
CORRECTLY INSTALLED, THE
INSERT
WILL
NOT WORK
PROPERLY IF REVERSED. Both
impellers are different in the dual
blower, one rotates clockwise and
the other counterclockwise. Each
wheel and motor have an arrow and
a number on them, you have to
match them correctly (see drawing
beside).
FRONT
2
1
HD0023
! WARNING
Never plug the 2-prong blower cord to the 3-prong power supply cord.
Plug the power supply to the 3-prong male connector (A) and the
blower unit into the 2-prong female receptacle (B) inside the
insert.
A
B
HE0022
Broan at ::rangehoods.com is a division of kitchen::
accessories
U
N
L
I
M
I
T
E
D
:: rangehoods.com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
19. LIGHT BULBS
This insert uses 50W halogen lamps (120V, 50W, PAR 20) (Purchase separately).
Install the lamps by rotating them clockwise into their socket holder.
20. INSTALL FILTERS
It is recommended to install side filters first and finish with center one(s).
1. Insert upper end of filter into the insert (finger sized cup side).
2. Raise lower end of filter to position it into grease rail inside of hood and pull.
3. While pulling the filter, slide it under the inner retaining piece.
Replacement filters are available from your dealer. See inside label insert for size and part number.
1
2
3
HD0086
1) Finger sized cup
Baffle Filters
Baffle filters are available as an option. To order them, refer to the table below to
find the right filter kit number for your insert. To install them, refer to instruction
sheet included with baffle filter kit.
KIT #
INSERT MODEL
RBFIP33
RBFIP45
RMIP33
RMIP45
BAFFLE FILTER (TYPICAL)
21. USE AND CARE
Grease filters and impeller(s).
The grease filters, impeller(s) and grease rail should be cleaned frequently. Use a warm detergent
solution. Grease filters and impeller(s) are dishwasher safe.
Remove grease filters by pushing them towards the back of hood and rotating downward.
Stainless steel cleaning: How to maintain its « BRIGHT LOOK »
Do:
- Regularly wash surfaces with clean cloth or rag soaked with warm water and mild soap or liquid dish detergent.
- Always clean in the direction of original polish lines.
- Always rinse well with clear water (2 or 3 times) after cleaning. Wipe dry completely.
- You may also use a specialized household stainless steel cleaner.
- 11 Broan at ::rangehoods.com is a division of kitchen::
accessories
U
N
L
I
M
I
T
E
D
:: rangehoods.com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
21. USE AND CARE (CONT’D)
Don’t:
- Do not use any steel or stainless steel wool or any other scrapers to remove stubborn dirt.
- Do not use any harsh or abrasive cleansers.
- Do not allow dirt to accumulate.
- Do not let plaster dust or any other construction residues reach the hood. During construction or
renovation, cover the hood to make sure no dust sticks to stainless steel surface.
Avoid: when choosing a detergent
- Any cleaners that contain bleach will attack stainless steel.
- Any products containing : chloride, fluoride, iodide, bromide will deteriorate surfaces rapidly.
- Any combustible products used for cleaning such as acetone, alcohol, ether, benzol, etc., are
highly explosive and should never be used close to a range.
22. OPERATION
Always turn your blower on before you begin cooking to establish an air flow in the kitchen. Let the blower run for
a few minutes to clear the air after you turn off the range.This will help keep the whole kitchen cleaner and brighter.
2
1
3
1) ON/OFF blower switch
2) Blower speed control
3) Halogen light switches
BLOWER
The blower is operated using two (2) controls or with the RMIPWC optional wall control.
Use the red, lighted on/off switch to start and stop the blower. When turned on, the blower will operate at
the previous setting of the speed control.
Turn the speed control knob clockwise to decrease blower speed – counterclockwise to increase speed.
COOKTOP LIGHTING (HALOGEN)
A double set of ON/OFF switches controls the halogen lights.
The front rocker controls the center light (for 45” inserts). The rear rocker controls both side lights (each
switch controls one light for 33” insert). Select one, two or three lights for best cooking lighting.
Use PAR 20, 50W halogen bulbs. (Purchase separately)
HEAT SENTRY™
This isert is equipped with a Heat Sentry™ thermostat. This thermostat is a device that will turn on or speed
up the blower if it senses excessive heat above the cooking surface.
1) If blower is OFF - it turns blower ON to HIGH speed.
2) If blower is ON at a lower speed setting – it turns the blower up to HIGH speed.
! WARNING
The HEAT SENTRY™ can start the blower even if the insert is turned OFF. In this case, it is impossible
to turn the blower OFF with blower switch. If you must stop the blower, do it from the main
electrical panel.
When the temperature level drops to normal, the blower will return to its original setting.
Test all insert switches. If a RMIPWC remote control is installed, test all its switches.
Finalize the custom hood.
Broan at ::rangehoods.com is a division of kitchen::
accessories
U
N
L
I
M
I
T
E
D
:: rangehoods.com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
22. OPERATION (CONT’D)
RMIPWC REMOTE CONTROL (OPTIONAL)
An optional remote control is also available to operate your hood
insert. For installation details, see installation instructions included
with the RMIPWC remote control.
NOTE: When the RMIPWC remote control is connected to the
insert, the control switches on the insert are no longer
operational.
HC0006
1 2
3
1) Light switch
2) Blower ON/OFF switch
23. WIRING DIAGRAM
3) Blower speed control
! WARNING
Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with
all applicable codes and standards. Before connecting wires, switch power off at service panel
and lock service disconnecting means to prevent power from being switched on accidentally.
NEMA 5-15P
PLUG
Wall control remote by-pass Plug
BK
BK
120V, 60Hz
in
1
1
2
2 O
3
3
4
4 BL
5
5
6
6 W
7
7
8
8
O
BK
W
Y
FAN SWITCH
G
BL
BK
SPEED CONTROL
O
BN
1
BK
BK
3
2
R
W
LIGHTS
SWITCH
W
BK
R
P
BK
FAN MOTOR
OUTLET
HS
THERMOSTAT
Y
BK
4
BK
Y
5
BN
R
W
nc
1
2
BK
9
9
Pin #9 is empty
LIGHT SOCKET LEFT
BL
W
BK
LIGHT SOCKET CENTER
W
BK
R
Grounding
plate
TERMINAL BLOCK
W
W
nc
nc
LIGHT SOCKET RIGHT
NOTE 1
W
W
W
W
NOTES
1. Light socket not included in
RMIP33 model.
2. If any of the original wire, as
supplied, must be replaced, use the
same equivalent wire.
3. Field wiring must comply with
applicable codes, ordinances and
regulations.
WIRING COLOR CODE
BK
BL
BN
G
O
BLACK
BLUE
BROWN
GREEN
ORANGE
BK
P
P
R
W
Y
PURPLE
RED
WHITE
YELLOW
Broan at ::rangehoods.com is a division of kitchen::
accessories
U
N
L
I
M
I
T
E
D
:: rangehoods.com
Call 1-800-667-8721 anywhere in the US and Canada - www.rangehoods.com
WARRANTY
BROAN-NUTONE LLC ONE-YEAR LIMITED WARRANTY
Broan-NuTone LLC warrants to the original consumer purchaser of its products that such products will be free from defects in
materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OR MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE.
During this one-year period, Broan-NuTone LLC will, at its option, repair or replace, without charge, any product or part which
is found to be defective under normal use and service.
This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse,
negligence, accident, improper maintenance or repair (other than by Broan-NuTone LLC), faulty installation or installation
contrary to recommended installation instructions.
The duration of any implied warranty is limited to the one-year period as specified for the express warranty. Some states or
provinces do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.
BROAN-NUTONE LLC’S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE LLC’S OPTION, SHALL BE THE
PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE LLC SHALL NOT BE
LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH
PRODUCT USE OR PERFORMANCE. Some states or provinces do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to
another. This warranty supersedes all prior warranties.
To qualify for warranty service, you must (a) notify the company stated below, (b) give the model number and part identification and
(c) describe the nature of any defect in the product or part. At the time of requesting warranty service, you must present
evidence of the original purchase date.
SERVICE PARTS
RMIP33 and RMIP45 MODELS
1
7
8
2
5
4
3
KEY
#
PART
NUMBER
1
2
V03493
V03686
V15085
V15086
V03435
V03501
V02512
V02773
V02772
V03505
V00673
V02264
V03502
V03503
V03504
V05865
V05866
V02544
V05861
3
4
5
6
7
8
9
10
11
12
13
14
15
V03888
DESCRIPTION
RANGEMASTER LOGO
FILTER CLIP
GREASE RAIL 33’’
GREASE RAIL 45’’
THERMOSTAT
SPEED CONTROL
SCREW #8-32 x 1/2’’, QUADREX
MALE CONNECTOR
FEMALE CONNECTOR
TERMINAL STRIP
LOCK NUT #8-32
SOCKET LAMP
SPST DOUBLE SWITCH (HAL. LIGHT)
SPSTLIGHTED SINGLE SWITCH (BLOWER)
SPEED CONTROL BUTTON
MICROMESH FILTERS 9.250’’ X 12.500’’
MICROMESH FILTERS 11.130’’ X 12.500’’
HALOGEN LAMP PAR 20 50W
INSTALLATION MANUAL
PARTS BAG ((4) lock nut #10--32, (1)
wire clamp LP16-AP, (2) wire connectors
#74B, (8) #8 x 3/4” screws, (8) #8 x 3/8”
screws, (2) #6 x 1/2" screws)
6
MODEL
33 45
1
3
1
1
1
2
1
1
1
2
2
1
1
1
3
3
1
1
4
1
1
1
2
1
1
1
2
3
1
1
1
2
2
4
1
1
1
9
10
14
13
12
15
HL0043
Broan at ::rangehoods.com is a division of kitchen::
accessories
U
N
L
I
M
I
T
E
D
11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement