Mytee | 1001DX | User manual | Mytee 1001DX User manual

Mytee 1001DX User manual
Instructions for
1000DX,1000DX-200, 1001DX,
1001DX-200, 1003DX, 1005DX Speedster
Please read before use.
Register your product
at www.mytee.com/help
Model #
1000DX & 1000DX-200 p.3
1001DX & 1001DX-200 p.9
1003DX p.15
1005DX p.21
General information p.27
Serial #
Form # ADM-Speedster
12-10
13655 Stowe Dr., Poway, Ca. 92064
1
®
2
1000DX & 1000DX-200 SPEEDSTER
1000DX & 1000DX-200 SPEEDSTER® FRONT
10
1
1000DX & 1000DX-200 SPEEDSTER® BACK
11
2
12
3
4
13
5
9
14
6
8
1. Switch plate
2. 2” Male Cuff-Lynx™
3. Solution lid
4. Female quick disconnect (QD)
5. Front handle
7
16
6. Front vent
7. Bottom handle
8. 5” locking casters
9. Solution tank
10.Recovery lid
11. Recovery tank
12. Push handle
13. Drain valve
14. Power cord
1000DX & 1000DX-200 SPEEDSTER® ITEMS INCLUDED
H110 Cuff-Lynx™
2” Hose Adapter
H141 Cuff-Lynx™
2” Hose Reducer to 1.5”
H375 - Hose Hanger
(4) screws
H226 Drain Elbow
15
15. Back vent
16. 12” Rear wheels
1000DX & 1000DX-200 SPEEDSTER® CORD
Plug the power cord into a single, 20A grounded wall outlet.
3
1000DX & 1000DX-200 SPEEDSTER
1000DX & 1000DX-200 SPEEDSTER® VAC/SOL
HOSE CONNECTIONS
1000DX & 1000DX-200 SPEEDSTER® SWITCHES
Vac 1 Vac 2
Pump
Attach one end of a solution hose to a wand or other tool, the other
end to the Speedster’s® front quick disconnect. Attach one end of
a vacuum hose to the tool, the other end to the Speedster’s® CuffLynx™ vacuum hose port.
Turn on Vac 1, Vac 2 and Pump switches.
1000DX & 1000DX-200 SPEEDSTER® BALL FLOAT
1000DX & 1000DX-200 SPEEDSTER® FILL
SOLUTION TANK
Lift lid and manually fill the tank.
An internal ball float automatically turns off the machine’s vacuum
when the water in the solution tank reaches its maximum level.
Empty the recovery tank as needed using the rear drain valve.
4
1000DX & 1000DX-200 SPEEDSTER
1000DX & 1000DX-200 SPEEDSTER® DUMP VALVE
1000DX & 1000DX-200 SPEEDSTER®
FILTER MAINTENANCE
INTAKE
FILTER
Attach the 45˚ drain elbow to the drain spout in back. Lift up the
dump valve and empty the tank.
Check and clean solution tank filter daily by twisting off, rinsing with
clean water and replacing.
1000DX & 1000DX-200 SPEEDSTER®
LOCKING CASTERS
MYTEE® SYSTEM MAINTAINER
Locking casters help keep the machine remain stationary during
use.
Weekly flushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical build-up,
improving pump life, performance and pressure.
5
Order parts at: www.mytee.com/products/product.php?id=1000DX
6
C
D
E
F
Part prices are subject to change.
A
B
H485
H210
H342
H666
H216
P731
H254
H251
H219
H371
H221
G131
E550
H220
H201
H601
H768
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
B186
B103
B107
H212
36
37
38
39
B106
53
8
B102
7
nipple, brass, 1/4" x close
qd, brass, 1/4" f
adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex
B111
52
sol tank, speedster
51
P732
49
nut, hex, 1/4-20 s/s
washer, nylon, 9/16id x 1-1/16od x .031
H215
48
washer, 1/4" lock, s/s
washer, buna 1-1/8" od x 3/16" id
bolt, 1/4-20 x 1-1/4" hex head
bracket, rear, fb/spy
pump, 120psi, demand, 115V
screw, #10-32 x 1-1/4" phil pan head, zinc
bushing, brass, 3/8"mpt x 1/4"
elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt
washer, 9/16"id x 1"od, flat, s/s
nipple, brass, 1/4"m, hex
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
washer, 11/16"id x 1-1/2"od x .075, s/s
adapter, brass, 1/2" barb x 3/8" fsw, ball end
clamp, hose, 5/16-29/32
sol hose, 1/2" kuri 100psi
nut, kep, #10-32 zinc
elbow, brass, 90 deg, 1/2" barb x 3/8"mpt
clamp, hose, 2-1/4 dia
cuff hose, 2 X 2, wire reinforced
vac hose, 2", wire reinforced
exhaust boot, plastisol
vac motor, 2 stage high performance
vac support, 2 stage, 3-1/8"
gasket, vacuum motor
manifold, dual vac, parallel
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
plate, manifold, parallel
bolt, 1/4-20 x 1/2", hex head, zinc
fitting, strain relief, cord
power cord, pigtail, 30", 12/3, black
connector, cord lock
nut, lock, 1/2" steel
axle, 18.25" x .50" dia
cap, axle, 1/2"
wheel, 12"
washer, axle, cut 1/2" id
base, speedster
bolt, 1/4-20 x 1" hex head, s/s
washer, 1/4" flat, s/s
handle, breeze and dx
washer, 1/4"id x 1"od, flat, s/s
H413
H213
47
guard, cooling fan, wire
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
50
H203
G052
44
46
H912
43
45
H222
C305
42
B105
H299
35
41
B160
34
B136
H347
33
40
PH615-26
29
32
H217
28
B172
H544
27
H273
PH628-24
26
31
G059
25
30
H500
C310
24
G004
H211
4
23
H770
3
P750
nut, lock, 1/4-20 nylon insert
H296
2
22
caster, 5"
H343
screw, #10 x 5/8" hex head, zinc
PART NO.
DESCRIPTION
7
1
8
ITEM
NO.
1
1
1
2
1
2
4
6
2
1
1
4
1
1
4
1
2
1
5
1
4
1
4
1
3
1
1
2
2
6
2
1
11
1
8
1
1
1
1
1
2
2
4
1
13
2
8
19
2
8
10
2
8
QTY.
6
$0.99 ea
$1.99 ea
$0.99 ea
$9.99 ea
$151.99 ea
$0.99 ea
$3.19 ea
$4.99 ea
$0.99 ea
$3.19 ea
$4.49 ea
$8.99 ea
$0.99 ea
$3.49 ea
$1.99 ea
$8.99/ft
$0.99 ea
$9.49 ea
$1.49 ea
$12.49 ea
$8.99/ft
$4.99 ea
$103.99 ea
$3.99 ea
$8.99 ea
$15.99 ea
$0.99 ea
$13.49 ea
$0.99 ea
$3.19 ea
$11.49 ea
$4.99 ea
$1.99 ea
$9.99 ea
$0.99 ea
$41.99 ea
$0.99 ea
$141.99 ea
$0.99 ea
$23.19 ea
$0.99 ea
$0.99 ea
$6.99 ea
$0.99 ea
$0.99 ea
$2.99 ea
$0.99 ea
6
H378
58
P682
65
69
P685
H612
H389
H338
E515
H135
G083
P733
H304
C322D
PART NO.
DESCRIPTION
4
4
hanger, wire formed, hose
H375
5
gasket, strip, 3/4" x 36" x 1/8"
Cuff-Lynx, female swivel x female thread 2"
Cuff-Lynx, 2" to 1.5" reducer
H140
H141
E530
G010
G085
DESCRIPTION
power cord, ext, 50', 12/3, black
filter, bag, vac tank, drawstring
PART NO.
pump, 220psi, demand, 120V
DESCRIPTION
inlet, 2"
washer, #8 flat, s/s
screw, #10-32 x 1/2" SHCS, alloy
plate, switch, sp, 3 hole
switch, rocker, 2 position
Cuff-Lynx, 2" m cuff x 2" mpt
gasket, 2" inlet
vac tank, speedster
screw, #8 x 5/8 phil oval, s/s
lid, vac tank, black, 7"
gasket, 7", vac lid
elbow, inlet assembly 2"
elbow, 2" float
float, 2", ball style
pipe, pvc, 2"
adaptor, pvc 2, fmsl x fmt
gasket, cam fitting polyethylene, 2.35" OD 1.90" ID
spout, drain, 45 degree
valve, drain, 1-1/2"
bracket, "L" (all extracters)
bolt, 1/4-20 x 1-1/2" hex head, s/s
bracket, front hinge, sp/fb
nipple, brass, 3/8" x close
bushing, brass, 1/2"mpt x 3/8" fpt, hex
filter, strainer, 1/2"
hose, 3/8" x 17-1/2", (OAL), f x -fsw, surge, 1600psi
Items Not Shown
44
ITEM
NO.
1000DX-200
79
78
77
76
75
74
73
72
71
G090
G091
68
70
P726
A926
67
H490
P684
64
66
G002
H226
H225
H390A
63
62
61
60
H316
B216
57
59
B210
56
B119A
AH105
55
PART NO.
54
5
ITEM
NO.
1
QTY
1
1
1
2
1
1
QTY
1
2
2
1
3
1
1
1
6
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
QTY.
MSRP
$0.99 ea
$36.99 ea
$11.99 ea
$15.99 ea
$11.49 ea
$18.49 ea
$7.99/ft
$6.99 ea
$6.49 ea
$3.19 ea
$20.99 ea
$6.99 ea
$0.99 ea
$8.99 ea
$1.99 ea
$2.49 ea
$6.49 ea
$31.99 ea
3
$10.99 ea
$3.99 ea
$3.99 ea
$4.99 ea
$74.99
$9.99 ea
MSRP
$208.99 ea
MSRP
$10.99 ea
$0.99 ea
$0.99 ea
$6.99 ea
$13.99 ea
$3.99 ea
$2.49 ea
$190.99 ea
3
NAME
J. Cash
DATE
10/12/10
2
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
2
SCALE: 1:8
1
DO NOT
SCALE DRAWING
REV
SHEET 1 OF 2
1000DX
SIZE DWG. NO.
C
PRODUCTS, INC.
858-679-1191
speedster
mytee
TITLE:
1
A
B
C
D
E
F
1000DX & 1000DX-200 SPEEDSTER
8
8
6
9
21
22
23
24
21
25
20
26
29
13
16
19
27
12
17
28
7
14
15
7
18
11
33
34
10
36
37
38
to sol tank filter
thru B216 (#58)
7
39
9
8
32
35
40
41
to female QD
thru AH105-18 (#55)
6
7
42
43
5
31
6
4
3
30
6
6
2
1
5
5
45
4
44
46
48
47
4
to pump "IN"
thru B186 (#36)
3
3
46
57
35
56
59
55
9
4
58
49
4
19
47
6
46
5
52
to female QD
thru B111 (#52)
53
4
51
to pump "OUT"
thru B106 (#54)
to pump "OUT"
thru B107 (#39)
37
39
21
54
50
3
3
66
62
63
64
65
61
67
2
2
60
3
69
68
79
70
78
77
J. Cash
NAME
76
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
1
SCALE: 1:7
DO NOT SCALE
DRAWING
1000DX
SHEET 2
speedster
SIZE DWG. NO.
D
858-679-1191
mytee PRODUCTS, INC
74
TITLE:
73
10/12/10
DATE
75
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
72
71
1
1000DX & 1000DX-200 SPEEDSTER
Cord Input Primary
L2
GND
White
Green
Black
Inline Conn.
White
Black
Black
Black
SW-DPST
E515
Inline Conn.
Switch
Pressure
C322D
Inline Conn.
White
Pressure Pump
L2
Green
GND
L1
Black
1000DX
Inline Conn.
Green
Black
SW-DPST
E515
Inline Conn.
SW-DPST
E515
Inline Conn.
Vacuum Motor 2
C310
Inline Conn.
Vacuum Motor 1
C310
Inline Conn. Inline Conn.
Mytee Products
13655 Stowe Dr.
Poway, CA
Size: Letter
Number: 0000
Revision: A
92064
Time: 1:49:31 PM Sheet 1 of 1
Date: 11/30/2010
--File: C:\Compaines\GHI\Projects\Mytee Schematics\1000DX\1000DX.SCHDOC
Title
Green
White
Black
L2
Yellow
Black
Green
Black
L1
GND
White
Black
L2
Black
Brown
8
Blue
Green
GND
L1
L1
1000DX & 1000DX-200 SPEEDSTER
Black
1001DX & 1001DX-200 SPEEDSTER
1001DX & 1001DX-200 SPEEDSTER® FRONT
10
1
1001DX & 1001DX-200 SPEEDSTER® BACK
12
11
2
3
4
13
5
9
14
6
8
1. Switch plate
2. 2” Male Cuff-Lynx™
3. Solution lid
4. Female quick disconnect (QD)
5. Front handle
7
16
6. Front cooling fan
7. Bottom handle
8. 5” locking casters
9. Solution tank
10.Recovery lid
11. Recovery tank
12. Push handle
13. Drain valve
14. Dual power cords
1001DX & 1001DX-200 SPEEDSTER® ITEMS INCLUDED
15
15. Back vent
16. 12” Rear wheels
1001DX & 1001DX-200 SPEEDSTER® CORDS
Left cord: Powers Vac 2 & Heater 2.
Right cord: Powers Vac 1, Heater 1 & Pump.
Yellow tag
indicates primary
cord.
H110 Cuff-Lynx™
2” Hose Adapter
H141 Cuff-Lynx™
2” Hose Reducer to 1.5”
H375- Hose Hanger
(4) screws
H226 Drain Elbow
Plug each power cord into a separate, 20A grounded wall outlet.
Outlets must be on two separate breakers. When the amber
light on the switch plate illuminates, the machine is on separate
circuits (not necessarily 20A circuits). You can identify the primary
cord by the yellow tag.
9
1001DX & 1001DX-200 SPEEDSTER
1001DX & 1001DX-200 SPEEDSTER® VAC/SOL
HOSE CONNECTIONS
1001DX & 1001DX-200 SPEEDSTER® SWITCHES
Vac 1 Vac 2
Heater 1
Pump Heater 2
Attach one end of a solution hose to a wand or other tool, the other
end to the Speedster’s® front quick disconnect. Attach one end of
a vacuum hose to the tool, the other end to the Speedster’s® CuffLynx™ vacuum hose port.
“On” switches are located on the plate in front of the machine. To
use vacuums, turn on Vac 1 and Vac 2 switches. To use pump,
turn on Pump switch. To activate heat, turn on Heater switch.
Heater 1 for 1000 watts of heat. Heater 2 for 2000 watts of heat.
1001DX & 1001DX-200 SPEEDSTER®
FILL SOLUTION TANK
1001DX & 1001DX-200 SPEEDSTER®
FILTER MAINTENANCE
INTAKE
FILTER
Lift lid and manually fill the tank.
Check and clean solution tank filter daily by twisting off, rinsing
with clean water and replacing.
10
1001DX & 1001DX-200 SPEEDSTER
1001DX & 1001DX-200 SPEEDSTER® BALL FLOAT
1001DX & 1001DX-200 SPEEDSTER® DUMP VALVE
An internal ball float automatically turns off the machine’s
vacuum when the water in the solution tank reaches its maximum level. Empty the recovery tank as needed using the rear
dump valve.
Attach the 45˚ drain elbow to the drain spout in back. Lift up the
dump valve and empty the tank.
1001DX & 1001DX-200 SPEEDSTER®
LOCKING CASTERS
MYTEE® SYSTEM MAINTAINER
Locking casters help keep the machine remain stationary during
use.
Weekly flushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical build-up,
improving pump life, performance and pressure.
11
Order parts at: www.mytee.com/products/product.php?id=1001DX
12
C
D
E
F
Part prices are subject to change.
A
B
H347
B160
B186
H299
47
48
49
50
8
C305
PH615-26
46
53
B172
45
B105
H201
44
B136
H217
43
52
H544
42
51
PH628-24
H500
38
41
G004
37
C310
P750
36
G059
H768
35
40
H601
34
39
E573
H212
33
E574
31
32
B108
H903A
30
B142
28
29
E519
27
18
H274
H220
17
26
E550
16
H528
G131
15
H222
H371
14
25
H219
13
24
H251
12
H273
H254
11
23
P731
10
B103
H216
9
22
H666
8
AH156
H342
7
21
H210
6
H221
H485
5
AH105
H211
4
20
H770
3
19
H296
C317
2
H343
1
8
PART NO.
ITEM
NO.
7
7
pump, 120psi, demand, 115V
bushing, brass, 3/8"mpt x 1/4"
elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt
washer, 11/16"id x 1-1/2"od x .075, s/s
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
adapter, brass, 1/2" barb x 3/8" fsw, ball end
clamp, hose, 5/16-29/32
sol hose, 1/2" kuri 100psi
elbow, brass, 90 deg, 1/2" barb x 3/8"mpt
bolt, 1/4-20 x 1/2", hex head, zinc
clamp, hose, 2-1/4 dia
cuff hose, 2 X 2, wire reinforced
vac hose, 2", wire reinforced
exhaust boot, plastisol
vac motor, 2 stage high performance
vac support, 2 stage, 3-1/8"
gasket, vacuum motor
manifold, dual vac, parallel
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
plate, manifold, parallel
washer, 9/16"id x 1"od, flat, s/s
Thermostat, 200°, Auto, 1/4"
Thermostat, 310°F ± 10°F, Manual, 1/4"
heater, aluminum cast, single
valve, brass, 1/4" check
coupling, brass, 1/4" fpt x 1/4" fpt
heating rod, 1000W, 115V
screw, 6 x 3/16, phil pan head, self tapping
bracket, heater mounting, dual
screw, #10-32 x 1-1/4" phil pan head, zinc
nut, kep, #10-32 zinc
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
hose, 3/8" x 6", (OAL), f x fsw, surge, 1600psi
hose, 3/8" x 17-1/2", (OAL), f
nut, lock, 1/2" steel
fitting, strain relief, cord
power cord, pigtail, 30", 12/3, black
connector, cord lock
axle, 18.25" x .50" dia
cap, axle, 1/2"
wheel, 12"
washer, axle, cut 1/2" id
base, speedster
nut, lock, 1/4-20, nylon insert, s/s
caster, 5"
bolt, 1/4-20 x 1" hex head, s/s
washer, 1/4" flat, s/s
handle, breeze and dx
washer, 1/4"id x 1"od, flat, s/s
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
fan, cooling, 115V
guard, cooling fan, wire
screw, #10 x 5/8" hex head, zinc
DESCRIPTION
1
1
1
5
1
1
4
1
1
8
3
1
1
2
2
6
2
1
11
1
4
2
2
2
1
1
2
10
1
6
6
4
2
2
2
2
2
2
1
2
2
4
1
13
2
8
19
2
8
10
1
3
12
QTY.
MSRP
6
$151.99 ea
$3.19 ea
$4.99 ea
$0.99 ea
$8.99 ea
$3.49 ea
$1.99 ea
$8.99/ft
$9.49 ea
$0.99 ea
$1.49 ea
$12.49 ea
$8.99/ft
$4.99 ea
$103.99 ea
$3.99 ea
$8.99 ea
$15.99 ea
$0.99 ea
$13.49 ea
$0.99 ea
$16.49 ea
$17.99 ea
$78.99 ea
$13.99 ea
$4.49 ea
$51.99 ea
$0.99 ea
$29.99 ea
$0.99 ea
$0.99 ea
$4.49 ea
$23.99 ea
31.99 ea
$1.99 ea
$3.19 ea
$11.49 ea
$4.99 ea
$9.99 ea
$0.99 ea
$41.99 ea
$0.99 ea
$141.99 ea
$0.99 ea
$23.19 ea
$0.99 ea
$0.99 ea
$6.99 ea
$0.99 ea
$0.99 ea
$21.49 ea
$2.99 ea
$0.99 ea
6
A926
P685
91
C322D
58
4
hanger, wire formed, hose
H375
5
power cord, ext, 50', 12/3, black
filter, bag, vac tank, drawstring
gasket, strip, 3/4" x 36" x 1/8"
Cuff-Lynx, female swivel x female thread 2"
Cuff-Lynx, 2" to 1.5" reducer
DESCRIPTION
pump, 220psi, demand, 120V
DESCRIPTION
inlet, 2"
washer, #8 flat, s/s
screw, #10-32 x 1/2" SHCS, alloy
plate, switch, sp, 4 hole
light, indicator, 125v (amber)
switch, rocker, 2 position
switch, rocker, 3 position
light, red, 250v
Cuff-Lynx, 2" m cuff x 2" mpt
gasket, 2" inlet
vac tank, speedster
screw, #8 x 5/8 phil oval, s/s
lid, vac tank, black, 7"
gasket, 7", vac lid
elbow, inlet assembly 2"
elbow, 2" float
float, 2", ball style
pipe, pvc, 2"
adaptor, pvc 2, fmsl x fmt
1
2
1
2
1
1
QTY
gasket, cam fitting polyethylene, 2.35" OD 1.90" ID
valve, drain, 1-1/2"
bracket, "L" (all extracters)
bracket, front hinge, sp/fb
bolt, 1/4-20 x 1-1/2" hex head, s/s
nipple, brass, 3/8" x close
bushing, brass, 1/2"mpt x 3/8" fpt, hex
filter, strainer, 1/2"
nipple, brass, 1/4" x close
nipple, brass, 1/4"m, hex
qd, brass, 1/4" f
E530
G010
G085
H140
H141
PART NO.
washer, nylon, 9/16id x 1-1/16od x .031
sol tank, speedster
nut, hex, 1/4-20 s/s
washer, 1/4" lock, s/s
washer, buna 1-1/8" od x 3/16" id
bolt, 1/4-20 x 1-1/4" hex head
bracket, rear, fb/spy
DESCRIPTION
4
adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex
Items Not Shown
PART NO.
ITEM
NO.
1001DX-200
H612
H389
H348
E512B
E515
E516
E511
H135
G083
90
89
88
87
86
85
84
83
82
P733
H304
80
81
G090
79
G091
77
78
P726
H490
P682
P684
76
75
74
73
G002
H225
71
72
H390A
H378
H316
B216
B210
B119A
B106
B107
B102
B111
H413
P732
70
69
68
67
66
65
64
63
62
61
60
59
H215
H213
57
58
H203
G052
56
H912
PART NO.
5
55
54
ITEM
NO.
1
QTY
1
3
3
1
1
3
1
2
1
1
1
6
1
1
1
1
1
1
1
1
1
2
1
2
1
1
1
1
1
1
1
2
1
2
4
6
2
1
MSRP
MSRP
$208.99 ea
MSRP
$10.99 ea
$0.99 ea
$0.99 ea
$6.99 ea
$9.99 ea
$13.99 ea
$14.99 ea
$5.99 ea
$3.99 ea
$2.49 ea
$190.99 ea
$0.99 ea
$36.99 ea
$11.99 ea
$15.99 ea
$11.49 ea
$18.49 ea
$7.99/ft
$6.99 ea
$6.49 ea
$20.99 ea
$6.99 ea
$8.99 ea
$0.99 ea
$1.99 ea
$2.49 ea
$6.49 ea
$3.49 ea
$3.19 ea
$17.99 ea
$3.49 ea
$0.99 ea
$141.99
$0.99 ea
$0.99 ea
$1.99 ea
$0.99 ea
$9.99 ea
3
$10.99 ea
$74.99 ea
$9.99 ea
$4.99 ea
$3.99 ea
$3.99 ea
QTY.
3
NAME
J. CAsh
DATE
9/24/2010
2
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
2
SCALE: 1:8
1
DO NOT
SCALE DRAWING
1001DX
SIZE DWG. NO.
C
SHEET 1 OF 2
REV
PRODUCTS, INC.
858-679-1191
speedster
mytee
TITLE:
1
A
B
C
D
E
F
1001DX & 1001DX-200 SPEEDSTER
8
8
13
26
32
31
24
25
27
30
23
28
29
7
10
35
36
37
38
35
21
21
39
22
7
34
40
7
20
13
17
to pump "OUT"
thru B136 (#51)
14
to female QD
thru B103 (#22)
16
44
43
41
42
18
12
19
15
to sol tank filter
thru B216 (#67)
to heater
thru AH156 (#21)
11
6
47
48
49
6
46
51
2
9
10
50
52
8
7
24
6
23
7
4
53
5
3
45
5
5
1
55
56
5
58
57
to pump "IN"
thru B186 (#49)
4
4
56
54
5
4
67
50
4
66
68
65
10
22
69
59
44
7
22
56
35
33
6
62
3
to female QD
thru B111 (#61)
64
5
61
to heater
thru AH105-18 (#20)
to heater
thru AH105-18 (#20)
33
63
20
57
60
3
75
72
73
74
71
76
2
77
2
70
4
78
J. Cash
NAME
89
81
82
80
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
858-679-1191
1
SCALE: 1:6
DO NOT SCALE
DRAWING
1001DX
REV
SHEET 2 OF 2
speedster
SIZE DWG. NO.
D
85
83
mytee PRODUCTS, INC.
86
84
TITLE:
87
9/24/2010
DATE
88
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
91
90
79
1
1001DX & 1001DX-200 SPEEDSTER
A
B
C
D
E
F
Inline Conn.
L1 Black
GND
L2 Inline Conn.
White
Cord Input Secondary
Entry Location, Bottom
or Far Left
Green
White / Red
C322D
Heater Switch
Black
3-Position
E516
Red
Black
E511
Lamp Heater 2
E511
Lamp Heater 1
Orange
SW-DPST
E515
Inline Conn.
Pressure
Switch
Black
Red
Pressure Pump
Inline Conn.
Green
White / Red
Inline Conn.
L2 Black White
Orange / Black
Red
Vacuum Motor 1
Inline Conn.
White
Black
Green
L2
GND
Green
Vacuum Motor 2
SW-DPST
E515
Black
Inline Conn.
C310
GND Green
Inline Conn.
Yellow Black L1
White
Orange
1001DX
Thermal
Switch
C519
Green
Green
Red
Black
Thermal
Switch
C519
Mytee Products
13655 Stowe Dr.
Poway, CA
Size: Letter
Number: 0000
Revision: A
92064
Time: 10:45:09 AM Sheet 1 of 1
Date: 11/30/2010
--File: C:\Compaines\GHI\Projects\Mytee Schematics\1001DX\1001DX.SCHDOC
Title
Red
SW-DPST
E515
Inline Conn.
White / Red
White
C310
Inline Conn.
L2 Black White
GND Green
Inline Conn.
Brown Black L1
Cord Input Primary
Entry Location, Top or Far Right
White / Red
Red
Black
White Red
L2
Heater 1
L1
Red
Cooling Fan
C317
White / Red
White
White / Red
Green
GND
White / Red
L2
L1
White
Red
L1b
L2b
Pink 18 AWG
Light 2
Pink 18 AWG Light 1 L2a
L1
GND
L2
GND
Heater 2
White
Thermal Switch
Green
Orange / Black
White
Green
Black
Thermal Switch
Green
Orange
L1
Black
14
Blue
L1a
E564
Circuit Detector
E512B
Lamp Amber
Black
1001DX & 1001DX-200 SPEEDSTER
1003DX SPEEDSTER
1003DX SPEEDSTER® FRONT
1
1003DX SPEEDSTER® BACK
10
11
2
12
3
4
5
13
9
14
6
7
1. Switch plate
2. 2” Male Cuff-Lynx™
3. Solution lid
4. Female quick disconnect (QD)
5. Front handle
17
15
8
16
6. Front cooling fan
7. Prime Valve
8. Pressure Regulator
9. Solution tank
10.Recovery lid
11. Push handle
12. Recovery tank
13. Drain valve
14. Back vent
15. Dual Power cords
1003DX SPEEDSTER® ITEMS INCLUDED
16. 12” Rear wheels
17. 5” locking casters
1003DX SPEEDSTER® CORD
Left cord: Powers Vac 2 & Heater 2.
Right cord: Powers Vac 1, Heater 1 & Pump.
H110 Cuff-Lynx™
2” Hose Adapter
H141 Cuff-Lynx™
2” Hose Reducer to 1.5”
H375- Hose Hanger
(4) screws
H226 Drain Elbow
Yellow tag
indicates primary
cord.
Plug each power cord into a separate, 20A grounded wall outlet.
Outlets must be on two separate breakers. When the amber
light on the switch plate illuminates, the machine is on separate
circuits (not necessarily 20A circuits). You can identify the primary
cord by the yellow tag.
15
1003DX SPEEDSTER
1003DX SPEEDSTER® VAC/SOL
HOSE CONNECTIONS
1003DX SPEEDSTER® SWITCHES
Vac 1
Vac 2
Pump
Heater
1
2
“On” switches are located on the plate in front of the machine. To
use vacuums, turn on Vac 1 and Vac 2 switches. To use pump,
turn on Pump switch. To activate heat, use lower right switch.
Press to the left for 1,000 watts, press to the right for 2,000 watts.
1003DX SPEEDSTER® FILL SOLUTION TANK
1003DX SPEEDSTER® PRIME VALVE
& PRESSURE REGULATOR
Sp
Attach one end of a solution hose to a wand or other tool, the other
end to the Speedster’s® front quick disconnect. Attach one end of
a vacuum hose to the tool, the other end to the Speedster’s®
Cuff-Lynx™ vacuum hose port.
16
l
Prime the pump by turning the valve to the Prime position (as
shown above) for 30 seconds, then turn right to the Run position.
Turn the Pressure Regulator to the left to decrease water pressure. Turn the Pressure Regulator to the right to increase water
pressure.
Lift lid and manually fill the tank.
be
LOWER PSI
La
RUN POSITION
e
PRESSURE
REGULATOR
im
Pr
HIGHER PSI
r
te
ds
ee
PRIME POSITION
1003DX SPEEDSTER
1003DX SPEEDSTER® FILTER MAINTENANCE
1003DX SPEEDSTER® BALL FLOAT
INTAKE
FILTER
An internal ball float automatically turns off the machine’s vacuum
when the water in the solution tank reaches its maximum level.
Empty the recovery tank as needed using the rear dump valve.
Check and clean solution tank filter daily by twisting off, rinsing
with clean water and replacing.
MYTEE® SYSTEM MAINTAINER
1003DX SPEEDSTER® DUMP VALVE
& LOCKING CASTERS
Above, empty the recovery tank by attaching the 45˚ drain elbow to
the drain spout in back. Lift up the dump valve and empty the tank.
Below, locking casters help keep the machine remain stationary
during use.
Weekly flushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical build-up,
improving pump life, performance and pressure.
17
Order parts at: www.mytee.com/products/product.php?id=1003DX
18
B
C
D
E
F
PH628-20
H544
AH184
B246
C313
B242
B172
B160
PH615-36
B210
46
47
48
49
50
51
52
53
54
55
bushing, brass, 1/2"mpt x 3/8" fpt, hex
sol hose, 1/2" kuri 100psi
adapter, brass, 1/2" barb x 3/8" fsw, ball end
elbow, brass, 90 deg, 1/2" barb x 3/8"mpt
tee, brass, 3/8" fpt x 3/8" mpt x 3/8" fpt
pump, 450 psi, 115V
plug, brass, 3/8" mpt, hex
hose, 3/8" x 14-1/2" (OAL), f surge
cuff hose, 2 X 2, wire reinforced
vac hose, 2", wire reinforced
clamp, hose, 2-1/4 dia
vac support, 3 stage, 4-1/16"
H217
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
gasket, vacuum motor
H501
G004
41
exhaust boot, plastisol
45
G059
40
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
44
H768
39
plate, manifold, parallel
manifold, dual vac, parallel
vac motor, 3 stage, 120V, tangential
P750
38
H770
H601
37
bolt, 1/4-20 x 1/2", hex head, zinc
C302
H201
36
sol hose, 1/4" x 24 1/2", (OAL), f x fsw, 3000psi
hose, 3/8" x 6.5", (OAL), f x fsw, surge, 1600psi
Thermostat, 200°, Auto, 1/4"
screw, 6 x 3/16, phil pan head, self tapping
Thermostat, 310°F ± 10°F, Manual, 1/4"
heating rod, 1000W, 115V
nut, kep, #10-32 zinc
screw, #10-32 x 3/4" phil pan head, zinc
bracket, heater mounting, dual
heater, aluminum cast, single
connector, cord lock
power cord, pigtail, 30", 12/3, black
fitting, strain relief, cord
nut, lock, 1/2" steel
axle, 1/2" x 18-1/2", sp, breeze
cap, axle, 1/2"
wheel, 12"
washer, axle, cut 1/2" id
base, speedster
bolt, 1/4-20 x 1" hex head, s/s
caster, 5"
washer, 1/4" flat, s/s
nut, lock, 1/4-20 nylon insert
fan, cooling, 115V
screw, #10 x 5/8" hex head zinc
guard, cooling fan, wire
sol hose, kuriyama, 3/8"
clamp, hose, 5/16-29/32
adapter, brass, 3/8" barb x 1/4" fsw
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
ball valve, 1/4''
washer, 9/16"id x 1"od, flat, s/s
nipple, brass, 1/4"m, hex
elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt
hose, 3/8" x 10", (OAL), f x f
DESCRIPTION
43
AH108S
35
8
42
E573
AH156
H274
32
34
E574
31
33
E519
H220
23
H273
H221
22
30
H371
21
29
H219
20
H256
H251
19
28
H254
18
H528
P731
17
27
H342
16
H903A
H666
15
26
H210
14
E550
H216
13
G131
C317
12
25
H343
11
24
H296
10
B103
6
PH715-25
B656
5
9
H212
4
B235
B107
3
H347
B136
2
8
AH103
1
7
PART NO.
ITEM
NO.
7
2
1
2
3
1
1
4
1
1
1
3
6
2
8
2
2
10
1
1
8
3
1
2
10
2
2
4
2
1
2
2
2
2
2
1
2
2
4
1
12
2
20
16
1
12
3
1
16
2
11
1
14
3
2
1
QTY.
$2.49 ea
$8.99/ft
$3.49 ea
$9.49 ea
$13.99 ea
$588.99 ea
$1.99 ea
$27.99 ea
$12.49 ea
$8.99/ft
$1.49 ea
$4.99 ea
$140.99
$0.99 ea
$8.99 ea
$4.99 ea
$0.99 ea
$15.99 ea
$13.49 ea
$0.99 ea
$26.49 ea
$23.99 ea
$16.49 ea
$0.99 ea
$17.99 ea
$51.99 ea
$0.99 ea
$0.99 ea
$29.99 ea
$78.99 ea
$4.99 ea
$11.49 ea
$3.19 ea
$1.99 ea
$9.99 ea
$0.99 ea
$41.99 ea
$0.99 ea
$141.99 ea
$0.99 ea
$23.19 ea
$0.99 ea
$0.99 ea
$21.49 ea
$0.99 ea
$2.99 ea
$7.99/ft
$1.99 ea
$7.99 ea
$4.49 ea
$13.49 ea
$0.99 ea
$3.19 ea
$4.99 ea
$30.49 ea
MSRP
B111
60
B652
P726
E516
102
108
107
106
105
104
P685
B130
H308D
H289
H246
H389
E515
101
103
E511
H337
E512B
H135
G083
G091
H304
G090
100
99
98
97
96
95
94
93
A926
P733
91
92
P682
H118
90
89
88
H490
P684
86
87
G002
H226
H225
B119A
85
84
83
82
H299
H378
80
81
H316
79
H485
B106
77
78
AH105
76
B102
H413
74
75
H215
G052
H211
73
72
71
H203
P732
69
70
H390A
H912
H213
B135
B105
PH615-12
68
67
66
65
64
63
62
C313C
B644
59
61
PH615-24
58
B186
B216
56
57
PART NO.
ITEM
NO.
spout, drain, 45 degree
valve, drain, 1-1/2"
filter, strainer, 1/2"
washer, 11/16"id x 1-1/2"od x .075, s/s
bracket, front hinge, sp/fb
bolt, 1/4-20 x 1-1/2" hex head, s/s
handle, breeze and dx
nipple, brass, 1/4" x close
hose, 3/8" x 17-1/2", (OAL), f
qd, brass, 1/4" f
washer, nylon, 9/16id x 1-1/16od x .031
nut, hex, 1/4-20 s/s
washer, buna 1-1/8" od x 3/16" id
washer, 1/4"id x 1"od, flat, s/s
bolt, 1/4-20 x 1-1/4" hex head
sol tank, speedster
bracket, "L" (all extracters)
bracket, rear, fb/spy
washer, 1/4" lock, s/s
tee, brass, 1/4" mpt
bushing, brass, 3/8"mpt x 1/4"
sol hose, 1/2" kuri 100psi
elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt
regulator, 450 psi
adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex
adapter, brass, 1/2" barb x 1/4" mpt
sol hose, 1/2" kuri 100psi
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
nipple, brass, 3/8" x close
DESCRIPTION
inlet, 2"
45 deg, street elbow, brass, 1/4" male NPTF
gauge, pressure, 2000 PSI
washer, #10 flat, s/s
screw, 8-32 x 3/8" SHCS, alloy, Black
screw, #10-32 x 1/2" SHCS, alloy
switch, rocker, 3 position
switch, rocker, 2 position
light, red, 250v
plate, switch, sp, 4 hole w/gauge
light, indicator, 125v (amber)
Cuff-Lynx, 2" m cuff x 2" mpt
gasket, 2" inlet
gasket, 7", vac lid
screw, #8 x 5/8 phil oval, s/s
lid, vac tank, black, 7"
elbow, inlet assembly 2"
vac tank, speedster
pipe, pvc, 2"
screw, 10 x 3/4, self-tap, hex head, zinc
elbow, 2" float
float, 2", ball style
adaptor, pvc 2, fmsl x fmt
gasket, cam fitting polyethylene, 2.35" OD 1.90" ID
6
5
1
1
1
3
2
1
1
3
2
1
1
1
1
1
6
1
1
1
1
3
1
1
1
1
1
1
1
5
1
2
1
2
1
1
4
2
6
6
2
1
2
1
4
1
1
1
1
1
3
1
1
2
2
QTY.
$10.99 ea
$5.49 ea
$38.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$14.99 ea
$13.99 ea
$5.99 ea
$8.99 ea
$9.99 ea
$3.99 ea
$2.49 ea
$11.99 ea
$0.99 ea
$36.99 ea
$15.99 ea
$190.99 ea
$7.99/ft
$0.99 ea
$11.49 ea
$18.49 ea
$6.99 ea
$6.49 ea
$3.19 ea
$20.99 ea
$6.49 ea
$0.99 ea
$8.99 ea
$0.99 ea
$6.99 ea
$3.49 ea
$31.99 ea
$17.99 ea
$0.99 ea
$0.99 ea
$1.99 ea
$0.99 ea
$0.99 ea
$141.99 ea
$6.99 ea
$9.99 ea
$0.99 ea
$5.49 ea
$3.19 ea
$8.99/ft
$8.49 ea
$86.99 ea
$3.49 ea
$2.49 ea
$8.99/ft
$8.99 ea
$1.99 ea
MSRP
E530
E564
G010
G085
H140
H141
H375
PART NO.
DESCRIPTION
power cord, ext, 50', 12/3, black
controller, circuit light
filter, bag, vac tank
gasket, strip, 3/4" x 36" x 1/8"
Cuff-Lynx, female swivel x female thread 2"
Cuff-Lynx, 2" to 1.5" reducer
hanger, wire formed, hose
Items Not Shown
4
3
2
1
1
2
1
1
1
QTY
MSRP
$74.99 ea
$62.49 ea
$9.99 ea
$4.99 ea
$3.99 ea
$3.99 ea
$10.99 ea
1003DX SPEEDSTER
Part prices are subject to change.
19
8
8
25
40
41
42
43
24
39
44
20
38
37
19
23
45
46
22
21
6
36
7
34
13
47
32
33
18
7
17
31
30
15
16
35
29
6
28
65
to heater "IN"
6
27
14
13
26
to female QD
thru B103 (#6)
48
to pressure gauge
thru B136 (#2)
6
36
6
12
6
11
64
49
7
10
14
16
50
63
9
7
52
51
8
53
to vac tank
thru B111 (#62)
52
13
to sol tank filter
thru B186 (#59)
39
1
49
8
42
52
54
4
5
6
2
67
56
57
5
4
53
3
68
5
4
59
69
to sol tank
39
62
57
to pump "IN"
thru B160 (#55)
to unloader
thru B111 (#62)
55
58
81
60
56
70
66
71
81
14
61
36
72
55
to prime valve
thru B136 (#2)
4
80
72
4
82
13
71
78
14
72
71
79
39
73
66
3
77
4
74
to heater "OUT"
thru AH108S (#36)
6
4
76
6
3
60
74
4
87
3
75
85
86
88
84
83
90
89
2
to prime valve
thru B235 (#7)
91
92
2
108
60
4
77
4
107
93
NAME
J. Cash
2
10/12/10
DATE
36
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
104
99
103
100
1
DO NOT SCALE
DRAWING
1003DX
SCALE: 1:6
D
REV
OD
SHEET 2 OF 2
speedster
858-679-1191
SIZE DWG. NO.
TITLE:
mytee PRODUCTS, INC.
102
101
to pump "OUT"
thru AH108S (#36)
105
98
106
97
96
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
6
29
95
94
1
A
B
C
D
E
F
1003DX SPEEDSTER
20
1003DX
E511
Lamp Heater 2
E511
Lamp Heater 1
Orange
Orange / Black
Black
Mytee Products
13655 Stowe Dr.
Poway, CA
Revision: A
Size: Legal
Number: 0000
92064
Date: 12/7/2010
Time: 10:34:12 AM Sheet 1 of 1
--File: C:\Compaines\GHI\Projects\Mytee Schematics\1003DX\1003DX.SCHDOC
Title
Heater Switch
Black
3-Position
Red
E516
Red
Black
SW-DPST
E515
Pressure Pump
C313
Inline Conn.
Red
Vacuum Motor 1
Cord Input Secondary
Entry Location,
Bottom or Far Left
White / Red
C302
Inline Conn.
SW-DPST
E515
Black
Inline Conn.
Vacuum Motor 2
Inline Conn.
L1 Black
GND
Inline Conn.
L2 White
White / Red
Red
SW-DPST
E515
Inline Conn.
C302
White / Red
White / Red
Orange
Thermal Switch
1000W
GND
White
Red
Black
Thermal Switch
1000W
GND
Heater 2
White
Red
Cooling Fan
E317
White / Red
White
White / Red
E564
E512B
Lamp Amber
Red
L1b
L2b
Pink 18 AWG Light 2
Pink 18 AWG Light 1 L2a
L1a
Circuit Detector
Cord Input Primary
Entry Location, Top or Far Right
White
Black
L1
GND
L2
White / Red
Red
Black
White Red
White / Red
Heater 1
L2
GND White / Red
L1
Blue
L1
Black
L2 Black White
GND
Inline Conn.
Black L1
Yellow
White/Red
L2 Black
GND
Inline Conn.
Brown
Thermal Switch
L2
L1
Orange / Black
Thermal Switch
L2
L1
Orange
White
Black
1003DX SPEEDSTER
1005DX SPEEDSTER
1005DX SPEEDSTER® FRONT
1
1005DX SPEEDSTER® BACK
10
11
2
12
3
4
5
13
9
14
6
7
1. Switch plate
2. 2” Male Cuff-Lynx™
3. Solution lid
4. Female quick disconnect (QD)
5. Front handle
17
15
8
16
6. Front vent
7. Prime Valve
8. Pressure Regulator
9. Solution tank
10.Recovery lid
11. Push handle
12. Recovery tank
13. Drain valve
14. Back vent
15. Dual Power cords
1005DX SPEEDSTER® ITEMS INCLUDED
16. 12” Rear wheels
17. 5” locking casters
1005DX SPEEDSTER® CORD
Left cord: Powers power Vac 2.
Right cord: Powers Vac 1 & Pump.
H110 Cuff-Lynx™
2” Hose Adapter
H141 Cuff-Lynx™
2” Hose Reducer to 1.5”
H375 - Hose Hanger
(4) screws
H226 Drain Elbow
Yellow tag
indicates primary
cord.
Plug each power cord into a separate, 20A grounded wall outlet.
Outlets must be on two separate breakers. When the amber
light on the switch plate illuminates, the machine is on separate
circuits (not necessarily 20A circuits). You can identify the primary
cord by the yellow tag.
21
1005DX SPEEDSTER
1005DX SPEEDSTER® VAC/SOL
HOSE CONNECTIONS
1005DX SPEEDSTER® SWITCHES
Vac 1
Vac 2
Pump
“On” switches are located on the plate in front of the machine. To
use vacuums, turn on Vac 1 and Vac 2 switches. To use pump,
turn on Pump switch. Bottom right switch has no use.
Attach one end of a solution hose to a wand or other tool, the other
end to the Speedster’s® front quick disconnect. Attach one end of
a vacuum hose to the tool, the other end to the Speedster’s® CuffLynx™ vacuum hose port.
Sp
LOWER PSI
Prime the pump by turning the valve to the Prime position (as
shown above) for 30 seconds, then turn right to the Run position.
Turn the Pressure Regulator to the left to decrease water pressure. Turn the Pressure Regulator to the right to increase water
pressure.
Lift lid and manually fill the tank.
22
l
RUN POSITION
be
PRESSURE
REGULATOR
La
HIGHER PSI
e
PRIME POSITION
im
Pr
1005DX SPEEDSTER® PRIME VALVE
1003DX
& PRESSURE REGULATOR
r
te
ds
ee
1005DX SPEEDSTER® FILL SOLUTION TANK
1005DX SPEEDSTER
1005DX SPEEDSTER® FILTER MAINTENANCE
1005DX SPEEDSTER® BALL FLOAT
INTAKE
FILTER
An internal ball float automatically turns off the machine’s vacuum
when the water in the solution tank reaches its maximum level.
Empty the recovery tank as needed using the rear dump valve.
Check and clean solution tank filter daily by twisting off, rinsing
with clean water and replacing.
MYTEE® SYSTEM MAINTAINER
1005DX SPEEDSTER® DUMP VALVE
& LOCKING CASTERS
Above, empty the recovery tank by attaching the 45˚ drain elbow to
the drain spout in back. Lift up the dump valve and empty the tank.
Below, locking casters help keep the machine remain stationary
during use.
Weekly flushing of the solution system with Mytee® System
Maintainer helps keep lines clean and prevents chemical build-up,
improving pump life, performance and pressure.
23
Order parts at: www.mytee.com/products/product.php?id=1005DX
24
A
B
C
D
E
F
H212
B103
8
9
Part prices are subject to change.
H225
54
8
H226
H390A
49
A926
H770
48
53
H347
47
52
PH715-28
46
H135
B235
45
G083
B106
44
51
B130
43
50
B119
42
H203
41
35
H215
H308D
34
40
H389
33
H273
H612
32
H337
H246
31
39
AH105
30
38
B111
29
E515
B102
28
E512B
B186
27
36
B216
26
37
B210
H299
25
B119A
24
H219
22
G052
H251
21
23
H254
H371
P731
18
19
H768
17
20
H485
H211
15
16
H666
H202
13
14
H316
B107
7
12
H201
6
B656
H213
5
H216
H210
4
11
H378
3
10
guard, cooling fan, wire
H343
7
valve, drain, 1-1/2"
spout, drain, 45 degree
elbow, inlet assembly 2"
gasket, 2" inlet
Cuff-Lynx, 2" m cuff x 2" mpt
bracket, "L" (all extracters)
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
clamp, hose, 5/16-29/32
sol hose, kuriyama, 3/8"
adapter, brass, 3/8" barb x 1/4" fsw
nipple, brass, 1/4" x close
45 deg, street elbow, brass, 1/4" male NPTF
filter, strainer, 1/4"
bolt, 1/4-20 x 1-1/4" hex head
nut, hex, 1/4-20 s/s
nut, kep, #10-32 zinc
plate, switch, sp, 4 hole w/gauge
light, indicator, 125v (amber)
switch, rocker, 2 position
gauge, pressure, 2000 PSI
screw, #10-32 x 1/2" SHCS, alloy
washer, #8 flat, s/s
screw, 8-32 x 3/8" SHCS, alloy, Black
hose, 3/8" x 24 1/2", (OAL)
adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex
qd, brass, 1/4" f
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
nipple, brass, 3/8" x close
washer, 11/16"id x 1-1/2"od x .075, s/s
bushing, brass, 1/2"mpt x 3/8" fpt, hex
filter, strainer, 1/2"
washer, buna 1-1/8" od x 3/16" id
cap, axle, 1/2"
wheel, 12"
axle, 18.25" x .50" dia
washer, axle, cut 1/2" id
base, speedster
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
washer, 1/4"id x 1"od, flat, s/s
handle, breeze and dx
bolt, 1/4-20 x 3/4" hex head, s/s
caster, 5"
bolt, 1/4-20 x 1-1/2" hex head, s/s
nut, lock, 1/4-20 nylon insert
ball valve, 1/4''
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
washer, 9/16"id x 1"od, flat, s/s
nipple, brass, 1/4"m, hex
bolt, 1/4-20 x 1/2", hex head, zinc
washer, 1/4" lock, s/s
washer, 1/4" flat, s/s
bracket, front hinge, sp/fb
screw, #10 x 5/8" hex head zinc
H296
2
7
DESCRIPTION
8
PART NO.
ITEM
NO.
1
1
1
1
1
1
2
8
16
1
2
1
1
1
2
2
2
1
1
4
1
1
3
2
1
3
1
2
2
10
2
1
6
2
2
1
4
1
13
8
2
18
2
2
17
1
7
10
4
2
2
23
1
10
2
QTY.
MSRP
6
$20.99 ea
$3.19 ea
$15.99 ea
$2.49 ea
$3.99 ea
$6.99 ea
$0.99 ea
$1.99 ea
$7.99/ft
$7.99 ea
$3.49 ea
$5.49 ea
$3.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$8.99 ea
$9.99 ea
$13.99 ea
$38.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$31.99 ea
$3.49 ea
$17.99 ea
$8.99 ea
$1.99 ea
$0.99 ea
$2.49 ea
$6.49 ea
$1.99 ea
$0.99 ea
$41.99 ea
$9.99 ea
$0.99 ea
$141.99 ea
$0.99 ea
$0.99 ea
$6.99 ea
$0.99 ea
$23.19 ea
$0.99 ea
$0.99 ea
$13.49 ea
$4.49 ea
$0.99 ea
$3.19 ea
$0.99 ea
$0.99 ea
$0.99 ea
$8.99 ea
$0.99 ea
$2.99 ea
6
5
H217
75
4
cuff-lynx, female swivel x female thread 2"
cuff-lynx, 2" to 1.5" reducer
H140
H141
4
hanger, wire forned, hose
gasket, strip, 3/4" x 36" x 1/8"
G085
H375
filter, bag, vac tank, draw string
controller, circuit light
power corf, ext 50', 12/3 black
DESCRIPTION
sol hose, 1/4" x 24 1/4"
tee, brass, 1/4" mpt
bushing, brass, 3/8"mpt x 1/4"
pump, 450 psi, 115V
sol hose, 1/2" kuri 100 psi
tee, brass, 3/8" fpt x 3/8" mpt x 3/8" fpt
elbow, brass, 90 deg, 1/2" barb x 3/8"mpt
plug, brass, 3/8" mpt, hex
sol hose, 1/2" kuri 100 psi
hose, 3/8" x 10", (OAL), f x f
elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt
elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt
regulator, 450 psi
adapter, brass, 1/2" barb x 1/4" mpt
sol hose, 1/2" kuri 100 psi
1
1
1
2
1
1
2
QTY.
adapter, brass, 1/2" barb x 3/8" fsw, ball end
exhaust boot, plastisol
cuff hose, 2 X 2, wire reinforced
vac hose, 2" wire reinforced, gray
clamp, hose, 2-1/4 dia
motor, 3-stage, 115 cfm,14.5 amps
gasket, vacuum motor
manifold, dual vac, parallel
vac support, 3 stage, 4-1/16"
plate, manifold, parallel
bracket, rear, fb/spy
nut, lock, 1/2" steel
fitting, strain relief, cord
power cord, pigtail, 30", 12/3, black
connector, cord lock
sol tank, speedster
float, 2", ball style
screw, #8 x 5/8 phil oval, s/s
lid, vac tank, black, 7"
gasket, 7", vac lid
elbow, 2" float
pipe, pvc, 2"
adaptor, pvc 2, fmsl x fmt
inlet, 2"
vac tank, speedster
DESCRIPTION
G010
E564
E530
PART NO.
5
AH108S
B135
B105
C313
PH615-36
B242
Items not shown
94
93
92
91
90
89
B172
B246
87
88
PH615-10
AH103
B136
B652
C313C
B644
86
85
84
83
82
81
B160
PH615-22
80
G059
78
79
H544
77
PH628-24
74
76
G004
C302A
73
P750
72
H501
H601
70
71
H912
69
H220
H221
67
68
E550
66
P732
G131
64
65
H490
H304
62
63
G090
G091
60
61
P726
P682
58
59
P684
P685
P733
PART NO.
57
56
ITEM
NO.
55
MSRP
MSRP
$26.49
$5.49 ea
$3.19 ea
$588.99 ea
$8.99/ft
$13.99 ea
$9.49 ea
$1.99 ea
$8.99/ft
$30.49 ea
$4.99 ea
$8.49 ea
$86.99 ea
$2.49 ea
$8.99/ft
$3.49 ea
$4.99 ea
$12.49 ea
$8.99/ft
$1.49 ea
$148.99 ea
$8.99 ea
$15.99 ea
$4.99 ea
$13.49 ea
$9.99 ea
$1.99 ea
$3.19 ea
$11.49 ea
$4.99 ea
$141.99 ea
$18.49 ea
$0.99 ea
$36.99 ea
$11.99 ea
$11.49 ea
$7.99/ft
$6.99 ea
$10.99 ea
$190.99 ea
3
3
$10.99 ea
$3.99 ea
$3.99 ea
$4.99 ea
$9.99 ea
$62.49 ea
$74.99 ea
3
1
1
1
1
1
3
4
1
1
2
1
1
1
1
2
2
1
1
3
2
2
1
6
1
1
2
2
2
2
1
1
6
1
1
1
1
1
1
1
QTY.
NAME
J. Cash
DATE
10/12/10
2
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
2
SCALE: 1:8
1
DO NOT
SCALE DRAWING
1005DX
SIZE DWG. NO.
C
SHEET 1 OF 2
REV
OD
PRODUCTS, INC.
858-679-1191
SPEEDSTER
mytee
TITLE:
1
A
B
C
D
E
F
1005DX SPEEDSTER
25
A
B
C
D
E
F
8
7
95
9
4
8
10
6
11
90
14
94
To vac tank
thru B235
(#45)
4
4
93
9
96
To q.d.
thru AH105
(#31)
8
5
9
3
88
86
96
8
96
89
2
7
12
11
4
To regulator
thru AH103
(#87)
1
30
90
7
90
47
85
84
87
80
13
14
4
11
91
92
To sol tank "IN"
thru B186
(#28)
To ball valve
thru B107
86
(#7)
9
81
To pressure guage "OUT"
thru B103
(#9)
7
15
83
77
16
17
82
81
To sol tank
thru B186
(#28)
18
48
19
4
6
70
71
14
72
74
76
20
48
17
73
2
17
77
78
79
6
69
21
68
22
67
66
5
5
65
15
23
16
17
24
25
4
26
4
26
*
26
27
29
26
26
30
8
To regulator
thru PH615-22
(#82)
28
To pump "IN"
thru PH615-36
(#92)
64
8
7
31
8
3
3
7
32
33
34
37
38
35
9
40
36
45
To ball valve
thru B107
(#7)
To pump "OUT"
thru AH108S
(#96)
8
9
16
39
To pump "OUT"
thru AH108s
(#96)
41
NAME
47
45
8
8
42
J. Cash
16
63
DATE
7/1/2010
2
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
23
23
2
48
56
57
58
59
49
60
52
54
53
SCALE: 1:8
1
DO NOT
SCALE DRAWING
1005DX
REV
OD
SHEET 2 OF 2
SPEEDSTER
PRODUCTS, INC.
51
55
858-679-1191
50
SIZE DWG. NO.
C
TITLE:
mytee
46
30
44
43
62
61
1
A
B
C
D
E
F
1005DX SPEEDSTER
Inline Conn.
L1 Black
GND
Green
L2 White
White / Red
Inline Conn.
Cord Input Secondary
Entry Location,
Bottom or Far Left
Cord Input Primary
Entry Location, Top or Far Right
26
Red
Black
SW-DPST
E515
C313
White
Black
White / Red
Green
Inline Conn.
Red
Vacuum Motor 1
Green
L2
Red
Black
Pressure Pump
SW-DPST
E515
Black
Inline Conn.
C302A
Inline Conn.
Green
C302A
Inline Conn.
Red
SW-DPST
E515
Inline Conn.
1005DX
Red
Black
Mytee Products
13655 Stowe Dr.
Poway, CA
Size: Letter
Number: 0000
Revision: A
92064
Time: 11:52:30 AM Sheet 1 of 1
Date: 11/30/2010
--File: C:\Compaines\GHI\Projects\Mytee Schematics\1005DX\1005DX.SCHDOC
Title
White / Red
White
White / Red
White
White
L1
GND
L2
L2 Black White
GND Green
Inline Conn.
Yellow Black L1
White
L2 Black
GND Green
Brown Black L1
White / Red
E564
Red
E512B
Lamp
Amber
Red
L1b
L2b
Pink 18 AWG
Light 2
Pink 18 AWG
Light 1 L2a
Black
L1a
Circuit Detector
White
Green
GND
L1
Blue
Vacuum Motor 2
1005DX SPEEDSTER
GENERAL INFORMATION
Dear Customer:
specify the Model and Serial Number when discussing your machine.
Congratulations on the purchase of your new Speedster® Extractor. As
you are already aware, the scene of the equipment world is becoming
more high tech, and we at Mytee Products Inc. strive to keep you on the
cutting edge with superior quality and technology.
Name Plate
The Model and Serial Number of your machine are shown on the name
plate located on the inside of the machine. This information is needed
when ordering repair parts for the machine. Use the space provided on
the front cover to note the Model and Serial Number of your machine for
future reference.
Keep in mind that the Speedster® Extractor is a machine, so neglect or
abuse will cause unnecessary damage and void the warranty. However
with simple maintenance the Speedster® will give quality performance for
many years to come.
Unpacking the Machine
When the machine is delivered, carefully inspect the shipping carton and
the machine for damage. If damage is evident, save the shipping carton so
that it can be inspected by the carrier that delivered it. Contact the carrier
immediately to file a freight damage claim.
If warranty questions arise, please consult user manual or get in touch with
your distributor. If you have questions about maintenance, replacing parts
or ordering parts, please call an authorized Mytee Products Inc. Service
Center. To see an updated list, visit our website at www.mytee.com
Caution and Warnings
Symbols
Mytee uses the symbols below to signal potentially dangerous conditions.
Always read this information carefully and take the necessary steps to
protect personnel and property.
Before you begin using, please read your manual thoroughly.
Sincerely,
Mytee Customer Care Dept.
Grounding Instructions
This machine must be grounded. If it should malfunction or breakdown,
grounding provides a path of least resistance for electrical shock. This machine is equipped with a cord having an equipment-grounding conductor
and grounding plug. The plug must be plugged into an appropriate outlet
that is properly installed in accordance with all local code and ordinances.
Do not remove ground pin; if missing, replace plug before use.
Is used to warn of immediate hazards that will cause severe personal
injury or death.
Is used to call attention to a situation that could cause severe personal
injury.
Improper connection of the equipment-grounding conductor can result in a
risk of electric shock. Check with a qualified electrician or service person
if you are in doubt as to whether the outlet is properly grounded. Do not
modify the plug provided with the machine. If it will not fit the outlet, have a
proper outlet installed by a qualified electrician.
Is used to call attention to a situation that could cause minor personal
injury or damage to the machine or other property. When using an electrical appliance, basic precautions should always be followed, including the
following: Read all instructions before using this machine. This product is
intended for commercial use only.
This appliance is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in Figure 1 below. A temporary
adapter illustrated in Figures 2 and 3 may be used~to connect this plug to
a 2-pole receptacle as shown in Figure 2 if a properly grounded outlet is
not available. The temporary adapter should be used only until a properly
grounded outlet (Figure 1) can be installed by a qualified electrician. The
green colored rigid ear, tab or the like extending from the adapter must be
connected to a permanent ground such as a properly grounded outlet box
cover. Whenever the adapter is used, it must be held in place by a metal
screw. Grounding adapters are not approved for use in Canada.
To reduce the risk of fire, electrical shock, or injury:
1. Read all instructions before using equipment.
2. Use only as described in this manual. Use only manufacturer’s recommended attachments.
3. Always unplug power cord from electrical outlet before attempting any
adjustments or repairs.
4. Do not unplug by pulling on cord. To unplug, grasp the plug, not the
cord.
5. Do not pull or carry by cord. Do not close a door on cord or pull cord
around sharp edges or corners.
6. Do not run appliance over cord. Keep cord away from heated surfaces.
7. Do not use with damaged cord or plug. If cord is damaged, repair immediately.
8. Do not use outdoors or on wet surfaces and or standing water.
9. Always unplug or disconnect the appliance from power supply when not
in use.
10. Do not allow to be used as a toy. Close attention is necessary when
used by or near children.
11. Do not use in areas where flammable or combustible material may be
present.
12. Do not leave the unit exposed to harsh weather elements. Temperatures below freezing may damage components and void warranty.
13. Use only the appropriate handles to move and lift unit. Do not use any
other parts of this machine for this purpose.
14. Keep hair, loose clothing, fingers, and all parts of the body away from
all openings and moving parts.
15. Use extra care when using on stairs.
16. To reduce the risk of fire or electric shock, do not use this machine with
a solid-state speed control device.
Replace the plug if the grounding pin is damaged or broken.
The Green (or GreenYellow) wire in the cord is the grounding wire. When
replacing a plug, this wire must be attached to the grounding pin only.
DO NOT use extension cords.
Please Note for America use only
Grounded Outlet
Adapter
Metal
Screw
Grounding Pin
Grounded Outlet Box
Figure 1
Figure 2
Tab for Grounding
Screw
Figure 3
Parts and Service
Repairs, when required, should be performed by Mytee service personnel or Mytee authorized Service Center using Mytee original replacement
parts and accessories. Call Mytee for repair parts or service. Please
27
GENERAL INFORMATION
After Use
17. The voltage and frequency indicated on the name plate must correspond to the wall receptacle supply voltage.
18. When cleaning and servicing the machine, local or national regulations
may apply to the safe disposal of liquids which may contain: chemicals,
grease, oil, acid, alkalines, or other dangerous liquids.
19. Do not leave operating unattended.
1. Before storing machine, drain, rinse and dry tanks and vacuum hose of
water and solution.
2. Store in a dry are in the upright position.
3. Open recover tank cover to promote air circulation.
4. Store indoors in a dry area. If storing in freezing temperatures, make
sure the machine and solution system are completely drained and dry.
Preparation
Maintenance Schedule
1. Remove furniture and other items from the area you are going to clean.
2. Vacuum carpet and upholstery, and remove debris.
3. Protect cabinets, walls and painted surfaces with drop cloths or plastic.
4. Inspect power cords for damages.
Latches are located in back to open tank for internal maintenance. To
keep machine in good working condition, follow machine’s daily and
weekly maintenance procedures. Check valves and relief valves should be
replaced annually.
Operating Instructions
1. Fill the solution tank.
2. Attach one end of a solution hose to a wand or other tool, the other end
to the Speedster’s® front quick disconnect.
3. Attach one end of a vacuum hose to the tool, the other end to the
Speedster’s® Cuff-Lynx™ vacuum hose port.
4. Plug in power cords.
• 1000DX and 1000DX-200 models – Plug single cord into single, 20A
grounded wall outlet.
• 1001DX, 1001DX-200 models – Using two separate circuits/breakers,
plug the left power cord into 20A grounded wall outlet to turn on Vac 2 and
Heater 2. Plug the right power cord into separate 20A grounded wall outlet
to turn on Vac 1, Heater 1 and Pump.
• 1003DX models – Using two separate circuits/breakers, plug the left
power cord into 20A grounded wall outlet to turn on Vac 2 and Heater 2.
Plug the right power cord into separate 20A grounded wall outlet to turn on
Vac 1, Heater 1 and Pump.
• 1005DX models – Using two separate circuits/breakers, plug the left
power cord into 20A grounded wall outlet to turn on Vac 2. Plug the right
power cord into separate 20A grounded wall outlet to turn on Vac 1 and
Pump.
The amber light indicator on the switch plate will illuminate brightly when
cords are plugged into two separate circuits. Do not use extension cords
longer than 50 feet.
5. Turn on switches.
• 1000DX, 1000DX-200, 1005DX models – Turn on Vac 1, Vac 2 and
Pump switches.
• 1001DX, 1001DX-200 and 1003DX – Turn on Vac 1, Vac 2 and Pump
switches. Turn on Heater switch if heat is being used. Wait several
minutes for water to heat. Heater switch has three positions: Off (middle);
1,000 watts using one heater (left); and 2,000 watts using two heaters
(right). Red lights on panel display indicate watts selected: one light =
1,000 watts; two lights = 2,000 watts; no lights = heaters are off.
6. 1003DX and 1005DX models – Prime Valve and Pressure Regulator
are located on the lower front of the extractor. To prime the pump, turn the
valve to the Prime position for 30 seconds, then turn horizontally to the
Run position. Turn the Pressure Regulator to the left to decrease the water
pressure. Turn to the right to increase water pressure. Level will be visible
on the pressure gauge. Monitor while adjusting, using Pressure Gauge on
Switch Panel.
7. Begin cleaning. Make two dry passes to every wet pass. Work away
from cords to avoid damage. To clean heavily soiled areas, repeat cleaning from a different direction.
8. Use a foam control solution in the recovery tank to prevent motor damage and check for foam build-up in recovery and solution tanks.
9. Empty the recovery tank as needed when the internal ball float automatically shuts off the vacuum. Attach the 45˚ drain elbow to the drain
spout in back. Lift up the dump valve and empty tank.
10. To relieve water pressure from the solution hose before disconnecting
it, squeeze the tool’s trigger five seconds after turning the power switches
off.
11. Once machine is off, unplug power cords. Remove solution and
vacuum hoses. Empty the recovery tank by attaching the 45˚ drain elbow
to the drain spout in back. Lift up the dump valve and empty tank.
12. 1003DX and 1005DX models – Water remaining in the solution tank
can be emptied by turning the Prime Valve to the right to move water into
the recovery tank. Empty recovery tank.
Maintenance item
Daily
Clean and inspect tanks.
Clean and inspect hoses.
Check and clean internal filters by twisting
off, rinsing with clean water and replacing.
Check power supply cable.
Clean machine with all-purpose cleaner
and cloth.
Check spray nozzles.
Flush solution system with Mytee® System
Maintainer.
Remove and float shut-off screen from
tank and clean. Simply pull off.
Inspect vacuum hoses for holes and loose
cuffs.
Inspect spray pattern for clogging. If
clogged, remove spray tips and soak them
in a recommended liquid neutralizer for
up to six hours. To remove spray tip, twist
spray tip body counter-clockwise.
Lubricate wheels with water resistant oil.
Inspect machine for water leaks and loose
hardware.
x
x
x
Once a week
x
x
x
x
x
x
x
x
x
Trouble Shooting
There is no power.
1. Plug machine in proper outlet.
2. If using two cords, make sure each is plugged into a separate circuit.
3. Check circuit breaker. Reset circuit breaker, other items should not run
on the same circuit as the machine. Outlet must be a 20-amp circuit.
Pump does not work properly
1. Snap quick disconnects firmly together.
2. Check solution tank; may be empty.
3. Jets clogged, remove jet and flush clean.
4. Filters clogged, remove filters and rinse clean with water.
5. Heater is blocked; flush out with Mytee’s® System Maintainer.
6. If brass check valve is stuck, replace valve.
7. Check pump wire. May need to reconnect wire.
8. Switch plate may need to be replaced.
9. If pump motor brushes are worn, replace pump.
1001DX, 1001DX-200 or 1003DX heater does not work properly
1. If sensor mounted on the heater has popped, reset sensor by pushing
in button.
2. Heating element may need to be replaced.
Vacuum motor does not work properly
1. Check that hose is tightly connected.
2. Close drain hose valve completely.
3. Secure the vacuum tank tightly.
4. If ball float is shut off, empty vacuum tank of all wastewater.
5. Make sure ball float is firmly installed on the elbow.
6. If water is coming out of the vacuum motor, use a low foaming
detergent.
7. Clean upholstery tool or floor wand jets.
28
GENERAL INFORMATION
FAQs
HEREOF. MYTEE SHALL IN NO WAY BE RESPONSIBLE FOR THE
PROPER USE AND APPLICATION OF THE GOODS. MYTEE NEITHER
ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME
FOR MYTEE ANY OTHER LIABILITY IN CONNECTION WITH THE
SALE OF MYTEE’S GOODS. THIS LIMITED WARRANTY POLICY MAY
BE CHANGED OR WITHDRAWN BY MYTEE AT ANY TIME WITHOUT
NOTICE.
Q: How much do the Speedster® Series extractors weigh and what are
the dimensions?
A: All Speedsters
Machine Dimensions: 28” x 18 ¼” x 40”
Shipping Dimensions: 29 ½” x 19 ¼” x 46 ½”
1000DX – Machine Weight: 83 lbs.
Shipping Weight: 104 lbs.
LIMITATION OF DAMAGES: THE REMEDY OF REPLACEMENT OR
REPAIR OF ANY DEFECTIVE GOODS SHALL BE THE EXCLUSIVE
REMEDY UNDER ANY WARRANTY MADE BY MYTEE, WHETHER
EXPRESS OR IMPLIED. IN NO EVENT SHALL MYTEE BE LIABLE FOR
ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, PROPERTY
DAMAGES, OR PERSONAL INJURIES.
1000DX-200 – Machine Weight: 83 lbs.
Shipping Weight: 104 lbs.
1001DX – Machine Weight: 94 lbs.
Shipping Weight: 124 lbs.
All limited warranties are void for, and Mytee does not warrant in any way,
any product that evidences misapplication, improper installation, abuse,
lack of maintenance, negligence in use or care, abnormal use, alteration
of design, modification, use of incompatible or corrosive chemicals, use in
a rental service, and/or servicing, installation of parts, or repairs by anyone
other than Mytee or a Mytee authorized distributor or service center. Mytee
may make changes in products it manufactures and markets at any time;
these changes are made without obligation to change, retrofit, or upgrade
any product previously sold or manufactured.
1001DX-200 – Machine Weight: 94 lbs.
Shipping Weight: 124 lbs.
1003DX – Machine Weight: 122 lbs.
Shipping Weight: 150 lbs.
1005DX – Machine Weight: 113 lbs.
Shipping Weight: 140 lbs.
Mytee has no obligation to honor the limited warranties set forth herein
unless the original purchaser, promptly upon discovering the warranty
claim and prior to continuing to use the product, contacts Mytee or a
Mytee authorized distributor or service center to describe the claim and to
receive and follow instructions for documenting and resolving the claim.
In addition, the purchaser must provide the product to which the claim
applies to Mytee or a Mytee authorized distributor or service center for a
thorough inspection. In addition, the purchaser must provide/return the
product intact, unmodified, with all of its original parts.
Q: What comes standard with Speedsters™ extractors?
A: Hose hanger with four screws, two Cuff-Lynx™ Model Numbers: H141
Reducer and H110 Coupler Swivel, and 45˚ drain elbow.
Q: Does Mytee® recommend tools for this machine?
A: All upholstery tools and wands can be used with the Speedster® series.
Q: Is there anything I can do to increase the expected life of my machine?
A: Running the vacuum motors with the tank empty and lid off will allow
excess moisture in the vacs to dry off. You should also run Mytee’s®
System Maintainer through the system to keep the hoses, pump, and
heater clean and free of debris..
If any provision or portion of this limited warranty policy is found to be
unenforceable, then the remaining provisions and portions shall remain
valid and enforceable. If any provision or portion of this limited warranty
policy is found to be limited by law, then that provision or portion shall
be construed to make it effective within the bounds of law. For example,
if there are legal limitations on the duration of warranties, the warranties
made herein shall be construed to have the minimum duration required by
law, or, if there are legal limitations of exclusion of remedies, the exclusions made herein shall be construed to apply to the fullest extent possible
without violating the law.
Warranty
MYTEE LIFETIME LIMITED WARRANTY POLICY
Mytee Products, Inc. endeavors to provide high quality products and
product support to its customers and therefore backs up all of its new
products purchased from Mytee Products Inc. (“Mytee”) or any authorized
Mytee distributor/service center with this lifetime limited warranty. This
limited warranty begins on the date of the customer’s purchase and is
valid and available to the original purchaser with proof of purchase, and is
not transferable. Mytee’s products are for commercial use only and are not
intended for personal, family or household uses.
The validity, construction and performance of this warranty policy shall be
governed by the laws of the State of California, without respect to conflicts
of laws principles. The exclusive jurisdiction of any legal action arising
from or related to this warranty policy shall be in the State of California and
no legal action shall be commenced elsewhere.
HOUSING LIMITED LIFETIME WARRANTY: Mytee warrants for life that
its rotationally-molded housings will be free from manufacturing defects.
This warranty covers the cost of replacement or repair only and does not
cover shipping or labor costs.
Return Material Authorization Procedure
It is the responsibility of any Authorized Service Center (ASC) or Distributor with written authorization to ensure the Customers equipment is
repaired as soon as possible. Only Mytee Products Inc. or it’s authorized
dealers with written authorization, service centers, and agents may make
warranty repairs on these products. All others do so at their own risk and
expense.
WEAR PARTS 90-DAY LIMITED WARRANTY: Mytee will replace all wear
parts for 90 days from the date of original purchase. “Wear parts” are
items which wear out as a result of usage or the passage of time and are
consumed despite attempts to maintain them, such as gaskets, wheels,
brass, cords, wires, electrical terminals, hoses, switches, thermostats,
plastisol parts, filters, bearings, brushes, solenoids, o-rings, bulbs, heating elements, castors, or other parts deemed wear items in Mytee’s sole
discretion. This warranty covers the cost of replacement only and does not
cover shipping or labor costs.
The Distributor must follow Mytee Products, Inc. standard RMA procedure:
1. When a repair falls within the Warranty time period for a piece of equipment, the Distributor will fill out a RMA/Warranty claim form. This form will
act as a repair order to replace any defective parts.
HOWEVER, OTHER THAN SET FORTH HEREIN, MYTEE GIVES NO
WARRANTY, EXPRESS OR IMPLIED, AS TO DESCRIPTION, QUALITY, MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE,
PRODUCTIVENESS, INFRINGEMENT, OR OTHER MATTER, OF ANY
GOODS WHICH MYTEE SHALL SUPPLY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
2. All defective parts must be returned to Mytee Products, Inc. with the
RMA/claim form for evaluation at the customer’s expense. This shipping is
non-refundable. All warranty claims are subject to an evaluation by Mytee
Products, Inc. to determine if warranty will be approved. Any credit for
29
repair and/or parts will only be issued upon evaluation and approval from
Mytee Products, Inc.
3. When Warranty is approved, the Distributor’s account will be credited
for the replacement part(s). Mytee Products, Inc. will ship the warranted
replacement part(s) to the Distributor prepaid. If Warranty is denied the
Distributor’s account will not be credited for any parts sent for this claim.
NOTES
30
NOTES
31
Mytee Products Inc.
13655 Stowe Dr.
Poway, Ca. 92064
www.mytee.com
PH 858.679.1191
F X 858.679.7814
© 2010 Mytee Products Inc.
Printed in the U.S.A.
32
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising