QuickSpecs
HP 6600 Switch Series
Overview
HP 6600-24G-4XG Switch
J9264A
Key features
Enhanced for data center server access layer
Front-to-back, reversible airflow
Redundant, hot-swappable power supplies and fans
64K MAC address scalability
Consistent ProVision ASIC-based switch fabric
Product overview
The HP 6600 Switch Series consists of advanced data center server edge switches. The 6600 Switch Series includes 10/100/1000BASET and 10GbE SFP+ 1U rackmount switches enhanced for server edge connectivity with front-to-back (reversible) airflow, redundant
hot-swappable power, and redundant hot-swappable fans. The foundation for the switch series is a purpose-built, programmable
ProVision ASIC that allows the most demanding networking features, such as quality of service (QoS) and security, to be implemented
in a scalable yet granular fashion. With a variety of connectivity interfaces and expanded buffering, the HP 6600 Switch Series offers
excellent investment protection, flexibility, and scalability, as well as ease of deployment and reduced operational expense.
Features and benefits
NEW Software-defined networking
OpenFlow
is a key technology enabling software-defined networking by allowing the separation of data (packet forwarding) and control
(routing decision) paths
Quality of Service (QoS)
Layer 4 prioritization
enables prioritization based on TCP/UDP port numbers
Class of Service (CoS)
sets the IEEE 802.1p priority tag based on IP address, IP Type of Service (ToS), Layer 3 protocol, TCP/UDP port number, source
port, and DiffServ
Bandwidth shaping:
Port-based rate limiting: provides per-port ingress-/egress-enforced increased bandwidth
Classifier-based rate limiting: uses an access control list (ACL) to enforce increased bandwidth for ingress traffic on each
port
Reduced bandwidth: provides per-port, per-queue egress-based reduced bandwidth
Advanced classifier-based QoS
classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information; applies QoS policies such as setting priority
level and rate limit to selected traffic on a per-port or per-VLAN basis
Traffic prioritization
allows real-time traffic classification into eight priority levels mapped to eight queues
Data center optimized
Front-to-back airflow
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 1
QuickSpecs
HP 6600 Switch Series
Overview
designed to be collocated at the top of a server rack, the 6600 Switch Series supports front-to-back airflow (mechanically
reversible) to support hot aisle/cold aisle configurations; the N+N fan tray is also hot-swappable, allowing easy replacement in
the rack
Modular internal power supplies
support redundant, hot-swappable power supply configurations (units ship with one supply); power load is shared across dual
supplies
Server-to-switch distributed trunking
supports Layer 2 LACP groups from a single server across two different switches for active-active server NIC teaming
configurations
Power down idle ports
save power by powering down blocks of idle Gigabit and 10GbE ports; idle ports can be reinitialized without rebooting; available
on 6600-24XG and 6600-48G-4XG models
Out-of-band management
remotely monitors and manages switch via Ethernet out-of-band management port; eliminates the need for terminal server
network; available on 6600-24XG and 6600-48G-4XG models
Deployment/Serviceability
data connectivity and management ports are all front-side accessible, and power supplies and fan trays are rear-side accessible,
allowing for easy maintenance and in-rack serviceability
Management
Remote intelligent mirroring
mirrors selected ingress/egress traffic based on ACL, port, MAC address, or VLAN to a local or remote HP 8200 zl, 6600, 6200 yl,
5400 zl, or 3500 Switch located anywhere on the network
RMON, XRMON, and sFlow v5
provide advanced monitoring and reporting capabilities for statistics, history, alarms, and events
Uni-Directional Link Detection (UDLD)
monitors a cable between two switches and shuts down the ports on both ends if the cable is broken, turning the bidirectional
link into a unidirectional one; this prevents network problems such as loops
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
advertises and receives management information from adjacent devices on a network, facilitating easy mapping by network
management applications
Management simplicity
provided by common networking features and CLI implementation (common across HP 8200 zl, 6600, 6200 yl, 5400 zl, and 3500
Switches)
Command authorization
leverages RADIUS to link a custom list of CLI commands to an individual network administrator's login; an audit trail documents
activity
Friendly port names
allow assignment of descriptive names to ports
Multiple configuration files
can be stored to the flash image
Dual flash images
provide independent primary and secondary operating system files for backup while upgrading
NEW Comware CLI
Comware-compatible CLI
bridges the experience of HP Comware CLI users who are using the HP ProVision software CLI
Display and fundamental Comware CLI commands
are embedded in the switch CLI as native commands; display output is formatted as on Comware-based switches, and
fundamental commands provide a Comware-familiar initial switch setup
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 2
QuickSpecs
HP 6600 Switch Series
Overview
Configuration Comware CLI commands
when Comware commands are entered, CLI help is elicited to formulate the correct ProVision software CLI command
Connectivity
Auto-MDIX
automatically adjusts for straight-through or crossover cables on all 10/100 and 10/100/1000 ports
Jumbo frames
on Gigabit Ethernet and 10-Gigabit Ethernet ports, jumbo frames allow high-performance remote backup and disaster-recovery
services
IPv6:
IPv6 host: enables switches to be managed in an IPv6 network
Dual stack (IPv4 and IPv6): transitions from IPv4 to IPv6, supporting connectivity for both protocols
MLD snooping: forwards IPv6 multicast traffic to the appropriate interface
IPv6 ACL/QoS: supports ACL and QoS for IPv6 network traffic
IPv6 routing: supports static and OSPFv3 routing protocols
6in4 tunneling: supports encapsulation of IPv6 traffic in IPv4 packets
Performance
High-speed, high-capacity architecture
based on the purpose-built ProVision ASICs to provide superior system performance and scalability
Selectable queue configurations
allows for increased performance by selecting the number of queues and associated memory buffering that best meet the
requirements of the network applications
Resiliency and high availability
IEEE 802.3ad Link Aggregation Control Protocol (LACP) and HP port trunking
support up to 60 trunks, each with up to eight links (ports) per trunk
IEEE 802.1s Multiple Spanning Tree
provides high link availability in multiple VLAN environments by allowing multiple spanning trees; provides legacy support for
IEEE 802.1d and IEEE 802.1w
Virtual Router Redundancy Protocol (requires Premium License)
allows groups of two routers to dynamically back each other up to create highly available routed environments
Spares simplicity
is made possible through the use of common power supplies, fan trays, and transceivers
Distributed trunking
enables loop-free and redundant network topology without using Spanning Tree Protocol; allows a server or switch to connect
to two switches using one logical trunk for redundancy and load sharing
Uplink Failure Detection
provides active-standby network path redundancy for servers that are configured for active-standby NIC teaming
Layer 2 switching
HP switch meshing
dynamically load balances across multiple active redundant links to increase available aggregate bandwidth
GARP VLAN Registration Protocol
allows automatic learning and dynamic assignment of VLANs
IEEE 802.1ad Q-in-Q (requires Premium License)
increases the scalability of an Ethernet network by providing a hierarchical structure; connects multiple LANs on a high-speed
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 3
QuickSpecs
HP 6600 Switch Series
Overview
campus or metro network
IEEE 802.1v protocol VLANs
isolate select non-IPv4 protocols automatically into their own VLANs
Rapid Per-VLAN Spanning Tree (RPVST+)
allows each VLAN to build a separate spanning tree to improve link bandwidth usage; is compatible with PVST+
Layer 3 services
Loopback interface address
defines an address in Routing Information Protocol (RIP) and Open Standard Path First (OSPF), improving diagnostic capability
User Datagram Protocol (UDP) helper function
allows UDP broadcasts to be directed across router interfaces to specific IP unicast or subnet broadcast addresses and prevents
server spoofing for UDP services such as DHCP
Route maps
provide more control during route redistribution; allow filtering and altering of route metrics
Layer 3 routing
Static IP routing
provides manually configured routing for both IPv4 and IPv6 networks
Routing Information Protocol (RIP)
provides RIPv1 and RIPv2 routing
OSPF (requires Premium License)
provides OSPFv2 for IPv4 routing and OSPFv3 for IPv6 routing
BGP (requires Premium License): provides IPv4 Border Gateway routing protocol that is scalable, robust, and flexible
Security
Source-port filtering
allows only specified ports to communicate with each other
RADIUS/TACACS+
eases switch management security administration by using a password authentication server
Secure Shell
encrypts all transmitted data for secure remote CLI access over IP networks
Port security: allows access only to specified MAC addresses, which can be learned or specified by the administrator
MAC address lockout
prevents particular configured MAC addresses from connecting to the network
Detection of malicious attacks
monitors 10 types of network traffic and sends a warning when an anomaly that potentially can be caused by malicious attacks
is detected
Secure FTP
allows secure file transfer to and from the switch; protects against unwanted file downloads or unauthorized copying of a switch
configuration file
Switch management logon security
can require either RADIUS or TACACS+ authentication for secure switch CLI logon
Secure management access
securely encrypts all access methods (CLI, GUI, or MIB) through SSHv2, SSL, and/or SNMPv3
ICMP throttling
defeats ICMP denial-of-service attacks by enabling any switch port to automatically throttle ICMP traffic
Virus throttling
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 4
QuickSpecs
HP 6600 Switch Series
Overview
detects traffic patterns typical of worm-type viruses and either throttles or entirely prevents the virus from spreading across the
routed VLANs or bridged interfaces without requiring external appliances
STP BPDU port protection
blocks Bridge Protocol Data Units (BPDUs) on ports that do not require BPDUs, preventing forged BPDU attacks
Dynamic IP lockdown
works with DHCP protection to block traffic from unauthorized hosts, preventing IP source address spoofing
DHCP protection
blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks
Dynamic ARP protection
blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of network data
USB Secure Autorun (requires HP PCM+)
deploys, diagnoses, and updates a switch using a USB flash drive; works with a secure credential to prevent tampering
STP Root Guard
protects the root bridge from malicious attack or configuration mistakes
Management Interface Wizard
helps secure management interfaces such as SNMP, telnet, SSH, SSL, Web, and USB at the desired level
Access control lists (ACLs)
provide filtering based on the IP field, source/destination IP address/subnet, and source/destination TCP/UDP port number on a
per-VLAN or per-port basis
Multiple user authentication methods:
Multiple IEEE 802.1X users per port: authenticates multiple IEEE 802.1X users per port
Web-based authentication: authenticates from Web browser for clients that do not support IEEE 802.1X supplicant
MAC-based authentication: client is authenticated with the RADIUS server based on client's MAC address
Concurrent IEEE 802.1X, Web, and MAC authentication schemes per port: switch port accepts up to 32 sessions of IEEE
802.1X, Web, and MAC authentications
Switch CPU protection
provides automatic protection against malicious network traffic trying to shut down the switch
Identity-driven ACL
enables implementation of a highly granular and flexible access security policy specific to each authenticated network user
Secure Sockets Layer (SSL)
encrypts all HTTP traffic, allowing secure access to the browser-based management GUI in the switch
Security banner
displays a customized security policy when users log in to the switch
Multicast support
IP multicast routing (requires Premium License)
includes PIM Sparse and Dense modes to route IP multicast traffic
IP multicast snooping (data-driven IGMP)
automatically prevents flooding of IP multicast traffic
Convergence
NEW Auto VLAN configuration for voice
RADIUS VLAN
uses a standard RADIUS attribute and LLDP-MED to automatically configure a VLAN for IP phones
CDPv2
uses CDPv2 to configure legacy IP phones
Warranty and support
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 5
QuickSpecs
HP 6600 Switch Series
Overview
Lifetime warranty
for as long as you own the product with advance replacement and next-business-day delivery (available in most countries)†
Electronic and telephone support
limited electronic and telephone support is available from HP; to reach our support centers, refer to
www.hp.com/networking/contact-support; for details on the duration of support provided with your product purchase, refer to
www.hp.com/networking/warrantysummary
Software releases
to find software for your product, refer to www.hp.com/networking/support; for details on the software releases available with
your product purchase, refer to www.hp.com/networking/warrantysummary
†HP warranty includes repair or replacement of hardware for as long as you own the product, with next business day advance
replacement (available in most countries). The disk drive included with HP AllianceOne Advanced Services and Services zl Modules, HP
Threat Management Services zl Module, HP AllianceOne Extended zl Module with Riverbed Steelhead, HP MSM765zl Mobility Controller
and HP Survivable Branch Communication zl Module powered by Microsoft Lync has a five-year hardware warranty. For details, refer to
the Software license and hardware warranty statements at www.hp.com/networking/warranty.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 6
QuickSpecs
HP 6600 Switch Series
Configuration
Build To Order:
BTO is a standalone unit with no integration. BTO products ship standalone are not part of a CTO or Rack-Shippable solution.
HP 6600-24G-4XG Switch
20 autosensing 10/100/1000 port
4 open mini-GBIC slots
4 open 10-GbE SFP+ transceiver slots
min=0 \ max=4 SFP+ Transceivers
1 - J9269A HP E6600 Switch Power Supply Included
1U - Height
J9264A
See Configuration
Note:1, 2, 3, 4
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
J9264A#B2B
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
J9264A#B2C
Configuration Rules:
Note 1
Note 2
Note 3
The following SFP+ Transceivers install into this switch:
HP X132 10G SFP+ LC ER Transceiver
HP X132 10G SFP+ LC LR Transceiver
HP X132 10G SFP+ LC LRM Transceiver
HP X132 10G SFP+ LC SR Transceiver
HP X242 SFP+ SFP+ 1m Direct Attach Cable
HP X242 SFP+ SFP+ 3m Direct Attach Cable
HP X242 SFP+ SFP+ 7m Direct Attach Cable
HP X244 XFP SFP+ 1m Direct Attach Cable
HP X244 XFP SFP+ 3m Direct Attach Cable
HP X244 XFP SFP+ 5m Direct Attach Cable
HP X242 SFP+ 10m DAC Cable
HP X242 SFP+ 15m DAC Cable
J9153A
J9151A
J9152A
J9150A
J9281B
J9283B
J9285B
J9300A
J9301A
J9302A
J9286B
J9287B
The following Transceivers install into this switch:
HP X121 1G SFP LC SX Transceiver
HP X121 1G SFP LC LX Transceiver
HP X121 1G SFP LC LH Transceiver
HP X121 1G SFP RJ45 T Transceiver
HP X112 100M SFP LC BX-D Transceiver
HP X112 100M SFP LC BX-U Transceiver
HP X122 1G SFP LC BX-D Transceiver
HP X122 1G SFP LC BX-U Transceiver
HP X111 100M SFP LC FX Transceiver
J4858C
J4859C
J4860C
J8177C
J9099B
J9100B
J9142B
J9143B
J9054C
Localization required. (See Localization Menu for list.)
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 7
QuickSpecs
HP 6600 Switch Series
Configuration
Note 4
Localization required on orders without #B2B or #B2C options.
Remarks:
Drop down under power supply should offer the following options and results:
Switch/Router/Power Supply to PDU Power Cord - #B2B in North America, Mexico, Taiwan, and Japan or #B2C ROW.
(Watson Default B2B or B2C for Rack Level CTO)
Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson Default for BTO and Box Level CTO)
Rack Level Integration CTO Models
HP 6600-24G-4XG Switch
20 autosensing 10/100/1000 port
4 open mini-GBIC slots
min=0 \ max=4 SFP Transceivers
4 open 10-GbE SFP+ transceiver slots
min=0 \ max=4 SFP+ Transceivers
2 - Power Supply Slots
1 - J9269A HP E6600 Switch Power Supply Included
1U - Height
J9264A
See Configuration
Note:1, 2, 3
HP 6600-24G-4XG Factory Integ Switch
J9264AZ
See Configuration
Note:1, 2, 3
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
J9264AZ#B2B
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
J9264AZ#B2C
HP 6600-24XG Switch
24 open 10-GbE SFP+ transceiver slots
min=0 \ max=24 SFP+ Transceivers
2 - Power Supply Slots
1 - J9269A HP E6600 Switch Power Supply Included
1U - Height
J9265A
See Configuration
Note:1, 3
Configuration Rules:
Note 1
The following SFP+ Transceivers install into this switch:
HP X132 10G SFP+ LC ER Transceiver
HP X132 10G SFP+ LC LR Transceiver
HP X132 10G SFP+ LC LRM Transceiver
HP X132 10G SFP+ LC SR Transceiver
HP X242 SFP+ SFP+ 1m Direct Attach Cable
HP X242 SFP+ SFP+ 3m Direct Attach Cable
DA - 13267 EMEA — Version 20 — February 4, 2014
J9153A
J9151A
J9152A
J9150A
J9281B
J9283B
Page 8
QuickSpecs
HP 6600 Switch Series
Configuration
Note 2
Note 3
HP X242 SFP+ SFP+ 7m Direct Attach Cable
HP X244 XFP SFP+ 1m Direct Attach Cable
HP X244 XFP SFP+ 3m Direct Attach Cable
HP X244 XFP SFP+ 5m Direct Attach Cable
HP X242 SFP+ 10m DAC Cable
HP X242 SFP+ 15m DAC Cable
J9285B
J9300A
J9301A
J9302A
J9286B
J9287B
The following SFP Transceivers install into this switch:
HP X121 1G SFP LC SX Transceiver
HP X121 1G SFP LC LX Transceiver
HP X121 1G SFP LC LH Transceiver
HP X112 100M SFP LC BX-D Transceiver
HP X112 100M SFP LC BX-U Transceiver
HP X122 1G SFP LC BX-D Transceiver
HP X122 1G SFP LC BX-U Transceiver
HP X111 100M SFP LC FX Transceiver
J4858C
J4859C
J4860C
J9099B
J9100B
J9142B
J9143B
J9054C
If switch is ordered #0D1 then 464794-B21#0D1 - 10K Rack Kit Assembly is required.
Remarks:
Drop down under power supply should offer the following options and results:
Switch/Router/Power Supply to PDU Power Cord - #B2B in North America, Mexico, Taiwan, and Japan or #B2C ROW.
(Watson Default B2B or B2C for Rack Level CTO)
Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson Default for BTO and Box Level CTO)
Enter the following menu selections as integrated to the CTO Model X server above if order is factory built.
Transceivers
SFP Transceivers
HP X111 100M SFP LC FX Transceiver
J9054C
HP X112 100M SFP LC BX-D Transceiver
J9099B
HP X112 100M SFP LC BX-U Transceiver
J9100B
HP X121 1G SFP LC LH Transceiver
J4860C
HP X121 1G SFP LC LX Transceiver
J4859C
HP X121 1G SFP LC SX Transceiver
J4858C
HP X122 1G SFP LC BX-D Transceiver
J9142B
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 9
QuickSpecs
HP 6600 Switch Series
Configuration
HP X122 1G SFP LC BX-U Transceiver
J9143B
SFP+ Transceivers
HP X132 10G SFP+ LC ER Transceiver
J9153A
HP X132 10G SFP+ LC LR Transceiver
J9151A
HP X132 10G SFP+ LC LRM Transceiver
J9152A
HP X132 10G SFP+ LC SR Transceiver
J9150A
HP X242 10G SFP+ SFP+ 1m DAC Cable
J9281B
HP X242 10G SFP+ SFP+ 3m DAC Cable
J9283B
HP X242 10G SFP+ SFP+ 7m DAC Cable
J9285B
HP X244 10G XFP SFP+ 1m DAC Cable
J9300A
HP X244 10G XFP SFP+ 3m DAC Cable
J9301A
HP X244 10G XFP SFP+ 5m DAC Cable
J9302A
HP X242 10G SFP+ 10m DAC Cable
J9286B
HP X242 10G SFP+ 15m DAC Cable
J9287B
Internal Power Supplies
See Models for number of slots and what's included with each base.
HP 6600 Switch Power Supply
J9269A
See Configuration
Note:1, 2, 3
HP 6600 Fact Integ Switch Power Supply
J9269AZ
See Configuration
Note:1
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
J9269AZ#B2B
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
J9269AZ#B2C
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 10
QuickSpecs
HP 6600 Switch Series
Configuration
Configuration Rules:
Note 1
If 2 or more power supplies are selected they must be the same Sku number.
Note 2
Localization required. (See Localization Menu for list.)
Note 3
Localization required on orders without #B2B or #B2C options.
Remarks:
Drop down under power supply should offer the following options and results:
Switch/Router/Power Supply to PDU Power Cord - #B2B in North America, Mexico, Taiwan, and Japan or #B2C ROW.
(Watson Default B2B or B2C for Rack Level CTO)
Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson Default for BTO and Box Level CTO)
Cables
Multi-Mode Cables
HP .5m Multi-mode OM3 LC/LC FC Cable
AJ833A
HP 1m Multi-mode OM3 LC/LC FC Cable
AJ834A
HP 2 m Multimode OM3 LC/LC FC Cable
AJ835A
HP 5 m Multimode OM3 LC/LC FC Cable
AJ836A
HP 15 m Multimode OM3 LC/LC FC Cable
AJ837A
HP 30 m Multimode OM3 LC/LC FC Cable
AJ838A
HP 50 m Multimode OM3 LC/LC FC Cable
AJ839A
HP Premier Flex LC/LC OM4 2f 1m Cbl
QK732A
HP Premier Flex LC/LC OM4 2f 2m Cbl
QK733A
HP Premier Flex LC/LC OM4 2f 5m Cbl
QK734A
HP Premier Flex LC/LC OM4 2f 15m Cbl
QK735A
HP Premier Flex LC/LC OM4 2f 30m Cbl
QK736A
HP Premier Flex LC/LC OM4 2f 50m Cbl
QK737A
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 11
QuickSpecs
HP 6600 Switch Series
Configuration
Switch Enclosure Options
E6600 Fan Tray
HP 6600 Switch Fan Tray
J9271A
HP 6600 Factory Integ Switch Fan Tray
J9271AZ
License
HP 6600 Switch Premium License
J9305A
Mounting Kit
HP 6600 Series Switch Rack Kit
J9469A
See Configuration
Note:1
Rack Mounting Kit
HP Factory Rack mount Shelf Kit
AB469A
See Configuration
Note:2
HP 2610 Rail Kit
464794-B21
See Configuration
Note:2
HP 6600-24XG/48G/48G-4XG Swch AirPlm Kit
J9480A
HP 6600-24XG/48G/48G-4XG Integ AirPlm Kt
J9480AZ
HP 6600-24G/24G-4XG Swch Air Plenum Kit
J9481A
HP 6600-24G/24G-4XG Swch Air Plenum Kit
J9481AZ
Cofiguration Rules:
Note 1
For field racking of the 6600 series switches the J9469A is required. (Not supported for Factory Racking).
Note 2
For factory racking of the 6600 series switches the AB469A and 464794-B21 are required. One shelf is required for
every 10 Switches. Exceptions may apply if switches are stacked on top of server or storage devices.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 12
QuickSpecs
HP 6600 Switch Series
Technical Specifications
HP 6600-24G-4XG Switch Ports
(J9264A)
Power supplies
Fan tray
Physical characteristics
Memory and processor
Mounting
Performance
Environment
20 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Media Type: Auto-MDIX;
Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
4 dual-personality ports
each port can be used as either an RJ-45 10/100/1000 port (IEEE 802.3 Type
10BASE-T; IEEE 802.3u Type 100BASE-TX; IEEE 802.3ab 1000BASE-T Gigabit
Ethernet) or an open mini-GBIC slot (for use with mini-GBIC transceivers)
4 SFP+ 10-GbE ports; Duplex: full only
1 RS-232C DB-9 console port
2 power supply slots
includes: 1 x J9269A (HP 6600 Switch Power Supply)
includes: 1 x J9271A
1 fan tray slot
Fan tray supports N+N fans for added redundancy.
Dimensions
17.42(w) x 21.5(d) x 1.7(h) in (44.25 x 54.61 x 4.32
cm) (1U height)
Weight
17.2 lb (7.8 kg)
Freescale PowerPC 8540 @ 666 MHz, 4 MB flash, 256 MB compact flash, 256
MB DDR SDRAM; packet buffer size: 36 MB QDR SDRAM total (18 MB for 1
GbE/10 GbE ports)
Includes hardware for 2-post telco rack or equipment cabinet; horizontal
surface mounting only. The 6600 Series Rack Kit (J9469A) is required for
mounting in 4-post server/networking rack.
1000 Mb Latency
< 3.4 µs (FIFO 64-byte packets)
10 Gbps Latency
< 2.4 µs (FIFO 64-byte packets)
Throughput
up to 75.7 million pps (64-byte packets)
Routing/Switching
capacity
101.8 Gbps
Switch fabric speed
105.6 Gbps
Routing table size
10000 entries
MAC address table size
64000 entries
Operating temperature
41°F to 104°F (5°C to 40°C)
Operating relative
humidity
15% to 80% @ 104°F (40°C), noncondensing
Nonoperating/Storage
temperature
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
relative humidity
15% to 90% @ 149°F (65°C), noncondensing
Alitude
up to 10,000 ft (3 km)
Acoustic
Power: 68 dB, Pressure: 59.5 dB ISO 7779, ISO
9296
Electrical characteristics Achieved Miercom Certified Green Award
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 13
QuickSpecs
HP 6600 Switch Series
Technical Specifications
* Products within this series have achieved sufficient scores in each of the
rated criteria to achieve the Miercom Certified Green distinction Award. See
the Specifications section of this series for more information.
Description
The switch automatically adjusts to any voltage
between 100-120 and 200-240 V with either 50 or
60 Hz.
Maximum heat
697 BTU/hr (735.33 kJ/hr)
dissipation
Voltage
100-120/200-240 VAC
Idle power
167.6 W
Maximum power rating
204.3 W
Frequency
50/60 Hz
Notes
Safety
Idle power is the actual power consumption of the
device with no ports connected.
Maximum power rating and maximum heat
dissipation are the worst-case theoretical
maximum numbers provided for planning the
infrastructure with fully loaded PoE (if equipped),
100% traffic, all ports plugged in, and all modules
populated.
CSA 22.2 No. 60950; EN 60950/IEC 60950; UL 60950
Emissions
FCC Class A; VCCI Class A; EN 55022/CISPR 22 Class A
Immunity
EN
EN 55024, CISPR 24
ESD
IEC 61000-4-2
Radiated
IEC 61000-4-3
EFT/Burst
IEC 61000-4-4
Surge
IEC 61000-4-5
Conducted
IEC 61000-4-6
Power frequency
magnetic field
IEC 61000-4-8
Voltage dips and
interruptions
IEC 61000-4-11
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
Management
Notes
Services
HP PCM+; HP PCM (included); command-line interface; Web browser;
configuration menu
Supported 1G SFP transceivers are revision "B" or later (product number ends
with the letter "B" or later, for example, J9142B, J8177C).
3-year, 4-hour onsite, 13x5 coverage for hardware (U2855E)
3-year, 4-hour onsite, 24x7 coverage for hardware (U2856E)
3-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 SW phone support
and SW updates (U6304E)
3-year, 24x7 SW phone support, software updates (UE262E)
1-year, post-warranty, 4-hour onsite, 13x5 coverage for hardware (HR889E)
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 14
QuickSpecs
HP 6600 Switch Series
Technical Specifications
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware (HR890E)
1-year, post-warranty, 4-hour onsite, 24x7 coverage for hardware, 24x7
software phone support (HR891E)
Installation with minimum configuration, system-based pricing (U4826E)
Installation with HP-provided configuration, system-based pricing (U4830E)
4-year, 4-hour onsite, 13x5 coverage for hardware (UR868E)
4-year, 4-hour onsite, 24x7 coverage for hardware (UR869E)
4-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
(UR870E)
4-year, 24x7 SW phone support, software updates (UR871E)
5-year, 4-hour onsite, 13x5 coverage for hardware (UR872E)
5-year, 4-hour onsite, 24x7 coverage for hardware (UR873E)
5-year, 4-hour onsite, 24x7 coverage for hardware, 24x7 software phone
(UR874E)
5-year, 24x7 SW phone support, software updates (UR875E)
3 Yr 6 hr Call-to-Repair Onsite (UW356E)
4 Yr 6 hr Call-to-Repair Onsite (UW357E)
5 Yr 6 hr Call-to-Repair Onsite (UW358E)
1-year, 6 hour Call-To-Repair Onsite for hardware (HR893E)
1-year, 24x7 software phone support, software updates (HR892E)
1-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS610E)
1-year, 24x7 software phone support, software updates + 4 hour hardware
exchange (HS611E)
3-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS612E)
3-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS613E)
4-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS614E)
4-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS615E)
5-year, 24x7 software phone support, software updates + Next Business Day
Hardware Exchange (HS616E)
5-year, 24x7 software phone support, software updates + 4 hour Hardware
Exchange (HS617E)
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Standards and protocols
(applies to all products in
series)
BGP
RFC 1997 BGP Communities Attribute
RFC 2918 Route Refresh Capability
RFC 4271 A Border Gateway Protocol 4 (BGP-4)
RFC 4456 BGP Route Reflection: An Alternative to
Full Mesh Internal BGP (IBGP)
RFC 5492 Capabilities Advertisement with BGP-4
Device management
RFC 4213 Basic Transition Mechanisms for IPv6
Hosts and Routers
RFC 4251 SSHv6 Architecture
RFC 4252 SSHv6 Authentication
RFC 4253 SSHv6 Transport Layer
RFC 4254 SSHv6 Connection
RFC 4291 IP Version 6 Addressing Architecture
RFC 4293 MIB for IP
RFC 4294 IPv6 Node Requirements
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 15
QuickSpecs
HP 6600 Switch Series
Technical Specifications
RFC 1591 DNS (client)
HTML and telnet management
General protocols
IEEE 802.1ad Q-in-Q
IEEE 802.1AX-2008 Link Aggregation
IEEE 802.1D MAC Bridges
IEEE 802.1p Priority
IEEE 802.1Q VLANs
IEEE 802.1s Multiple Spanning Trees
IEEE 802.1v VLAN classification by Protocol and
Port
IEEE 802.1w Rapid Reconfiguration of Spanning
Tree
IEEE 802.3ad Link Aggregation Control Protocol
(LACP)
IEEE 802.3x Flow Control
RFC 768 UDP
RFC 783 TFTP Protocol (revision 2)
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 868 Time Protocol
RFC 951 BOOTP
RFC 1058 RIPv1
RFC 1350 TFTP Protocol (revision 2)
RFC 1519 CIDR
RFC 1542 BOOTP Extensions
RFC 2030 Simple Network Time Protocol (SNTP) v4
RFC 2131 DHCP
RFC 2453 RIPv2
RFC 2548 (MS-RAS-Vendor only)
RFC 3046 DHCP Relay Agent Information Option
RFC 3576 Ext to RADIUS (CoA only)
RFC 3768 VRRP
RFC 4675 RADIUS VLAN & Priority
UDLD (Uni-directional Link Detection)
IP multicast
RFC 3376 IGMPv3 (host joins only)
RFC 3973 PIM Dense Mode
RFC 4601 PIM Sparse Mode
IPv6
RFC 1981 IPv6 Path MTU Discovery
RFC 2375 IPv6 Multicast Address Assignments
RFC 2460 IPv6 Specification
RFC 2464 Transmission of IPv6 over Ethernet
Networks
RFC 2710 Multicast Listener Discovery (MLD) for
RFC 4419 Key Exchange for SSH
RFC 4443 ICMPv6
RFC 4541 IGMP & MLD Snooping Switch
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address Auto-configuration
RFC 5095 Deprecation of Type 0 Routing Headers
in IPv6
RFC 5340 OSPFv3 for IPv6
RFC 5453 Reserved IPv6 Interface Identifiers
RFC 5519 Multicast Group Membership Discovery
MIB (MLDv2 only)
RFC 5722 Handling of Overlapping IPv6 Fragments
MIBs
IEEE 802.1ap (MSTP and STP MIB's only)
RFC 1213 MIB II
RFC 1493 Bridge MIB
RFC 1724 RIPv2 MIB
RFC 1850 OSPFv2 MIB
RFC 2021 RMONv2 MIB
RFC 2096 IP Forwarding Table MIB
RFC 2613 SMON MIB
RFC 2618 RADIUS Client MIB
RFC 2620 RADIUS Accounting MIB
RFC 2665 Ethernet-Like-MIB
RFC 2668 802.3 MAU MIB
RFC 2674 802.1p and IEEE 802.1Q Bridge MIB
RFC 2737 Entity MIB (Version 2)
RFC 2787 VRRP MIB
RFC 2863 The Interfaces Group MIB
RFC 2925 Ping MIB
RFC 2933 IGMP MIB
Network management
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
RFC 2819 Four groups of RMON: 1 (statistics), 2
(history), 3 (alarm) and 9 (events)
RFC 3176 sFlow
ANSI/TIA-1057 LLDP Media Endpoint Discovery
(LLDP-MED)
SNMPv1/v2c/v3
XRMON
OSPF
RFC 2328 OSPFv2
RFC 3101 OSPF NSSA
RFC 5340 OSPFv3 for IPv6
QoS/CoS
RFC 2474 DiffServ Precedence, including 8
queues/port
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 16
QuickSpecs
HP 6600 Switch Series
Technical Specifications
IPv6
RFC 2925 Definitions of Managed Objects for
Remote Ping, Traceroute, and Lookup Operations
(Ping only)
RFC 3019 MLDv1 MIB
RFC 3315 DHCPv6 (client and relay)
RFC 3484 Default Address Selection for IPv6
RFC 3587 IPv6 Global Unicast Address Format
RFC 3596 DNS Extension for IPv6
RFC 3810 MLDv2 for IPv6
RFC 4022 MIB for TCP
RFC 4087 IP Tunnel MIB
RFC 4113 MIB for UDP
RFC 2597 DiffServ Assured Forwarding (AF)
RFC 2598 DiffServ Expedited Forwarding (EF)
Security
IEEE 802.1X Port Based Network Access Control
RFC 1492 TACACS+
RFC 2865 RADIUS (client only)
RFC 2866 RADIUS Accounting
RFC 3579 RADIUS Support For Extensible
Authentication Protocol (EAP)
Secure Sockets Layer (SSL)
SSHv2 Secure Shell
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 17
QuickSpecs
HP 6600 Switch Series
Accessories
HP 6600 Switch Series
accessories
Modules
HP 6600 Switch Fan Tray
Transceivers
HP X111 100M SFP LC FX Transceiver
HP X112 100M SFP LC BX-D Transceiver
HP X112 100M SFP LC BX-U Transceiver
HP X132 10G SFP+ LC SR Transceiver
HP X132 10G SFP+ LC LR Transceiver
HP X132 10G SFP+ LC LRM Transceiver
HP X121 1G SFP LC LH Transceiver
HP X121 1G SFP LC SX Transceiver
HP X121 1G SFP LC LX Transceiver
HP X122 1G SFP LC BX-D Transceiver
HP X122 1G SFP LC BX-U Transceiver
HP X132 10G SFP+ LC ER Transceiver
Cables
HP X242 10G SFP+ to SFP+ 1m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HP X242 10G SFP+ to SFP+ 7m Direct Attach Copper Cable
HP X244 10G XFP to SFP+ 1m Direct Attach Copper Cable
HP X244 10G XFP to SFP+ 3m Direct Attach Copper Cable
HP X244 10G XFP to SFP+ 5m Direct Attach Copper Cable
HP 0.5 m Multimode OM3 LC/LC Optical Cable
HP 1 m Multimode OM3 LC/LC Optical Cable
HP 2 m Multimode OM3 LC/LC Optical Cable
HP 5 m Multimode OM3 LC/LC Optical Cable
HP 15 m Multimode OM3 LC/LC Optical Cable
HP 30 m Multimode OM3 LC/LC Optical Cable
HP 50 m Multimode OM3 LC/LC Optical Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 1m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 2m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 5m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 15m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 30m Cable
HP Premier Flex LC/LC Multi-mode OM4 2 fiber 50m Cable
HP BLc SFP+ 0.5m 10GbE Copper Cable
HP BLc SFP+ 1m 10GbE Copper Cable
HP BLc SFP+ 3m 10GbE Copper Cable
HP BLc SFP+ 5m 10GbE Copper Cable
HP BLc SFP+ 7m 10GbE Copper Cable
HP X242 SFP+ to SFP+ 10m Direct Attach Copper Cable
HP X242 SFP+ to SFP+ 15m Direct Attach Copper Cable
Power Supply
HP 6600 Switch Power Supply
DA - 13267 EMEA — Version 20 — February 4, 2014
J9271A
J9054C
J9099B
J9100B
J9150A
J9151A
J9152A
J4860C
J4858C
J4859C
J9142B
J9143B
J9153A
J9281B
J9283B
J9285B
J9300A
J9301A
J9302A
AJ833A
AJ834A
AJ835A
AJ836A
AJ837A
AJ838A
AJ839A
QK732A
QK733A
QK734A
QK735A
QK736A
QK737A
487649-B21
487652-B21
487655-B21
537963-B21
487658-B21
J9286B
J9287B
J9269A
Page 18
QuickSpecs
HP 6600 Switch Series
Accessories
Mounting Kit
HP 6600 Series Switch Rack Kit
HP 6600-24XG, 48G and 48G-4XG Switch Air Plenum Kit
HP 6600-24G and 24G-4XG Switch Air Plenum Kit
License
HP 6600 Switch Premium License
DA - 13267 EMEA — Version 20 — February 4, 2014
J9469A
J9480A
J9481A
J9305A
Page 19
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
NOTE: Details are not available for all accessories. The following specifications were available at the time of publication.
HP 6600 Switch Fan Tray
(J9271A)
Physical characteristics
Dimensions
Services
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
HP X111 100M SFP LC FX
Transceiver (J9054C)
Ports
1 LC 100BASE-FX port (IEEE 802.3u Type 100BASE-FX); Duplex: half or full
Physical characteristics
Dimensions
Environment
Cabling
Notes
Services
5(d) x 5(w) x 5(h) in. (12.7 x 12.7 x 12.7 cm)
Weight
2.7(d) x 0.54(w) x 0.48(h) in. (6.86 x 1.38 x 1.22
cm)
0.06 lb. (0.03 kg)
Operating temperature
32°F to 158°F (0°C to 70°C)
Operating relative
humidity
5% to 95%
Nonoperating/Storage
temperature
-40°F to 185°F (-40°C to 85°C)
Nonoperating/Storage
relative humidity
5% to 85%
Altitude
up to 10,000 ft. (3 km)
Cable type:
62.5/125 ìm or 50/125 ìm (core/cladding) diameter, graded-index, low metal
content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2
Type A1b or A1a, respectively;
Maximum distance:
• 2 km (full duplex) or 412 m (half duplex)
Transmitter wavelength: 1310nm
Power consumption is 1.1 watt maximum.
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the J9054B 100-FX SFP-LC
Transceiver" on the "ProCurve Mini-GBICs and SFPs" Manuals Web page.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 20
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP X112 100M SFP LC BX-D Ports
Transceiver (J9099B)
Physical characteristics
A small form-factor
pluggable (SFP) 100Megabit BX (bi-directional)
"downstream" transceiver Environment
that provides 100 Mbps
full-duplex connectivity up
to 10 km on one strand of
singlemode fiber. The
J9099B connects to the
Cabling
J9100B "upstream"
transceiver, or to any IEEEstandard 100BASE-BX10-U
("upstream") device.
1 LC 100BASE-BX10 port (IEEE 802.3ah Type 100BASE-BX10-D); Duplex: full
only
Dimensions
2.7(d) x 0.55(w) x 0.48(h) in. (6.86 x 1.39 x 1.22
cm)
Weight
0.04 lb. (0.03 kg)
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
0% to 95%, noncondensing
Nonoperating/Storage
temperature
-40ºF to 185ºF (-40ºC to 85ºC)
Type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
0.5-10,000 m (single-mode fiber)
Transmit wavelength: 1550 nm. Receive wavelength: 1310 nm.
Power consumption is 1.1 watt maximum.
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the HP BX Transceivers" on the
"HP Mini-GBICs and SFPs" Manuals Web page.
The J9099B connects to the J9100B "upstream" transceiver, or to any IEEEstandard 100BASE-BX10-U ("upstream") device. (A 100-BX-D transceiver can
only connect to a 100-BX-U product. You cannot connect two 100-BX-D
transceivers together.)
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Notes
Services
HP X112 100M SFP LC BX-U Ports
Transceiver (J9100B)
Physical characteristics
A small form-factor
pluggable (SFP) 100Megabit BX (bi-directional)
Environment
"upstream" transceiver
that provides 100 Mbps
full-duplex connectivity up
to 10 km on one strand of
singlemode fiber. The
J9100B connects to the
Cabling
J9099B "downstream"
transceiver, or to any IEEEstandard 100BASE-BX10-D
("downstream")
device.
1 LC 100BASE-BX10 port (IEEE 802.3ah Type 100BASE-BX10-U); Duplex: full
only
Dimensions
2.7(d) x 0.55(w) x 0.48(h) in. (6.86 x 1.39 x 1.22
cm)
Weight
0.07 lb. (.03 kg)
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
0% to 95%, noncondensing
Nonoperating/Storage
temperature
-40ºF to 185ºF (-40ºC to 85ºC)
Type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 21
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
0.5-10,000 m (single-mode fiber)
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the HP BX Transceivers" on the
"HP Mini-GBICs and SFPs" Manuals Web page.
The J9100B connects to the J9099B "downstream" transceiver, or to any IEEEstandard 100BASE-BX10- D ("downstream") device. (A 100-BX-U transceiver
can only connect to a 100-BX-D product. You cannot connect two 100-BX-U
transceivers together.)
Transmit wavelength: 1310 nm. Receive wavelength: 1550 nm.
Power consumption is 1.1 watts maximum.
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Notes
Services
HP X132 10G SFP+ LC SR
Transceiver (J9150A)
Ports
1 LC 10-GbE port (IEEE 802.3ae Type 10Gbase-SR); Duplex: full only
Connectivity
Connector type
LC
Wavelength
850 nm
Dimensions
Weight
2.19(d) x 0.54(w) x 0.47(h) in. (5.57 x 1.38 x 1.19
cm)
0.04 lb. (0.02 kg)
Transceiver form factor
SFP+
Operating temperature
32°F to 158°F (0°C to 70°C)
Operating relative
humidity
0% to 85%, noncondensing
Nonoperating/Storage
temperature
-40°F to 185°F (-40°C to 85°C)
Altitude
up to 10,000 ft. (3 km)
A 10-Gigabit transceiver in
Physical characteristics
SFP+ form-factor that
supports the 10-Gigabit SR
standard, providing 10Gigabit connectivity up to
300 m on multimode fiber.
Environment
Electrical characteristics Power consumption
typical
0.6 W
Power consumption
maximum
0.8 W
Cabling
Cable type:
62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low metal
content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2
Type A1b or A1a, respectively;
Maximum distance:
2-26m with 62.5 µm multimode cable @ 160 MHz*km
2-33m with 62.5 µm multimode cable @ 200 MHz*km
2-66m with 50 µm multimode cable @ 400 MHz*km
2-82m with 50 µm multimode cable @ 500 MHz*km
2-300m with 50 µm multimode cable @ 2000 MHz*km
Cable length
2-300m
Fiber type
Multi Mode
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 22
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
Notes
HP X132 10G SFP+ LC LR
Transceiver (J9151A)
Services
For fiber patch cords, use Ultra Physical Contact (UPC) surface
termination/polish. Angled Physical Contact (APC) is not recommended.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Ports
1 LC 10-GbE port (IEEE 802.3ae Type 10Gbase-LR); Duplex: full only
Connectivity
Connector type
LC
Wavelength
1310 nm
Dimensions
Weight
2.19(d) x 0.54(w) x 0.47(h) in. (5.57 x 1.38 x 1.19
cm)
0.04 lb. (.02 kg)
Transceiver form factor
SFP+
Operating temperature
32°F to 158°F (0°C to 70°C)
Operating relative
humidity
0% to 85%, noncondensing
Nonoperating/Storage
temperature
-40°F to 185°F (-40°C to 85°C)
Altitude
up to 10,000 ft. (3 km)
A 10-Gigabit transceiver in
Physical characteristics
SFP+ form-factor that
supports the 10-Gigabit LR
standard, providing 10Gigabit connectivity up to
10 km on single-mode
Environment
fiber.
Electrical characteristics Power consumption
typical
Power consumption
maximum
Cabling
0.9 W
1W
Cable type:
Low metal content, single-mode fiber-optic, complying with ITU-T G.652 and
ISO/IEC 793-2 Type B1;
Maximum distance:
2m-10km with 9/125 µm single-mode cable
Cable length
2m to 10km
Fiber type
Notes
Services
Single Mode
Conditioning patch cord cables are not supported.
For fiber patch cords, use Ultra Physical Contact (UPC) surface
termination/polish. Angled Physical Contact (APC) is not recommended.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 23
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP X132 10G SFP+ LC LRM Ports
Transceiver (J9152A)
Connectivity
1 LC 10-GbE port (IEEE 802.3aq Type 10Gbase-LRM); Duplex: full only
Connector type
LC
A 10-Gigabit transceiver in
Physical characteristics
SFP+ form-factor that
supports the 10-Gigabit
LRM standard, for 10Gigabit connectivity up to
220 m on legacy
Environment
multimode fiber.
Wavelength
1310 nm
Dimensions
Weight
2.19(d) x 0.54(w) x 0.47(h) in. (5.57 x 1.38 x 1.19
cm)
0.04 lb. (.02 kg)
Transceiver form factor
SFP+
Operating temperature
32°F to 158°F (0°C to 70°C)
Operating relative
humidity
0% to 85%, noncondensing
Nonoperating/Storage
temperature
-40°F to 185°F (-40°C to 85°C)
Altitude
up to 10,000 ft. (3 km)
Electrical characteristics Power consumption
typical
Power consumption
maximum
Cabling
0.7 W
1W
Cable type:
62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low metal
content, multimode fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2
Type A1b or A1a, respectively (a mode conditioning patch cord may be needed
in some multimode fiber installations);
Maximum distance:
0.5-220m with 62.5 µm multimode cable @ 160/500 MHz*km
0.5-220m with 62.5 µm multimode cable @ 200/500 MHz*km
0.5-100m with 50 µm multimode cable @ 400/400 MHz*km
0.5-220m with 50 µm multimode cable @ 500/500 MHz*km
0.5-220m with 50 µm multimode cable @ 1500/500 MHz*km
Cable length
0.5m to 220m
Fiber type
Notes
Services
Multi Mode
For OM3 cable (50 µm multimode @ 1500/500 MHz*km), a mode-conditioning
patch cord is not required. Other multimode cables may require modeconditioning patch cords to achieve the maximum distances listed above.
For fiber patch cords, use Ultra Physical Contact (UPC) surface
termination/polish. Angled Physical Contact (APC) is not recommended.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 24
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP X121 1G SFP LC LH
Transceiver (J4860C)
Ports
Physical characteristics
A small form-factor
pluggable (SFP) Gigabit LH Environment
transceiver that provides a
full-duplex Gigabit solution
up to 70 km on singlemode fiber.
Cabling
1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm optics); Duplex:
full only
Dimensions: 2.17(d) x 0.60(w) x 0.46(h) in. (5.5 x 1.53 x 1.18 cm)
Weight: 0.04 lb. (0.02 kg)
Operating temperature: -40°F to 185°F (-40°C to 85°C)
Operating relative humidity: 0% to 95% @ 77°F (25°C), noncondensing
Nonoperating/Storage temperature: -40°F to 185°F (-40°C to 85°C)
Altitude: up to 10,000 ft. (3 km)
Cable type:
Low metal content, single-mode fiber-optic, complying with ITU-T
G.652 and ISO/IEC 793-2 Type B1;
Maximum distance:
10-70,000 m (single-mode fiber)
Power consumption is 0.8 watts typical with 1 watt maximum at 100%
utilization.
For distances less than 20 km, a 10 dB attenuator must be used.
For distances between 20 km and 40 km, a 5 dB attenuator must be used.
Attenuators can be purchased from most cable vendors.
Refer to the HP website at www.hp.com/networking/services for details on the
service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local HP sales office.
Notes
Services
HP X121 1G SFP LC SX
Transceiver (J4858C)
A small form-factor
pluggable (SFP) Gigabit SX
transceiver that provides a
full-duplex Gigabit solution
up to 550 m on multimode
fiber.
Ports
Physical characteristics
1 LC 1000BASE-SX port; Duplex: full only
Dimensions: 2.24(d) x 0.54(w) x 0.48(h) in. (5.69 x 1.37 x 1.22 cm)
Weight: 0.04 lb. (0.02 kg)
Transceiver form factor: SFP
Environment
Operating temperature: 32°F to 158°F (0°C to 70°C)
Operating relative humidity: 5% to 85%, noncondensing
Nonoperating/Storage temperature: -40°F to 203°F (-40°C to 85°C)
Altitude: up to 10,000 ft. (3 km)
Electrical characteristics Power consumption typical: 0.4 W
Power consumption maximum: 0.7 W
Cabling
Type:
62.5/125 µm or 50/125 µm (core/cladding) diameter, graded-index, low
metal content, multimode fiber optic, complying with ITU-T G.651 and
ISO/IEC 793-2 Type A1b or A1a, respectively;
Maximum distance:
2-220 m (62.5 µm core diameter, 160 MHz*km bandwidth
2-275 m (62.5 µm core diameter, 200 MHz*km bandwidth
2-500 m (50 µm core diameter, 400 MHz*km bandwidth)
2-550 m (50 µm core diameter, 500 MHz*km bandwidth)
Cable length: 2-550m
Fiber type: Multi Mode
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 25
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP X121 1G SFP LC LX
Transceiver (J4859C)
Services
Refer to the HP website at www.hp.com/networking/services for details on the
service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local HP sales office.
Ports
Physical characteristics
1 LC 1000BASE-LX port (IEEE 802.3z Type 1000BASE-LX); Duplex: full only
Dimensions: 2.24(d) x 0.54(w) x 0.486(h) in. (5.69 x 1.37 x 1.23 cm)
Weight:0.04 lb. (0.02 kg)
Operating temperature: 32°F to 158°F (0°C to 70°C)
Operating relative humidity: 0% to 85%, noncondensing
Nonoperating/Storage temperature: -40°F to 212°F (-40°C to 100°C)
Altitude: up to 10,000 ft. (3 km)
Type:
HP X121 1G SFP LC LX
Environment
Transceiver: An SFP format
gigabit transceiver with LC
connectors using LX
technology.
Cabling
Either single mode or multimode; 62.5/125 µm or 50/125 µm
(core/cladding) diameter, graded-index, low metal content, multimode
fiber optic, complying with ITU-T G.651 and ISO/IEC 793-2 Type A1b or
A1a, respectively; Low metal content, single-mode fiber-optic,
complying with ITU-T G.652 and ISO/IEC 793-2 Type B1;
Maximum distance:
Notes
Services
2-550 m (multimode 62.5 µm core diameter, 500 MHz*km bandwidth)
2-550 m (multimode 50 µm core diameter, 400 MHz*km bandwidth)
2-550 m (multimode 50 µm core diameter, 500 MHz*km bandwidth)
2-10,000 m (single-mode fiber)
A mode conditioning patch cord may be needed in some multimode fiber
installations.
Wavelength: 1310nm
Power Consumption: < 500mW Typical
Refer to the HP website at www.hp.com/networking/services for details on the
service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local HP sales office.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 26
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP X122 1G SFP LC BX-D
Transceiver (J9142B)
Ports
Physical characteristics
A small form-factor
pluggable (SFP) Gigabit-BX
(bi-directional)
"downstream" transceiver Environment
that provides a full-duplex
Gigabit solution up to 10
km on one strand of
single-mode fiber. The
J9142B connects to the
Cabling
J9143B "upstream"
transceiver, or to any IEEEstandard 1000BASE-BX10U ("upstream") device.
Services
Ports
Physical characteristics
A small form-factor
pluggable (SFP) Gigabit-BX
(bi-directional) "upstream"
transceiver that provides a Environment
full-duplex Gigabit solution
up to 10 km on one strand
of single-mode fiber. The
J9143B connects to the
J9142B "downstream"
transceiver, or to any IEEE- Cabling
standard 1000BASE-BX10D ("downstream")
device.
Notes
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
0% to 95%, non-condensing
Non-operating/
Storage temperature
–40ºF to 185ºF –40ºC to 85ºC)
Type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
0.5-10,000 m (single-mode fiber)
Transmit wavelength: 1490 nm. Receive wavelength: 1310 nm.
Power consumption is 1 watt maximum.
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the HP BX Transceivers" on the
"HP Mini-GBICs and SFPs" Manuals Web page.
The J9142B connects to the J9143B "upstream" transceiver, or to any IEEEstandard 1000BASE-BX10-U ("upstream") device. (A 1000-BX-D transceiver
can only connect to a 1000-BX-U product. You cannot connect two 1000-BX-D
transceivers together.)
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Notes
HP X122 1G SFP LC BX-U
Transceiver (J9143B)
1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-D); Duplex:
full only
Dimensions
2.19(d) x 0.54(w) x 0.46(h) in. (5.57 x 1.37 x 1.18
cm)
Weight
0.04 lb. (0.02 kg)
1 LC 1000BASE-BX10 port (IEEE 802.3ah Type 1000BASE-BX10-U); Duplex:
full only
Dimensions
2.19(d) x 0.54(w) x 0.46(h) in. (5.57 x 1.37 x 1.18
cm)
Weight
0.04 lb. (0.02 kg)
Operating temperature
32ºF to 158ºF (0ºC to 70ºC)
Operating relative
humidity
0% to 95%, non-condensing
Non-operating/
Storage temperature
–40ºF to 185ºF –40ºC to 85ºC)
Type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
0.5-10,000 m (single-mode fiber)
Transmit wavelength: 1310 nm. Receive wavelength: 1490 nm.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 27
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
For supported platforms and minimum software requirements to support this
product, see the document titled "Support for the HP BX Transceivers" on the
"HP Mini-GBICs and SFPs" Manuals Web page.
The J9143B connects to the J9142B "downstream" transceiver, or to any IEEEstandard 1000BASE-BX10-D ("downstream") device. (A 1000-BX-U
transceiver can only connect to a 1000-BX-D product. You cannot connect two
1000-BX-U transceivers together.)
Power consumption is 1 watt maximum.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Services
HP X132 10G SFP+ LC ER
Transceiver (J9153A)
Ports
1 LC 10-GbE port (IEEE 802.3ae Type 10Gbase-ER); Duplex: full only
Connectivity
Connector type
LC
Wavelength
1550 nm
Dimensions
Weight
2.22(d) x 0.55(w) x 0.47(h) in. (5.65 x 1.39 x 1.19
cm)
.04 lb., Fully loaded
Transceiver form factor
SFP+
Operating temperature
32°F to 158°F (0°C to 70°C)
Operating relative
humidity
5% to 95%, noncondensing
Nonoperating/Storage
temperature
-40°F to 185°F (-40°C to 85°C)
Nonoperating/Storage
relative humidity
5% to 95%, noncondensing
Altitude
up to 10,000 ft. (3 km)
The SFP+ ER Transceiver
will transmit 10Gbps over Physical characteristics
up to 40km using standard
OM3 fiber cable. This
product expands the HP
Networking transceiver
portfolio for connections Environment
from 0m to 40km. Use only
genuine HP transceivers
with your HP Networking
equipment to ensure
reliability and support.
Electrical characteristics Power consumption
typical
1.3 W
Power consumption
maximum
1.5 W
Cabling
Cable type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
40km
Fiber type
Notes
Services
Single Mode
Check switch release notes for minimum version of software required to
support this transceiver.
Some switches have limits as to how many of this particular transceiver can
be installed. See the release notes of the switch software/firmware being
used for more details.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 28
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP X242 SFP+ SFP+ 1 m
Direct Attach Cable
(J9281B)
Connectivity
Length
3.28 ft. (1 m)
Physical characteristics
Weight
0.24 lb. (0.11 kg) the cable with an SFP+
transceiver at each end of the cable
32ºF to 158ºF (0ºC to 70ºC)
5% to 95%, noncondensing
Environment
Operating temperature
Operating relative
humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Altitude
Electrical characteristics Notes
Notes
5% to 95%, noncondensing
up to 10,000 ft. (3 km)
0.04 watts maximum per transceiver end
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Services
HP X242 SFP+ SFP+ 3 m
Direct Attach Cable
(J9283B)
14ºF to 185ºF (-10ºC to 85ºC)
Connectivity
Length
10 ft. (3 m)
Physical characteristics
Weight
.49 lb. (0.22 kg), Fully loaded the cable with an
SFP+ transceiver at each end of the cable
32ºF to 158ºF (0ºC to 70ºC)
5% to 95%, noncondensing
Environment
Operating temperature
Operating relative
humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Altitude
Electrical characteristics Notes
Notes
14ºF to 185ºF (-10ºC to 85ºC)
5% to 95%, noncondensing
up to 10,000 ft. (3 km)
0.04 watts maximum per transceiver end
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 29
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP X242 SFP+ SFP+ 7 m
Direct Attach Cable
(J9285B)
Services
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Connectivity
Length
22.97 ft. (7 m)
Physical characteristics
Weight
1.02 lb., Fully loaded the cable with an SFP+
transceiver at each end of the cable
32ºF to 158ºF (0ºC to 70ºC)
5% to 95%, noncondensing
Environment
Operating temperature
Operating relative
humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Altitude
Electrical characteristics Notes
Notes
5% to 95%, noncondensing
up to 10,000 ft. (3 km)
0.04 watts maximum per transceiver end
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Services
HP X244 XFP SFP+ 1 m
Direct Attach Cable
(J9300A)
14ºF to 185ºF (-10ºC to 85ºC)
Connectivity
Length
3.28 ft. (1 m)
Physical characteristics
Weight
.27 lb. (0.12 kg), Fully loaded cable with XFP
transcevier on one end and SFP+ on the other end
32ºF to 158ºF (0ºC to 70ºC)
5% to 95%, noncondensing
Environment
A 1m direct attach copper
cable with an XFP
connector attached on one
end and an SFP+ connector
attached on the other end.
This cable
provides a low price
connectivity option
between switches/servers/
Notes
storage to interconnect
XFP and SFP+ form factors. Services
Operating temperature
Operating relative
humidity
Nonoperating/Storage
32ºF to 158ºF (0ºC to 70ºC)
temperature
Nonoperating/Storage
5% to 95%, noncondensing
relative humidity
Altitude
up to 10,000 ft. (3 km)
XFP end consumes 2 watts SFP+ end consumes 0.036 watts
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 30
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP X244 XFP SFP+ 3 m
Direct Attach Cable
(J9301A)
Connectivity
Length
9.84 ft. (3 m)
Physical characteristics
Weight
.51 lb. (0.23 kg), Fully loaded cable with XFP
transcevier on one end and SFP+ on the other end
32ºF to 158ºF (0ºC to 70ºC)
5% to 95%, noncondensing
Environment
A 3m direct attach copper
cable with an XFP
connector attached on one
end and an SFP+ connector
attached on the other end.
This cable provides a low
price connectivity option
between switches/servers/
storage to interconnect
XFP and SFP+ form factors. Cabling
Notes
HP X244 XFP SFP+ 5 m
Direct Attach Cable
(J9302A)
Operating temperature
Operating relative
humidity
Nonoperating/Storage
32ºF to 158ºF (0ºC to 70ºC)
temperature
Nonoperating/Storage
5% to 95%, noncondensing
relative humidity
Altitude
up to 10,000 ft. (3 km)
Maximum distance:
• 3m Direct Attach Cable
XFP end consumes 2 watts SFP+ end consumes 0.036 watts
Services
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Connectivity
Length
16.4 ft. (5 m)
Physical characteristics
Weight
.74 lb. (0.34 kg), Fully loaded cable with XFP
transcevier on one end and SFP+ on the other end
32ºF to 158ºF (0ºC to 70ºC)
5% to 95%, noncondensing
Environment
A 5m direct attach copper
cable with an XFP
connector attached on one
end and an SFP+ connector
attached on the other end.
This cable provides a low
price connectivity option
between switches/servers/
storage to interconnect
XFP and SFP+ form factors. Notes
Services
Operating temperature
Operating relative
humidity
Nonoperating/Storage
32ºF to 158ºF (0ºC to 70ºC)
temperature
Nonoperating/Storage
5% to 95%, noncondensing
relative humidity
Altitude
up to 10,000 ft. (3 km)
XFP end consumes 2 watts SFP+ end conumes 0.036 watts
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 31
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP 0.5 m Multimode OM3 Cabling
LC/LC Optical Cable
(AJ833A)
Notes
Services
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical glass: Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical glass: Bandwidth: For Laser sources: 2000/500 MHz-km
@850/1300nm. VCSEL Laser sources: 600 / 600 meters @850/1300nm
for Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber and designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 32
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP 1 m Multimode OM3
LC/LC Optical Cable
(AJ834A)
Cabling
Notes
Services
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 33
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP 2 m Multimode OM3
LC/LC Optical Cable
(AJ835A)
Cabling
Notes
Services
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 34
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP 5 m Multimode OM3
LC/LC Optical Cable
(AJ836A)
Cabling
Notes
Services
Cable type:
50/125 µm core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: This specification defines the detail requirements for a tight
buffered duplex fiber optic multimode OM3 50/125 um fiber optic cable and
Ethernet assembly with LC duplex connectors on one end and LC duplex
connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 35
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP 15 m Multimode OM3
LC/LC Optical Cable
(AJ837A)
Cabling
Notes
Services
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 36
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP 30 m Multimode OM3
LC/LC Optical Cable
(AJ838A)
Cabling
Notes
Services
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 37
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP 50 m Multimode OM3
LC/LC Optical Cable
(AJ839A)
Cabling
Notes
Services
Cable type:
50/125 µm (core/cladding) diameter, mulitimode fiber optic, with effective
modal bandwidth of 2000 MHz/km as detailed in TIA-492AAAC for distances of
up to 300 m;
Maximum distance:
10Gbps Transfer Rate (Ethernet): 300m
Cable Specs: Tight buffered duplex fiber optic multimode OM3 50/125 um
fiber optic cable and Ethernet assembly with LC duplex connectors on one end
and LC duplex connectors on other end.
Dimensions: Core diameter: 50 ± 3.0um Cladding diameter: 125 ± 2.0um
Coating diameter: 245 ± 10um
Optical Glass Bandwidth: For LED sources: 1500/500 MHz-km
@850/1300nm.
Optical Glass: For Laser sources: 2000/500 MHz-km @850/1300nm.
VCSEL Laser sources: Shall achieve 600 / 600 meters @850/1300nm for
Gigabit Ethernet compliant links.
CABLE: The cable is duplex zipcord graded index 50/125um multimode
optical fiber. The cable is designed to work in both the 850 and 1300 nm
wavelength windows.
BULK CABLE & CABLE ASSEMBLY CONFIGURATION:
Jacket Material: Riser Grade - Low Smoke Zero Halogen thermoplastic.
Jacket Color: Aqua for OM3 multimode per TIA 598
Boot Color: White
Insertion Loss: less than 0.5 dB @ 850 with LED source, 0.003 dB/M
added for lengths > 30 meters.
Maximum Cable attenuation: 3.0 dB/km @ 850 nm, 1.0 dB/Km @ 1310
nm @ 23°C as tested in accordance with EIA 455-46.
Weight: Air Packed Weight: 1 LB Net Weight: 0.454Kg
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 38
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP Premier Flex LC/LC
Multi-mode OM4 2 fiber
1m Cable (QK732A)
Notes
Services
HP Premier Flex LC/LC
Multi-mode OM4 2 fiber
2m Cable (QK733A)
Notes
Services
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
• Core Diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 39
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP Premier Flex LC/LC
Multi-mode OM4 2 fiber
5m Cable (QK734A)
Notes
Services
HP Premier Flex LC/LC
Multi-mode OM4 2 fiber
15m Cable (QK735A)
Notes
Services
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 40
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP Premier Flex LC/LC
Multi-mode OM4 2 fiber
30m Cable (QK736A)
Notes
Services
HP Premier Flex LC/LC
Multi-mode OM4 2 fiber
50m Cable (QK737A)
Notes
Services
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+ 50/125um
duplex cable and Ethernet assembly with LC duplex connectors on each end.
• Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
• Bandwidth: 3000 MHz-km @ 850nm (Laser)
• Jacket Color: Blue
• Jacket Material: Riser Grade – Low Smoke Zero Halogen (LSZH) thermoplastic
• Boot Color: White
• Outer Jacket Print: HP PremierFlex OM3+ Fiber Optic Cable, 50/125um, Type
OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also has a longitudinal white
stripe that runs the entire length of the cable.
• Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m added
for lengths >30m
• Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @ 1310nm @
23°C as tested in accordance with EIA 455-45
Refer to the HP website at www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 41
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP BLc SFP+ 0.5m 10GbE
Copper Cable (487649B21)
Connectivity
Length
1.64 ft. (0.5 m)
Physical characteristics
Weight
.18 lb. (0.08 kg) the cable with an SFP+
transceiver at each end of the cable
32°F to 158°F (0°C to 70°C)
5% to 95%, noncondensing
Environment
Operating temperature
Operating relative
humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Altitude
Electrical characteristics Notes
Notes
5% to 95%, noncondensing
up to 10,000 ft. (3 km)
0.04 watts maximum per transceiver end
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Services
HP BLc SFP+ 1m 10GbE
Copper Cable (487652B21)
14°F to 185°F (-10°C to 85°C)
Connectivity
Length
3.28 ft. (1 m)
Physical characteristics
Weight
.24 lb. (0.11 kg) the cable with an SFP+
transceiver at each end of the cable
32°F to 158°F (0°C to 70°C)
5% to 95%, noncondensing
Environment
Operating temperature
Operating relative
humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Altitude
Electrical characteristics Notes
Notes
Services
14°F to 185°F (-10°C to 85°C)
5% to 95%, noncondensing
up to 10,000 ft. (3 km)
0.04 watts maximum per transceiver end
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 42
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP BLc SFP+ 3m 10GbE
Copper Cable (487655B21)
Connectivity
Length
9.84 ft. (3 m)
Physical characteristics
Weight
0.49 lb. (0.22 kg) the cable with an SFP+
transceiver at each end of the cable
32°F to 158°F (0°C to 70°C)
5% to 95%, noncondensing
Environment
Operating temperature
Operating relative
humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Altitude
Electrical characteristics Notes
Notes
5% to 95%, noncondensing
up to 10,000 ft. (3 km)
0.04 watts maximum per transceiver end
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Services
HP BLc SFP+ 5m 10GbE
Copper Cable (537963B21)
14°F to 185°F (-10°C to 85°C)
Connectivity
Length
16.40 ft. (5 m)
Physical characteristics
Weight
0.75 lb. (0.34 kg) the cable with an SFP+
transceiver at each end of the cable
32°F to 158°F (0°C to 70°C)
5% to 95%, noncondensing
Environment
Operating temperature
Operating relative
humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Altitude
Electrical characteristics Notes
Notes
14°F to 185°F (-10°C to 85°C)
5% to 95%, noncondensing
up to 10,000 ft. (3 km)
0.04 watts maximum per transceiver end
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 43
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP BLc SFP+ 7m 10GbE
Copper Cable (487658B21)
Services
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Connectivity
Length
22.96 ft. (7 m)
Physical characteristics
Weight
1.01 lb. (0.46 kg) the cable with an SFP+
transceiver at each end of the cable
32°F to 158°F (0°C to 70°C)
5% to 95%, noncondensing
Environment
Operating temperature
Operating relative
humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Altitude
Electrical characteristics Notes
Notes
5% to 95%, noncondensing
up to 10,000 ft. (3 km)
0.04 watts maximum per transceiver end
Electrical Properties
• Cable Characteristic Impedance: 100 ohms
• Crosstalk between pairs: 2% max
• Time delay: 1.31 nsec/ft
Physical Properties
• Cable Diameter: 0.180"
• Minimum Cable Bend Radius: 1.0"
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Services
HP 6600 Switch Power
Supply (J9269A)
14°F to 185°F (-10°C to 85°C)
Physical characteristics
Environment
Dimensions
9.37(d) x 3.39(w) x 1.5(h) in. (23.8 x 8.6 x 3.8 cm)
Weight
2.45 lb. (1.11 kg)
Operating temperature
41ºF to 104ºF (5ºC to 40ºC)
Operating relative
humidity
15% to 80% @ 104ºF (40ºC), non-condensing
Non-operating/
Storage temperature
-40ºF to 158ºF (-40ºC to 70ºC)
Non-operating/
15% to 90% @ 104ºF (40ºC), non-condensing
Storage relative humidity
Altitude
up to 10,000 ft. (3 km)
Electrical characteristics Notes
Services
Notes: Power draw and heat dissipation are
dependent on the number of power supplies
installed.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 44
QuickSpecs
HP 6600 Switch Series
Accessory Product Details
HP 6600 Series Rack Kit
(J9469A)
Notes
Rack kit can be used to mount any of the E6600 switches (J9263A, J9264A,
J9265A, J9451A, and J9452A) in HP 10K or other 3rd party 4-post racks.
Shipping weight: 5 lbs.
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
Services
HP 6600 Switch Premium Services
License (J9305A)
3-Year, 9x5 SW phone support, software updates (UT479E)
3-year, 24x7 SW phone support, software updates (UT480E)
4-year, 24x7 SW phone support, software updates (UT456E)
5-year, 24x7 SW phone support, software updates (UT457E)
1-year, 24x7 software phone support, software updates (HS531E)
Refer to the HP website at: www.hp.com/networking/services for details on
the service-level descriptions and product numbers. For details about services
and response times in your area, please contact your local HP sales office.
To learn more, visit: www.hp.com/networking
© Copyright 2008-2014 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without
notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products
and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial
errors or omissions contained herein.
Microsoft is a U.S. registered trademark of Microsoft Corporation.
DA - 13267 EMEA — Version 20 — February 4, 2014
Page 45
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021