OFNA 9.5V Violator RC car Instruction manual
Below you will find brief information for 9.5V Violator. The 9.5V Violator is a 1/8 scale off-road buggy that is ready to run right out of the box. It features a powerful .26 engine, a tuned polished dual chamber racing pipe, and a unique adjustable chassis width of 310mm or 330mm. This buggy also comes with many other features, including a full race offset king pin aluminum steering knuckle, three sealed differentials with 6 steel gears, racing X-Equal tires and V-spoke wheels, and adjustable front and rear roll bars. With its high performance and features, the 9.5V Violator is perfect for both beginners and experienced racers.
Advertisement
Advertisement
Strong Front and Rear chassis braces.
Tuned Polished Dual Chamber racing pipe.
INSTRUCTION MANUAL
Unique adjustable chassis width of 310mm or 330mm.
High performance .26 engine with Shaft Start Motor handle.
Full race Offset King Pin aluminum steering knuckle.
Three sealed differentials with 6 steel gears.
Racing X-Equal tires and V-spoke wheels.
Adjustable Front and Rear roll bars.
Multi disc brakes with adjustable bias.
Hard Coated Threaded body oil fill shocks.
5 Degree hard coated 3mm chassis.
Racing 3 shoe clutch with Aluminum CNC flywheel.
Steel main spur gear and center differential.
Adjustable servo saver.
Front CVA joint and 8mm axles.
140+cc fuel tank with inside stone filter.
THINGS NEEDED
RTR KITS - REQUIRED FOR OPERATION
You will need to buy a few items to start the engine and run the car.
• Use 20% nitro CAR fuel. Do not use airplane or heli fuels, they will over heat engine.
• Buy LONG glow plugs, like OFNA/PICCO Plug (#51007 or 51008).
Use plugs without idle bar. Do NOT use plugs, like the MC-59 or OS-8
In your box you will find..
• #10163 - Bottle, spout top
• #10219 - Red “D” size glow heater
Glow Fuel
20%
AA Batteries ( 12 pcs )
You need to get batteries for the radio transmitter and the car receiver packs.
• Radio TX needs (8) eight AA batteries.
• Car needs (4) four AA Ni-cad batteries 2000Mah OFNA #10196 or (4) Alkaline.,
Alkaline type batteries will work, but braking will be reduced and 30 minute life. The best for car, is to use a 5 cell hump receiver pack for increased voltage and longer life..
#10212 NiHm Hump Pack, see charger 10214.
Recommended Option:
You may want to upgrade the car battery pack to a Ni-Cad or NiHm 5 cell type(600AE). This will give more run time. OFNA #10212 1200NiMh Hump Pack and
NiHm Battery Charger #10214
10214
Over-nite
Charger
TOOLS NOT INCLUDED IN KIT,
BUT NEEDED TO MAINTAIN YOUR CAR.
Instant Cement
Cutter
Phillips Type Screw Drivers ( L )
Curved Scissors
#91009 $5.95
Grease
Phillips Type Screw Drivers ( S )
Cross Wrench
#17109 $3.95
Needle Nose Pliers
Knife
Glow Plug & 17MM Cross Wrench
#10801 $6.95
MUST READ THIS BEFORE RUNNING
Running a nitro kit is fun and easy, but to make this a safe and good experience you must observe a few rules. This kit is extremely fast, easily over 40MPH, and can seriously injure someone if you are not careful.
Where to run car?
• Any running area you choose must be dry. Do not run car near any water or wet dirt.
• Do not run on public streets. It is very easy to have the car run over or damaged by hitting the curb.
• Do not operate car in tight confined places. The car is very fast and will easily hit something.
• Do not run near people or animals. The car is very fast and will too easily hit someone.
• Due noise, you will want to consider the surrounding area when operating the car.
• Do not operate the car at night. You will not be able to drive it without hitting something.
• Do not operate the car indoors. Engine exhaust is not healthy.
Glow Fuel
• Glow fuel is poisonous!
• Glow fuel is flammable!
• Do not leave in fuel bottle with lid off at any time.
• Do not use any fuel other than glow fuel in this engine.
First Time Starting the Engine
Caution! When starting engine make sure the following is observed.
• Set engine Master needle to 3 turns (rich setting)
• Do not do this alone, get an experienced friend to help at first.
• Fill fuel tank, try not to spill fuel. Do not spill fuel on receiver
• Hold car off the ground, so it will not runaway when first starts
• Turn on Radio and check the linkage before starting engine.
• Turn on car receiver battery switch.
• Always have an air filter on the carburetor to keep dirt out.
Engine Break-in
• See Engine Page.
Emergency Stopping Engine When Running
• Remove air filter and cover carb. intake.
• Squeeze fuel line and hold until engine stops.
• With a rag, cover exhaust outlet.
Storing Car After Running
• Remove fuel from tank and fuel lines
• Turn off radio in car
• Put a few drops of after run in engine to keep it from rusting.
• Clean oil and dirt from chassis with a degreaser.
Precautions
• This kit is not a toy. Always run car with a second person as a spotter and pitman.
• Hot Parts - The pipe, manifold, engine and head are very hot and will cause burns.
• Rotating Parts - Keep hands away from the drive train, wheels, and engine when engine is running.
• Radio - Check batteries life before running the car. If radio does not have full control of the car with steering and/or throttle/brake do not run until corrected. Failure to correct this will result in possible injury and damage to the car or property.
• Glow fuel - Do leave the glow fuel unattended with the lid off. Fuel contains Methanol and Nitro Methane and is flammable and poisonous.
Store fuel in cool ventilated location. Refer the glow fuel label for additional precautions.
• Car Fuel tank - Never store fuel in car tank, it will ruin the engine if left in tank.
• Always turn off the car BEFORE turning off radio.
• DAMAGE DUE CAR RUN AWAY IS NOT A WARRANTY
ISSUE.
IF YOU DO NOT BREAK-IN ENGINE
CORRECTLY, MAINLY AT LOW RPM,
YOU WILL BREAK THE CONNECTING
ROD!
FAILURE TO NOT READ AND
FOLLOW BREAK-IN ENGINE
INSTRUCTIONS WILL VOID
WARRANTY!
THINGS NEEDED
RTR KITS - REQUIRED FOR OPERATION
You will need to buy a few items to start the engine and run the car.
• Use 20% nitro CAR fuel. Do not use airplane or heli fuels, they will over heat engine.
• Buy LONG glow plugs, like OFNA/PICCO Plug (#51007 or 51008).
Use plugs without idle bar. Do NOT use plugs, like the MC-59 or OS-8
In your box you will find..
• #10163 - Bottle, spout top
• #10219 - Red “D” size glow heater
Glow Fuel
20%
AA Batteries ( 12 pcs )
You need to get batteries for the radio transmitter and the car receiver packs.
• Radio TX needs (8) eight AA batteries.
• Car needs (4) four AA Ni-cad batteries 2000Mah OFNA #10196 or (4) Alkaline.,
Alkaline type batteries will work, but braking will be reduced and 30 minute life. The best for car, is to use a 5 cell hump receiver pack for increased voltage and longer life..
#10212 NiHm Hump Pack, see charger 10214.
Recommended Option:
You may want to upgrade the car battery pack to a Ni-Cad or NiHm 5 cell type(600AE). This will give more run time. OFNA #10212 1200NiMh Hump Pack and
NiHm Battery Charger #10214
10214
Over-nite
Charger
TOOLS NOT INCLUDED IN KIT,
BUT NEEDED TO MAINTAIN YOUR CAR.
Instant Cement
Cutter
Phillips Type Screw Drivers ( L )
Curved Scissors
#91009 $5.95
Grease
Phillips Type Screw Drivers ( S )
Cross Wrench
#17109 $3.95
Needle Nose Pliers
Knife
Glow Plug & 17MM Cross Wrench
#10801 $6.95
MUST READ THIS BEFORE RUNNING
Running a nitro kit is fun and easy, but to make this a safe and good experience you must observe a few rules. This kit is extremely fast, easily over 40MPH, and can seriously injure someone if you are not careful.
Where to run car?
• Any running area you choose must be dry. Do not run car near any water or wet dirt.
• Do not run on public streets. It is very easy to have the car run over or damaged by hitting the curb.
• Do not operate car in tight confined places. The car is very fast and will easily hit something.
• Do not run near people or animals. The car is very fast and will too easily hit someone.
• Due noise, you will want to consider the surrounding area when operating the car.
• Do not operate the car at night. You will not be able to drive it without hitting something.
• Do not operate the car indoors. Engine exhaust is not healthy.
Glow Fuel
• Glow fuel is poisonous!
• Glow fuel is flammable!
• Do not leave in fuel bottle with lid off at any time.
• Do not use any fuel other than glow fuel in this engine.
First Time Starting the Engine
Caution! When starting engine make sure the following is observed.
• Set engine Master needle to 3 turns (rich setting)
• Do not do this alone, get an experienced friend to help at first.
• Fill fuel tank, try not to spill fuel. Do not spill fuel on receiver
• Hold car off the ground, so it will not runaway when first starts
• Turn on Radio and check the linkage before starting engine.
• Turn on car receiver battery switch.
• Always have an air filter on the carburetor to keep dirt out.
Engine Break-in
• See Engine Page.
Emergency Stopping Engine When Running
• Remove air filter and cover carb. intake.
• Squeeze fuel line and hold until engine stops.
• With a rag, cover exhaust outlet.
Storing Car After Running
• Remove fuel from tank and fuel lines
• Turn off radio in car
• Put a few drops of after run in engine to keep it from rusting.
• Clean oil and dirt from chassis with a degreaser.
Precautions
• This kit is not a toy. Always run car with a second person as a spotter and pitman.
• Hot Parts - The pipe, manifold, engine and head are very hot and will cause burns.
• Rotating Parts - Keep hands away from the drive train, wheels, and engine when engine is running.
• Radio - Check batteries life before running the car. If radio does not have full control of the car with steering and/or throttle/brake do not run until corrected. Failure to correct this will result in possible injury and damage to the car or property.
• Glow fuel - Do leave the glow fuel unattended with the lid off. Fuel contains Methanol and Nitro Methane and is flammable and poisonous.
Store fuel in cool ventilated location. Refer the glow fuel label for additional precautions.
• Car Fuel tank - Never store fuel in car tank, it will ruin the engine if left in tank.
• Always turn off the car BEFORE turning off radio.
• DAMAGE DUE CAR RUN AWAY IS NOT A WARRANTY
ISSUE.
IF YOU DO NOT BREAK-IN ENGINE
CORRECTLY, MAINLY AT LOW RPM,
YOU WILL BREAK THE CONNECTING
ROD!
FAILURE TO NOT READ AND
FOLLOW BREAK-IN ENGINE
INSTRUCTIONS WILL VOID
WARRANTY!
NON-RTR OR PRO KITS - REQUIRED FOR OPERATION
THINGS NEED BESIDES THE KIT
3.5 cc (21 Class) ENGINE
REAR EXHAUST
OFNA/Picco
O-1 bp
#51217
Glow Fuel
20%
Glow Plug Heat with Battery & Charger
# 10227....$$19.95
(please note OFNA Glow Heats available)
Bottle’s with spout
# 10160 - large 500cc
# 10161 - large 500 ccAuto Stop
# 10162 - small 250cc
# 10164 - CNC spout 500CC
# 10167 - CNC spout 800CC
Note: Pro kit does not include engine!
Off-Road Starter Box, 12V motor
# 10250 - 1/8 scale Starter Box
# 10253 - 1/8 scale Starter Box w/ Panel
Off-Road Starter Box, two 550 motors
# 10248 - 1/8 scale Starter Box
# 10249 - 1/8 scale Starter Box,RTR
Optional Parts
# 92571 - Power Panel Glow Heater
# 92572 - Cable for Glow Plug
12V Battery for Starter Box
(must have)
AA Batteries ( 12 pcs ) for radio
RADIO CONTROL UNIT
More Optional Parts . . .
#10211 NiHm Battery Flat
Pack .. $29.95
Note: Carefully read the instruction manual of your
2 channel radio controller before using.
SUITABLE SERVO SIZE
36mm-41mm
15mm - 21mm
29mm - 42mm
Radio must be set at neutral position before installing in the kit.
SEQUENCE TO SET NEUTRAL
Install AA batteries in Radio.
Extend the antenna.(Transmitter)
Install batteries into Car receiver .
After installing the battery, connect the battery box.
Extend the antenna. (Receiver)
Set the trim-lever at center.
Turn on the switch. (Transmitter)
Turn on the switch. (Receiver)
Make sure the servos are in command.
When the operation stick is in neutral, servo horns must be in neutral as will.
*Adjustment can be made by re-
installing the servo horn.
Turn off the switch. (Receiver)
Turn off the switch. (Transmitter)
12
Retract the antenna. (Transmitter)
13
# 10214 NiHm Battery Pack
Charger.. $7.95
# 51007 or 08 OFNA/Picoo
Glow Plug .. $4.95
TOOLS NOT INCLUDED IN KIT
INCLUDED WITH KIT
Shock Oil Instant Cement
Cutter
Phillips Type Screw Drivers ( L )
Phillips Type Screw Drivers ( S )
Needle Nose Pliers
Curved Scissors
Brush
Cross Wrench
#17109 $3.95
Masking Tape
Paints
Grease Box
5mm
Hex Wrench
3mm
Hex Wrench
2.5mm
Hex Wrench
1.5mm
Hex Wrench
Glow Plug & 17MM Cross Wrench
#10801 $6.95
Knife
Grease
7mm and 5.5mm
Hex Wrench
40017
GEAR BOX PLASTIC PARTS
40015
ARM HOLDER PLASTIC PARTS
1
40027
WING SUPPORT PLASTIC PARTS
PLASTIC PARTS
40003
DIFF. CASE
PLASTIC PARTS
3
2
40013 & 40048
FRONT BUMPER & BATTERY HOLDER
PLASTIC PARTS
NON-RTR OR PRO KITS - REQUIRED FOR OPERATION
THINGS NEED BESIDES THE KIT
3.5 cc (21 Class) ENGINE
REAR EXHAUST
OFNA/Picco
O-1 bp
#51217
Glow Fuel
20%
Glow Plug Heat with Battery & Charger
# 10227....$$19.95
(please note OFNA Glow Heats available)
Bottle’s with spout
# 10160 - large 500cc
# 10161 - large 500 ccAuto Stop
# 10162 - small 250cc
# 10164 - CNC spout 500CC
# 10167 - CNC spout 800CC
Note: Pro kit does not include engine!
Off-Road Starter Box, 12V motor
# 10250 - 1/8 scale Starter Box
# 10253 - 1/8 scale Starter Box w/ Panel
Off-Road Starter Box, two 550 motors
# 10248 - 1/8 scale Starter Box
# 10249 - 1/8 scale Starter Box,RTR
Optional Parts
# 92571 - Power Panel Glow Heater
# 92572 - Cable for Glow Plug
12V Battery for Starter Box
(must have)
AA Batteries ( 12 pcs ) for radio
RADIO CONTROL UNIT
More Optional Parts . . .
#10211 NiHm Battery Flat
Pack .. $29.95
Note: Carefully read the instruction manual of your
2 channel radio controller before using.
SUITABLE SERVO SIZE
36mm-41mm
15mm - 21mm
29mm - 42mm
Radio must be set at neutral position before installing in the kit.
SEQUENCE TO SET NEUTRAL
Install AA batteries in Radio.
Extend the antenna.(Transmitter)
Install batteries into Car receiver .
After installing the battery, connect the battery box.
Extend the antenna. (Receiver)
Set the trim-lever at center.
Turn on the switch. (Transmitter)
Turn on the switch. (Receiver)
Make sure the servos are in command.
When the operation stick is in neutral, servo horns must be in neutral as will.
*Adjustment can be made by re-
installing the servo horn.
Turn off the switch. (Receiver)
Turn off the switch. (Transmitter)
12
Retract the antenna. (Transmitter)
13
# 10214 NiHm Battery Pack
Charger.. $7.95
# 51007 or 08 OFNA/Picoo
Glow Plug .. $4.95
TOOLS NOT INCLUDED IN KIT
INCLUDED WITH KIT
Shock Oil Instant Cement
Cutter
Phillips Type Screw Drivers ( L )
Phillips Type Screw Drivers ( S )
Needle Nose Pliers
Curved Scissors
Brush
Cross Wrench
#17109 $3.95
Masking Tape
Paints
Grease Box
5mm
Hex Wrench
3mm
Hex Wrench
2.5mm
Hex Wrench
1.5mm
Hex Wrench
Glow Plug & 17MM Cross Wrench
#10801 $6.95
Knife
Grease
7mm and 5.5mm
Hex Wrench
40017
GEAR BOX PLASTIC PARTS
40015
ARM HOLDER PLASTIC PARTS
1
40027
WING SUPPORT PLASTIC PARTS
PLASTIC PARTS
40003
DIFF. CASE
PLASTIC PARTS
3
2
40013 & 40048
FRONT BUMPER & BATTERY HOLDER
PLASTIC PARTS
40031
SERVO SAVER PLASTIC PARTS
PLASTIC PARTS
40047
RECEIVER BOX PLASTIC PARTS
40040
CENTER DIFF. MOUNT PLASTIC PARTS
40018/40029
CHASSIS BRACE PLASTIC PARTS
40029
40065
40019
40065
40029
40018
40056
SHOCK ABSORBER PLASTIC PARTS
40046
STONE GUARD PLASTIC PARTS
ASSEMBLY OF THE THROTTLE LINKAGE SYSTEM
#30800
Plastic Throttle kit
3X3mm
Set Screw
Throttle
Spring
2mm Rod
3X3mm
Set Screw
#10300
Alum.Stopper
#30530
Plastic Throttle
Ball Joint
Plastic Collar
* Take the plastic collar
from brake system plastic
parts.
* Snap On.
Brake
Idle Position
Note:
Battery life is short when using Alkaline batteries. For safety, we recommend using
Alkaline batteries for only 30 minutes before testing.. Battery strength affects braking power and radio range. If voltage drops while running the car, you will loose control and destroy your car! This is NOT covered under warranty.
Full Throttle
To increase run time, upgrade receiver battery to a 5-cell hump pack. But, the most important step you can make, “is to always use fully charged or fresh batteries when running your car”. Another choice is to use OFNA #10196 2000 mAh NiMh AA batteries in car and radio.
CHECKING ENGINE THROTTLE
A
1. Insert AA batteries into
transmitter (8 Pcs).
2.Turn on transmitter.
3.Turn on receiver.
4.Center throttle trims as
shown .
B
1. Pull Full Throttle.
IMPORTANT
CHECK RADIO THROTTLE
AND STEERING SWITCHES
BEFORE RUNNING CAR
C
1. Push trigger to full
brake position.
2. Adjust alum. Stopper to
increase or decrease
the brake.
* Align throttle servo same
as shown.
Brake (C)
A
Idle Position (A)
Full Throttle (B)
• Full throttle arm position.
Spring rod pulls throttle B barrel open and brake rods release pressure on brake cams.
* Insert into transmitter.
C
B A
C
3X3mm
Set Screw
Fuel
Tube
( 6mm )
#10300
Alum.Stopper
* Align throttle servo same
as shown.
• Full brake arm position.
Spring compresses forward and brake rods pull brake levers.
40031
SERVO SAVER PLASTIC PARTS
PLASTIC PARTS
40047
RECEIVER BOX PLASTIC PARTS
40040
CENTER DIFF. MOUNT PLASTIC PARTS
40018/40029
CHASSIS BRACE PLASTIC PARTS
40029
40065
40019
40065
40029
40018
40056
SHOCK ABSORBER PLASTIC PARTS
40046
STONE GUARD PLASTIC PARTS
ASSEMBLY OF THE THROTTLE LINKAGE SYSTEM
#30800
Plastic Throttle kit
3X3mm
Set Screw
Throttle
Spring
2mm Rod
3X3mm
Set Screw
#10300
Alum.Stopper
#30530
Plastic Throttle
Ball Joint
Plastic Collar
* Take the plastic collar
from brake system plastic
parts.
* Snap On.
Brake
Idle Position
Note:
Battery life is short when using Alkaline batteries. For safety, we recommend using
Alkaline batteries for only 30 minutes before testing.. Battery strength affects braking power and radio range. If voltage drops while running the car, you will loose control and destroy your car! This is NOT covered under warranty.
Full Throttle
To increase run time, upgrade receiver battery to a 5-cell hump pack. But, the most important step you can make, “is to always use fully charged or fresh batteries when running your car”. Another choice is to use OFNA #10196 2000 mAh NiMh AA batteries in car and radio.
CHECKING ENGINE THROTTLE
A
1. Insert AA batteries into
transmitter (8 Pcs).
2.Turn on transmitter.
3.Turn on receiver.
4.Center throttle trims as
shown .
B
1. Pull Full Throttle.
IMPORTANT
CHECK RADIO THROTTLE
AND STEERING SWITCHES
BEFORE RUNNING CAR
C
1. Push trigger to full
brake position.
2. Adjust alum. Stopper to
increase or decrease
the brake.
* Align throttle servo same
as shown.
Brake (C)
A
Idle Position (A)
Full Throttle (B)
• Full throttle arm position.
Spring rod pulls throttle B barrel open and brake rods release pressure on brake cams.
* Insert into transmitter.
C
B A
C
3X3mm
Set Screw
Fuel
Tube
( 6mm )
#10300
Alum.Stopper
* Align throttle servo same
as shown.
• Full brake arm position.
Spring compresses forward and brake rods pull brake levers.
ASSEMBLY OF THE DIFFERENTIAL GEAR
4x4mm
Set Screw
40006
Cap Joint
40010
2.5x13.8mm
Pin
40003
Diff. Case
36053
8x16mm
Ball bearing
40009
P6 O-Ring
40012
6x15mm
Washer
(Builds one differential for Center)
40005
Break
Cap Joint 4x4mm
Set Screw
30779
4 x 10mm washer
40004
Diff. Gear
(Small)
30779
4 x 10mm
(Small) washer
40004
Diff. Gear
30773
4mm
Cross pin
30779
4 x 10mm
40004
Diff. Gear
(Small) washer
30773
4mm
Cross pin 40004
Diff. Gear
(Small)
30779
4 x 10mm washer
40010
2.5x13.8mm
Pin
40004
Diff. Gear
(Large)
Note: It is very important to add or remove the #30779 washer if the gear mesh is too tight or too lose.
36053
8x16mm
Ball bearing
OPTION: #49001 HD STEEL GEAR SET,
INSIDE DIFF.
40003
Diff. Case
40009
P6
O-Ring 40012
6x15mm
Washer 40004
Diff. Gear
(Large)
* Apply diff. gear grease to the
differential during assembly.
* Fill the diff. the case to
approx 70% with grease.
ASSEMBLY OF THE DIFFERENTIAL CASE
40010
2.5x13.8mm
Pin
40004
Diff. Gear
(Large)
40012
6x15mm
Washer
*Use 6x15mm washer
to adjust the gear mesh.
( Builds two differentials for front and rear.)
40002
41T Large
Bevel Gear
49032
41T Large
HD Bevel Gear
36053
8x16mm
Ball bearing
40009
P6
O-Ring
40006
Cap Joint
40010
2.5x13.8mm
Pin
(Builds one differential for Center)
40012
6x15mm
Washer
40001
47T
Spur Gear
40004
Diff. Gear
(Large)
OPTION:
*Use 6x15mm washer
to adjust the gear mesh.
#49016 SPUR GEAR 50T
#49031 SPUR GEAR 50T, HD SPECIAL
40009
P6
O-Ring
36053
8x16mm
Ball bearing
40005
Break
Cap Joint
40011
Diff. Gasket
40011
Diff. Gasket
OPTION:
49032
43T Large
Bevel Gear
(must use 13t pinion)
40002
41T Large
Bevel Gear
40001
47T
Spur Gear
3x12mm
Flat Head
Tapping Screw
3x12mm
Flat Head
Tapping Screw
ASSEMBLY OF THE FRONT GEAR BOX
36053
8X16mm
Ball bearing
40017
Gear Box
36053
8X16mm
Ball bearing....4
36053
8X16mm
Ball bearing
40021
14TSmall
Bevel Gear
40024
13x16x0.2mm
Shim..............2
40024
13x16x0.2mm
Shim
40021
14T Small
Bevel Gear..............1
ASSEMBLY OF THE FRONT ARMS HOLDER
94011
4x15mm
Tapping Screw
(Small Head)
Use shims to adjust gear mesh.
OPTION: #49012 PINION GEAR
13TOOTH
40017
Gear Box
90026
5x5mm
Set Screw
36730
Cap Joint
94014
4x45mm
Tapping Screw
(Small Head)
MISC. SCREW BAG
40067
4x15mm
Tapping Screw........................2
90026
5x5mm
Set Screw......1
40022
Front Lower Arm
Holder (Front)
36730
Cap Joint................................1
4 x 16mm
Flat Head
Tapping Screw.......................4
4x45mm
Tapping Screw........................2
40015
Front Lower arm
Holder (Rear/Plastic)
4x16mm
Flat Head
Tapping Screw
40015
Front Upper arm
Holder (Rear/Plastic)
OPTION: #49002 CNC 7075
FRONT LOWER ARM HOLDER
94027
4x16mm
Flat Head
Tapping Screw
ASSEMBLY OF THE DIFFERENTIAL GEAR
4x4mm
Set Screw
40006
Cap Joint
40010
2.5x13.8mm
Pin
40003
Diff. Case
36053
8x16mm
Ball bearing
40009
P6 O-Ring
40012
6x15mm
Washer
(Builds one differential for Center)
40005
Break
Cap Joint 4x4mm
Set Screw
30779
4 x 10mm washer
40004
Diff. Gear
(Small)
30779
4 x 10mm
(Small) washer
40004
Diff. Gear
30773
4mm
Cross pin
30779
4 x 10mm
40004
Diff. Gear
(Small) washer
30773
4mm
Cross pin 40004
Diff. Gear
(Small)
30779
4 x 10mm washer
40010
2.5x13.8mm
Pin
40004
Diff. Gear
(Large)
Note: It is very important to add or remove the #30779 washer if the gear mesh is too tight or too lose.
36053
8x16mm
Ball bearing
OPTION: #49001 HD STEEL GEAR SET,
INSIDE DIFF.
40003
Diff. Case
40009
P6
O-Ring 40012
6x15mm
Washer 40004
Diff. Gear
(Large)
* Apply diff. gear grease to the
differential during assembly.
* Fill the diff. the case to
approx 70% with grease.
ASSEMBLY OF THE DIFFERENTIAL CASE
40010
2.5x13.8mm
Pin
40004
Diff. Gear
(Large)
40012
6x15mm
Washer
*Use 6x15mm washer
to adjust the gear mesh.
( Builds two differentials for front and rear.)
40002
41T Large
Bevel Gear
49032
41T Large
HD Bevel Gear
36053
8x16mm
Ball bearing
40009
P6
O-Ring
40006
Cap Joint
40010
2.5x13.8mm
Pin
(Builds one differential for Center)
40012
6x15mm
Washer
40001
47T
Spur Gear
40004
Diff. Gear
(Large)
OPTION:
*Use 6x15mm washer
to adjust the gear mesh.
#49016 SPUR GEAR 50T
#49031 SPUR GEAR 50T, HD SPECIAL
40009
P6
O-Ring
36053
8x16mm
Ball bearing
40005
Break
Cap Joint
40011
Diff. Gasket
40011
Diff. Gasket
OPTION:
49032
43T Large
Bevel Gear
(must use 13t pinion)
40002
41T Large
Bevel Gear
40001
47T
Spur Gear
3x12mm
Flat Head
Tapping Screw
3x12mm
Flat Head
Tapping Screw
ASSEMBLY OF THE FRONT GEAR BOX
36053
8X16mm
Ball bearing
40017
Gear Box
36053
8X16mm
Ball bearing....4
36053
8X16mm
Ball bearing
40021
14TSmall
Bevel Gear
40024
13x16x0.2mm
Shim..............2
40024
13x16x0.2mm
Shim
40021
14T Small
Bevel Gear..............1
ASSEMBLY OF THE FRONT ARMS HOLDER
94011
4x15mm
Tapping Screw
(Small Head)
Use shims to adjust gear mesh.
OPTION: #49012 PINION GEAR
13TOOTH
40017
Gear Box
90026
5x5mm
Set Screw
36730
Cap Joint
94014
4x45mm
Tapping Screw
(Small Head)
MISC. SCREW BAG
40067
4x15mm
Tapping Screw........................2
90026
5x5mm
Set Screw......1
40022
Front Lower Arm
Holder (Front)
36730
Cap Joint................................1
4 x 16mm
Flat Head
Tapping Screw.......................4
4x45mm
Tapping Screw........................2
40015
Front Lower arm
Holder (Rear/Plastic)
4x16mm
Flat Head
Tapping Screw
40015
Front Upper arm
Holder (Rear/Plastic)
OPTION: #49002 CNC 7075
FRONT LOWER ARM HOLDER
94027
4x16mm
Flat Head
Tapping Screw
ASSEMBLY OF THE FRONT SHOCK TOWER
4mm
Nylon Nut
40014
Front
Shock Tower
M4x15
TP Screw
OPTION: 49003
CNC 7075 Alum. Shock Tower
94004
M3x12
TP Screw
ASSEMBLY OF THE FRONT KNUCKLE ARMS
Assembly of the left and gight hand side are the same.
36055
2.5x17mm
Pin
S crew
C e m ent
40103
Front
Knuckle Arm
* "R" for right hand
side.
40105
8mm CVA Joint
(Long/Front)
40103
Front
Knuckle Arm
36055
2.5x17mm
Pin
90026
5mm
Set Screw
36054
Alum.
36053
8x16x5mm
Wheel Hub 8mm
Bal lbearing
36053
8x16x5mm
Ball bearing
Sc
Ce rew ment
36054
Alum.
Wheel Hub 8mm
36053
8x16x5mm
Bal lbearing
90026
5mm
Set Screw
ASSEMBLY OF THE FRONT LOWER ARMS
* A 4 x 10mm set screw is used
to adjust the ride height.
*Notice the direction
of the steering ball.
36870
4X10mm
Set Screw 2mm
40105
8mm CVA Joint
(Long/Front)
36053
8x16x5mm
Bal lbearing
4014
10mm
Steering Ball
36870
4X10mm
Set Screw
40104
10mm
Steering Ball
Assembly of the left and gight hand side are the same.
40101
Upper Arm
Ball End
*Notice the direction
of the steering ball.
40101
Upper Arm
Ball End
40104
10mm
Steering Ball
40102
Front
Lower Arm
40102
Front
Lower Arm
40104
10mm
Steering Ball
ASSEMBLY OF THE FRONT UPPER ARMS
40101
Front
Upper Arm
36860
5x40mm
Turnbuckle
40101
Front
Upper Arm
Ball End
(Right)
ASSEMBLY OF THE FRONT LOWER ARMS
90020
2.5mm
E-Ring
36170
Arm Shalf
3mmt
(Left)
10mm
0 10 20 30 40 50 mm
Assembly of the right and left hand side are the same.
90021
3mm
E-Ring
90020
2.5mm
E-Ring
40023
Lower Arm Shaft (4mm)
90021
3mm
E-Ring
Assembly of the right and left hand side are the same.
ASSEMBLY OF THE FRONT SUSPENSION ARMS
Caster
Adjuster
* Insert the caster adjuster
into upper arm.
40104
4x16mm
Cap Screw
Sc rew
Cement
Sc rew
Cement
40104
4x16mm
Cap Screw
* Insert the drive shaft
into cap joint before assembly.
ASSEMBLY OF THE FRONT SHOCK TOWER
4mm
Nylon Nut
40014
Front
Shock Tower
M4x15
TP Screw
OPTION: 49003
CNC 7075 Alum. Shock Tower
94004
M3x12
TP Screw
ASSEMBLY OF THE FRONT KNUCKLE ARMS
Assembly of the left and gight hand side are the same.
36055
2.5x17mm
Pin
S c re w
C e m e n t
40103
Front
Knuckle Arm
* "R" for right hand
side.
40105
8mm CVA Joint
(Long/Front)
40103
Front
Knuckle Arm
36055
2.5x17mm
Pin
90026
5mm
Set Screw
36054
Alum.
36053
8x16x5mm
Wheel Hub 8mm
Bal lbearing
36053
8x16x5mm
Ball bearing
Sc
Cement
36054
Alum.
Wheel Hub 8mm
36053
8x16x5mm
Bal lbearing
90026
5mm
Set Screw
ASSEMBLY OF THE FRONT LOWER ARMS
* A 4 x 10mm set screw is used
to adjust the ride height.
*Notice the direction
of the steering ball.
36870
4X10mm
Set Screw 2mm
40105
8mm CVA Joint
(Long/Front)
36053
8x16x5mm
Bal lbearing
4014
10mm
Steering Ball
36870
4X10mm
Set Screw
40104
10mm
Steering Ball
Assembly of the left and gight hand side are the same.
40101
Upper Arm
Ball End
*Notice the direction
of the steering ball.
40101
Upper Arm
Ball End
40104
10mm
Steering Ball
40102
Front
Lower Arm
40102
Front
Lower Arm
40104
10mm
Steering Ball
ASSEMBLY OF THE FRONT UPPER ARMS
40101
Front
Upper Arm
36860
5x40mm
Turnbuckle
40101
Front
Upper Arm
Ball End
(Right)
ASSEMBLY OF THE FRONT LOWER ARMS
90020
2.5mm
E-Ring
36170
Arm Shalf
3mmt
(Left)
10mm
0 10 20 30 40 50 mm
Assembly of the right and left hand side are the same.
90021
3mm
E-Ring
90020
2.5mm
E-Ring
40023
Lower Arm Shaft (4mm)
90021
3mm
E-Ring
Assembly of the right and left hand side are the same.
ASSEMBLY OF THE FRONT SUSPENSION ARMS
Caster
Adjuster
* Insert the caster adjuster
into upper arm.
40104
4x16mm
Cap Screw
Sc rew
Cement
Sc rew
Ceme nt
40104
4x16mm
Cap Screw
* Insert the drive shaft
into cap joint before assembly.
ASSEMBLY OF THE FRONT STABILIZER
40029
Stabilizer
Ball End
(Long)
30341
Stabilizer Ball
40029
Stabilizer
Ball End
3x8mm
Set Screw
30401
6mm
Ball End
94007
3x20mm
Screw
30341
A34B
Stabilizer Ball..........2
94007
3 x 20mm
Screw ......................2
94033
3 x 3mm
Set Screw..............4
94019
3 x 10mm
Flat Head
Tapping Screw........2
94004
3 x 12mm
Tapping Screw..........1
94027
4 x 16mm
Flat Head
Tapping Screw..........4
94033
3x3
Set Screw
94007
3x20mm
Screw
94033
3x3
Set Screw
40018
Stabilizer
Mount Plastic
94019
3x10mm
Flat Head
Tapping Screw
40019
Stabilizer
94019
3x10mm
Flat Head
Tapping Screw
94033
3x3
Set Screw
40013
Front
Bumper
* Insert the front bumper
before assembly.
40064
Chassis
94004
3X12mm
Tapping Screw
4x16mm
Flat Head
Tapping Screw
ASSEMBLY OF THE WING STAY
( Take the plastic part from #40027Rear Win Stay Set. )
49038
Rear
Shock Tower, Orange
40027
Rear
Body Mount
40027
Wing Mount
40027
Wing Stay
( Left )
3x20
Tapping Screw
3x12mm
Tapping Screw
40027
Wing Stay
Post
40027
Wing Mount
40027
Wing Mount
40027
Wing Stay
( Right )
35313
3mm
Nylon Nut
*Insert the 3mm nylon nut
before assembly.
94007
3x20
Tapping Screw
40027
Wing Mount
OPTION: #49043 CNC ALIM.
POSTS, WING MOUNT, ORANGE
3 x 12mm
Tapping Screw........3
3mm
Nylon Nut........2
3 x 20mm
Tapping Screw............6
4 x 15mm
Tapping Screw
( Small Head )............2
4 x 15mm
Tapping Screw
( Small Head )............4
OPTION: #49004 CNC 7075
REAR SHOCK TOWER
94004
3x12mm
Tapping Screw
94011
4x15mm
Tapping Screw
( Small Head )
94011
4x15mm
Tapping Screw
( Small Head )
94012
4x20mm
Screw
( Small Head )
ASSEMBLY OF THE FRONT STABILIZER
40029
Stabilizer
Ball End
(Long)
30341
Stabilizer Ball
40029
Stabilizer
Ball End
3x8mm
Set Screw
30401
6mm
Ball End
94007
3x20mm
Screw
30341
A34B
Stabilizer Ball..........2
94007
3 x 20mm
Screw ......................2
94033
3 x 3mm
Set Screw..............4
94019
3 x 10mm
Flat Head
Tapping Screw........2
94004
3 x 12mm
Tapping Screw..........1
94027
4 x 16mm
Flat Head
Tapping Screw..........4
94033
3x3
Set Screw
94007
3x20mm
Screw
94033
3x3
Set Screw
40018
Stabilizer
Mount Plastic
94019
3x10mm
Flat Head
Tapping Screw
40019
Stabilizer
94019
3x10mm
Flat Head
Tapping Screw
94033
3x3
Set Screw
40013
Front
Bumper
* Insert the front bumper
before assembly.
40064
Chassis
94004
3X12mm
Tapping Screw
4x16mm
Flat Head
Tapping Screw
ASSEMBLY OF THE WING STAY
( Take the plastic part from #40027Rear Win Stay Set. )
49038
Rear
Shock Tower, Orange
40027
Rear
Body Mount
40027
Wing Mount
40027
Wing Stay
( Left )
3x20
Tapping Screw
3x12mm
Tapping Screw
40027
Wing Stay
Post
40027
Wing Mount
40027
Wing Mount
40027
Wing Stay
( Right )
35313
3mm
Nylon Nut
*Insert the 3mm nylon nut
before assembly.
94007
3x20
Tapping Screw
40027
Wing Mount
OPTION: #49043 CNC ALIM.
POSTS, WING MOUNT, ORANGE
3 x 12mm
Tapping Screw........3
3mm
Nylon Nut........2
3 x 20mm
Tapping Screw............6
4 x 15mm
Tapping Screw
( Small Head )............2
4 x 15mm
Tapping Screw
( Small Head )............4
OPTION: #49004 CNC 7075
REAR SHOCK TOWER
94004
3x12mm
Tapping Screw
94011
4x15mm
Tapping Screw
( Small Head )
94011
4x15mm
Tapping Screw
( Small Head )
94012
4x20mm
Screw
( Small Head )
ASSEMBLY OF THE REAR GEAR BOX ONTO CHASSIS
36055
2.5x17mm
36081
Rear
36082
Rear
36053
8x16x5mm
Wheel Shaft
Ball bearing
Pin Upper Right
3 x10x3mm
Plastic Washer
36054
8mm
Wheel Hub
36053
8x16x5mm
Bal l bearing
3 x10x3mm
Plastic Washer
90026
5mm
Set Screw
Assembly of the right and left hand side are the same.
* A 4 x 10mm set screw is used
to adjust the ride height.
4X10mm
Set Screw
40102
Rear
Lower arm
5 x 5mm
Set Screw............2
4 x 10 mm
Set Screw...........2
2.5mm
E-Ring..........4
3 mm
E-Ring..........4
90020
2.5mm
E-Ring
90021
3mm
E-Ring
40023
Lower Arm Shaft
36170
3mm
Arm Shaft
90020
2.5mm
E-Ring
40102
Rear
Lower arm
3mm
90021
E-Ring
3mm
90021
E-Ring
ASSEMBLY OF THE REAR UPPER ARMS
(Make two upper arms for left an right hand side. )
40065
Upper Arm
Plastic Rod End
36860
5x40mm
Turnbuckle
40065
Upper Arm
Plastic Rod End
40065
Upper Arm
Plastic Rod End
36850
7mm Ball
36850
7mm Ball
36850
7mm Ball
40065
Upper Arm
Plastic Rod End
36860
5x40mm
Turnbuckle
16mm
ASSEMBLY OF THE REAR AND ANTI-ROLL BAR
35313
3mm
Nylon Nut
Assembly of the right and left hand side are the same.
Rear Upper Arm
Assembly
30341
Stabilizer Ball..........2
94007
3 x 20mm
Screw ......................2
94033
3 x 3mm
Set Screw..............2
94035
3 x 8mm et Screw..........2.
94020
3 x 12mm
Tapping Screw..........1
40166
Stabilizer
Ball End
(Long)
30341
Stabilizer Ball
35313
3mm
Nylon Nut
3 x 25mm
Cap Screw
94007
3x20mm
Screw
* Insert rear driver shaft
before assembly.
40107
Rear
Driver Shaft
(101mm)
94007
3 x 20mm
Cap Screw
40029
Stabilizer
Ball End
3x8mm
Set Screw
30401
6mm
Ball End
94007
3x20mm
Screw
94033
3x3
Set Screw
94033
3x3
Set Screw
94007
3 x 20mm
Cap Screw..........2
35313
M3
Nylon Nut..........2
90018
3 X 25mm
Cap Screw.........2
94033
3 x 3mm
Set Screw..........2
94019
3 x 10mm
Flat Head
Tapping Screw........2
94019
3X10mm
Flat Head
Screw
40019
Stabilizer
40018
Stabilizer
Mount Plastic
94019
3X10mm
Flat Head
Screw
94033
3x3
Set Screw
ASSEMBLY OF THE REAR GEAR BOX ONTO CHASSIS
36055
2.5x17mm
36081
Rear
36082
Rear
36053
8x16x5mm
Wheel Shaft
Ball bearing
Pin Upper Right
3 x10x3mm
Plastic Washer
36054
8mm
Wheel Hub
36053
8x16x5mm
Bal l bearing
3 x10x3mm
Plastic Washer
90026
5mm
Set Screw
Assembly of the right and left hand side are the same.
* A 4 x 10mm set screw is used
to adjust the ride height.
4X10mm
Set Screw
40102
Rear
Lower arm
5 x 5mm
Set Screw............2
4 x 10 mm
Set Screw...........2
2.5mm
E-Ring..........4
3 mm
E-Ring..........4
90020
2.5mm
E-Ring
90021
3mm
E-Ring
40023
Lower Arm Shaft
36170
3mm
Arm Shaft
90020
2.5mm
E-Ring
40102
Rear
Lower arm
3mm
90021
E-Ring
3mm
90021
E-Ring
ASSEMBLY OF THE REAR UPPER ARMS
(Make two upper arms for left an right hand side. )
40065
Upper Arm
Plastic Rod End
36860
5x40mm
Turnbuckle
40065
Upper Arm
Plastic Rod End
40065
Upper Arm
Plastic Rod End
36850
7mm Ball
36850
7mm Ball
36850
7mm Ball
40065
Upper Arm
Plastic Rod End
36860
5x40mm
Turnbuckle
16mm
ASSEMBLY OF THE REAR AND ANTI-ROLL BAR
35313
3mm
Nylon Nut
Assembly of the right and left hand side are the same.
Rear Upper Arm
Assembly
30341
Stabilizer Ball..........2
94007
3 x 20mm
Screw ......................2
94033
3 x 3mm
Set Screw..............2
94035
3 x 8mm et Screw..........2.
94020
3 x 12mm
Tapping Screw..........1
40166
Stabilizer
Ball End
(Long)
30341
Stabilizer Ball
35313
3mm
Nylon Nut
3 x 25mm
Cap Screw
94007
3x20mm
Screw
* Insert rear driver shaft
before assembly.
40107
Rear
Driver Shaft
(101mm)
94007
3 x 20mm
Cap Screw
40029
Stabilizer
Ball End
3x8mm
Set Screw
30401
6mm
Ball End
94007
3x20mm
Screw
94033
3x3
Set Screw
94033
3x3
Set Screw
94007
3 x 20mm
Cap Screw..........2
35313
M3
Nylon Nut..........2
90018
3 X 25mm
Cap Screw.........2
94033
3 x 3mm
Set Screw..........2
94019
3 x 10mm
Flat Head
Tapping Screw........2
94019
3X10mm
Flat Head
Screw
40019
Stabilizer
40018
Stabilizer
Mount Plastic
94019
3X10mm
Flat Head
Screw
94033
3x3
Set Screw
94027
4 x 16mm
Flat Head
Tapping Screw..........4
40064
Chassis
ASSEMBLY OF THE SERVO SAVER
35313
M3 Nut..........1
40035
Servo Saver
Alum. Axle
Tube
40031
Servo Saver
Horn A
4x10mm
Screw..........2
40037
Steering Plat
Hex Screw....... 2
OPTION: #49014 CNC BALL
BEARING AXLE TUBE
M3 Nut
* Put the 3mm
nut before assembly.
40074
6x10mm
Ball bearing
40034
Servo Saver
Spring Tension
Adjuster
40031
Servo Saver
Horn B
40033
Servo Saver
Spring
94027
4 x 16mm
Flat Head
Tapping Screw
40037
Steering Plate
Hex Screw
40037
Steering Plate
Hex Screw
4x8mm
Plastic flange
Bushing
Option:
40073
4x8mm
Ball bearing flange
40036 servo Saver
Post
40095
Servo Saver
Connecting Plate,
Orange
6x10mm
Plastic
Bushing
Servo Saver
Horn C
6x10mm
Plastic
Bushing
40036
Servo Saver
Post
Option:
40074
6x10mm
Ball bearing
* Take the 4x8mm Plastic Flange bushing
and Plastic Bushing from servo saver plastic
parts tree
ASSEMBLY OF THE SERVO SAVER ONTO THE CHASSIS
4x10mm
Screw
94009
4x10mm
Screw..........2
94004
3 x 12mm
Tapping Screw..........1
40030
Front Plate
94011
4 x 15mm
Tapping Screw
( Small Head )............2
94026
4 x 10mm
Flat Head Screw..........2
4x15mm
Tapping Screw
40027
Front Body
Post
* Assembly the front body post
before assembly the Front Plate.
3x12mm
Screw
4x10mm
Flat Head
Screw
OPTION:
49005
CNC 7075 Alum. Front Plate
49019
Graphite Front Plate
ASSEMBLY OF THE FRONT STEERING ROD
* Made two steering rods for left and right hand side.
40018
4x56mm
Turnbuckle
35313
M3
Nylon Nut..........2
36850
7mm Ball
40039
Alum. Tapper
Washer................4
36700
Steering
Ball End
35313
3mm
Nylon Nut
94021
3 x 15mm
Flat Head
Screw..........4
40039
3mm Tapper
Washer(Alum.)
3x15mm
Flat Head
Screw
3x15mm
Flat Head
Screw
40039
3mm Tapper
Washer(Alum.)
36850
7mm Ball
36700
Steering
Ball End
40018
4x56mm
Turnbuckle
Assembly of the right and left hand side are the same.
0 10 20 30 40 50 mm
* Anticlockwise mark.
35.5mm
36700
Steering
Ball End
36850
7mm Ball
94027
4 x 16mm
Flat Head
Tapping Screw..........4
40064
Chassis
ASSEMBLY OF THE SERVO SAVER
35313
M3 Nut..........1
40035
Servo Saver
Alum. Axle
Tube
40031
Servo Saver
Horn A
4x10mm
Screw..........2
40037
Steering Plat
Hex Screw....... 2
OPTION: #49014 CNC BALL
BEARING AXLE TUBE
M3 Nut
* Put the 3mm
nut before assembly.
40074
6x10mm
Ball bearing
40034
Servo Saver
Spring Tension
Adjuster
40031
Servo Saver
Horn B
40033
Servo Saver
Spring
94027
4 x 16mm
Flat Head
Tapping Screw
40037
Steering Plate
Hex Screw
40037
Steering Plate
Hex Screw
4x8mm
Plastic flange
Bushing
Option:
40073
4x8mm
Ball bearing flange
40036 servo Saver
Post
40095
Servo Saver
Connecting Plate,
Orange
6x10mm
Plastic
Bushing
Servo Saver
Horn C
6x10mm
Plastic
Bushing
40036
Servo Saver
Post
Option:
40074
6x10mm
Ball bearing
* Take the 4x8mm Plastic Flange bushing
and Plastic Bushing from servo saver plastic
parts tree
ASSEMBLY OF THE SERVO SAVER ONTO THE CHASSIS
4x10mm
Screw
94009
4x10mm
Screw..........2
94004
3 x 12mm
Tapping Screw..........1
40030
Front Plate
94011
4 x 15mm
Tapping Screw
( Small Head )............2
94026
4 x 10mm
Flat Head Screw..........2
4x15mm
Tapping Screw
40027
Front Body
Post
* Assembly the front body post
before assembly the Front Plate.
3x12mm
Screw
4x10mm
Flat Head
Screw
OPTION:
49005
CNC 7075 Alum. Front Plate
49019
Graphite Front Plate
ASSEMBLY OF THE FRONT STEERING ROD
* Made two steering rods for left and right hand side.
40018
4x56mm
Turnbuckle
35313
M3
Nylon Nut..........2
36850
7mm Ball
40039
Alum. Tapper
Washer................4
36700
Steering
Ball End
35313
3mm
Nylon Nut
94021
3 x 15mm
Flat Head
Screw..........4
40039
3mm Tapper
Washer(Alum.)
3x15mm
Flat Head
Screw
3x15mm
Flat Head
Screw
40039
3mm Tapper
Washer(Alum.)
36850
7mm Ball
36700
Steering
Ball End
40018
4x56mm
Turnbuckle
Assembly of the right and left hand side are the same.
0 10 20 30 40 50 mm
* Anticlockwise mark.
35.5mm
36700
Steering
Ball End
36850
7mm Ball
ASSEMBLY OF THE BRAKE AND SPLIT CENTER DIFF. MOUNT
* Make brake pads for each side.
* Take off the double sided paper
before assembly.
36660
Brake Pad
40045
Brake Pad
Adjustment Screw
36661
Brake Pad linings
40044
Brake Pad
Spring
40040
Center Diff.
Mount 40044
Brake Pad
Spring
40044
Brake Pad
Spring
40040
Center Diff.
Mount
40044
Brake Pad
Spring
OPTION: #49030 CNC 7075 SPLIT
CENTER DIFF MOUNT.
Assembly the brake disc holder
in the direction shown.
Large
Hole
Small
Hole
Small hole to the
Outside.
40040
Brake Disk
Holder
*Towards
the front.
40040
Center Diff.
Mount
40040
Break Disc
Holder
40045
Brake Pad
Adjustment Screw
40040
Center Diff.
Mount
*Towards
the Rear.
40040
Brake Disc
Holder
40045
Brake Pad Screw...........4
40044
Brake Pad
Spring.........8
40043
Center Diff. Mount
Post...........................4
40043
Center Diff. Mount
Post
ASSEMBLY OF THE CENTER DIFF. INTO CENTER DIFF. MOUNT
Center Diff. Assembly
40042
Brake Disk
40042
Brake Disk
40042
Brake Disk
40042
Brake Disk
94003
3x10mm
Screw..........4
94033
3 x 3mm
Set Screw..............2
30171
Brake Lever..........2
OPTION: #49008 GRAPHITE
BRAKE DISKS, 2PCS.
3x10mm
Screw
Screw
Cement
Option
30212
5X8mm
Ball Bearing
30211
Plastic
Bushing
30213
Brake Cam
40096
Center Diff.
Plate, Orange
30171
Brake Lever
3x3mm
Set Screw
30171
Brake Lever
3x3mm
Set Screw
Screw
Cement
3x10mm
Screw
40031
Fuel Overflow
Proof Plate
Put the front brake lever as
Shown.
OPTION: #49018 GRAPHITE
TOP CENTER PLATE
ASSEMBLY OF THE BRAKE AND SPLIT CENTER DIFF. MOUNT
* Make brake pads for each side.
* Take off the double sided paper
before assembly.
36660
Brake Pad
40045
Brake Pad
Adjustment Screw
36661
Brake Pad linings
40044
Brake Pad
Spring
40040
Center Diff.
Mount 40044
Brake Pad
Spring
40044
Brake Pad
Spring
40040
Center Diff.
Mount
40044
Brake Pad
Spring
OPTION: #49030 CNC 7075 SPLIT
CENTER DIFF MOUNT.
Assembly the brake disc holder
in the direction shown.
Large
Hole
Small
Hole
Small hole to the
Outside.
40040
Brake Disk
Holder
*Towards
the front.
40040
Center Diff.
Mount
40040
Break Disc
Holder
40045
Brake Pad
Adjustment Screw
40040
Center Diff.
Mount
*Towards
the Rear.
40040
Brake Disc
Holder
40045
Brake Pad Screw...........4
40044
Brake Pad
Spring.........8
40043
Center Diff. Mount
Post...........................4
40043
Center Diff. Mount
Post
ASSEMBLY OF THE CENTER DIFF. INTO CENTER DIFF. MOUNT
Center Diff. Assembly
40042
Brake Disk
40042
Brake Disk
40042
Brake Disk
40042
Brake Disk
94003
3x10mm
Screw..........4
94033
3 x 3mm
Set Screw..............2
30171
Brake Lever..........2
OPTION: #49008 GRAPHITE
BRAKE DISKS, 2PCS.
3x10mm
Screw
Screw
Cement
Option
30212
5X8mm
Ball Bearing
30211
Plastic
Bushing
30213
Brake Cam
40096
Center Diff.
Plate, Orange
30171
Brake Lever
3x3mm
Set Screw
30171
Brake Lever
3x3mm
Set Screw
Screw
Cement
3x10mm
Screw
40031
Fuel Overflow
Proof Plate
Put the front brake lever as
Shown.
OPTION: #49018 GRAPHITE
TOP CENTER PLATE
ASSEMBLY OF THE CENTER DIFF. ONTO CHASSIS
40028
Center Drive
Shaft (93mm)
40028
Center Drive
Shaft (93mm)
94026
4 x 12mm
Flat Head Screw..........2
4x12mm
Flat Head
Screw
ASSEMBLY OF THE CENTER STIFFENER
ONTO CHASSIS
40018
Center Chassis
Brace
( Rear )
3x25mm
Cap Screw
3mm
Nylon Nut
40018
Center Chassis
Brace
( Front )
OPTION:
49015
CNC Alum. Chassis Brace Set
3x12mm
Screw
94004
3 x 12mm
Tapping Screw........3
35313
3mm
Nylon Nut........1
90019
3 X 25mm
Cap Screw.........1
94027
4 x 16mm
Flat Head
Tapping Screw..........4
2.6x10mm
Flat Head
4x16mm
Flat Head
Tapping Screw
Tapping Screw
4x16mm
Flat Head
Tapping Screw
4x16mm
Flat Head
Tapping Screw
ASSEMBLY OF THE STONE GUIDE
3x10mm
Screw
40046
Stone Guard
3 x 10mm
Tapping Screw..........6
ASSEMBLY OF THE RECEIVER BOX
2x10mm
Tapping Screw
* Use the screw provided
with your radio
40047
Receiver Box
3x10mm
Screw
3x10mm
Screw
40898
2x25mm
Screw
40046
Stone Guard
Assembly of the right and left hand side are the same.
OPTION:
Stone Guard
Yellow . 40078
Red . 40079
Lime . 40080
Blue . 40081
Black . 40046
40047
Receiver Box
Cover
10280
Switch Cover
Switch, Provided by Radio
2 x10mm
Tapping Screw..........2
2 x 25mm Screw.....1
94003
3 x 10mm
Tapping Screw..........1
40047
Receiver Box
* You must add padding for radio and battery once lid is closed.
Do not let radio and/or battery be loose in box.
Receiver
3x10mm
Screw
*Use the original battery
case or rechargeable
hump pack battery.
Battery Case,
Provided by
Radio
30560
Antenna
Pipe
Option:
10212
Hump Pack
Battery
ASSEMBLY OF THE CENTER DIFF. ONTO CHASSIS
40028
Center Drive
Shaft (93mm)
40028
Center Drive
Shaft (93mm)
94026
4 x 12mm
Flat Head Screw..........2
4x12mm
Flat Head
Screw
ASSEMBLY OF THE CENTER STIFFENER
ONTO CHASSIS
40018
Center Chassis
Brace
( Rear )
3x25mm
Cap Screw
3mm
Nylon Nut
40018
Center Chassis
Brace
( Front )
OPTION:
49015
CNC Alum. Chassis Brace Set
3x12mm
Screw
94004
3 x 12mm
Tapping Screw........3
35313
3mm
Nylon Nut........1
90019
3 X 25mm
Cap Screw.........1
94027
4 x 16mm
Flat Head
Tapping Screw..........4
2.6x10mm
Flat Head
4x16mm
Flat Head
Tapping Screw
Tapping Screw
4x16mm
Flat Head
Tapping Screw
4x16mm
Flat Head
Tapping Screw
ASSEMBLY OF THE STONE GUIDE
3x10mm
Screw
40046
Stone Guard
3 x 10mm
Tapping Screw..........6
ASSEMBLY OF THE RECEIVER BOX
2x10mm
Tapping Screw
* Use the screw provided
with your radio
40047
Receiver Box
3x10mm
Screw
3x10mm
Screw
40898
2x25mm
Screw
40046
Stone Guard
Assembly of the right and left hand side are the same.
OPTION:
Stone Guard
Yellow . 40078
Red . 40079
Lime . 40080
Blue . 40081
Black . 40046
40047
Receiver Box
Cover
10280
Switch Cover
Switch, Provided by Radio
2 x10mm
Tapping Screw..........2
2 x 25mm Screw.....1
94003
3 x 10mm
Tapping Screw..........1
40047
Receiver Box
* You must add padding for radio and battery once lid is closed.
Do not let radio and/or battery be loose in box.
Receiver
3x10mm
Screw
*Use the original battery
case or rechargeable
hump pack battery.
Battery Case,
Provided by
Radio
30560
Antenna
Pipe
Option:
10212
Hump Pack
Battery
ASSEMBLY OF THE RADIO TRAY
3x10mm
Tapping Screw
3x10mm
Tapping Screw
49039
Alum.
Radio Tray, Orange
Throttle
Servo
3x10
Tapping Screw
Steering
Servo
3x10
Tapping Screw
OPTION:
49044 CNC ALUM. POST,
RADIO TRAY, ORANGE
40027
Radio Tray
Post
( Plastic )
40027
Radio Tray
Post
( Plastic )
3x12mm
Tapping Screw
10274
Servo Post
Servo Post
* Take the servo post
from servo saver plastic
part tree.
94003
3 x 10mm
Tapping Screw..........14
94019
3 x 10mm
Flat Head
Tapping Screw.........8
3X10mm
Tapping Screw
*Connect as per radio.
OPTION:
49017 GRAPHITE RADIO
TRAY.
3 x 5mm Screw
3 X 8mm
Washer
ASSEMBLY OF THE CLUTCH INTO ENGINE
Notes:
Non-Pull Start Engines...
• Alum. Washer behind the flywheel is not needed when using Force engines or similar types. O.S. Engines will require washer spacer.
• To check!..place the brass corn against the engine bearing, then flywheel. You should be covering one or two thread of the engine shaft. If this is the case, you do not need an additional washer behind the flywheel.
You must cut the engine shaft if too long. Count 6 threads in front of the flywheel and mark. This is all you need to tighten the clutch nut and mount the flywheel.
Force Pull Start Engine w/threaded shalf...
• Force Pull Start Engines required NO spacer and no shaft cutting. The engines comes with an alum cast driver washer, you use this part as the spacer, not the alum. washer shown. Also, use the special flywheel brass corn.
This corn fits the thread shaft diameter so you can tighten the flywheel against the drive hub.
30481
3 x 20mm
Hex Screw
30481
3 x 20mm
Hex Screw 3 x 20mm
Cap Screw
3mm Nylon
Locknut
#10398 - 12T
#10399 - 13T
#10400 - 14T (stock)
#10401 - 15T
#10402 - 16T
#10403 - 17T
#10404 - 18T
Clutch Bells
#10102
Clutch Spring
#10010
Clutch Shoes
Black Type
#10330
Brass, Corn
(large hole)
Note
SG Shaft
30481
3 x 20mm
Hex Screw
#34110
5x10x4mm
Ball Bearing
3 x 5mm
Screw
3 x 8mm
Washer
Misc. Hardware
#10099
* Fit the flywheel using a cross wrench or deep socket.
If engine turns when tightening, hold piston with large thick tie-wraps and hard wood in exhaust port.
Do not use metal, it will damage engine.
#34110
5x10x4mm
Ball Bearing
#10098
SG Nut
& Shim KiT
#10091
Clutch Nut screw type
* Shoes are
trailing.
* Place the clutch shoes
with the clutch springs
over the 3 pins of the
flywheel.
Using a screw driver as a lever,
bend the small end of the
clutch spring behind the
clutch nut and press
down to snap shoe in
place.
Option
10799
Flywheel Wrench
#10329
Brass, Corn
(sml hole)
Threaded
Shaft
#10040 (stock)
3 Pin
Flywheel, Taper
#10043
3 Pin
Flywheel, Fan
SEE NOTES
ABOVE
#10048
OR 10049
#30480
Engine Mount
Options
Clutch Spring
10100 - Springs, Polished, Med.
10101 - Spring, Gray, Hard
10102 - Spring, Black, Stock
Clutch Shoes, 3 shoe clutch
10010 - Shoes, Carbon Material, Black
10011 - Shoes, Alum. CNC Blue, Lite Weight
10012 - Shoe, Alum. CNC Purple, Med. Weight
#10021 - Black
#10027 - Yellow
#10028 - Pink
#10029 - Blue
Air Filter Connector
ASSEMBLY OF THE AIR FILTER
You must oil foam filter before use.
Filter will not work if not oiled.
Clean with soap and water only.
You will damage foam if washed if fuel!
#10016
Air Filter
Sponge
Refills
Nylon Strap
( Small )
Nylon Strap
( Small )
40031
Transponder
Holder
3x10mm
Flat Head
Tapping Screw
* Use 4 pcs for
receiver box.
3x10mm
Flat Head
Tapping Screw
* Use 4 pcs for
radio tray.
3 x 10mm
Tapping Screw
#10017 - Blue
#10018 - Yellow
#10019 - Rose
#10034 - Chrome
Foam Air filters Unit
#10013 - Mount Wire
ASSEMBLY OF THE RADIO TRAY
3x10mm
Tapping Screw
3x10mm
Tapping Screw
49039
Alum.
Radio Tray, Orange
Throttle
Servo
3x10
Tapping Screw
Steering
Servo
3x10
Tapping Screw
OPTION:
49044 CNC ALUM. POST,
RADIO TRAY, ORANGE
40027
Radio Tray
Post
( Plastic )
40027
Radio Tray
Post
( Plastic )
3x12mm
Tapping Screw
10274
Servo Post
Servo Post
* Take the servo post
from servo saver plastic
part tree.
94003
3 x 10mm
Tapping Screw..........14
94019
3 x 10mm
Flat Head
Tapping Screw.........8
3X10mm
Tapping Screw
*Connect as per radio.
OPTION:
49017 GRAPHITE RADIO
TRAY.
3 x 5mm Screw
3 X 8mm
Washer
ASSEMBLY OF THE CLUTCH INTO ENGINE
Notes:
Non-Pull Start Engines...
• Alum. Washer behind the flywheel is not needed when using Force engines or similar types. O.S. Engines will require washer spacer.
• To check!..place the brass corn against the engine bearing, then flywheel. You should be covering one or two thread of the engine shaft. If this is the case, you do not need an additional washer behind the flywheel.
You must cut the engine shaft if too long. Count 6 threads in front of the flywheel and mark. This is all you need to tighten the clutch nut and mount the flywheel.
Force Pull Start Engine w/threaded shalf...
• Force Pull Start Engines required NO spacer and no shaft cutting. The engines comes with an alum cast driver washer, you use this part as the spacer, not the alum. washer shown. Also, use the special flywheel brass corn.
This corn fits the thread shaft diameter so you can tighten the flywheel against the drive hub.
30481
3 x 20mm
Hex Screw
30481
3 x 20mm
Hex Screw 3 x 20mm
Cap Screw
3mm Nylon
Locknut
#10398 - 12T
#10399 - 13T
#10400 - 14T (stock)
#10401 - 15T
#10402 - 16T
#10403 - 17T
#10404 - 18T
Clutch Bells
#10102
Clutch Spring
#10010
Clutch Shoes
Black Type
#10330
Brass, Corn
(large hole)
Note
SG Shaft
30481
3 x 20mm
Hex Screw
#34110
5x10x4mm
Ball Bearing
3 x 5mm
Screw
3 x 8mm
Washer
Misc. Hardware
#10099
* Fit the flywheel using a cross wrench or deep socket.
If engine turns when tightening, hold piston with large thick tie-wraps and hard wood in exhaust port.
Do not use metal, it will damage engine.
#34110
5x10x4mm
Ball Bearing
#10098
SG Nut
& Shim KiT
#10091
Clutch Nut screw type
* Shoes are
trailing.
* Place the clutch shoes
with the clutch springs
over the 3 pins of the
flywheel.
Using a screw driver as a lever,
bend the small end of the
clutch spring behind the
clutch nut and press
down to snap shoe in
place.
Option
10799
Flywheel Wrench
#10329
Brass, Corn
(sml hole)
Threaded
Shaft
#10040 (stock)
3 Pin
Flywheel, Taper
#10043
3 Pin
Flywheel, Fan
SEE NOTES
ABOVE
#10048
OR 10049
#30480
Engine Mount
Options
Clutch Spring
10100 - Springs, Polished, Med.
10101 - Spring, Gray, Hard
10102 - Spring, Black, Stock
Clutch Shoes, 3 shoe clutch
10010 - Shoes, Carbon Material, Black
10011 - Shoes, Alum. CNC Blue, Lite Weight
10012 - Shoe, Alum. CNC Purple, Med. Weight
#10021 - Black
#10027 - Yellow
#10028 - Pink
#10029 - Blue
Air Filter Connector
ASSEMBLY OF THE AIR FILTER
You must oil foam filter before use.
Filter will not work if not oiled.
Clean with soap and water only.
You will damage foam if washed if fuel!
#10016
Air Filter
Sponge
Refills
Nylon Strap
( Small )
Nylon Strap
( Small )
40031
Transponder
Holder
3x10mm
Flat Head
Tapping Screw
* Use 4 pcs for
receiver box.
3x10mm
Flat Head
Tapping Screw
* Use 4 pcs for
radio tray.
3 x 10mm
Tapping Screw
#10017 - Blue
#10018 - Yellow
#10019 - Rose
#10034 - Chrome
Foam Air filters Unit
#10013 - Mount Wire
INSTALLATION OF THE FUEL TANK
AND ENGINE ONTO CHASSIS
40066
Pressure
Nipple
3X15mm
Tapping Screw
40109
Fuel Tank, 140+cc
3X15mm
Tapping Screw
Note Book Paper
40066
Fuel Nipple
* Assemble the fuel tank post
before assembling the fuel
nipple.
* Use note book paper to set
gear backlash between spur gear
and clutch bell.
If the space is not correct the spur gear
will be damaged.
3x20mm
Cap Screw
90 Degree
Spur Gear
Clutch Bell
* Loose or tighten 3x20mm cap screw
and 5x10mm hex screw to align
spur gear and clutch bell gear to 90
degree.
38120
Fuel Tank
Post
* Take the fuel tank post
from 40047 plastic parts tree.
3x10mm
Tapping Screw
ASSEMBLY OF THE MANIFOLD AND
MUFFLER
* Read this page very carefully.
3x3mm
Set Screw
40050
Muffler Mounting
Post
40051
Muffler
Wire
4x10mm
Flat Head
Screw
5x5mm or 4x4mm
Set Screw
3x10mm
Tapping Screw
10114
5mm Hex Screw for Engine Mount
#10069
Manifold Adapter
( Red Silicone ) #31991
Manifold, Polished
#10120
Manifold
Spring
#10079
Alum. CNC
Pressure Nipple
#10184
Blue, Silicone
Tube
* Drill a hole (Size 3.5mm)
in the place and align as shown.
Use a two part epoxy glue to
#31992 full seal the nipple base to the nipple.
Dual Chamber, Polished
* Tighten the strip
and cut off the excess.
Option:
10182
Silicone Tube, Red
10183
Silicone Tube, Yel.
10184
Silicone Tube, Blue
ASSEMBLY OF THE FRONT STEERING ROD
* Use the screw provided
with your servo.
10768
Servo Horn
35313
3mm
Nylon Nut
* Enlarge this hole.
3x10mm
Screw
30411
6mm
Ball
30410
6mm
Tie Rod End
30690
3x30mm
Tie Rod
30411
6mm
Ball
3x15mm
Screw
30410
6mm
Tie Rod End
Parallel
16mm
0 10 20 30 40 50 mm
ASSEMBLY OF THE BRAKE LINKAGE
#30800
Brake System Plastic Parts Set
* Cut the shaded
area as shown.
Servo
Mount
2x6mm
Washer
2x4mm
Screw
3x3mm
Set Screw
3x25mm
Screw
36140
2mm
Adjust Mount
Adjust
Mount
2mm
Rod
2mm Rod
2x4mm
Screw
3x3mm set screw
2mm
Tie-Rod
End
2x6mm
Washer
2mm Rod
3x3mm
Set Screw
Plastic Collar
10300
Alum.
Stopper
Throttle
Slider
Throttle
Spring
10300
Alum.
Stopper
30530
Throttle
Ball End
3x10mm
Screw
2mm
Nut
* Align the steering servo as shown.
2x8mm
Screw
10768
Servo Horn, Yel.
* Cut the shaded area
as shown.
INSTALLATION OF THE FUEL TANK
AND ENGINE ONTO CHASSIS
40066
Pressure
Nipple
3X15mm
Tapping Screw
40109
Fuel Tank, 140+cc
3X15mm
Tapping Screw
Note Book Paper
40066
Fuel Nipple
* Assemble the fuel tank post
before assembling the fuel
nipple.
* Use note book paper to set
gear backlash between spur gear
and clutch bell.
If the space is not correct the spur gear
will be damaged.
3x20mm
Cap Screw
90 Degree
Spur Gear
Clutch Bell
* Loose or tighten 3x20mm cap screw
and 5x10mm hex screw to align
spur gear and clutch bell gear to 90
degree.
38120
Fuel Tank
Post
* Take the fuel tank post
from 40047 plastic parts tree.
3x10mm
Tapping Screw
ASSEMBLY OF THE MANIFOLD AND
MUFFLER
* Read this page very carefully.
3x3mm
Set Screw
40050
Muffler Mounting
Post
40051
Muffler
Wire
4x10mm
Flat Head
Screw
5x5mm or 4x4mm
Set Screw
3x10mm
Tapping Screw
10114
5mm Hex Screw for Engine Mount
#10069
Manifold Adapter
( Red Silicone ) #31991
Manifold, Polished
#10120
Manifold
Spring
#10079
Alum. CNC
Pressure Nipple
#10184
Blue, Silicone
Tube
* Drill a hole (Size 3.5mm)
in the place and align as shown.
Use a two part epoxy glue to
#31992 full seal the nipple base to the nipple.
Dual Chamber, Polished
* Tighten the strip
and cut off the excess.
Option:
10182
Silicone Tube, Red
10183
Silicone Tube, Yel.
10184
Silicone Tube, Blue
ASSEMBLY OF THE FRONT STEERING ROD
* Use the screw provided
with your servo.
10768
Servo Horn
35313
3mm
Nylon Nut
* Enlarge this hole.
3x10mm
Screw
30411
6mm
Ball
30410
6mm
Tie Rod End
30690
3x30mm
Tie Rod
30411
6mm
Ball
3x15mm
Screw
30410
6mm
Tie Rod End
Parallel
16mm
0 10 20 30 40 50 mm
ASSEMBLY OF THE BRAKE LINKAGE
#30800
Brake System Plastic Parts Set
* Cut the shaded
area as shown.
Servo
Mount
2x6mm
Washer
2x4mm
Screw
3x3mm
Set Screw
3x25mm
Screw
36140
2mm
Adjust Mount
Adjust
Mount
2mm
Rod
2mm Rod
2x4mm
Screw
3x3mm set screw
2mm
Tie-Rod
End
2x6mm
Washer
2mm Rod
3x3mm
Set Screw
Plastic Collar
10300
Alum.
Stopper
Throttle
Slider
Throttle
Spring
10300
Alum.
Stopper
30530
Throttle
Ball End
3x10mm
Screw
2mm
Nut
* Align the steering servo as shown.
2x8mm
Screw
10768
Servo Horn, Yel.
* Cut the shaded area
as shown.
ASSEMBLY OF THE BRAKE LINKAGE INTO
BRAKE ROD
*use the screw
provided With your radio.
10300
Alum.
Stopper
5mm
Fuel
Tube
3X3mm
Set Screw
*Snap On.
5mm
Fuel
Tube
* Align throttle servo same
as shown.
Brake
Idle
Position
Full Throttle
USING BREAK ADJUST NUT
Tighten
Less Brake
Loosen
Loosen
More Brake
Tighten
* Tighten or loose the adjuster nut
will change the brake.
ALIGN THROTTLE SERVO AND BRAKE SAME AS SHOWN
( Neutral Position )
Engine at idle
( Braking Position )
Brake is not on
Less Brake
More Brake
Loose Tighten
* Tighten or loose the adjuster nut
will change the brake.
Brake is on
Brake Adjust Nut
Engine at full throttle
( Full Throttle Position )
Brake is not on
SHOCK ASSEMBLY
32235
Shock Piston.........4
40059
14.7mm O-Ring....4
32237
1mm Washer.............4
32237
2mm Washer..........4
J-47C
Spring Adjuster....4
49041
Spring
Adjuster,
Orange
40059
14.7mm
O-Ring
Fit the O-ring into groove.
Make a PAIR for front
32237
7mm R-Ring
32237
3.5mm
O-Ring
40076
Shock
Cylinder
32237
2mm
32237
1mm
Washer
Washer
40056
Shock Plastic
Rod End
49041
Spring
Adjuster,
Orange
Make a PAIR for rear
40077
Shock
Cylinder
Oil Seal
* Assembly 2 pieces of the
shock shaft for front and
rear.
40060
2.5mm
Nylon Nut
40054
Short Shaft
32235
Shock
Piston
* Short shaft
for front.
2.6 x 5mm
Washer
40060
2.5mm Nylon Nut........4
40056
Shock Plastic
Rod End
40055
Short Shaft
* Long shaft
for rear.
APPLY OIL TO SHOCK BODY
BEFORE INSTALLING COLLAR
* Be careful not to damage shock shaft.
FILLING THE SHOCKS WITH OIL
1. Pull down piston and pour oil into
shock cylinder. Remove air bubbles
by slowly moving piston up and down.
2. Pull down piston, attach pressure top
and shock oil overflow with tissue
paper.
3. Tighten up shock cap.
OIL
40093
Shock Cap
Hard Coated
*Leave 3mm.
4. Assembly the dust cover.
40058
Shock Shaft
Dust Cover
UP
down.
*Move Slowly.
32033
Pressure Top
* Fit into the groove.
* Cut 6mm for front.
ASSEMBLY OF THE SPRING
OPTION:
40069 - Black, Stock, Spring Set
40070 - Green, Soft Set
40071 - Blue, Med. Set
40072 - White, Hard Set
30411
6mm Ball
40063
Spring Holder
OPTION:
40063 - CNC Alum Spring Holder, Orange
40069
Black
Shock Spring
40052 - Front Shock Set
40053 - Rear Shock Set
* Push 6mm ball joint
into ball end.
ASSEMBLY OF THE BRAKE LINKAGE INTO
BRAKE ROD
*use the screw
provided With your radio.
10300
Alum.
Stopper
5mm
Fuel
Tube
3X3mm
Set Screw
*Snap On.
5mm
Fuel
Tube
* Align throttle servo same
as shown.
Brake
Idle
Position
Full Throttle
USING BREAK ADJUST NUT
Tighten
Less Brake
Loosen
Loosen
More Brake
Tighten
* Tighten or loose the adjuster nut
will change the brake.
ALIGN THROTTLE SERVO AND BRAKE SAME AS SHOWN
( Neutral Position )
Engine at idle
( Braking Position )
Brake is not on
Less Brake
More Brake
Loose Tighten
* Tighten or loose the adjuster nut
will change the brake.
Brake is on
Brake Adjust Nut
Engine at full throttle
( Full Throttle Position )
Brake is not on
SHOCK ASSEMBLY
32235
Shock Piston.........4
40059
14.7mm O-Ring....4
32237
1mm Washer.............4
32237
2mm Washer..........4
J-47C
Spring Adjuster....4
49041
Spring
Adjuster,
Orange
40059
14.7mm
O-Ring
Fit the O-ring into groove.
Make a PAIR for front
32237
7mm R-Ring
32237
3.5mm
O-Ring
40076
Shock
Cylinder
32237
2mm
32237
1mm
Washer
Washer
40056
Shock Plastic
Rod End
49041
Spring
Adjuster,
Orange
Make a PAIR for rear
40077
Shock
Cylinder
Oil Seal
* Assembly 2 pieces of the
shock shaft for front and
rear.
40060
2.5mm
Nylon Nut
40054
Short Shaft
32235
Shock
Piston
* Short shaft
for front.
2.6 x 5mm
Washer
40060
2.5mm Nylon Nut........4
40056
Shock Plastic
Rod End
40055
Short Shaft
* Long shaft
for rear.
APPLY OIL TO SHOCK BODY
BEFORE INSTALLING COLLAR
* Be careful not to damage shock shaft.
FILLING THE SHOCKS WITH OIL
1. Pull down piston and pour oil into
shock cylinder. Remove air bubbles
by slowly moving piston up and down.
2. Pull down piston, attach pressure top
and shock oil overflow with tissue
paper.
3. Tighten up shock cap.
OIL
40093
Shock Cap
Hard Coated
*Leave 3mm.
4. Assembly the dust cover.
40058
Shock Shaft
Dust Cover
UP
down.
*Move Slowly.
32033
Pressure Top
* Fit into the groove.
* Cut 6mm for front.
ASSEMBLY OF THE SPRING
OPTION:
40069 - Black, Stock, Spring Set
40070 - Green, Soft Set
40071 - Blue, Med. Set
40072 - White, Hard Set
30411
6mm Ball
40063
Spring Holder
OPTION:
40063 - CNC Alum Spring Holder, Orange
40069
Black
Shock Spring
40052 - Front Shock Set
40053 - Rear Shock Set
* Push 6mm ball joint
into ball end.
ASSEMBLY OF THE FRONT SHOCK ABSORBER
3x25mm
Cap Screw
Assembly of the right and left hand side are the same.
3 x 20mm
Cap Screw
3x25mm
Cap Screw
ASSEMBLY OF THE REAR SHOCK ABSORBER
* Take the plastic bushing
from the shock plastic
parts tree.
36610
Shock Upper Fixing
Plastic
Bushing
3mm
Nylon Nut
30702
3 x 20mm
Cap Screw..........2
35313
M3
Nylon Nut..........2
90018
3 X 25mm
Cap Screw..........2
36610
Shock Support.....2
Assembly of the right and left hand side are the same.
36610
Shock Upper Fixing
Plastic
Bushing
3mm
Nylon Nut
ASSEMBLY OF THE TIRES AND WHEELS
86062
X Equal Pin
Tire
3 x 20mm
Cap Screw
86035
wheel
INSTANT
GLUE
* Apply instant glue into
the groove of the wheel.
81095
Inner Sponge
ASSEMBLY OF THE WHEELS ONTO
FRONT KNUCKLE ARM AND REAR HUB
Assembly of the right and left hand side are the same.
30051
Wheel Nut
ASSEMBLY OF THE WING
30051
Wheel Nut
* Drill two 7mm holes
for mounting.
25mm
25mm
40084
Wing, Yellow
40083 - Wing White
40084 - Wing Yellow
40085 - Wing Red
40086 - Wing Lime
40087 - Wing White
3x12mm
Screw
40027
Countersunk
Plastic Washer
86044 - Red
86045 - White
86046 - Lime
86047 - Yellow
86048 - Black
86049 - Chrome
17mm Dual Spoke,
2 pairs (4 wheels) per Bag.
OPTION:
49045
CNC Alum. Wing Washer
Orange, 2 pcs.
*Upper Deck Of
The Wing.
25 20 15 10 5
0
5 10 15 20 25
* Check the hole spacing on the underside.
ASSEMBLY OF THE FRONT SHOCK ABSORBER
3x25mm
Cap Screw
Assembly of the right and left hand side are the same.
3 x 20mm
Cap Screw
3x25mm
Cap Screw
ASSEMBLY OF THE REAR SHOCK ABSORBER
* Take the plastic bushing
from the shock plastic
parts tree.
36610
Shock Upper Fixing
Plastic
Bushing
3mm
Nylon Nut
30702
3 x 20mm
Cap Screw..........2
35313
M3
Nylon Nut..........2
90018
3 X 25mm
Cap Screw..........2
36610
Shock Support.....2
Assembly of the right and left hand side are the same.
36610
Shock Upper Fixing
Plastic
Bushing
3mm
Nylon Nut
ASSEMBLY OF THE TIRES AND WHEELS
86062
X Equal Pin
Tire
3 x 20mm
Cap Screw
86035
wheel
INSTANT
GLUE
* Apply instant glue into
the groove of the wheel.
81095
Inner Sponge
ASSEMBLY OF THE WHEELS ONTO
FRONT KNUCKLE ARM AND REAR HUB
Assembly of the right and left hand side are the same.
30051
Wheel Nut
ASSEMBLY OF THE WING
30051
Wheel Nut
* Drill two 7mm holes
for mounting.
25mm
25mm
40084
Wing, Yellow
40083 - Wing White
40084 - Wing Yellow
40085 - Wing Red
40086 - Wing Lime
40087 - Wing White
3x12mm
Screw
40027
Countersunk
Plastic Washer
86044 - Red
86045 - White
86046 - Lime
86047 - Yellow
86048 - Black
86049 - Chrome
17mm Dual Spoke,
2 pairs (4 wheels) per Bag.
OPTION:
49045
CNC Alum. Wing Washer
Orange, 2 pcs.
*Upper Deck Of
The Wing.
25 20 15 10 5
0
5 10 15 20 25
* Check the hole spacing on the underside.
MOUNTING THE BODY
31149
Body Clips
31149
Body Clips
FOR A STICK PACK BATTERY
* Use tape to secure the battery.
40048
Stick Pack
Battery Holder
(5 Cell)
Stick Pack
Battery(5 Cell)
( Not Included.)
Tape
3x12mm
Screw
3x12mm
Screw
40048
Battery Holder
Mount
3x12mm
Screw
3x12mm
Screw
* Insert battery wire into
receiver and connect to
the switch.
40048
Battery Holder
Mount
CHANGING WIDTH FROM 330mm TO ROAR LEGAL 310mm
310mm
330mm
Adjustable width, lower arms.
Simply cut outside 330mm pin holes.
Leave as much plastic as possible
SET-UP GUIDE
RIDE HEIGHT ADJUSTMENT
2mm
Hex Screw
Use a 2mm hex screw to adjust the ride height.
Screwing in the 4x10mm set screw....Ride height becomes lower.
Uncsrewing the 4x10mm set screw..Ride height becomes higher.
Soft
1 2
3
Firm
Soft
1 2
Firm
MOUNTING THE BODY
31149
Body Clips
31149
Body Clips
FOR A STICK PACK BATTERY
* Use tape to secure the battery.
40048
Stick Pack
Battery Holder
(5 Cell)
Stick Pack
Battery(5 Cell)
( Not Included.)
Tape
3x12mm
Screw
3x12mm
Screw
40048
Battery Holder
Mount
3x12mm
Screw
3x12mm
Screw
* Insert battery wire into
receiver and connect to
the switch.
40048
Battery Holder
Mount
CHANGING WIDTH FROM 330mm TO ROAR LEGAL 310mm
310mm
330mm
Adjustable width, lower arms.
Simply cut outside 330mm pin holes.
Leave as much plastic as possible
SET-UP GUIDE
RIDE HEIGHT ADJUSTMENT
2mm
Hex Screw
Use a 2mm hex screw to adjust the ride height.
Screwing in the 4x10mm set screw....Ride height becomes lower.
Uncsrewing the 4x10mm set screw..Ride height becomes higher.
Soft
1 2
3
Firm
Soft
1 2
Firm
ENGINE BREAK-IN AND TUNNING
(BREAK-IN THE ENGINE BEFORE DRIVING THE CAR!)
• Choose a wide clear outdoor location with low dirt and dust.
• Set the car on box or holder with wheels off the ground.
• Turn on radio and car. Make sure throttle is at idle position.
• Fill fuel tank and set master engine needle.
• Prime fuel line and Heat glow plug before pull starting engine.
• When started, let engine fast idle for two tanks of fuel.
OPTIONAL OFNA CAR STANDS
STARTING OF THE ENGINE
How to start the engine:
1. Turn on transmitter and then receiver.
2. Fill fuel tank with fuel bottle.
3. Connect 1.2V glow plug starter.
4. Start engine with 12V starter or starter box
( Note the direction of the starter.)
5. After the engine be started, remove the
1.2V glow plug starter.
* Follow the engine manufacturer instruction manuals
regarding engine set-up, carburetor and maintenance.
1.2V
Glow Plug
Starter
WOOD BLOCK
* To start the engine, use hand held starter motor or starter box.
Rubber wheel turns engine flywheel.
#10250
Starter Box
12V Starter
* Note the direction of the
starter.
Connect with 12V battery
ENGINE BREAK-IN AND TUNNING
(BREAK-IN THE ENGINE BEFORE DRIVING THE CAR!)
• Choose a wide clear outdoor location with low dirt and dust.
• Set the car on box or holder with wheels off the ground.
• Turn on radio and car. Make sure throttle is at idle position.
• Fill fuel tank and set master engine needle.
• Prime fuel line and Heat glow plug before pull starting engine.
• When started, let engine fast idle for two tanks of fuel.
OPTIONAL OFNA CAR STANDS
STARTING OF THE ENGINE
How to start the engine:
1. Turn on transmitter and then receiver.
2. Fill fuel tank with fuel bottle.
3. Connect 1.2V glow plug starter.
4. Start engine with 12V starter or starter box
( Note the direction of the starter.)
5. After the engine be started, remove the
1.2V glow plug starter.
* Follow the engine manufacturer instruction manuals
regarding engine set-up, carburetor and maintenance.
1.2V
Glow Plug
Starter
WOOD BLOCK
* To start the engine, use hand held starter motor or starter box.
Rubber wheel turns engine flywheel.
#10250
Starter Box
12V Starter
* Note the direction of the
starter.
Connect with 12V battery
TUNING AFTER BREAK-IN
Close master needle by turning clockwise until it stops.
Then open needle by turning counterclockwise 3 turns
(rich setting).
Adjust low end needle for best throttle response. Use only small turns. From idle, give it full throttle, if throttle is slow lean out needle until good.
Lean Rich
When running car, adjust carb with 1/8 clockwise turns, slowly leaner, until the top speed good. Check engine temp, if possible, for no more 250 degrees.
Adjust barrel stop so it will not close, accept for a small gap.
This gap will be the idle setting. You will notice the idle will increase with a wide gap.
Idle adjuster screw &
Barrel Stop
APPENDIX PAGES
TUNING AFTER BREAK-IN
Close master needle by turning clockwise until it stops.
Then open needle by turning counterclockwise 3 turns
(rich setting).
Adjust low end needle for best throttle response. Use only small turns. From idle, give it full throttle, if throttle is slow lean out needle until good.
Lean Rich
When running car, adjust carb with 1/8 clockwise turns, slowly leaner, until the top speed good. Check engine temp, if possible, for no more 250 degrees.
Adjust barrel stop so it will not close, accept for a small gap.
This gap will be the idle setting. You will notice the idle will increase with a wide gap.
Idle adjuster screw &
Barrel Stop
APPENDIX PAGES
SHAFT START
NOTICE:
SOME VIOLATOR RTR KITS WILL COME WITH “SHAFT START”
(same as Rotor Start). THEREFORE, A PULL START ENGINE IS NOT
USED AND THE SHAFT START BACK PLATE IS ALREADY
INSTALLED.
BEFORE YOU CAN USE THE SHAFT START MOTOR HANDLE, YOU
MUST FIRST GET OR BUY A STANDARD 7.2 BATTERY PACK.
AFTER POWERING UP THE MOTOR HANDLE, INSERT THE SPECIAL
DOG BONE SHAFT AND TURN OVER THE ENGINE.
CHECK BEFORE STARTING:
1) IS THE FUEL LINE PRIMED?
2) IS THE CARBURETOR SET FOR BREAK-IN SETTINGS?
3) IS THE RADIO ON AND THROTTLE AND BRAKE LINKAGE
CHECKED AND OKAY TO START?
4) MAKE SURE RADIO AND CAR RECEIVER BATTERY ARE ON AND
WORKING WITH GOOD POWER.
5) PLACE THE GLOW HEATER ON PLUG.
6) HOLD THE CAR AND STARTUP THE ENGINE, BY PUMPING
THROTTLE SLIGHTLY. DO NOT HIGH REV ENGINE WHEN IT
STARTS, AT THIS TIME!

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Strong front and rear chassis braces
- Tuned polished dual chamber racing pipe
- Unique adjustable chassis width
- High performance .26 engine with shaft start
- Racing X-Equal tires and V-spoke wheels
- Multi disc brakes with adjustable bias
- Hard coated threaded body oil fill shocks
- 5 Degree hard coated 3mm chassis
- Racing 3 shoe clutch with aluminum CNC flywheel