DDC Instruction Manual

DDC Instruction Manual
Bulletin V-21
Series DDC 17, 35, 53, 70 in-lb Modulating Damper Actuator
Specifications - Installation and Operating Instructions
5-23/32
(145.26)
4-53/64
(122.63)
17/32 SQ
(13.49)
3-25/64
(86.12)
21/32
(16.67)
63/64
(25.00)
2-59/64
1-47/64 (74.22)
(44.05)
9/64
(3.57)
Series DDC Direct Coupled Actuators are non-spring return actuators
that are perfect for positioning of dampers and valves in HVAC Systems.
Actuators are designed to accept 4 to 20 mA or 0 to 10 VDC modulating
control signals and are 24 VAC powered. Actuators produce 17 to 70 inlb (2 to 8 Nm) of torque. Unit features a 0 to 100 VDC feedback signal of
damper position.
Features
• Direct mount.
• Actuator travel indicator.
• Overload protection.
• Manual override.
• Modulating 4 to 20 mA or 0 to 10 VDC control signal.
• Position feedback signal.
• 60,000 cycles nominal.
FUNCTION TESTING
Press the manual button on the back of the actuator. The gearing inside
the actuator will break away. The damper can be operated manually
while pressing the manual button. DO NOT OPERATE WHEN POWER
IS ON!
DWYER INSTRUMENTS, INC.
P.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A.
SPECIFICATIONS
Power Requirements: 24 VAC, ±10%, 50/60 Hz, single phase.
Power Consumption: 4 VA.
Control Input: 4-20 mA or 0-10 VDC.
Overload Protection: Magnetic clutch.
Angle of Rotation: 95° (mechanically adjustable).
Accuracy: ±5%.
Fits Shaft Diameter: 0.4˝ (10 mm) or 0.5˝ (13 mm).
Position Indication: Visual indicator.
Direction of rotation: CW/CCW.
Running Time: 17 in-lb, 35 in-lb, 53 in-lb: 72 sec.; 70 in-lb:160 sec.
Electrical Connection: Terminal block, 18 AWG.
Manual Override: Push button.
Temperature Limit: -22 to 122°F (-30 to 50°C).
Sound: <45 dB.
Life Expectancy: 60000 full cycles.
Housing: NEMA 2 (IP40).
Wiring Connection: Terminal block.
Standard Accessories: (2) imitative baffles, (2) baffle setscrews, (1)
actuator body setscrew, and (1) aluminum gasket.
Weight: 1.72 lb (0.78 kg).
Phone: 219/879-8000
Fax: 219/872-9057
www.dwyer-inst.com
e-mail: [email protected]
WIRING DIAGRAM
CHART 1: ACTUATOR ACTION
Set Up
• Set jumper J1 or J2 to proper selection for reverse or direct acting. See
Chart 1: Actuator Action above for more detail.
• Set jumper J3 for Voltage or Current input control signal.
• Set jumper J4 for actuator direction on loss of control signal.
• Potentiometer PT1 adjusts the stroke of the actuator.
MAINTENANCE
Upon final installation of the Series DDC Non-Spring Return Direct
Coupled Actuator, no routine maintenance is required. A periodic check
of the system calibration is recommended. The Series DDC is not field
serviceable and should be returned if repair is needed (field repair
should not be attempted and may void warranty). Be sure to include a
brief description of the problem plus any relevant application notes.
Contact customer service to receive a return good authorization number
before shipping.
Square shaft installation
Before installation, the aluminum gasket should be put into the hole of
Output Axle. Fix with square damper shaft. The rotating angle of the
actuator can be set by internal potentiometer. The match between
working range and feedback signal is automatically done by the actuator.
a = .4˝ (10 mm)
or
.5˝ (13 mm)
©Copyright 2014 Dwyer Instruments, Inc.
DWYER INSTRUMENTS, INC.
P.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A.
Printed in U.S.A. 5/14
Phone: 219/879-8000
Fax: 219/872-9057
FR# R3-443451-40 Rev. 2
www.dwyer-inst.com
e-mail: [email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement