BBQ Grillware GSF2616 Bbq And Gas Grill Owner's Manual

ITEM # 41590
3-Burner LP Gas Grill
WARNING
Improper installation,
adjustment, alteration, service or
maintenance can cause injury or
property damage.
Read the installation,
operation and maintenance
instructions thoroughly before
installing or servicing this
equipment.
DANGER
Failure to follow these
instructions could result in fire
or explosion that could cause
property damage, personal
injury or death.
DANGER
DO NOT use gas grill for indoor
cooking or heating. TOXIC
fumes can accumulate and
cause asphyxiation. DO NOT
use in or on boats or
recreational vehicles.
PROP 65 WARNING
Chemicals known to the state of
California to cause cancer, birth
defects or other reproductive
harm are created by the
combustion of propane.
WARNING
For Outdoor Use Only
(Outside any enclosure)
GSF2616
Owner’s Manual
SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. IF YOU ARE ASSEMBLING THIS UNIT
FOR SOMEONE ELSE, GIVE THIS MANUAL TO HIM OR
HER TO SAVE FOR FUTURE REFERENCE.
FOR CUSTOMER SERVICE, EMAIL TO
[email protected] OR
CALL 1-877-885-8227,
6 A.M. – 5 P.M.(PST),MONDAY-FRIDAY.
FURTHER INFORMATION PLEASE VISIT OUR WEBSITE
AT WWW.PYROMAGICBBQ.COM
0
Grill Operation 1-2-3
Before Grilling,
Step 1
Step 2
Step 3
Keep your grill a safe distance away from your property.*
Always Perform a Leak Test. *
Keep children away from the grill.
During Grilling,
(To avoid tripping safety valves, please follow these instructions carefully!)
Step 1
Step 2
Step 3
First open lid and turn gas valve on slowly.
Turn only one knob on at a time when lighting up the grill.
Use protective gloves when grill gets hot.
After Grilling,
Step 1
Step 2
Step 3
Burn grill for 10-15 minutes to burn off food residues.
Wait until the grill is completely cooled before closing lid.
Clean up grease build-up and cover your grill.
* Please refer to the owner’s manual for details.
WARNING
FOR YOUR SAFETY
1. DO NOT store or use gasoline or other
flammable vapors and liquids within
25 feet of this or any other appliance.
2.
When cooking with oil/grease, do
not allow the oil/grease to exceed
350°F (177°C). Do not store or use
extra cooking oil in the vicinity of this
or any other appliance.
An LP cylinder not connected for use
3.
should NOT be stored within 10 feet
of this or any other appliance.
WARNING
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flames.
3. Open lid.
4. If odor continues,
immediately call your gas
supplier or fire department.
Always read and understand the WARNINGS and INSTRUCTIONS that are contained in this manual
before attempting to use this gas barbecue grill, to prevent possible bodily injury or property damage.
Always keep this manual in or near the grill, for convenient future reference.
GSF2616
Owner’s Manual
1
Table of Contents
For Your Safety.................................................................................................3
Illustrated Parts List .........................................................................................5
Hardware List.....................................................................................................6
Assembly Instructions.......................................................................................7
Operating Your Grill.........................................................................................15
LP Gas Supply Connection..............................15
Checking for Leaks...........................................16
Lighting Your Grill.............................................16
Excess Flow Safety Valve Reset Procedure....17
Care and Maintenance.......................................18
Award-Winning Barbecue Recipes.................................................................20
Troubleshooting................................................................................................21
Warranty Program............................................................................................22
GSF2616
Owner’s Manual
2
For Your Safety
Dear
Valued Customer,
Congratulations on your new barbecue grill purchase! You’ve made the right choice. In this manual, you will find
assembly instructions, suggestions for grilling and helpful hints, as well as guidelines for the safe operation, proper care
and use of your grill. Our expert staff strives to provide you with an easy to assemble product. Should you have any
questions or problems with this product, please email to [email protected] or call our customer service
department at 1-877-885-8227
6:00 am - 5:00 pm (PST), Monday through Friday. Further information please visit our website at www.pyromagicbbq.com
NOTE: The use and installation of this product must conform to local codes. In the absence of local codes, use the
National Fuel Gas Code, ANSI Z223.1/ NFPA54.
IMPORTANT NOTICE: READ ALL INSTRUCTIONS PRIOR TO ASSEMBLY AND USE
Safety First!
Read and understand all warnings and precautions prior to operating your grill.
WARNING
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12
13.
14.
15.
16.
17.
18.
This grill is for outside use only. It should not be used in a building, garage or any other enclosed area.
The use of alcohol, prescription or non-prescription drugs may impair an individual’s ability to properly
assemble or safely operate this appliance.
Always open the grill lid carefully and slowly as heat and steam trapped within the grill could cause severe burns.
Always place your grill on a hard and level surface far away from combustible materials and structures. An asphalt or
blacktop surface may not be acceptable for this purpose.
Do not leave a lit grill unattended.
Keep children and pets away from the grill at all times.
This is not a tabletop grill. Do not place this grill on any type of tabletop surface.
Do not use the grill in high winds.
This grill must be use with propane gas only (propane gas cylinder not included).
Do not attempt to attach this grill to the self-contained propane system of a camper, trailer, motor home or house.
Do not use charcoal or lighter fluid.
Do not use gasoline, kerosene or alcohol for lighting. The LP-gas supply cylinder must be constructed and marked
in accordance with the specifications for propane gas cylinders of the U.S. Department of Transportation (DOT)
CFR 49.
This outdoor gas appliance is not intended to be installed in or on recreation vehicles and/or boats.
Do not attempt to move the grill while it is lit.
Do not use the grill unless it is COMPLETELY assembled and all parts are securely fastened and tightened.
Keep combustible items and surfaces at least 24 inches away from the grill at all times. DO NOT use this gas grill or any
gas product under any overhead enclosure or near any unprotected combustible constructions.
Do not use in an explosive atmosphere. Keep grill area clear and free from combustible materials,
gasoline and other flammable vapors and liquids.
Do not attempt to use or assemble with missing or damaged parts. Contact customer service for a replacement.
CAUTION-Prevention of Burns
1. To avoid burns, do not touch metal parts of the grill until they have completely cooled for at least 45 minutes or
unless you are wearing protective gear such as pot holders, gloves, BBQ mittens, etc.
2. Do not alter the grill in any manner.
3. Clean and inspect the hose before each use. If there is evidence of abrasion, wear, cuts or leaks, the hose must be
replaced prior to operation. The replacement hose assembly should be in accordance with the manufacturer’s
specifications.
4. Move gas hoses as far away as possible from hot surfaces and dripping hot grease.
5. Never keep a filled gas container in a hot car or car trunk. Heat will cause the gas pressure to increase, which
could open the relief valve and allow gas to escape.
GSF2616
Owner’s Manual
3
Safe Locations For Use Of This Outdoor Grill
DANGER
Never use this outdoor grill inside any building, garage, shed or breezeway, or inside any boat, trailer or recreationall vehicle,
to prevent a possible fire and to prevent the possibility of carbon monoxide poisoning or asphyxiation.
WARNINGS
Do not use this appliance under overhead combustible surface or covered area (e.g., awnings, umbrellas, porches or
gazeboes).
Always confirm that this grill is not positioned under the overhang of a house, a garage or other structure before lighting it.
An overhang will serve to deflect flare-ups and radiated heat into the structure itself, which could result in a fire.
Always confirm that this grill is positioned more than 24 inches (61 cm)
away from any combustible materials or surface before lighting it, and that
no gasoline or other volatile substances are store in the vicinity of this grill.
(As the fig. shown on right).
24 Inches
24 Inches
The temperature of a grease fire or of the radiated heat might otherwise
be sufficient to ignite nearby combustible or volatile substances.
Always locate this grill where there will be ample combustion and
ventilation air, but never position it in the direct path of a strong wind.
Never allow the grill to operate while unattended, to prevent uncontrolled grease fires from erupting.
Never attempt to move this grill while it is in operation or while it is still hot, to prevent possible personal injury.
Never store or use gasoline or other flammable or volatile substances in the vicinity of this grill or in the vicinity of any other
heating-generating appliance, because of the danger of starting a fire.
Always confirm that the installation of this grill conforms with the requirements of all local codes or, in the absence of
applicable local codes, with either the National Fuel Gas Code, ANSI Z223. NFPA 54 or CAN/CGA-B149.2, Propane
Installation Code.
DANGER – Gas Safety
Liquid propane (LP) gas is flammable and hazardous if handled improperly. Become aware of its
characteristics before using any propane product.
• Propane Characteristics: Flammable, explosive under pressure, heavier than air and settles in pools in low areas.
• In its natural state, propane has no odor. For your safety, an odorant has been added.
• Contact with propane could cause freeze burns to the skin.
• This grill is shipped from the factory for propane gas use only.
• Never use a propane cylinder with a damaged body, valve, collar or footing.
• Dented or rusted propane cylinders may be hazardous and should be checked by your propane gas supplier.
CAUTION
ƒ
It is essential to keep the grill’s valve compartment, burners and circulating air passages clean.
ƒ
Inspect the grill before each use.
GENERAL INFORMATION
1. A propane gas cylinder is required for operation.
2. This gas grill is NOT intended for commercial use.
GSF2616
Owner’s Manual
4
Illustrated Parts List
1. Leg R-F ----------------------------1pc
2. Leg L-F ---------------------------1pc
3ˊLeg L-B --------------------------1pc
4ˊLeg R-B ----------------------1pc
5. Right Foot------------------------1pc
6. Left Foot-------------------------1pc
7. Wheel---------------------------2 pcs
8. Axle----------------------------- 1pc
9.Cart Front Panel--------------1pc
10. Top Cart L-F----------------------1pc
11. Top Cart L-B----------------1pc
12. Top Cart R-F ------------------1pc
13. Top Cart R-B ------------------1pc
14. Control Panel ---------------------1pc
15. Cart Beam-----------------2pcs
16. Back Beam--------------------1pc
17. Tank Hook---------------------1pc
18. Grill Body Assembly-------------1pc
19. Right Side Shelf------------1pc
20. Left Side Shelf----------------1pc
21. Side Burner Grate ------------1pc
22. Heat Plate------------------------3pcs
23. Cooking Grid-------------2pcs
24. Warming Rack-Body--------1pc
25. Warming Rack- Lid----------1pc
26. Cup Support---------------------1pc
27. Grease Cup----------------1pc
GSF2616
Owner’s Manual
5
Hardware List
29pcs
A
C
E
M6 X 16mm Bolt
(2pcs spare
included)
B
Side Burner Knob
1pc
D
1pc
F
Wrench
2pcs
H
Collar
Phillips Head
Screwdriver
G
M10 Washer
Hardware listed above is not scaled to exact size
(A screwdriver is included for your convenience.)
GSF2616
Owner’s Manual
6
2pcs
M4 X 10mm Bolt
Axle Nut
2pcs
2pcs
1pc
Assembly Instructions
Remove all contents from the carton packaging. Make sure all parts are present before attempting assembly. Once the grill is
fully assembled, go back check and make certain all the bolts are tighten. Tighten again by the screwdriver provided if it is
necessary.
Estimated Assembly Time: It will takes less than 40 minutes to assembly the grill
9 Step 1
Align the holes at the cart front panel (9) with the
holes on the leg R-F (1).
Screw a M6x16mm bolt (A) into each pre-drilled
hole and tighten by hand until secure.
Repeat the procedure for the leg L-F(2).
Go back and tighten by the screwdriver provided.
$ x4 Step 2
Align the holes on the right foot (5) with the holes
on the leg R-F(1) and the leg R-B (4) respectively .
Screw a M6x16mm bolt (A) into each pre-drilled
hole and tighten by hand until secure.
Align the holes on the left foot (6) with the holes on
the leg L-F(2) and the leg L-B (3) respectively .
Screw a M6x16mm bolt (A) into each pre-drilled
hole and tighten by hand until secure.
Go back and tighten by the screwdriver provided.
GSF2616
Owner’s Manual
7
Step 3
3
Align the holes on the top cart R-F(12) with
the holes on the leg R-F(1). Screw a
M6x16mm bolt (A) into a pre-drilled hole.
Align the holes on the top cart R-B (13) with
the holes on the leg R-B (4). Screw a
M6x16mm bolt (A) into a pre-drilled hole.
Align the holes on top cart L-F(10) with the
holes leg L-F(2). Screw a M6x16mm bolt (A)
into a pre-drilled hole.
Align the holes on the top cart L-B (11) with
the holes on leg L-B (3), Screw a M6x16mm
bolt (A) into a pre-drilled hole.
Tighten all bolts by hand until secure.
Go back and tighten by the screwdriver
provided.
1
0
$
Step 4
Align the hole on control panel (14) with a
hole on the top cart R-F(12). Screw a
M6x16mm bolt (A) into a pre-drilled hole.
Align the hole on control panel (14) with a
hole on top cart L-F(10). Screw a M6x16mm
bolt (A) into a pre-drilled hole.
Tighten by hand until secure.
Go back and tighten by the screwdriver
provided.
GSF2616
Owner’s Manual
8
4
Step 5
Align the holes on back beam (16) with the holes
on leg L-B (3). Screw a M6x16mm bolt (A) into
each pre-drilled hole.
Align the holes on back beam (16) with the holes
on leg R-B (4), screwing a M6x16mm bolt (A) into
each pre-drilled hole.
Tighten all bolts by hand until secure.
Go back and tighten by the screwdriver provided.
6
$ x4 19
Step 6
Align the pre-assembled adjustable screw on the left
side shelf (20) with the holes on the top cart L-F(10) and
the top cart L-B (11) respectively.
Move the left side shelf to the direction of the narrow end
of the holes on the top cart L-F and top cart L-B.
Tighten the pre-assembled adjustable screw.
Repeat the same procedure for the right side shelf (19).
Tighten all bolts by hand until secure.
Go back and tighten by the screwdriver provided
GSF2616
Owner’s Manual
9
20
Step 7
Insert the axle (8) into the hole of the right
foot.
Put a wheel (7) and a M10 (G) washer on each
end of the axle.
NOTE: protruding side of each wheel must
face the surface of grill leg.
Tighten each axle nut (D) toward the wheel,
make certain each axle nut should be flat
with each end of axle.
Nut should be flat with end of whee
axle. Do not over tighten the nut.
'
G
G
'
Protruding side of wheel should face
grill leg.
$ (x4 Step 8
Put grill body assembly (18) upon cart assembly.
Align the holes on both side of grill body with the
holes on both side cart, make certain stainless steel
face panel flat ends fully insert into each hole in the
control panel.
Screw a M6x16mm bolt (A) into each pre-drilled hole.
Tighten by screwdriver until secure.
Tighten the bolts by the screwdriver provided.
GSF2616
Owner’s Manual
10
18
Step 9
Align the holes on the cart beam (15) with the
holes on the left cart
Screw a M6x16mm bolt (A) into each pre-drilled
hole and tighten by hand until secure.
Repeat the procedure for the right cart.
Go back and tighten by the screwdriver
provided.
$ X8 5
5
Step 10
Align the hole on tank hook (17) with the holes on
the right cart beam.
Screw a M6x16mm bolt (A) into the pre-drilled hole.
Tighten the bolt by the screwdriver provided.
$
7
GSF2616
Owner’s Manual
11
&
%
Step 11
Open the side burner lid. Insert side burner valve into the
venture tube on the side burner..
Align the holes on side burner valve with the holes on
the side burner knob seat.
Screw a M4x10mm bolt (B) into each pre-drilled hole.
Tighten the bolts by the screwdriver provide.
Insert the side burner knob (C) into side valve shaft.
Connect the ignition cable with the electrode.
Make certain the connection is secure.
.
1
Step 12
Place the heat plates (22) on top of the burners in
the grill.
Place the cooking grids (23) on the grill surface.
Open the side burner lid, and place the side burner
grate (21) on top of the side burner.
2
GSF2616
Owner’s Manual
12
5
4
Step 13
Insert the warming rack–lid (25) on the hook
on the both side of the grill lid.
Put the warming rack-body (24) on top of the
grill body above the cooking grids.
Make certain the two racks are on a secure
position.
Step 14
Hook both ends of the cup support (26) on the
holes of the grease pan.
Place the grease cup (27) on the cup support.
7
GSF2616
Owner’s Manual
13
6
Step 15
Screw the regulator with gas hose
into cylinder valve. ( Gas cylinder not included ).
Make certain the regulator is
connected secure.
*Refer to LP Gas Supply Connection in
the manual for important safety
information.
Collar (H)
Rotisserie Shaft
Stopper
(With Rotisserie set)
Step 16
Collar (H) In Hardware Pack Assembly.
(When operating with rotisserie set)
(1): Insert the collar (H) into rotisserie shaft.
(2): Place the collar on the groove of the
left side wall of grill body.
(3): Push the stopper to contact with the
collar and tighten the set screw.
GSF2616
Owner’s Manual
14
Set Screw
(With Rotisserie set)
Fully Assembled View
Operating Your Grill
CAUTION:
Use only the regulator provided. If a replacement is necessary, call our customer service center. The use of
unauthorized parts can create an unsafe condition and environment.
The propane gas supply cylinder used must be constructed and marked in accordance with the Specifications for Propane Gas
Cylinders of the U.S. Department of Transportation (DOT). Only cylinders with a listed overfill prevention device (OPD) and
marked “propane” may be used. Cylinders with an OPD will have valve handles with three “lobes” (prongs).
The pressure regulator and hose assembly supplied with the outdoor cooking gas appliance must be used. Replacement pressure
regulators and hose assembly must be those specified by the outdoor cooking gas appliance manufacturer. Only use 20 pound
cylinders equipped with a cylinder connection device compatible with the connection for outdoor cooking appliances. The
cylinder must include a collar to protect the cylinder valve. The gas cylinder should not be dropped or handled roughly. If the
appliance is not in use, the gas cylinder must be disconnected.
Storage of the appliance indoors is permissible ONLY if the cylinder is disconnected and removed from the appliance. Cylinders
must be stored outdoors and out of the reach of children. Cylinder must not be stored in a building, garage or other enclosed
area. Your cylinder must never be stored where temperatures can reach over 125F.
Before connecting, make sure there is no debris caught in the head of the gas cylinder, regulator valve or in the head of the
burner and burner ports. Connect regulator valve and hand tighten firmly. Disconnect the propane cylinder from the regulator
valve when the grill is not in use. DO NOT obstruct the flow of combustion air or ventilation air to the grill. The propane cylinder
must be arranged for vapor withdrawal and equipped with a listed overfill prevention device (OPD).
Danger: A fire causing death or serious injury may occur if the following is no followed exactly:
Never store or use gasoline or other volatile substance in the vicinity of this grill.
Never store a spare propane cylinder in the vicinity of this grill, or in the vicinity of another
potential heat source.
Never fill the propane cylinder beyond 80% full.
GSF2616
Owner’s Manual
15
LP (Propane) Gas Supply Connection
1. Always place the propane cylinder on the tank brackets located on the right side of the cart.
2. Always confirm that all burner control knobs are in the OFF position before activating the gas supply.
3. Before connection, be sure that there is no debris caught in the head of the gas cylinder, head of the regulator valve, or in
the head of the burner and burner ports.
4. Always connect the gas supply regulators as follows:
Insert the nipple of the valve coupling into the tank valve and tighten the connection
collar by turning it clockwise with one hand while holding the regulator with the other.
(As the fig. shown on right)
5. Disconnect the propane cylinder from the regulator valve when the grill is not in use.
6. Do not obstruct the flow of combustion air and ventilation air to the grill.
DANGER
To prevent fire or explosion hazard when testing for a leak:
1. Always perform the “leak test “on page 16 before lighting the grill and each time the
cylinder is connected for use.
2. Do not smoke or allow other sources of ignition in the area while conducting a leak test.
3. Conduct the leak test outdoors in a well-ventilated area.
4. Do not use matches, lighters or a flame to check for leaks.
5. Do not use grill until all leaks have been sopped, if you are unable to stop a leak, disconnect the propane supply, call for gas
appliance service or your local propane gas supplier.
Checking for Leaks
1. Make a 2-3 oz. of leak solution by mixing one part liquid dishwashing soap with three parts water.
2. Make sure control knobs are in the “OFF” position.
3. Spray some solution on the tank valve up to the regulator connection.
(As the fig. shown on right).
4. Inspect the solution at the connections, looking for bubbles. If no bubbles appear,
the connection is secure.
.
5. If bubbles appear, you have a leak. Go to step 6.
6. Disconnect the regulator from the tank and reconnect, make sure the connection is secure.
7. Retest with solution.
8. If you continue to see bubbles, replace the cylinder.
Lighting Your Grill
Danger: Failure to open lid while igniting the barbecue’s burners or not waiting 5 minutes to allow gas to clear if the barbecue
does not light ,may result in an explosion, which could cause serious bodily injury or death.
WARNING: Never stand with your head directly over the grill when preparing to light the main burners, to prevent possible bodily
injury.
Main Burner
1. Open lid while lighting burners.
WARNING: Attempting to light the burner with the lid closed may cause an explosion. Make sure there are no obstructions of
airflow to the gas unit. Spiders and insects can nest and clog the burner/venturi tube at the orifice. A clogged burner tube can
lead to a fire beneath the appliance.
2. All valves must be in the “OFF” position.
3. Open cylinder valve.
4. Ignite only the burners you wish to use, using the same method for each:
Push desired burner valve knob and rotate slowly about 1/4 counter-clockwise until a click is heard. The burner should
light. If the burner does not light, return the valve knob to the “OFF” position immediately. Wait five minutes for the gas
to clear and repeat the procedure. After burner is lit, repeat the procedure with any other burner desired.
5. Adjust valve knob(s) to desired cooking temperature.
GSF2616
Owner’s Manual
16
Using the Lighting Stick to Light the Main Burners
1. Remove the cooking grid from the burner you wish to light.
2. Insert a match into the end of lighting stick. Light the match.
3. Once lit, place the flame through the hole on grill body to reach the burner ports.
(As the fig. shown on right side).
4. Press the valve knob and rotate it counter clockwise to the ‘’HIGH’’ position. The
burner should light immediately. To light up other burners, repeat the same procedure
for the adjacent burner and continue in sequence until all desired burners are lit.
5. Replace cooking grid and adjust burners to the desired cooking temperature.
Precautions
1.
After lighting, please observe the burner flame. Make sure all burner ports are lit.
2.
If the burner flame goes out during operation, immediately turn the gas “OFF”. Open lid to let the gas clear for at least
5 minutes before re-lighting.
3.
Before cooking on the grill for the first time, operate the grill for approximately 15 minutes with the lid closed and the gas
turned on “HIGH”. This will “heat clean” the internal parts, dissipate odor from the manufacturing process and painted finish.
4.
Clean the grill after each use. DO NOT use abrasive or flammable cleaners. this may damage parts of the grill and cause a
fire.
Side Burner
1. Open lid while lighting the burner. Lid must remain open while burner is lit.
2. Valve must be in the “OFF” position.
3. Open cylinder valve.
4. Push side burner knob fully and rotate it slowly about 1/4 counter-clockwise until a click is heard. The burner should light. If
the burner does not light, turn the knob to the “OFF” position immediately. Wait five minutes for the gas to clear and repeat
the procedure.
5. Adjust valve knob to the desired cooking temperature
2 in.
1 in.
0 in.
Observe flame height when lit:
Flame should be a blue/yellow color between 1 to 2 inches high.
Confirm that the burner is properly lit and that the flame pattern is as desired,(see fig. A,B and C below for the proper flame
patterns ).If the flame pattern is other than normal, consult the troubleshooting guide on page 21 for corrective action.
FIG. A
Normal: Soft blue flames with yellow tips
between I inch - 2 inches high.
GSF2616
Owner’s Manual
FIG. B
FIG. C
Out of adjustment: Noisy hard blue
flames – too much air.
17
Poor combustion: Wavy, yellow
flames- too little air.
Excess Flow Safety Valve Reset Procedure
The new regulators are equipped with a safety device that restricts the gas flow in the event of a gas leak. However, unsafe
practices of grill operation could activate the safety device without having a gas leak.
A sudden shut off of the gas flow typically occurs if you open the LP tank valve rapidly, or if one or more of the burner control knobs
is in an open position when opening the LP tank valve.
This procedure is effective with all LP Tank sizes as well as Natural Gas. When performing the procedure on a Natural Gas model,
simply substitute "Natural Gas valve" for "LP Tank".
To ensure the procedure is safely and is successfully performed, please carefully follow the instructions below.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Close the LP tank valve.
Turn all burner control knobs to the OFF position.
Disconnect the regulator from the LP tank.
Open the lid of the grill.
Turn burner control knobs to HIGH.
Wait at least 1 minute.
Turn burner control knobs OFF.
Wait for at least 5 minutes.
Re-connect the regulator to the LP tank.
SLOWLY turn the LP tank valve at ¼ turn at a time and have the valve all the way open.
With the lid open, For BBQ with ignition button: ONLY turn on ONE front burner control knob to the HIGH position. Ignite
the grill by pushing the ignition button. For BBQ with an automatic ignition: Push down the control knob you want to light,
turn counter clock wise until you hear the ignition click.
After the first front burner is lit, turn on the other control knob(s) to the HIGH position. **If you have more than two burners,
ONLY turn them on ONE AT A TIME.
When all front burners are lit, close the BBQ lid
Wait for 10-15 minutes, the temperature should reach 400 – 450 F°
Flare-ups
“Flare-ups” sometimes occur when food drippings fall onto the hot heat distribution plate or burners and ignite. Some flaring is
normal and desirable, as it helps impart the unique flavors associated with grilled foods. Controlling the intensity of the flare-ups is
necessary, however, in order to avoid burned or unevenly cooked foods and to prevent the possibility of accidental fire.
WARNING: Always monitor the grill closely when cooking and turn the flame level down (LOW) of OFF, if flare-ups
intensify
Shutting Off Burners
1. Always turn the valve knob(s) clockwise to the ‘’HIGH’’ position, then press and turn it to ‘’OFF’’. Never force the knob without
pressing it. This could damage the valve.
2. Promptly turn the gas supply to the “OFF” position at the propane cylinder.
3. Close the lid of the grill.
IMPORTANT
Always allow to completely cool off before covering your grill to prevent corrosion from condensation
Care and Maintenance
Caution: All cleaning and maintenance should be done when the grill is cool, with the fuel supply turned off at the control dial and
the propane cylinder disconnected. DO NOT clean any grill part in a self-cleaning oven. The extreme heat will damage the finish.
Cleaning
Burning off the grill after every use (approx. 15 minutes) will keep excessive food residue from building up.
GSF2616
Owner’s Manual
18
Recommended cleaning materials Mild dishwashing liquid detergent
Hot water
Nylon cleaning pad
Wire brush
Paper clip
Putty knife/scraper
Compressed air
DO NOT use cleaners that contain acid, mineral spirits or xylene.
Outside surfaces
Use a mild dishwashing detergent and hot water solution to clean. Rinse thoroughly with water.
Inside surface
If the inside surface of the grill lid has the appearance of peeling paint, baked on grease has turned to carbon and is flaking off.
Clean thoroughly with a strong solution of detergent and hot water. Rinse with water and allow it to completely dry.
Interior of grill bottom – Remove residue using brush, scraper and/or cleaning pad. Wash with a dishwashing detergent and hot
water solution. Rinse with water and let dry.
Cooking Grids – The porcelain grates have a glass-like composition that should be handled with care. Use a mild dishwashing
detergent or baking soda and hot water solution. Non-abrasive scouring powder can be used on stubborn stains. Rinse with
water.
Heat Plates – Clean residue with wire brush and wash with soapy water. Rinse with water.
Grease Cup – Periodically empty the grease cup and clean with a dishwashing detergent and hot water solution.
Cleaning the Burner Assembly
1.
2.
3.
4.
5.
6.
7.
8.
9.
Turn gas off at the control knobs and propane tank.
Remove cooking grids and heat plate.
Remove grease cup.
Remove burner by unscrewing nut from beneath burner “foot” using a screwdriver and pliers.
Lift burner up and away from the gas valve orifice.
Clean inlet (venturi) of burner with small bottle brush or compressed air.
Remove all food residue and dirt on outside of burner surface.
Clean any clogged ports with a stiff wire (such as an opened paper clip).
Inspect burner for damage (cracks or holes). If damage is found, replace with a new burner. Reinstall burner. Check to
ensure the gas valve orifices are correctly positioned, pointing straight into burner inlet (venturi). Also, check position of
spark electrode.
GSF2616
Owner’s Manual
19
Award-Winning Barbecue Recipes
Never-fail Barbecue Sauce
Ingredients:
¼ cup
Finely chopped onion
2 tablespoons
Butter or margarine
¼ cup
Brown sugar, firmly packed
1 tablespoon
Worcestershire sauce
¼ teaspoon
Hot sauce
Garlic clove, finely chopped
1
1 cup
Catsup
¼ cup
Lemon juice
Prepared mustard
1 teaspoon
Prepare:
Cook onion and garlic in margarine until tender. Add
remaining ingredients and bring to a boil. Simmer
uncovered 15 to 20 minutes. Refrigerate leftovers
after use.
Mamma’s Marinated Chicken
Ingredients:
¼ cup
Dijon mustard
2 tablespoons
Fresh lemon juice
1 ½ teaspoons
Worcestershire sauce
½ teaspoon
Dried tarragon
Freshly ground black pepper
¼ teaspoon
4
Boneless, skinless chicken
breast halve
Prepare:
Combine ingredients, mixing well. Marinade chicken
for several hours. Grill uncovered, over medium heat,
for 10 to 15 minutes. Chicken is done when juices run
clear.
Barbecued Honey Steak
Ingredients:
5 pounds
Beef sirloin steak
2 tablespoons
Red pepper -- crushed
1 teaspoon
Black pepper
2
Garlic cloves -- crushed
1 large
Onion
1 cup
Honey
Prepare:
Combine all ingredients and marinate steak for 7-8
hours. Remove meat from marinade and grill over
very high heat to desired doneness. Heat leftover
marinade to a boil and pour over grilled steak to
serve.
GSF2616
Owner’s Manual
Hardcore Grilled Trout
Ingredients:
¼ cup
Lemon or lime juice
2 tablespoons
Melted butter
2 tablespoons
Vegetable oil
2 tablespoons
Chopped parsley
1 tablespoon
Hot sauce
Ground ginger
½ teaspoon
½ teaspoon
Salt
4 brook trout -- about 1 pound each
Prepare:
Combine lemon juice, margarine, oil, parsley, hot
sauce, ginger and salt. Mix well. Pierce skin of fish
in several places. Roll fish in juice mixture to coat
inside and out. Cover and refrigerate 30 minutes to
1 hour, turning occasionally. Remove fish from
marinade. Place fish on grill; brush fish with
marinade while grilling. Cook over high heat for 5
minutes. Turn and brush with marinade. Cook 5
minutes longer. Fish is done when it flakes easily
with fork.
Grilled Veggies
Ingredients:
¾ cup
Olive oil
¼ cup
Red wine vinegar
1 teaspoon
Fresh rosemary
1 teaspoon
Fresh thyme leaves
1 teaspoon
Fresh basil, chopped
Fresh oregano, chopped
1 teaspoon
1 tablespoon
Minced garlic
½ teaspoon
Salt
½ teaspoon
Ground black pepper
2 pounds assorted vegetables, chopped or whole
according to taste.
Prepare
Combine all ingredients in a small bowl. Marinade
vegetables with sauce. Cover and refrigerate for 2
hrs. Grill vegetables over medium heat until tender,
brushing them with marinade while they cook.
Cooking times will vary according to the vegetables
chosen.
20
Troubleshooting
Problem
Possible Cause
Solution
Burner will not light using
knobs.
Wires or electrode covered
with cooking residue.
Clean wire and/or electrode
with rubbing alcohol.
Electrode and burners are wet.
Wipe dry with cloth.
Electrode cracked or
its sparks at the crack.
Replace electrode.
Wire is loosen or disconnected.
Reconnect wire or replace
electrode/wire assembly.
Burner will not light with
match.
No gas flow.
Call your natural gas company
Obstruction of gas flow.
Clear burner tubes. Check for
bent or kinked hose.
Reconnect burner and valve.
Disconnection of burner to valve.
Sudden drop in gas flow.
Spider webs or insect nest in
venturi tube.
Clean venturi tube.
Burner ports clogged or blocked.
Clean burner ports.
Out of gas.
Call your natural gas company.
Irregular flame pattern,
flame does not run the full
length of burner.
Burner ports are clogged or
blocked.
Clean burner ports.
Flame is yellow or orange.
New burner may have residual
manufacturing oils.
Burn grill for 15 minutes with lid
closed.
Spider webs or insect nest in venturi tube.
Clean venturi tube.
Food residue, grease or seasoning on burner.
Clean burner. Remove salt from
burner.
Make sure burner venturi tube
is properly connected to the
valve.
Poor alignment of valve to burner
venture tube.
Flame blows out.
High or gusting winds.
Low on propane gas.
Excess flow valve tripped.
Flare-up.
Persistent grease fire.
Grease build-up.
Turn front of grill to face wind or
increase flame height.
Replace or refill propane tank.
Refer to “Sudden drop in gas flow”
and reduce the flame height.
Clean grill.
Excessive fat in meat.
Trim fat from meat before grilling.
Excessive cooking temperature.
Adjust (lower) temperature
accordingly.
Grease trapped by food build-up
around burner system.
Turn knobs to the OFF position.
Leave lid in closed position
and let fire burn out. After grill
cools, remove and clean all
parts.
Flashback fire in burner
tube(s).
Inside of lid is peeling – like
paint peeling.
GSF2616
Owner’s Manual
Burner and/or burner venturi tubes are
blocked.
Baked on grease build-up has
turned to carbon and is flaking off.
21
Clean burner and/or burner
venturi tubes
Clean thoroughly.
Warranty Program
Proof of purchase is required to access this warranty program, which is in effect from the date of purchase. Inability to
provide proof of purchase or after the warranty has expired, customers will be subject to parts, shipping and handling fees.
Product Registration is required to receive full warranty coverage, which is in effect from the date of purchase. Inability to
register products within ten days from the date of purchase may result in charges including parts, shipping and handling
fees. Customers can register their products online at www.pyromagicbbq.com or by returning the mail-in registration
card.
Limited Warranty
10 Year Warranty on stainless steel burners.
1 Year Warranty on all parts in regards to damage affecting the operation of the gas grill.
Warranty Provisions:
This warranty is non-transferable and does not cover failures due to misuse or improper installation or maintenance.
This warranty is for replacement of defective parts only. We are not responsible for incidental or consequential damages
or labor costs.
This warranty does not cover chips and scratches of porcelain or painted surfaces, nor does it cover corrosion or
discoloration due to misuse, lack of maintenance, hostile environment, accidents, alterations, abuse or neglect.
This warranty does not cover damage caused by heat, abrasive and chemical cleaners, resulting in chipped porcelain
enamel parts or any damage to other components used in the installation or operation of the gas grill.
Some state do not allow the limitation or exclusion of incidental or consequential damages, so the above limitations
or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights
that vary from state to state.
If you have any questions related to the product or warranty, please visit our website at www.pyromagicbbq.com
or call our customer service center at 1-877-885-8227, 6:00 AM to 5:00 PM (PST), Monday through Friday.
Manufactured by:
Lucas Innovation Inc.
Xiekeng District, QingXi Town,
Dong Guan, Guang Dong, China
GSF2616
Owner’s Manual
22
Printed in China
">