® Undercounter Dishwasher PRODUCT MODEL NUMBERS KUDC03FV KUDC03IV KUDC20CV KUDC20FV KUDE40CV KUDE45CV KUDE60FV KUDE70CV PRODUCT DIMENSIONS KUDE70FV KUDL03FV KUDL40CV KUDS30IV KUDS40CV KUDS40FV KUDS50FV KUDS50SV Electrical Requirements: 120-volt, 60-Hz, AC-only, 15- or 20-amp fused electrical supply. Copper wire only. A timedelay fuse or circuit breaker and separate circuit is recommended. If direct wiring dishwasher: Use flexible, armored or nonmetallic, sheathed copper wire with grounding wire that meets the wiring requirements for your home and local codes and ordinances. Use a UL Listed or CSA Approved conduit connector. If connecting dishwasher with a power supply cord: Use Power Supply Cord Kit (Part Number 4317824) marked for use with dishwashers. Follow the kit instructions for installing the power supply cord. Power supply cord must plug into a grounded three-prong, outlet, located in the cabinet next to the dishwasher opening. Outlet must meet all local codes and ordinances. Water Supply Requirements: A hot water line with 20 to 120 psi (138 to 862 kPa) water pressure. Water temperature must be 120°F (49°C) water at dishwasher. Use 3/8" O.D. copper tubing with compression fitting or flexible braided water supply line (¹⁄₂" minimum plastic tubing is not recommended). Use a 90° elbow with ³⁄₈" N.P.T. external pipe threads on one end. Do not solder within 6" (15.2 cm) of the water inlet valve. Drain Requirements: A new drain hose is supplied with your dishwasher. If this is not long enough, use a new drain hose with a maximum length of 12' (3.7 m) (Part Number 3385556) that meets all current AHAM/IAPMO test standards, is resistant to heat and detergent, and fits the 1" (2.5 cm) drain connector of the dishwasher. Make sure to connect the drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20" (50.8 cm) minimum above the floor. It is recommended that the drain hose either be looped up and securely fastened to the underside of the counter, or be connected to an air gap. Make sure to use an air gap air gap if the drain hose is connected to house plumbing lower than 20" (50.8 cm) above subfloor or floor. Use ¹⁄₂" (1.3 cm) minimum I.D. drain line fittings. If required, the air gap should be installed in accordance with the air gap installation instructions. When connecting the air gap a rubber hose (not provided) will be needed to connect to the waste tee or disposer unit. ) .1 (64 ( 62 .2 cm c m) (60 .6 cm ) 9 (1. (86 wi cm th ) remwh mi.n ov eels ed *Insulation may be compressed. (not used on all models) )* cm " 21 cm) .3 (53 Page 1 of 2 Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice. Dimensions are for planning purposes only. For complete details, see Installation Ref. W10275503B-D-KA 8/10 Instructions packed with product. Specifications subject to change without notice. CABINET CUTOUT DIMENSIONS " 24cm) (6124" cm ) (61 ** Check that all surfaces have no protrusions that would prohibit dishwasher installation. (17 " 34 m) c .4 (86min* 4" m) . (10 2c .2 c m) (4. 4c m) 3" m) (6. 4c 6c (7. m) (26 .7 c (15 .9 m) cm ) Cle Arear a 2" m) cm ) c (4 .4 NOTE: Shaded area of cabinet walls show where utility connections may be installed. **Measured from the lowest point on the underside of countertop. May be reduced to 33⁷⁄₈" (86 cm) by removing wheels from dishwasher. **Minimum, measured from narrowest point of opening. 1 (5. Page 2 of 2 Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice. Dimensions are for planning purposes only. For complete details, see Installation Ref. W10275503B-D-KA 8/10 Instructions packed with product. Specifications subject to change without notice.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project