Roland FA-66 Owner`s manual

Roland FA-66 Owner`s manual
FA-66_e.book 1 ページ 2006年1月12日 木曜日 午前11時32分
OWNER’S MANUAL
201a
Before using this unit, carefully read the sections entitled: “USING THE UNIT
SAFELY” and “IMPORTANT NOTES” (p. 3–p. 6). These sections provide important
information concerning the proper operation of the unit. Additionally, in order to
feel assured that you have gained a good grasp of every feature provided by your
new unit, OWNER’S MANUAL should be read in its entirety. The manual should be
saved and kept on hand as a convenient reference.
Copyright © 2005 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form
without the written permission of ROLAND CORPORATION.
FA-66_e.book 2 ページ 2006年1月12日 木曜日 午前11時32分
For the U.K.
IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
BLUE:
NEUTRAL
BROWN: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug.
For EU Countries
This product complies with the requirements of European Directive 89/336/EEC.
For the USA
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class B Limit.
For Canada
NOTICE
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
AVIS
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
For the USA
DECLARATION OF CONFORMITY
Compliance Information Statement
Model Name :
Type of Equipment :
Responsible Party :
Address :
Telephone :
2
FA-66
FireWire Audio Interface
Roland Corporation U.S.
5100 S. Eastern Avenue Los Angeles, CA 90040-2938
(323) 890 3700
FA-66_e.book 3 ページ 2006年1月12日 木曜日 午前11時32分
USING THE UNIT SAFELY
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers
other adverse effects
respect to the home
furnishings, as well
animals or pets.
to damage or
caused with
and all its
to domestic
001
• Before using this unit, make sure to read the
instructions below, and the Owner’s
Manual.
...................................................................................................................
002c
• Do not open (or modify in any way) the unit
or its AC adaptor.
...................................................................................................................
003
• Do not attempt to repair the unit, or replace
parts within it (except when this manual
provides specific instructions directing you
to do so). Refer all servicing to your retailer, the
nearest Roland Service Center, or an authorized
Roland distributor, as listed on the “Information”
page.
...................................................................................................................
004
• Never use or store the unit in places that
are:
• Subject to temperature extremes (e.g.,
direct sunlight in an enclosed vehicle,
near a heating duct, on top of heat-generating equipment); or are
• Damp (e.g., baths, washrooms, on wet
floors); or are
• Humid; or are
• Exposed to rain; or are
• Dusty; or are
• Subject to high levels of vibration.
...................................................................................................................
007
• Make sure you always have the unit placed
so it is level and sure to remain stable.
Never place it on stands that could wobble,
or on inclined surfaces.
...................................................................................................................
008c
• Be sure to use only the AC adaptor supplied
with the unit. Also, make sure the line
voltage at the installation matches the input
voltage specified on the AC adaptor’s body. Other
AC adaptors may use a different polarity, or be
designed for a different voltage, so their use could
result in damage, malfunction, or electric shock.
...................................................................................................................
The
symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
The
symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.
008e
• Use only the attached power-supply cord.
Also, the supplied power cord must not be
used with any other device.
..................................................................................................................
009
• Do not excessively twist or bend the power
cord, nor place heavy objects on it. Doing so
can damage the cord, producing severed
elements and short circuits. Damaged cords are fire
and shock hazards!
..................................................................................................................
010
• This unit, either alone or in combination
with an amplifier and headphones or
speakers, may be capable of producing
sound levels that could cause permanent hearing
loss. Do not operate for a long period of time at a
high volume level, or at a level that is uncomfortable. If you experience any hearing loss or
ringing in the ears, you should immediately stop
using the unit, and consult an audiologist.
..................................................................................................................
011
• Do not allow any objects (e.g., flammable
material, coins, pins); or liquids of any kind
(water, soft drinks, etc.) to penetrate the
unit.
..................................................................................................................
012b
• Immediately turn the power off, remove the
AC adaptor from the outlet, and request
servicing by your retailer, the nearest
Roland Service Center, or an authorized Roland
distributor, as listed on the “Information” page
when:
• The AC adaptor, the power-supply cord, or the
plug has been damaged; or
• If smoke or unusual odor occurs
• Objects have fallen into, or liquid has been
spilled onto the unit; or
• The unit has been exposed to rain (or otherwise
has become wet); or
• The unit does not appear to operate normally or
exhibits a marked change in performance.
..................................................................................................................
3
FA-66_e.book 4 ページ 2006年1月12日 木曜日 午前11時32分
012d
• Immediately turn the power off, and
request servicing by your retailer, the
nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” page when:
• If smoke or unusual odor occurs
• Objects have fallen into, or liquid has been
spilled onto the unit; or
• The unit has been exposed to rain (or otherwise
has become wet); or
• The unit does not appear to operate normally or
exhibits a marked change in performance.
...................................................................................................................
013
• In households with small children, an adult
should provide supervision until the child
is capable of following all the rules essential
for the safe operation of the unit.
...................................................................................................................
014
• Protect the unit from strong impact.
(Do not drop it!)
...................................................................................................................
015
• Do not force the unit’s power-supply cord
to share an outlet with an unreasonable
number of other devices. Be especially
careful when using extension cords—the total power
used by all devices you have connected to the
extension cord’s outlet must never exceed the power
rating (watts/amperes) for the extension cord.
Excessive loads can cause the insulation on the cord
to heat up and eventually melt through.
...................................................................................................................
016
• Before using the unit in a foreign country,
consult with your retailer, the nearest
Roland Service Center, or an authorized
Roland distributor, as listed on the “Information”
page.
...................................................................................................................
023
• DO NOT play a CD-ROM disc on a conventional audio CD player. The resulting sound
may be of a level that could cause
permanent hearing loss. Damage to speakers or
other system components may result.
...................................................................................................................
101b
• The unit and the AC adaptor should be
located so their location or position does not
interfere with their proper ventilation.
..................................................................................................................
102c
• Always grasp only the plug on the AC
adaptor cord when plugging into, or
unplugging from, an outlet or this unit.
..................................................................................................................
103b
• At regular intervals, you should unplug the
AC adaptor and clean it by using a dry cloth
to wipe all dust and other accumulations
away from its prongs. Also, disconnect the power
plug from the power outlet whenever the unit is to
remain unused for an extended period of time. Any
accumulation of dust between the power plug and
the power outlet can result in poor insulation and
lead to fire.
..................................................................................................................
104
• Try to prevent cords and cables from
becoming entangled. Also, all cords and
cables should be placed so they are out of
the reach of children.
..................................................................................................................
106
• Never climb on top of, nor place heavy
objects on the unit.
..................................................................................................................
107c
• Never handle the AC adaptor or its plugs
with wet hands when plugging into, or
unplugging from, an outlet or this unit.
..................................................................................................................
108b
• Before moving the unit, disconnect the AC
adaptor and all cords coming from external
devices.
..................................................................................................................
108c
• Disconnect all cords coming from external
devices before moving the unit.
..................................................................................................................
109b
• Before cleaning the unit, turn off the power
and unplug the AC adaptor from the outlet.
..................................................................................................................
110b
• Whenever you suspect the possibility of
lightning in your area, disconnect the AC
adaptor from the outlet.
..................................................................................................................
118a
• Should you remove the ground terminal
screw, keep them in a safe place out of
children's reach, so there is no chance of
them being swallowed accidentally.
..................................................................................................................
120
• Always turn the phantom power off when
connecting any device other than condenser
microphones that require phantom power.
You risk causing damage if you mistakenly supply
phantom power to dynamic microphones, audio
playback devices, or other devices that don't require
such power. Be sure to check the specifications of
any microphone you intend to use by referring to
the manual that came with it.
(This instrument's phantom power:
48 V DC, 20 mA Max)
..................................................................................................................
4
FA-66_e.book 5 ページ 2006年1月12日 木曜日 午前11時32分
IMPORTANT NOTES
291a
In addition to the items listed under “USING THE UNIT SAFELY” on page 3, please read and
observe the following:
Power Supply
301
• Do not connect this unit to same electrical
outlet that is being used by an electrical
appliance that is controlled by an inverter
(such as a refrigerator, washing machine,
microwave oven, or air conditioner), or that
contains a motor. Depending on the way in
which the electrical appliance is used, power
supply noise may cause this unit to
malfunction or may produce audible noise. If
it is not practical to use a separate electrical
outlet, connect a power supply noise filter
between this unit and the electrical outlet.
302
• The AC adaptor will begin to generate heat
after long hours of consecutive use. This is
normal, and is not a cause for concern.
307
• Before connecting this unit to other devices,
turn off the power to all units. This will help
prevent malfunctions and/or damage to
speakers or other devices.
Placement
351
• Using the unit near power amplifiers (or other
equipment containing large power transformers) may induce hum. To alleviate the
problem, change the orientation of this unit;
or move it farther away from the source of
interference.
355b
• When moved from one location to another
where the temperature and/or humidity is
very different, water droplets (condensation)
may form inside the unit. Damage or
malfunction may result if you attempt to use
the unit in this condition. Therefore, before
using the unit, you must allow it to stand for
several hours, until the condensation has
completely evaporated.
Maintenance
401a
• For everyday cleaning wipe the unit with a
soft, dry cloth or one that has been slightly
dampened with water. To remove stubborn
dirt, use a cloth impregnated with a mild,
non-abrasive detergent. Afterwards, be sure
to wipe the unit thoroughly with a soft, dry
cloth.
402
• Never use benzine, thinners, alcohol or
solvents of any kind, to avoid the possibility
of discoloration and/or deformation.
Additional Precautions
553
• Use a reasonable amount of care when using
the unit’s buttons, sliders, or other controls;
and when using its jacks and connectors.
Rough handling can lead to malfunctions.
556
• This device may interfere with radio and
television reception. Do not use this device in
the vicinity of such receivers.
• When connecting / disconnecting all cables,
grasp the connector itself—never pull on the
cable. This way you will avoid causing shorts,
or damage to the cable’s internal elements.
352b
557
352a
• Noise may be produced if wireless communications devices, such as cell phones, are
operated in the vicinity of this unit. Such noise
could occur when receiving or initiating a call,
or while conversing. Should you experience
such problems, you should relocate such
wireless devices so they are at a greater
distance from this unit, or switch them off.
• A small amount of heat will radiate from the
unit during normal operation.
558a
• To avoid disturbing your neighbors, try to
keep the unit’s volume at reasonable levels.
You may prefer to use headphones, so you do
not need to be concerned about those around
you (especially when it is late at night).
5
FA-66_e.book 6 ページ 2006年1月12日 木曜日 午前11時32分
IMPORTANT NOTES
559a
• When you need to transport the unit, package
it in the box (including padding) that it came
in, if possible. Otherwise, you will need to use
equivalent packaging materials.
562
• Use a cable from Roland to make the
connection. If using some other make of
connection cable, please note the following
precautions.
• Some connection cables contain resistors.
Do not use cables that incorporate resistors
for connecting to this unit. The use of such
cables can cause the sound level to be
extremely low, or impossible to hear. For
information on cable specifications, contact
the manufacturer of the cable.
Handling CD-ROMs
801
• Avoid touching or scratching the shiny
underside (encoded surface) of the disc.
Damaged or dirty CD-ROM discs may not be
read properly. Keep your discs clean using a
commercially available CD cleaner.
Copyright
851
• Unauthorized recording, distribution, sale,
lending, public performance, broadcasting, or
the like, in whole or in part, of a work
(musical composition, video, broadcast, public
performance, or the like) whose copyright is
held by a third party is prohibited by law.
852a
• When exchanging audio signals through a
digital connection with an external
instrument, this unit can perform recording
without being subject to the restrictions of the
Serial Copy Management System (SCMS).
This is because the unit is intended solely for
musical production, and is designed not to be
subject to restrictions as long as it is used to
record works (such as your own compositions) that do not infringe on the copyrights of
others. (SCMS is a feature that prohibits
second-generation and later copying through
a digital connection. It is built into MD
recorders and other consumer digital-audio
equipment as a copyright-protection feature.)
853
• Do not use this unit for purposes that could
infringe on a copyright held by a third party.
We assume no responsibility whatsoever with
regard to any infringements of third-party
copyrights arising through your use of this
unit.
204
* Microsoft and Windows are registered trademarks of Microsoft Corporation.
206e
* The screen shots in this document are used in compliance with the guidelines of the
Microsoft Corporation.
206j
* Windows® is known officially as: “Microsoft® Windows® operating system.”
207
* Apple and Macintosh are registered trademarks of Apple Computer, Inc.
209
* Mac OS is a trademark of Apple Computer, Inc.
220
* All product names mentioned in this document are trademarks or registered trademarks
of their respective owners.
6
FA-66_e.book 7 ページ 2006年1月12日 木曜日 午前11時32分
Contents
Contents of the package.............................................................................. 8
Front and rear panel................................................................................... 10
Front panel.........................................................................................................................10
Rear panel ..........................................................................................................................14
Before you begin using the FA-66 with your Macintosh
(Mac OS X users) ....................................................................................... 18
Audio and MIDI settings .................................................................................................19
Software settings...............................................................................................................23
Installing the driver (Windows) ................................................................. 24
Giving priority to background services.........................................................................29
Driver settings ...................................................................................................................30
Basic connections and settings................................................................ 35
Basic connections ..............................................................................................................35
Recording a mic or guitar ................................................................................................36
Recording a digital signal ................................................................................................38
Connecting various types of equipment .......................................................................39
Software settings........................................................................................ 40
SONAR 4 ............................................................................................................................40
Digital Performer ..............................................................................................................43
Logic ...................................................................................................................................44
Cubase SX/SL ...................................................................................................................45
FA-66 Driver Settings dialog box (Windows)...............................................................46
Troubleshooting ......................................................................................... 48
Driver-related problems (Windows)..............................................................................48
No sound............................................................................................................................51
Noise or pops are heard when recording/playing on your computer.....................55
Noise or distortion occurs when the FA-66 is not connected to your computer.....59
The sound is too weak......................................................................................................59
Others .................................................................................................................................61
Main specifications .................................................................................... 62
Index ............................................................................................................ 64
7
FA-66_e.book 8 ページ 2006年1月12日 木曜日 午前11時32分
Contents of the package
■ FA-66
fig.FA-66
■ AC adaptor
This is the dedicated AC adaptor for the FA-66. Use only the supplied AC
adaptor.
■ FireWire (IEEE 1394) cables
(one 6-pin ↔ 6-pin cable, one 6-pin ↔ 4-pin cable)
Use one of these cables to connect the FA-66 to the IEEE 1394 connector
(FireWire connector, iLink connector, DV connector) of your computer.
The 6-pin ↔ 4-pin cable cannot supply bus power.
* Use only the FireWire (IEEE 1394) cables. If the supplied FireWire (IEEE 1394)
cable becomes damaged or lost and you need a replacement, please contact the nearest
Roland Service Center, or an authorized Roland distributor, as listed on the
“Information” page.
■ Owner’s manual
This is the manual you are reading. Please keep it at hand for reference.
■ CD-ROM
This contains Windows drivers for the FA-66 and demo songs.
* Be careful not to touch or scratch the recorded surface (unprinted surface) of the disc.
Doing so may render the disc unreadable. If the disc gets dirty, use a commercially
available CD cleaner to clean it.
Do not play back the CD-ROM in a conventional audio
CD player. Doing so may produce high-volume sound
that can damage your hearing and/or speakers.
8
FA-66_e.book 9 ページ 2006年1月12日 木曜日 午前11時32分
Contents of the package
You will need to provide these items yourself
An external amp, speakers, headphones, and mic are not included
The external amp, speakers, or headphones you’ll need to hear the sound
output from the FA-66 and the cables you’ll need to connect these items are not
included. Nor is a mic included, which you will need to connect to the FA-66 in
order to input audio. You will need to obtain these items yourself.
An MD or DAT recorder and digital input/output cables are not included
You can use an MD or DAT digital recorder to record, but the cables needed to
connect these devices to the FA-66 are not included. You will need to obtain
these items yourself.
9
FA-66_e.book 10 ページ 2006年1月12日 木曜日 午前11時32分
Front and rear panel
Front panel
fig.front.eps_60
1
2
3 4 5 6 9 10
7 8
11
12
13
fig.jack-type_70
1. Combo input jacks
These are analog audio input jacks with mic preamps. They
accommodate either XLR or phone plugs, allowing you to
connect a variety of equipment. Either balanced or unbalanced
signals may be connected.
Phantom power (48 V) is provided for XLR type connections,
allowing you to connect condenser mics that require phantom
power. In this case, turn on the phantom power switch
(19) located on the rear panel.
XLR plug
TRS phone
Phone plug
plug
(unbalanced) (balanced)
fig.XLR-TRS
* This instrument is equipped
with balanced (XLR/TRS) type
1:GND
2:HOT
input jacks. Wiring diagrams for
3:COLD
these jacks are shown on the
right. Make connections after
first checking the wiring
diagrams of other equipment you intend to connect.
GND(SLEEVE)
HOT(TIP)
COLD(RING)
2. Input sensitivity knobs
These adjust the input level of the signals input to the front panel combo input
jacks (1).
3. Input impedance select switch
This switch selects either high impedance (Hi-Z) or low impedance (Lo-Z) as the
type of device connected to the INPUT 2 phone jack of the combo input jacks
(1). If you have connected a guitar or bass to this jack, select the high impedance
(Hi-Z) setting; if you have connected a mic, select the low impedance (Lo-Z) setting.
* Combo input jack INPUT 1 is fixed at low impedance (Lo-Z).
fig.front.eps
10
FA-66_e.book 11 ページ 2006年1月12日 木曜日 午前11時32分
Front and rear panel
4. Peak/Limiter indicator
This indicates whether the signal being input via the combo input jacks (1) is
distorting, or whether the limiter is operating.
Limiter switch
Limiter on
Status
Limiter off
The indicator will function as a peak indicator. Use the input sensitivity knobs for each input jack to adjust the input level so that the
peak indicator does not light red. The red LED will light if the sound
distorts.
The indicator will function as a limiter indicator. When the input signal exceeds a certain level, the limiter will operate and the indicator
will light green.
5. Power indicator
Lights when the power is on.
6. Output indicator
This will light green if signals are being sent from the computer’s audio output
ports 1 and 2 (OUT 1/2).
(see block diagram ➔ front cover)
7. Digital input switch
If you want to record a digital input, turn this on ( pressed inward). This lets the
FA-66 synchronize to an external digital device connected to the digital input
connector (25)
8. Sync indicator
When the digital input switch (7) is on, this indicator shows the status of
synchronization with a digital device connected to the digital input connector
(25). (external synchronization mode)
Lit
Blinking
Synchronized correctly.
Not synchronized. Check that your digital device is correctly connected to
the digital input connector.
Also make sure that the connected digital device is set to the same sampling frequency as that selected by the FA-66’s sample rate select
switch (18).
11
FA-66_e.book 12 ページ 2006年1月12日 木曜日 午前11時32分
Front and rear panel
fig.front.eps_60
1
3 4 5 6 9 10
2
7 8
11
12
13
9. STEREO/MONO select switch (direct monitor section)
This selects whether the input signal is to be monitored in stereo (STEREO) or in
monaural (MONO). Turn this on ( pressed inward) if you want to monitor in
monaural.
For example, if you’ve connected a guitar only to INPUT 2/R, you would use the
monaural setting ( inward position). Even with the monaural (MONO) setting, the
audio signal being sent via FireWire (IEEE 1394) to the computer will be stereo.
10. Direct monitor soft control switch (direct monitor mixer section)
Turn this on ( pressed inward) if you want to control the direct monitor mixer (see
block diagram ➔ front cover) from your ASIO 2.0 compatible software. If this is on,
your software will be able to control the monitor volume, pan, and on/off status of
each input jack.
If this is off, all settings of the direct monitor mixer will be ignored (= bypassed),
allowing you to monitor the input signals from all input jacks. This is convenient if
you want to check the connections while temporarily ignoring the software settings.
* This function is available only on Windows.
11. Direct monitor volume (direct monitor section)
fig.direct-volume
12
This adjusts the monitor volume.
Turning this knob toward the left
(OUT1/2) will decrease the level of the
sound being input through the input
jacks. Turning the knob toward the
right (MONITOR) will decrease the
level of the sound being output from
your computer. At the center position,
the sound being output from your
computer and the sound being input
via the input jacks will both be at 100%
of their level.
Volume
100%
MONITOR
MONITOR
0%
100%
OUT 1/2
0%
FA-66_e.book 13 ページ 2006年1月12日 木曜日 午前11時32分
Front and rear panel
12. Output volume
This adjusts the volume that is output from the headphone jack (13) and Main
output jacks (22).
13. Headphone jack
This jack outputs the mixed sound being input via the input jacks and the sound
being output from the computer (WAVE OUT 1/2 (in the case of WDM, EDIROL
FA-66 Out 1➔ see p. 31)). The balance of these two is adjusted by the direct
monitor volume (11).
Even if headphones are connected, the sound being sent from the rear panel’s main
output jacks (MAIN OUT) (22) will not be cut off.
13
FA-66_e.book 14 ページ 2006年1月12日 木曜日 午前11時32分
Front and rear panel
Rear panel
fig.rear.eps_60
14 15 18
16
17
19
20
23
21
24
25
22
26
27
14. Grounding terminal
Depending on the circumstances of a particular setup, you may experience a
discomforting sensation, or perceive that the surface feels gritty to the touch when
you touch this device, microphones connected to it, or the metal portions of other
objects, such as guitars. This is due to an infinitesimal electrical charge, which is
absolutely harmless. However, if you are concerned about this, connect the ground
terminal (see figure) with an external ground. When the unit is grounded, a slight
hum may occur, depending on the particulars of your installation. If you are unsure
of the connection method, contact the nearest Roland Service Center, or an
authorized Roland distributor, as listed on the “Information” page.
Unsuitable places for connection
•
•
•
Water pipes (may result in shock or electrocution)
Gas pipes (may result in fire or explosion)
Telephone-line ground or lightning rod (may be dangerous in the event of lightning)
fig.power-sw
15. Power switch
Used to switch the power on (DC IN) or off (OFF), and for
switching to bus power (BUS).
BUS
The FA-66 can operate on bus power if it’s connected to your
computer via a 6-pin ↔ 6-pin FireWire (IEEE 1394) cable.
In this case, power is supplied from your computer via the
FireWire (IEEE 1394) cable. If you want to use bus power, set
the power switch to the BUS position.
fig.6-pin
• 6-pin type
You can use bus power if your computer has a 6-pin IEEE 1394 connector
(FireWire connector, iLink connector, DV connector).
* With some computers, the FA-66 may not operate on bus power. If so, connect the
included AC adaptor to an AC outlet and use it to supply power to the FA-66. In this
case, the power will be on when you set the power switch to the DC IN position.
fig.4-pin
• 4-pin type
If your computer has a 4-pin FireWire (IEEE 1394) connector, you cannot use bus
power. Connect the included AC adaptor to the AC adaptor jack, and set the
power switch to DC IN.
14
FA-66_e.book 15 ページ 2006年1月12日 木曜日 午前11時32分
Front and rear panel
16. AC adaptor jack
Connect the included AC adaptor to this jack.
* Never use any AC adaptor other than the supplied unit; doing so may cause
malfunction.
17. FireWire (IEEE 1394) connectors
Use a FireWire (IEEE 1394) cable to connect these to your computer.
We recommend that you use a 6-pin cable to connect the FA-66 to your computer,
and a 4-pin cable to connect the FA-66 to any peripheral device you may be using.
fig.6-pin
fig.4-pin
• 6-pin connector
If the IEEE 1394 connector (FireWire connector, iLink connector, DV connector)
of your computer is a 6-pin type, use the included 6-pin ↔ 6-pin cable.
The FA-66 will be able to operate on bus power. Normally you should use this
method of connection.
If the IEEE 1394 connector (FireWire connector, iLink connector, DV connector) of
your computer is a 4-pin type, use the included 6-pin ↔ 4-pin cable. However, in
this case, the FA-66 will not operate on bus power.
• 4-pin connector
Normally, the 4-pin connector is used when connecting the FA-66 to a peripheral
device.
18. Sample rate select switch
This specifies the sampling frequency at which audio data will be recorded and
played back. In order to get this setting to take effect, you must exit all of your
software, then cycle the power to the FA-66 (switch it off, then back on again).
* If you are using Macintosh and want to change the sampling frequency, you must
first power down the FA-66. Then, access the Mac OS System Preferences Sound, and verify that EDIROL FA-66 has disappeared from the Input and
Output panes. Then, power up the FA-66 again. For information on how to display
the Mac OS System Preferences - Sound, refer to “Audio settings” (p. 19).
You must set the sample rate select switch to match the sampling frequency
selected in the software you are using. If you use external synchronization mode
(i.e., the DIGITAL IN switch turned on), the external device’s sampling frequency
must also be the same.
[ Limitations when using the FA-66 at 192 kHz ]
• You will not be able to use the digital input connector or digital output
connector.
15
FA-66_e.book 16 ページ 2006年1月12日 木曜日 午前11時32分
Front and rear panel
fig.rear.eps_60
14 15 18
16
19
17
20
23
21
24
25
22
26
27
19. Phantom power switch
This is an on/off switch for the phantom power supplied to the XLR connectors of
the combo input jacks (1) on the front panel.
* You must leave the phantom power turned off (right position) unless condenser mics
requiring phantom power are connected to the XLR jacks. Supplying phantom power
to a dynamic mic or an audio playback device may cause malfunction. For details on
the requirements of your mic, refer to its owner’s manual.
(The FA-66’s phantom power supply: DC 48 V, 20 mA maximum)
20. Limiter switch
This turns the FA-66’s hardware limiter on/off.
If a sudden, high-volume sound is input to the combo input jacks (1), the limiter
applies mild compression to prevent clipping from occurring at the AD converter.
* Clipping noise will be heard if the input signal exceeds the capacity of the limiter.
21. Output jacks 3, 4 (Nominal output: +4 dBu)
These jacks output analog audio signals. Balanced output is supported.
22. Main output jacks (output jacks 1, 2) (Nominal output: +4 dBu)
These output the mixed sound that is being input via the input jacks and being
output from the computer. You can use the output volume control (12) to adjust
the volume.
23. MIDI IN/OUT connectors
You can connect these to the MIDI connectors of your MIDI equipment to send and
receive MIDI messages.
24. Digital output connector (optical)
Use this when you want to digitally connect an audio device, such as an MD or DAT
unit.
The signals sent from OUTPUT 5 and 6 (if using WDM, EDIROL FA-66 OUT 3 ➔
see p. 31) are output to the digital output connector.
16
FA-66_e.book 17 ページ 2006年1月12日 木曜日 午前11時32分
Front and rear panel
25. Digital input connector (optical)
Use this when you want to input a digital audio signal from a CD/MD/DAT or
similar device.
The signal input to the digital input connector is input as INPUT 5 and 6 (in
the case of WDM, EDIROL FA-66 In 3 ➔ see p. 31).
If you want to record this digital input signal, turn on the digital input switch
(7).
You must input a signal of the same sampling frequency as that selected by the
sample rate select switch (18).
26. Input jacks 3-4
Input jacks 3 and 4 are designed with a higher gain so that you can connect them
to audio devices that have a lower output level, such as CD players or MIDI sound
modules. If you connect these inputs to a device that has a higher output level, such
as a mixer, use this input level adjustment knob (27) to adjust the level.
If no device is connected to the Input jacks 3 and 4, turn the
input level adjustment knob (27) all the way toward the
left.
27. Input level adjustment knob
This adjusts the level of the sound that is input at input jacks 3 and 4 (26).
17
FA-66_e.book 18 ページ 2006年1月12日 木曜日 午前11時32分
Before you begin using the FA-66
with your Macintosh (Mac OS X users)
If you are using the FA-66 with Windows, please read
“Installing the driver (Windows)” (p. 24).
If you’re using the FA-66 with Mac OS X, you don’t need to
install a driver.
Simply connect the FA-66 to your Macintosh as described
below.
1
2
With the FA-66 disconnected, start up your Macintosh.
Once the connections have
been completed, turn on
power to your various devices
in the order specified. By
turning on devices in the
wrong order, you risk causing
malfunction and/or damage to
speakers and other devices.
Use a FireWire (IEEE 1394) cable to connect the FA-66 to
your Macintosh.
1. With the FA-66’s power switch off, connect the power
cord to it.
2. Plug the AC adaptor cable into an AC outlet.
3. Use a FireWire (IEEE 1394) cable to connect the FA-66
to your Macintosh.
3
Turn on the FA-66’s power switch.
This unit is equipped with a
protection circuit. A brief
interval (a few seconds) after
power up is required before
the unit will operate normally.
The driver will be installed automatically.
Next, you need to make audio device and MIDI device
settings.
18
Once the connections have
been completed, turn on
power to your various devices
in the order specified. By
turning on devices in the
wrong order, you risk causing
malfunction and/or damage to
speakers and other devices.
FA-66_e.book 19 ページ 2006年1月12日 木曜日 午前11時32分
Before you begin using the FA-66 with your Macintosh (Mac OS X users)
Audio and MIDI settings
Audio settings
If you want to use the FA-66 with the iTunes software
included with your Macintosh, specify the input/output
devices as follows.
The procedure for making device settings differs
depending on the software you are using. For details, refer
to the owner’s manual for your software.
1
2
3
4
If you want sound to be played
from the internal speakers of
your Macintosh, choose
“Internal speakers” in the
Output tab. If you don’t want
alerts to be played through the
FA-66, choose “Internal
speakers” for the “Play alerts
and sound effects through”
setting.
From the Apple menu, choose the System Preferences
dialog box, and click Sound.
Click the Sound Effects tab, and choose EDIROL FA-66
for the “Play alerts and sound effects through” setting.
Click the Output tab, and choose EDIROL FA-66 for the
“Choose a device for sound output” setting.
If the Input tab is shown, choose EDIROL FA-66 for the
“Choose a device for sound output” setting.
Cautions for use
Before you use your software with the FA-66, please note the following.
• Before you start up your software, use a FireWire (IEEE 1394) cable to
connect the FA-66 with your computer, and turn on the power.
• Do not disconnect the FA-66’s FireWire (IEEE 1394) cable or switch off the
power to the FA-66 while your software is running.
• Close your software before you switch off the FA-66’s power.
• Turn off the Sleep setting of your Macintosh.
• The FA-66 will not work in the Classic environment of Mac OS X. Use it
when the Classic environment is not running.
• Turn off the energy conservation settings of your Macintosh.
• If the Options pane of the Energy Saver preferences on your Macintosh
has a Processor Performance setting, choose the “Highest” setting.
19
FA-66_e.book 20 ページ 2006年1月12日 木曜日 午前11時32分
Before you begin using the FA-66 with your Macintosh (Mac OS X users)
* Depending on the model of Macintosh you are using, starting
up the Macintosh when the FA-66 is connected may cause
operation to become unstable. In this case, start up the
Macintosh and then connect the FA-66.
* If you want to change the FA-66’s sample rate, turn the FA-66
off, change the sample rate, and then turn the FA-66 on again.
If, in the Mac OS System Preferences - Sound - Output, the
EDIROL FA-66 is not shown in the “Choose a device for
sound output” setting, this means that the FA-66 is
completely powered down.
20
FA-66_e.book 21 ページ 2006年1月12日 木曜日 午前11時32分
Before you begin using the FA-66 with your Macintosh (Mac OS X users)
MIDI settings
1
Open the Applications folder of your Macintosh hard
disk. In the Utilities folder, double-click Audio MIDI
Setup to open the Audio MIDI Setup.
fig.audio-midi.eps
2
3
4
2
3
Click MIDI Devices
Click Add Device
Use the mouse to
drag a connection
Click the MIDI Devices tab.
Click Add Device.
New external device will appear.
4
Connect the t and s symbols (which signify the outputs
and inputs) of the EDIROL FA-66 icon to those of the New
External Device icon by using the mouse to drag between
them.
* Change icons and set other items according to the MIDI
devices that are connected to the FA-66’s MIDI connectors.
If you double-click new external device, the new external
device Properties dialog box will appear, allowing you to
specify a variety of things, such as the device name.
5
Close the Audio MIDI Setup dialog box to complete the
procedure.
21
FA-66_e.book 22 ページ 2006年1月12日 木曜日 午前11時32分
Before you begin using the FA-66 with your Macintosh (Mac OS X users)
Checking that you hear sound
Now, let’s play back the sample data to verify that the
connections and settings are correct. We will use iTunes to
play back the sample data provided on the included CDROM.
Before you continue, connect headphones or monitor
speakers to the FA-66 as described in “Basic
connections” (p. 35).
1
2
Use of the song data supplied
with this product for any
purpose other than private,
personal enjoyment without
the permission of the
copyright holder is prohibited
by law. Additionally, this data
must not be copied, nor used
in a secondary copyrighted
work without the permission
of the copyright holder.
Set the FA-66’s sample rate select switch to 48 kHz. You’ll
need to cycle the power to the FA-66 after changing the
sampling rate.
Start up iTunes (included with Mac OS).
iTunes is normally located in the Applications folder on
the hard disk.
3
Insert the included CD-ROM into the CD-ROM drive of
your Macintosh.
fig.itune.eps
4
5
From the SampleSong folder of the CD-ROM, drag
TTears(.mp3) into the iTunes window.
Select TTears(.mp3) in the song list, and click
.
Alternatively, you can start playback by pressing the space
bar on your computer keyboard.
If the sample data plays correctly, the FA-66 is correctly
connected to your Macintosh.
22
If the volume is too low, or if
you don’t hear sound at all, try
turning the FA-66’s direct
monitor volume knob (p. 12)
so it’s positioned to the left of
the MIX (center) position.
FA-66_e.book 23 ページ 2006年1月12日 木曜日 午前11時32分
Before you begin using the FA-66 with your Macintosh (Mac OS X users)
About the demo songs
The SampleSong folder on the included CD-ROM contains the following demo
songs. Please copy the demo songs to the hard disk of your Macintosh before
listening to them.
* The demo songs were produced at 48 kHz. You must set the FA-66’s sample rate to
48 kHz. You’ll need to cycle the power to the FA-66 after changing the sampling rate.
for Cubase folder
This folder contains the demo songs as Cubase VST song files (.all) and Cubase
SX project files (.cpr).
If you are using the Cubase SX demo version, the playback will not be correct
since some functionality (such as effects) will not be available.
for Logic folder
This folder contains the demo songs as Logic project files (.lso).
Software settings
Before you start up your software, use a FireWire (IEEE
1394) cable to connect the FA-66 to your computer, and
turn on the power of the FA-66.
If your software allows you to specify MIDI and audio
input/output settings, choose EDIROL FA-66. For details,
refer to the owner’s manual for your software. Also refer to
“Software settings” (p. 40).
For the latest information,
please visit
http://www.edirol.com/
If you have turned on software
monitoring in your application, turn the
FA-66’s hardware monitoring (direct
monitor) off to prevent double monitoring
and to keep an audio feedback loop from
occurring.
23
FA-66_e.book 24 ページ 2006年1月12日 木曜日 午前11時32分
Installing the driver (Windows)
What is a driver?
A driver is software that allows data to be transferred
between the FA-66 and application software running on
your computer when the FA-66 is connected to your
computer via a FireWire (IEEE 1394) cable.
The driver sends data from your application software to
the FA-66, and from the FA-66 to your application
software. The driver is required in order for you to use the
FA-66 while connected to your computer.
1
Depending on your system,
the System icon may be
displayed directly in the
Control Panel (Classic view).
If so, double-click the System
icon.
With the FA-66 disconnected, start up Windows.
* You must log on to Windows with a user name whose account
has administrative privileges (e.g., Administrator).
2
Open the System Properties dialog box.
1. From the Windows start menu, choose Control
Panel.
2. In “Pick a category,” click “Performance and
Maintenance”.
3. In “or Pick a Control Panel icon,” click the System
icon.
fig.signature
3
Click the Hardware
tab, and then click
[Driver Signing].
The Driver Signing
Options dialog box
appears.
4
In the Driver Signing Options dialog box, make sure that
“Ignore” is selected.
If “Ignore” is selected, simply click [OK]. If “Ignore” is not
selected, make a note of the current setting (Warn or Block),
change the setting to “Ignore”, and click [OK].
24
If you change the “Driver
Signing Options” setting,
change it back to the original
setting after you’ve installed
the driver.
If the screen indicates
“Windows can perform the
same action each time you
insert a disk or connect a
device with this kind of file,”
click [Cancel].
FA-66_e.book 25 ページ 2006年1月12日 木曜日 午前11時32分
Installing the driver (Windows)
5
6
Click [OK] to close the System Properties dialog box.
Close all currently running software (applications).
Also close all windows that are open. If you are using
software such as antivirus programs, be sure to close these
programs as well.
7
Find the included CD-ROM.
Insert the CD-ROM into your computer’s CD-ROM drive.
8
Checking the name of your
drive. From the start menu,
choose My Computer. In the
window that appears, verify
the name of the CD-ROM
drive into which you inserted
the CD-ROM in step 7. The
(D:) or (E:) displayed by the
CD-ROM drive icon
is the
drive name.
From the Windows start menu, choose “Run...”
The “Run” dialog box will appear.
9
Input the name into the dialog box as shown, and click
[OK].
fig.win-run
(Drive name): \Driver\XP_ENG\setup.exe
If you want to install the driver
into a different hard disk, click
[Browse] and specify the
desired location.
* The drive name is “D:” in the example shown here, but this
may be different on your system. Specify the drive name for
your CD-ROM drive.
10
The EDIROL FA-66 Driver Setup dialog box appears.
Click [Install].
25
FA-66_e.book 26 ページ 2006年1月12日 木曜日 午前11時32分
Installing the driver (Windows)
fig.caution.eps
If the setting in the Driver
Signing Options dialog
box is not set to “Ignore,”
a dialog box like the
following will appear.
Click [Continue
Anyway] to continue
driver installation.
11
A dialog box entitled “Setup is now ready to install the
drivers” appears.
Use a FireWire (IEEE 1394) cable to connect the FA-66 to
your computer.
1. With the power switch turned off, connect the AC
adaptor to the FA-66.
Once the connections have
been completed, turn on
power to your various devices
in the order specified. By
turning on devices in the
wrong order, you risk causing
malfunction and/or damage to
speakers and other devices.
2. Plug the AC adaptor’s power cord into an AC outlet.
3. Use a FireWire (IEEE 1394) cable to connect the FA-66
to your computer.
12
Turn on the power switch of the FA-66.
The “Found New Hardware” message appears near the
taskbar. Please wait.
13
14
A dialog box entitled Welcome to the Found New
Hardware Wizard appears. Make sure that the box
indicates “EDIROL FA-66 Sub 1,” choose “Install the
software automatically (Recommended),” and click
[Next].
A dialog box entitled “Completing the Found New
Hardware Wizard” appears.
Click [Finish].
Once again, the “Found New Hardware” message appears
near the taskbar. Please wait.
26
This unit is equipped with a
protection circuit. A brief
interval (a few seconds) after
power up is required before
the unit will operate normally.
If the Found New Hardware
Wizard asks you whether you
want to connect to Windows
Update, choose “No” and then
click [Next].
FA-66_e.book 27 ページ 2006年1月12日 木曜日 午前11時32分
Installing the driver (Windows)
15
16
A dialog box entitled Welcome to the Found New
Hardware Wizard appears. Make sure that the box
indicates “EDIROL FA-66 Sub 2,” choose “Install the
software automatically (Recommended),” and click
[Next].
A dialog box entitled “Completing the Found New
Hardware Wizard” appears.
Click [Finish].
The “Found New Hardware” message appears near the
taskbar.
17
In the EDIROL FA-66 Driver Setup dialog box that is
already displayed, click [I Completed the Above Steps].
The “Found New Hardware” message appears near the
taskbar.
18
The Welcome to the Found New Hardware Wizard
dialog box appears. Make sure that the box indicates
“EDIROL FA-66,” choose “Install the software
automatically (Recommended),” and click [Next].
A dialog box like the following will appear if “Driver
Signing Options” is not set to “Ignore.”
If a dialog box with the “!” symbol appears...
1. Click [Continue Anyway].
2. Continue with the installation.
If a dialog box with the “X” symbol appears...
1. Click [OK].
2. When the “Found New Hardware Wizard” appears,
click [Finish].
3. Return to step 1 (p. 24), and re-install the driver from
the beginning.
19
A dialog box entitled “Completing the Found New
Hardware Wizard” appears. Click [Finish].
Once again, the “Found New Hardware” message appears
near the taskbar.
This completes driver installation.
27
FA-66_e.book 28 ページ 2006年1月12日 木曜日 午前11時32分
Installing the driver (Windows)
If you changed the “Driver Signing Options” setting (p. 24, step 4), restore the
setting to its previous state after restarting Windows.
1. Log on to Windows using the same user account as the one used
when the driver was installed.
2. From the Windows start menu, choose Control Panel.
3. In “Pick a category,” click Performance and Maintenance.
4. In “or Pick a Control Panel icon,” click the System icon. The
System Properties dialog box appears.
* Depending on your system, the System icon may be shown directly in the
Control Panel (Classic view). If so, double-click the System icon.
5. Click the Hardware tab, and then click [Driver Signing]. The Driver
Signing Options dialog box appears.
6. In Driver Signing Options, restore the previous setting (“Warn” or
“Block”) and click [OK].
7. Click [OK]. The System Properties dialog box closes.
Next, you need to set your computer so priority is given to
background services, which will help to assure that audio
and MIDI processing occur smoothly.
(-> “Giving priority to background services” (p. 29))
28
FA-66_e.book 29 ページ 2006年1月12日 木曜日 午前11時32分
Installing the driver (Windows)
Giving priority to background services
Crackling may occur in the sound if you omit making this
setting. To ensure that audio and MIDI are processed
smoothly, make the setting as follows.
1
Open the System Properties dialog box.
1. From the Windows start menu, choose Control
Depending on your system,
the System icon may be
displayed directly in the
Control Panel (Classic view).
If so, double-click the System
icon.
Panel.
2. In “Pick a category,” click “Performance and
Maintenance”.
3. In “or Pick a Control Panel icon,” click the System
icon.
2
3
Click the Advanced tab.
Click [Settings] located at the right of the Performance
area.
The Performance Options dialog box appears.
fig.background
4
5
6
Click the Advanced
tab.
In Processor
Scheduling, choose
“Background
services,” and click
[OK].
In the System
Properties dialog box,
click [OK]. The
System Properties
dialog box closes.
Next, you need to make audio device and MIDI device
settings.
(-> “Driver settings” (p. 30))
29
FA-66_e.book 30 ページ 2006年1月12日 木曜日 午前11時32分
Installing the driver (Windows)
Driver settings
About the input and output devices
In order to get the best performance from the software you are using, you must
choose the correct device settings. The FA-66’s audio driver supports WDM and
ASIO 2.0.
Audio devices
Audio output device (WDM)
Audio input device (WDM)
ASIO device
EDIROL FA-66 Out 1–3
EDIROL FA-66 In 1–3
EDIROL FA-66
Note 1
Note 1
Note 1: Refer to “How WDM ports correspond to FA-66 output jacks” (p. 31).
MIDI devices
MIDI OUT
MIDI IN
EDIROL FA-66 MIDI OUT
If you specify EDIROL FA-66 as the output port for your sequencer
software, etc., messages will be sent from the FA-66’s MIDI OUT
connector.
EDIROL FA-66 MIDI IN
If you specify EDIROL FA-66 as the input port for your sequencer
software, etc., messages will be received from the FA-66’s MIDI IN
connector.
* For details on how to make settings for your software, you should also refer to the
owner’s manual for your software, as well as to “Software settings” (p. 40).
* If you are unable to select the FA-66 in the device settings of your software, it is
possible that the FA-66 driver was not installed correctly. Please re-install the driver.
30
FA-66_e.book 31 ページ 2006年1月12日 木曜日 午前11時32分
Installing the driver (Windows)
WDM
Use this if you are using the FA-66 with the following applications or situations.
• Conventional applications such as Media Player
(for the settings, refer to “Input/output device settings” (p. 32))
• WDM driver mode compatible applications such as SONAR
• DirectSound compatible applications
ASIO
Use this if you are using the FA-66 with an ASIO-compatible application such
as Cubase. In the ASIO settings of your application, choose “EDIROL FA-66.”
You will be able to use ten inputs and ten outputs.
* When using the FA-66 with ASIO, we recommend that you not set your application
to use the Microsoft GS Wavetable SW Synth. (This will decrease the processing
load, and make it easier to change the driver buffer size.)
How WDM ports correspond to FA-66 output jacks
WDM output port
EDIROL FA-66 OUT 1
EDIROL FA-66 OUT 2
EDIROL FA-66 OUT 3
* This port is not displayed when operating at 192 kHz.
L
R
L
R
FA-66 output
jacks
OUTPUT jack 1
OUTPUT jack 2
OUTPUT jack 3
OUTPUT jack 4
Digital output
connector
WDM input port
EDIROL FA-66 IN 1
EDIROL FA-66 IN 2
EDIROL FA-66 IN 3
* This port is not displayed when operating at 192 kHz.
L
R
L
R
FA-66 input
jacks
INPUT jack 1
INPUT jack 2
INPUT jack 3
INPUT jack 4
Digital input
connector
If you have turned on software monitoring in your application,
turn the FA-66’s hardware monitoring (direct monitor) off to
prevent double monitoring and to keep an audio feedback loop
from occurring.
31
FA-66_e.book 32 ページ 2006年1月12日 木曜日 午前11時32分
Installing the driver (Windows)
Input/output device settings
If you will be using the Windows Media Player application
with the FA-66, specify the input/output devices as
follows.
The method in which you make device settings will
depend on the software you are using. For details, refer to
the owner’s manual for your software.
1
Open the Sound, Speech, and Audio Devices
Properties dialog box.
1. From the Windows start menu, choose Control
Panel.
2. In “Pick a category,” click Sound, Speech, and
Depending on your system,
the System icon may be
displayed directly in the
Control Panel (Classic view).
If so, double-click the System
icon.
If you are using sequencer
software, you will need to
make audio and MIDI device
settings from within your
software. For details, refer to
the owner’s manual for the
software you are using.
Audio Devices.
3. In “or Pick a Control Panel icon,” click the Sounds
and Audio Devices icon.
fig.sound
2
3
Click the Audio tab.
In the Sound
playback, Sound
recording, and MIDI
music playback
areas, click the Default
device field. From the
list that appears for
each field, choose the
device shown below.
Sound playback
Sound recording
MIDI music playback
4
If you are using the 192 kHz
sample rate on Windows XP,
the FA-66 may not appear in
the Sounds tab of the Sounds
and Audio Devices Properties
dialog box. If so, please update
your system to Windows XP
Service Pack 1.
EDIROL FA-66 Out 1
EDIROL FA-66 In 1
EDIROL FA-66 MIDI OUT
Click [OK] to close the Sounds and Audio Devices
Properties dialog box.
This completes the audio and MIDI input/output settings.
32
Each input/output device can
only be used by one software
application at a time;
multiclient usage is not
supported.
FA-66_e.book 33 ページ 2006年1月12日 木曜日 午前11時32分
Installing the driver (Windows)
Checking that you hear sound
Now, let’s play back the sample data to verify that the
connections and settings are correct. We will use standard
Windows functionality to play back the sample data
provided on the included CD-ROM.
Before you continue, connect headphones or monitor
speakers to the FA-66 as described in “Basic
connections” (p. 35).
1
2
3
Insert the CD-ROM into the CD-ROM drive of your
computer.
From the SampleSong folder of the CD-ROM, drag
TTears(.mp3) onto your desktop.
Set the FA-66’s sample rate select switch to 48 kHz.
Use of the song data supplied
with this product for any
purpose other than private,
personal enjoyment without
the permission of the
copyright holder is prohibited
by law. Additionally, this data
must not be copied, nor used
in a secondary copyrighted
work without the permission
of the copyright holder.
The contents of the menu that
appears will depend on your
system.
You’ll need to cycle the power to the FA-66 after changing
the sampling rate.
4
Right-click the TTears(.mp3) file you copied, and choose
Play from the menu that appears.
Playback begins.
If the sample data plays correctly, the FA-66 is correctly
connected to your computer, and the driver has also been
installed correctly.
If the volume is too low, or if
you don’t hear sound at all, try
turning the FA-66’s direct
monitor volume knob (p. 12)
so it’s positioned to the left of
the MIX (center) position.
About the demo songs
The SampleSong folder on the included CD-ROM contains the following demo
songs. Please copy the demo songs to the hard disk of your computer before
listening to them.
* The demo songs were produced at 48 kHz. You must set the FA-66’s sample rate to
48 kHz. You’ll need to cycle the power to the FA-66 after changing the sampling rate.
for Cubase folder
This folder contains the demo songs as Cubase VST song files (.all) and Cubase
SX project files (.cpr).
If you are using the Cubase SX demo version, the playback will not be correct
since some functionality (such as effects) will not be available.
for SONAR folder
This folder contains the demo songs as SONAR project files (.cwb).
33
FA-66_e.book 34 ページ 2006年1月12日 木曜日 午前11時32分
Installing the driver (Windows)
Software settings
Before you start up your software, use a FireWire (IEEE
1394) cable to connect the FA-66 to your computer, and
turn on the power of the FA-66.
If your software allows you to specify MIDI and audio
input/output settings, choose EDIROL FA-66. For details,
refer to the owner’s manual for your software. Also refer to
“Software settings” (p. 40).
If you have turned on software
monitoring in your application, turn the
FA-66’s hardware monitoring (direct
monitor) off to prevent double monitoring
and to keep an audio feedback loop from
occurring.
34
For the latest information,
please visit
http://www.edirol.com/
FA-66_e.book 35 ページ 2006年1月12日 木曜日 午前11時32分
Basic connections and settings
This section explains basic connections and data flow for the FA-66.
Refer to the block diagram printed on the front cover of the manual as you read
this section.
* Before making connections to other equipment, turn down the volume of all your
equipment and turn off the power to avoid causing malfunctions or damaging your
speakers.
* When connection cables with resistors are used, the volume level of equipment
connected to the inputs (Input jacks) may be low. If this happens, use connection
cables that do not contain resistors, such as those from the Roland PCS series.
Basic connections
Use a FireWire (IEEE 1394) cable to connect the FA-66 to your computer. MIDI
data and audio data are transferred in both directions via the FireWire (IEEE
1394) cable.
By connecting headphones or monitor speakers as shown in the diagram below,
you can monitor the playback from your software or the sound from an
instrument or audio device connected to the FA-66.
fig.basic
Amplified speakers
FireWire (IEEE1394) connector
IEEE1394 connector (FireWire connector,
iLink connector, DV connector)
FireWire cable
Headphones
Computer
35
FA-66_e.book 36 ページ 2006年1月12日 木曜日 午前11時32分
Basic connections and settings
Recording a mic or guitar
Here’s how to make connections and settings to let you sing or play your guitar
while listening to audio data on your computer, and record just the vocal or
guitar into your sequencer.
fig.mic-guitar
Guitar/bass
Adjust the level
so that the red
(far right) does
not light
Monitor in stereo
Connect to
INPUT 2
Adjust the
input level
Hi-z
Adjust the
input level
Monitor in monaural
Turn the knob toward the
right if you want the sound
from the input jacks to be
louder than the playback
from the computer.
Switch to ON only
if you're using
condenser mics
Specify the
sample rate
When using a mic for
input, it's a good idea to
switch this ON
Turn this all the way
toward the left
Connections
The sound of the mic connected to INPUT 1 will be recorded in your computer
as the left (L) channel. If you connect a source to INPUT 2, it will be recorded on
the right (R) channel.
Connect your guitar to INPUT 2.
Sample rate select switch
Set this to the same sample rate as selected in your recording software.
If you switch the FA-66’s sample rate, you must turn the power of the FA-66 off,
then on again to get the setting to take effect.
Input impedance select switch
If you’ve connected a mic to INPUT 2
Select Lo-Z.
If you’ve connected a guitar to INPUT 2
Select Hi-Z.
STEREO/MONO select switch (direct monitor section)
Set this according to whether you want to monitor the input signal in stereo or
in monaural.
36
FA-66_e.book 37 ページ 2006年1月12日 木曜日 午前11時32分
Basic connections and settings
Direct monitor soft control switch
Turn this on if you want to control input monitoring from ASIO 2.0 compatible
software.
Direct monitor volume
This adjusts the balance between the monitor volume and the audio playback
volume from your computer. Adjusting the direct monitor volume will not
affect the recording level.
Phantom power switch
If you’re using a condenser mic, turn the phantom power switch on.
* If a device that does not use phantom power is connected, you must turn off the
phantom power switch. Failing to do so may cause malfunction.
Input sensitivity knob
Use the input sensitivity knob to adjust the input level. For the best audio
quality, raise the level until it is as high as you can get it without causing the
input level indicator to light in red.
Other notes
Don’t connect anything to jacks you are not using.
Howling could be produced depending on the location of microphones relative
to speakers. This can be remedied by:
1. Changing the orientation of the microphone(s).
2. Relocating microphone(s) at a greater distance from speakers.
3. Lowering volume levels.
37
FA-66_e.book 38 ページ 2006年1月12日 木曜日 午前11時32分
Basic connections and settings
Recording a digital signal
fig.digital
Specify the sample rate
Set this to match the sample rate of
your digital playback device
ON
CD/MD/DAT player,
hard disk recorder, etc.
Connections
Connect your digital device to the digital input connector.
Sample rate select switch
Set this to match the sample rate of your digital playback device and the sample
rate of your recording software.
If you switch the FA-66’s sample rate, you must turn the power of the FA-66 off,
then on again to get the setting to take effect.
You cannot record digital signals if the 192 kHz setting is selected.
Digital input switch
Turn this on so that the FA-66 will synchronize to the digital signal being input
to the digital input connector.
When synchronized correctly, the sync indicator will light green. If this
indicator is blinking green, synchronization has not been achieved. In this case,
check that the sample rate of the connected digital device matches the sample
rate selected by the FA-66’s sample rate switch.
Direct monitor volume
This adjusts the monitor volume.
Adjusting the direct monitor volume will not affect the recording level.
38
FA-66_e.book 39 ページ 2006年1月12日 木曜日 午前11時32分
Basic connections and settings
Connecting various types of equipment
fig.send-return
Guitar/Bass
Amplified speakers
Mixer, DJ Mixer, etc.
Mic
Adjust the level of
the input from a
synthesizer or other
device connected to
the INPUT 1/2 jacks.
FireWire cable
Computer
IEEE1394 connector
(FireWire connector,
iLink connector,
DV connector)
CD/MD/cassette player,
MIDI sound module, etc.
Connections
Connect output jacks 1-4 to your external mixer or other device.
Direct monitor volume
This adjusts the monitor volume.
Adjusting the direct monitor volume will not affect the recording level.
39
FA-66_e.book 40 ページ 2006年1月12日 木曜日 午前11時32分
Software settings
You will need to make audio and MIDI device settings for the software you’re
using. Here are some examples for typical software applications.
SONAR 4
In this example we are using SONAR 4 Producer Edition.
You must make the following settings if you have switched the FA66’s sample rate or have changed the buffer size in the FA-66 Driver
settings dialog box.
1. Power up the FA-66, and then start up SONAR.
2. From SONAR’s Options menu, choose Audio to open the Audio Options
dialog box.
3. Click the Advanced tab.
In the Playback and Recording area, verify that Driver Mode is set to WDM/KS.
* If you change this setting, click [OK] and restart SONAR.
Restart SONAR, and from the Options menu, choose Audio to open the Audio
Options dialog box.
fig.sonar-1.eps
4. In the General tab, set Audio Driver Bit
Depth to 24.
Set the Sampling Rate to the same setting as
the FA-66’s sample rate select switch.
If you change this setting, click [OK] and exit
SONAR.
fig.sonar-4.eps
* If the Audio Driver Error dialog box
appears, click [Use Anyway]. If you click
[Disable], the setting will be discarded.
40
FA-66_e.book 41 ページ 2006年1月12日 木曜日 午前11時32分
Software settings
5. Restart SONAR, and from SONAR’s Options menu, choose Audio to open the
Audio Options dialog box.
6. In the General tab, click Wave Profiler.
When Wave Profiler is finished, click [Close].
fig.sonar-2.eps
7. Click the Drivers tab.
In the lists of Input Drivers and Output
Drivers, click the following devices to
highlight them (white characters on blue
background), and un-highlight all other
devices. Click [OK].
Input devices
EDIROL FA-66 In 1
EDIROL FA-66 In 2
EDIROL FA-66 In 3
Output devices
EDIROL FA-66 Out 1
EDIROL FA-66 Out 2
EDIROL FA-66 Out 3
8. Restart SONAR, and from SONAR’s Options menu, choose Audio to open the
Audio Options dialog box.
fig.sonar-1b.eps
9. In the General tab, make sure that
Playback Timing Master is set to EDIROL
FA-66 OUT, and Record Timing Master is
set to EDIROL FA-66 IN.
fig.sonar-3.eps
10. Click the Driver Profiles tab.
Select EDIROL FA-66 (3 in, 3 out) as the
setting for “Show Profile for,” and then
select “32 bit PCM, left-justified” as the
setting for “Stream > 16 bit data as.”
41
FA-66_e.book 42 ページ 2006年1月12日 木曜日 午前11時32分
Software settings
11. Click [OK] to close the Audio Options dialog box.
12. From SONAR’s Options menu, choose MIDI Devices to open the MIDI
Devices dialog box.
13. In the MIDI Devices dialog box, choose the FA-66 in the Inputs area and the
Outputs area.
fig.sonar-5.eps
14. Restart SONAR.
15. Open the Audio Options dialog box once again as described in step 2.
Verify that the audio device settings are correct.
42
FA-66_e.book 43 ページ 2006年1月12日 木曜日 午前11時32分
Software settings
Digital Performer
In this example we are using Digital Performer 4.5.
fig.digiperf.eps
1. Power up the FA-66, and then start up
Digital Performer.
2. From Digital Performer’s Setup menu,
choose Audio System, and verify that
MOTU Audio System is checked.
3. From the Setup menu, choose Configure
Audio System - Configure Hardware
Driver.
The Configure Hardware Driver dialog
box will appear.
4. In the list, click EDIROL FA-66 to select
it, and then click [OK].
43
FA-66_e.book 44 ページ 2006年1月12日 木曜日 午前11時32分
Software settings
Logic
Here is an example using Logic Pro 7.0.1.
1. Power up the FA-66, and then start up Logic.
2. From the Logic Pro menu, choose Preferences - Audio to open the
Preferences dialog box.
3. Click the Drivers tab.
4. In the Core Audio section, select (add a check mark to) the checkbox located at
the left of Core Audio.
fig.logic.eps
3
4
6
I/O Buffer Size
[Example setting for use at 96 kHz]
As a general guideline, use the following
setting:
PowerPC G4 1 GHz or higher 512
PowerPC G4 1 GHz or lower 1024
Larger Disk Buffer
Check this box if a warning dialog box
such as “Disk is too slow” is displayed.
5. If a dialog box like the following appears, click [Try (Re)Launch].
fig.logic.eps
6. Set Driver to EDIROL FA-66.
7. Close the dialog box.
8. If the Aleart dialog box appears, click [Try (Re)Launch].
44
FA-66_e.book 45 ページ 2006年1月12日 木曜日 午前11時32分
Software settings
Cubase SX/SL
In this example we are using the Macintosh version of Cubase SX Version 2.2.
1. Power up the FA-66, and then start up Cubase.
2. From the Devices menu, choose Device Setup to open the Device Setup
dialog box.
3. In the Devices list at the left side of the dialog box, choose VST Multitrack.
4. Select the Setup tab in the right side of the dialog box.
5. From the drop-down list for ASIO Driver, choose EDIROL FA-66.
6. Click [OK] to close the Device Setup dialog box.
fig.cubase-1.eps
If you experience clicks or pops in the sound, click [Expert] to open the VST
Engine Expert Settings dialog box. Setting the Audio Priority to “Very High”
may reduce clicks and pops.
fig.cubase-2.eps
45
FA-66_e.book 46 ページ 2006年1月12日 木曜日 午前11時32分
Software settings
FA-66 Driver Settings dialog box
(Windows)
There is no FA-66 Driver Settings dialog box on Macintosh. Make
settings from within your software.
You can adjust the audio latency by changing the FA-66 driver settings.
Decreasing the buffer size will shorten the latency.
Increasing the buffer size may eliminate problems such as clicks or pops in the
sound.
* Latency is the time delay from when the software plays back audio data until sound
is actual heard from an audio device such as the FA-66.
Here’s how to adjust the buffer size.
1. Close any software that is using the FA-66.
2. From the Windows start menu, choose Control Panel.
3. Click “Switch to Classic View” to select the Classic view.
Depending on your system, the Classic view may already be selected. If so,
proceed to the next step.
fig.control-icon.eps
4. In the Control Panel, double-click the EDIROL FA-66 icon.
The EDIROL FA-66 Driver settings dialog box will appear.
fig.control.eps
5. Set WDM and ASIO to Normal.
6. Move the Buffer Size slider to the far left (Min).
If clicks or pops occur with the current setting,
move the slider one step toward the right from its
current value.
7. Click [OK] to close the dialog box.
8. Turn the power of the FA-66 off, then on again.
At this time, be sure to close all software before
you turn the FA-66’s power off.
* If you power of the FA-66 off while using your software, it may not operate correctly.
46
FA-66_e.book 47 ページ 2006年1月12日 木曜日 午前11時32分
Software settings
9. Re-start the software that is using the FA-66.
If your software includes a function for testing audio devices, execute the test
function after re-starting the software.
* Settings are not applied until you restart your software.
10. Play back audio data on your software.
If you hear clicks or pops, close the software, and repeat steps 4-10 until you no
longer hear clicks or pops.
This completes the basic settings.
fig.control2.eps
If you are using WDM or ASIO compatible
software, and you still experience clicks or pops
in the sound even after making the above setting,
or if you want to make the latency even shorter,
you can change the settings from the pulldown
menu.
WDM
When using the FA-66 with the following software
• Conventional software such as Media Player
• When using an application such as SONAR in WDM driver mode
• When using DirectSound software
Normal
normal size
Smaller
smaller buffer than Normal (shorter latency)
ASIO
When using the FA-66 with ASIO-compatible software such as Cubase
• Conventional software such as Media Player
• When using an application such as SONAR in WDM driver mode
• When using DirectSound software
Normal
normal size
Smaller
smaller buffer than Normal (shorter latency)
Larger
larger buffer than Normal (if clicks or pops occur)
If you still experience clicks or pops even though you have specified the largest
buffer size, check Use Maximum Buffer Setting. If this item is checked, the
slider and the settings of the WDM and ASIO items will be ignored, and an even
larger buffer size will be used.
If you still experience clicks or pops even after doing this, the problem may lie
elsewhere. Please refer to the Troubleshooting section.
* Depending on your software, there may also be a buffer size and latency adjustment
in the audio settings of your software. For details, refer to the owner’s manual for
your software.
47
FA-66_e.book 48 ページ 2006年1月12日 木曜日 午前11時32分
Troubleshooting
If you experience problems, read this chapter first/ It contains tips for solving most
problems.
Driver-related problems (Windows)
Can’t install the driver correctly
You attempted to install as described in “Installing the driver,” but did
not succeed.
Install the FA-66 driver once again as described in “Installing the driver
(Windows)” (p. 24). Also check the Device Manager to see whether “Other device,”
“Unknown device,” “?,” “!,” or “x” is shown for any device. If you see such a device,
delete it.
Does the Device Manager show “Other device,” “Unknown device,” or
any device marked with “?,” “!,” or “x”?
If driver installation did not end successfully, the installed driver may remain in an
incomplete state.
Install the FA-66 driver once again as described in “Installing the driver
(Windows)” (p. 24).
Is the FA-66 connected correctly?
Make sure that you have used a FireWire (IEEE 1394) cable to correctly connect the
FA-66 to the FireWire (IEEE 1394) connector of your computer.
Is the FA-66 powered up?
Make sure that the FA-66’s power is on. Make sure that the POWER switch is on.
Could the FA-66’s power switch be set to BUS?
Even if you normally use the FA-66 on bus power, you should connect the AC
adaptor and set the power switch to the DC IN position while installing the driver
(so that the power supply does not become unstable).
Could other FireWire (IEEE 1394) devices be connected?
When installing, all FireWire (IEEE 1394) devices other than the FA-66 should be
disconnected from your computer.
If you have connected the FA-66 to an external FireWire (IEEE 1394) hard disk,
please connect the FA-66 directly to an IEEE 1394 connector (FireWire connector,
iLink connector, DV connector) on the computer itself.
Could other applications or resident software (such as an anti-virus
program) be running?
Installation may not occur correctly if other programs are running. Be sure to close
all other programs before installing.
48
FA-66_e.book 49 ページ 2006年1月12日 木曜日 午前11時32分
Troubleshooting
Are you attempting to install from a networked CD-ROM drive?
You cannot install from a networked CD-ROM drive.
Could the CD-ROM or the lens of your CD-ROM drive be dirty?
If the CD-ROM or the lens of your CD-ROM drive are dirty, the installer may not
work correctly. Use a commercially available CD cleaner or lens cleaner to clean the
CD-ROM and/or lens.
Are the power conservation settings of your computer turned off?
If power conservation settings are turned on for your computer, disable these
settings. (For details on how to disable them, refer to the owner’s manual of your
computer.)
Is there enough free space on your hard disk?
Delete unneeded files to increase the amount of free space.
After deleting the file(s), empty the recycling bin.
Is the FireWire (IEEE 1394) connector enabled on your computer?
Refer to the owner’s manual for your computer, and verify that the FireWire (IEEE
1394) connector of your computer is enabled. The driver cannot be installed unless
the FireWire (IEEE 1394) connector is enabled.
Does your computer or FireWire (IEEE 1394) repeater hub have a
sufficient power supply?
If you are using bus power, the FA-66 cannot be connected if insufficient power is
being supplied to it.
Check whether the following cases might apply.
• If you are using a notebook computer running on its battery, operation may be
unstable with some computers. If this is the case, connect your computer to its
AC adaptor.
• The power conservation mode of your computer may be limiting the power it
supplies to the FireWire (IEEE 1394) connector. Re-examine the settings of your
computer.
• The FA-66 cannot be used with some bus-powered repeater hubs (hubs that do
not have their own power supply). Use a self-powered hub (a repeater hub that
has its own power supply).
Does your computer meet the FireWire (IEEE 1394) specification?
Operation may be unstable if you are using a computer that does not electrically
meet the FireWire (IEEE 1394) specification. If so, you may be able to solve the
problem by connecting a FireWire (IEEE 1394) repeater hub that has its own power
supply.
49
FA-66_e.book 50 ページ 2006年1月12日 木曜日 午前11時32分
Troubleshooting
Can’t install/uninstall the driver
Did you log onto Windows as a user with administrative privileges?
In order to install/uninstall/reinstall the FA-66 driver in Windows, you must log
onto Windows as a user with administrative privileges, such as Administrator.
Did you make the “Driver Signing Options” setting?
You must set “Driver Signing Options” in order to install/reinstall the driver.
(p. 24)
Windows displays an “Installing Hardware,” “Did not find digital signature”
dialog box.
Did you make the “Driver Signing Options” setting?
You must set “Driver Signing Options” in order to install/reinstall the driver.
(p. 24)
The “Welcome to the Found New Hardware Wizard” dialog box appears
even though you installed the driver.
Did you connect the FA-66 to a different FireWire (IEEE 1394) connector
than the one you used when installing the driver?
If your computer or FireWire (IEEE 1394) hub has two or more FireWire (IEEE 1394)
connectors, and you connect the FA-66 to a FireWire (IEEE 1394) connector to which
you have not previously connected it, this dialog box may appear even though you
have already installed the driver. (This is not a malfunction.)
Install the FA-66 driver once again as described in “Installing the driver
(Windows)” (p. 24).
50
FA-66_e.book 51 ページ 2006年1月12日 木曜日 午前11時32分
Troubleshooting
No sound
Can’t record or play back audio or MIDI
No sound
Are the volume controls of the FA-66 set appropriately?
Adjust the output volume knob and direct monitor volume of the FA-66’s front
panel.
Is your audio playback system (e.g., stereo) connected correctly?
Make sure that the FA-66’s output jacks are correctly connected using audio cables
to the input jacks of your audio playback system. For details on connections, refer
to “Basic connections” (p. 35).
Did you connect/disconnect the FireWire (IEEE 1394) cable or cycle the
power to the FA-66 while your software was running?
You must close all software that uses the FA-66 before powering off the FA-66.
If you start up your computer with the FA-66 connected, operation may become
unstable for some computers.
In this case, connect the FA-66 after starting up your computer.
Could your computer have entered Standby (Suspend) or Sleep mode?
After your computer wakes up, close all software that had been using the FA-66,
and then cycle the power to the FA-66.
Have you specified the audio and MIDI data output destination in the
operating system?
Depending on the software you are using, you may need to specify the FA-66 as the
audio data output destination for your computer. For details on this setting, refer to
“Audio and MIDI settings” (p. 19) or “Driver settings” (p. 30).
Is the driver installed correctly?
If you’re using Windows, you’ll need to install a driver in order to play back audio/
MIDI data via the FA-66. For details on installation and settings, refer to “Installing
the driver (Windows)” (p. 24).
Are you running numerous software programs?
An error message may appear if numerous software programs are running
simultaneously. If this occurs, close the software you are not using.
In Windows, a program is still running if it remains in the taskbar even after you
close its window; close any unneeded software shown in the taskbar.
51
FA-66_e.book 52 ページ 2006年1月12日 木曜日 午前11時32分
Troubleshooting
Is the FA-66’s sample rate set to a rate other than 192 kHz?
If the FA-66’s sample rate select switch is set to 192 kHz, the digital output
connector and the digital input connector are not available.
Are your input/output devices connected correctly?
In order to play back audio/MIDI using the FA-66, you must make the appropriate
input/output device settings. For details on making these settings, refer to “Audio
and MIDI settings” (p. 19) or “Driver settings” (p. 30).
If you are using the 192 kHz sample rate on Windows XP, the FA-66 may not appear
in the Sounds tab of the Sounds and Audio Devices Properties dialog box. If so,
please update your system to Windows XP Service Pack 1.
Could the FA-66 have been connected when you started up the computer?
Start up the computer with the FA-66 disconnected, and then connect the FA-66.
Depending on the type of computer you are using, starting up the computer when
the FA-66 is already connected may cause operation to be unstable. In this case, start
up your computer and then connect the FA-66.
52
FA-66_e.book 53 ページ 2006年1月12日 木曜日 午前11時32分
Troubleshooting
A device connected to the input jacks can’t be heard through headphones
Are the input sensitivity knobs and direct monitor volume knob set
appropriately?
Turn the knobs toward the right to adjust the volume.
Is the output volume knob raised appropriately?
Turn the knob toward the right to adjust the volume.
Sounds from the computer are not heard from the FA-66
Have you specified the audio data output destination in your playback
software?
You need to make settings in your software to select the FA-66 as the destination for
the output of audio data. For details on how to make this setting, refer to the
owner’s manual for the software you are using.
Could your computer have entered Standby (Suspend) mode or Sleep
mode?
In this case, after your computer wakes up, close all software that had been using
the FA-66, and then cycle the power to the FA-66.
If this does not solve the problem, close your software and then restart your
computer.
We also recommend that you set your computer so that it does not enter Sleep
mode.
Recording produces a silent file
Did you specify the correct audio data input source within the operating
system?
Depending on the software you are using, you may need to specify the FA-66 as the
audio data input source for your computer. For details on this setting, refer to
“Audio settings” (p. 19) or “Driver settings” (p. 30).
53
FA-66_e.book 54 ページ 2006年1月12日 木曜日 午前11時32分
Troubleshooting
Can’t record from a digital connection
When capturing audio data from a CD or MD into your computer, is the
digital input switch “on”?
Turn on the digital input switch.
Does the sample rate of your software match the sample rate of the
digital audio device connected to the digital in connector?
Set the sample rate to the same setting.
If you switch the FA-66’s sample rate, you must turn the power of the FA-66 off,
then on again to get the setting to take effect.
Can’t play/record 24-bit audio data
Does your software support 24-bit audio data?
You will need to use software that supports 24-bit audio data.
Is your software set to record/play 24-bit audio data?
Set your software to 24-bit.
54
FA-66_e.book 55 ページ 2006年1月12日 木曜日 午前11時32分
Troubleshooting
Noise or pops are heard when recording/
playing on your computer
Noise is heard during audio playback
Pops/clicks occur during audio playback
Noise is heard in the recorded sound
In Windows, did you make the setting described in “Giving priority to
background services”?
In order to ensure that audio/MIDI processing occurs smoothly, make the setting
described in “Giving priority to background services.”
(➔ “Giving priority to background services” (p. 29))
In Macintosh, check the Energy Saver settings.
In the Mac OS System Setup, set Energy Saver as follows.
fig.power-save2
Click the Sleep tab.
Set “Put the computer to sleep when it
is inactive for:” to Never.
Set “Put the display to sleep when the
computer is inactive for:” to Never.
fig.power-save1
Click the Options tab.
If there is a Processor Performance
setting, set it to Highest.
55
FA-66_e.book 56 ページ 2006年1月12日 木曜日 午前11時32分
Troubleshooting
In Windows, Power Management settings in the Control Panel may
cause clicks or pops to occur in the audio playback.
The power management properties that appear when you double-click Power
Management will differ depending on your computer system. The explanation that
follows is for a typical situation, but you should refer to the owner’s manual for
your computer to verify these settings.
Some computers may not have the following items.
1. In the Windows Control Panel, double-click the System icon. The
System Properties dialog box will appear.
2. Click the Hardware tab.
3. Click Device Manager to see the list of devices.
4. From the list, choose Advanced Power Management Support, and click
Properties.
The Advanced Power Management Support Properties dialog box will
appear.
5. Click the Settings tab, and in Troubleshooting, check the “Don’t Poll
Power Supply Status” check box. Then click [OK].
6. In the System Properties dialog box, click [OK].
7. Restart Windows.
Could two or more computers be connected to the FA-66 or to your
mixer or audio devices?
Try connecting the FA-66 to only one computer. Check whether the noise
disappears when the FA-66 is connected to only one computer. Connecting
numerous audio devices to a computer may produce noise in some situations. If this
occurs, connect only the FA-66 to your computer.
Are you using a FireWire (IEEE 1394) device in addition to the FA-66?
Try switching off FireWire (IEEE 1394) audio devices other than the FA-66.
If you have connected the FA-66 to an external FireWire (IEEE 1394) hard disk,
please connect the FA-66 directly to an IEEE 1394 connector (FireWire connector,
iLink connector, DV connector) on the computer itself.
In Windows, you may be able to solve the problem by adjusting the
buffer size in the FA-66 Driver Settings dialog box.
Adjust the buffer size as described in “FA-66 Driver Settings dialog box
(Windows)” (p. 46).
After changing the buffer size, you must restart any software that uses the FA-66. If
your software has an audio device test function, execute the test function.
56
FA-66_e.book 57 ページ 2006年1月12日 木曜日 午前11時32分
Troubleshooting
Use the Windows Device Manager to disable the 1394 Net Adaptor.
1. In the Windows Control Panel, double-click the System icon. The System
Properties dialog box will appear.
2. Click the Hardware tab.
3. Click Device Manager to see the list of devices.
4. In the list, double-click Network Adapters.
The 1394 Net Adaptor will appear.
5. Double-click 1394 Net Adapter.
The 1394 Net Adaptor Properties dialog box will appear.
6. In Device Usage, choose “Do not use this device (disable).”
7. Click [OK].
8. Close the Device Manager.
9. In the System Properties dialog box, click [OK] to close the dialog box.
Are numerous software programs running?
Playback may be interrupted if numerous software programs are running at the
same time, or when you start up another software program. Close any unneeded
software, and try again. If this does not solve the problem, try restarting your
computer.
Clicks or pops may occur in the sound if a LAN is operating.
Try disabling the LAN in the Device Manager. If this eliminates the clicks or pops,
you may be able to solve the problem by updating your LAN driver or BIOS.
Is the sample rate setting in your software the same as the FA-66’s
sample rate select switch setting?
Set your software and the FA-66 to the same sample rate.
If you switch the FA-66’s sample rate, you must turn the power of the FA-66 off,
then on again to get the setting to take effect.
Try adding memory.
Adding memory will improve the processing capability of your computer. For
details on how to add memory, refer to the owner’s manual of your computer.
If you are using a Macintosh, try pressing the FA-66’s digital input
switch.
Even if you aren’t making use of digital input/output, problems with noise and
sound dropout can sometimes be alleviated by switching the FA-66’s digital input
switch on and off.
57
FA-66_e.book 58 ページ 2006年1月12日 木曜日 午前11時32分
Troubleshooting
Did you start up your Macintosh before connecting the FA-66?
If you’re using Mac OS, operation may become unstable if you first connected the
FA-66 to your Macintosh via a FireWire (IEEE 1394) cable and then started up your
Macintosh.
You must start up your Macintosh first, and then connect the FA-66.
Is the FA-66 connected to a FireWire (IEEE 1394) hub?
Try connecting the FA-66 directly to the FireWire (IEEE 1394) connector of your
computer itself.
Noise may be entering via the line inputs or mic inputs.
If a MIDI sound module with a FireWire (IEEE 1394) connector is connected via
FireWire (IEEE 1394) to the same computer as the FA-66, and the output of the MIDI
sound module is connected to the input jacks of the FA-66, noise from the computer
may be heard via the MIDI sound module from the FA-66. In this case, you can
either connect the MIDI sound module and FA-66 in parallel via a self-powered
hub, or connect the MIDI sound module in series or via a MIDI interface.
Playback/recording stops midway, and subsequent playback/recording is
not possible
While you were using the FA-66, could your computer have performed a
task with a heavy processing load, such as accessing a CD-ROM drive or
network?
If a heavy processing load occurs while the FA-66 is being used, it may not work
correctly. In this case, stop playback/recording, and then start playback/recording
once again. If you are still unable to play/record correctly, close all software that
had been using the FA-66, and re-connect the FA-66.
Digitally recorded sound has distortion, the wrong pitch, or contains noise
Is the sample rate setting in your software the same as the sample rate
of the digital device connected to the digital input connector?
Set your software and the FA-66 to the same sample rate.
If you switch the FA-66’s sample rate, you must turn the power of the FA-66 off,
then on again to get the setting to take effect.
58
FA-66_e.book 59 ページ 2006年1月12日 木曜日 午前11時32分
Troubleshooting
Noise or distortion occurs when the FA-66
is not connected to your computer
The sound is too weak
Noise is heard in the sound
Has a mic or guitar been left connected?
If a mic or guitar is connected to the FA-66, disconnect the mic or guitar and turn
the input sensitivity knob all the way toward the left (lowering the input level).
Have you connected the grounding terminal?
Connecting the chassis of your computer or the grounding terminal of your
computer’s AC power cord to an electrical ground may solve the problem. Also,
make sure that a device that produces a strong magnetic field, such as a television
or microwave oven, is not located nearby.
Could numerous audio devices be connected?
Noise may occur if numerous audio devices are connected. Do not connect audio
devices you are not using.
Sound is distorted
Is the output level indicator lit red?
If you are inputting sound via the combo input jacks, use the FA-66’s input
sensitivity knobs to lower the input level.
Sound of a device connected to the input jacks is distorted
Insufficient volume from a device connected to the audio input/output
jacks
Is the input level appropriate?
If you are inputting audio via input jacks 3 and 4, use the FA-66’s input level
adjustment knob (rear panel) to adjust the input level. If you are inputting audio via
the combo input jacks, use the input sensitivity knobs (front panel) to adjust the
input level.
If you are inputting audio via the INPUT2 combo input jack, check the setting of the
input impedance select switch.
Is the direct monitor volume set appropriately?
Adjust the volume as described in Direct Monitor Volume (p. 12).
59
FA-66_e.book 60 ページ 2006年1月12日 木曜日 午前11時32分
Troubleshooting
A substantial amount of noise is present in the guitar sound
Does the noise decrease when you turn down the volume of your guitar?
If the noise decreases when you turn down the volume of your guitar, the guitar
pickup may be affected by noise from your computer or display. Try locating the
guitar as far away from the computer as possible.
Insufficient volume from your guitar
Are you using the correct jack?
Connect your guitar to the INPUT 2 combo input jack.
Is the input impedance select switch set correctly?
Set the input impedance select switch to Hi-Z.
Insufficient volume from a mic
Is the input level appropriate?
Turn the input sensitivity knob toward the right to adjust the input volume.
60
FA-66_e.book 61 ページ 2006年1月12日 木曜日 午前11時32分
Troubleshooting
Others
Can’t start the Cubase
The first time you use the FA-66 with Cubase, turn on the power with the
FA-66’s sample rate select switch at the 44.1 kHz position.
If this switch is not set to 44.1 kHz, it may be impossible to start Cubase.
61
FA-66_e.book 62 ページ 2006年1月12日 木曜日 午前11時32分
Main specifications
● Number of Audio Record/Playback Channels
<44.1/48/96 kHz>
Record:
6 channels
Playback: 6 channels
(Full duplex)
<192 kHz>
Record:
4 channels
Playback: 4 channels
(Full duplex)
* Depending on the computer you are using, you may be unable to obtain sufficient
performance.
● Signal Processing
PC interface:24 bits
AD/DA Conversion:24 bits (linear)
● Sampling Frequency
Digital output:44.1/48/96 kHz
Digital input:44.1/48/96 kHz
AD/DA Conversion:44.1/48/96/192 kHz
● Frequency Response
96.0 kHz:
48.0 kHz:
44.1 kHz:
20 Hz to 40 kHz (+0/-2 dB)
20 Hz to 22 kHz (+0/-2 dB)
20 Hz to 20 kHz (+0/-2 dB)
● Nominal Input Level
Input Jack 1–2 (XLR type):-50 to -10 dBu
Input Jack 1–2 (1/4 inch TRS phone type):-35 to +4 dBu
Input Jack 3–4:
-10 dBu to +13 dBu (balanced)
● Nominal Output Level
Output Jack 1–4: +4 dBu (balanced)
● Residual Noise Level
(input terminated with 1 k ohms, MAIN VOLUME: 0 dB, INPUT SENS: +4 dBu,
DIRECT MONITOR VOLUME: OUT1/2 position, IHF-A typ., Balanced)
Output Jack 1–2:
-95 dBu
● S/N RATIO (Typical)
OUTPUT: 105 dB (typ.)
INPUT:
102 dB (typ.)
62
FA-66_e.book 63 ページ 2006年1月12日 木曜日 午前11時32分
Main specifications
● Interface
Firewire (IEEE1394)
Digital input/output
Optical type (conforms to IEC60958)
MIDI IN/OUT
● Connectors
<Front Panel>
Input Jack 1–2 (XLR type / 1/4 inch TRS phone type)
XLR type (balanced / phantom power +48 V)
1/4 inch TRS phone type (balanced)
* Input jack 2 supports high impedance
Headphones Jack (Stereo 1/4 inch phone type)
<Rear Panel>
Input Jack 3–4 (RCA pin type)
Output Jack 1–4 (1/4 inch TRS phone type (balanced))
Digital In Connector (Optical type)
Digital Out Connector (Optical type)
MIDI Connectors (In, Out)
FireWire Connectors (6 pins type, 4 pins type)
● Power Supply
DC 9 V (AC adaptor)
* FireWire Bus Power
● Current Draw
650 mA
● Dimensions
164 (W) x 148 (D) x 44 (H) mm
6-1/2 (W) x 5-7/8 (D) x 1-3/4 (H) inches
● Weight
0.65 kg / 1 lb 7 oz
● Accessories
Owner’s Manual
CD-ROM
AC Adaptor
FireWire cable (6 pins to 6 pins, 6 pins to 4 pins)
(0 dBu = 0.775 V rms)
* In the interest of product improvement, the specifications and/or appearance of this unit
are subject to change without prior notice.
63
FA-66_e.book 64 ページ 2006年1月12日 木曜日 午前11時32分
Index
Numerics
I
4-pin connector ................................................... 15
4-pin type ............................................................ 14
6-pin connector ................................................... 15
6-pin type ............................................................ 14
Input impedance select switch .................. 10, 36
Input jacks .......................................................... 17
Input level adjustment knob ........................... 17
Input sensitivity knob ....................................... 37
Input sensitivity knobs ..................................... 10
A
AC adaptor jack .................................................. 15
ASIO ............................................................... 30–31
Audio input device ............................................ 30
Audio MIDI Setup ............................................. 21
Audio output device .......................................... 30
B
BUS ....................................................................... 14
C
Combo input jacks ............................................. 10
Cubase ................................................................. 45
D
Digital input connector ..................................... 17
Digital input switch ..................................... 11, 38
Digital output connector ................................... 16
Digital Performer ............................................... 43
direct monitor mixer section ............................ 12
direct monitor section ........................................ 12
Direct monitor soft control switch ............. 12, 37
Direct monitor volume .......................... 12, 37–39
L
Limiter switch .................................................... 16
Logic .................................................................... 44
M
Mac OS ................................................................
Main output jacks ..............................................
MIDI ....................................................................
MIDI IN ..............................................................
MIDI IN/OUT connectors ...............................
MIDI music playback .......................................
MIDI OUT ..........................................................
18
16
30
30
16
32
30
O
optical ........................................................... 16–17
Output indicator ................................................ 11
Output jacks ....................................................... 16
Output volume .................................................. 13
P
EDIROL FA-66 Driver settings ........................ 46
Peak/Limiter indicator .................................... 11
Phantom power switch .............................. 16, 37
Power indicator ................................................. 11
Power switch ..................................................... 14
F
S
E
FireWire (IEEE 1394) cables ................................ 8
FireWire (IEEE 1394) connectors ..................... 15
G
Grounding terminal ........................................... 14
H
Headphone jack .................................................. 13
Sample rate select switch ..................... 15, 36, 38
SONAR ............................................................... 40
Sound playback ................................................. 32
Sound recording ................................................ 32
STEREO/MONO select switch ................. 12, 36
Sync indicator .................................................... 11
W
WDM ............................................................. 30–31
Windows ............................................................ 24
64
FA-66_e.book 65 ページ 2006年1月12日 木曜日 午前11時32分
MEMO
FA-66_e.book 66 ページ 2006年1月12日 木曜日 午前11時32分
MEMO
FA-66_e.book 67 ページ 2006年1月12日 木曜日 午前11時32分
MEMO
FA-66_e.book 68 ページ 2006年1月12日 木曜日 午前11時32分
Information
EUROPE
When you need repair service, call your nearest EDIROL/Roland Service Center or authorized
EDIROL/Roland distributor in your country as shown below.
HONG KONG
BARBADOS
PERU
IRELAND
CYPRUS
Parsons Music Ltd.
8th Floor, Railway Plaza, 39
Chatham Road South, T.S.T,
Kowloon, HONG KONG
TEL: 2333 1863
A&B Music Supplies LTD
12 Webster Industrial Park
Wildey, St.Michael, Barbados
TEL: (246)430-1100
Audionet
Distribuciones Musicales SAC
Juan Fanning 530
Miraflores
Lima - Peru
TEL: (511) 4461388
Roland Ireland
G2 Calmount Park, Calmount
Avenue, Dublin 12
Republic of IRELAND
TEL: (01) 4294444
Radex Sound Equipment Ltd.
17, Diagorou Street, Nicosia,
CYPRUS
TEL: (022) 66-9426
EDIROL (Europe) Ltd.
Studio 3.4 114 Power Road
London W4 5PY
U. K.
TEL: +44 (0)20 8747 5949
FAX:+44 (0)20 8747 5948
http://www.edirol.com/europe
INDIA
Deutschland
TEL: 0700 33 47 65 20
France
TEL: 0810 000 371
Italia
TEL: 02 93778329
INDONESIA
BRAZIL
Roland Brasil Ltda.
Rua San Jose, 780 Sala B
Parque Industrial San Jose
Cotia - Sao Paulo - SP, BRAZIL
TEL: (011) 4615 5666
Rivera Digitec (India) Pvt. Ltd.
409, Nirman Kendra
Mahalaxmi Flats Compound
Off. Dr. Edwin Moses Road,
Mumbai-400011, INDIA
TEL: (022) 2493 9051
CHILE
Comercial Fancy II S.A.
Rut.: 96.919.420-1
Nataniel Cox #739, 4th Floor
Santiago - Centro, CHILE
TEL: (02) 688-9540
PT Citra IntiRama
J1. Cideng Timur No. 15J-150
Jakarta Pusat
INDONESIA
TEL: (021) 6324170
NORTH AMERICA
CANADA
Centro Musical Ltda.
Cra 43 B No 25 A 41 Bododega 9
Medellin, Colombia
TEL: (574)3812529
Roland Canada Music Ltd.
(Head Office)
5480 Parkwood Way Richmond
B. C., V6V 2M4 CANADA
TEL: (604) 270 6626
Roland Canada Music Ltd.
(Toronto Office)
170 Admiral Boulevard
Mississauga On L5T 2N6
CANADA
TEL: (905) 362 9707
U. S. A.
Roland Corporation U.S.
5100 S. Eastern Avenue
Los Angeles, CA 90040-2938,
U. S. A.
TEL: (323) 890 3700
AFRICA
Cosmos Corporation
1461-9, Seocho-Dong,
Seocho Ku, Seoul, KOREA
TEL: (02) 3486-8855
CURACAO
MALAYSIA/
SINGAPORE
Roland Asia Pacific Sdn. Bhd.
45-1, Block C2, Jalan PJU 1/39,
Dataran Prima, 47301 Petaling
Jaya, Selangor, MALAYSIA
TEL: (03) 7805-3263
PHILIPPINES
G.A. Yupangco & Co. Inc.
339 Gil J. Puyat Avenue
Makati, Metro Manila 1200,
PHILIPPINES
TEL: (02) 899 9801
ROLAND TAIWAN
ENTERPRISE CO., LTD.
Room 5, 9fl. No. 112 Chung
Shan N.Road Sec.2, Taipei,
TAIWAN, R.O.C.
TEL: (02) 2561 3339
Theera Music Co. , Ltd.
330 Soi Verng NakornKasem,
New Road, Sumpantawongse,
Bangkok 10100, THAILAND
TEL: (02) 224-8821
SOUTH AFRICA
Paul Bothner(PTY)Ltd.
Royal Cape Park, Unit 24
Londonderry Road, Ottery 7800
Cape Town, SOUTH AFRICA
TEL: (021) 799 4900
ASIA
CHINA
Roland Shanghai Electronics
Co.,Ltd.
5F. No.1500 Pingliang Road
Shanghai 200090, CHINA
TEL: (021) 5580-0800
Roland Shanghai Electronics
Co.,Ltd.
(BEIJING OFFICE)
10F. No.18 3 Section Anhuaxili
Chaoyang District Beijing
100011 CHINA
TEL: (010) 6426-5050
Roland Shanghai Electronics
Co.,Ltd.
(GUANGZHOU OFFICE)
2/F., No.30 Si You Nan Er Jie
Yi Xiang, Wu Yang Xin Cheng,
Guangzhou 510600, CHINA
TEL: (020) 8736-0428
VIETNAM
SAIGON MUSIC
DISTRIBUTOR
(TAN DINH MUSIC)
138 Tran Quang Khai Street
Dist. 1, Ho Chi Minh City
VIETNAM
TEL: (08) 848-4068
Roland Elektronische
Musikinstrumente HmbH.
Austrian Office
Eduard-Bodem-Gasse 8,
A-6020 Innsbruck, AUSTRIA
TEL: (0512) 26 44 260
MX MUSIC SP.Z.O.O.
UL. Gibraltarska 4.
PL-03664 Warszawa POLAND
TEL: (022) 679 44 19
MUSIC HOUSE CO. LTD.
FREDDY FOR MUSIC
P. O. Box 922846
Amman 11192 JORDAN
TEL: (06) 5692696
PORTUGAL
KUWAIT
Roland Iberia, S.L.
Portugal Office
Cais das Pedras, 8/9-1 Dto
4050-465, Porto, PORTUGAL
TEL: 22 608 00 60
EASA HUSAIN AL-YOUSIFI
& SONS CO.
Abdullah Salem Street,
Safat, KUWAIT
TEL: 243-6399
ROMANIA
LEBANON
FBS LINES
Piata Libertatii 1,
535500 Gheorgheni,
ROMANIA
TEL: (266) 364 609
Chahine S.A.L.
Gerge Zeidan St., Chahine
Bldg., Achrafieh, P.O.Box: 165857
Beirut, LEBANON
TEL: (01) 20-1441
RUSSIA
MuTek
Dorozhnaya ul.3,korp.6
117 545 Moscow, RUSSIA
TEL: (095) 981-4967
HONDURAS
CZECH REP.
SWEDEN
Almacen Pajaro Azul S.A. de C.V.
BO.Paz Barahona
3 Ave.11 Calle S.O
San Pedro Sula, Honduras
TEL: (504) 553-2029
K-AUDIO
Kardasovska 626.
CZ-198 00 Praha 9,
CZECH REP.
TEL: (2) 666 10529
Roland Scandinavia A/S
SWEDISH SALES OFFICE
Danvik Center 28, 2 tr.
S-131 30 Nacka SWEDEN
TEL: (0)8 702 00 20
MARTINIQUE
DENMARK
SWITZERLAND
Musique & Son
Z.I.Les Mangle
97232 Le Lamantin
Martinique F.W.I.
TEL: 596 596 426860
Roland Scandinavia A/S
Nordhavnsvej 7, Postbox 880,
DK-2100 Copenhagen
DENMARK
TEL: 3916 6200
Roland (Switzerland) AG
Landstrasse 5, Postfach,
CH-4452 Itingen,
SWITZERLAND
TEL: (061) 927-8383
FINLAND
UKRAINE
Roland Scandinavia As, Filial
Finland
Elannontie 5
FIN-01510 Vantaa, FINLAND
TEL: (0)9 68 24 020
TIC-TAC
Mira Str. 19/108
P.O. Box 180
295400 Munkachevo,
UKRAINE
TEL: (03131) 414-40
NICARAGUA
GERMANY
MIDDLE EAST
QATAR
Badie Studio & Stores
P.O. Box 62,
Doha, QATAR
TEL: 423554
SAUDI ARABIA
aDawliah Universal
Electronics APL
Corniche Road, Aldossary
Bldg., 1st Floor, Alkhobar,
SAUDI ARABIA
P.O.Box 2154, Alkhobar 31952
SAUDI ARABIA
TEL: (03) 898 2081
SYRIA
ZUHAL DIS TICARET A.S.
Galip Dede Cad. No.37
Beyoglu - Istanbul / TURKEY
TEL: (0212) 249 85 10
U.A.E.
Zak Electronics & Musical
Instruments Co. L.L.C.
Zabeel Road, Al Sherooq Bldg.,
No. 14, Grand Floor, Dubai,
U.A.E.
TEL: (04) 3360715
Moon Stores
No.16, Bab Al Bahrain Avenue,
P.O.Box 247, Manama 304,
State of BAHRAIN
TEL: 17 211 005
Roland East Europe Ltd.
Warehouse Area ‘DEPO’ Pf.83
H-2046 Torokbalint,
HUNGARY
ARGENTINA
TALENTZ CENTRE L.L.C.
Malatan House No.1
Al Noor Street, Ruwi
SULTANATE OF OMAN
TEL: 2478 3443
BAHRAIN
HUNGARY
CENTRAL/LATIN
AMERICA
OMAN
TURKEY
Roland (U.K.) Ltd.
Atlantic Close, Swansea
Enterprise Park, SWANSEA
SA7 9FJ,
UNITED KINGDOM
TEL: (01792) 702701
STOLLAS S.A.
Music Sound Light
155, New National Road
Patras 26442, GREECE
TEL: 2610 435400
JORDAN
Technical Light & Sound
Center
Rawda, Abdul Qader Jazairi St.
Bldg. No. 21, P.O.BOX 13520,
Damascus, SYRIA
TEL: (011) 223-5384
UNITED KINGDOM
Roland Elektronische
Musikinstrumente HmbH.
Oststrasse 96, 22844
Norderstedt, GERMANY
TEL: (040) 52 60090
GREECE
Bansbach Instrumentos
Musicales Nicaragua
Altamira D'Este Calle Principal
de la Farmacia 5ta.Avenida
1 Cuadra al Lago.#503
Managua, Nicaragua
TEL: (505)277-2557
For Australia
Tel: (02) 9982 8266
For New Zealand
Tel: (09) 3098 715
EUROPE
AUSTRIA
POLAND
Roland Iberia, S.L.
Paseo García Faria, 33-35
08005 Barcelona SPAIN
TEL: 93 493 91 00
Casa Veerkamp, s.a. de c.v.
Av. Toluca No. 323, Col. Olivar
de los Padres 01780 Mexico
D.F. MEXICO
TEL: (55) 5668-6699
38 Campbell Avenue
Dee Why West. NSW 2099
AUSTRALIA
Instrumentos Musicales
Allegro,C.A.
Av.las industrias edf.Guitar
import
#7 zona Industrial de Turumo
Caracas, Venezuela
TEL: (212) 244-1122
ISRAEL
Halilit P. Greenspoon & Sons
Ltd.
8 Retzif Ha’aliya Hashnya St.
Tel-Aviv-Yafo ISRAEL
TEL: (03) 6823666
SPAIN
MEXICO
AUSTRALIA/
NEW ZEALAND
Roland Corporation
Australia Pty.,Ltd.
VENEZUELA
MOCO INC.
No.41 Nike St., Dr.Shariyati Ave.,
Roberoye Cerahe Mirdamad
Tehran, IRAN
TEL: (021) 285-4169
Roland Scandinavia Avd.
Kontor Norge
Lilleakerveien 2 Postboks 95
Lilleaker N-0216 Oslo
NORWAY
TEL: 2273 0074
Roland Central Europe N.V.
Houtstraat 3, B-2260, Oevel
(Westerlo) BELGIUM
TEL: (014) 575811
Gigamusic SARL
10 Rte De La Folie
97200 Fort De France
Martinique F.W.I.
TEL: 596 596 715222
AUSTRALIA/
NEW ZEALAND
Todo Musica S.A.
Francisco Acuna de Figueroa 1771
C.P.: 11.800
Montevideo, URUGUAY
TEL: (02) 924-2335
IRAN
NORWAY
BELGIUM/FRANCE/
HOLLAND/
LUXEMBOURG
Casa Instrumental
Calzada Roosevelt 34-01,zona 11
Ciudad de Guatemala
Guatemala
TEL:(502) 599-2888
Al Fanny Trading Office
9, EBN Hagar A1 Askalany
Street,
ARD E1 Golf, Heliopolis,
Cairo 11341, EGYPT
TEL: 20-2-417-1828
Maison FO - YAM Marcel
25 Rue Jules Hermann,
Chaudron - BP79 97 491
Ste Clotilde Cedex,
REUNION ISLAND
TEL: (0262) 218-429
Instrumentos Fernando Giraldez
Calle Proyecto Central No.3
Ens.La Esperilla
Santo Domingo,
Dominican Republic
TEL:(809) 683 0305
GUATEMALA
THAILAND
AMR Ltd
Ground Floor
Maritime Plaza
Barataria Trinidad W.I.
TEL: (868)638 6385
DOMINICAN REPUBLIC
Mas Musika
Rumichaca 822 y Zaruma
Guayaquil - Ecuador
TEL:(593-4)2302364
EGYPT
REUNION
Zeelandia Music Center Inc.
Orionweg 30
Curacao, Netherland Antilles
TEL:(305)5926866
ECUADOR
TAIWAN
Roland Italy S. p. A.
Viale delle Industrie 8,
20020 Arese, Milano, ITALY
TEL: (02) 937-78300
URUGUAY
COLOMBIA
KOREA
ITALY
TRINIDAD
TEL: (23) 511011
Instrumentos Musicales S.A.
Av.Santa Fe 2055
(1123) Buenos Aires
ARGENTINA
TEL: (011) 4508-2700
As of December 10, 2005 (EDIROL-1)
*
0
3
8
9
0
6
3
4
-
0
2
*
03890634
’06-1-2N
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement