Village QV36B Owner's Manual

R
Owner’s Manual
Installation and Operation
Models:
QV32B-A
QV36B-A
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury, or death.
• DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer’s instructions
and the manufactured home construction and safety standard,
Title 24 CFR, Part 3280 or Standard for Installation in Mobile
Homes, CAN/CSA Z240MH, in Canada.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
• Leave this manual with
party responsible for use
and operation.
D
DI O N
SC OT
AR
D
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other flammable
materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fitter.
See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.
Installation and service of this appliance should be
performed by qualified personnel. Hearth & Home
Technologies suggests NFI certified or factory trained
professionals, or technicians supervised by an NFI
certified professional.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
1
Read this manual before installing or operating this appliance.
Please retain this owner’s manual for future reference.
A. Congratulations
This owner’s manual should be retained for future
reference. We suggest that you keep it with your other
important documents and product manuals.
Congratulations on selecting a Quadra-Fire gas fireplace, an
elegant and clean alternative to wood burning fireplaces. The
Quadra-Fire gas fireplace you have selected is designed to
provide the utmost in safety, reliability, and efficiency.
The information contained in this owner’s manual, unless
noted otherwise, applies to all models and gas control
systems.
As the owner of a new fireplace, you’ll want to read and
carefully follow all of the instructions contained in this
owner’s manual. Pay special attention to all cautions and
warnings.
Your new Quadra-Fire gas fireplace will give you years of
durable use and trouble-free enjoyment. Welcome to the
Quadra-Fire family of fireplace products!
We recommend that you record the following pertinent
information about your fireplace.
Homeowner Reference Information
Model Name: ___________________________________________ Date purchased/installed: __________________
Serial Number:__________________________________________ Location on fireplace: _____________________
Dealership purchased from: _______________________________ Dealer Phone: __________________________
Notes: _______________________________________________________________________________________
_____________________________________________________________________________________________
Listing Label Information/Location
The model information regarding your specific fireplace can be found on
the rating plate usually located in the control area of the fireplace.
R
Type of Gas
.
Quadra-Fire, a brand of Hearth & Home Technologies, Inc.
7571 215th Street West, Lakeville, MN 55044
Not for use with solid fuel.
(Ne doit pas entre utilise avec un combustible solide).
Type of Gas (Sorte De Gaz):
NATURAL GAS
This appliance must be installed in accordance with local codes, if any; if not, follow ANSI Z223.1
in the USA or CAN/CGA B149 installation codes. (Installer l’appareil selon les codes ou reglements
locaux ou, en l’absence de tels reglements, selon les codes d’installation CAN/CGA-B149.)
ANSI Z21XX-XXXX · CSA 2.XX-MXX · UL307B
Gas and Electric
Information
Minimum Permissible Gas Supply for Purposes of Input Adjustment.
Approved Minimum (De Gaz) Acceptable
0.0 in w.c.
(Po. Col. d’eau)
Maximum Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Maximum Manifold Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Minimum Manifold Pressure (Pression)
0.0 in w.c.
(Po. Col. d’eau)
Total Electrical Requirements: 000Vac, 00Hz., less than 00 Amperes
ALTITUDE:
MAX. INPUT BTUH:
MIN. INPUT BTUH:
ORIFICE SIZE:
2
0-0000 FT.
00,000
00,000
#XXXXX
IN CANADA
0000-0000FT.
00,000
00,000
#XXXXX
Model Number
MADE IN USA
Model:
(Modele):
XXXXXXXX
Serial
(Serie):
XXXXXXXX
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
Serial Number
Safety Alert Key:
•
•
•
•
DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE: Used to address practices not related to personal injury.
Table of Contents
A. Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
B. Limited Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1 Listing and Code Approvals
A.
B.
C.
D.
E.
F.
G.
H.
Appliance Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tempered Glass Specifications . . . . . . . . . . . . . . . . . . . . .
BTU Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . . .
Non-Combustible Materials Specification. . . . . . . . . . . . . .
Combustible Materials Specification . . . . . . . . . . . . . . . . .
Electrical Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Requirements for the Commonwealth of Massachusetts . .
7
7
7
7
7
7
7
8
User Guide
Gas Fireplace Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Your Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Fan Kit (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Clear Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Decorative Doors and Fronts . . . . . . . . . . . . . . . . . . . . . . 10
Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Remote Controls, Wall Controls and Wall Switches . . . . . 10
Before Lighting Fireplace . . . . . . . . . . . . . . . . . . . . . . . . . 10
Lighting Instructions (Standing Pilot) . . . . . . . . . . . . . . . . 11
After Fireplace is Lit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . 12
3 Maintenance and Service
A. Maintenance Tasks-Homeowner . . . . . . . . . . . . . . . . . . . 13
B. Maintenance Tasks-Qualified Service Technician . . . . . . 14
Installer Guide
Typical Appliance System. . . . . . . . . . . . . . . . . . . . . . . . .
Design and Installation Considerations . . . . . . . . . . . . . .
Tools and Supplies Needed . . . . . . . . . . . . . . . . . . . . . . .
Inspect Appliance and Components . . . . . . . . . . . . . . . . .
15
16
16
16
22
22
22
22
23
24
8 Vent Clearances and Framing
A.
B.
C.
D.
Pipe Clearances to Combustibles . . . . . . . . . . . . . . . . . .
Wall Penetration Framing . . . . . . . . . . . . . . . . . . . . . . . . .
Install the Ceiling Firestop . . . . . . . . . . . . . . . . . . . . . . . .
Install Attic Insulation Shield . . . . . . . . . . . . . . . . . . . . . . .
36
36
37
38
A. Top Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
B. Rear Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
C. Securing and Leveling the Appliance . . . . . . . . . . . . . . . . 41
10 Installing Vent Pipe (DVP and SLP Pipe)
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
Assemble Vent Sections (DVP Pipe Only) . . . . . . . . . . . .
Assemble Vent Sections (SLP Pipe Only) . . . . . . . . . . . .
Assemble Slip Sections . . . . . . . . . . . . . . . . . . . . . . . . . .
Secure the Vent Sections . . . . . . . . . . . . . . . . . . . . . . . . .
Disassemble Vent Sections . . . . . . . . . . . . . . . . . . . . . . .
Install Decorative Ceiling Components (SLP only). . . . . .
Install Metal Roof Flashing . . . . . . . . . . . . . . . . . . . . . . . .
Assemble and Install Storm Collar . . . . . . . . . . . . . . . . . .
Install Vertical Termination Cap . . . . . . . . . . . . . . . . . . . .
Install Decorative Wall Components (SLP only) . . . . . . . .
Heat Shield Requirements for Horizontal Termination . . .
Install Horizontal Termination Cap (DVP and SLP Pipe) .
42
43
43
44
44
45
46
46
47
47
47
48
A.
B.
C.
D.
Fuel Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Altitude Installations . . . . . . . . . . . . . . . . . . . . . . . . .
49
49
49
49
12 Electrical Information
5 Framing and Clearances
A.
B.
C.
D.
Approved Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vent Table Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use of Elbows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Measuring Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Use of Flex Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vent Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 Gas Information
4 Getting Started
A.
B.
C.
D.
A.
B.
C.
D.
E.
F.
9 Appliance Preparation
2 Operating Instructions
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
7 Vent Information and Diagrams
Selecting Appliance Location . . . . . . . . . . . . . . . . . . . . . .
Constructing the Appliance Chase . . . . . . . . . . . . . . . . . .
Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . .
17
18
18
19
6 Termination Locations
A.
B.
C.
D.
E.
F.
Wiring Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standing Pilot Ignition System Wiring . . . . . . . . . . . . . . .
Optional Accessories Requirements . . . . . . . . . . . . . . . .
Electrical Service and Repair . . . . . . . . . . . . . . . . . . . . . .
Junction Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . .
Wall Switch Installation for Fan (Optional) . . . . . . . . . . . .
50
50
50
50
51
51
 A. Vent Termination Minimum Clearances . . . . . . . . . . . . . . 20
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
3
13 Finishing
A. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 52
B. Facing Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
14 Appliance Setup
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
Remove Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . .
Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . .
Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ember Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Install the Log Assembly. . . . . . . . . . . . . . . . . . . . . . . . . .
Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . .
Install the Mesh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Install Trim and/or Surround . . . . . . . . . . . . . . . . . . . . . . .
Install Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air Shutter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
54
54
54
54
54
55
57
57
57
57
57
15 Troubleshooting
A. Standing Pilot Ignition System . . . . . . . . . . . . . . . . . . . . . 58
16 Reference Materials
A.
B.
 C.
D.
Appliance Dimension Diagram . . . . . . . . . . . . . . . . . . . . .
Vent Components Diagrams . . . . . . . . . . . . . . . . . . . . . .
Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
60
61
67
72
 = Contains updated information.
4
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
B. Limited Lifetime Warranty
Hearth & Home Technologies Inc.
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for
HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty
is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table.
The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.
Warranty Period
Parts
Labor
1 Year
2 years
HHT Manufactured Appliances and Venting
Gas
X
X
Wood
X
X
X
3 years
Pellet
EPA
Wood
Coal
X
X
X
X
X
X
X
X
X
Components Covered
Electric Venting
X
X
All parts and material except as
covered by Conditions,
Exclusions, and Limitations
listed
Igniters, electronic components,
and glass
Factory-installed blowers
Molded refractory panels
X
Firepots and burnpots
5 years
1 year
7 years
3 years
10
years
1 year
X
Limited
3 years
Lifetime
X
X
X
X
X
90 Days
X
X
X
X
X
X
X
X
Castings and baffles
X
X
Manifold tubes,
HHT chimney and termination
Burners, logs and refractory
Firebox and heat exchanger
X
X
All replacement parts
beyond warranty period
See conditions, exclusions, and limitations on next page.
4021-645C 12-29-10
Page 1 of 2
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
5
B. Limited Lifetime Warranty (continued)
WARRANTY CONDITIONS:
‡
‡
‡
‡
7KLVZDUUDQW\RQO\FRYHUV++7DSSOLDQFHVWKDWDUHSXUFKDVHGWKURXJKDQ++7DXWKRUL]HGGHDOHURUGLVWULEXWRU$OLVWRI
++7DXWKRUL]HGGHDOHUVLVDYDLODEOHRQWKH++7EUDQGHGZHEVLWHV
7KLVZDUUDQW\LVRQO\YDOLGZKLOHWKH++7DSSOLDQFHUHPDLQVDWWKHVLWHRIRULJLQDOLQVWDOODWLRQ
&RQWDFW\RXULQVWDOOLQJGHDOHUIRUZDUUDQW\VHUYLFH,IWKHLQVWDOOLQJGHDOHULVXQDEOHWRSURYLGHQHFHVVDU\SDUWVFRQWDFW
WKHQHDUHVW++7DXWKRUL]HGGHDOHURUVXSSOLHU$GGLWLRQDOVHUYLFHIHHVPD\DSSO\LI\RXDUHVHHNLQJZDUUDQW\VHUYLFH
IURPDGHDOHURWKHUWKDQWKHGHDOHUIURPZKRP\RXRULJLQDOO\SXUFKDVHGWKHSURGXFW
&KHFNZLWK\RXUGHDOHULQDGYDQFHIRUDQ\FRVWVWR\RXZKHQDUUDQJLQJDZDUUDQW\FDOO7UDYHODQGVKLSSLQJFKDUJHV
IRUSDUWVDUHQRWFRYHUHGE\WKLVZDUUDQW\
WARRANTY EXCLUSIONS:
7KLVZDUUDQW\GRHVQRWFRYHUWKHIROORZLQJ
‡ &KDQJHVLQVXUIDFHILQLVKHVDVDUHVXOWRIQRUPDOXVH$VDKHDWLQJDSSOLDQFHVRPHFKDQJHVLQFRORURILQWHULRUDQG
H[WHULRUVXUIDFHILQLVKHVPD\RFFXU7KLVLVQRWDIODZDQGLVQRWFRYHUHGXQGHUZDUUDQW\
‡ 'DPDJHWRSULQWHGSODWHGRUHQDPHOHGVXUIDFHVFDXVHGE\ILQJHUSULQWVDFFLGHQWVPLVXVHVFUDWFKHVPHOWHGLWHPV
RURWKHUH[WHUQDOVRXUFHVDQGUHVLGXHVOHIWRQWKHSODWHGVXUIDFHVIURPWKHXVHRIDEUDVLYHFOHDQHUVRUSROLVKHV
‡ 5HSDLURUUHSODFHPHQWRISDUWVWKDWDUHVXEMHFWWRQRUPDOZHDUDQGWHDUGXULQJWKHZDUUDQW\SHULRG7KHVHSDUWV
LQFOXGHSDLQWZRRGSHOOHWDQGFRDOJDVNHWVILUHEULFNVJUDWHVIODPHJXLGHVOLJKWEXOEVEDWWHULHVDQGWKHGLVFRORUDWLRQRIJODVV
‡ 0LQRUH[SDQVLRQFRQWUDFWLRQRUPRYHPHQWRIFHUWDLQSDUWVFDXVLQJQRLVH7KHVHFRQGLWLRQVDUHQRUPDODQGFRPSODLQWVUHODWHGWRWKLVQRLVHDUHQRWFRYHUHGE\WKLVZDUUDQW\
‡ 'DPDJHVUHVXOWLQJIURPIDLOXUHWRLQVWDOORSHUDWHRUPDLQWDLQWKHDSSOLDQFHLQDFFRUGDQFHZLWKWKHLQVWDOODWLRQ
LQVWUXFWLRQVRSHUDWLQJLQVWUXFWLRQVDQGOLVWLQJDJHQWLGHQWLILFDWLRQODEHOIXUQLVKHGZLWKWKHDSSOLDQFHIDLOXUHWR
LQVWDOOWKHDSSOLDQFHLQDFFRUGDQFHZLWKORFDOEXLOGLQJFRGHVVKLSSLQJRULPSURSHUKDQGOLQJLPSURSHURSHUDWLRQDEXVHPLVXVHFRQWLQXHGRSHUDWLRQZLWKGDPDJHGFRUURGHGRUIDLOHGFRPSRQHQWVDFFLGHQWRULPSURSHUO\
LQFRUUHFWO\SHUIRUPHGUHSDLUVHQYLURQPHQWDOFRQGLWLRQVLQDGHTXDWHYHQWLODWLRQQHJDWLYHSUHVVXUHRUGUDIWLQJ
FDXVHGE\WLJKWO\VHDOHGFRQVWUXFWLRQVLQVXIILFLHQWPDNHXSDLUVXSSO\RUKDQGOLQJGHYLFHVVXFKDVH[KDXVWIDQVRU
IRUFHGDLUIXUQDFHVRURWKHUVXFKFDXVHVXVHRIIXHOVRWKHUWKDQWKRVHVSHFLILHGLQWKHRSHUDWLQJLQVWUXFWLRQV
LQVWDOODWLRQRUXVHRIFRPSRQHQWVQRWVXSSOLHGZLWKWKHDSSOLDQFHRUDQ\RWKHUFRPSRQHQWVQRWH[SUHVVO\DXWKRUL]HG
DQGDSSURYHGE\++7PRGLILFDWLRQRIWKHDSSOLDQFHQRWH[SUHVVO\DXWKRUL]HGDQGDSSURYHGE\++7LQZULWLQJ
DQGRULQWHUUXSWLRQVRUIOXFWXDWLRQVRIHOHFWULFDOSRZHUVXSSO\WRWKHDSSOLDQFH
‡ 1RQ++7YHQWLQJFRPSRQHQWVKHDUWKFRPSRQHQWVRURWKHUDFFHVVRULHVXVHGLQFRQMXQFWLRQZLWKWKHDSSOLDQFH
‡ $Q\SDUWRIDSUHH[LVWLQJILUHSODFHV\VWHPLQZKLFKDQLQVHUWRUDGHFRUDWLYHJDVDSSOLDQFHLVLQVWDOOHG
‡ ++7¶VREOLJDWLRQXQGHUWKLVZDUUDQW\GRHVQRWH[WHQGWRWKHDSSOLDQFH¶VFDSDELOLW\WRKHDWWKHGHVLUHGVSDFH,QIRUPDWLRQLVSURYLGHGWRDVVLVWWKHFRQVXPHUDQGWKHGHDOHULQVHOHFWLQJWKHSURSHUDSSOLDQFHIRUWKHDSSOLFDWLRQ&RQVLGHUDWLRQPXVWEHJLYHQWRDSSOLDQFHORFDWLRQDQGFRQILJXUDWLRQHQYLURQPHQWDOFRQGLWLRQVLQVXODWLRQDQGDLUWLJKWQHVVRI
WKHVWUXFWXUH
This warranty is void if:
‡
‡
‡
7KHDSSOLDQFHKDVEHHQRYHUILUHGRURSHUDWHGLQDWPRVSKHUHVFRQWDPLQDWHGE\FKORULQHIOXRULQHRURWKHUGDPDJLQJ
FKHPLFDOV2YHUILULQJFDQEHLGHQWLILHGE\EXWQRWOLPLWHGWRZDUSHGSODWHVRUWXEHVUXVWFRORUHGFDVWLURQEXEEOLQJ
FUDFNLQJDQGGLVFRORUDWLRQRIVWHHORUHQDPHOILQLVKHV
7KHDSSOLDQFHLVVXEMHFWHGWRSURORQJHGSHULRGVRIGDPSQHVVRUFRQGHQVDWLRQ
7KHUHLVDQ\GDPDJHWRWKHDSSOLDQFHRURWKHUFRPSRQHQWVGXHWRZDWHURUZHDWKHUGDPDJHZKLFKLVWKHUHVXOWRIEXW
QRWOLPLWHGWRLPSURSHUFKLPQH\RUYHQWLQJLQVWDOODWLRQ
LIMITATIONS OF LIABILITY:
‡
7KHRZQHU¶VH[FOXVLYHUHPHG\DQG++7¶VVROHREOLJDWLRQXQGHUWKLVZDUUDQW\XQGHUDQ\RWKHUZDUUDQW\H[SUHVVRU
LPSOLHGRULQFRQWUDFWWRUWRURWKHUZLVHVKDOOEHOLPLWHGWRUHSODFHPHQWUHSDLURUUHIXQGDVVSHFLILHGDERYH,QQR
HYHQWZLOO++7EHOLDEOHIRUDQ\LQFLGHQWDORUFRQVHTXHQWLDOGDPDJHVFDXVHGE\GHIHFWVLQWKHDSSOLDQFH6RPHVWDWHV
GRQRWDOORZH[FOXVLRQVRUOLPLWDWLRQRILQFLGHQWDORUFRQVHTXHQWLDOGDPDJHVVRWKHVHOLPLWDWLRQVPD\QRWDSSO\WR\RX
7KLVZDUUDQW\JLYHV\RXVSHFLILFULJKWV\RXPD\DOVRKDYHRWKHUULJKWVZKLFKYDU\IURPVWDWHWRVWDWH(;&(3772
7+((;7(173529,'('%</$:++70$.(612(;35(66:$55$17,(627+(57+$17+(:$55$17<
63(&,),('+(5(,17+('85$7,212)$1<,03/,(':$55$17<,6/,0,7('72'85$7,212)7+(
(;35(66(':$55$17<63(&,),('$%29(
4021-645C 12-29-10
6
Page 2 of 2
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
1
Listing and Code Approvals
A. Appliance Certification
C. BTU Specifications
Models
MODELS: QV32B-A, QV36B-A
LABORATORY: Underwriters Laboratories, Inc. (UL)
TYPE: Direct Vent Gas Fireplace Heater
U.S. (0-2000 ft.) or Canada (2000-4500 ft.)
QV32B-A (NG)
This product is listed to ANSI standards for “Vented Gas
Appliance Heaters” and applicable sections of “Gas Burning Heating Appliances for Manufactured Homes and
Recreational Vehicles”, and “Gas Fired Appliances for
Use at High Altitudes”.
NOTICE: This installation must conform with local codes.
In the absence of local codes you must comply with the
National Fuel Gas Code, ANSI Z223.1-latest edition in
the U.S.A. and the CAN/CGA B149 Installation Codes in
Canada.
QV36B-A (NG)
QV36B-A (LP)
Minimum
Input
BTU/h
Orifice
Size (DMS)
US
28,000 17,000
38
CANADA
25,200 15,300
39
STANDARD: ANSI Z21.88-2005 • CSA2.33-2005
QV32B-A (LP)
Maximum
Input
BTU/h
US
26,300 15,000 1.55 mm
CANADA
23,670 13,500
53
US
30,000 20,500
36
CANADA
27,000 18,450
37
US
28,000 15,800
52
CANADA
25,200 14,220
53
D. High Altitude Installations
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
When installing above 2000 feet elevation:
NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.
This appliance is tested and approved as either supplemental room heat or as a decorative appliance. It should not be
factored as primary heat in residential heating calculations.
B. Tempered Glass Specifications
Hearth & Home Technologies appliances manufactured
with tempered glass may be installed in hazardous locations such as bathtub enclosures as defined by the Consumer Product Safety Commission (CPSC). The tempered
glass has been tested and certified to the requirements
of ANSI Z97.1 and CPSC 16 CFR 1202 (Safety Glazing
Certification Council SGCC# 1595 and 1597. Architectural Testing, Inc. Reports 02-31919.01 and 02-31917.01).
This statement is in compliance with CPSC 16 CFR Section 1201.5 “Certification and labeling requirements”
which refers to 15 U.S. Code (USC) 2063 stating “…Such
certificate shall accompany the product or shall otherwise
be furnished to any distributor or retailer to whom the
product is delivered.”
Some local building codes require the use of tempered
glass with permanent marking in such locations. Glass
meeting this requirement is available from the factory.
Please contact your dealer or distributor to order.
• In the USA: Reduce input rate 4% for each 1000 feet
above 2000 feet.
• In CANADA: Reduce input rate 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.
Check with your local gas utility to determine proper
orifice size.
E. Non-Combustible Materials Specification
Material which will not ignite and burn. Such materials are
those consisting entirely of steel, iron, brick, tile, concrete,
slate, glass or plasters, or any combination thereof.
Materials that are reported as passing ASTM E 136,
Standard Test Method for Behavior of Materials in a
Vertical Tube Furnace at 750 ºC and UL763 shall be
considered non-combustible materials.
F. Combustible Materials Specification
Materials made of or surfaced with wood, compressed paper, plant fibers, plastics, or other material that can ignite
and burn, whether flame proofed or not, or plastered or
unplastered shall be considered combustible materials.
G. Electrical Codes
NOTICE: This appliance must be electrically wired
and grounded in accordance with local codes or, in the
absence of local codes, with National Electric Code
ANSI/NFPA 70-latest edition or the Canadian Electric
Code CSA C22.1.
• A 110-120 VAC circuit for this product must be protected with ground-fault circuit-interrupter protection,
in compliance with the applicable electrical codes,
when it is installed in locations such as in bathrooms
or near sinks.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
7
Note: The following requirements reference various
Massachusetts and national codes not contained in this
document.
H. Requirements for the Commonwealth of
Massachusetts
For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in
whole or in part for residential purposes, including those
owned or operated by the Commonwealth and where the
side wall exhaust vent termination is less than seven (7)
feet above finished grade in the area of the venting, including but not limited to decks and porches, the following
requirements shall be satisfied:
Installation of Carbon Monoxide Detectors
At the time of installation of the side wall horizontal vented
gas fueled equipment, the installing plumber or gas fitter
shall observe that a hard wired carbon monoxide detector
with an alarm and battery back-up is installed on the floor
level where the gas equipment is to be installed. In addition, the installing plumber or gas fitter shall observe that
a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of
the dwelling, building or structure served by the side wall
horizontal vented gas fueled equipment. It shall be the
responsibility of the property owner to secure the services
of qualified licensed professionals for the installation of
hard wired carbon monoxide detectors.
In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic,
the hard wired carbon monoxide detector with alarm and
battery back-up may be installed on the next adjacent
floor level.
In the event that the requirements of this subdivision can
not be met at the time of completion of installation, the
owner shall have a period of thirty (30) days to comply
with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
Approved Carbon Monoxide Detectors
Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA
720 and be ANSI/UL 2034 listed and IAS certified.
Signage
A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with the
exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read,
in print size no less than one-half (1/2) in. in size, “GAS
VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
Inspection
The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed
in accordance with the provisions of 248 CMR 5.08(2)(a)1
through 4.
Exemptions
The following equipment is exempt from 248 CMR
5.08(2)(a)1 through 4:
• The equipment listed in Chapter 10 entitled “Equipment
Not Required To Be Vented” in the most current edition
of NFPA 54 as adopted by the Board; and
• Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate
from the dwelling, building or structure used in whole or
in part for residential purposes.
MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall
horizontally vented gas equipment provides a venting
system design or venting system components with the
equipment, the instructions provided by the manufacturer
for installation of the equipment and the venting system
shall include:
• Detailed instructions for the installation of the venting
system design or the venting system components; and
• A complete parts list for the venting system design or
venting system.
Gas Equipment Venting System NOT Provided
When the manufacturer of a Product Approved side wall
horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
“special venting systems”, the following requirements
shall be satisfied by the manufacturer:
• The referenced “special venting system” instructions
shall be included with the appliance or equipment installation instructions; and
• The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation
instructions.
A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting
instructions, and/or all venting design instructions shall
remain with the appliance or equipment at the completion
of the installation.
See Gas Connection section for additional Commonwealth of Massachusetts requirements.
8
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
2
Operating Instructions
User Guide
• Keep remote controls out of reach of children.
A. Gas Fireplace Safety
• Never leave children alone near a hot fireplace, whether
operating or cooling down.
WARNING
• Teach children to NEVER touch the fireplace.
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
• Consider not using the fireplace when children will be
present.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
Contact your dealer for more information, or visit: www.
hpba.org/safety-information.
To prevent unintended operation when not using your fireplace for an extended period of time (summer months,
vacations, trips, etc):
• Remove batteries from remote controls.
High temperatures may ignite clothing or other
flammable materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
• Turn off wall controls.
• Turn off gas controls valve on standing pilot models.
When lighting the pilot light on fireplaces with a standing
pilot, remove the fixed glass assembly so you can detect presence of residual gas build-up. See Standing Pilot
Lighting instructions and Maintenance Tasks.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
B. Your Fireplace
If you expect that small children or vulnerable adults may
come into contact with this fireplace, the following precautions are recommended:
WARNING! DO NOT operate fireplace before reading and understanding operating instructions. Failure
to operate fireplace according to operating instructions
could cause fire or injury.
• Install a physical barrier such as:
- A decorative firescreen.
- Adjustable safety gate.
• Install a switch lock or a wall/remote control with child
protection lockout feature.
DECORATIVE DOORS
(NOT SHOWN)
SECTION 2.E.
FIXED GLASS ASSEMBLY
(NOT SHOWN)
SECTION 14.G.
GRATE
SECTION 2.B.
MANTEL
FAN KIT
SECTION 2.C
HEARTH
CLEAR SPACE
SECTION 2.D.
Figure 2.1 General Operating Parts
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
9
C. Fan Kit (optional)
F. Fixed Glass Assembly
If desired, a fan kit may be added. Contact your dealer to
order the correct fan kit.
See Section 14.G.
D. Clear Space
G. Remote Controls, Wall Controls and Wall
Switches
WARNING! DO NOT place combustible objects in front
of the fireplace or block louvers. High temperatures may
start a fire. See Figure 2.2.
Follow the instructions supplied with the control installed
to operate your fireplace:
Avoid placing candles and other heat-sensitive objects on
mantel or hearth. Heat may damage these objects.
For safety:
• Install a switch lock or a wall/remote control with child
protection lockout feature.
• Keep remote controls out of reach of children.
See your dealer if you have questions.
H. Before Lighting Fireplace
Before operating this fireplace for the first time, have a
qualified service technician:
• Verify all shipping materials have been removed from
inside and/or underneath the firebox.
• Review proper placement of logs, ember material and/or
other decorative materials.
• Check the wiring.
3F
T.
IN CLE
FR AR
ON S
T O PAC
FF E
IR
EP
• Check the air shutter adjustment.
• Ensure that there are no gas leaks.
LA
CE
• Ensure that the glass is sealed and in the proper position
and that the integral barrier is in place.
WARNING! Risk of Fire or Asphyxiation! DO NOT operate fireplace with fixed glass assembly removed.
Figure 2.2 Clear Space
E. Decorative Doors and Fronts
WARNING! Risk of Fire! Install ONLY doors or fronts
approved by Hearth & Home Technologies. Unapproved
doors or fronts may cause fireplace to overheat.
This fireplace has been supplied with an integral
barrier to prevent direct contact with the fixed glass
panel. DO NOT operate the fireplace with the barrier
removed.
Contact your dealer or Hearth & Home Technologies if
the barrier is not present or help is needed to properly
install one.
For more information refer to the instructions supplied with
your decorative door or front.
10
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
I. Lighting Instructions (Standing Pilot)
FOR YOUR SAFETY
READ BEFORE LIGHTING
LIGHTING
INSTRUCTIONS
1. Open control access panel.
WARNING: If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
A. This appliance has a pilot which
must be lighted by hand. When
lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING, smell all around
the appliance area for gas. Be sure to
smell next to the floor because some
gas is heavier than air and will settle
on the floor.
WHAT TO DO IF YOU SMELL GAS
• DO NOT try to light any appliance.
• DO NOT touch any electric switch; do
not use any phone in your building.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or
turn the gas control knob. Never use
tools. If the knob will not push in or
turn by hand, DO NOT try to repair
it, call a qualified service technician.
Force or attempted repair may result in a fire or explosion.
D. DO NOT use this appliance if any
part has been under water. Immediately call a qualified service technician to inspect the appliance and
to replace any part of the control
system and any gas control which
has been under water.
WARNING:
CAUTION:
DO NOT CONNECT 110 VAC TO
THE CONTROL VALVE.
Hot while in operation. DO NOT touch.
Keep children, clothing, furniture, gasoline and other liquids having flammable
vapors away.
Improper installation, adjustment, alteration, service or maintenance can
cause injury or property damage. Refer to the owner’s information manual
provided with this appliance.
This appliance needs fresh air for
safe operation and must be installed
so there are provisions for adequate
combustion and ventilation air.
If not installed, operated, and maintained in accordance with the manufacturer’s instructions, this product
could expose you to substances in fuel
or fuel combustion which are known to
the State of California to cause cancer, birth defects, or other reproductive
harm.
Keep burner and control compartment
clean. See installation and operating
instructions accompanying appliance.
DO NOT operate the appliance with
fixed glass assembly removed, cracked
or broken. Replacement of the fixed
glass assembly should be done by a
licensed or qualified service person.
NOT FOR USE
WITH SOLID FUEL
For use with natural gas and propane.
A conversion kit, as supplied by the
manufacturer, shall be used to convert
this appliance to the alternate fuel.
2. Turn off all electric power to
the appliance.
3. Push in gas control knob
slightly and turn clockwise
to “OFF”.
Note: Knob cannot be turned from “PILOT” to “OFF”
unless knob is pushed in slightly. DO NOT force.
4. Open the fixed glass assembly. You may need to
remove the decorative front.
5. Wait five (5) minutes to clear out any gas. Then
smell for gas, including near the floor. If you smell
gas, STOP! Follow “B” in the Safety
Information located on the left side
of this label. If you don’t smell gas,
go to next step.
6. Find the pilot. The pilot is inside
combustion chamber next to the
main burner
7. Turn knob on gas control counterclockwise
to “PILOT”.
8. Push in control knob all the way and hold in. Immediately depress red or black piezo button. It may require
several depressions of the red or black piezo button
until PILOT lights. If PILOT light does not light after
10 seconds, return to step 3. Continue to hold the
control knob in for about one minute after the pilot is
lit. Release knob and it will pop back out. Pilot should
remain lit. If it goes out, repeat steps 3 through 6.
• If knob does not pop up when released, stop and
immediately call your service technician or gas
supplier.
• If the pilot will not stay lit after several tries, turn
the gas control knob to “OFF” and call your service technician or gas supplier.
9. Reinstall fixed glass assembly. Reinstall decorative
front.
10. Turn gas control knob counterclockwise
to “ON”. Close access panel.
11. Turn on all electric power to the appliance.
12. To light burner, turn the wall control or on/off switch
to “ON”.
Also Certified for Installation in a
Bedroom or a Bedsitting Room.
TO TURN OFF
GAS TO APPLIANCE
For assistance or additional information, consult a qualified installer, service agency or the gas supplier.
1. Turn off all electric power to the appliance if service is to be performed.
For additional information on operating your
Hearth & Home Technologies fireplace, please refer to www.fireplaces.com.
2. Open control access panel.
3. Move switch to “OFF” position.
4. Push in gas control knob slightly and turn clockwise
to OFF”. DO NOT force.
5. Close control access panel.
Final inspection by
464-903H
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
11
J. After Fireplace is Lit
Initial Break-in Procedure
• The fireplace should be run three to four hours
continuously on high.
• Turn the fireplace off and allow it to completely cool.
• Remove fixed glass assembly. See Section 14.G.
• Clean fixed glass assembly. See Section 3.
• Replace the fixed glass assembly and run continuously
on high an additional 12 hours.
This cures the materials used to manufacture the fireplace.
NOTICE! Open windows for air circulation during fireplace break-in.
• Some people may be sensitive to smoke and odors.
• Smoke detectors may activate.
K. Frequently Asked Questions
ISSUE
SOLUTIONS
Condensation on the glass
This is a result of gas combustion and temperature variations. As the appliance warms, this
condensation will disappear.
Blue flames
This is a result of normal operation and the flames will begin to yellow as the appliance is allowed to burn for 20 to 40 minutes.
Odor from appliance
When first operated, this appliance may release an odor for the first several hours. This is caused
by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may
also be released from finishing materials and adhesives used around the appliance.
Film on the glass
This is a normal result of the curing process of the paint and logs. Glass should be cleaned
within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing
process. A non-abrasive cleaner such as gas fireplace glass cleaner may be necessary. See
your dealer.
Metallic noise
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the appliance.
Is it normal to see the pilot flame burn
continually?
In a standing pilot system the pilot will always stay on.
12
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
3
Maintenance and Service
Any safety screen or guard removed for servicing must be
replaced prior to operating the fireplace.
Doors, Surrounds, Fronts
Frequency: Annually
When properly maintained, your fireplace will give you
many years of trouble-free service. We recommend annual service by a qualified service technician.
By: Homeowner
A. Maintenance Tasks-Homeowner
• Inspect for scratches, dents or other damage and repair
as necessary.
Installation and repair should be done by a qualified service
technician only. The fireplace should be inspected before
use and at least annually by a professional service person.
Tools needed: Protective gloves, stable work surface
• Assess condition of screen and replace as necessary.
• Check that louvers are not blocked.
• Vacuum and dust surfaces.
The following tasks may be performed annually by the
homeowner. If you are uncomfortable performing any of
the listed tasks, please call your dealer for a service appointment.
Remote Control
More frequent cleaning may be required due to lint from
carpeting or other factors. Control compartment, burner
and circulating air passageway of the fireplace must be
kept clean.
Tools needed: Replacement batteries and remote control instructions.
CAUTION! Risk of Burns! The fireplace should be turned
off and cooled before servicing.
Glass Cleaning
Frequency: Seasonally
By: Homeowner
• Locate remote control transmitter and receiver.
• Verify operation of remote. Refer to remote control
operation instructions for proper calibration and setup
procedure.
Frequency: Seasonally
• Place batteries as needed in remote transmitters and
battery-powered receivers.
By: Homeowner
• Place remote control out of reach of children.
Tools Needed: Protective gloves, glass cleaner, drop
cloth and a stable work surface.
If not using your fireplace for an extended period of time
(summer months, vacations/trips, etc), to prevent unintended operation:
CAUTION! Handle fixed glass assembly with care.
Glass is breakable.
• Avoid striking, scratching or slamming glass
• Avoid abrasive cleaners
• DO NOT clean glass while it is hot
• Prepare a work area large enough to accommodate fixed
glass assembly and door frame by placing a drop cloth
on a flat, stable surface.
Note: Fixed glass assembly and gasketing may have residue that can stain carpeting or floor surfaces.
• Remove door or decorative front from fireplace and set
aside on work surface.
• See Section 14.G for instructions to remove fixed glass
assembly.
• Clean glass with a non-abrasive commercially available
cleaner.
- Light deposits: Use a soft cloth with soap and water
- Heavy deposits: Use commercial fireplace glass
cleaner (consult with your dealer)
• Remove batteries from remote controls.
Venting
Frequency: Seasonally
By: Homeowner
Tools needed: Protective gloves and safety glasses.
• Inspect venting and termination cap for blockage or
obstruction such plants, bird nests, leaves, snow, debris,
etc.
• Verify termination cap clearance to subsequent construction (building additions, decks, fences, or sheds). See
Section 6.
• Inspect for corrosion or separation.
• Verify weather stripping, sealing and flashing remains
intact.
• Inspect draft shield to verify it is not damaged or missing.
• Carefully set fixed glass assembly in place on fireplace.
Hold glass in place with one hand and secure glass
latches with the other hand.
• Reinstall door or decorative front.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
13
B. Maintenance Tasks-Qualified Service
Technician
Burner Ignition and Operation
The following tasks must be performed by a qualified service technician.
By: Qualified Service Technician
Gasket Seal and Glass Assembly Inspection
Frequency: Annually
Frequency: Annually
Tools needed: Protective gloves, vacuum cleaner, whisk
broom, flashlight, voltmeter, indexed drill bit set, and a
manometer.
• Verify burner is properly secured and aligned with pilot
or igniter.
By: Qualified Service Technician
Tools needed: Protective gloves, drop cloth and a stable
work surface.
• Inspect gasket seal and its condition.
• Clean off burner top, inspect for plugged ports, corrosion
or deterioration. Replace burner if necessary.
• Inspect fixed glass assembly for scratches and nicks that
can lead to breakage when exposed to heat.
• Replace Glowing embers with new dime-size pieces.
DO NOT block ports or obstruct lighting paths. Refer to
Section 14 for proper ember placement.
• Confirm there is no damage to glass or glass frame.
Replace as necessary.
• Check for smooth lighting and ignition carryover to all
ports. Verify that there is no ignition delay.
• Verify that fixed glass assembly is properly retained and
attachment components are intact and not damaged.
Replace as necessary.
• Inspect for lifting or other flame problems.
Logs
• Verify air shutter setting is correct. See Section 14 for
required air shutter setting. Verify air shutter is clear of
dust and debris.
• Inspect orifice for soot, dirt and corrosion. Verify orifice
size is correct. See Service Parts List for proper orifice
sizing.
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves.
• Inspect for damaged or missing logs. Replace as necessary. Refer to Section 14 for log placement instructions.
• Verify correct log placement and no flame impingement
causing sooting. Correct as necessary.
• Verify manifold and inlet pressures. Adjust regulator as
required.
• Inspect pilot flame pattern and strength. See Figure 3.1
for proper pilot flame pattern. Clean or replace orifice
spud as necessary.
• Verify thermocouple/thermopile millivolt output. Replace
pilot as necessary.
Firebox
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, sandpaper, steel wool,
cloths, mineral spirits, primer and touch-up paint.
• Inspect for paint condition, warped surfaces, corrosion
or perforation. Sand and repaint as necessary.
• Replace fireplace if firebox has been perforated.
Control Compartment and Firebox Top
Frequency: Annually
By: Qualified Service Technician
Tools needed: Protective gloves, vacuum cleaner, dust
cloths
• Vacuum and wipe out dust, cobwebs, debris or pet hair.
Use caution when cleaning these areas. Screw tips that
have penetrated the sheet metal are sharp and should
be avoided.
• Remove all foreign objects.
• Verify unobstructed air circulation.
14
Figure 3.1 Standing Pilot Flame Patterns
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
4
Installer Guide
Getting Started
A. Typical Appliance System
NOTICE: Illustrations and photos reflect typical installations and are for design purposes only. Illustrations/diagrams are not
drawn to scale. Actual product may vary from pictures in manual
HORIZONTAL
TERMINATION CAP
(SECTION 10.L)
Note: Dual venting configurations
ARE NOT allowed. Appliance MUST
be vented EITHER ver tically OR
horizontally.
VERTICAL TERMINATION CAP
(SECTION 10.I)
NON-COMBUSTIBLE ROOF FLASHING
MAINTAINS MINIMUM CLEARANCE
AROUND PIPE (SECTION 10.G)
STORM COLLAR
(SECTION 10.H)
VENT PIPE PENETRATES ROOF
PREFERABLY WITHOUT AFFECTING
ROOF RAFTERS (SECTION 8.C)
VENT PIPE (SECTIONS 7 and 8)
ATTIC INSULATION SHIELD (NOT
SHOWN) MUST BE USED HERE
TO KEEP INSULATION AWAY
FROM VENT PIPE IF ATTIC IS
INSULATED (SECTION 8.D)
CEILING FIRESTOP
ON FLOOR OF ATTIC
(SECTION 8.C)
FRAMING/HEADER
(SECTION 5.B)
FRAMING HEADED OFF
IN CEILING JOISTS
(SECTION 8.C)
OPTIONAL
WALL SWITCH
MANTEL AND
MANTEL LEG
(SECTION 5.D)
SURROUND
HEARTH EXTENSION
GAS LINE
(SECTION 11)
Figure 4.1 Typical System
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
15
B. Design and Installation Considerations
D. Inspect Appliance and Components
Quadra-Fire direct vent gas appliances are designed to
operate with all combustion air siphoned from outside of
the building and all exhaust gases expelled to the outside.
No additional outside air source is required.
• Carefully remove the appliance and components from
the packaging.
Installation MUST comply with local, regional, state and
national codes and regulations. Consult insurance carrier,
local building inspector, fire officials or authorities having
jurisdiction over restrictions, installation inspection and
permits.
• If packaged separately, the log set and appliance grate
must be installed.
Before installing, determine the following:
• Read all of the instructions before starting the installation. Follow these instructions carefully during the
installation to ensure maximum safety and benefit.
• Where the appliance is to be installed.
• The vent system configuration to be used.
• Gas supply piping requirements.
• Electrical wiring requirements.
• The vent system components and decorative doors and
fronts may be shipped in separate packages.
• Report to your dealer any parts damaged in shipment,
particularly the condition of the glass.
WARNING! Risk of Fire or Explosion! Damaged parts
could impair safe operation. DO NOT install damaged, incomplete or substitute components. Keep appliance dry.
• Framing and finishing details.
• Whether optional accessories—devices such as a fan,
wall switch, or remote control—are desired.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. For
assistance or additional information, consult a qualified
service technician, service agency or your dealer.
Hearth & Home Technologies disclaims any responsibility for,
and the warranty will be voided by, the following actions:
• Installation and use of any damaged appliance or vent
system component.
• Modification of the appliance or vent system.
• Installation other than as instructed by Hearth & Home
Technologies.
• Improper positioning of the gas logs or the glass door.
C. Tools and Supplies Needed
Before beginning the installation be sure that the following
tools and building supplies are available.
Tape measure
Framing material
Pliers
Non-corrosive leak check solution
Hammer
Phillips screwdriver
Gloves
Framing square
Voltmeter
Electric drill and bits (1/4 in.)
Plumb line
Safety glasses
Level
Reciprocating saw
Manometer
Flat blade screwdriver
1/2 - 3/4 in. length, #6 or #8 Self-drilling screws
Caulking material (300ºF minimum continuous exposure
rating)
One 1/4 in. female connection (for optional fan).
16
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
Any such action may cause a fire hazard.
WARNING! Risk of Fire, Explosion or Electric Shock!
DO NOT use this appliance if any part has been under
water. Call a qualified service technician to inspect the
appliance and to replace any part of the control system
and/or gas control which has been under water.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
5
Framing and Clearances
NOTICE: Illustrations reflect typical installations and are
FOR DESIGN PURPOSES ONLY. Illustrations/diagrams
are not drawn to scale. Actual installation may vary due to
individual design preference.
A. Selecting Appliance Location
When selecting a location for the appliance it is important to
consider the required clearances to walls (see Figure 5.1).
WARNING! Risk of Fire or Burns! Provide adequate
clearance around air openings and for service access.
Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.
A
N
E
L
F
D
F
A
A
C
C
K
H
B
J
G
I
G
J
M
E
F
G
Min. Min.
in.
42
37 59-1/2
1 1/2 Min. 44
QV32B-A
mm 1066 940 1511 See Section 25
13
1117
D for Alcove
in. 45-1/2 42 64-3/8 Installation
1
1/2 45-1/2
QV36B-A
mm 1155 1067 1635
25
13
1321
Models
A
B
C
D
H
I
J
K
L
M
N
62-1/4 16-1/4 48-1/2 68-3/4 15-1/16 7-1/2 7-1/8
1734
413
1231 1746
383
191 181
64-3/8 16-1/4 48-1/2 68-3/4 16-5/8 7-1/2 9
1861
413
1231 1746
422
191 229
Figure 5.1 Appliance Locations
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
17
firestops should be caulked with caulk with a minimum of
300ºF continuous exposure rating to seal gaps. Gas line
holes and other openings should be caulked with caulk
with a minimum of 300ºF continuous exposure rating or
stuffed with unfaced insulation. If the appliance is being installed on a cement slab, a layer of plywood may be placed
underneath to prevent conducting cold up into the room.
B. Constructing the Appliance Chase
A chase is a vertical box-like structure built to enclose the
gas appliance and/or its vent system. In cooler climates
the vent should be enclosed inside the chase.
NOTICE: Treatment of ceiling firestops and wall shield
firestops and construction of the chase may vary with the
type of building. These instructions are not substitutes
for the requirements of local building codes. Therefore,
you MUST check local building codes to determine the
requirements to these steps.
C. Clearances
NOTICE: Install appliance on hard metal or wood surfaces
extending full width and depth. DO NOT install directly
on carpeting, vinyl, tile or any combustible material other
than wood.
Chases should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building
envelope in any manner.
WARNING! Risk of Fire! Maintain specified air space
clearances to appliance and vent pipe:
Walls, ceiling, base plate and cantilever floor of the chase
should be insulated. Vapor and air infiltration barriers
should be installed in the chase as per regional codes for
the rest of the home. Additionally, in regions where cold
air infiltration may be an issue, the inside surfaces may be
sheetrocked and taped for maximum air tightness.
• Insulation and other materials must be secured to prevent
accidental contact.
• The chase must be properly blocked to prevent blown
insulation or other combustibles from entering and
making contact with fireplace or chimney.
• Failure to maintain airspace may cause overheating and
a fire.
To further prevent drafts, the wall shield and ceiling
A
MEASURE FROM TOP OF UNIT
OPENING OR FROM TOP OF HOOD
E
F
H
B
G
J
C
I
D
* MINIMUM FRAMING DIMENSIONS
A
Models
B
DVP PIPE
SLP PIPE
Rough
Opening
(Width)
Rough
Opening
(Width)
8-5/8
Rough
Opening
(Height)
D
E
Rough
Opening
(Width)
Clearance
to Ceiling
16-1/4
42
32
0
0
SLP PIPE
Rough
Opening
(Depth)
Rough
Opening
(Depth)
16-1/4
F
Combustible Combustible
Floor
Flooring
H
10
254
219
971
699
413
1067
813
0
0
Inches
10
8-5/8
34-3/4
16-1/4
16-1/4
37
32
0
0
Millimeters
254
219
882
699
413
940
813
0
0
13
* Adjust framing dimensions for interior sheathing (such as sheetrock)
C** Add 12 inches for rear venting with one 90º elbow.
Figure 5.2 Clearances to Combustibles
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
I
J
Behind
Sides of
Front of
Appliance Appliance Appliance
Inches
QV32B-A
18
G
Millimeters
QV36B-A
38-1/4
C
**DVP PIPE
1/2
1/2
36
13
13
915
1/2
1/2
36
13
915
D. Mantel and Wall Projections
WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing or finishing material closer than
the minimums listed must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc).
3 IN.
MINIMUM
TOP VIEW
Combustible Mantels
All measurements are in inches.
5-3/8 IN.
MINIMUM
CEILING
UNLIMITED
Note: Clearance from opening
to perpendicular wall.
12
11
10
9
Figure 5.5 Wall Projection (Acceptable on one side of opening.)
8
32
7
6
5
4
3
4
5
6
7
8
9
10
11
12
13
3-1/2 in.
1/2 in.
SHEETROCK
NON-COMBUSTIBLE
BOARD SHIPPED
WITH APPLIANCE
TOP OF HOOD OR FIREPLACE OPENING
Figure 5.3 Minimum Vertical and Maximum Horizontal
Dimensions of Combustibles
1/2 in.
Combustible Mantel Legs or Wall Projections
3 IN.
MINIMUM
TOP VIEW
5-3/8 IN.
MINIMUM
3 FT. MAXIMUM
Note: Clearance from opening
to perpendicular wall.
AIR SPACE
Figure 5.6 Non-Combustible Zone
Figure 5.4 Clearances to Mantel Legs or Wall Projections
(Acceptable on both sides of opening.)
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
19
6
Termination Locations
A. Vent Termination Minimum Clearances
WARNING
A
B
6 in. (minimum) up to 20 in.
152 mm/508 mm
18 in. minimum
457 mm
20 in. and over
0 in. minimum
Fire Risk.
Maintain vent clearance to combustibles as
specified.
• DO NOT pack air space with insulation or other
materials.
Failure to keep insulation or other materials away
from vent pipe may cause overheating and fire.
Gas, Wood or Fuel Oil
Termination Cap
B
A*
HORIZONTAL
OVERHANG
2 FT.
MIN.
20 INCHES MIN.
Gas
Termination
Cap **
VERTICAL
WALL
LOWEST
DISCHARGE
OPENING
GAS DIRECT VENT
TERMINATION CAP
X
12
*
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
**
If using decorative cap cover(s), this distance may need to be
increased. Refer to the installation instructions supplied with the
decorative cap cover.
In a staggered installation with both gas and wood or fuel oil
terminations, the wood or fuel oil termination cap must be
higher than the gas termination cap.
Figure 6.2 Staggered Termination Caps
Roof Pitch
H (Min.) Ft.
Flat to 6/12...........................................................1.0*
Over 6/12 to 7/12 .................................................1.25*
Over 7/12 to 8/12 .................................................1.5*
Over 8/12 to 9/12 .................................................2.0*
Over 9/12 to 10/12 ...............................................2.5
Over 10/12 to 11/12 .............................................3.25
Over 11/12 to 12/12 .............................................4.0
Over 12/12 to 14/12 .............................................5.0
Over 14/12 to 16/12 .............................................6.0
Over 16/12 to 18/12 .............................................7.0
Over 18/12 to 20/12 .............................................7.5
Over 20/12 to 21/12 .............................................8.0
* 3 foot minimum in snow regions
Figure 6.1 Minimum Height From Roof To Lowest Discharge
Opening
20
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
O
N
P
R
F
C
V
Q
B
J
H or i
B
V
D
B
V
V
V
H
V
X
G
M
V
A
V
E
H
V
V
V
L
A
V
V = VENT TERMINAL
X = AIR SUPPLY INLET
K
C
Covered Alcove Applications
(Spaces open only on one side and with an overhang)
= 9 inches...................clearance to outside corner
E
= 6 inches...................clearance to inside corner
= 3 ft. (Canada) ..........not to be installed above a gas meter/regulator assembly within 3 feet
horizontally from the center-line of the
regulator
G = 3 ft ...........................clearance to gas service regulator
vent outlet
H
= 12 inches.................clearance to non-mechanical (unpowered) air supply inlet, combustion air
inlet or direct-vent termination
i
= 3 ft. (U.S.A.)
6 ft. (Canada) ...........clearance to a mechanical (powered)
air supply inlet
All mechanical air intakes within 10 feet of a termination cap
must be a minimum of 3 feet below termination.
J
= 7 ft. ......................... On public property: clearance above
paved sidewalk or a paved driveway.
A vent shall not terminate directly above a sidewalk or paved
driveway which is located between two single family dwellings
and serves both dwellings.
K
= 6 inches.................clearance from sides of electrical
service
L
= 12 inches................clearance above electrical service
Location of the vent termination must not interfere with access to the
electrical service.
M
= 18 inches ....................clearance under veranda, porch, deck,
balcony or overhang
42 inches ................vinyl or composite overhang
Permitted when veranda, porch, deck or balcony is fully open
on a minimum of 2 sides beneath the floor.
Figure 6.3 Minimum Clearances for Termination
= 6 inches ........... non-vinyl sidewalls
O
= 18 inches ......... non-vinyl soffit and overhang
P
= 8 ft.
42 inches ......... vinyl soffit and overhang
= 18 inches.................clearance below unventilated soffit
18 inches.................clearance below ventilated soffit
30 inches .................clearance below vinyl soffits and
electrical service
D
N
12 inches ......... vinyl sidewalls
F

V
V
= 12 inches.................clearances above grade, veranda,
porch, deck or balcony
= 12 inches.................clearance to window or door that may
be opened, or to permanently closed
window
B
K
C
= AREA WHERE TERMINAL IS NOT PERMITTED
A
Electrical
Service
QMIN
RMAX
1 cap
3 feet
2 x Q ACTUAL
2 caps
6 feet
1 x Q ACTUAL
3 caps
9 feet
2/3 x Q ACTUAL
4 caps
12 feet
1/2 x Q ACTUAL
QMIN = # termination caps x 3
RMAX = (2 / # termination caps) x QACTUAL
Measure vertical clearances from this surface.
Measure horizontal clearances from this surface.
CAUTION! Risk of Burns! Termination caps are HOT,
consider proximity to doors, traffic areas or where people
may pass or gather (sidewalk, deck, patio, etc.). Listed cap
shields available. Contact your dealer.
•
Local codes or regulations may require different
clearances.
•
Vent system termination is NOT permitted in screened
porches.
•
Vent system termination is permitted in porch areas with
two or more sides open.
•
Hearth & Home Technologies assumes no responsibility
for the improper performance of the appliance when the
venting system does not meet these requirements.
Vinyl protection kits are suggested for use with vinyl siding.
•
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
21
7
Vent Information and Diagrams
A. Approved Pipe
DO NOT mix pipe, fittings or joining methods from different manufacturers.
Vertical
12
in
.
The pipe is tested to be run inside an enclosed wall.
There is no requirement for inspection openings at each
joint within the wall.
8-1/2 in.
WARNING! Risk of Fire or Asphyxiation. This appliance requires a separate vent. DO NOT vent to a pipe
serving a separate solid fuel burning appliance.
B. Vent Table Key
Horizontal
The abbreviations listed in this vent table key are used in
the vent diagrams.
Symbol
Figure 7.1
Description
V1
First section (closest to appliance) of vertical length
V2
Second section of vertical length
H1
First section (closest to appliance) of horizontal length
H2
Subsequent sections of horizontal length
C. Use of Elbows
Diagonal runs have both vertical and horizontal vent aspects when calculating the effects. Use the rise for the
vertical aspect and the run for the horizontal aspect (see
Figure 7.1).
D. Measuring Standards
Vertical and horizontal measurements listed in the vent
diagrams were made using the following standards.
• Pipe measurements are shown using the effective length
of pipe (see Figure 7.2).
• Horizontal terminations are measured to the outside
mounting surface (flange of termination cap) (see Figure
6.4).
• Vertical terminations are measured to bottom of
termination cap.
• Horizontal pipe installed level with no rise.
Two 45º elbows may be used in place of one 90º elbow.
On 45º runs, one foot of diagonal is equal to 8-1/2 in. (216
mm) horizontal run and 8-1/2 in. (216 mm) vertical run. A
length of straight pipe is allowed between two 45º elbows
(see Figure 7.1).
Pipe
DVP4
Effective
Height/Length
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
Effective Length
Inches
Millimeters
4
102
DVP6
6
152
DVP12
12
305
DVP24
24
610
DVP36
36
914
DVP48
48
1219
DVP6A
3 to 6
76 to 152
DVP12A
3 to 12
76 to 305
DVP12MI 3 to 12
76 to 305
DVP24MI 3 to 24
76 to 610
Figure 7.2 DVP Pipe Effective Length
22
8-1/2 in.
This appliance is approved for use with Hearth & Home
Technologies DVP or SLP venting systems. Refer to Section 16B for vent component information.
E. Use of Flex Vent
The flex vent must be supported with
the spacing between support intervals
not exceeding 4 feet, with no more
than 1/2 inch sag between supports.
3 in.
CLEARANCE
A support is required at each change
in venting direction, and in any location
where it is necessary to maintain the
necessary clearance to combustibles.
A simple “up and out” installation (Figure 7.3) requires only enough support
to maintain the necessary clearance
to combustibles. However, the vent attachment point and the firestop location are considered to be supports.
TERMINATION CAP
FLEX VENT
1 in.
CLEARANCE
Figure 7.3
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
23
F. Vent Diagrams
Top Vent - Horizontal Termination
Venting with 1 elbow (NG)
V1 Minimum
90 Elbow
Top Vent - Horizontal Termination
Venting with 1 elbow (Propane)
H1 Maximum
V1 Minimum
H1 Maximum
1 ft.
305 mm
1/2 ft.
152 mm
2 ft.
610 mm
1/2 ft.
152 mm
1 ft.
305 mm
1-1/2 ft.
457 mm
3 ft.
914 mm
1-1/2 ft.
457 mm
3 ft.
914 mm
2-1/2 ft.
762 mm
5 ft.
1.5 m
2-1/2 ft.
762 mm
5 ft.
1.5 m
3-1/2 ft.
1.1 m
7 ft.
2.1 m
3-1/2 ft.
1.1 m
7 ft.
2.1 m
4-1/2 ft.
1.4 m
15 ft.
4.6 m
4-1/2 ft.
1.4 m
15 ft.
4.6 m
90 Elbow
H1 MAX. =15 ft. (4.6 m)
V1 + H1 MAX. = 40 ft. (12.2 m)
Not allowed
H1 MAX. =15 ft. (4.6 m)
V1 + H1 MAX. = 40 ft. (12.2 m)
Note: Use SLP Series
components only.
Note: There MUST be a 25%
reduction in total H when
using flex vent except when
using the simple up and out
installation (see Figure 5.3).
V1
H1
Figure 7.4
24
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
Top Vent - Horizontal Termination
Venting with 2 elbows (Propane)
Top Vent - Horizontal Termination
Venting with 2 elbows (NG)
V1 Minimum
H1 + H2 Maximum
90 Elbow
V1 Minimum
90 Elbow
H1 + H2 Maximum
0 ft.
0 mm
1/2 ft.
152 mm
1 ft.
305 mm
1/2 ft.
152 mm
0 ft.
0 mm
1-1/2 ft.
457 mm
2 ft.
610 mm
1-1/2 ft.
457 mm
2 ft.
610 mm
2-1/2 ft.
762 mm
4 ft.
1.2 m
2-1/2 ft.
762 mm
4 ft.
1.2 m
3-1/2 ft.
1.1 m
6 ft.
1.8 m
3-1/2 ft.
1.1 m
6 ft.
1.8 m
4-1/2 ft.
1.4 m
14 ft.
4.3 m
4-1/2 ft.
1.4 m
14 ft.
4.3 m
H1 + H2 MAX. =14 ft. (4.3 m)
V + H1 + H2 MAX. = 40 ft. (12.2 m)
Not Allowed
H1 + H2 MAX. =14 ft. (4.3 m)
V + H1 + H2 MAX. = 40 ft. (12.2 m)
Note: Use SLP Series
components only.
Note: There MUST be a 25%
reduction in total H when
using flex vent except when
using the simple up and out
installation (see Figure 5.3).
V1
H2
H1
INSTALLED
HORIZONTALLY
Figure 7.5
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
25
Top Vent - Horizontal Termination
Venting with 3 elbows (NG)
V1 Minimum
90 Elbow
Top Vent - Horizontal Termination
Venting with 3 elbows (Propane)
H1 + H2 Maximum
0 ft.
0 mm
V1 Minimum
H1 + H2 Maximum
90 Elbow
Not Allowed
1/2 ft.
152 mm
1 ft.
305 mm
1/2 ft.
152 mm
0 ft.
0 mm
1-1/2 ft.
457 mm
2 ft.
610 mm
1-1/2 ft.
457 mm
2 ft.
610 mm
2-1/2 ft.
762 mm
4 ft.
1.2 m
2-1/2 ft.
762 mm
4 ft.
1.2 m
3-1/2 ft.
1.1 m
6 ft.
1.8 m
3-1/2 ft.
1.1 m
6 ft.
1.8 m
H1 + H2 MAX. =14 ft. (4.3 m)
V1+ V2 + H1 + H2 MAX. = 40 ft. (12.2 m)
H1 + H2 MAX. =14 ft. (4.3 m)
V1+ V2 + H1 + H2 MAX. = 40 ft. (12.2 m)
Note: There MUST be a 25%
reduction in total H when
using flex vent except when
using the simple up and out
installation (see Figure 5.3).
Note: Use SLP Series
components only.
H2
V2
H1
Figure 7.6
26
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
V1
Top Vent - Vertical Termination
Exhaust restrictor Instructions
1. Install the exhaust restrictor over the center of the exhaust outlet in the firebox (see Figure 7.8).
No Elbow
2. Center the exhaust restrictor in the open end of the
exhaust outlet and secure through the slots on the exhaust restrictor with the 2-1/4 in. self tapping screws
provided in the appliance manual bag.
Note: Use SLP Series
components only.
Note: If installing a vertical vent/termination off the top of
the appliance, the optional vertical termination baffle may be
needed.
V1 = 60 ft. Max. (18.3 m)
INNER HEAT SHIELD
To access the
exhaust openings,
remove the inner
heat shield. To
remove inner heat
shield, remove the
two screws.
Top Vent Application
Exhaust restrictor
V1
Rear Vent Application
Exhaust restrictor
Note: Be sure to reinstall the inner heat
shield after exhaust
restrictor installation.
Figure 7.7
Exhaust restrictors are recommended for these vertically terminated products which have excessive draft.
Exhaust restrictors will compensate for high draft, and
restore visual flame height. If the vent configuration has
a total vertical of 15-60 feet, an exhaust restrictor may
be needed. The exhaust restrictor can be located in the
appliance manual bag.
Figure 7.8
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
27
Top Vent - Vertical Termination
Venting with 2 elbows (NG)
V1 Minimum
H1 Maximum
90 Elbow
1 ft.
305 mm
V2
V1 + V2 Minimum
*
*
1/2 ft.
152 mm
2 ft.
610 mm
*
*
1-1/2 ft.
457 mm
3 ft.
914 mm
*
*
2-1/2 ft.
762 mm
5 ft.
1.5 m
*
*
3-1/2 ft.
1.1 m
7 ft.
2.1 m
*
*
4-1/2 ft.
1.4 m
15 ft.
4.6 m
*
*
H1 MAX. =15 ft. (4.6 m)
V1+ V2 + H1 MAX. = 40 ft. (12.2 m)
* No specific restrictions on this value EXCEPT V1 + V2 + H1 cannot exceed 40 ft. (12.2 m)
Top Vent - Vertical Termination
Venting with 2 elbows (Propane)
V1 Minimum
H1 Maximum
V2
V1 + V2 Minimum
90 Elbow
Not Allowed
*
*
1/2 ft.
152 mm
1 ft.
305 mm
*
*
1-1/2 ft.
457 mm
3 ft.
914 mm
*
*
2-1/2 ft.
762 mm
5 ft.
1.5 m
*
*
3-1/2 ft.
1.1 m
7 ft.
2.1 m
*
*
4-1/2 ft.
1.4 m
15 ft.
4.6 m
*
*
H1 MAX. =15 ft. (4.6 m)
V1+ V2 + H1 MAX. = 40 ft. (12.2 m)
* No specific restrictions on this value EXCEPT V1 + V2 + H1 cannot exceed 40 ft. (12.2 m)
Note: There MUST be a 25%
reduction in total H when
using flex vent except when
using the simple up and out
installation (see Figure 5.3).
Note: Use SLP Series
components only.
V2
H1
V1
Figure 7.9
28
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
Top Vent - Vertical Termination
Venting with 3 elbows (NG)
V1 Minimum
H1 Maximum
90 Elbow
0 ft.
305 mm
V2
V1 + V2 Minimum
*
*
1/2 ft.
152 mm
2 ft.
610 mm
*
*
1-1/2 ft.
457 mm
3 ft.
914 mm
*
*
2-1/2 ft.
762 mm
5 ft.
1.5 m
*
*
3-1/2 ft.
1.1 m
7 ft.
2.1 m
*
*
4-1/2 ft.
1.4 m
15 ft.
4.6 m
*
*
H MAX. =15 ft. (4.6 m)
V1+ V2 + H1 MAX. = 40 ft. (12.2 m)
* No specific restrictions on this value EXCEPT V1 + V2 + H1 + H2 cannot exceed 40 ft. (12.2 m)
Top Vent - Vertical Termination
Venting with 3 elbows (Propane)
V1 Minimum
90 Elbow
H1 Maximum
V2
V1 + V2 Minimum
Not Allowed
*
*
1/2 ft.
152 mm
1 ft.
305 mm
*
*
1-1/2 ft.
457 mm
3 ft.
914 mm
*
*
2-1/2 ft.
762 mm
5 ft.
1.5 m
*
*
3-1/2 ft.
1.1 m
7 ft.
2.1 m
*
*
4-1/2 ft.
1.4 m
15 ft.
4.6 m
*
*
H MAX. =15 ft. (4.6 m)
V1+ V2 + H1 MAX. = 40 ft. (12.2 m)
* No specific restrictions on this value EXCEPT V1 + V2 + H1 + H2 cannot exceed 40 ft. (12.2 m)
Note: Use SLP Series
components only.
Note: There MUST be a 25%
reduction in total H when
using flex vent except when
using the simple up and out
installation (see Figure 5.3).
V2
H1
H2
V1
INSTALLED
HORIZONTALLY
Figure 7.10
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
29
Top Vent - Vertical Termination - (continued)
V1 Min.
Four 90º Elbows
1-1/2 ft.
H1 Max.
457 mm
4 ft.
1.2 m
V2 Min.
4 ft.
1.2 m
H2 Max.
4 ft.
1.2 m
V1 + V2 + V3 + H1 + H2 Maximum= 40 ft. (12.2 m)
V3
V2
H2
Note: Use SLP Series
components only.
H1
Note: There MUST be a 25%
reduction in total H when using
flex vent except when using the
simple up and out installation
(see Figure 5.3).
V1
Figure 7.11
30
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
V3 Min.
3-1/2 ft.
1.0 m
Rear Vent - Horizontal Termination
No Elbows
H1 = 24 in. (711 mm) Maximum
Note: Use DVP Series
components only.
H1
Figure 7.12
Rear Vent - Horizontal Termination
Venting with 2 elbows
Note: Use DVP Series
components only.
H1 MAX.
V1 MIN.
1-1/2 ft. 457 mm
Back to back elbows
H2 MAX.
H1 + H2 MAX.
1 ft.
305 mm 2-1/2 ft. 762 mm
3 ft.
914 mm
1 ft.
305 mm
3 ft.
914 mm
6 ft.
1.8 m
5 ft.
1.5 m
3 ft.
914 mm
5 ft.
1.5 m
10 ft.
3.0 m
7 ft.
2.1 m
5 ft.
1.5 m
7 ft.
2.1 m
14 ft.
4.3 m
H1 MAX. = 7 ft. (2.1 m)
H1 + H2 MAX. = 14 ft. (4.3 m)
V1 + H1 + H2 MAX. = 40 ft. (12.2 m)
H2
V1
H1
Figure 7.13
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
31
Rear Vent - Horizontal Termination
Venting with 3 elbows
Note: Use DVP Series
components only.
INSTALLED
HORIZONTALLY
H1 MAX.
V1 MIN.
H1 + H2 MAX.
1-1/2 ft. 457 mm
Back to back elbows
H1 + H2+ H3 MAX.
1 ft.
305 mm
2-1/2 ft.
762 mm
5-1/2 ft.
1.7 m
3-1/2 ft.
1.1 m
1 ft.
305 mm
2 ft.
610 mm
5-1/2 ft.
1.7 m
2 ft.
610 mm
4 ft.
1.2 m
9-1/2 ft.
2.9 m
7-1/2 ft.
2.3 m
3 ft.
914 mm
6 ft.
1.8 m
13-1/2 ft.
4.1 m
H1 MAX. = 7-1/2 ft. (2.3 m)
H1 + H2+ H3 MAX. = 13-1/2 ft. (4.1 m)
V1 + H1 + H2+ H3 MAX. = 40 ft. (12.2 m)
H3
H2
V1
Figure 7.14
H1
Rear Vent - Vertical Termination
Venting with 1 elbow
Note: Use DVP Series
components only.
V1 MIN.
H1 MAX.
1 ft.
305 mm
3-1/2 ft.
1.1 m
2 ft.
610 mm
5-1/2 ft.
1.7 m
3 ft.
914 mm
7-1/2 ft.
2.3 m
H1 MAX. = 7-1/2 ft. (2.3 m)
V1 + H1 MAX. = 40 ft. (12.2 m)
V1
H1
Figure 7.15
32
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
Rear Vent - Vertical Termination
Venting with 2 elbows
Note: Use DVP Series
components only.
H1 + H2 MAX
V1 MIN.
Back to back elbows
1/2 ft.
152 mm
2-1/2 ft.
762 mm
1 ft.
305 mm
4-1/2 ft.
1.4 m
2 ft.
610 mm
6-1/2 ft.
2.0 m
3 ft.
914 mm
H MAX. = 6-1/2 ft. (2 m)
V + H+ H1 MAX. = 40 ft. (12.2 m)
V2
INSTALLED
HORIZONTALLY
H1
H2
Figure 7.16
Rear Vent - Vertical Termination
Venting with 3 elbows
V1 MIN.
V2
Back to back elbows
H1 MAX.
H2 MAX.
H1 + H2 MAX.
1-1/2 ft.
457 mm
1 ft.
305 mm
2-1/2 ft.
762 mm
1 ft.
305 mm
3-1/2 ft.
1.1 m
3 ft.
914 mm
6-1/2 ft.
2.0 m
2 ft.
610 mm
5-1/2 ft.
1.7 m
5 ft.
1524 mm
10-1/2 ft.
3.2 m
3 ft.
914 mm
7-1/2 ft.
2.3 m
7 ft.
2.1 m
14-1/2 ft.
4.4 m
H1 MAX. = 7-1/2 ft. (2.3 m)
H1 + H2 MAX. = 14-1/2 ft. (4.4 m)
V1 + V2 + H1 + H2 MAX. = 40 ft. (12.2 m)
H2
Note: Use DVP Series
components only.
V1
Figure 7.17
H1
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
33
Coaxial to Colinear Venting
The coaxial to colinear adapter (DV-46DVA-GCL) is approved for installations into solid fuel masonry or factory
built fireplaces that have been installed in accordance
with the National, Provincial, State and local building
codes. The DV-46DVA-GCL must be recessed into existing masonry fireplace. See Table 1 and Figure 7.20.
OUTSIDE FACE OF
FIREPLACE
EXHAUST VENT PIPE
TOP OF FIREPLACE
OPENING
5 IN. MIN.
INLET AIR VENT PIPE
EXHAUST VENT PIPE
3 IN. MIN.
SHADED AREA DEFINED AS
“INSIDE EXISTING MASONRY FIREPLACE”
Figure 7.19 Coaxial/Colinear Appliance Adapter (DV-46DVA-GCL)
WARNING! Risk of Fire! Coaxial to colinear venting
configuration may only be used in existing non-combustible chimney. Installation in any other venting application
could cause fire.
Figure 7.20 Existing Fireplace DV-46DVA-GCL Clearance
Requirements
Clearances to Combustibles:
Refer to Section 5 for clearances to the appliance, mantel, mantel legs and wall projection.
Refer to Section 8 for pipe clearances to combustibles.
Prior to installing the gas appliance:
• Have the chimney and adjacent structure inspected
and cleaned by qualified professionals. Hearth & Home
Technologies recommends that NFI or CSIA certified professionals, or technicians under the direction of certified
professionals, conduct a minimum of a NFPA 211 Level
2 inspection of the chimney.
• Replace component parts of the chimney and fireplace
as specified by the professionals.
• Ensure all joints are properly engaged and the chimney
is properly secured.
Table 1
CLEARANCE TO COMBUSTIBLES REQUIREMENTS
DV-46DVA-GCL
3 IN.
Exhaust Vent Pipe
5 IN.
Termination Cap
For installation of termination cap see minimum vent
heights for various pitched roofs. See Section 6 of appliance owner’s manual.
Flue Damper
Fully lock the solid fuel fireplace’s flue damper in the open
position, OR completely remove it.
Venting Components
The LINK-DV30B is approved for use with the coaxial/colinear venting application. The LINK-DV30B kit includes:
• Two 30 feet sections of flexible vent pipe (3 inches Ø).
One section is used to draw combustion air and the other
section is used to expel exhaust gases.
• One vertical termination cap.
CAUTION! DO NOT use any flue restrictor when venting with the DV-46DVA-GCL adapter and LINK-DV30B
kit. This may result in poor flame appearance, sooting,
pilot malfunction, or overheating.
34
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
Connecting the DV-46DVA-GCL Adapter to Appliance
Top Vent
• Remove top seal cap and insulation if equipped. See
Section 14, “Appliance Setup.” Attach the DV-46DVAGCL adapter to the appliance starting collar with 3-1/2
in. self-tapping screws. See Figure 7.21.
Rear Vent
• Remove the rear seal cap and insulation if equipped.
Connect the DVP-2SL adapter to the vertically positioned
elbow. Follow installation instructions included with DVP2SL kit. Secure DV-46DVA-GCL adapter to DVP-2SL with
3-1/2 in. self-tapping screws. See Figure 7.21.
Connecting the LINK-DV30B to the DV-46DVA-GCL
adapter
• Insert the two sections of flexible vent pipe down the
existing chimney.
• Attach one section of flexible vent pipe to the exhaust
collar on top of the DV-46DVA-GCL adapter with three
self-tapping screws.
• Attach one section of flexible vent pipe to the inlet collar
on top of the DV-46DVA-GCL adapter with three selftapping screws.
• To minimize cold air drafts, seal around the flex vents
at the damper inside the chimney with non-combustible
unfaced fiberglass or rock wool insulation.
The DV-46DVA-GCL adapter must be recessed into existing
masonry fireplace. This measurement is taken from the top
of the fireplace opening. See Table 1 and Figure 7.20.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Do NOT connect this gas appliance to a chimney flue
serving a separate solid fuel or gas burning appliance.
• May impair safe operation of this appliance or other
appliances connected to the flue.
• Vent this appliance directly outside.
• Use separate vent system for this appliance.
CAUTION! DO NOT use any flue restrictor when venting with the DV-46DVA-GCL
adapter and LINK-DV30B kit. This may result in poor flame appearance, sooting, pilot
malfunction, or overheating.
REAR VENT
TERMINATION CAP
TOP VENT
TERMINATION CAP
NOTICE: To achieve optimum performance of appliance, minimize or
avoid bends in exhaust vent pipe.
V
V
EXISTING CHIMNEY
EXISTING CHIMNEY
EXHAUST AIR
VENT PIPE
INLET AIR
VENT PIPE
EXISTING CHIMNEY
EXHAUST AIR
VENT PIPE
INLET AIR
VENT PIPE
EXISTING CHIMNEY
To minimize cold air
drafts, seal with
non-combustible
insulation.
DIRECT VENT FIREPLACE
To minimize cold air
drafts, seal with
non-combustible
insulation.
DIRECT VENT FIREPLACE
HEARTH
FLOOR
FLOOR
HEARTH
H
V
H
V
Minimum
10 ft.
3.05 m
0 ft.
0 mm
Minimum
10 ft.
3.05 m
Maximum
40 ft.
12.2 m
2 ft.
610 mm
Maximum
40 ft.
12.2 m
Figure 7.21
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
35
8
Vent Clearances and Framing
A. Pipe Clearances to Combustibles
B. Wall Penetration Framing
WARNING! Risk of Fire! Maintain air space clearance to
vent. DO NOT pack insulation or other combustibles:
Combustible Wall Penetration
• Between ceiling firestops
• Between wall shield firestops
• Around vent system
Failure to keep insulation or other material away from
vent pipe may cause over heating and fire.
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).
• DVP heat shield - designed to be used on a wall 4 in. to 7-1/4 in. (102 mm to 184
mm) thick.
• If wall thickness is less than 4 in. the existing heat shields must be field trimmed. If
wall thickness is greater than 7-1/4 in. a DVP-HSM-B will be required.
• SLP heat shield - designed to be used on a wall 4-3/8 in. to 7-5/8 in. (111 mm to
194 mm thick).
• If wall thickness is less than 4-3/8 the existing heat shields must be field trimmed.
If wall thickness is greater than 7-5/8 in. a DVP-HSM-B will be required.
(DVP-SLP Pipe Shown)
3 in. (76 mm)
top clearance
Heat
Shield
3 in. (76 mm)
top clearance *
Heat
Shield
1 in. (25 mm)
clearance around
vertical sections
1 in. (25 mm)
clearance
bottom & sides
Wall
Shield
Firestop
Whenever a combustible wall is penetrated, you must
frame a hole for the wall shield firestop(s). The wall shield
firestop maintains minimum clearances and prevents cold
air infiltration.
• The opening must be framed on all four sides using the
same size framing materials as those used in the wall
construction.
• SLP pipe - A wall shield firestop must be placed on each
side of an interior wall. A minimum 1-1/2 in. (38 mm)
overlap of attached heat shields must be maintained.
• DVP pipe - A wall shield firestop is required on one side
only on interior walls. If your local inspector requires a
wall shield firestop on both sides, then both wall shield
firestops must have a heat shield (refer to Section 16.B.)
attached to them.
• See Section 10.M. for information for regarding the installation of a horizontal termination cap.
Non-Combustible Wall Penetration
If the hole being penetrated is surrounded by noncombustible materials such as concrete, a hole with diameter
one inch greater than the pipe is acceptable.
Whenever a non-combustible wall is penetrated, the wall
shield firestop is only required on one side and no heat
shield is necessary.
WALL
3 in. (76 mm)
top clearance *
Heat
Shield
Heat
Shield
Wall
Shield
Firestop
1 in. (25 mm)
clearance
bottom & sides
10 in.
10 in.
C
D
10 in.
12 in.
WALL
* When using SLP or SL-D pipe, minimum clearances from the vent pipe to combustible materials at inside wall firestops are: Top: 2-1/2 in. (64 mm)
Bottom: 1/2 in. (13 mm)
Sides: 1 in. (25 mm)
A*
B*
Figure 8.1 Horizontal Venting Clearances To Combustible
Materials
QV32B-A
QV36B-A
in.
mm
in.
mm
A*
36-1/2
927
41
1041
B*
24-3/8
619
27-7/8
708
C
35-1/2
902
40
1016
D
23-3/8
594
26-7/8
683
* Shows center of vent framing hole for top or rear venting. The center of the
hole is one (1) in. (25.4 mm) above the center of the horizontal vent pipe.
Figure 8.2 Wall Penetration
36
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
C. Install the Ceiling Firestop
A ceiling firestop MUST be used between
floors and attics.
• DVP pipe only - Frame an opening 10 in.
by 10 in. (254 mm by 254 mm) whenever
the vent penetrates a ceiling/fl oor (see
Figure 8.3).
ATTIC ABOVE
• SLP pipe only - Frame opening 9 in. x 9
in. (229 mm x 229 mm) whenever the vent
penetrates a ceiling/floor (see Figure 8.3).
• Frame the area with the same sized lumber
as used in ceiling/floor joist.
A
• The ceiling firestop may be installed above or
below the ceiling joists when installed with a
attic insulation shield. It must be under joists
between floors that are not insulated. Refer
to Figure 8.4.
• Secure with three fasteners on each side.
A
WARNING! Risk of Fire! DO NOT pack insulation around the vent. Insulation must be kept
back from the pipe to prevent overheating.
PIPE
A
DVP
10 in. (254 mm)
SLP
9 in. (229 mm)
Figure 8.3 Installing Ceiling Firestop
INSTALL ATTIC INSULATION SHIELDS
BEFORE OR AFTER INSTALLATION OF VENT SYSTEM
3 FASTENERS
PER SIDE
CEILING FIRESTOP
INSTALLED BELOW CEILING
CEILING FIRESTOP
INSTALLED ABOVE CEILING
Figure 8.4 Installing the Attic Shield
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
37
D. Install Attic Insulation Shield
WARNING! Fire Risk. DO NOT allow loose materials or
insulation to touch vent. Hearth & Home Technologies
Inc. requires the use of an attic shield.
BEND ALL TABS INWARD 90°
TO MAINTAIN CLEARANCE
AND PREVENT INSULATION
FROM FALLING INSIDE
The National Fuel Gas Code ANSI Z223.1 and NFPA 54
requires an attic shield constructed of 26 gauge minimum
metal that extends at least 2 in. (51 mm) above insulation.
Attic shields must meet specified clearance and be secured in place.
Flat Ceiling Installation
• Remove one shield from box.
NOTICE: Cut previously installed batt insulation to make
room for the attic insulation shield.
INSERT 3
SCREWS
• Wrap shield around pipe if pipe is already installed in
area to be insulated.
• Match the three holes in each side and fasten with three
screws to form a tube.
• Bend three tabs on the bottom of the shield outward to
allow attachment to the ceiling firestop.
Figure 8.5 Attic Insulation Shield
• Bend the remaining bottom tabs inward 90º to maintain
the air space between the pipe and the shield. Set the
shield on the ceiling firestop and attach to the firestop.
• Bend all tabs inward 90º around the top of the shield.
These tabs must be used to prevent blown insulation
from getting between the shield and vent pipe, and to
maintain air space clearance.
Vaulted Ceiling Installation
• Remove one shield from box.
NOTICE: Cut previously installed batt insulation to make
room for the attic insulation shield.
• Cut the attic insulation shield (if application is for vaulted
ceiling) to fit your ceiling pitch. Snip cut edge to recreate
1 in. bend tabs all the way around the bottom.
• Wrap shield around pipe if pipe is already installed in
area to be insulated.
• Match the three holes in each side and fasten with three
screws to form a tube.
• Bend three tabs on the bottom of the shield outward to
allow attachment to the ceiling firestop.
• Bend the remaining bottom tabs inward 90º to maintain
the air space between the pipe and the shield. Set the
shield on the ceiling firestop and attach to the firestop.
• Bend all tabs inward 90º around the top of the shield.
These tabs must be used to prevent blown insulation
from getting between the shield and vent pipe, and to
maintain air space clearance.
38
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
BEND 3 TABS
OUTWARD TO
FASTEN TO CEILING
FIRESTOP-BEND
REMAINING TABS
INWARD 90 DEGREES
TO MAINTAIN
CLEARANCE
9
Appliance Preparation
A. Top Vent
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.
Note: Actual unit may look different than the fireplace shown
in this section.
NOTICE: Once appliance is set up for top or rear venting,
it CANNOT be changed at a later time.
2 SCREWS
Figure 9.4 Remove the seal cap.
Figure 9.1 For top vent, remove the two screws holding the
top heat shield in place. For rear vent, see Section 9.B.
WARNING! Risk of Fire! Do not remove heat shield. Elevated header temperatures may cause a fire.
Figure 9.2 Rotate the top heat shield to the vertical
position as shown above. The heat shield must remain in
the vertical position.
Figure 9.5 Remove the insulation basket and white insulation from the center vent pipe.
2 SCREWS
Figure 9.3 Replace the two screws as shown.
Figure 9.6 Remove the insulation from the outer vent pipe.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
39
NOTICE: Once the seal cap has been removed it CANNOT
be reattached.
2 SCREWS
Figure 9.7 To attach the first section of vent pipe, make
sure to use the fiberglass gasket to seal between the first
vent component and the outer fireplace wrap. Use 2 self
tapping screws to secure the gasket to the outer wrap.
Figure 9.10 Fold the center parts of the retaining band
out and use to remove the seal cap.
Note: Once the vent cap has been removed, it cannot be
reattached.
B. Rear Vent
NOTICE: Once appliance is set up for top or rear venting,
it CANNOT be changed at a later time.
Figure 9.11 Discard the seal cap, remove and discard
the insulation basket. Note: Once the vent cap has been
removed it CANNOT be reattached.
Figure 9.8 Fold the tabs toward the center of the fire plug
(90°) and remove the insulation gasket.
Figure 9.9 Cut the metal retaining band and fold the
sides out.
40
Figure 9.12 Attach the first vent section (it will snap into
place). Slide the insulation gasket onto the vent section,
up against the appliance and over the tabs. Use two selftapping screws to secure gasket to outer wrap.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
C. Securing and Leveling the Appliance
WARNING! Risk of Fire! Prevent contact with:
• Sagging or loose insulation
• Insulation backing or plastic
• Framing and other combustible materials
Block openings into the chase to prevent entry of blownin insulation. Make sure insulation and other materials
are secured.
DO NOT notch the framing around the appliance
standoffs.
Failure to maintain air space clearance may cause
overheating and fire.
The diagram shows how to properly position and secure
the appliance (see Figure 9.11). Nailing tabs are provided
to secure the appliance to the framing members.
NAILING TABS
BOTH SIDES
• Bend out nailing tabs on each side.
• Place the appliance into position.
SCREW HOLES
• Keep nailing tabs flush with the framing.
• Level the appliance from side to side and front to back.
Figure 9.11 Proper Positioning and Securing of an Appliance
• Shim the appliance as necessary. It is acceptable to use
wood shims underneath the appliance.
• Secure the appliance to the framing by using nails or
screws through the nailing tabs.
• Secure the appliance to the floor by inserting two screws
through the pilot holes at the bottom of the appliance.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
41
10
Installing Vent Pipe (DVP and SLP Pipe)
A. Assemble Vent Sections (DVP Pipe Only)
Attach Vent to the Firebox Assembly
Note: The end of the pipe sections with the lanced tabs will face
toward the appliance.
Attach the first pipe section to the starting collar:
• Lanced pipe end to the starting collar
• Inner pipe over inner collar
• Push the pipe section until all lanced tabs snap in place
• Lightly tug on pipe to confirm it has locked.
Commercial, Multi-family (Multi-level exceeding two stories), or High-Rise Applications
All outer pipe joints must be sealed with silicone with a
minimum of 300ºF continuous exposure rating, including the
slip section that connects directly to the horizontal termination cap.
Figure 10.1 High Temperature Silicone Sealant
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections. See Figure 10.1
A
Lances
• Only outer pipes need to be sealed. All unit collar, pipe,
slip section, elbow and cap outer flues shall be sealed
in this manner, unless otherwise stated.
WARNING! Risk of Fire or Explosion! DO NOT break
silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals
are broken during removal of the termination cap, vent
may leak.
Assemble Pipe Sections
B
Figure 10.3
Figure 10.2
Note: Make sure that the seams are not aligned to prevent
Per Figure 10.2:
unintentional disconnection.
• Start the inner pipe on the lanced end of section A into
the flared end of section B.
• Start the outer pipe of section A over the outer pipe of
section B.
• Once both vents sections are started, push firmly until
all lanced tabs lock into place.
• Lightly tug on the pipe to confirm the tabs have locked.
It is acceptable to use screws no longer than 1/2 in. (13
mm) to hold outer pipe sections together. If predrilling holes,
DO NOT penetrate inner pipe.
CORRECT
For 90º and 45º elbows that are changing the vent direction
from horizontal to vertical, one screw minimum should be
put in the outer flue at the horizontal elbow joint to prevent
the elbow from rotating. Use screws no longer than 1/2
in. (13 mm). If predrilling screw holes, DO NOT penetrate
inner pipe.
Figure 10.4 Seams
42
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
INCORRECT
B. Assemble Vent Sections (SLP Pipe Only)
C. Assemble Slip Sections
To attach the first vent component to the starting collars
of the appliance:
• Slide the inner flue of the slip section into the inner flue of
the pipe section and the outer flue of the slip section over
the outer flue of the pipe section. See Figure 10.6.
• Lock the vent components into place by sliding the pipe
section onto the collar.
• Slide together to the desired length.
• Align the seam of the pipe and seam of collar to allow
engagement. Rotate the vent component to lock into
place. Use this procedure for all vent components. See
Figure 10.5.
• Slide the gasket over the first vent section and place it
flush to the appliance. This will prevent cold air infiltration.
Caulk with a minimum of 300ºF continuous exposure rating
may be used to hold the part in place.
• Continue adding vent components, locking each
succeeding component into place.
Pilot hole
• Ensure that each succeeding vent component is securely
fitted and locked into the preceding component.
Figure 10.6 Slip Section Pilot Holes
Commercial, Multi-family (Multi-level exceeding two stories), or High-Rise Applications
• Maintain a 1-1/2 in. (38 mm) overlap between the slip
section and the pipe section.
For Installation into a commercial, multi-family (multi-level
exceeding two stories) or high-rise applications: All outer
pipe joints must be sealed with silicone with a minimum of
300ºF continuous exposure rating, including the slip section
that connects directly to the horizontal termination cap.
• Secure the pipe and slip section with two screws no
longer than 1/2 in. (13 mm), using the pilot holes in the
slip section. See Figure 10.7.
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections. See Figure 10.1.
• Only outer pipes need to be sealed. All unit collar, pipe,
slip section, elbow and cap outer flues shall be sealed
in this manner, unless otherwise stated.
WARNING! Risk of Fire or Explosion! DO NOT break
silicone seals on slip sections. Use care when removing termination cap from slip pipe. If slip section seals
are broken during removal of the termination cap, vent
may leak.
Figure 10.7 Screws into Slip Section
• Continue adding pipe as necessary following instructions
in “Assembling Pipe Sections.”
NOTICE: If slip section is too long, the inner and outer flues
of the slip section can be cut to the desired length.
Note: Align seams to engage pipe,
then rotate counterclockwise to lock
Figure 10.5 Adding Venting Components
NOTICE: When installing a vent system with an HRC
termination cap, all pipe system joints shall be sealed
using silicone sealant with a minimum of 300ºF continuous
exposure rating.
• Apply a bead of silicone sealant inside the female outer
pipe joint prior to joining sections.
• Only outer pipes are sealed, sealing the inner flue is not
required.
• All unit collar, pipe, slip section, elbow and cap outer
flues shall be sealed.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
43
D. Secure the Vent Sections
E. Disassemble Vent Sections
• Vertical runs of DVP pipe must be supported every 8 ft.
(2.44 m) after the 25 ft. (7.62 m) maximum unsupported
rise.
• Rotate either section (see Figure 10.10) so the seams
on both pipe sections are aligned as shown in Figure
10.11.
• Vertical runs of SLP pipe must be supported every 8 ft.
(2.44 m).
• Pull carefully to separate the pieces of pipe.
• Horizontal sections must be supported every 5 feet
(1.52 m).
• Vent supports or plumbers strap (spaced 120º apart)
may be used to support vent sections. See Figures 10.8
and 10.9.
• Wall shield firestops may be used to provide horizontal
support vent sections.
• SLP ceiling firestops have tabs that may be used to
provide vertical support.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Improper support may allow vent to sag and separate.
Use vent run supports and connect vent sections per installation instructions. DO NOT allow vent to sag below
connection point to appliance.
Figure 10.10 Rotate Seams for Disassembly
120º
Figure 10.11 Align and Disassemble Vent Sections
Figure 10.8 Securing Vertical Pipe Sections
120º
Figure 10.9 Securing Horizontal Pipe Sections
44
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
F. Install Decorative Ceiling Components
(SLP only)
LEVEL
A decorative ceiling thimble can be installed on a flat ceiling through which the vent passes. The decorative ceiling
thimble is used to cover the firestop.
CATHEDRAL CEILING
SUPPORT BOX
• Seal the gap between the vent pipe and firestop using
silicone with a minimum of 300ºF continuous exposure
rating to prevent cold air infiltration.
• Install the decorative ceiling thimble by sliding it up to
the ceiling and attaching it using the provided screws.
A decorative cathedral ceiling support box can be installed
on a cathedral ceiling through which the vent passes.
• Use a plumb-bob to mark the center line of the venting
system on the ceiling and drill a small hole through the
ceiling and roof at this point. Locate the hole and mark
the outline of the cathedral ceiling support box on the
outside roof.
2 in. (51 mm) MIN. BELOW
FINISHED CEILING
CUT HOLE 1/8 in. (3 mm)
GREATER IN SIZE THAN
PATTERN OF SUPPORT
BOX AS IT IS PROJECTED
ONTO ROOF LINE
Figure 10.12
• Remove shingles or other roof covering as necessary
to cut the rectangular hole for the support box. Cut the
hole 1/8 in. (3 mm) larger than the support box outline.
• Lower the support box through the hole in the roof until its
bottom is at least 2 in. (51 mm) below the ceiling (Figure
10.12).
• Level the support box both vertically and horizontally and
temporarily tack it in place through the inside walls into
the roof sheathing.
• Use tin snips to cut the support box from the top corners
down to the roof line and fold the resulting flaps to the
roof. See Figure 10.13.
• Nail the flaps to the roof AFTER running a bead of non
hardening sealant between the flaps and the roof.
Figure 10.13
WARNING! Risk of Fire! Clean out ALL materials from
inside the support box and complete the vertical vent run
and termination.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
45
G. Install Metal Roof Flashing
• See minimum vent heights for various pitched roofs
(Figure 10.14) to determine the length of pipe to extend
through the roof.
CAULK
• Slide the roof flashing over the pipe sections extending
through the roof as shown in Figure 10.15.
HORIZONTAL
OVERHANG
2 FT.
MIN.
20 INCHES MIN.
VERTICAL
WALL
LOWEST
DISCHARGE
OPENING
Figure 10.15
GAS DIRECT VENT
TERMINATION CAP
X
12
ROOF PITCH
IS X/ 12
H (MIN.) - MINIMUM HEIGHT FROM ROOF
TO LOWEST DISCHARGE OPENING
Roof Pitch
H (Min.) Ft.
Flat to 6/12........................................ 1.0*
Over 6/12 to 7/12 ............................ 1.25*
Over 7/12 to 8/12 .............................. 1.5*
Over 8/12 to 9/12 .............................. 2.0*
Over 9/12 to 10/12 ............................. 2.5
Over 10/12 to 11/12 ......................... 3.25
Over 11/12 to 12/12 ........................... 4.0
Over 12/12 to 14/12 ........................... 5.0
Over 14/12 to 16/12 ........................... 6.0
Over 16/12 to 18/12 ........................... 7.0
Over 18/12 to 20/12 ........................... 7.5
Over 20/12 to 21/12 ........................... 8.0
H. Assemble and Install Storm Collar
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.
• Connect both halves of the storm collar with two screws
(see Figure 10.16).
• Wrap the storm collar around the exposed pipe section
closest to the roof and align brackets. Insert a bolt
(provided) through the brackets and tighten the nut to
complete the storm collar assembly. Make sure the collar
is tight against the pipe section.
• Slide the assembled storm collar down the pipe section
until it rests on the roof flashing (see Figure 10.17).
• Caulk around the top of the storm collar (see Figure 10.18).
* 3 foot minimum in snow regions
Figure 10.14 Minimum Height From Roof To Lowest Discharge
Opening
NOTICE: Failure to properly caulk the roof flashing and
pipe seams may permit entry of water.
• Caulk the gap between the roof flashing and the outside
diameter of the pipe.
Figure 10.16 Assembling the Storm Collar
• Caulk the perimeter of the flashing where it contacts the
roof surface. See Figure 10.15.
• Caulk the overlap seam of any exposed pipe sections
that are located above the roof line.
Figure 10.17 Assembling the Storm Collar Around the Pipe
46
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
I. Install Vertical Termination Cap
• Attach the vertical termination cap by sliding the inner
collar of the cap into the inner flue of the pipe section
while placing the outer collar of the cap over the outer
flue of the pipe section.
• Secure the cap by driving three self-tapping screws
(supplied) through the pilot holes in the outer collar of the
cap into the outer flue of the pipe (see Figure 10.18).
TERMINATION CAP
K. Heat Shield Requirements for Horizontal
Termination
WARNING! Risk of Fire! To prevent overheating and fire,
heat shields must extend through the entire wall thickness.
• DO NOT remove the heat shields attached to the
wall shield firestop and the horizontal termination cap
(shown in Figure 10.20).
• Heat shields must overlap 1-1/2 in. (38 mm) minimum.
There are two sections of the heat shield. One section
is factory-attached to the wall shield firestop. The other
section is factory-attached to the cap. See Figure 10.25.
If the wall thickness does not allow the required 1-1/2 in.
(38 mm) heat shield overlap when installed, an extended
heat shield must be used.
• If the wall thickness is less than 4 in./102 mm (DVP)
or 4-3/8 in./ 111 mm (SLP), the heat shields on the cap
and wall shield firestop must to be trimmed. A minimum
1-1/2 in. (38 mm) overlap MUST be maintained.
(1 of 3)
STORM
COLLAR
SCREWS
CAULK
• Use an extended heat shield if the finished wall thickness
is greater than 7-1/4 in. (184 mm).
• The extended heat shield may need to be cut to length
maintaining sufficient length for a 1-1/2 in. (38 mm)
overlap between heat shields.
• Attach the extended heat shield to either of the existing
heat shields using the screws supplied with the extended
heat shield. Refer to vent components diagrams in the
back of this manual.
Figure 10.18
J. Install Decorative Wall Components (SLP
only)
A decorative wall thimble can be installed on wall through
which the vent passes. The decorative wall thimble is used
to cover the wall shield firestop.
• Rest the small leg on the extended heat shield on top
of the pipe section to properly space it from the pipe
section.
Important Notice: Heat shields may not be field constructed.
• Slide the decorative wall thimble over the last section of
horizontal pipe before connecting the termination cap to
the pipe.
• Once the pipe section and the termination cap have been
connected, slide the wall thimble up to the interior wall
surface and attach with screws provided. See Figure
10.19.
Figure 10.19 Wall Thimble
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
47
L. Install Horizontal Termination Cap (DVP
and SLP Pipe)
WARNING! Risk of Fire! The telescoping flue section of
the termination cap MUST be used when connecting vent.
• 1-1/2 (38 mm) minimum overlap of flue telescoping
section is required.
Failure to maintain overlap may cause overheating and
fire.
Note: When using termination caps with factory-supplied
heat shield attached, no additional wall shield firestop is
required on the exterior side of a combustible wall.
HEAT SHIELD OR
EXTENDED
HEAT SHIELD
HEAT SHIELD
1-1/2 IN. (38 MM) MIN.
OVERLAP
WALL SHIELD
FIRESTOP
• Vent termination must not be recessed in the wall. Siding
may be brought to the edge of the cap base.
SLIP SECTION
CAN BE EXTENDED
• Flash and seal as appropriate for siding material at
outside edges of cap.
• When installing a horizontal termination cap, follow
the cap location guidelines as prescribed by current
ANSI Z223.1 and CAN/CGA-B149 installation codes
and refer to Section 6 of this manual.
CAUTION! Risk of Burns! Local codes may require installation of a cap shield to prevent anything or anyone
from touching the hot cap.
NOTICE: For certain exposures which require superior
resistance to wind-driven rain penetration, a flashing kit and
HRC caps are available. When penetrating a brick wall, a
brick extension kit is available for framing the brick.
INNER VENT
SHEATHING
OUTER VENT
INTERIOR
EXTERIOR
VENT DEPTH FROM BACK OF APPLIANCE TO
OUTSIDE SURFACE OF EXTERIOR WALL
(SEE CHART BELOW)
Figure 10.20 Venting through the wall
Termination Cap Specification Chart
(depth without using additional pipe sections)
DVP-TRAPK1 DVP-TRAP1 DVP-TRAPK2 DVP-TRAP2
Top Vent
Rear Vent
Top Vent
Rear Vent
Depth
Depth
Depth
Depth
2-3/4 in. to
3-1/8 in. to
4-7/8 in. to
5-1/4 in. to
4-7/8 in.
5-1/4 in.
9 in.
9-3/8 in.
SL Series
DVP-HPC1
Top Vent
Depth
2-3/4 in. to
4-5/8 in.
DVP-HPC1
Rear Vent
Depth
3-1/8 in. to
5 in.
DVP-HPC2
Top Vent
Depth
5-1/8 in. to
9-1/8 in.
DVP-TRAP1 can adjust 1-1/2 in. (3-1/8 to 4-5/8)
DVP-TRAP2 can adjust 4 in. (5-3/8 to 9-3/8)
DVP-HPC1 can adjust 2-1/8 in. (4-1/4 to 6-3/8)
DVP-HPC2 can adjust 4-1/8 in. (6-3/8 to 10-1/2)
48
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
DVP-HPC2
Rear Vent
Depth
5-1/2 in. to
9-1/2 in.
11
Gas Information
A. Fuel Conversion
C. Gas Connection
• Make sure the appliance is compatible with available gas
types.
• Refer to Reference Section 16 for location of gas line
access in appliance.
• Conversions must be made by a qualified service
technician using Hearth & Home Technologies specified
and approved parts.
• Gas line may be run through knockout(s) provided.
B. Gas Pressure
• Optimum appliance performance requires proper input
pressures.
• Gas line sizing requirements will be determined in ANSI
Z223.1 National Fuel Gas Code in the USA and CAN/
CGA B149 in Canada.
• Pressure requirements are:
Gas Pressure
• The gap between supply piping and gas access hole may
be caulked with caulk with a minimum of 300ºF continuous
exposure rating or stuffed with non-combustible, unfaced
insulation to prevent cold air infiltration.
• Ensure that gas line does not come in contact with outer
wrap of the appliance. Follow local codes.
• Pipe incoming gas line into valve compartment.
• Connect incoming gas line to the 1/2 in. (13 mm)
connection on manual shutoff valve.
WARNING! Risk of Fire or Explosion! Support control
when attaching pipe to prevent bending gas line.
Natural Gas
Propane
Minimum inlet pressure
5.0 in. w.c.
11.0 in. w.c.
• A small amount of air will be in the gas supply lines.
Maximum inlet pressure
14.0 in. w.c.
14.0 in. w.c.
Manifold pressure
3.5 in. w.c.
10.0 in. w.c.
WARNING! Risk of Fire or Explosion! Gas build-up during line purge could ignite.
WARNING! Risk of Fire or Explosion! High pressure
will damage valve. Low pressure may cause explosion.
• Verify inlet pressures. Verify minimum pressures when
other household gas appliances are operating.
• Install regulator upstream of valve if line pressure is
greater than 1/2 psig.
WARNING
Fire Risk.
Explosion Hazard.
High pressure will damage valve.
• Disconnect gas supply piping BEFORE
pressure testing gas line at test pressures
above 1/2 psig.
• Close the manual shutoff valve BEFORE
pressure testing gas line at test pressures
equal to or less than 1/2 psig.
Note: Have the gas supply line installed in accordance with
local codes, if any. If not, follow ANSI 223.1. Installation
should be done by a qualified installer approved and/or
licensed as required by the locality. (In the Commonwealth
of Massachusetts installation must be performed by a
licensed plumber or gas fitter).
Note: A listed (and Commonwealth of Massachusetts approved) 1/2 in. (13 mm) T-handle manual shut-off valve
and flexible gas connector are connected to the 1/2 in. (13
mm) control valve inlet.
• If substituting for these components, please consult
local codes for compliance.
• Purge should be performed by qualified service
technician.
• Ensure adequate ventilation.
• Ensure there are no ignition sources such as sparks
or open flames.
Light the appliance. It will take a short time for air to purge
from lines. When purging is complete the appliance will
light and operate normally.
WARNING! Risk of Fire, Explosion or Asphyxiation!
Check all fittings and connections with a non-corrosive
commercially available leak-check solution. DO NOT use
open flame. Fittings and connections could have loosened during shipping and handling.
WARNING! Risk of Fire! DO NOT change valve settings.
This valve has been preset at the factory.
D. High Altitude Installations
NOTICE: If the heating value of the gas has been reduced,
these rules do not apply. Check with your local gas utility
or authorities having jurisdiction.
When installing above 2000 feet elevation:
• In the USA: Reduce burner orifice 4% for each 1000 feet
above 2000 feet.
• In CANADA: Reduce burner orifice 10% for elevations
between 2000 feet and 4500 feet. Above 4500 feet,
consult local gas utility.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
49
12
Electrical Information
A. Wiring Requirements
C. Optional Accessories Requirements
NOTICE: This appliance must be electrically wired
and grounded in accordance with local codes or, in the
absence of local codes, with National Electric Code
ANSI/NFPA 70-latest edition or the Canadian Electric
Code CSA C22.1.
• This appliance may be used with a wall switch, wall
mounted thermostat and/or a remote control.
• Wire the appliance junction box to 110-120 VAC. This is
required for use of optional accessories.
• A 110-120 VAC circuit for this product must be protected
with ground-fault circuit-interrupter protection, in
compliance with the applicable electrical codes, when
it is installed in locations such as in bathrooms or near
sinks.
• Low voltage and 110 VAC voltage cannot be shared
within the same wall box.
WARNING! Risk of Shock or Explosion! DO NOT wire
110V to the valve or to the appliance wall switch. Incorrect
wiring will damage controls.
Wiring for optional Hearth & Home Technologies approved
accessories should be done now to avoid reconstruction.
Follow instructions that come with those accessories.
D. Electrical Service and Repair
WARNING! Risk of Shock! Label all wires prior to disconnection when servicing controls. Wiring errors can
cause improper and dangerous operation. Verify proper
operation after servicing.
WARNING! Risk of Shock! Replace damaged wire with
type 105º C rated wire. Wire must have high temperature
insulation.
B. Standing Pilot Ignition System Wiring
• The standing pilot ignition system wiring does not require
a 110 VAC supply to operate. See Figure 12.1.
• A 110 VAC junction box MUST be installed for use with
a fan or remote control. See Figure 12.2 for junction box
wiring. Keep wire lengths short as possible.
NOTICE: DO NOT wire 110 VAC to the millivolt valve! This
will damage the valve.
• If using a thermostat use one compatible with a millivolt
gas valve system:
- Install the thermostat in the location as indicated in the
thermostat instructions to ensure proper operation of
appliance.
- Use low resistance thermostat wire for wiring from
ignition system to the wall switch and thermostat.
- Keep wire lengths short as possible.
STANDING
PILOT
REMOTE SWITCH
PIGTAIL
ON
OFF
VALVE
ON/OFF
SWITCH
WHT
RED
Figure 12.1 Standing Pilot Ignition Wiring Diagram
50
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
OPTIONAL WALL SWITCH,
THERMOSTAT OR REMOTE
E. Junction Box Installation
If the box is being wired from the INSIDE of the appliance:
Romex
Connector
• Remove the screw attaching the junction box/receptacle to
the outer shell, rotate the junction box inward to disengage
it from the outer shell (see Figure 12.2).
14/2WG
• Pull the electrical wires from outside the appliance through
the opening into the valve compartment and secure wires
with a Romex connector. See Figure 12.2.
Cover Plate
outside firebox
• Make all necessary wire connections to the junction box/
receptacle and reattach the junction box/receptacle to the
outer shell.
HT
WHT B
LK
BLK
W
Copper
ground attached
to GRN screw with
GRN wire
GRN wire
inside box
NOTICE: DO NOT wire
110 VAC to wall switch.
Figure 12.4 Junction Box Detail
F. Wall Switch Installation for Fan (Optional)
If the box is being wired to a wall mounted switch for use
with a fan (See Figure 12.3):
• The power can then be supplied from the switch box to the
appliance using a minimum of 14-3 with ground wire.
Red
Black
White
Green
Junction Box
• At the switch box connect the black (hot) wire and red
(switch leg) wire to the wall switch as shown.
Switch Box
• At the appliance connect the black (hot), white (neutral)
and green (ground) wires to the junction box as shown.
• Add a 1/4 in. insulated female connector to the red (switch
leg) wire, route it through the knockout in the face of the
junction box, and connect to the top fan switch connector
(1/4 in. male) as shown.
Black
White
Green
Red
Black
White
Green
• The power supply for the appliance must be brought into
a switch box.
Switch
Minimum 14-3 AWG
with Ground
Power
Supply
Wires
Knockout
Red
Figure 12.3 Junction Box Wired to Wall Switch or BC10
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
51
13
Finishing
A. Mantel and Wall Projections
WARNING! Risk of Fire! Comply with all minimum clearances as specified. Framing closer than the minimums listed must be constructed entirely of noncombustible materials
(i.e., steel studs, concrete board, etc.).
3 IN.
MINIMUM
TOP VIEW
Combustible Mantels
All measurements are in inches.
5-3/8 IN.
MINIMUM
CEILING
UNLIMITED
Note: Clearance from opening
to perpendicular wall.
12
11
10
9
Figure 13.3 Wall Projection (Acceptable on one side of opening.)
8
32
7
6
5
4
3
4
5
6
7
8
9
10
11
12
13
3-1/2 in.
NON-COMBUSTIBLE
BOARD SHIPPED
WITH APPLIANCE
TOP OF HOOD OR FIREPLACE OPENING
Figure 13.1 Minimum Vertical and Maximum Horizontal
Dimensions of Combustibles
1/2 in.
Combustible Mantel Legs or Wall Projections
3 IN.
MINIMUM
TOP VIEW
5-3/8 IN.
MINIMUM
3 FT. MAXIMUM
Note: Clearance from opening
to perpendicular wall.
AIR SPACE
Figure 13.4 Non-Combustible Zone
Figure 13.2 Clearances to Mantel Legs or Wall Projections
(Acceptable on both sides of opening.)
52
1/2 in.
SHEETROCK
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
B. Facing Material
• Metal front faces may be covered with non-combustible
materials only.
• Facing and/or finishing materials must not interfere with
air flow through louvers, operation of louvers or doors,
or access for service.
• Facing and/or finishing materials must never overhang
into the glass opening.
• Observe all clearances when applying combustible
materials.
• Seal joints between the finished wall and appliance top
and sides using a 300ºF minimum sealant. Refer to
Figure 13.5.
WARNING! Risk of Fire! DO NOT apply combustible
materials beyond the minimum clearances. Comply with
all minimum clearances to combustibles as specified in
this manual. Overlapping materials could ignite and will
interfere with proper operation of doors and louvers.
FACING MATERIAL UP TO 1/2 IN. THICK
MAY BE COMBUSTIBLE - TOP AND SIDES
NON-COMBUSTIBLE
BOARD (INCLUDED)
0 IN.
1 IN.
1 IN.
1 IN.
0 IN.
0 IN.
HIGH TEMPERATURE (300º F / 149º C MIN.)
TOP & SIDE SEAL JOINT
BOTTOM 1 INCH MAY BE COVERED WITH
COMBUSTIBLE OR NON-COMBUSTIBLE
MATERIAL.
Figure 13.5 Noncombustible Facing Diagram
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
53
14
Appliance Setup
A. Remove Fixed Glass Assembly
E. Ember Placement
See Section 14.G.
WARNING! Risk of Explosion! Follow ember placement
instructions in manual. DO NOT place embers directly over
burner ports. Replace ember material annually. Improperly
placed embers interfere with proper burner operation.
B. Remove the Shipping Materials
Remove shipping materials from inside or underneath the
firebox.
C. Clean the Appliance
Clean/vacuum any sawdust that may have accumulated
inside the firebox or underneath in the control cavity.
D. Accessories
Install approved accessories per instructions included
with accessories. Contact your dealer for a list of approved accessories.
WARNING! Risk of Fire and Electric Shock! Use ONLY
Hearth & Home Technologies-approved optional accessories with this appliance. Using non-listed accessories
could result in a safety hazard and will void the warranty.
Ember material is shipped with this gas appliance. To place
the ember material:
• Embers CANNOT be placed directly over ports. Care
should be taken not to cover the lighting trail of ports
(from back to front).
• Place dime-size pieces of Glowing Embers® just in front
of the port trail, but not on or in between the ports (see
Figure 14.1). Care should be taken so that the ports are
not covered. Failure to follow this procedure will likely
cause lighting and sooting problems.
EMBER MATERIAL
Figure 14.1 Placement of Embers
• Save the remaining ember materials for use during
appliance servicing. The embers provided should be
enough for 3 to 5 applications.
54
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
F. Install the Log Assembly
If the gas logs have been factory installed they should not
need to be positioned. If the logs have been packaged
separately, refer to the following instructions.
2
4
1
Log Set Assembly: LOGS-2014
Model: QV32B-A
5
1
3
STEP 1: Carefully remove the logs from the packaging.
CAUTION: Logs are fragile!
2
STEP 3: LOG #2 (SRV2014-703): Place log # 2 with the left
tip of the log on the flat spot on the burner and the right end
pulled forward against grate.
STEP 2: LOG #1 (SRV2014-701): Place log # 1 centered on the grate and pushed against the back of firebox.
3
STEP 4: LOG #3 (SRV2014-702): Place burned area of log
#3 on the flat spot on the burner, and knob on log resting
on grate.
5
4
3
1
1
STEP 5: LOG #4 (SRV780-707): Place log #4 across log
#3 and resting on log #1.
2
STEP 6: LOG #5 (SRV2014-704): Place log #5 on log #1
and log #2 with burned area facing burner.
2014-925B 6/03
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
55
Install the Log Assembly
If the gas logs have been factory installed they should not
need to be positioned. If the logs have been packaged
separately, refer to the following instructions.
Log Set Assembly: LOGS-2016
Model: QV36B-A
1
1
4
2
5
3
SAME
LOG
STEP 2: LOG #1 (SRV2016-701): Place notches of log #1
on outer two grate tines, and push against back of firebox.
STEP 1: Carefully remove the logs from the packaging.
CAUTION: Logs are fragile!
2
STEP 3: LOG #2 (SRV2014-703): Place log #2 with the
left tip of the log on the flat spot on the burner. Pull the right
part of the log to touch right grate tine, and the top of the log
should rest against log #1.
4
1
2
STEP 5: LOG #4 (SRV780-707): Place log #4 across log #1
and log #2 with burned out area facing out.
56
3
STEP 4: LOG #3 (SRV2014-703): (This log is the same as
log #2). Place log #3 with the flat side down and burned side
into notch on burner. Pull left end forward against grate.
5
3
1
STEP 6: LOG #5 (SRV700-706): Place log #5 across logs
#1 and #3 with the Y-shape facing out.
2016-925B 6/03
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
G. Fixed Glass Assembly
J. Install Hood
WARNING! Risk of Asphyxiation! Handle fixed glass
assembly with care. Inspect the gasket to ensure it is
undamaged and inspect the glass for cracks, chips or
scratches.
The hood is shipped with the front/door.
• DO NOT strike, slam or scratch glass.
• DO NOT operate fireplace with glass removed, cracked,
broken or scratched.
• Replace as a complete assembly.
K. Air Shutter Setting
Air shutter settings should be adjusted by a qualified service technician at the time of installation. The air shutter
is set at the factory for minimum vertical vent run. Adjust
air shutter for longer vertical runs.
Air Shutter Settings
Removing Fixed Glass Assembly
• Pull the four glass assembly latches out of the groove on
the glass frame. Remove glass door from the appliance
(see Figure 14.2).
NG
LP
QV32B-A
1/16 in.
3/8 in.
QV36B-A
1/16 in.
3/8 in.
Replacing Fixed Glass Assembly
• Replace the glass door on the appliance. Pull out and
latch the four glass assembly latches into the groove on
the glass frame.
LATCHES
(BOTH BOTTOM
AND TOP)
GLASS
ASSEMBLY
Figure 14.2 Fixed Glass Assembly
H. Install the Mesh
The screen mesh is shipped with the front/door.
I. Install Trim and/or Surround
• Install optional trim kits and/or surrounds using the
instructions included with the accessory.
• Use non-combustible materials to cover the gap between
the sheet rock and the appliance (when applicable to the
model).
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
57
15
Troubleshooting
With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do
experience a problem, this troubleshooting guide will assist a qualified service technician in the diagnosis of a problem and
the corrective action to be taken. This troubleshooting guide can only be used by a qualified service technician. Contact
your dealer to arrange a service call by a qualified service technician.
A. Standing Pilot Ignition System
Symptom
1. After repeated triggering
of the red or black piezo
ignitor button, the spark
ignitor will not light the
pilot.
2. The pilot will not stay lit
after carefully following
the lighting instructions.
Possible Causes
Corrective Action
A. No gas or low gas pressure.
Check the remote shut-off valves from the appliance. Usually, there
is a valve near the gas main. There can be more than one valve between the appliance and the main.
B. No lp in tank.
Check the LP (propane) tank. You may be out of fuel.
C. Ignitor.
Check the spark at the electrode and pilot. If no spark and electrode
wire is properly connected, replace the ignitor. Verify that there is no
short in electrode wire.
D. Pilot or misaligned electrode
(spark at electrode).
Using match, light the pilot. If the pilot lights, turn off the pilot and
trigger the piezo ignitor button again. If the pilot lights, an improper
gas/air mixture caused the bad lighting and a longer purge period is
recommended. If the pilot will not light, ensure the gap at the electrode and pilot is one-eighth in. to have a strong spark. If the gap is
OK, replace the pilot.
A. Thermocouple.
Check that the pilot flame impinges on the thermocouple. Adjust the
pilot for proper flame impingement.
Ensure that the thermocouple connection at the gas valve is fully inserted and tight (hand tighten plus 1/4 turn).
Verify proper voltage output from the thermocouple to the valve.
Place one millivolt meter lead wire on the thermocouple copper lead.
Place the second lead wire on the solder button on the back of the
valve (blue wire). Start the pilot and hold the valve knob in. The millivolt reading should read 8-16 millivolts. If millivolt reading is less
than 8 millivolts, replace thermocouple.
3. The pilot is burning,
there is no burner
flame, the valve knob is
in the ON position, and
the ON/OFF switch is in
the ON position.
B. Improper gas inlet pressure.
Natural gas should be 5-14 in. w.c. LP should be 10-14 in. w.c. Verify
pressure with manometer.
C. Valve.
If the thermocouple is producing 8-16 millivolts, replace control valve.
A. ON/OFF switch or wires.
Check the ON/OFF switch and wires for proper connections. Place
the jumper wires across the terminals at the ON/OFF switch. If the
burner comes on, replace the ON/OFF switch. If the ON/OFF switch
is OK, place the jumper wires across the ON/OFF switch wires at the
gas valve. If the burner comes on, the wires are faulty or connections
are bad.
B. Thermopile may not be generating sufficient millivoltage.
Check that the pilot flame impinges thermopile properly.
Be sure the wire connections from the thermopile at the gas valve
terminals are tight and that the thermopile is fully inserted into the
pilot bracket.
Check the thermopile with a millivolt meter. Take the reading at THTP&TP terminals of the gas valve. The meter should read 350 millivolts minimum, while holding the valve knob depressed in the pilot
position, with the pilot lit, and the ON/OFF switch in the OFF position.
Replace the thermopile if the reading is below the specified minimum.
With the pilot in the ON position, disconnect the thermopile leads
from the valve. Take a reading at the thermopile leads. The reading
should be 350 millivolts minimum. Replace the thermopile if the reading is below the minimum.
58
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
Troubleshooting (continued)
Symptom
3. (Continued)
Possible Cause
Corrective Action
C. Valve.
Turn the valve knob to the ON position. Place the ON/
OFF switch in the ON position. Take a reading with a
millivolt meter at the thermopile terminals. The millivolt
meter should read greater than 125mV. If the reading
is acceptable, and if the burner does not come on, replace the gas valve.
D. Plugged burner orifice.
Check the burner orifice for stoppage. Remove stoppage.
E. Wall switch or wires.
Check the wall switch and wires for proper connections. Place the jumper wires across the terminals at
the wall switch. If the burner comes on, replace the
wall switch. If the wall switch is OK, place the jumper
wires across the wall switch wires at the gas valve. If
the burner comes on, the wires are faulty or connections are bad.
4. Frequent pilot outage A. Pilot flame may be too high or too low, or blowproblem.
ing out (high pressure), causing pilot safety to
drop out.
Clean thermocouple and adjust the pilot flame for
proper flame impingement. Follow lighting instructions
carefully.
5. The pilot and main
burner extinguish
while in operation.
A. No LP in tank.
Check the LP (propane) tank. Refill the fuel tank.
B. Improper gas inlet pressure.
Natural gas should be 5-14 in. w.c. LP should be 1014 in. w.c. Verify pressure with manometer.
C. Inner vent pipe leaking exhaust gases back
into the system.
Check venting system for damage. Replace/repair improperly assembled pipe sections.
D. Glass installed improperly.
Check to ensure glass is installed properly. Replace
fixed glass panel assembly.
E. Thermopile or thermocouple.
Replace pilot if necessary.
F. Improper vent cap installation.
Check for proper installation and freedom from debris
or blockage.
A. Flame impingement.
Adjust the log set so that the flame does not excessively impinge on it. Refer to log instructions.
B. Improper air shutter setting.
Refer to manual for shutter set points. Ensure that set
point is correct for appliance/gas type. If unit has adjustable shutter, it may be necessary to increase shutter opening.
C. Debris around air shutter.
Inspect the opening at the base of the burner. NO MATERIAL SHOULD BE PLACED IN THIS OPENING.
A. Insufficient oxygen being supplied.
Ensure that the vent cap is installed properly and free
of debris. Ensure that the vent system joints are tight
and have no leaks.
6. Glass soots.
7. Flame burns blue
and lifts off burner.
Ensure that no debris has been placed at the base of,
or in the area of the air holes in the center of the base
pan beneath the burner.
Ensure that the glass is tightened properly on the unit,
particularly on top corners.
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
59
16
Reference Materials
A. Appliance Dimension Diagram
Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5.
O
N
P
M
Q
L
ØR
ØK
GAS LINE ACCESS
C
J
I
E
D
V
H
F
S
B
T
U
A
QV32B-A
Location
Inches
ELECTRICAL
ACCESS
G
QV36B-A
Millimeters
Inches
Millimeters
A
36
913
41
1041
B
31-1/8
791
36-1/8
917
C
27-3/16
691
32-1/16
815
D
18-1/16
459
21-1/2
547
E
31-1/8
790
34-5/8
879
F
3-9/16
90
3-9/16
90
G
6-7/8
174
6-7/8
174
H
23-3/8
594
26-7/8
683
I
34-3/8
873
37-7/8
962
J
35-1/2
902
39-15/16
1015
K
8
203
8
203
L
8-13/16
223
8-13/16
223
M
16-5/16
415
16-5/16
415
N
1/2
13
1/2
13
O
25-3/4
653
30-3/4
781
391
P
12-7/8
326
15-3/8
Q
15-7/8
403
15-7/8
403
R
6-5/8
168
6-5/8
168
S
2-3/16
55
2-3/16
55
T
6
152
6
152
U
1
25
1
25
V
30-1/16
764
33-9/16
853
Figure 16.1 Appliance Dimensions
60
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
B. Vent Components Diagrams
Pipe
DVP4
Effective
Height/Length
DVP Pipe (see chart)
Effective Length
Inches
Millimeters
4
102
10-1/2 in.
(267 mm)
45 °
DVP6
6
152
DVP12
12
305
DVP24
24
610
DVP36
36
914
DVP48
48
1219
10-7/8 in.
(276 mm)
DVP45 (45º Elbow)
4-7/8 in.
( 276 mm)
DVP6A
3 to 6
76 to 152
DVP12A
3 to 12
76 to 305
DVP12MI 3 to 12
76 to 305
DVP24MI 3 to 24
76 to 610
11-3/8 in.
(289 mm)
10 in.
(254 mm)
1 in.
(25 mm)
7-3/8 in.
(187 mm)
1-1/4 in. (32 mm)
10 in.
(254 mm)
9-1/4 in.
(235 mm)
Assembled
Height: 24 in./610 mm
Diameter: 10 in./254 mm
1/2 in. TYP
(13 mm)
13-1/4 in.
(337 mm)
DVP-AS2
DVP-FS (Ceiling Firestop)
DVP90ST (90° Elbow)
12 in.
(305 mm)
1- 1/2 in.
(38 mm)
10 in.
(254 mm)
1 in.
(25 mm)
8 in.
(203 mm)
14 in.
(356 mm)
UP
5 in.
(127 mm)
12 in.
(305 mm)
6 in.
(152 mm)
DVP-HVS (Vent Support)
DVP-WS (Wall Shield Firestop)
Figure 16.2 DVP vent components
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
61
B. Vent Components Diagrams (continued)
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be
used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm) the
existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a DVP-HSM-B
will be required.
8 in.
(203 mm)
Heat
Shield
15-1/8 in.
(384 mm)
Term Cap
Max
Effective
Length
12 in.
(305 mm)
Minimum
Effective Length
Maximum
Effective Length
3-1/8 in.
4-5/8 in.
79 mm
117 mm
5-3/8 in.
9-3/8 in.
137 mm
238 mm
Trap1
DVP-TRAP
Horizontal Termination Cap
Trap2
DVP-TRAP1
DVP-TRAP2
DVP-TRAPK1
DVP-TRAPK2
12 in.
305 mm
7-3/8 in.
(187 mm)
1-1/2 in.
(38 mm)
7-1/4 in.
(184 mm)
12-1/2 in.
(318 mm)
14 in.
(356 mm)
17-3/4 in.
(451 mm)
5-1/4 in.
(133 mm)
DVP-TVHW
VerticalTermination Cap (Highwind)
12 in.
(305 mm)
DVP-TB1
BasementVent Cap
Figure 16.3 DVP vent components
62
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
B. Vent Components Diagrams (continued)
31 in.
(787 mm)
13-1/4 in.
(367 mm)
24-5/8 in.
(625 mm)
27-1/2 in.
(127 mm)
24-5/8 in.
(625 mm)
13-1/4 in.
(367 mm)
RF6M
Roof Flashing Multi-pak
RF12M
Roof Flashing Multi-pak
5 in.
(127 mm)
13-3/4 in.
(349 mm)
11-7/8 in.
(302 mm)
5 in.
(127 mm)
13-7/8 in.
(352 mm)
13-3/4 in.
(349 mm)
DVP-BEK2
DVP-HPC Cap Brick Extension
BEK
Trap Cap Brick Extension
11-5/8 in.
(295 mm)
12-1/8 in.
(308 mm)
7-1/8 in.
(181 mm)
5-3/4 in.
(146 mm)
DVP-TRAPFL
Flashing
13-7/8 in.
(352 mm)
26 in.
660 mm
DVP-HSM-B
Extended Heat Shield
Figure 16.4 DVP vent components
COOL-ADD
Cap Shield
9-1/2 in.
(241 mm)
14 in.
(356 mm)
DRC-RADIUS
Cap Shield
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
63
B. Vent Components Diagrams (continued)
6-1/2 in.
165 mm
6-1/2 in.
165 mm
8-3/4 in.
222 mm
6-1/2 in.
165 mm
9-1/4 in.
235 mm
6 in.
152 mm
6-5/8 in.
168 mm
SLP45
45° Elbow
6-5/8 in.
168 mm
9-7/8 in.
251 mm
SLP90
90° Elbow
Effective Height/Length
Effective
Height/
Length
SLP PIPE
SLP-HVS
Horizontal Pipe
Support
Pipe
inches
mm
SLP4
4
102
SLP6
6
152
SLP12
12
305
SLP24
24
610
SLP36
36
914
SLP48
48
1219
SLP6A
2-6
51-152
SLP12A
2 - 12
51-305
SLP-FLEX-2
24
610
SLP-FLEX-3
36
914
SLP-FLEX-5
60
1524
SLP-FLEX-10
120
3048
SLP-FS
Ceiling Firestop
Figure 16.5 SLP Series Vent Components
64
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
EFFECTIVE HEIGHT/
LENGTH
SLP-FLEX-PIPE
SLP-WS
Wall Shield Firestop
B. Vent Components Diagrams (continued)
Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be
used on a wall 4 in. to 7-1/4 in. (102 mm to 184 mm) thick. If wall thickness is less than 4 in. (102 mm)
the existing heat shields must be field trimmed. If wall thickness is greater than 7-1/4 in. (184 mm) a
DVP-HSM-B will be required.
8 in.
(203 mm)
Heat
Shield
15-1/8 in.
(384 mm)
Term Cap
Max
Effective
Length
12 in.
(305 mm)
Maximum
Effective Length
3-1/8 in.
4-3/4 in.
Trap1
79 mm
121 mm
5-1/4 in.
9-1/4 in.
133 mm
235 mm
Trap2
SLP-TRAP
Horizontal Termination Cap
SLP-SNKD
Snorkel
Termination Cap
Minimum
Effective Length
SLP-CCS-BK
Cathedral Ceiling
Support Box-Black
SLP-TVHW
Vertical
Termination Cap
26 in.
660 mm
DVP-2SL
Adapter
SL-2DVP
Adapter
SLP-DCF-BK
Ceiling Firestop
Black
DVP-HSM-B
Extended Heat Shield
SLP-WT-BK
Wall Thimble-Black
Figure 16.6 SLP Series Vent Components
SLP-FLEX-TRAP
Horizontal
Termination Kit
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
65
B. Vent Components Diagrams (continued)
COAXIAL to COLINEAR VENTING
LINK-DV30B
Flex Liner Kit
DV-46DVA-GCL
Coaxial/Colinear Appliance Connector
Figure 16.7 Coaxial to Colinear Vent Components
66
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12
D. Contact Information
R
Quadra-Fire, a brand of Hearth & Home Technologies Inc.
7571 215th Street West, Lakeville, MN 55044
www.quadrafire.com
Please contact your Quadra-Fire dealer with any questions or concerns.
For the location of your nearest Quadra-Fire dealer,
please visit www.quadrafire.com.
- NOTES ________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
________________________________________________________________________________
NOTICE
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and follow
these instructions for safe
installation and operation.
• Leave this manual with
party responsible for use
and operation.
This product may be covered by one or more of the following patents: (United States) 5328356, 5601073, 5613487,
5647340, 5890485, 5941237, 5947112, 5996575, 6006743, 6019099, 6053165, 6145502, 6170481, 6374822, 6484712,
6601579, 6769426, 6863064, 7077122, 7098269, 7258116, 7470729 or other U.S. and foreign patents pending.
2000-945
Printed in U.S.A. - Copyright 2012
72
Quadra-Fire • QV32B-A, QV36B-A • 2014-900 Rev. U • 1/12