Blackhawk USB200 JTAG Emulator Quick Start Guide

4 CCStudio v5.3 Setup
In the CCS v5.3 Target Configuration General Setup window (see figure 2
below) simply select the Texas Instruments XDS2xx USB Emulator
connection and then check your device or board in the list. Save this setting and launch the TI Debugger.
Blackhawk™
USB200
JTAG Emulator
QUICK
START
GUIDE
(USB200)
XDS200-class JTAG Emulators Require:
Code Composer Studio v5.3† or later††
Install CCSv5.3 or later before connecting the XDS200 hardware!
You will also need:
 PC or Notebook computer with at least one free USB v1.1 or v2.0 port.
 Windows® XP/Vista/7/8* or Linux Operating Systems (32 or 64-bit versions).
*For Windows 8, CCS v5.4 and later is recommended.
Inventory of Items Included
1. Blackhawk USB200 Emulator.
2. USB 2.0 Compliant Cable.
3. 20e_cTI-14t_TI pin converter
4. 20e_cTI-20t_ARM pin converter
5. 20e_cTI-10t_ARM pin converter
6. Warranty and Product Registration
Information.
FIGURE 2 - XDS200 Target Setup and Selection
Follow these links for more details on XDS200 setup using CCStudio:

http://processors.wiki.ti.com/index.php/CCSv5

http://processors.wiki.ti.com/index.php/Target_Configuration__Custom_Configurations
Additional XDS200 Information
Follow this link for more details and support on the XDS200 product:

http://processors.wiki.ti.com/index.php/xds200.
7. Quick Start Guide.
Other Items Required
1. Target Board System — a selfpowered board with a TI DSP and
compatible JTAG header connection
conforming to IEEE 1149.1 Standard.
2. Copy of Code Composer Studio
†
v5.3 or later.
4
Blackhawk is a registered trademark of EWA Technologies, Inc.
USB200-QS-01
This equipment is designed to
be operated under the following environmental conditions:
Temperature between 0°C –
55°C. Relative Humidity of
20% - 70% non-condensing.
Operation of the unit outside of
the above range may affect
structual and mechanical
integrity and cause permanent
damage.
Caution is necessasry to
minimize ESD (Electro-static
Discharge) which can damage
electronic components. Use in
a controlled environment
where ESD materials and
practices are employed is
highly recommended.
† If running CCS v5.2, you MUST update to the latest TI Emulation package using:
Help->Check for Updates. This not a Blackhawk update.
††
Blackhawk
123 Gaither Drive, Mt. Laurel, NJ 08054-1701
www.blackhawk-dsp.com
IMPORTANT
ENVIRONMENTAL
CONSIDERATIONS
CCStudio v5.3 is available for 90-day download or purchase from TI for use with
XDS200 products. Please visit these TI Wiki pages for more information:
1
http://processors.wiki.ti.com/index.php/CCSv5
1 Emulation Driver Installation
Code Composer Studio v5.3** or later
Must be Installed FIRST
USB PnP Installation 3
Windows XP/Vista/7/8
1.
Install Code Composer Studio v5.3 or later FIRST. DO NOT ATTACH EMULATOR HARDWARE UNTIL CCSv5 IS INSTALLED.
Complete step 1, then if not already connected, connect the USB cable to the
computer and to the USB200 emulator.
XDS200 Drivers are installed as part of CCSv5.3 or later. These files are
supplied by TI. By default, the drivers are installed to the following folder:
2.
For more information on the XDS200 and CCS v5, refer to the TI documentation and help resources and the following links:
3.
4.
5.
If prompted, follow the Windows “Found New Hardware” wizard prompts.
You can select the “automatic” option for locating drivers.
When completed, the Windows Device Manager will show the USB200 device
under the Ports (COM &LPT) as XDS2xx Emulator CDC Serial Port
(COM##) and XDS2xx User CDC Serial Port (COM##).
6.
Now follow the Code Composer Studio Setup—Section 4.
C:\ti\ccsv5\ccs_base\emulation\windows\xds2xx_drivers
http://processors.wiki.ti.com/index.php/CCSv5
http://processors.wiki.ti.com/index.php/XDS200
** If using CCS v5.2, you must first update the “TI Emulation” feature to the latest
version for XDS200 support (Help->Check for Updates). This is a TI CCS update you need, not a Blackhawk update.
Linux (32 and 64-bit)
1.
2.
2 Hardware Installation
Install Code Composer Studio v5.3 or later FIRST. DO NOT ATTACH EMULATOR HARDWARE UNTIL CCSv5 IS INSTALLED.
Complete step 1, then if not already connected, connect the USB cable to the
computer and to the USB200 emulator.
3. Run the Linux command, lsusb, in a terminal window and verify the device in
WARNING
Be careful to connect interface connector with the correct orientation.
Pin 1 on the interface cable should match Pin 1 on the DSP system
connector. The JTAG cable assembly features a "keyed" connector to
minimize the chance of error.
listed the output. For example:
Bus 001 Device 002: ID 0451:bef0 Texas Instruments, Inc.
4. Now follow the Code Composer Studio Setup—Section 4.
USB200 JTAG Controller
Do not force connector into position. Forcing them may damage the
connector or the interconnected boards and systems.
USB Mini-B Connector
1. Install Code Composer v5.3 or later software FIRST.
DO NOT AT-
TACH EMULATOR HARDWARE UNTIL CCS v5 IS INSTALLED.
2. Complete step 1, then attach the USB cable to an available USB port on
the PC.
3. Then attach the other end of the USB cable (mini-B connector) to the
USB Mini-B connector of the USB200 Emulator (see Figure 1).
4. Follow the Plug and Play installation for the Windows device driver (see
section 3 on USB PnP Installation for more information).
5. Connect the emulator’s 20-pin socket to the proper adapter fitting your
target header (see figure 1).
Make sure the target board is not powered when connecting!
6. Setup and start Code Composer Studio (see section 4).
2
Left LED
Right LED
ON when emulator
is booted or ready
for emulation.
Flashes during
emulation driver
activity
OFF on target
connect
1
3
2
20-pin keyed JTAG Connector
1. works with 20e_cTI-14t_TI Pin Converter (included)
2. works with 20e_cTI-20t_ARM Pin Converter (included)
3. works with 20e_cTI-10t_ARM Pin Converter (included)
FIGURE 1 - USB200 JTAG Emulator (multiple views)
3