Gold Medal 5021 ET, T, 5024 ET, 5025 ET, 5038, 5042, 5044 ET, T, 5051 ET, 5055 ET Countertop Baker Instruction Manual

Gold Medal 5021 ET, T, 5024 ET, 5025 ET, 5038, 5042, 5044 ET, T, 5051 ET, 5055 ET Countertop Baker Instruction Manual

Below you will find brief information for Countertop Baker 5021 ET, Countertop Baker 5021 T, Countertop Baker 5024 ET, Countertop Baker 5025 ET, Countertop Baker 5038. The Countertop Baker is a countertop unit designed to bake waffles. It features a timer, a power switch, and a temperature control for the baking grids. The unit is easy to use and clean, and it comes with a warranty covering defects in material and workmanship.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

Countertop Baker 5021 ET, 5021 T, 5024 ET, 5025 ET, 5038 - Instruction Manual | Manualzz
Part No. 76023
Countertop Baker Unit
Instruction Manual
Models 5021, 5021ET, 5021T, 5024, 5024ET, 5025, 5025ET,
5038, 5042, 5044, 5044ET, 5040T, 5051, 5051ET, 5055ET
Standard and Electronic
Cincinnati, OH 45241-4807 USA
SAFETY PRECAUTIONS
Checking Shipment:
Unpack all cartons and check thoroughly for any damage that may have occurred during
transit. Damage claims should be filed immediately with the transportation company. Gold
Medal is not responsible for damage that occurs in transit.
Setup:
Remove all packing material and tape before starting operation.
Electrical Requirements:
The following power supply must be provided:
Round grid Models require a 120VAC, 60Hz. 15 amp electrical outlet.
Square grid Models require a 120VAC, 60Hz. 20 amp electrical outlet.
Your electrician must furnish sufficient current for proper machine operation. We
recommend this machine be on a dedicated and circuit protected line. Failure to wire
properly will void the warranty and can result in damage to the heat elements, light, motor
and etc.
It is Gold Medal Products Company’s recommendation that this machine be plugged
directly into a wall outlet. The use of extension cords is not recommended due to safety
risks and the baker’s performance will be sacrificed/reduced.
Before You Plug In Machine:
1. Make sure that the wall outlet can accept the three (3) prong grounded plug on the
power supply cord.
2. The wall outlet must have the proper polarity. If in doubt, have a competent electrician
inspect the outlet and correct if necessary.
3. DO NOT use a three (3) prong grounded to two (2) prong un-grounded adapter.
3
Model #5021, # 5024, #5025, #5038, #5042, #5044, #5051, #5055ET
Machine Operation
Grid Seasoning
1. Turn the timer to 6 minutes (See page 6 for electronic timer instructions,) turn the power
switch to the “ON” position to allow the unit to pre-heat.
2. Open grids and lightly spray the Seas'n-Kleen on the grid surfaces.
3. Using the handles, rotate the grid assembly 180 degrees clockwise until the positive stop
engages. Turn the timer to 3 minutes.
4. If sticking occurs repeat above procedure.
(Note: Coated grids do not need to be seasoned. Do not use metallic utensils on coated
grids.)
.
Belgian Waffle Maker Operation
1. Pre-heat the grids by turning the timer to 6 minutes (See page 6 for electronic timer instructions)
and turn the power switch to the “ON” position. Keep the grids closed and allow the unit to heat
untill the GREEN ready light goes out.
2. Open grid assembly and season lightly with Seas'n-Kleen. Pour the desired amount of
batter into the lower grid. Be careful not to overfill grid with batter.
3. Close the top grid and rotate the grid assembly 180 degrees clockwise until the positive lock
stop is engaged.
4. Turn timer knob to approximately three minutes. Some testing will be necessary to
determine the appropriate cooking time.
5. When the buzzer sounds rotate the grid assembly 180 degrees counter clockwise until the
the positive stop lock engages. Open the grids and remove the waffle.
6. Keep the grids closed between baking periods for best baking performance. Use a soft
bristled brush to remove any waffle residue from grids while baking.
7. Grids should be re-seasoned as needed during baking and after each cleaning.
4
Model #5021, # 5024, #5025, #5038, #5042, #5044, #5051, #5055ET
General Instructions (Standard Machine)
1. Always use fresh batter and do not allow it to warm up too much.
2. Frequent cleaning with a soft-bristled brush, and re-seasoning the grids as needed
during operation, will ensure a great tasting product.
3. Leave the grids in the closed position whenever possible because open grids cause
excessive carbon build-up.
4. If the baker is on for over an hour with no baking, lightly brush Free-N-Easy (Gold Medal
Item #2250QT) on the grids before baking.
5. Never apply beeswax, paraffin, or any other waxes to grid surfaces.
Removing Excess Carbon
1.
2.
3.
4.
5.
6.
7.
8.
Make sure appliance is cool and dry.
Un-plug machine from outlet.
Place a shallow drip pan under the grids.
Open top grid and spray a generous portion of Kleen-Sweep (Gold Medal Item #
2173CN) on grids, and allow to soak for at least a 1/2 hour. See Kleen-Sweep warning
below.
Using a bristle brush, do a general scrubbing on all grid surfaces that had Kleen-Sweep
applied to them. Using a spray bottle, spray GRIDS ONLY with cold water to rinse away
Kleen-Sweep.
Scrub grid surfaces with warm-soapy water (also applied with spray bottle) to remove
remaining Kleen-Sweep.
Use a damp cloth or sponge to wipe down the rest of the baker, to remove any splatter.
Re-season grids as described in GRID SEASONING section on previous page.
5
Models: 5021, 5021ET, 5021T, 5024, 5024ET, 5025, 5025,
5038, 5042, 5044, 5044ET, 5044T, 5051, 5051ET, 5055ET
Instructions for Changing Cooking Time and Temperature Set Point:
Upon powering up, wait until heat indicator turns “OFF” before loading with
product. Press and hold “SET” for 3 seconds to toggle the display between time
and grid temperature.
To Change Cook Time:
1. Press “SET” and “DN” for 3 seconds to display the time setting (X:XX, min:secs
will be flashing.)
2. Press “UP” to increase the time setting. “DN” will decrease the time setting.
3. Press “SET” again to save the time setting.
To Change Temperature Set Point:
1. Press “SET” and “UP” for 3 seconds to the display the temperature set point
(XXX°F symbol flashing.)
2. Press “UP” to increase the temperature set point. “DN” will decrease the
temperature set point.
3. Press “SET” again to save the temperature set point.
6
Models: 5021, 5021ET, 5021T, 5024, 5024ET, 5025, 5025,
5038, 5042, 5044, 5044ET, 5044T, 5051, 5051ET, 5055ET
MAINTENANCE INSTRUCTIONS
ORDERING SPARE PARTS
1. Identify the needed part by checking it against the photos, illustrations, and/or the parts list.
2. When ordering, please include part number, part name, and quantity needed.
3. Please include the machine’s model name, serial number, and date of manufacture (located on
the machine nameplate) with your order.
4. Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
(800) 543-0862
(513) 769-7676
Fax: (513) 769-8500
or, place orders at:
E-mail: [email protected]
Web Page: www.gmpopcorn.com
8
Models: 5021, 5021ET, 5021T, 5024, 5024ET, 5025, 5025,
5038, 5042, 5044, 5044ET, 5044T, 5051, 5051ET, 5055ET
STANDARD GENERAL BAKER EXPLODED VIEW (Refer to parts list)
Baker Handle
P/N 76074
Toggle Switch Boot
P/N 76382
Toggle Switch
P/N 47201
Switch Panel Decal
(Round Grid)
P/N 76309
(Square Grid)
P/N 76197
Hinge Pin
P/N 76056
Top Support Assembly
(Round Grid)
P/N 76244
(Square Grid)
P/N 76146
Hinge Nut
P/N 76130
Drip Pan
P/N 76104
Pilot Light - Green
P/N 41469
Front Support Assembly
P/N 76145
Pilot Light - Red
P/N 41033
Timer Knob
P/N 76301
Interval Timer
P/N 76300
Conduit
P/N 76651-11
Wire Harness
P/N 76558
(5021 Only)
P/N 76557
Thermostat
P/N 76054
(5042 Only)
P/N 76557
Element Clamp
P/N 76072
9
Pivot Block Assy.
P/N 76065
Steel Tab
P/N 76070
Pivot Cam
P/N 76069
Lead-In Cord
(Round Grid)
P/N 22038
(Square Grid)
P/N 87085
Models: 5021, 5021ET, 5021T, 5024, 5024ET, 5025, 5025,
5038, 5042, 5044, 5044ET, 5044T, 5051, 5051ET, 5055ET
ELECTRONIC GENERAL BAKER EXPLODED VIEW
Overlay
P/N 76549
Rocker Switch
P/N 42798
Digital Baker Control
P/N 76540A
Rocker Switch Cover
P/N 48786
Mount Screw
P/N 76190
Push Button
P/N 41031
Tinnerman Nut
P/N 76081
Push Button Boot
P/N 38324
Instruction Label
P/N 76540A
Digital Baker Control
P/N 76540A
Heat Sink
P/N 48673
Thermocouple Wires
P/N 76346
Relay
P/N 76542
10
Models: 5021, 5021ET, 5021T, 5024, 5024ET, 5025, 5025,
5038, 5042, 5044, 5044ET, 5044T, 5051, 5051ET, 5055ET
PARTS LIST – NOT SHOWN
Round Grid
Models
Square Grid
Models
Part No.
Part No.
76145
10096
76192
47328
49123
76026
76145
10096
76192
47328
49123
Description
76048
76226
74153
67060
76048
76147
74153
Front Support Assembly
Front Support Glides (Inside Support
Scrub Brush (Not Shown)
Glide (Not Shown)
Crutch Tip (Not Shown)
Strain Relief, #SR-6P3-4 (Round Grid)
or
#SR-7W-2 (Square Grid)
Bottom Plate
Bottom Support Assembly
8-32 X 1” Thermostat Mounting Screw
82135
87315
76333
82135
87315
76333
Conduit Bushing
Silicon Sleeving, 3/8"
Removal Knob (5042 Only)
Specific Model Part
Model No.
Waffle Grid Waffle Grid
w/Coating
Waffle Grid
with Stop
Heat
Element
Element
Support
Data Plate
Grid Cover
#5021, ET, T
76043
76043T
76042
76553
n/A
76059
76049
#5024, ET
76159
76159
76154
76554
76189
76156
76137
#5025, ET
76374
76374
76375
76381
76189
76376
76137
#5038
76253
76253
76252
76554
76189
76254
76137
76285
(Retainer)
76299
(Grid Insert)
76553
76189
76289
76298
#5042
76284
76284
(Retainer)
(Retainer)
76299
76299
(Grid Insert) (Grid Insert)
#5044, ET, T
76263
76263T
76264
76554
76189
76266
76137
#5051, ET
76383
76383
76384
76381
76189
76385
76137
#5055ET
NA
76399T
76400T
76554
76189
76387
76137
11
Models: 5021, 5021ET, 5021T, 5024, 5024ET, 5025, 5025,
5038, 5042, 5044, 5044ET, 5044T, 5051, 5051ET, 5055ET
Wiring Diagram (Standard)
12
Models: 5021, 5021ET, 5021T, 5024, 5024ET, 5025, 5025,
5038, 5042, 5044, 5044ET, 5044T, 5051, 5051ET, 5055ET
Wiring Diagram (Electronic)
13
Models: 5021, 5021ET, 5021T, 5024, 5024ET, 5025, 5025,
5038, 5042, 5044, 5044ET, 5044T, 5051, 5051ET, 5055ET
WARRANTY
WE WARRANT to the original purchaser the Gold Medal equipment sold by us to
be free from defects in material or workmanship under normal use and service. Our
obligation under this warranty shall be limited to the repair or replacement of any
defective part for a period of six (6) months from the date of sale to the Original
Purchaser with regard to labor and two (2) years with regard to parts and does not
cover damage to the equipment caused by accident, alteration, improper use, voltage,
abuse, or failure to follow instructions.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED
OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR
PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF. We neither assume, nor authorize any other person
to assume for us, any other obligation or liability in connection with the sale of said
GOLD MEDAL equipment or any part thereof.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that
person, firm, association, or corporation who was billed by the GOLD MEDAL
PRODUCTS COMPANY, or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS COMPANY AT 1-800543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE
EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS
CONCERNING THE REPAIR OR REPLACEMENT OF PARTS.
GOLD MEDAL PRODUCTS COMPANY
10700 Medallion Drive
Cincinnati, Ohio 45241-4807 USA
www.gmpopcorn.com
Phone: 1-800-543-0862
Fax: 1-800-542-1496
© The text, descriptions, graphics and other material in this publication are the proprietary
and exclusive property of Gold Medal Products Company and shall not be used, copied,
reproduced, reprinted or published in any fashion, including website display, without its
express written consent.

advertisement

Key Features

  • Timer
  • Power switch
  • Temperature control
  • Easy to use
  • Easy to clean
  • Warranty

Frequently Answers and Questions

What are the electrical requirements for the countertop baker?
Round grid models require a 120VAC, 60Hz, 15 amp electrical outlet. Square grid models require a 120VAC, 60Hz, 20 amp electrical outlet. It is recommended to plug the machine directly into a wall outlet.
How do I season the grids on the countertop baker?
Turn the timer to 6 minutes, turn the power switch to “ON” to preheat the unit. Open the grids and lightly spray Seas'n-Kleen on the grid surfaces. Rotate the grid assembly 180 degrees clockwise until the positive stop engages. Turn the timer to 3 minutes. If sticking occurs, repeat the procedure.
How do I clean the countertop baker?
Make sure the appliance is cool and dry. Unplug the machine from the outlet. Place a shallow drip pan under the grids. Open the top grid and spray a generous portion of Kleen-Sweep on the grids, and allow to soak for at least a 1/2 hour. Scrub the grid surfaces with a bristle brush. Rinse away the Kleen-Sweep with cold water. Scrub the grid surfaces with warm-soapy water. Wipe down the rest of the baker with a damp cloth or sponge. Re-season the grids as described in the GRID SEASONING section.
What are the dimensions of the countertop baker?
The exact dimensions can be found in the document where it describes the product's parts.

Related manuals

Download PDF

advertisement