FD-2200

FD-2200
Technical Service Instructions
FD-2200
SI-5GE0B
Front derailleur
General Safety Information
WARNING
• Obtain, read and carefully service instructions when installing parts. A loose, worn,
or damaged parts may cause injury to the rider.
We strongly recommend that only genuine Shimano replacement parts be used.
• Be careful not to let the cuffs of your clothes get caught in the chain while riding,
otherwise you may fall off the bicycle.
• Read these Technical Service Instructions carefully, and keep them in a safe place for
later reference.
Note
• If gear shifting operations cannot be carried out smoothly, clean the derailleur and
lubricate all moving parts.
• If the amount of looseness in the links is so great that adjustment is not possible, you
should replace the derailleur.
• When the chain is in the position shown in the
illustration, the chain may contact the front
Front chainrings
chainrings or front derailleur and generate noise.
If the noise is a problem, shift the chain onto the
next-larger rear sprocket or the one after.
• For smooth operation, always be sure to use the
specified outer casing and the bottom bracket
Rear sprockets
cable guide.
• Grease the inner cable and the inside of the
outer casing before use to ensure that they slide
properly.
• Parts are not guaranteed against natural wear or deterioration resulting from normal
use.
• For maximum performance we highly recommend Shimano lubricants and
maintenance products.
• For any questions regarding methods of installation, adjustment, maintenance or
operation, please contact a professional bicycle dealer.
In order to realize the best performance, we recommend that the following
combination be used.
Shifting lever
ST-3300
Outer casing
SP40
Gears
16
Front derailleur
FD-2200
Front chainwheel
FC-2200
Bottom bracket
BB-UN25 (110mm)
Rear derailleur
RD-2200
Freehub
Cassette sprocket
FH-2200
CS-HG50-8
Chain
CN-HG50
Bottom bracket cable guide
SM-SP17
Specifications
Type
Front derailleur
installation band diameter
Band type / Brazed on type
S (28.6mm), M (31.8mm)
Chainstay angle (C)
61° - 66°
Chain line
43.5mm
t
Installation of the front derailleur
1. Adjust so that the clearance between the chain guide
outer plate and the large gear is 1 - 3 mm before
installing.
Clearance: 1 - 3 mm
SG
A-53
Chain guide outer plate
2. The level section of the chain guide outer plate should be
directly above and parallel to the largest chainring.
3. Secure using a 5mm Allen key.
Chainwheel
(largest chainring)
Chain guide
Tightening torque:
5 - 7 N·m
{44 - 60 in. lbs.}
SIS adjustment
1. Low adjustment
Set so that the clearance between the
chain guide inner plate and the chain is
0-0.5 mm.
B A
Largest
sprocket
Low
adjustment
screw
Inner ring
B
A
Chain guide
inner plate
Chain
2. Connection and securing of cable
While pulling the inner cable, tighten the wire fixing bolt
with a 5 mm allen key to secure the cable.
Tightening torque: 5 - 7 N·m
{44 - 60 in. lbs.}
After taking up the initial slack in
the cable, re-secure to the front
derailleur as shown in the
illustration.
Pull
3. Top adjustment
Set so that the clearance between the
chain guide outer plate and the chain
is 0-0.5 mm.
B A
Smallest
sprocket
Top
adjustment
screw
Outer ring
B
A
Chain guide
outer plate
Chain
4. Adjustment of the cable
tension
■ Front shifting (ST-3300)
(1) Set the chain to the largest
rear sprocket, and shift the
front to top gear.
Largest
sprocket
Lever [
b
From large
chainring to
small chainring
Outer ring
Lever [
a
Lever [
a
(2) Perform the trimming.
From small
chainring to
large chainring
■ Trimming (noise-prevention
mechanism)
Gently press the lever [
b.
(A “click” sound will be heard.)
(3) After trimming, adjust the clearance (by using the cable-adjustment bolt) of
the chain and chain guide yo the minimum (0-0.5mm).
Largest
sprocket
Outer ring
B
Chain guide
inner plate
B
A
A
Clearance:
0 - 0.5mm
Chain
Outer casing adjustment bolt
Be sure to read these service instructions in conjunction with the service instructions for
the ST-3300 before use.
®
One Holland Irvine CA 92618 U.S.A. Phone 949-951-5003
Industrieweg 24 NL-8071 CT Nunspeet Holland Phone 31-341-272222
77 Oimatsu-cho 3-cho Sakai Osaka 590-8577 Japan
Please note: specifications are subject to change for improvement without notice. (English)
© Dec. 2002 by Shimano Inc. XBC SZK Printed in Singapore.
t
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement