SUNNEN ANR 275 Remote-Feed Hone INSTALLATION & OPERATING INSTRUCTIONS

I-ANR-275D
http://www.sunnen.com
INSTALLATION & OPERATING INSTRUCTIONS
for
SUNNEN® ANR-275 REMOTE-FEED HONE
Includes Repair Parts List
GENERAL
POWER SOURCE
The ANR-275 Hone has been designed to hone bores
from 2.50 to 21.00 in. (64 - 533 mm) diameter.
Use heavy duty electric drill in a honing rig, or drill
press (see Figure 1). To establish optimum rpm for
your application, divide 800 by the hole diameter in
inches.
Example: 800 + 4" = 200 (rpm); or divide 20,000
by the hole diameter in Millimeters.
Example: 20,000 + 100mm = 200 (rpm).
NOTE: For light work in bores larger than 10 in.
(254 mm) in diameter.
INSTALLATION
The Remote-Feed Hones are designed for use in a
rigid installation, such as a drill press or a honing
rig, where part to be honed and power source are
rigidly fixed (see Figure 1). The ANR-275 is
equipped with two Universal Joints which allow
the honing head to align itself with the workpiece.
Hole Size
Recommended Drill
2.5 to 5 in. (63 - 130mm) . . . . 5/8 in. (15mm) capacity
5 to 15 in. (130 - 380mrn) . . . . . 3/4" (19mm) capacity
15 in. up (380mm up) . . . . . . . . 1" (25mm) capacity
FIGURE 1, Honing Rig
SUNNEN ® PRODUCTS COMPANY • 7910 MANCHESTER ROAD • ST. LOUIS, MO 63143, U.S.A. • PHONE: 314-781-2100
HONING OIL
Use a continuous and ample flow of Sunnen
Industrial Honing Oil to ensure accurate, fast honing
and freedom from galling or scratches. Do not
dilute the oil. Do not use lubricating oil, cutting oil,
or water soluble oil; consistent results cannot be
expected unless the full-strength recommended oil
is used.
ASSEMBLY OF STONES AND GUIDES
1. Pull back Release Ring and tilt hone body as
shown (see Figure 2).
2. Pull the ANR-210 Pinion all the way out.
3. Place the racks of the stone and guide assemblies
in holes marked "X" as shown.
FIGURE 2, Assembly
4. Put ANR-2l0 Pinion back in place.
5. Pull back Release Ring, line up hone body, and
allow Release Ring to return to engaged position.
CAUTION
Do not mix used stones and guides from different
sets - the guides will be either too tight or too loose,
causing chatter, poor cutting, or other undesirable
results.
TO HONE HOLE
To hone workpiece, proceed as follows (see Figure
3):
1. Place hone in work.
2. Expand stones by rotating handwheel in a
counterclockwise direction (opposite to direction of
hone rotation). When hone contacts wall of work,
back handwheel off one-half turn clockwise.
FIGURE 3, Handwheel
5. As bore diameter gets larger and stones become
loose, a light braking on the handwheel will keep
the stones cutting.
CAUTION
Hone must rotate in a clockwise direction (as viewed
from power source end).
STROKING
Stroke the hone fast enough to produce a crosshatch
pattern in the hole. At the end of each stroke the
stones should extend approximately one inch (25mm)
out of the cylinder.
3. Start hone rotating in work in a clockwise
direction and apply very light stopping pressure to
handwheel as hone is stroked through length of bore.
4. Localize honing in any tight spots and gradually
lengthen stroke as bore becomes straighter.
2
TABLE 1, Operational Troubleshooting Guide
CONDITION TO BE CORRECTED
CHATTER
STONE
NOT
CUTTING
STONE GLAZED*
Stone surface looks
clean but cutting
grains are dulled
(Honing dial
needle moves
too slowly)
STONE LOADED*
Stone surface looks
smeared and
clogged with chips
SLOW STOCK REMOVAL*
(Honing dial needle moves too slowly)
POOR STONE LIFE*
(Honing dial needle moves too fast)
BELLMOUTH
Standard Sunnen Tooling and Procedures will satisfy all ordinary honing requirements. If problems are encountered, they can usually
be solved by following procedure suggested below. For detailed information on difficult or unusual honing problems contact
your local Sunnen Field Engineer or Sunnen Customer Service Department in St. Louis, Missouri, USA.
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
Very RPM and
Relieve Guides
Reduce cutting
Switch to guideless stone
stroke rate
1/32” (1mm)
pressure
set, unless bore has
keyway or is larger than
8” (203mm) in diameter
Sharpen A or J stone
Increase cutting
Increase stroking
Use a softer stone
Check oil to be
with MAN-700
pressure
speed
(one with a lower
sure you are using
diamond dresser; use
hardness number)
Sunnen Industrial
LBN-700 dressing stick
Honing Oil*
on all other stones
Clean stone with
Increase stroking
Use a softer stone
Use a coarser grit
Check oil to be
LBN-700 dressing
pressure
(one with a lower
stone (one with a
sure you are using
stick
hardness number)
lower grit number)
Sunnen Industrial
Honing Oil*
Increase spindle speed
Increase cutting
Check oil to be
Use a softer stone
Use a coarser grit
pressure
sure you arc using
(one with a Lower
stone (one with a
Sunnen Industrial
hardness number)
lower grit number)
Honing Oil*
Decease cutting
Use faster spindle
(one with higher
stone (one with lower
Check oil to be sure
pressure
speed
hardness number
grit number)
you are using Sunnen
Industrial Honing Oil*
True stone and shoes
Use softer stone
If Bore is LONGER
Shorten STONE only
If bellmouth persists
with truing sleeve
(OK with lower
than 2/3 stone length:
(or row of stones)
shorten stones still
If part is short or
hardness number)
slightly on both ends
more but do not shorten
unbalanced, shorten
shoes any further
stroke length
If Bore is SHORTER
Shorten STONES and
CAUTION:
than 2/3 stone length:
SHOES equally to
Overcorrection of
1-1/2 times bore
bellmouth will lead
length
to barrel condition
True stone and shoes
Use finer grit stone
Use longer stone or
Use mandrel with
CAUTION:
with truing sleeve
(one with higher grit
shorten guide shoes
longer stone and shoe
Overcorrection of
number)
on both ends
barrel will lead
to bellmouth condition
{
{
BARREL
TAPER IN
OPEN HOLE
True stone and shoes
with truing sleeve
TAPER IN
BLIND HOLE
Shorten stone and
If hole has insufficient
shoes to about 3/4
or no relief at bottom,
shorten stone more
use hard tip stone
if taper persists
Make sure honing
Thoroughly true stone
If thin wall part,
tool is recommended
and shoes to exact
decrease cutting
size for diameter to
hole diameter
pressure
be honed
Use honing tool with sufficient stone length to bridge waviness
(or Iands and ports in bore)
Use L, BL, or multi-stone mandrel. Stone
Use shorter stroke
length should be at least 1-1/2 times the
length
length of bore for best bow correction
(less overstroke)
OUT-OF-ROUND
WAVINESS
RAINBOW
Change stroke so tight
end of bore is stroked
over stone further
True stone and shoes
frequently with truing
sleeve
Reverse work on
mandrel more often
If power stroking, make
sure spindle and stroker
are in alignment
Provide sufficient
relief at bottom of
hole
Provide adequate oil
flow at bottom of hole
to wash cutting out
If stone stops cutting
at decreased pressure
use stone with lower
hardness number
If power stroking
make sure spindle
and stroker are in
alignment
Use stone with lower
hardness number to
avoid part flexing
FINISH TOO ROUGH*
Decrease cutting
pressure
Use finer grit stone
(one with higher grit
number)
Check oil to be sure
you are using Sunnen
Industrial Honing Oil*
Thoroughly true shoes
to exact hole diameter
RANDOM SCRATCHES
(in bore)
Decrease cutting
pressure
Use finer grit stone
(one with higher grit
number)
Use softer stone
(one with lower
hardness number)
If hard steel mandrel is
being used, change to
soft steel mandrel. If
soft steel mandrel or
shoes are being used,
change to bronze
mandrel or shoes
For extremely fine
finishes in soft or
exotic material, use
bronze mandrel or
bronze shoes
Check oil to be
sure you are using
Sunnen Industrial
Honing Oil*
*Many honing problems, such as poor cutting action, poor stone life, and rough finish are caused by wrong honing oil, insufficient honing oil, dirty honing oil, or
contaminated honing oil. Use only clean, full-strength Sunnen Industrial Honing Oil. Make sure that honing oil is neither diluted or "cut" with other oils. Keep solvents
and cleaning fluids away from honing machine.
3
ANR-275 Remote-Feed Hone
4
PARTS LIST
ITEM
NO.
1
2
3
4
5
6
7
8
9
10
10A
10B
11
12
13
14
15
16
14
17
17A
18
N/S
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
14
ORDER BY
PART
NUMBER
AN-670
AN-608A
AN-665A
AN-640A
ANR-1 10A
ANR-156A
ANR-1 17A
ANR-135A
ANR-142C
ANR-144A
ANR-143A
ANR-141A
ANR-125A
ANR-1 16A
ANR-145A
MSN-177A
ANR-230A
ANR-231A
MSN-177A
ANR-235A
PHP-202A
PHS-132A
KN-575A
ANR-160A
ANR-207A
ANR-170A*
ANR-189A*
ANR-195A*
ANR-176A*
ANR-187A*
ANR-165A*
ANR-210A
AN-620A
AN-621A
AN-624A
AN-623A
--AN-604
MSN-177A
DESCRIPTION
QTY.
1
1
1
1
1
1
2
1
1
2
2
2
1
1
1
4
1
1
4
1
1
1
1
1
2
1
2
1
1
1
1
1
1
2
2
2
1
1
4
....Heavy Duty Universal Joint Assembly consists of:
......Drive Shaft Assembly
......Universal Joint
......Extension Coupler
....Upper Feed Assembly consists of:
......Drive Head
......Bearings (1" Diameter Nylon)(Pkg. of 2)
......Sun Gear (with one Pin Item 9)
......Shear Pin (1/8" Dia. Steel, .610" length)(Pkg. of 2)
......Gears (.402 Thick, .189 bore diameter)(Pkg. of 2)
......Gears (.125 Thick, .251 bore diameter)(Pkg. of 2)
......Gears (.402 Thick, .251 bore diameter)(Pkg. of 2)
......Feed Shaft Assembly
......Carriage Assembly with Dowel Pins and Bearing
......Hand Wheel Assembly with Gear
......Screws (10-32 x 5/8" SHCS)(Pkg. of 4)
....Feed Clutch consists of:
......Housing
......Screws (10-32 x 5/8" SHCS)(Pkg. of 4)
......Clutch Assembly with
........Pin (1/8" Dia. Steel)(Pkg. of 2)
......Setscrew
......5/32" Hex Key Wrench (5/32'" Across Flats)
....Hone Head Assembly consists of:
......Setscrews, Self-Locking (Pkg. of 2)
......Inner Feed Assembly consists of:
........Drive Pin (3/16" Dia. Steel)(Pkg. of 2)
........Feed Shaft End Assembly, Spring and Pin
........Coupling
........Ball Link Assembly
......Drive Housing Assembly
......Pinion Adjustment Assembly
....Ring Set consists of:
......Screws (Pkg. of 2)
......Screws (Pkg. of 2)
......Spacers (Pkg. of 2)
......Ring
......Body Assembly
......Screws (10-32 x 5/8" SHCS)(Pkg. of 4)
N/S indicates Not Shown
*The ANR-275A Setscrews (Item #20 are included with this part. DO NOT reuse old setscrews for safety reasons.
NOTE: If you are frequently replacing gears (Item 10, 10A or 10B) and your carriage assembly (Item 12) does not use four gears of
equal thickness, we recommend ordering a new ANR-116A Carriage Assembly which includes four gears of equal thickness.
5
RECOMMENDED STONE SETS
FOR HOLES
WITHOUT
KEYWAYS
GENERAL PURPOSE STONE SETS
(2 STONES AND 2 GUIDES)
HOLE DIAMETERS
DEBURRING in Rough Holes
All Materials
FOR HOLES
WITH
KEYWAYS
KEYWAY STONE SETS
MAXIMUM KEYWAY WIDTH
.8in.
.9in.
1.2in.
1.4in.
GUIDELESS STONE SETS
Approx.
Surface
Finish
in Microinches
2.5-2.7 in. 2.7-4.1 in. 3.5-5.5 in. 4.1-21*in. 2.5-3.3 in. 3.3-4.2 in. 4.0-5.6 in. 4.5-9.2*in. 2.5-3.3 in. 3.3-4.2 in. 4.0-5.6 in. 4.5-21.2*in.
(64-69mm)
(69-104mm) (89-140mm) (104533mm) (64-84mm)
(84107mm) (102-142mm) (114-234mm) (64-80mm) (84-107mm) (102-142mm) (114-538mm)
G25-A47
M27-A47
N37-A47
W47-A47 GG25-A47 MM33-A47 NN40-A47 WW51-A47 GY25-A47 MY33-A47 NY40-A47 WY51-A47
FAST STOCK REMOVAL in Deburred
Bored, Ground, or Reamed Holes
Aluminum
G25-145
M27-J45
N37-J45
W47-J45 GG25-J45 MM33-J45 NN40-J45 WW51-J45 GY25-J45 MY33-J45 NY40-J45 WY51-J45
Brass, Soft
G25-363
M27-J63
N37-J63
W47-J63 GG25-J45 MM33-J45 NN40-J45 WW51-J45 GY25-J45 MY33-J45 NY40-J45 WY51-J45
80
Bronze
G25-J45
M27-J45
N37-J45
W47-J45 GG25-J45 MM33-J45 NN40-J45 WW51-J45 GY25-J45 MY33-J45 NY40-J45 WY51-J45
80
Carbide
•
•
•
Cast Iron
G25-J45
M27-J45
N37-J45
Ceramic
•
•
•
Glass
•
•
•
Steel, Soft
G25-A45
M27-A45
N37-A45
•
•
•
•
•
•
•
•
80
•
W47-J45 GG25-J45 MM33-J45 NN40-J45 WW51-J45 GY25-J45 MY33-J45 NY40-J45 WY51-J45
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
32
W47-A45 GG25-A45 MM33-A45 NN40-A45 WW51-A45 GY25-A45 MY33-A45 NY40-A45 WY51-A45
35
20
Steel, Hardened (try this stone first)
G25-A45
M27-A45
N37-A45
W47-A45 GG25-A45 MM33-A45 NN40-A45 WW51-A45 GY25-A45 MY33-A45 NY40-A45 WY51-A45
Steel, Hardened (it A45 does not cut)
G25-A43
M27-A43
N37-A43
W47-A43 GG25.A43 MM33-A43 NN40-A43 WW51-A43 GY25-A43 MY33-A43 NY40-A43 WY51-A43
20
Steel, Very Hard Tool (if A43 does not cut)τ
G25-J63
M27-J63
N37-J63
W47-J63 GG25-J45 MM33-J45 NN40-J45 WW51-J45 GY25-J45 MY33-J45 NY40-J45 WY51-J45
12
15
FINE FINISHING in Previously Honed Holes
τ
Aluminum
G25-J87
M27-J87
N37-J87
W47-J87 G025-J87 MM33-J87 NN40-J87 WW51-J87 GY25-J87 MY33-J87 NY40-J87 WY51-J87
Brass, Soft
G25-J85
M27-J85
N37-J85
W47-J85 GG25-J85 MM33-J85 NN40-J85 WW51-J85 GY25-J85 MY33-J85 NY40-J85 WY51-J85
15
Bronze
G25-J87
M27-J87
N37-J87
W47-J87 GG25-J87 MM33-J87 NN40-J87 WW51-J87 GY25-J87 MY33-J87 NY40-J87 WY51-J87
15
Carbide
•
•
•
Cast Iron
G25-J87
M27-J87
N37-J87
Ceramic
•
•
•
•
•
•
•
•
•
•
•
W47-J87 GG25-J87 MM33-J87 NN40-J87 WW51-J87 GY25-J87 MY33-J87 NY40-J87 WY51-J87
•
•
•
•
•
•
•
•
6
Glass
•
•
•
G25-J85
M27-J85
N37-J85
W47-J85 GG25-J85 MM33-J85 NN40-J85 WW51-J85 GY25-J85 14Y33-J85 NY40-J85 WY51-J85
S
Steel, Soft
G25-J87 M27-J87
Diamond and CBN/Borazon stones available on special order.
N37-J87
W47-J87 GG25-J87 MM33-J87 NN40-J87 WW51-J87 GY25-J87 MY33-J87 NY40-J87 WY51-J87
7
6
•
•
Steel, Hard
* These stones require Master Holders
•
•
COMPLETE LIST OF ALL AVAILABLE STONE SETS
COMPLETE LISTING OF ALL STONES AVAILABLE FROM STOCK. (In some cases, stones other than those recommended above may hone faster or last longer. For long or repetitive production runs, it
may be economical to choose a stone slightly harder or softer, coarser or finer. If the stone wears out too fast, use a harder stone; if it Goes not cut, use a softer stone.)
FOR HOLES
WITHOUT
KEYWAYS
GENERAL PURPOSE STONE SETS
(2 STONES AND 2 GUIDES)
(64-69mm)
(69-104mm) (89-140mm) (104533mm) (64-84mm)
Grit Size
(84107mm) (102-142mm) (114-234mm) (64-80mm) (84-107mm) (102-142mm) (114-538mm)
*
SOFT
N37-A23
80(2)
*
*
W47-A23 GG25-A23 MM33-423 NN40-A23 WW51-A23
M27-A25
N37-425
W47-A25 GG25-A25 MM33-A25 NN40-A25 WW51-A25
M27-A27
N37-A27
W47-A27 GG25-A27 MM33-A27 NN40-A27 WW51-A27
G25-A43
M27-A43
N37-A43
W47-A43 GG25-A43 MM33-A43 NN40-A43 WW51-A43 GY25-A43 MY33-A43 NY40-A43 WY51-A43
G25-A45
M27-A45
N37-A45
W47-A45 GG25-A45 MM33-A45 NN40-A45 WW51-A45 GY25-A45 MY33-A45 NY40-A45 WY51-A45
G25-A47
M27-647
N37-A47
W47.A47 GG25-A47 MM33-A47 NN40-A47 WW51-A47 GY25-A47 MY33-A47 NY40-A47 WY51-A47
HARD
G25-A49
M27-A49
N37-A49
W47-A49
SOFT
G25-A63
M27-A63
N37-A63
W47-A63
G25-A65
M27-A65
N27-A65
W47-A65 GG25-A65 MM33-A65 NN40-A65 WW51-A65 GY25-A65 MY33-A65 NY40-A65 WY51-A65
G25-A67
M27-A67
N27-A67
HARD
Oxide
GUIDELESS STONE SETS
2.5-2.7 in. 2.7-4.1 in. 3.5-5.5 in. 4.1-21*in. 2.5-3.3 in. 3.3-4.2 in. 4.0-5.6 in. 4.5-9.2*in. 2.5-3.3 in. 3.3-4.2 in. 4.0-5.6 in. 4.5-21.2*in.
HOLE DIAMETERS
Aluminum
FOR HOLES
WITH
KEYWAYS
KEYWAY STONE SETS
MAXIMUM KEYWAY WIDTH
.8in.
.9in.
1.2in.
1.4in.
SOFT
150(4)
`
280(6)
HARD
M27-A69
SOFT
70(1)
150(4)
GY25-A67 MY33-A67 NY40-A67 WY51-A67
M27-J11
N37-J11
W47-J11
G25-J13
M27-J13
N37-J13
W47-J13 GG25-J13 MM33-J13 NN40-J13 WW51-J13
G25-J15
M27-J15
N37-J15
W47-J15 GG25-J15 MM33-J15 NN40-J15 WW51-J15
WY51-J15
G25-J17
M27-J17
N37-J17
W47-J17 GG25-J17 MM33-J17 NN40-J17 WW51-J17
WY51-J17
W47-J19
HARD
SOFT
W47-467
W47-A69
M27-J19
N37-J19
G25-J43
M27-J43
N37-J43
W47-J43 GG25-J43 MM33-J43 NN40-J43 WW51-J43
G25-J45
M27-J45
N37-J45
W47-J45 GG25-J45 MM33-J45 NN40-J45 WW51-J45 GY25-J45 MY33-J45 NY40-J45 WY51-J45
M27-J47
N37-J47
W47-J47
W47-J49
G25-J47
NN40-J47
WY51-J43
GY25-J47 MY33-J47 NY40-J47 WY51-J47
M27-J48
HARD
Silicon
Carbide
M27-J49
N37-J49
G25-J63
M27-J63
N37-J63
W47-J63
MM33-J63
G25-J65
M27-J65
N37-J65
W47-J65
MM33-J65
HARD
G25-J67
M27-J67
N37-J67
W47-J67
MM33-J67
SOFT
G25-J83
M27-J83
N37-J83
W47-J83
G25-J85
M27-J85
N37-J85
W47-J85 GG25-J85 MM33-J85 NN40-J85 WW51-J85 GY25-J85 MY33-J85 NY40-J85 WY51-185
G25-J87
M27-J87
N37-J87
W47-J87 GG25-J87 MM33-J87 NN40-J87 WW51-J87 GY25-J87 MY33-J87 NY40-J87 WY51-187
SOFT
280(6)
400(8)
HARD
500(9)
WW51-J67 GY25-J67 MY33-J67 NY40-J67 WY51-J67
NN40-J83 WW51-J83
M27-J89
G25-J95
M27-J95
N37-J95
W47-J95 GG25-J95 MM33-J95
G25-J97
M27-J97
N37-J97
W47-J97
600(0)
τ
WW51-J65 GY25-J65 MY33-J65 NY40-J65 WY51-J65
WW51-J95
GG25-C05 MM33-C05 NN40-C05 WW51-C05
Diamond and CBN/Borazon stones available on special order.
* These stones require Master Holders
7
MY33-J95
Approx.
Surface
Finish
in Microinches
FRACTION / DECIMAL / MILLIMETER EQUIVALENTS CHART
INCH
FRACTION
DECIMAL
MILLIMETER
INCH
FRACTION
DECIMAL
MILLIMETER
INCH
FRACTION
DECIMAL
MILLIMETER
....
.003937
0,1000
9/32
.281250
7,1438
21/32
.656250
16,6688
....
.007874
0,2000
19/64
.296875
7,5406
....
.669291
17,0000
....
.011811
0,3000
5/16
.312500
7,9375
43/64
.671875
17,0656
1/64
.015625
0,3969
....
.314961
8,0000
11/16
.687500
17,4625
....
.015748
0,4000
21/64
.328125
8,3344
45/64
.703125
17,8594
....
.019685
0,5000
11/32
.343750
8,7313
....
.708661
18,0000
....
.023622
0,6000
....
.354331
9,0000
23/32
.718750
18,2563
....
.027559
0,7000
23/64
.359375
9,1281
47/64
.734375
18,6531
1/32
.031250
0,7938
3/8
.375000
9,5250
....
.748031
19,0000
....
.031496
0,8000
25/64
.390625
9,9219
3/4
.750000
19,0500
....
.035433
0,9000
....
.393701
10,0000
49/64
.765625
19,4469
....
.039370
1,0000
13/32
.406250
10,3188
25/32
.781250
19,8438
3/64
.046875
1,1906
27/64
.421875
10,7156
....
.787402
20,0000
1/16
.062500
1,5875
....
.433071
11,0000
51/64
.796875
20,2406
5/64
.078125
1,9844
7/16
.437500
11,1125
13/16
.812500
20,6375
....
.078740
2,0000
29/64
.453125
11,5094
....
.826772
21,0000
3/32
.093750
2,3813
15/32
.468750
11,9063
53/64
.828125
21,0344
7/64
.109375
2,7781
....
.472441
12,0000
27/32
.843750
21,4313
....
.118110
3,0000
31/64
.484375
12,3031
55/64
.859375
21,8281
1/8
.125000
3,1750
1/2
.500000
12,7000
....
.866142
22,0000
9/64
.140625
3,5719
....
.511811
13,0000
7/8
.875000
22,2250
5/32
.156250
3,9688
33/64
.515625
13,0969
57/64
.890625
22,6219
....
.157480
4,0000
17/32
.531250
13,4938
....
.905512
23,0000
11/64
.171875
4,3656
35/64
.546875
13,8906
29/32
.906250
23,0188
3/16
.187500
4,7625
....
.551181
14,0000
59/64
.921875
23,4156
....
.196850
5,0000
9/16
.562500
14,2875
15/16
.937500
23,8125
13/64
.203125
5,1594
37/64
.578125
14,6844
....
.944882
24,0000
7/32
.218750
5,5563
....
.590551
15,0000
61/64
.953125
24,2094
15/64
.234375
5,9531
19/32
.593750
15,0813
31/32
.968750
24,6063
....
.236220
6,0000
39/64
.609375
15,4781
....
.984252
25,0000
1/4
.250000
6,3500
5/8
.625000
15,8750
63/64
.984375
25,0031
17/64
.265625
6,7469
....
.629921
16,0000
1
1.000000
25,4000
....
.275591
7,0000
41/64
.640625
16,2719
1-1/16
1.062500
26,9880
FORMULAS:
MULTIPLY
INCHES (in)
FEET (ft)
x
x
BY
25.4
0.3048
=
=
TO GET
MILLIMETERS (mm)
METERS (m)
MULTIPLY
MILLIMETERS (mm)
METERS (m)
x
x
BY
0.03937
3.281
=
=
TO GET
INCHES (in)
FEET (ft)
“SUNNEN AND THE SUNNEN LOGO ARE REGISTERED TRADEMARKS OF SUNNEN PRODUCTS COMPANY.”
Sunnen® reserves the right to change or
revise specifications and product design
in connection with any feature of our
products contained herein. Such changes
do not entitle the buyer to corresponding
changes, improvements, additions, or
replacements for equipment, supplies or
accessories previously sold. Information
contained herein is considered to be
accurate based on available information
at the time of printing. Should any
discrepancy of information arise, Sunnen
recommends that user verify discrepancy
with Sunnen before proceeding.
PRINTED IN U.S.A.
0609
SUNNEN PRODUCTS LIMITED
No. 1 Centro, Maxted Road
Hemel Hempstead, Herts HP2 7EF ENGLAND
Phone: ++ 44 1442 39 39 39
Fax: ++ 44 1442 39 12 12
www.sunnen.co.uk
e-mail: [email protected]
SUNNEN AG
SUNNEN PRODUCTS COMPANY
7910 Manchester Road, St. Louis, MO 63143 U.S.A.
Phone: 314-781-2100
Fax: 314-781-2268
U.S.A. Toll-Free Sales and Service –
Automotive: 1-800-772-2878 • Industrial: 1-800-325-3670
International Division Fax: 314-781-6128
Fabrikstrasse 1
8586 Ennetaach-Erlen, Switzerland
Phone: ++ 41 71 649 33 33
Fax: ++ 41 71 649 34 34
www.sunnen.ch
e-mail: [email protected]
SHANGHAI SUNNEN MECHANICAL CO., LTD.
889 Kang Qiao East Road, PuDong
Shanghai 201319, P.R. China
Phone: 86 21 5 813 3322
Fax: 86 21 5 813 2299
www.sunnensh.com
e-mail: [email protected]
SUNNEN ITALIA S.R.L.
http://www.sunnen.com
e-mail: [email protected]
Viale Stelvio 12/15
20021 Ospiate di Bollate (MI) Italy
Phone: 39 02 383 417 1
Fax: 39 02 383 417 50
www.sunnenitalia.com
e-mail: [email protected]
©COPYRIGHT SUNNEN® PRODUCTS COMPANY 2006, ALL RIGHTS RESERVED