Vauxhall Astra 2012.5 car Owner's Manual
Below you will find brief information for Astra 2012.5. The Astra 2012.5 is a car with a range of features that make it a great choice for drivers of all levels of experience. It is equipped with a start-stop system that helps to save fuel and reduce emissions. The Astra 2012.5 also includes a variety of safety features, such as airbags, seat belts, and traction control.
advertisement
Owner’s Manual
Model Year 2012.5
Edition: January 2012
TS 1680-B-12
VAUXHALL Astra
Contents
Introduction .................................... 2
In brief ............................................ 6
Keys, doors and windows ............ 19
Seats, restraints ........................... 35
Storage ........................................ 53
Instruments and controls ............. 91
Lighting ...................................... 126
Climate control ........................... 137
Driving and operating ................. 145
Vehicle care ............................... 181
Service and maintenance .......... 226
Technical data ........................... 229
Customer information ................ 255
Index .......................................... 258
2 Introduction
Introduction
Vehicle specific data
Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate.
Introduction
Your vehicle is a designed combination of advanced technology, safety, environmental friendliness and economy.
This Owner's Manual provides you with all the necessary information to enable you to drive your vehicle safely and efficiently.
Make sure your passengers are aware of the possible risk of accident and injury which may result from improper use of the vehicle.
You must always comply with the specific laws and regulations of the country that you are in. These laws may differ from the information in this
Owner's Manual.
When this Owner's Manual refers to a workshop visit, we recommend your
Vauxhall Authorised Repairer. For gas vehicles, we recommend a Vauxhall Authorised Repairer licensed to service gas vehicles.
All Vauxhall Authorised Repairers provide first-class service at reasonable prices. Experienced mechanics trained by Vauxhall work according to specific Vauxhall instructions.
The customer literature pack should always be kept ready to hand in the vehicle.
Using this manual
■ This manual describes all options and features available for this model. Certain descriptions, including those for display and menu functions, may not apply to your vehicle due to model variant, country specifications, special equipment or accessories.
■ The "In brief" section will give you an initial overview.
Introduction 3
■ The table of contents at the beginning of this manual and within each section shows where the information is located.
■ The index will enable you to search for specific information.
■ This Owner's Manual depicts lefthand drive vehicles. Operation is similar for right-hand drive vehicles.
■ The Owner's Manual uses the factory engine designations. The corresponding sales designations can be found in the section
"Technical data".
■ Directional data, e.g. left or right, or front or back, always relate to the direction of travel.
■ The vehicle display screens may not support your specific language.
■ Display messages and interior labelling are written in bold letters.
4 Introduction
Danger, Warnings and
Cautions
9 Danger
Text marked 9 Danger provides information on risk of fatal injury.
Disregarding this information may endanger life.
9 Warning
Text marked 9 Warning provides information on risk of accident or injury. Disregarding this information may lead to injury.
Caution
Text marked Caution provides information on possible damage to the vehicle. Disregarding this information may lead to vehicle damage.
Symbols
Page references are indicated with 3.
3 means "see page".
Thank you for choosing a Vauxhall.
We wish you many hours of pleasurable driving.
Your Vauxhall Team
Introduction 5
6
In brief
In brief
Initial drive information
Vehicle unlocking Seat adjustment
Seat positioning
Press button c to unlock the doors and load compartment. Open the doors by pulling the handles. To open the tailgate, push the touchpad switch below the handle.
Radio remote control 3 20, Central
Pull handle, slide seat, release handle.
Seat position 3 37, Seat adjustment
9 Danger
Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment.
Seat backrests Seat height Seat inclination
In brief 7
Pull lever, adjust inclination and release lever. Allow the seat to engage audibly.
Seat position 3 37, Seat adjustment
Lever pumping motion up = seat higher down = seat lower
Seat position 3 37, Seat adjustment
Lever pumping motion up = front end higher down = front end lower
Seat position 3 37, Seat adjustment
8 In brief
Head restraint adjustment Seat belt Mirror adjustment
Interior mirror
Press the button, adjust height and engage.
Pull out the seat belt and engage in belt buckle. The seat belt must not be twisted and must fit close against the body. The backrest must not be tilted back too far (maximum approx. 25 °).
To release belt, press red button on belt buckle.
Seat position 3 37, Seat belts
To reduce dazzle, adjust the lever on the underside of the mirror housing.
Interior mirror 3 29, Automatic antidazzle interior mirror 3 29.
Exterior mirrors Steering wheel adjustment
In brief 9
Select the relevant exterior mirror and adjust it.
Electric adjustment 3 28, Folding exterior mirrors 3 28, Heated
Unlock the lever, adjust the steering wheel, then engage the lever and ensure it is fully locked.
Do not adjust the steering wheel unless the vehicle is stationary and the steering wheel lock has been released.
10 In brief
Instrument panel overview
1
Power windows ..................... 30
2
Exterior mirrors ..................... 28
3
Cruise control ..................... 162
4
Side air vents ...................... 143
5 Turn and lane-change signals, headlight flash,
low beam and high beam ... 131
Exit lighting ......................... 135
Parking lights ...................... 132
Driver Information Centre .... 109
6
Instruments .......................... 98
7
Steering wheel controls ....... 91
8
Driver Information Centre .... 109
9 Windscreen wiper, windscreen washer system, headlight washer system, rear wiper, rear
washer system ...................... 93
10 Central locking system .......... 21
Hazard warning flashers .... 131
Control indicator for airbag
deactivation ........................ 103
Control indicator for front
passenger seat belt ........... 103
Fuel selector ......................... 99
11 Info-Display ........................ 112
12 Anti-theft alarm system
status LED ........................... 25
13 Centre air vents .................. 143
14 Glovebox .............................. 53
15 Sport mode ........................ 160
Tour mode .......................... 160
Traction Control system ..... 159
Electronic Stability Control . 159
Parking assist ..................... 163
Lane departure warning ..... 168
Eco button for stop/start
system ................................. 148
16 Climate control system ........ 137
17 AUX input, USB input .......... 10
18 Power outlet .......................... 97
In brief 11
19 Selector lever, manual
transmission ....................... 155
Automatic transmission ...... 152
20 Ignition switch with
steering wheel lock ............ 146
21 Horn ..................................... 92
Driver airbag ........................ 44
22 Bonnet release lever .......... 183
23 Storage compartment,
fuse box ............................. 201
24 Steering wheel adjustment . . 91
25 Light switch ........................ 126
Headlight range
adjustment ......................... 128
Front fog lights ................... 132
Rear fog light ...................... 132
Instrument illumination ....... 133
12 In brief
Exterior lighting Headlight flash, high beam and low beam
Turn light switch:
7 = lights off
8 = sidelights
9 = headlights
Automatic light control
AUTO = automatic light control:
Headlights are switched m on and off automatically
= activation or deactivation
8
9 of the automatic light control
= sidelights
= headlights
Fog lights
Press light switch:
> = front fog lights r = rear fog light
headlight flash = pull lever high beam low beam
= push lever
= push or pull lever
Automatic light control 3 127, High
beam 3 127, Headlight flash 3 128,
Adaptive forward lighting 3 129.
Turn and lane-change signals Hazard warning flashers Horn
In brief 13
lever up = right turn signal lever down = left turn signal
Turn and lane-change signals
Operated with the ¨ button.
Hazard warning flashers 3 131.
Press j.
14 In brief
Washer and wiper systems
Windscreen wiper
Windscreen and headlight washer systems
Rear window wiper and washer systems
2 = fast
1 = slow
P = timed interval wiping or automatic wiping with rain sensor
§ = off
For a single wipe when the windscreen wiper is off, press the lever down.
Pull lever.
Windscreen and headlight washer
system 3 93, Washer fluid 3 185.
Press the rocker switch to activate the rear window wiper: upper position lower position middle position
= continuous operation
= intermittent operation
= off
Rear window wiper/washer 3 95.
Climate control
Heated rear window, heated exterior mirrors
In brief
Demisting and defrosting the windows
15
Push lever.
Washer fluid is sprayed on the rear window and the wiper wipes a few times.
The heating is operated by pressing the Ü button.
Press button V.
Set the temperature control to the highest level.
Cooling n on.
Heated rear window Ü on.
16 In brief
Transmission
Manual transmission
Automatic transmission
Reverse: with the vehicle stationary, wait 3 seconds after depressing clutch pedal and then press the release button on the selector lever and engage the gear.
If the gear does not engage, set the lever to neutral, release the clutch pedal and depress again; then repeat gear selection.
P = park
R = reverse
N = neutral
D = drive
Manual mode: move selector lever from D to the left.
< = higher gear
] = lower gear
The selector lever can only be moved out of P when the ignition is on and the brake pedal is applied. To engage
P or R, press the release button.
Starting off
Check before starting off
■ Tyre pressure and condition 3 206,
■ Engine oil level and fluid levels
■ All windows, mirrors, exterior lighting and number plates are free from dirt, snow and ice and are operational.
■ Proper position of mirrors, seats,
■ Brake function at low speed, particularly if the brakes are wet.
Starting the engine
■ Turn key to position 1
■ move the steering wheel slightly to release the steering wheel lock
■ operate clutch and brake
■ automatic transmission in P or N
■ do not operate accelerator pedal
■ diesel engines: turn the key to position 2 for preheating and wait until control indicator !
extinguishes
■ turn key to position 3 and release
Stop-start system
If the vehicle is at a low speed or at a standstill and certain conditions are fulfilled, activate an Autostop as follows:
■ Depress the clutch pedal
■ set the lever in neutral
■ release the clutch pedal
An Autostop is indicated by the needle at the AUTOSTOP position in the tachometer.
To restart the engine, depress the clutch pedal again.
In brief 17
Parking
■ Always apply the parking brake.
Activate the manual parking brake without pressing the release button.
Apply as firmly as possible on a downhill slope or uphill slope.
Depress foot brake at the same time to reduce operating force.
For vehicles with electrical parking brake, pull switch m.
■ Switch off the engine. Turn the ignition key to position0 and remove it. Turn the steering wheel until the steering wheel lock is felt to engage.
For vehicles with automatic transmission, the key can only be removed when the selector lever is in the P position.
■ If the vehicle is on a level surface or uphill slope, engage first gear or set the selector lever to P before switching off the ignition. On an uphill slope, turn the front wheels away from the kerb.
If the vehicle is on a downhill slope, engage reverse gear or set the
18 In brief
selector lever to P before switching off the ignition. Turn the front wheels towards the kerb.
■ Lock the vehicle with button e on the radio remote control.
Activate the anti-theft alarm system
■ Do not park the vehicle on an easily ignitable surface. The high temperature of the exhaust system could ignite the surface.
■ Close the windows and the sunroof.
■ The engine cooling fans may run after the engine has been switched
■ After running at high engine speeds or with high engine loads, operate the engine briefly at a low load or run in neutral for approx. 30 seconds before switching off, in order to protect the turbocharger.
Keys, locks 3 19, Laying the vehicle
up for a long period of time 3 181.
Keys, doors and windows
Keys, locks ................................... 19
Doors ........................................... 24
Vehicle security ............................ 25
Exterior mirrors ............................ 28
Interior mirrors ............................. 29
Windows ...................................... 30
Roof ............................................. 33
Keys, locks
Keys
Replacement keys
The key number is specified in the
Car Pass or on a detachable tag.
The key number must be quoted when ordering replacement keys as it is a component of the immobiliser system.
Lock cylinders
Designed to free-wheel if they are forcefully rotated without the correct key or if the correct key is not fully inserted. To reset, turn cylinder with the correct key until its slot is vertical, remove key and then re-insert it. If the cylinder still free-wheels, turn the key through 180° and repeat operation.
Keys, doors and windows
Key with foldaway key section
Press button to extend. To fold the key, first press the button.
Car Pass
The Car Pass contains security related vehicle data and should therefore be kept in a safe place.
When the vehicle is taken to a workshop, this vehicle data is needed in order to perform certain operations.
19
20 Keys, doors and windows
Radio remote control
Used to operate:
■ Central locking system
■ Anti-theft locking system
■ Anti-theft alarm system
■ Power windows
■ Sunroof
The radio remote control has an approximate range of up to
20 metres. It can be restricted by external influences. The hazard warning flashers confirm operation.
Handle with care, protect from moisture and high temperatures and avoid unnecessary operation.
Fault
If the central locking system cannot be operated with the radio remote control, it may be due to the following:
■ Range exceeded
■ Battery voltage too low
■ Frequent, repeated operation of the radio remote control while not in range, which will require resynchronisation
■ Overload of the central locking system by operating at frequent intervals, the power supply is interrupted for a short time
■ Interference from higher-power radio waves from other sources
Basic settings
Some settings can be changed in the menu Settings in the Info-Display.
Vehicle personalisation 3 121.
Radio remote control battery replacement
Replace the battery as soon as the range reduces.
Batteries do not belong in household waste. They must be disposed of at an appropriate recycling collection point.
Key with foldaway key section
Extend the key and open the unit.
Replace the battery (battery type
CR 2032), paying attention to the installation position. Close the unit and synchronise.
Radio remote control synchronisation
After replacing the battery, unlock the door with the key in the driver's door lock. The radio remote control will be synchronised when you switch on the ignition.
Memorised settings
Whenever the key is removed from the ignition switch, the following settings are automatically memorised by the key:
■ Lighting
■ Infotainment system
■ Central locking system
■ Sport mode settings
■ Comfort settings
The saved settings are automatically used the next time the memorised key is inserted into the ignition switch and
A precondition is that Personalization by driver is activated in the personal settings of the Graphic-Info-Display.
This must be set for each key used.
On vehicles equipped with
Colour-Info-Display, the personalisation is permanently activated.
Vehicle personalisation 3 121.
Keys, doors and windows
Central locking system
21
Unlocks and locks doors, load compartment and fuel filler flap.
A pull on an interior door handle unlocks the respective door. Pulling the handle once more opens the door.
Note
In the event of an accident in which airbags or belt pretensioners are deployed, the vehicle is automatically unlocked.
Note
A short time after unlocking with the remote control the doors are locked automatically if no door has been opened.
22
Unlocking
Keys, doors and windows
The setting can be saved for the key being used. Memorised settings
Locking
Close doors, load compartment and fuel filler flap.
Press button c.
Two settings are selectable:
■ To unlock only the driver's door, load compartment and fuel filler flap, press button c once. To unlock all doors, press button c twice or
■ press button c once to unlock all doors, load compartment and fuel filler flap
The setting can be changed in the menu Settings in the Info-Display.
Vehicle personalisation 3 121.
Press button e.
If the driver's door is not closed properly, the central locking system will not work.
Central locking buttons
Locks or unlocks all doors, the load compartment and fuel filler flap from the passenger compartment.
Press the e button to lock.
Press the c button to unlock.
Fault in radio remote control system
Unlocking
Manually unlock the driver's door by turning the key in the lock. Switch on the ignition and press the central locking button c to unlock all doors, load compartment and fuel filler flap.
By switching on the ignition, the antitheft locking system is deactivated.
Locking
Manually lock the driver's door by turning the key in the lock.
Fault in central locking system
Unlocking
Manually unlock the driver's door by turning the key in the lock. The other doors can be opened by pulling the interior handle twice. The load compartment and fuel filler flap cannot be opened. To deactivate the anti-theft locking system, switch on
Locking
Push inside locking knob of all doors except driver's door. Then close the driver's door and lock it from the outside with the key. The fuel filler flap and tailgate cannot be locked.
Automatic locking
This security feature can be configured to automatically lock all doors, load compartment and fuel filler flap as soon as a certain speed is exceeded.
Additionally it is configurable to unlock the driver's door or all doors after the ignition is switched off and
Keys, doors and windows 23
the ignition key is removed (manual transmission) or the selector lever is moved to P position (automatic transmission).
Settings can be changed in the menu
Settings in the Info-Display. Vehicle
The settings can be saved for the key
Child locks
24 Keys, doors and windows
9 Warning
Use the child locks whenever children are occupying the rear seats.
Using a key or suitable screwdriver, turn the child lock in the rear door to the horizontal position. The door cannot be opened from the inside. For deactivation turn the child lock to the vertical position.
Doors
Load compartment
Tailgate
Opening
Closing
5-door hatchback
After unlocking, push the touchpad switch and open the tailgate.
Sports tourer
After unlocking, push the touchpad switch under the tailgate moulding and open the tailgate.
Use one of the interior handles.
Do not push the touchpad switch below the handle whilst closing as this will unlock the tailgate again.
General hints for operating tailgate
9 Warning
Do not drive with the tailgate open or ajar, e.g. when transporting bulky objects, since toxic exhaust gases, which can not be seen or smelled, could enter the vehicle.
This can cause unconsciousness and even death.
Caution
Before opening the tailgate check overhead obstructions, such as a garage door, to avoid damage to the tailgate. Always check the moving area above and behind the tailgate.
Note
The installation of certain heavy accessories onto the tailgate may affect its ability to remain open.
Vehicle security
Anti-theft locking system
9 Warning
Do not use the system if there are people in the vehicle! The doors cannot be unlocked from the inside.
The system deadlocks all the doors.
All doors must be closed otherwise the system cannot be activated.
If the ignition was on, the driver's door must be opened and closed once so that the vehicle can be secured.
Unlocking the vehicle disables the mechanical anti-theft locking system.
This is not possible with the central locking button.
Keys, doors and windows
Activating
25
Press e on the radio remote control twice within 15 seconds.
Anti-theft alarm system
The anti-theft alarm system is combined with the central locking system.
It monitors:
■ Doors, tailgate, bonnet
■ Passenger compartment including adjoining load compartment
■ Vehicle inclination, e.g. if it is raised
■ Ignition
26 Keys, doors and windows
Activation
■ Self-activated 30 seconds after locking the vehicle (initialisation of the system)
■ Directly by pressing e on the radio remote control once more after locking
Note
Changes to the vehicle interior such as the use of seat covers, and open windows or sunroof, could impair the function of passenger compartment monitoring.
Activation without monitoring of passenger compartment and vehicle inclination
1. Close tailgate, bonnet, windows and sunroof.
2. Press button o. LED in the button o illuminates for a maximum of 10 minutes.
3. Close doors.
4. Activate the anti-theft alarm system.
Status message is displayed in the
Driver Information Centre.
Status LED
Switch off the monitoring of passenger compartment and vehicle inclination when animals are being left in the vehicle, because of high volume ultrasonic signals or movements triggering the alarm. Also switch off when the vehicle is on a ferry or train.
Status LED is integrated in the sensor on top of the instrument panel.
Status during the first 30 seconds of anti-theft alarm system activation:
LED illuminates
LED flashes quickly
= test, arming delay.
= doors, tailgate or bonnet not completely closed, or system fault.
Status after system is armed:
LED flashes slowly
= system is armed.
Seek the assistance of a workshop in the event of faults.
Deactivation
Unlocking the vehicle deactivates the anti-theft alarm system.
Alarm
When triggered, the alarm sounds via a separate battery-backed power sounder, and the hazard warning lights flash simultaneously. The number and duration of alarm signals are stipulated by legislation.
The alarm can be silenced by pressing any button on the radio remote control or by switching on the ignition.
The anti-theft alarm system can be deactivated only by pressing button c or by switching on the ignition.
A triggered alarm, which has not been interrupted by the driver, will be indicated by the hazard warning lights. They will flash quickly three times when the vehicle is unlocked next time with the radio remote control. Additionally a warning message or a warning code is displayed in the Driver Information
Centre after switching on the ignition.
If the vehicle's battery is to be disconnected (e.g. for maintenance work), the alarm siren must be deactivated as follows: switch the ignition on then off, then disconnect the vehicle's battery within
15 seconds.
Keys, doors and windows
Immobiliser
27
The system is part of the ignition switch and checks whether the vehicle is allowed to be started with the key being used.
The immobiliser is activated automatically after the key has been removed from the ignition switch.
If the control indicator d flashes when the ignition is on, there is a fault in the system; the engine cannot be started.
Switch off the ignition and repeat the start attempt.
If the control indicator continues flashing, attempt to start the engine using the spare key and seek the assistance of a workshop.
Note
The immobiliser does not lock the doors. You should always lock the vehicle after leaving it and switch on
the anti-theft alarm system 3 21,
28 Keys, doors and windows
Exterior mirrors
Convex shape
The convex exterior mirror contains an aspherical area and reduces blind spots. The shape of the mirror makes objects appear smaller, which will affect the ability to estimate distances.
Electric adjustment
In position 0 no mirror is selected.
Folding
Electric folding
For pedestrian safety, the exterior mirrors will swing out of their normal mounting position if they are struck with sufficient force. Reposition the mirror by applying slight pressure to the mirror housing.
Turn control to 0, then push the control down. Both exterior mirrors will fold.
Push the control down again - both exterior mirrors return to their original position.
If an electrically folded mirror is manually extended, pressing down the control will only electrically extend the other mirror.
Select the relevant exterior mirror by turning the control to left (L) or right
(R). Then swivel the control to adjust the mirror.
Heated
Interior mirrors
Manual anti-dazzle
Keys, doors and windows
Automatic anti-dazzle
29
Operated by pressing the Ü button.
Heating works with the engine running and is switched off automatically after a short time.
To reduce dazzle, adjust the lever on the underside of the mirror housing.
Dazzle from following vehicles at night is automatically reduced.
30 Keys, doors and windows
Windows
Windscreen
Heat-reflecting windscreen
The heat-reflecting windscreen has a coating which reflects solar radiation. Also data signals, e.g. from toll stations, might be reflected.
The marked areas of the windscreen behind the interior mirror are not covered with the coating. Devices for electronic data recording and fee payment must be attached in these areas. Otherwise data recording malfunctions may occur.
Manual windows
The door windows can be opened or closed with the window winders.
Power windows
9 Warning
Take care when operating the power windows. Risk of injury, particularly to children.
If there are children on the rear seats, switch on the child safety system for the power windows.
Keep a close watch on the windows when closing them.
Ensure that nothing becomes trapped in them as they move.
Switch on ignition to operate power
windows. Retained power off 3 146.
Operate the switch for the respective window by pushing to open or pulling to close.
Pushing or pulling gently to the first detent: window moves up or down as long as the switch is operated.
Pushing or pulling firmly to the second detent and then releasing: window moves up or down automatically with safety function enabled. To stop movement, operate the switch once more in the same direction.
Safety function
If the window glass encounters resistance above the middle of the window during automatic closing, it is immediately stopped and opened again.
Override safety function
In the event of closing difficulties due to frost or the like, switch on the ignition, then pull the switch to the first detent and hold. The window moves up without safety function enabled.
To stop movement, release the switch.
Child safety system for rear windows
Press switch z to deactivate rear door power windows, the LED illuminates. To activate, press z again.
Operating windows from outside
The windows can be operated remotely from outside the vehicle.
Keys, doors and windows 31
Press and hold c button to open windows.
Press and hold e button to close windows.
Release button to stop window movement.
If the windows are fully opened or closed, the hazard warning lights will flash two times.
Overload
If the windows are repeatedly operated within short intervals, the window operation is disabled for some time.
32 Keys, doors and windows
Initialising the power windows
If the windows cannot be closed automatically (e.g. after disconnecting the vehicle battery), a warning message or a warning code is displayed in the Driver Information
Centre.
Activate the window electronics as follows:
1. Close doors.
2. Switch on ignition.
3. Pull switch until the window is closed and keep pulling for additional 2 seconds.
4. Repeat for each window.
Heated rear window
Operated by pressing the Ü button.
Heating works with the engine running and is switched off automatically after a short time.
Depending on the engine type, the heated rear window comes on automatically when the diesel particle filter is being cleaned.
Sun visors
The sun visors can be folded down or swivelled to the side to prevent dazzling.
If the sun visors have integral mirrors, the mirror covers should be closed when driving.
A ticket holder is located on the backside of the sun visor.
Roof
Sunroof
9 Warning
Take care when operating the sunroof. Risk of injury, particularly to children.
Keep a close watch on the movable parts when operating them. Ensure that nothing becomes trapped in them as they move.
Switch on ignition to operate the sunroof.
Open or close
Press p or r gently to the first detent: sunroof is opened or closed with safety function enabled as long as the switch is operated.
Press p or r firmly to the second detent and then release: the sunroof is opened or closed automatically with safety function enabled. To stop movement, operate the switch once more.
Keys, doors and windows 33
Raise or close
Press q or r: sunroof is raised or closed automatically with safety function enabled.
If the sunroof is raised, it can be opened in one step by pressing p.
Sunblind
The sunblind is manually operated.
Close or open the sunblind by sliding.
When the sunroof is open, the sunblind is always open.
General hints
Safety function
If the sunroof encounters resistance during automatic closing, it is immediately stopped and opened again.
Override safety function
In the event of closing difficulties due to frost or the like, hold the switch r pressed to the second detent.
The sunroof closes without safety function enabled. To stop movement, release the switch.
34 Keys, doors and windows
Closing sunroof from outside
The sunroof can be closed remotely from outside the vehicle.
Press and hold e button to close the sunroof.
Release the button to stop the movement.
Initialising after a power failure
After a power failure, it may only be possible to operate the sunroof to a limited extent. Have the system initialised by your workshop.
Seats, restraints
Head restraints ............................ 35
Front seats ................................... 37
Rear seats ................................... 40
Seat belts ..................................... 41
Airbag system .............................. 44
Child restraints ............................. 48
Head restraints
Position
9 Warning
Only drive with the head restraint set to the proper position.
Seats, restraints
Adjustment
Head restraints on front seats
35
Height adjustment
Press the button, adjust height and engage.
The upper edge of the head restraint should be at upper head level. If this is not possible for extremely tall people, set to highest position, and set to lowest position for small people.
36 Seats, restraints
Horizontal adjustment Head restraints on rear seats forwards. Thus the head is supported so that the risk of whiplash injury is reduced.
Note
Approved accessories may only be attached if the seat is not in use.
To adjust horizontally, pull the head restraint forwards. It engages in several positions.
To return to its rearmost position, pull fully forwards and release.
Height adjustment
Pull the head restraint upwards or press the catch to release and push the head restraint downwards.
Removal
Press both catches, pull the head restraint upwards and remove.
Active head restraints
In the event of a rear-end impact, the front parts of the active head restraints are moved slightly
Front seats
Seat position
9 Warning
Only drive with the seat correctly adjusted.
■ Sit with buttocks as far back against the backrest as possible. Adjust the distance between the seat and the pedals so that legs are slightly angled when pressing the pedals.
Slide the front passenger seat as far back as possible.
■ Sit with shoulders as far back against the backrest as possible.
Set the backrest rake so that it is possible to easily reach the steering wheel with arms slightly bent. Maintain contact between shoulders and the backrest when turning the steering wheel. Do not angle the backrest too far back. We recommend a maximum rake of approx. 25°.
■ Adjust the steering wheel 3 91.
■ Set seat height high enough to have a clear field of vision on all sides and of all display instruments.
There should be at least one hand of clearance between head and the roof frame. Your thighs should rest lightly on the seat without pressing into it.
■ Adjust the head restraint 3 35.
■ Adjust the height of the seat belt
■ Adjust the thigh support so that there is a space approx. two fingers wide between the edge of the seat and the hollow of the knee.
Seats, restraints 37
■ Adjust the lumbar support so that it supports the natural shape of the spine.
Seat adjustment
9 Danger
Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment.
9 Warning
Never adjust seats while driving as they could move uncontrollably.
9 Warning
Never store any subjects under the seats.
Drive only with engaged seats and backrests.
38 Seats, restraints
Seat positioning Seat backrests Seat height
Pull handle, slide seat, release handle.
Pull lever, adjust inclination and release lever. Allow the backrest to engage audibly.
Lever pumping motion up = seat higher down = seat lower
Seat inclination Lumbar support
Seats, restraints
Adjustable thigh support
39
Lever pumping motion up = front end higher down = front end lower
Adjust lumbar support using the fourway switch to suit personal requirements.
Moving support up and down: push switch up or down.
Increasing and decreasing support: push switch forwards or backwards.
Pull the lever and slide the thigh support.
40
Armrest
Seats, restraints
Heating
Rear seats
Armrest
The armrest can be slid forwards by
10 cm. Under the armrest there is a storage compartment.
Adjust heating to the desired setting by pressing the ß button for the respective seat one or more times.
The control indicator in the button indicates the setting.
Prolonged use of the highest setting for people with sensitive skin is not recommended.
Seat heating is operational when engine is running and during an
Autostop.
Fold armrest down. The armrest contains cupholders and a storage box.
Seat belts
The seat belts are locked during heavy acceleration or deceleration of the vehicle holding the occupants in the sitting position. Therefore the risk of injury is considerably reduced.
9 Warning
Fasten seat belt before each trip.
In the event of an accident, people not wearing seat belts endanger their fellow occupants and themselves.
Seat belts are designed to be used by only one person at a time. They are not suitable for people smaller than
150 cm. Child restraint system
Periodically check all parts of the belt system for damage, pollution and proper functionality.
Have damaged components replaced. After an accident, have the belts and triggered belt pretensioners replaced by a workshop.
Note
Make sure that the belts are not damaged by shoes or sharp-edged objects or trapped. Prevent dirt from getting into the belt retractors.
Seat belt reminder
Front seats are equipped with a seat belt reminder, indicated for driver seat as control indicator X in the tachometer and for passenger seat in
Seats, restraints 41
Belt force limiters
On the front seats, stress on the body is reduced by the gradual release of the belt during a collision.
Belt pretensioners
In the event of a head-on or rear-end collision of a certain severity, the front seat belts are tightened.
9 Warning
Incorrect handling (e.g. removal or fitting of belts) can trigger the belt pretensioners.
Deployment of the belt pretensioners is indicated by continuous illumination
Triggered belt pretensioners must be replaced by a workshop. Belt pretensioners can only be triggered once.
42 Seats, restraints
Note
Do not affix or install accessories or other objects that may interfere with the operation of the belt pretensioners. Do not make any modifications to belt pretensioner components as this will invalidate the vehicle type approval.
Three-point seat belt
Fastening
buckle. Tighten the lap belt regularly whilst driving by pulling the shoulder belt.
Height adjustment
1. Pull belt out slightly.
2. Press button.
3. Adjust height and engage.
Withdraw the belt from the retractor, guide it untwisted across the body and insert the latch plate into the
Loose or bulky clothing prevents the belt from fitting snugly. Do not place objects such as handbags or mobile phones between the belt and your body.
9 Warning
The belt must not rest against hard or fragile objects in the pockets of your clothing.
Removing
Seats, restraints
Using the seat belt while pregnant
43
Adjust the height so that the belt lies across the shoulder. It must not lie across the throat or upper arm.
Do not adjust while driving.
To release belt, press red button on belt buckle.
Seat belts on the rear seats
The seat belt for the rear centre seat can only be withdrawn from the retractor if the backrest is engaged in upright position.
9 Warning
The lap belt must be positioned as low as possible across the pelvis to prevent pressure on the abdomen.
44 Seats, restraints
Airbag system
The airbag system consists of a number of individual systems depending on the scope of equipment.
When triggered the airbags inflate within milliseconds. They also deflate so quickly that it is often unnoticeable during the collision.
9 Warning
If handled improperly the airbag systems can be triggered in an explosive manner.
Note
The airbag systems and belt pretensioner control electronics are located in the centre console area.
Do not put any magnetic objects in this area.
Do not stick anything on the airbag covers and do not cover them with other materials.
Each airbag is triggered only once.
Have deployed airbags replaced by a workshop. Furthermore, it might be necessary to have the steering wheel, the instrument panel, parts of the panelling, the door seals, handles and the seats replaced.
Do not make any modifications to the airbag system as this will invalidate the vehicle type approval.
When the airbags inflate escaping hot gases may cause burns.
Control indicator v for airbag systems
Front airbag system
The front airbag system consists of one airbag in the steering wheel and one in the instrument panel on the front passenger side. These can be identified by the word AIRBAG.
There are also warning labels on both sides of the sunblind on the front passenger side.
The front airbag system is triggered in the event of a front-end impact of a certain severity. The ignition must be switched on.
Seats, restraints 45
Fit the seat belt correctly and engage securely. Only then the airbag is able to protect.
Side airbag system
The inflated airbags cushion the impact, thereby reducing the risk of injury to the upper body and head of the front seat occupants considerably.
9 Warning
Optimum protection is only provided when the seat is in the
Keep the area in which the airbag inflates clear of obstructions.
The side airbag system consists of an airbag in each front seat backrest.
This can be identified by the word
AIRBAG.
The side airbag system is triggered in the event of a side impact of a certain severity. The ignition must be switched on.
The inflated airbags cushion the impact, thereby reducing the risk of injury to the upper body and pelvis in the event of a side-on collision considerably.
9 Warning
Keep the area in which the airbag inflates clear of obstructions.
Note
Only use protective seat covers that have been approved for the vehicle.
Be careful not to cover the airbags.
46 Seats, restraints
Curtain airbag system
The curtain airbag system consists of an airbag in the roof frame on each side. This can be identified by the word AIRBAG on the roof pillars.
The curtain airbag system is triggered in the event of a side-on impact of a certain severity. The ignition must be switched on.
9 Warning
Keep the area in which the airbag inflates clear of obstructions.
The hooks on the handles in the roof frame are only suitable for hanging up light articles of clothing, without coat hangers. Do not keep any items in these clothes.
Airbag deactivation
The front passenger airbag system has to be deactivated if a child restraint system is to be fitted on this seat. The side airbag and curtain airbag systems, the belt pretensioners and all driver airbag systems will remain active.
The front passenger airbag system can be deactivated via a keyoperated switch on the right side of the instrument panel.
The inflated airbags cushion the impact, thereby reducing the risk of injury to the head in the event of a side-on impact considerably.
Use the ignition key to choose the position:
*OFF = front passenger airbag is deactivated and will not inflate in the event of a collision. Control indicator *OFF illuminates continuously in the centre console. A child restraint system can be installed in accordance with the chart Child restraint installation
person is allowed to occupy the front passenger seat.
V ON = front passenger airbag is active. A child restraint system must not be installed.
9 Danger
Risk of fatal injury for a child using a child restraint system on a seat with activated front passenger airbag.
Risk of fatal injury for an adult person on a seat with deactivated front passenger airbag.
If the control indicator V illuminates for approx. 60 seconds after the ignition is switched on, the front passenger airbag system will inflate in the event of a collision.
If both control indicators are illuminated at the same time, there is a system failure. The status of the system is not discernible, therefore no person is allowed to occupy the front passenger seat. Contact a workshop immediately.
Seats, restraints 47
Change status only when the vehicle is stopped with the ignition off.
Status remains until the next change.
Control indicator for airbag
48 Seats, restraints
Child restraints
Child restraint systems
We recommend the Vauxhall child restraint system which is tailored specifically to the vehicle.
When a child restraint system is being used, pay attention to the following usage and installation instructions and also those supplied with the child restraint system.
Always comply with local or national regulations. In some countries, the use of child restraint systems is forbidden on certain seats.
9 Warning
When using a child restraint system on the front passenger seat, the airbag systems for the front passenger seat must be deactivated; if not, the triggering of the airbags poses a risk of fatal injury to the child.
This is especially the case if rearfacing child restraint systems are used on the front passenger seat.
Selecting the right system
The rear seats are the most convenient location to fasten a child restraint system.
Children should travel facing rearwards in the vehicle as long as possible. This makes sure that the child's backbone, which is still very weak, is under less strain in the event of an accident.
Children under the age of 12 years that are smaller than 150 cm are only allowed to travel in a restraint system that is suitable for the child. Suitable are restraint systems that comply with
ECE 44-03 or ECE 44-04. Since a proper position of the belt is rarely possible with a child that is smaller than 150 cm, we strongly advise the use of an appropriate child restraint system, even though this might, due to the age of the child, no longer be legally binding.
Ensure that the child restraint system to be installed is compatible with the vehicle type.
Ensure that the mounting location of the child restraint system within the vehicle is correct.
Allow children to enter and exit the vehicle only on the side facing away from the traffic.
When the child restraint system is not in use, secure the seat with a seat belt or remove it from the vehicle.
Note
Do not stick anything on the child restraint systems and do not cover them with any other materials.
A child restraint system which has been subjected to stress in an accident must be replaced.
Seats, restraints 49
Child restraint installation locations
Permissible options for fitting a child restraint system
Weight and age class
On front passenger seat activated airbag deactivated airbag
X U 1 Group 0: up to 10 kg or approx. 10 months
Group 0+: up to 13 kg or approx. 2 years
Group I: 9 to 18 kg or approx. 8 months to 4 years
Group II: 15 to 25 kg or approx. 3 to 7 years
Group III: 22 to 36 kg or approx. 6 to 12 years
X
X
X
X
U 1
U 1
X
X
On rear outboard seats On rear centre seat
U 2 U
U 2
U 2
U
U
U
U
U
U
1 = Only if front passenger seat airbag system is deactivated. If the child restraint system is being secured using a threepoint seat belt, move seat height adjustment to uppermost position and ensure that vehicle safety belt runs forwards from the upper anchorage point. Adjust seat backrest inclination as far as necessary to a vertical position to ensure that the belt is tight on the buckle side.
2 = Seat available with ISOFIX and Top-Tether mounting brackets.
U = Universal suitability in conjunction with three-point seat belt.
X = No child restraint system permitted in this weight class.
50 Seats, restraints
Permissible options for fitting an ISOFIX child restraint system
Weight class Size class Fixture On front passenger seat On rear outboard seats On rear centre seat
Group 0: up to 10 kg E
Group 0+: up to 13 kg E
Group I: 9 to 18 kg
D
C
D
C
B
B1
A
ISO/R1 X
ISO/R1 X
ISO/R2 X
ISO/R3 X
ISO/R2 X
ISO/R3 X
ISO/F2 X
ISO/F2X X
ISO/F3 X
IL
IL
IL
IL
IL
IL
IL, IUF
IL, IUF
IL, IUF
X
X
X
X
X
X
X
X
X
IL = Suitable for particular ISOFIX restraint systems of the 'specific-vehicle', 'restricted' or 'semi-universal' categories.
The ISOFIX restraint system must be approved for the specific vehicle type.
IUF = Suitable for ISOFIX forward-facing child restraint systems of universal category approved for use in this weight class.
X = No ISOFIX child restraint system approved in this weight class.
Seats, restraints
ISOFIX size class and seat device
A – ISO/F3
B – ISO/F2
= Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg.
= Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg.
B1 – ISO/F2X = Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg.
C – ISO/R3 = Rear-facing child restraint system for children of maximum size in the weight class up to 13 kg.
D – ISO/R2 = Rear-facing child restraint system for smaller children in the weight class up to 13 kg.
E – ISO/R1 = Rear-facing child restraint system for young children in the weight class up to 13 kg.
51
52 Seats, restraints
ISOFIX child restraint systems
Top-tether fastening eyes
Top-Tether fastening eyes are marked with the symbol : for a child seat.
Fasten vehicle-approved ISOFIX child restraint systems to the ISOFIX mounting brackets. Specific vehicle
ISOFIX child restraint system positions are marked in the table by
IL.
ISOFIX mounting brackets are indicated by a label on the backrest.
In addition to the ISOFIX mounting fasten the Top-Tether strap to the
Top-Tether fastening eyes. The strap must run between the two guide rods of the head restraint.
ISOFIX child restraint systems of universal category positions are marked in the table by IUF.
Storage
Storage compartments ................ 53
Load compartment ....................... 74
Roof rack system ......................... 88
Loading information ..................... 89
Storage compartments
Glovebox
Cupholders
Storage 53
The glovebox features a pen holder, a credit card holder and a coin holder.
The glovebox should be closed whilst driving.
Cupholders are located in the centre console.
54 Storage
Depending on the version, cupholders are located under a cover in the centre console. Slide cover backwards. Bottles can be stowed after folding up the intermediate shelf
Front storage Sunglasses storage
Additional cupholders are located in the rear armrest. Fold down the armrest.
A storage compartment is located next to the steering wheel.
Fold down and open.
Do not use for storing heavy objects.
Underseat storage Armrest storage
Storage under the front armrest
Storage
Storage in the rear armrest
55
Press button in the recess and pull out drawer. Maximum load: 3 kg. To close, push in and engage.
Depending on the version, the tyre repair kit is stowed in the drawer.
Press button to fold up the armrest.
The armrest must be in rearmost position.
Fold down armrest and open cover.
Close cover before folding the armrest up.
56 Storage
Centre console storage
Front console
A further storage compartment is located under the intermediate shelf.
Fold up the intermediate shelf and fix it in the vertical position. The frame of the cupholder can be reintegrated to stow bottles.
Rear console
The storage container can be used to store small items.
Depending on the version, a storage compartment is located under a cover.
Slide cover backwards.
Press button to remove the frame of the cupholder. The frame can be stowed in the glovebox.
Pull out the drawer.
Caution
Do not use for ashes or for other glowing items.
Storage 57
Rear carrier system
Rear carrier system for two bicycles
The rear carrier system (Flex-Fix system) allows bicycles to be attached to a pull-out carrier integrated into the vehicle floor. The transportation of other objects is not permitted.
The maximum load of the rear carrier system is 40 kg. The maximum load per bicycle is 20 kg.
If not in use, the carrier system must be slid back into the vehicle floor.
There must not be any objects on the bicycles that could become loose during transportation.
Caution
Do not attach bicycles with carbon pedal cranks to bicycle carriers.
The bicycles might get damaged.
Extending
Open the tailgate.
9 Warning
No-one should be in the extension zone of the rear carrier system, risk of injury.
Pull release lever up. The system disengages and travels quickly out of the bumper.
58 Storage
Completely pull out the rear carrier system until you hear it engage.
Ensure that it is not possible to push in the rear carrier system without pulling the release lever again
9 Warning
It is only permissible to fit objects to the rear carrier system if the system has been correctly engaged. If the rear carrier system will not engage correctly, do not fit objects to the system and slide the system back. Seek the assistance of a workshop.
Install the tail lamps
First remove the rear (1), then the front (2) tail lamp from the recesses.
Open out the lamp support on the back of the tail lamp completely.
Push the clamping lever down and push the lamp support into the retainer until it engages.
Perform this procedure for both tail lamps.
Storage 59
Lock the rear carrier system
Check the cable and lamp position to make sure these are correctly installed and are securely located.
Swivel the right clamping lever (1) first, followed by the left clamping lever (2), until a resistance is noticeable.
The rear carrier system is locked when the clamping levers are swivelled by approx. 50°. Otherwise safe functionality is not guaranteed.
Note
Close the tailgate.
60 Storage
Unfold pedal crank recesses Adapting the rear carrier system to a bicycle
Fold one or both pedal crank recesses upwards until the diagonal support engages.
Remove the pedal crank mounts from the pedal crank recesses.
Press the release lever and withdraw the wheel recesses.
Storage 61
Push the release lever on the strap retainer and remove the strap retainer.
Prepare the bicycle for attachment
The rear bicycle must have its front wheel facing right.
Attaching a bicycle to the rear carrier system
Note
The maximum width for the pedal crank is 38.3 mm and the maximum depth is 14.4 mm.
Rotate the left pedal (without a chain cog) vertically downwards. The pedal on the left pedal crank must be horizontal.
The front bicycle must have its front wheel facing left.
With the rotary lever on the pedal crank recess, roughly adapt the adjustable pedal crank unit to the protrusion of the pedal crank.
If the bicycle has straight pedal cranks, unscrew the pedal crank unit completely (position 5).
If the bicycle has curved pedal cranks, screw in the pedal crank unit all the way (position 1).
62 Storage
Put on the bicycle. The pedal crank here must be placed in the pedal crank recess opening as shown in the illustration.
Caution
Make sure that the pedal does not touch the surface of the rear end carrier. Otherwise the crankset might be damaged during the transport.
Attach the pedal crank by rotating the attachment screw on the pedal crank mount.
Place the wheel recesses such that the bicycle is more or less horizontal.
Here, the distance between the pedals and the tailgate should be at least 5 cm.
Both bicycle tyres must be in the wheel recesses.
Insert pedal crank mount into outer rail of each pedal crank recess from above and slide downwards until at least underneath the notching.
Align the bicycle in the longitudinal direction of the vehicle: Slightly loosen the pedal mount.
Place the bicycle upright using the rotary lever on the pedal crank recess.
If the two bicycles obstruct one another, the relative positions of the bicycles can be adapted by adjusting the wheel recesses and the rotary lever on the pedal crank recess until the bicycles no longer touch one another. Make sure there is sufficient clearance from the vehicle.
Check the bicycle to make sure it is secure.
Caution
Ensure gap between bicycle and vehicle is at least 5 cm.
The settings for the wheel recesses and on the rotary lever on the pedal crank recess should be noted and saved for each bicycle. Correct presetting will facilitate refitting of the bicycle.
Storage 63
It is recommended to attach a warning sign at the rearmost bicycle to increase visibility.
Removing a bicycle from the rear carrier system
Tighten the attachment screw for the pedal bearing mount to its maximum point by hand.
Secure both bicycle wheels to the wheel recesses using the strap retainers.
Undo strap retainers on both bicycle tyres.
Hold on to the bicycle, loosen the attachment screw for the pedal bearing mount, then lift the pedal bearing mount to remove it.
64 Storage
Retracting the rear carrier system Insert the strap retainer and pull tightly downwards as far as possible.
Push the pedal crank mounts into the pedal crank recess like shown in the graphic.
Press release lever and slide in wheel recesses all the way as far as they will go.
Disengage the locking lever on the diagonal support and fold both pedal crank recesses down.
9 Warning
Risk of pinching.
Storage 65
Push the clamping lever down and pull both lamp supports out of the recesses.
Swivel first the left clamping lever (1), followed by the right clamping lever
(2), until they stop.
Fold in the lamp supports on the backs of the tail lamps.
First place the front (1) tail lamp, then the rear (2) tail lamp in the recesses and push down as far as possible.
Push cables all the way into all guides in order to prevent damage.
Open the tailgate.
Pull the release lever up and push the system into the bumper until it engages.
Release lever must return to original position.
9 Warning
If the system cannot be correctly engaged, please seek the assistance of a workshop.
66 Storage
Rear carrier system for four bicycles
The rear carrier system (Flex-Fix system) allows two bicycles to be attached to a pull-out carrier integrated into the vehicle floor. It is possible to attach two further bicycles on an adapter. The transportation of other objects is not permitted.
The maximum load of the rear carrier system is 80 kg with attached adapter and 60 kg without attached adapter.
The maximum load per bicycle on the pull-out carrier is 30 kg. This allows the attachment of electricallypowered bicycles to the pull-out carrier. The maximum load per bicycle on the adapter is 20 kg.
If not in use, the carrier system must be slid back into the vehicle floor.
There must not be any objects on the bicycles that could become loose during transportation.
Caution
If the rear carrier system is extended and the vehicle is fully loaded, the chassis clearance will be reduced.
Drive carefully whenever the road has a strong inclination or when driving over a ramp, bump, etc.
Caution
Consult your bicycle dealer before attaching bicycles with carbon frames. The bicycles might get damaged.
Extending
Open the tailgate.
9 Warning
No-one should be in the extension zone of the rear carrier system, risk of injury.
Pull release lever up. The system disengages and travels quickly out of the bumper.
Unfold number plate holder
Storage
Fold out tail lamps
67
Completely pull out the rear carrier system until you hear it engage.
Ensure that it is not possible to push in the rear carrier system without pulling the release lever again.
9 Warning
It is only permissible to fit objects to the rear carrier system if the system has been correctly engaged. If the rear carrier system will not engage correctly, do not fit objects to the system and slide the system back. Seek the assistance of a workshop.
Lift the number plate holder and fold it backwards.
Fold out both tail lamps.
Lock the rear carrier system
68 Storage
Swivel both clamping levers sidewards as far as they will go.
Otherwise safe functionality is not guaranteed.
Fold out wheel recesses
Assembling the bicycle rack
Lift the rack at the rear (1) and pull it backwards.
Fold up the rack (2).
Push down the rack (1) and swivel handle (2) backwards to engage.
Attaching the first bicycle
Fold out both wheel recesses.
Storage 69
1. Rotate the pedals into position as shown in the illustration and put the bicycle on the foremost wheel recess.
Make sure that the bicycle stands centrally on the wheel recesses.
2. Attach the short mounting bracket to the bicycle frame. Turn the knob clockwise to fasten.
3. Secure both bicycle wheels to the wheel recesses using the strap retainers.
4. Check the bicycle to make sure it is secure.
Caution
Ensure gap between bicycle and vehicle is at least 5 cm.
Attaching the adapter
When carrying more than two bicycles, the adapter has to be fixed before the second bicycle is attached.
1. Apply the adapter to the rear carrier system as shown in the illustration.
70 Storage
2. Turn the lever (1) forwards and hold, then lower the adapter (2) at the rear.
3. Release lever and check if the adapter is engaged securely.
1. Before putting on the bicycle, always unfold the wheel recesses for the next bicycle if necessary.
2. Always rotate the pedals into an appropriate position before putting on the bicycle.
mounting brackets should be fixed in parallel.
Use the long mounting bracket to attach the second bicycle to the rack.
Use the longer accessory mounting bracket to attach the third bicycle to the rack.
4. Guide the strap attached to the adapter underneath the lever for folding back the rear carrier system. Fasten the strap.
Attaching further bicycles
The attachment of further bicycles is similar to the attachment of the first bicycle. Additionally some steps must be considered:
3. Position the bicycles on the rear carrier system alternately aligned to the left and to the right.
4. Align the bicycles to the one attached before. The wheel hubs of the bicycles must not touch each other.
5. Attach the bicycles with mounting brackets and strap retainers as described for the first bicycle. The
Use the short accessory mounting bracket to attach the fourth bicycle. The bracket has to be fixed between the frames of the third and fourth bicycle.
6. Additionally secure both bicycle wheels of the fourth bicycle to the wheel recesses using the tensioning straps.
It is recommended to attach a warning sign at the rearmost bicycle to increase visibility.
Fold the rear carrier system backwards
The rear carrier system can be folded backwards to get access to the load compartment.
■ Without attached adapter:
Storage
■ With attached adapter:
9 Warning
Take care when disengaging the rear carrier system as it will tilt backwards. Risk of injury.
71
Push the lever (1) to disengage and hold.
Pull the rack (2) backwards to fold the rear carrier system.
Hold frame (1) of rearmost bicycle with one hand and pull the loop (2) to disengage.
Hold rearmost bicycle with both hands and fold the rear carrier system backwards.
To increase visibility, the tail lights of the vehicle are activated when the rear carrier system is folded back.
72 Storage
9 Warning
When folding the rear carrier system forwards again, take care that the system is engaged securely.
Removing bicycles
Undo strap retainers on both bicycle tyres.
Turn knob anti-clockwise and remove mounting brackets.
Detaching adapter
Detach the adapter before removing the last bicycle left on the rear carrier system.
1. Fold in wheel recesses.
2. Unbutton the strap.
3. Turn the lever (1) forwards and hold.
4. Lift the adapter (2) at the rear and remove.
Disassembling the bicycle rack
Arrange mounting brackets as shown in the illustration.
Swivel handle (1) forwards to disengage and lift the rack (2).
Fold the rack backwards, then push forwards until it stops (1).
Press the rack down at the rear (2).
Fold in wheel recesses
Fold in both wheel recesses.
Stow the strap retainers accurately.
Unlock the rear carrier system
Storage 73
Swivel both clamping levers inwards as far as they will go.
Fold in tail lamps
Swivel in both tail lamps.
Fold in number plate holder
Lift the number plate holder and fold it forwards.
Retracting the rear carrier system
Caution
Take care that all foldable parts as wheel recesses or mounting brackets are stowed accurately.
Otherwise the rear carrier system might get damaged when trying to retract it.
74 Storage
Pull release lever up and push the rear carrier system in the bumper until you hear it engage.
9 Warning
If the system cannot be correctly engaged, please seek the assistance of a workshop.
Load compartment
The rear seat backrest is divided into two parts. Both parts can be folded down.
Load compartment extension,
5-door hatchback
Remove the load compartment cover if necessary.
Press and hold the catch, then push the head restraints down.
Fold up the rear armrest.
Guide the seat belts through side supports to protect them against damage. When folding the backrests, pull the seat belts along with them.
Pull the release lever on one or both sides and fold down the backrests onto the seat cushion.
If the vehicle is to be loaded via a rear door, take the seat belt out of the seat backrest guide and put it behind the retainer as shown in the illustration.
To fold up, raise the backrests and guide them into an upright position until they engage audibly.
Ensure that the seat belts of the outboard seats are placed in the corresponding belt guides.
9 Warning
When folding up, ensure that backrests are securely locked in position before driving. Failure to do so may result in personal injury or damage to load or vehicle in the event of heavy braking or collision.
Storage 75
Load compartment extension,
Sports tourer
Folding down rear backrests
Remove the load compartment cover if necessary.
Press and hold the catch, then push the head restraints down.
Fold up the rear armrest.
The backrests are properly engaged when the red marks on both sides near the release lever are no longer visible.
The seat belt of the centre seat could be blocked when the backrest is folded up too quickly. To unlock the retractor, push in the seat belt or pull it out by approx. 20 mm and then let go.
Guide the seat belts through side supports to protect them against damage. When folding the backrests, pull the seat belts along with them.
76 Storage
Pull the release lever on one or both sides and fold down the backrests onto the seat cushion.
On vehicles with electric seat folding, the rear seats can also be folded from the load compartment.
9 Warning
Take care when operating the electric foldable rear seats. The seat backrest is folded with considerable power. Risk of injury, particularly to children.
Ensure that nothing is attached to the rear seats or located on the seat cushion.
To fold up, raise the backrests and guide them into an upright position until they engage audibly.
Ensure that the seat belts of the outboard seats are placed in the corresponding belt guides.
Pull switch on left or right sidewall of the load compartment to fold the corresponding part of the rear seat.
If the vehicle is to be loaded via a rear door, take the seat belt out of the seat backrest guide and put it behind the retainer as shown in the illustration.
The backrests are properly engaged when the red marks on both sides near the release lever are no longer visible.
9 Warning
Only drive the vehicle if the backrests are securely locked into position. Otherwise there is a risk of personal injury or damage to the load or vehicle in the event of heavy braking or a collision.
Raise the seat cushion and fold the backrest
Storage
Remove the seat cushion
77
The seat belt of the centre seat could be blocked when the backrest is folded up too quickly. To unlock the retractor, push in the seat belt or pull it out by approx. 20 mm and then let go.
Pull the strap on one or both seat cushions and lift the rear of the cushion forwards.
Push rear head restraints downward.
Pull the release lever on one or both sides of the backrests and fold down onto the seat cushion to get a flat load bay.
Push both levers forward and remove seat cushion to extend the loading area.
78 Storage
To attach, apply seat cushion as shown in the illustration and engage both levers.
Open the pass-through in the rear centre backrest
Fold down the rear armrest.
Pull the grip and open the cover.
Suitable for loading long, narrow objects.
Ensure that the cover engages after folding up.
The closed cover can be secured from the side of the load compartment. Turn the knob 90°: knob horizontal knob vertical
= cover secured from the side of the passenger compartment
= cover not secured
Load compartment cover
Do not place any objects on the cover.
Storage 79
5-door hatchback
Removing
Unhook retaining straps from tailgate.
Lift cover at the rear and push it upwards at the front.
Remove the cover.
If the height adjustable cover is mounted in the middle or upper position, the load compartment cover can be stowed below it.
Fitting
Engage cover in side guides and fold downwards. Attach retaining straps to tailgate.
Sports tourer
Closing cover
Pull the cover towards the rear using the handle until it engages in the sideward retainers.
Opening cover
Pull the handle at the end of the cover to the rear and downwards. It rolls up automatically.
80 Storage
Cover in upper position Removing cover
Push the handle at the end of the cover downwards. The rear of the cover is guided upwards automatically.
Open the load compartment cover.
Pull the release lever on the right side up and hold it. Lift the cover first on the right side and remove from retainers.
The removed cover can be stored under the rear floor cover like shown in the graphic.
Rear floor storage cover 3 81.
Installing cover
Insert the left side of the load compartment cover in the recess, pull the release lever up and hold it, insert the right side of the load compartment cover and engage.
Rear floor storage cover
Rear floor cover, 5-door hatchback
Height adjustable cover, 5-door hatchback
Lifting
Storage 81
The rear floor cover can be lifted and hooked in with the loop.
Caution
Only use the hook for hanging up the rear floor cover and the height adjustable cover.
The height adjustable cover can be mounted in three positions:
■ directly above the rear floor cover
(1),
■ in a middle position (2)
■ in an upper position (3).
Caution
Ensure that the front and rear end of the height adjustable cover are attached to the same level.
To lift the cover to a higher level, pull the loop backwards and lift the rear edge of the cover onto the corresponding supports.
82
Lowering
Storage
To lower the cover, pull the strap backwards and push down the front centre of the cover at the same time.
Caution
Do not lower the height adjustable cover to position 1 in vehicles equipped with subwoofer. The subwoofer could be damaged.
Note
■ If mounted in position 2 or 3, the space between the rear floor cover and the height adjustable cover can be used as a stowage compartment.
■ The height adjustable cover can be lifted and hooked in with the strap when it is mounted in position 1 or 2.
■ If mounted in position 2, an almost completely flat load bay is created if the rear seat backrests are folded forwards.
■ The height adjustable cover is able to withstand a load of no more than 100 kg.
■ Opening the side covers (e.g.
when exchanging the rear light bulbs) is only possible with the height adjustable cover mounted in position 1 or 2.
Rear floor cover, Sports tourer
Lift the rear floor cover by pulling the handle. Fold and place the cover behind the rear seats.
The storage compartment below the rear floor cover can be divided by a bar.
Lashing eyes
Storage 83
■ hooks,
■ service box,
■ strap set.
The components are fitted in rails on both side panels using adapters and hooks.
Installation of adapters in the rails
Insert the bar into the recesses at the sidewalls.
Caution
Insert the bar into the rearmost recess when transporting heavy objects in the load compartment.
Otherwise the rear floor cover might be damaged.
The lashing eyes are designed to secure items against slippage, e.g.
using lashing straps or luggage net.
Cargo management system
The FlexOrganizer is a flexible system for dividing up the load compartment.
The system consists of:
■ adapters,
■ mesh pockets,
Fold open the handle plate, insert the adapter into the upper and lower groove of the rail and move to the required position. Turn the handle
84 Storage
plate upwards to lock the adapter. To remove, turn the handle plate down and move out of the rail.
Variable partition net
Net pocket Installation of hooks in the rails
Insert adapters into the required position in the rails. Stick together the halves of the net rods.
To install, push rods together a little and insert into the relevant openings in the adapters.
To remove, press the net rods together and remove from the adapters.
Insert adapters into the required position in the rails. The net pocket can be suspended from the adapters.
Insert the hook in the desired position first in the upper groove of the rail and then press in the lower groove. To remove, first pull out of the upper groove.
Service box Strap set
Storage 85
Install two hooks in the upper rail.
Insert the upper brackets of the box from above into the hooks.
Alternatively install both hooks in the lower rail. Plug in the lower brackets of the box from above into the lower hooks.
Insert the adapters of the strap set in a rail. Make sure that the belt is not twisted.
The strap set has two locks to open.
The belt can be tightened.
Safety net
The safety net is available on the
Sports tourer and can be installed behind the rear seats or, if the rear seat backrests are folded and the seat cushions raised, behind the front seats.
86 Storage
Passengers must not be transported behind the safety net.
Installation
Behind the rear seats
Behind the front seats Installation of the rod
Attach lower hook with opening facing backward to eye in the right and left of the floor. Adjust strap length on safety net by attaching the upper hook to the eyes of the strap. Keep strap under tension while proceeding with installation of rod.
Attach strap to eyes underneath the rear seat cushion.
Fold backrests forward.
To get a flat load bay, first fold seat cushion before attaching the safety net. Move front seats forward to ease tension if necessary.
There are two installation openings in the roof frame: suspend and engage rod of net at one side, compress rod and suspend and engage at other side.
Removal
Unhook the safety net rods from the brackets in the roof frame. Detach straps from the eyes. Roll up the net and secure with a strap.
The removed safety net can be stored
under the rear floor cover 3 81.
Warning triangle
5-door hatchback
Sports tourer
Storage
First aid kit
5-door hatchback
87
Stow the warning triangle in the space behind the strap on the right side of the load compartment.
Fold down straps. Stow the warning triangle in the space behind the straps on the inside of the tailgate.
Stow the first aid kit in the stowage compartment behind the warning triangle.
Before first use, press in the interior trim at the top and at the sides of the perforation. Then fold the trim outward to gain access to the stowage compartment.
88 Storage
Sports tourer
Fold down strap. Stow the first aid kit in the space behind a strap on the inside of the tailgate.
Roof rack system
Roof rack
For safety reasons and to avoid damage to the roof, the vehicle approved roof rack system is recommended. For further information contact your workshop.
Follow the installation instructions and remove the roof rack when not in use.
Mounting roof rack
5-door hatchback
Detach the cover from each mounting point by using a coin.
Sports tourer with roof railing
To fasten the roof rack, insert the mounting bolts in the holes indicated in the illustration.
Loading information
■ Use the four hooks at the sidewalls of the load compartment for hanging up carrier bags. Maximum load: 5 kg per hook.
■ Heavy objects in the load compartment should be placed against the seat backrests. Ensure that the backrests are securely engaged. If objects can be stacked, heavier objects should be placed at the bottom.
■ Secure objects with lashing straps
attached to the lashing eyes 3 83.
Attach the height adjustable cover
in the lowest position (1) 3 81.
■ Sports tourer: Use the hooks at the sidewalls of the load compartment for hanging up carrier bags. Press to fold out the hook.
■ Secure loose objects in the load compartment to prevent them from sliding.
■ When transporting objects in the load compartment, the backrests of the rear seats must not be angled forward.
Storage 89
■ Do not allow the load to protrude above the upper edge of the backrests.
■ Do not place any objects on the load compartment cover or the instrument panel, and do not cover the sensor on top of the instrument panel.
■ The load must not obstruct the operation of the pedals, parking brake and gear selector lever, or hinder the freedom of movement of the driver. Do not place any unsecured objects in the interior.
■ Do not drive with an open load compartment.
9 Warning
Always make sure that the load in the vehicle is securely stowed.
Otherwise objects can be thrown around inside the vehicle and cause personal injury or damage to the load or car.
■ The payload is the difference between the permitted gross
90 Storage
vehicle weight (see identification
weight.
To calculate the payload, enter the data for your vehicle in the Weights table at the front of this manual.
The EC kerb weight includes weights for the driver (68 kg), luggage (7 kg) and all fluids (tank
90 % full).
Optional equipment and accessories increase the kerb weight.
■ Driving with a roof load increases the sensitivity of the vehicle to cross-winds and has a detrimental effect on vehicle handling due to the vehicle's higher centre of gravity. Distribute the load evenly and secure it properly with retaining straps. Adjust the tyre pressure and vehicle speed according to the load conditions. Check and retighten the straps frequently.
Do not drive faster than 75 mph.
The permissible roof load is 75 kg for the 5-door hatchback and
100 kg for the Sports tourer. The roof load is the combined weight of the roof rack and the load.
Instruments and controls
Controls ....................................... 91
Warning lights, gauges and
indicators ..................................... 98
Information displays ................... 109
Vehicle messages ...................... 114
Trip computer ............................. 118
Vehicle personalisation .............. 121
Controls
Steering wheel adjustment
Instruments and controls
Steering wheel controls
91
Unlock lever, adjust steering wheel, then engage lever and ensure it is fully locked.
Do not adjust steering wheel unless vehicle is stationary and steering wheel lock has been released.
The Infotainment system, the cruise control and a connected mobile phone can be operated via the controls on the steering wheel.
Further information is available in the
Infotainment system manual.
92 Instruments and controls
Heated steering wheel Horn
Activate heating by pressing * button. Activation is indicated by the
LED in the button.
The recommended grip areas of the steering wheel are heated quicker and to a higher temperature than the other areas.
Heating is operational when the engine is running and during an
Autostop.
Press j.
Windscreen wiper/washer
Windscreen wiper
Adjustable wiper interval
Instruments and controls
Automatic wiping with rain sensor
93
2 = fast
1 = slow
P = interval wiping
§ = off
For a single wipe when the windscreen wiper is off, press the lever down.
Do not use if the windscreen is frozen.
Switch off in car washes.
Wiper lever in position P.
Turn the adjuster wheel to adjust the desired wipe interval: short interval long interval
= turn adjuster wheel upwards
= turn adjuster wheel downwards
P = automatic wiping with rain sensor
The rain sensor detects the amount of water on the windscreen and automatically regulates the frequency of the windscreen wiper.
If the wiper frequency is above
20 seconds the wiper arm moves slightly down to park position.
94 Instruments and controls
Adjustable sensitivity of the rain sensor
Windscreen and headlight washer
Turn the adjuster wheel to adjust the sensitivity: low sensitivity high sensitivity
= turn adjuster wheel downwards
= turn adjuster wheel upwards
Keep the sensor free from dust, dirt and ice.
Pull lever. Washer fluid is sprayed onto the windscreen and the wiper wipes a few times.
If the headlights are on, washer fluid is also sprayed onto the headlights, provided that the lever is pulled sufficiently long. Afterwards the headlight washer system is inoperable for 5 wash cycles or until engine or headlights have been switched off and on again.
Rear window wiper/washer
Instruments and controls
The rear window washer system is deactivated when the fluid level is low.
Outside temperature
95
Press the rocker switch to activate the rear window wiper: upper position lower position middle position
= continuous operation
= intermittent operation
= off
Push lever. Washer fluid is sprayed onto the rear window and the wiper wipes a few times.
Do not use if the rear window is frozen.
Switch off in car washes.
The rear window wiper comes on automatically when the windscreen wiper is switched on and reverse gear is engaged.
Activation or deactivation of this function can be changed in the menu
Settings in the Info-Display.
Vehicle personalisation 3 121.
A drop in temperature is indicated immediately and a rise in temperature after a time delay.
96 Instruments and controls
If outside temperature drops to 3 °C, a warning message is displayed in the
Driver Information Centre with
Uplevel-Display or Uplevel-Combi-
Display.
9 Warning
The road surface may already be icy even though the display indicates a few degrees above
0 °C.
Clock
Date and time are shown in the
Info-Display.
Set date and time
Press the CONFIG button. The menu
Settings is displayed.
Select Time & Date.
■ Set date format: Changes indication of date between MM/DD/
YYYY and DD.MM.YYYY.
■ Display digital clock: Switches on/ off indication of time on the display.
■ RDS clock synchronization: The
RDS signal of most VHF transmitters automatically sets the time. RDS time synchronisation can take a few minutes. Some transmitters do not send a correct time signal. In such cases, it is recommended to switch off automatic time synchronisation.
Vehicle personalisation 3 121.
Selectable setting options:
■ Set time: Changes the time shown on the display.
■ Set date: Changes the date shown on the display.
■ Set time format: Changes indication of hours between 12 hours and 24 hours.
Power outlets
A 12 Volt power outlet is located in the front console.
A further 12 Volt power outlet is located in the rear console. Fold the cover downwards.
Sports tourer: A 12 Volt power outlet is located at the left sidewall in the load compartment.
Do not exceed the maximum power consumption of 120 watts.
With ignition off, the power outlets are deactivated. Additionally the power outlets are deactivated in the event of low battery voltage.
Electrical accessories that are connected must comply with the electromagnetic compatibility requirements laid down in
DIN VDE 40 839.
Do not connect any current-delivering accessories, e.g. electrical charging devices or batteries.
Do not damage the outlet by using unsuitable plugs.
Instruments and controls
Cigarette lighter
97
The cigarette lighter is located in the front console.
Press in cigarette lighter. It switches off automatically once the element is glowing. Pull out lighter.
Ashtrays
Caution
To be used only for ash and not for combustible rubbish.
98 Instruments and controls
Warning lights, gauges and indicators
Instrument cluster
In some versions, the needles of the instruments briefly rotate to the end position when the ignition is switched on.
Speedometer
The portable ashtray can be placed in the cupholders.
Odometer
The bottom line displays the recorded distance in miles.
Trip odometer
The top line displays the recorded distance since the last reset.
To reset, hold the reset knob depressed for a few seconds with the ignition on.
Indicates vehicle speed.
Tachometer Fuel gauge
Instruments and controls 99
Because of the fuel remaining in the tank, the top-up quantity may be less than the specified tank capacity.
Fuel selector
Displays the engine speed.
Drive in a low engine speed range for each gear as much as possible.
Caution
If the needle is in the red warning zone, the maximum permitted engine speed is exceeded. Engine at risk.
Displays the fuel level or gas level in the tank depending on the operation mode.
Control indicator i illuminates if the level in the tank is low. Refuel immediately if it flashes.
During liquid gas operation, the system automatically switches over to petrol operation when gas tanks are
Never run the tank dry.
Pressing button LPG switches between petrol and liquid gas operation. The LED 1 status shows the current operating mode.
1 off = petrol operation
1 illuminates = liquid gas
1 flashes operation
= no switching is possible, one type of fuel is empty
100 Instruments and controls
As soon as the liquid gas tanks are empty, petrol operation is automatically engaged until the ignition is switched off.
Fuel for liquid gas operation 3 170.
Engine coolant temperature gauge
Caution
If engine coolant temperature is too high, stop vehicle, switch off engine. Danger to engine. Check coolant level.
Service display
The engine oil life system lets you know when to change the engine oil and filter. Based on driving conditions, the interval at which an engine oil and filter change will be indicated can vary considerably.
In the Uplevel-Display or Uplevel-
Combi-Display, the remaining oil life duration is displayed in the Vehicle
Information Menu.
In the Midlevel-Display, the remaining engine oil life duration is displayed by the control indicator I, therefore the ignition must be switched on, with the engine not running.
The menu and function can be selected via the buttons on the turn signal lever.
To display the remaining engine oil life duration:
Displays the coolant temperature.
left area = engine operating temperature not yet central area reached
= normal operating temperature right area = temperature too high
Press the MENU button to select the
Vehicle Information Menu.
Turn the adjuster wheel to select
Remaining Oil Life.
The system must be reset every time the engine oil is changed to allow proper functionality. Seek the assistance of a workshop.
Press the SET/CLR button to reset.
Therefore the ignition must be switched on, with the engine not running.
When the system has calculated that engine oil life has been diminished,
Change Engine Oil Soon or a warning code appears in the Driver
Information Centre. Have engine oil and filter changed by a workshop within one week or 300 miles
(whichever occurs first).
Driver Information Centre 3 109.
Control indicators
The control indicators described are not present in all vehicles. The description applies to all instrument versions. Depending on the equipment, the position of the control indicators may vary. When the ignition is switched on, most control indicators will illuminate briefly as a functionality test.
The control indicator colours mean: red = danger, important reminder yellow = warning, information, fault green = confirmation of activation blue = confirmation of activation white = confirmation of activation
Instruments and controls 101
102 Instruments and controls
Control indicators in the instrument cluster
Control indicators in the centre console
Turn signal
O illuminates or flashes green.
Illuminates briefly
The parking lights are switched on.
Flashes
A turn signal or the hazard warning flashers are activated.
Rapid flashing: failure of a turn signal light or associated fuse, failure of turn signal light on trailer.
Seat belt reminder
Seat belt reminder on front seats
X for driver's seat illuminates or flashes red.
k for front passenger seat illuminates or flashes red, when seat is occupied.
Illuminates
After the ignition has been switched on until the seat belt has been fastened.
Flashes
After having started the engine for a maximum of 100 seconds until the seat belt has been fastened.
Airbag and belt tensioners
v illuminates red.
Instruments and controls 103
When the ignition is switched on, the control indicator illuminates for approx. 4 seconds. If it does not illuminate, does not go out after
4 seconds or illuminates whilst driving, there is a fault in the airbag system. Seek the assistance of a workshop. The airbags and belt pretensioners may fail to trigger in the event of an accident.
Deployment of the belt pretensioners or airbags is indicated by continuous illumination of v.
9 Warning
Have the cause of the fault remedied immediately by a workshop.
Belt pretensioners, airbag system
Airbag deactivation
V illuminates yellow.
Illuminates for approx. 60 seconds after the ignition is switched on. The front passenger airbag is activated.
104 Instruments and controls
* illuminates yellow.
The front passenger airbag is
9 Danger
Risk of fatal injury for a child using a child restraint system together with activated front passenger airbag.
Risk of fatal injury for an adult person with deactivated front passenger airbag.
Charging system
p illuminates red.
Illuminates when the ignition is switched on and extinguishes shortly after the engine starts.
Illuminates when the engine is running
Stop, switch off engine. Battery is not charging. Engine cooling may be interrupted. The brake servo unit may cease to be effective. Seek the assistance of a workshop.
Malfunction indicator light
Z illuminates or flashes yellow.
Illuminates when the ignition is switched on and extinguishes shortly after the engine starts.
Illuminates when the engine is running
Fault in the emission control system.
The permitted emission limits may be exceeded. Seek the assistance of a workshop immediately.
Flashes when the engine is running
Fault that could lead to catalytic converter damage. Ease up on the accelerator until the flashing stops.
Seek the assistance of a workshop immediately.
Service vehicle soon
g illuminates yellow.
Additionally a warning message or a warning code is displayed.
The vehicle needs a service.
Seek the assistance of a workshop.
Brake and clutch system
Brake and clutch fluid level
& illuminates red.
The brake and clutch fluid level is too
9 Warning
Stop. Do not continue your journey. Consult a workshop.
Illuminates after the ignition is switched on if the manual parking
Operate pedal
illuminates or flashes yellow.
Clutch pedal needs to be operated to start the engine. Stop-start system
Illuminates
Brake pedal needs to be operated to release the electrical parking brake
Flashes
Clutch pedal needs to be operated to
Electrical parking brake
m illuminates or flashes red.
Illuminates
Electrical parking brake is applied
Flashes
Electrical parking brake is not fully applied or released. Switch on ignition, depress brake pedal and attempt to reset the system by first releasing and then applying the electrical parking brake. If m remains flashing, do not drive and seek the assistance of a workshop.
Electrical parking brake fault
j illuminates or flashes yellow.
Illuminates
Electrical parking brake is operating
with degraded performance 3 157.
Flashes
Electrical parking brake is in service mode. Stop vehicle, apply and release the electrical parking brake to reset.
9 Warning
Have the cause of the fault remedied immediately by a workshop.
Antilock brake system
(ABS)
u illuminates yellow.
Illuminates for a few seconds after the ignition is switched on. The system is ready for operation when the control indicator extinguishes.
Instruments and controls 105
If the control indicator does not go out after a few seconds, or if it illuminates while driving, there is a fault in the
ABS. The brake system remains operational but without ABS regulation.
Upshift
[ illuminates green, or is shown as a symbol in the Driver Information
Centre with Uplevel-Display or
Uplevel-Combi-Display.
Upshifting is recommended for fuel saving.
Power steering
c illuminates yellow.
Illuminates with power steering reduced
Power steering is reduced due to overheating of the system. Control indicator extinguishes when the system has cooled down.
106 Instruments and controls
Illuminates with power steering disabled
Failure in the power steering system.
Consult a workshop.
Lane departure warning
) illuminates green or flashes yellow.
Illuminates green
System is switched on and ready to operate.
Flashes yellow
System recognizes an unintended lane change.
Ultrasonic parking assist
r illuminates yellow.
Fault in system or
Fault due to sensors that are dirty or covered by ice or snow or
Interference due to external sources of ultrasound. Once the source of interference is removed, the system will operate normally.
Have the cause of the fault in the system remedied by a workshop.
Ultrasonic parking assist 3 163.
Electronic Stability Control off
n illuminates yellow.
The system is deactivated.
Electronic Stability Control and Traction Control system
b illuminates or flashes yellow.
Illuminates
A fault in the system is present.
Continued driving is possible. Driving stability, however, may deteriorate depending on road surface conditions.
Have the cause of the fault remedied by a workshop.
Flashes
The system is actively engaged.
Engine output may be reduced and the vehicle may be braked automatically to a small degree.
Electronic Stability Control 3 159,
Traction Control system 3 159.
Traction Control system off
k illuminates yellow.
The system is deactivated.
Preheating
!
illuminates yellow.
Preheating is activated. Only activates when outside temperature is low.
Diesel particle filter
% illuminates or flashes yellow.
The diesel particle filter requires cleaning.
Continue driving until % extinguishes. If possible, do not allow engine speed to drop below
2000 rpm.
Illuminates
The diesel particle filter is full. Start cleaning process as soon as possible.
Flashes
The maximum filling level of the filter is reached. Start cleaning process immediately to avoid damage to the engine.
Diesel particle filter 3 150, Stop-start
Tyre pressure monitoring system
w illuminates or flashes yellow.
Illuminates
Tyre pressure loss. Stop immediately and check tyre pressure.
Flashes
Fault in system or tyre without pressure sensor mounted (e.g. spare wheel). After 60-90 seconds the control indicator illuminates continuously. Consult a workshop.
Engine oil pressure
I illuminates red.
Illuminates when the ignition is switched on and extinguishes shortly after the engine starts.
Illuminates when the engine is running
Caution
Engine lubrication may be interrupted. This may result in damage to the engine and/or locking of the drive wheels.
1. Depress clutch.
2. Select neutral gear, set selector lever to N.
Instruments and controls 107
3. Move out of the flow of traffic as quickly as possible without impeding other vehicles.
4. Switch off ignition.
9 Warning
When the engine is off, considerably more force is needed to brake and steer. During an
Autostop the brake servo unit will still be operational.
Do not remove key until vehicle is stationary, otherwise the steering wheel lock could engage unexpectedly.
Check oil level before seeking the
assistance of a workshop 3 183.
Low fuel
i illuminates or flashes yellow.
Illuminates
Level in fuel tank is too low.
108 Instruments and controls
Flashes
Fuel used up. Refuel immediately.
Never run the tank dry.
Bleeding the diesel fuel system
Immobiliser
d flashes yellow.
Fault in the immobiliser system. The engine cannot be started.
Reduced engine power
# illuminates yellow.
The engine power is limited. Consult a workshop.
Exterior light
8 illuminates green.
The exterior lights are on 3 126.
High beam
C illuminates blue.
Illuminated when high beam is on or
during headlight flash 3 127, or when
high beam is on with high beam assist, adaptive forward lighting
High beam assist
l illuminates green.
The high beam assist is activated,
see adaptive forward lighting 3 129.
Adaptive forward lighting
f illuminates or flashes yellow.
Illuminates
Fault in system.
Seek the assistance of a workshop.
Flashes
System switched to symmetrical low beam.
Control indicator f flashes for approx.
4 seconds after the ignition is switched on as a reminder that the
system has been activated 3 128.
Automatic light control 3 127.
Fog light
> illuminates green.
The front fog lights are on 3 132.
Rear fog light
r illuminates yellow.
The rear fog light is on 3 132.
Low washer fluid
G illuminates yellow.
The washer fluid level is low.
Cruise control
m illuminates white or green.
Illuminates white
The system is on.
Illuminates green
Cruise control is active.
Door open
h illuminates red.
A door or the tailgate is open.
Information displays
Driver Information Centre
Instruments and controls 109
The Driver Information Centre (DIC) is located in the instrument cluster between speedometer and tachometer. It is available as
Midlevel-Display, Uplevel-Display or
Uplevel-Combi-Display.
The following main menus, depending on the vehicle configuration, can be selected:
■ Vehicle Information Menu
■ Trip/Fuel Information Menu
110 Instruments and controls
Selecting menus and functions
The menus and functions can be selected via the buttons on the turn signal lever.
In the Uplevel-Combi-Display, the menus can be selected by the
MENU button, indicated by symbols in the top line of the display:
X = Vehicle Information Menu
W = Trip/Fuel Information Menu
Some of the displayed functions differ between vehicle driving and standstill and some functions are only active when the vehicle is driving.
Vehicle personalisation 3 121.
Press the MENU button to switch between the menus or to return from a submenu to the next higher menu level.
Turn the adjuster wheel to highlight a menu option or to set a numeric value.
Press the SET/CLR button to select a function or to confirm a message.
Vehicle Information Menu
Press the MENU button to select the
Vehicle Information Menu, or on
Uplevel-Combi-Display select X.
Turn the adjuster wheel to select one of the submenus. Press the SET/
CLR button to confirm.
Follow the instructions given in the submenus.
Instruments and controls 111
Possible submenus:
■ Unit: Displayed units can be changed
■ Speed Warning: If exceeding the preset speed, a warning chime will be activated
■ Traffic Sign Assistant: displays detected traffic signs for the current
Selection and indication can be different between Midlevel-, Uplevel-, and Uplevel-Combi-Display.
Trip/Fuel Information Menu
Press the MENU button to select the
Trip/Fuel Information Menu, or select
W on Uplevel-Combi-Display.
Turn the adjuster wheel to select one of the submenus. Press the SET/
CLR button to confirm.
■ Trip odometer 1
■ Trip odometer 2
■ Digital speed
Trip odometer 2 and digital speed are only available on vehicles with
Uplevel-Display or Uplevel-Combi-
Display.
On vehicles with trip computer more submenus are available.
Trip/Fuel Information Menu, Trip
112 Instruments and controls
Graphic-Info-Display,
Colour-Info-Display
Depending on the vehicle configuration the vehicle has a Graphic- or Colour-Info-Display.
The Info-Display is located in the instrument panel above the
Infotainment system.
Graphic-Info-Display
Graphic-Info-Display indicates:
■ Infotainment system, see description in the Infotainment system manual
■ settings for vehicle personalisation
Depending on the Infotainment system, the Graphic-Info-Display is available in two versions.
Colour-Info-Display
The Colour-Information-Display indicates in colour:
■ Infotainment system, see description in the Infotainment system manual
■ navigation, see description in the
Infotainment system manual
■ system settings
■ settings for vehicle personalisation
The type of information and how it is displayed depends on the equipment of the vehicle and the settings made.
Selecting menus and settings
Menus and settings are accessed via the display.
Selections are made via:
■ menus
■ function buttons and multifunction knob of the Infotainment system
Selecting with the Infotainment system
Select a function via the Infotainment system buttons. The menu of the selected function is displayed.
The multifunction knob is used to select an item and to confirm.
Multifunction knob
The multifunction knob is the central control element for the menus:
Turn
■ To mark a menu option
■ To set a numeric value or to display a menu option
Instruments and controls 113
Press (the outer ring)
■ To select or activate the marked option
■ To confirm a set value
■ To switch a system function on/off
BACK button
Press button to:
■ exit a menu without changing settings
■ return from a submenu to a higher menu level
■ delete the last character in a character sequence
Press and hold the button for a few seconds to delete the entire entry.
Vehicle personalisation 3 121.
114 Instruments and controls
Vehicle messages
Messages are indicated mainly in the
Driver Information Centre (DIC), in some cases together with a warning and signal buzzer.
Press the SET/CLR button, the
MENU button or turn the adjuster wheel to confirm a message.
Vehicle messages on the
Midlevel-Display
The vehicle messages are displayed as code numbers.
No. Vehicle message
2 No radio remote control detected, depress clutch pedal for a restart
3 Engine coolant level low
4 Air conditioning off
5 Steering wheel is locked
No. Vehicle message
6 Depress brake pedal to release electrical parking brake
7 Turn steering wheel, switch ignition off and then on
9 Turn steering wheel, start engine again
12 Vehicle overloaded
13 Compressor overheated
15 Centre high-mounted brake light failure
16 Brake light failure
17 Headlight levelling malfunction
18 Left low beam failure
19 Rear fog light failure
20 Right low beam failure
21 Left sidelight failure
22 Right sidelight failure
23 Reversing light failure
No. Vehicle message
24 Number plate light failure
25 Left front turn signal failure
26 Left rear turn signal failure
27 Right front turn signal failure
28 Right rear turn signal failure
29 Check trailer brake light
30 Check trailer reversing light
31 Check left trailer turn signal
32 Check right trailer turn signal
33 Check trailer rear fog light
34 Check trailer rear light
35 Replace battery in radio remote control
48 Clean side blind zone alert system
49 Lane departure warning unavailable
53 Tighten gas cap
No. Vehicle message
54 Water in diesel fuel filter
55 Diesel particle filter is full
56 Tyre pressure imbalance on front axle
57 Tyre pressure imbalance on rear axle
58 Tyres without TPMS sensors detected
59 Open and then close driver window
60 Open and then close front passenger window
61 Open and then close rear left window
62 Open and then close rear right window
65 Theft attempted
66 Service theft alarm system
67 Service steering wheel lock
Instruments and controls 115
No. Vehicle message
68 Service power steering
69 Service suspension system
70 Service level control system
71 Service rear axle
74 Service AFL
75 Service air conditioning
76 Service side blind zone alert system
77 Service lane departure warning
78 Service pedestrian protection system
79 Top up engine oil
81 Service transmission
82 Change engine oil soon
83 Service adaptive cruise control
84 Engine power is reduced
94 Shift to park before exiting
116 Instruments and controls
No. Vehicle message
95 Service airbag
128 Bonnet open
134 Park assist fault, clean bumper
136 Service parking assist
145 Check washer fluid level
174 Low battery
258 Park assist off
Vehicle messages on the
Uplevel-Display or Uplevel-
Combi-Display
The vehicle messages are displayed as text. Follow the instructions given in the messages.
The system displays messages regarding the following topics:
■ Fluid levels
■ Anti-theft alarm system
■ Brakes
■ Drive systems
■ Ride control systems
■ Cruise control
■ Object detection systems
■ Lighting, bulb replacement
■ Wiper/washer system
■ Doors, windows
■ Radio remote control
■ Seat belts
■ Airbag systems
■ Engine and transmission
■ Tyre pressure
■ Diesel particle filter
■ Battery
Vehicle messages on the
Colour-Info-Display
Some important messages appear additionally in the
Colour-Info-Display. Press the multifunction knob to confirm a message. Some messages only pop up for a few seconds.
Warning chimes
When starting the engine or whilst driving
Only one warning chime will sound at a time.
The warning chime regarding unfastened seat belts has priority over any other warning chime.
■ If seat belt is not fastened.
■ If a door or the tailgate is not fully closed when starting off.
■ If a certain speed is exceeded with parking brake applied.
■ If a programmed speed is exceeded.
■ If a warning message or a warning code appears in the Driver
Information Centre.
■ If the parking assist detects an object.
■ If the reverse gear is engaged and the rear end carrier extended.
■ If the diesel particle filter has reached the maximum filling level.
When the vehicle is parked and/ or the driver's door is opened
■ When the key is in the ignition switch.
■ With exterior lights on.
During an Autostop
■ If the driver's door is opened.
Battery voltage
When the battery voltage is running low, a warning message or warning code 174 will appear in the Driver
Information Centre.
1. Switch off immediately electrical consumers which are not required for a safe ride, such as seat heating, heated rear window or other main consumers.
2. Charge the battery by driving continuously for a while or by using a charging device.
The warning message or warning code will disappear after the engine has been started two times consecutively without voltage drop.
Instruments and controls 117
If the battery cannot be recharged, have the cause of the fault remedied by a workshop.
118 Instruments and controls
Trip computer
The menus and functions can be selected via the buttons on the turn signal lever.
Trip/Fuel Information Menu on
Uplevel-Display
Turn the adjuster wheel to select one of the submenus:
■ Trip odometer 1
■ Trip odometer 2
■ Range
■ Average consumption
■ Instantaneous consumption
■ Average speed
■ Digital speed
■ Traffic sign assistant
■ Route guidance
Trip/Fuel Information Menu on
Uplevel-Combi-Display
Turn the adjuster wheel to select the submenus:
Press the MENU button to select the
Trip/Fuel Information Menu, or select
W on the Uplevel-Combi-Display.
■ Trip odometer 2
■ Average consumption 2
■ Average speed 2
Instruments and controls 119
■ Trip odometer 1
■ Average consumption 1
■ Average speed 1
■ Digital speed
■ Range
■ Instantaneous consumption
■ ECO drive assistant
■ Route guidance
Trip computer 1 and 2
The information of two trip computers can be reset separately for odometer, average consumption and average speed, making it possible to display different trip information for different drivers.
To reset, press the SET/CLR button in each mode for a few seconds.
120 Instruments and controls
Trip odometer
Trip odometer displays the recorded distance since a certain reset.
Range
Range is calculated from current fuel tank content and current consumption. The display shows average values.
After refuelling, the range is updated automatically after a brief delay.
When the fuel level in the tank is low, a message appears on vehicles with
Uplevel-Display or Uplevel-Combi-
Display.
When the tank has to be refuelled immediately, a warning code or warning message is displayed on vehicles with Midlevel- and Uplevel-
Display or Uplevel-Combi-Display.
Additionally the control indicator i in the fuel gauge illuminates or flashes
Average consumption
Display of average consumption. The measurement can be reset at any time and starts with a default value.
To reset, press the SET/CLR button for a few seconds.
Instantaneous consumption
Display of the instantaneous consumption.
Average speed
Display of average speed. The measurement can be reset at any time.
To reset, press the SET/CLR button for a few seconds.
Digital speed
Digital display of the instantaneous speed.
Traffic sign assistant
Indicates detected traffic signs for the
ECO drive assistant
An arrow indicates a recommended upshifting for fuel saving.
Additionally a bar indicates if the current driving is economical. A full bar indicates most economical driving.
Route guidance
Additionally to the navigation information in the Color-Info-Display, route guidance is displayed in the
Driver Info Center.
Instruments and controls 121
Vehicle personalisation
The vehicle's behaviour can be personalised via changing the settings in the Info-Display.
Some of the personal settings for different drivers can be memorised individually for each vehicle key.
Depending on vehicle equipment and country-specific regulations some of the functions described below might not be available.
Some functions are only displayed or active when the engine is running.
Personal settings in the
Graphic-Info-Display
Press the CONFIG button. The menu
Settings is displayed.
The following settings can be selected by turning and pressing the multifunction knob:
■ Sport mode settings
■ Languages
■ Time Date
■ Radio settings
■ Phone settings
■ Vehicle settings
In the corresponding submenus the following settings can be changed:
122 Instruments and controls
Sport mode settings
The driver can select the functions which will be activated in Sport mode
■ Sport suspension: Damping becomes harder.
■ Sport powertrain performance:
Accelerator pedal and gear change characteristics become more responsive.
■ Sport steering: Steering support is reduced.
■ Swap backlight colour main instr.:
Change of instrument illumination colour.
Languages
Selection of the desired language.
Time Date
Radio settings
See description for Infotainment system in the Infotainment system manual.
Phone settings
See description for Infotainment system in the Infotainment system manual.
Vehicle settings
■ Climate and air quality
Auto fan speed: Modifies the fan regulation. Changed setting will be active after switching the ignition off and on again.
Climate control mode: Activates or deactivates the cooling every time the ignition is switched on or uses the last chosen setting.
Auto demist: Supports windscreen dehumidification by automatically selecting the necessary settings and auto air conditioning mode.
Auto rear demist: Activates automatically rear heated window.
■ Comfort settings
Chime volume: Changes the volume of warning chimes.
Personalization by driver: Activates or deactivates the personalisation function.
Rear auto wipe in reverse:
Activates or deactivates automatically switching on of the
rear window wiper when reverse gear is engaged.
■ Park assist / Collision detection
Park assist: Activates or deactivates the ultrasonic parking assist.
■ Exterior ambient lighting
Duration upon exit of vehicle:
Activates or deactivates and change the duration of exit lighting.
Exterior lighting by unlocking:
Activates or deactivates the welcome lighting.
■ Power door locks
Auto door unlock: Activates or deactivates the automatic door unlocking function after switching off ignition.
Auto door lock: Activates or deactivates the automatic door locking function after driving off.
Stop door lock if door open:
Activates or deactivates the automatic door locking function while a door is open.
Delayed door lock: Activates or deactivates the delayed door locking function.
■ Remote locking, unlocking, starting
Remote unlock feedback: Activates or deactivates the hazard warning flasher feedback whilst unlocking.
Remote door unlock: Changes the configuration to unlock only the driver's door or the whole vehicle whilst unlocking.
Auto relock doors: Activates or deactivates the automatic relock function after unlocking without opening the vehicle.
■ Restore factory settings
Restore factory settings: Reset all settings to the default settings.
Instruments and controls
Personal settings in the
Colour-Info-Display
123
Press the CONFIG button. The menu
Settings is displayed.
124 Instruments and controls
The following settings can be selected by turning and pressing the multifunction knob:
■ Sport mode settings
■ Languages
■ Time & Date
■ Radio settings
■ Phone settings
■ Navigation settings
■ Vehicle settings
■ Display settings
In the corresponding submenus the following settings can be changed:
Sport mode settings
The driver can select the functions which will be activated in Sport mode
■ Sport suspension: Damping becomes harder.
■ Sport powertrain performance:
Accelerator pedal and gear change characteristics become more responsive.
■ Sport steering: Steering support is reduced.
■ Swap backlight colour main instr.:
Change of instrument illumination colour.
Languages
Selection of the desired language.
Time & Date
Radio settings
See description for Infotainment system in the Infotainment system manual.
Phone settings
See description for Infotainment system in the Infotainment system manual.
Navigation settings
See description for Infotainment system in the Infotainment system manual.
Vehicle settings
■ Climate and air quality
Auto fan speed: Modifies the fan regulation. Changed setting will be active after switching the ignition off and on again.
Climate control mode: Activates or deactivates cooling when switching on the ignition or uses the last chosen setting.
Auto demist: Supports windscreen dehumidification by automatically selecting the necessary settings and auto air conditioning mode.
Auto rear demist: Activates automatically the rear heated window.
■ Comfort settings
Chime volume: Changes the volume of warning chimes.
Rear auto wipe in reverse:
Activates or deactivates automatically switching on of the rear window wiper when reverse gear is engaged.
■ Park assist / Collision detection
Park assist: Activate or deactivate the ultrasonic parking assist.
■ Exterior ambient lighting
Duration upon exit of vehicle:
Activates or deactivates and changes the duration of exit lighting.
Exterior lighting by unlocking:
Activates or deactivates the welcome lighting.
■ Power door locks
Auto door unlock: Activates or deactivates the automatic door unlocking function after switching off ignition.
Auto door lock: Activates or deactivates the automatic door locking function after driving off.
Prevent doorlock while door open:
Activates or deactivates the
Instruments and controls 125
automatic door locking function while a door is open.
■ Lock / Unlock / Start by remote
Remote unlock feedback: Activates or deactivates the hazard warning flasher feedback whilst unlocking.
Remote door unlock: Changes the configuration to unlock only the driver's door or the whole vehicle whilst unlocking.
Auto relock doors: Activates or deactivates the automatic relock function after unlocking without opening the vehicle.
■ Restore factory settings
Restore factory settings: Resets all settings to the default settings.
Display settings
Selectable display settings:
■ Day mode: Optimisation for daylight conditions.
■ Night mode: Optimisation for darkness.
■ Automatic mode: The display changes mode when the vehicle lights are switched on/off.
126 Lighting
Lighting
Exterior lighting .......................... 126
Interior lighting ........................... 133
Lighting features ........................ 134
Exterior lighting
Light switch
Light switch with Automatic light control
Turn light switch:
7 = lights off
8 = sidelights
9 = headlights
Turn light switch:
AUTO = automatic light control:
Headlights are switched on and off automatically depending on external m lighting conditions.
= activation or deactivation of the automatic light control. Switch turns back
8
9 to AUTO.
= sidelights
= headlights
In the Driver Information Centre with
Uplevel-Display or Uplevel-Combi-
Display, the current status of the automatic light control is displayed.
When switching on the ignition, automatic light control is active.
When headlights are on, 8 lights up.
Tail lights
Tail lights are illuminated together with headlights and sidelights.
Automatic light control
Tunnel detection
When a tunnel is entered the headlights are switched on without any delay.
Adaptive forward lighting 3 129.
High beam
Lighting 127
When the automatic light control function is switched on and the engine is running, the system switches between daytime running light and headlights automatically depending on the lighting conditions and information given by the rain sensor system.
Daytime running light
Daytime running light increases visibility of the vehicle during daylight.
While the daytime running light is active, the tail lights are switched on or off depending on country-specific variant.
Automatic headlight activation
During poor lighting conditions the headlights are switched on.
Furthermore the headlights are switched on if the windscreen wipers have been activated for several wipes.
To switch from low to high beam, push lever.
To switch to low beam, push lever again or pull.
128 Lighting
Headlight flash
To activate the headlight flash, pull lever.
Headlight range adjustment
Manual headlight range adjustment
To adapt headlight range to the vehicle load to prevent dazzling: turn thumb wheel ? to required position.
0 = front seats occupied
1 = all seats occupied
2 = all seats occupied and load compartment laden
3 = driver's seat occupied and load compartment laden.
Dynamic automatic headlight
Headlights when driving abroad
The asymmetrical headlight beam extends visibility at the edge of the road at the passenger side.
However, when driving in countries where traffic drives on the opposite side of the road, adjust the headlights to prevent dazzling of oncoming traffic.
Vehicles with halogen headlight system
The headlights do not have to be adjusted.
Vehicles with Xenon headlight system
1. Key in ignition switch.
2. Pull turn signal lever and hold
(headlight flash).
3. Switch on ignition.
4. After approx. 5 seconds the control indicator f starts flashing and an acoustic signal sounds.
Every time the ignition is switched on, f flashes as a reminder for approx.
4 seconds.
For deactivation operate the same procedure as described above. f will not flash when function is deactivated.
Adaptive forward lighting
The Adaptive forward lighting functions are only available with Bi-
Xenon headlights. Light range, light distribution and intensity of light are variably triggered depending on the light conditions, weather and road type.
With the light switch in position
AUTO all lighting functions are available.
The following functions are available also with light switch in position 9:
■ Dynamic curve lighting
■ Cornering light
■ Reversing function
■ Dynamic automatic headlight levelling
Lighting
Playstreet lighting
Activated automatically at low speed up to approx. 20 mph. The light beam is turned at an angle of 8° to the roadside.
Town lighting
Activated automatically at a speed range between approx. 25 and
34 mph and when street lights are detected by the light sensor. The light range is reduced by an extended light distribution.
Country lighting
Activated automatically at a speed range between approx. 34 and
70 mph. The beam of light and the brightness is different between the left and the right side.
Motorway lighting
Activated automatically at a speed above approx. 70 mph and minimal steering movements. It switches on after a delay or directly when the vehicle is powerfully accelerated. The light beam is longer and brighter.
The light beam pivots based on steering wheel angle and speed, improving lighting in curves.
129
Adverse weather lighting
Activated automatically up to a speed of approx. 43 mph, when the rain sensor recognizes condensation or the wiper operates continuously. The range, distribution and light intensity is regulated variably depending on visibility.
Dynamic curve lighting
130 Lighting
Corner lighting
On tight bends or when turning off, depending on the steering angle or the turn signal light, an additional left or right reflector is switched on which illuminates the road at a right angle to the direction of travel. It is activated up to a speed of 25 mph.
Reversing function
If the headlights are on and reverse gear is engaged, both corner lights are switched on. They remain illuminated for 20 seconds after disengaging reverse gear or until driving faster than 10 mph in a forward gear.
High Beam Assist
This feature allows high beam as main driving light by night and when vehicle speed is faster than 25 mph.
It switches to low beam when:
■ the camera in the windscreen detects the lights of oncoming or preceding vehicles
■ the vehicle speed is slower than
12 mph
■ it is foggy or snowy
■ driving in urban areas
If there are no restrictions detected, the system switches back to high beam.
Activation
The high beam assist is activated by pushing the indicator lever twice with a speed above 25 mph.
The green control indicator l illuminates continuously when the assist is activated, the blue one 7 illuminates when high beam is on.
Deactivation
Push indicator lever once. It is also deactivated when front fog lights are switched on.
If a headlight flash is activated when the high beam is on, the high beam assist will be deactivated.
If a headlight flash is activated when the high beam is off, the high beam assist will stay activated.
High beam assist is alwayas active after the ignition is switched on.
Dynamic automatic headlight levelling
To prevent oncoming traffic from dazzle, headlight levelling is automatically adjusted based on inclination information measured by front and rear axle, acceleration or deceleration and vehicle speed.
Fault in Adaptive forward lighting system
When the system detects a failure in the Adaptive forward lighting system, the system moves to a preset position to avoid dazzling of oncoming traffic.
If this is not possible the affected headlight will be automatically switched off. In any case one headlight will stay on. A warning is displayed in the Driver Information
Centre.
Hazard warning flashers
Lighting 131
In the event of an accident with airbag deployment the hazard warning flashers are activated automatically.
Turn and lane-change signals
lever up = right turn signal lever down = left turn signal
If the lever is moved past the resistance point, the turn signal is switched on constantly. When the steering wheel moves back, the turn signal is automatically deactivated.
Operated with the ¨ button.
132 Lighting
For three flashes, e.g. when changing lanes, press the lever until resistance is felt and then release.
When a trailer is connected, turn signal flashes six times when pressing the lever until resistance is felt and then releasing.
Move the lever to the resistance point and hold for longer indication.
Switch the turn signal off manually by moving the lever to its original position.
Front fog lights
Light switch in position AUTO: switching on front fog lights will switch headlights on automatically.
Rear fog lights
Parking lights
Operated with the r button.
Light switch in position AUTO: switching on rear fog light will switch headlights on automatically.
Light switch in position 8: rear fog light can only be switched on with front fog lights.
The vehicle rear fog light is deactivated when towing.
When the vehicle is parked, the parking lights on one side can be activated:
1. Switch off ignition.
2. Move turn signal lever all the way up (right parking lights) or down
(left parking lights).
Confirmed by a signal and the corresponding turn signal control indicator.
Operated with the > button.
Reversing lights
The reversing light comes on when the ignition is on and reverse gear is selected.
Misted light covers
The inside of the light housing may mist up briefly in poor, wet and cold weather conditions, in heavy rain or after washing. The mist disappears quickly by itself; to help switch on the headlights.
Interior lighting
Instrument panel illumination control
Brightness of the following lights can be adjusted when the exterior lights are on:
■ Instrument panel illumination
■ Info-Display
■ Illuminated switches and operation elements.
Turn thumb wheel A and hold until the desired brightness is obtained.
Lighting 133
On vehicles with light sensor, the brightness can only be adjusted when the exterior lights are on and the light sensor detects night conditions.
Interior lights
During entry and exit of the vehicle, the front and rear courtesy lights automatically switch on and then off after a delay.
Note
In the event of an accident with airbag deployment the courtesy lights are turned on automatically.
Front courtesy light
134 Lighting
Operate rocker switch: w = automatic switching on and off.
press u = on.
press v = off.
Rear courtesy lights
Reading lights
Illuminate in conjunction with the front courtesy light depending on rocker switch position.
Operated with s and t buttons in front and rear courtesy lights.
Sunvisor lights
Illuminates when the cover is opened.
Lighting features
Centre console lighting
Spotlight incorporated in the interior lighting comes on when headlights are switched on.
Entry lighting
Welcome lighting
Following lights are switched on for a short time by unlocking the vehicle with the radio remote control:
■ headlights,
■ tail lights,
■ reversing lights,
■ number plate lights,
■ instrument panel light,
■ interior lights,
■ puddle lights.
Some functions work only in the dark and facilitates locating the vehicle.
The lighting switches off immediately when the ignition key is turned to
Activation or deactivation of this function can be changed in the menu
Settings in the Info-Display. Vehicle
The settings can be saved for the key
The following lights will additionally switch on when the driver's door is opened:
■ all switches
■ Driver Information Centre
■ door pocket lights
Exit lighting
The following lights switch on if the key is removed from the ignition switch:
■ Interior lights
■ Instrument panel light (only when it is dark)
■ Puddle lights
They will switch off automatically after a delay and will be activated again if the driver's door is opened.
Headlights, tail lights, reversing lights and number plate lights illuminate the surrounding area for an adjustable time after leaving the vehicle.
Switching on
1. Switch off ignition.
2. Remove ignition key.
3. Open driver's door.
4. Pull turn signal lever.
5. Close driver's door.
If the driver's door is not closed the lights switch off after two minutes.
Lighting 135
Exit lighting is switched off immediately if the turn signal lever is pulled while the driver's door is open.
Activation, deactivation and duration of this function can be changed in the menu Settings in the Info-Display.
Vehicle personalisation 3 121.
The settings can be saved for the key
Battery discharge protection
Battery state of charge function
The function guarantees longest battery life via a generator with controllable power output and optimised power distribution.
To prevent discharge of the battery when driving, following systems are reduced automatically in two stages and finally switched off:
■ Auxiliary heater
■ Heated rear window and mirrors
■ Heated seats
■ Fan
136 Lighting
In the second stage a message which confirms the activation of the battery discharge protection will be displayed in the Driver Information Centre.
Switching off electric lights
To prevent discharge of the battery when the ignition is switched off, some interior lights are switched off automatically after some time.
Climate control
Climate control systems ............. 137
Air vents ..................................... 143
Maintenance .............................. 144
Climate control systems
Heating and ventilation system
Controls for:
■ Temperature
■ Air distribution
■ Fan speed
■ Demisting and defrosting
Temperature
red = warm blue = cold
Climate control 137
Heating will not be fully effective until the engine has reached normal operating temperature.
Air distribution
s = to windscreen and front door windows
M = to head area via adjustable air vents
K = to foot well
All combinations are possible.
Fan speed
Adjust the air flow by switching the fan to the desired speed.
Demisting and defrosting
■ Press button V: fan automatically switches to higher speed, the air distribution is directed towards the windscreen.
■ Set temperature control to warmest level.
■ Switch on heated rear window Ü.
■ Open side air vents as required and direct them towards the door windows.
138 Climate control
Air conditioning system
In addition to the heating and ventilation system, the air conditioning system has controls for: n = cooling
4 = air recirculation
Cooling n
Operated with the n button and is functional only when the engine and fan are running.
The air conditioning system cools and dehumidifies (dries) as soon as the outside temperature is slightly above the freezing point. Therefore condensation may form and drip from under the vehicle.
If no cooling or drying is required, switch the cooling system off to save fuel. When the cooling system is switched off, no engine restart will be requested by the climate control system during an Autostop.
Air recirculation system 4
Operated with the 4 button.
9 Warning
The exchange of fresh air is reduced in air recirculation mode.
In operation without cooling the air humidity increases, so the windows may mist up from inside.
The quality of the passenger compartment air deteriorates, which may cause the vehicle occupants to feel drowsy.
In warm and very humid ambient air conditions, the windscreen might mist up from outside, when cold air is directed to it. If windscreen mists up from outside, activate windscreen wiper and deactivate s.
Maximum cooling
Briefly open the windows so that hot air can disperse quickly.
■ Cooling n on.
■ Air circulation system 4 on.
■ Press air distribution switch M.
■ Set temperature control to coldest level.
■ Set fan speed to highest level.
■ Open all vents.
Demisting and defrosting the windows V
■ Press button V: fan automatically switches to higher speed, the air distribution is directed towards the windscreen.
■ Switch cooling n on.
■ Set temperature control to warmest level.
■ Switch on heated rear window Ü.
■ Open side air vents as required and direct them towards the door windows.
Note
If the settings for demisting and defrosting are selected, an Autostop will be inhibited.
If the settings for demisting and defrosting are selected while the engine is in an Autostop, the engine will restart automatically.
Electronic climate control system
The dual zone climate control allows different climatisation temperatures for driver and front passenger side.
Climate control 139
Controls for:
■ Temperature on driver side
■ Air distribution
■ Fan speed
■ Temperature on front passenger side n = cooling
AUTO = automatic mode
4 = manual air recirculation
V = demisting and defrosting
Heated rear window Ü 3 32, Heated
seats ß 3 40, Heated steering wheel
*
The preselected temperature is automatically regulated. In the automatic mode the fan speed and air distribution automatically regulate the air flow.
The system can be manually adapted via the use of air distribution and air flow controls.
140 Climate control
Automatic mode AUTO
The fan speed regulation in automatic mode can be changed in the menu
Settings.
Vehicle personalisation 3 121.
All air vents are actuated automatically in automatic mode. The air vents should therefore always be open.
Temperature preselection
Temperatures can be set to the desired value.
Each change of settings is shown in the Info-Display for a few seconds.
The electronic climate control system is only fully operational when the engine is running.
Basic setting for maximum comfort:
■ Press AUTO button, the air distribution and fan speed are regulated automatically.
■ Open all air vents.
■ Press n to switch on cooling. On some versions cooling is activated automatically by pressing AUTO button.
■ Set the preselected temperatures for driver and front passenger using the left and right rotary knob to
22 °C.
If the minimum temperature is set, the climate control system runs at maximum cooling.
If the maximum temperature is set, the climate control system runs at maximum heating.
Note
If the temperature is reduced 2 °C or more while the engine is in an
Autostop, the engine will restart automatically.
Demisting and defrosting the windows V
■ Press button V.
■ Press cooling button n.
■ Temperature and air distribution are set automatically and the fan runs at high speed.
■ Switch on heated rear window Ü.
■ To return to automatic mode: press button V or AUTO.
Note
If the V button is pressed while the engine is running, an Autostop will be inhibited until the V button is pressed again.
If the V button is pressed while the engine is in an Autostop, the engine will restart automatically.
Manual settings
Climate control system settings can be changed by activating the buttons and rotary knobs as follows.
Changing a setting will deactivate the automatic mode.
Fan speed Z
Climate control 141
Press lower button to decrease or upper button to increase fan speed as shown in the illustration. The fan speed is indicated by the number of segments in the display.
Pressing the lower button longer: fan and cooling are switched off.
Pressing the upper button longer: the fan runs at maximum speed.
To return to automatic mode: Press
AUTO button.
Air distribution s, M, K
Press accordant button for desired adjustment. Activation is indicated by the LED in the button.
s = to windscreen and front door windows.
M = to head area via adjustable air vents
K = to foot well.
All combinations are possible.
Return to automatic air distribution:
Deactivate corresponding setting or press button AUTO.
142 Climate control
Cooling n
Activate or deactivate with the n button.
The air conditioning system cools and dehumidifies (dries) when outside temperature is above a specific level.
Therefore condensation may form and drip from under the vehicle.
If no cooling or drying is required, switch the cooling system off to save fuel. When the cooling system is switched off, no engine restart will be requested by the climate control system during an Autostop.
The display will indicate ACON when cooling is activated or ACOFF when the cooling is deactivated.
Air recirculation mode 4
9 Warning
The exchange of fresh air is reduced in air recirculation mode.
In operation without cooling the air humidity increases, so the windows may mist up from inside.
The quality of the passenger compartment air deteriorates, which may cause the vehicle occupants to feel drowsy.
In warm and very humid ambient air conditions, the windscreen might mist up from outside, when cold air is directed to it. If windscreen mists up from outside, activate windscreen wiper and deactivate s.
Press button 4 once to activate the manual air recirculation mode.
Activation is indicated by the LED in the button.
Basic settings
Some settings can be changed in the menu Settings in the Info-Display.
Vehicle personalisation 3 121.
Climate control 143
Auxiliary heater
Air heater
Quickheat is an electric auxiliary air heater which automatically warms up the passenger compartment more quickly.
Air vents
Adjustable air vents
At least one air vent must be open while the cooling is on.
To open the vent, turn the adjuster wheel towards the bigger W symbol.
Adjust the air amount at the vent outlet by turning the adjuster wheel.
Direct the flow of air by tilting and swivelling the slats.
To close the vent, turn the adjuster wheel towards the smaller W symbol.
9 Warning
Do not attach any objects to the slats of the air vents. Risk of damage and injury in case of an accident.
Fixed air vents
Additional air vents are located beneath the windscreen and door windows and in the foot wells.
144 Climate control
Maintenance
Air intake
The air intake in front of the windscreen in the engine compartment must be kept clear to allow air intake. Remove any leaves, dirt or snow.
Pollen filter
The pollen filter cleans dust, soot, pollen and spores from the air entering the vehicle through the air intake.
Air conditioning regular operation
In order to ensure continuously efficient performance, cooling must be operated for a few minutes once a month, irrespective of the weather and time of year. Operation with cooling is not possible when the outside temperature is too low.
Service
For optimal cooling performance, it is recommended to annually check the climate control system, starting three years after initial vehicle registration, including:
■ Functionality and pressure test
■ Heating functionality
■ Leakage check
■ Check of drive belts
■ Cleaning of condenser and evaporator drainage
■ Performance check
Driving and operating
Driving hints ............................... 145
Starting and operating ............... 146
Engine exhaust .......................... 150
Automatic transmission .............. 152
Manual transmission .................. 155
Brakes ........................................ 156
Ride control systems ................. 159
Driver assistance systems ......... 162
Fuel ............................................ 169
Towing ....................................... 176
Driving hints
Control of the vehicle
Never coast with engine not running (except during
Autostop)
Many systems will not function in this situation (e.g. brake servo unit, power steering). Driving in this manner is a danger to yourself and others. All systems function during an Autostop, but there will be a controlled reduction in power steering assist and vehicle speed is reduced.
Idle boost
If charging of the battery is required due to battery condition, the power output of the generator has to be increased. This will be achieved by an idle boost which may be audible.
On vehicles with Uplevel-Display, a message appears in the Driver
Information Centre.
Driving and operating 145
Pedals
To ensure the pedal travel is uninhibited, there must be no mats in the area of the pedals.
146 Driving and operating
Starting and operating
New vehicle running-in
Do not brake unnecessarily hard for the first few journeys.
During the first drive, smoke may occur because of wax and oil evaporating off the exhaust system.
Park the vehicle in the open for a while after the first drive and avoid inhaling the fumes.
During the running-in period fuel and engine oil consumption may be higher and the cleaning process of the diesel particle filter may take place more often. Autostop may be inhibited to allow for charging the battery.
Ignition switch positions
0 = Ignition off
1 = Steering wheel lock released, ignition off
2 = Ignition on, for diesel engine: preheating
3 = Starting
Retained power off
The following electronic systems can work until the driver's door is opened or at the latest for 10 minutes after the ignition is switched off:
■ Power windows
■ Sunroof
■ Power outlets
Power to the Infotainment system will continue to operate for 30 minutes or until the key is removed from the ignition switch, regardless of whether any door will be opened.
Starting the engine
Manual transmission: operate clutch.
Automatic transmission: operate brake and move the selector lever to
P or N.
Do not operate the accelerator pedal.
Diesel engine: turn the key to position
2 for preheating until control indicator ! extinguishes.
Turn the key briefly to position 3 and release: an automatic procedure operates the starter with a short delay as long as the engine is running, see
Automatic Starter Control.
Before restarting or to switch off the engine, turn the key back to position
0.
During an Autostop, the engine can be started by depressing the clutch pedal.
Starting the vehicle at low temperatures
The start of the engine without additional heaters is possible down to
-25 °С for diesel engines and -30 °C for petrol engines. Required is an engine oil with the correct viscosity, the correct fuel, performed services and a sufficiently charged battery.
With temperatures below -30 °C the automatic transmission need a warming phase of approx.
5 minutes. The selector lever must be in position P.
Automatic Starter Control
This function controls the engine starting procedure. The driver does not have to hold the key in position
3. Once applied, the system will go on starting automatically until the engine is running. Because of the checking procedure, the engine starts running after a short delay.
Driving and operating 147
Possible reasons for a non-starting engine:
■ Clutch pedal not operated (manual transmission)
■ Brake pedal not operated or selector lever not in P or N
(automatic transmission)
■ Timeout occurred
Turbo engine warm-up
Upon start-up, engine available torque may be limited for a short time, especially when the engine temperature is cold. The limitation is to allow the lubrication system to fully protect the engine.
Overrun cut-off
The fuel supply is automatically cut off during overrun, i.e. when the vehicle is driven with a gear engaged but accelerator is released.
148 Driving and operating
Stop-start system
The stop-start system helps to save fuel and to reduce the exhaust emissions. When conditions allow, it switches off the engine as soon as the vehicle is at a low speed or at a standstill, e.g. at a traffic light or in a traffic jam. It starts the engine automatically as soon as the clutch is depressed. A battery sensor ensures that an Autostop is only performed if the battery is sufficiently charged for a restart.
Activation
The stop-start system is available as soon as the engine is started, the vehicle starts-off and the conditions as stated below in this section are fulfilled.
Deactivation
Deactivate the stop-start system manually by pressing the eco button.
The deactivation is indicated when the LED in the button extinguishes.
Autostop
If the vehicle is at a low speed or at a standstill, activate an Autostop as follows:
■ Depress the clutch pedal
■ set the lever in neutral
■ release the clutch pedal
The engine will be switched off while the ignition stays on.
An Autostop is indicated by the needle at the AUTOSTOP position in the tachometer.
During an Autostop, the heating and brake performance will be maintained.
Caution
The steering assist can be reduced during an Autostop.
Conditions for an Autostop
The stop-start system checks if each of the following conditions is fulfilled.
Otherwise an Autostop will be inhibited.
■ The stop-start system is not manually deactivated
■ the bonnet is fully closed
■ the driver's door is closed or the driver's seat belt is fastened
■ the battery is sufficiently charged and in good condition
■ the engine is warmed up
■ the engine coolant temperature is not too high
■ the engine exhaust temperature is not too high, e.g. after driving with high engine load
■ the ambient temperature is not too low
■ the climate control system does not inhibit an Autostop
■ the brake vacuum is sufficient
■ the self-cleaning function of the diesel particle filter is not active
■ the vehicle has moved since the last Autostop
Ambient temperature near to the freezing point can inhibit an Autostop.
Certain settings of the climate control system may inhibit an Autostop. See climate control chapter for more details.
Immediately after motorway driving an Autostop may be inhibited.
Battery discharge protection
To ensure reliable engine restarts, several battery discharge protection features are implemented as part of the stop-start system.
Power saving measures
During an Autostop, several electrical features such as auxiliary electric heater or rear window heating are disabled or switched into a power saving mode. The fan speed of the climate control system is reduced to save power.
Driving and operating 149
Restart of the engine by the driver
Depress the clutch pedal to restart the engine.
The engine start is indicated by the needle at the idle speed position in the tachometer.
If the selector lever is shifted out of neutral before depressing the clutch first, control indicator - illuminates or is shown as a symbol in the Driver
Information Centre.
Restart of the engine by the stop-start system
The selector lever has to be in neutral to enable an automatic restart.
If one of the following conditions occurs during an Autostop, the engine will be restarted automatically by the stop-start system.
■ The stop-start system is manually deactivated
■ the bonnet is opened
150 Driving and operating
■ the driver's seat belt is unfastened and the driver's door is opened
■ the engine temperature is too low
■ the battery is discharged
■ the brake vacuum is not sufficient
■ the vehicle starts to move
■ the climate control system requests an engine start
■ the air conditioning is manually switched on
If the bonnet is not fully closed, a warning message is displayed in the
Driver Information Centre.
If an electrical accessory, e.g.
a portable CD player, is connected to the power outlet, a brief power drop during restart might be noticeable.
Parking
■ Do not park the vehicle on an easily ignitable surface. The high temperature of the exhaust system could ignite the surface.
■ Always apply parking brake. Apply manual parking brake without pressing release button. Apply as firmly as possible on downhill or uphill slopes. Depress the foot brake at the same time to reduce operating force.
■ Switch off the engine and ignition.
Turn the steering wheel until the steering wheel lock engages.
■ If the vehicle is on a level surface or uphill slope, engage first gear or set the selector lever to P before switching off the ignition. On an uphill slope, turn the front wheels away from the kerb.
If the vehicle is on a downhill slope, engage reverse gear or set the selector lever to P before switching off the ignition. Turn the front wheels towards the kerb.
■ Lock the vehicle and activate the anti-theft alarm system.
Note
In the event of an accident with airbag deployment, the engine is turned off automatically if the vehicle comes to a standstill within a certain time.
Engine exhaust
9 Danger
Engine exhaust gases contain poisonous carbon monoxide, which is colourless and odourless and could be fatal if inhaled.
If exhaust gases enter the interior of the vehicle, open the windows.
Have the cause of the fault rectified by a workshop.
Avoid driving with an open load compartment, otherwise exhaust gases could enter the vehicle.
Diesel particle filter
The diesel particle filter system filters harmful soot particles out of the exhaust gases. The system includes a self-cleaning function that runs automatically during driving without any notification. The filter is cleaned by periodically burning off the soot particles at high temperature. This process takes place automatically under set driving conditions and may
take up to 25 minutes. Typically it needs between 7 and 12 minutes.
Autostop is not available and fuel consumption may be higher during this period. The emission of smells and smoke during this process is normal.
Under certain driving conditions, e.g.
short distances, the system cannot clean itself automatically.
If the cleaning of the filter is required and if previous driving conditions did not enable automatic cleaning, it will be indicated by control indicator %.
Simultaneously Diesel partic. filter is full continue driving or warning code 55 appears in the Driver
Information Centre.
% illuminates when diesel particle filter is full. Start cleaning process as soon as possible.
% flashes when diesel particle filter has reached the maximum filling level. Start cleaning process immediately to avoid damage to the engine.
Cleaning process
To activate cleaning process, continue driving, keep engine speed above 2000 revolutions per minute.
Shift down if necessary. Diesel particle filter cleaning is then started.
If g illuminates additionally, cleaning is not possible, seek the assistance of a workshop.
Caution
If the cleaning process is interrupted, there is a risk of provoking severe engine damage.
Driving and operating 151
Cleaning takes place quickest at high engine speeds and loads.
The control indicator % extinguishes as soon as the self-cleaning operation is complete.
Catalytic converter
The catalytic converter reduces the amount of harmful substances in the exhaust gases.
Caution
Fuel grades other than those listed
damage the catalytic converter or electronic components.
Unburnt petrol will overheat and damage the catalytic converter.
Therefore avoid excessive use of the starter, running the fuel tank dry and starting the engine by pushing or towing.
In the event of misfiring, uneven engine running, a reduction in engine performance or other unusual problems, have the cause of the fault
152 Driving and operating
rectified by a workshop as soon as possible. In an emergency, driving can be continued for a short period, keeping vehicle speed and engine speed low.
Automatic transmission
The automatic transmission permits automatic gearshifting (automatic mode) or manual gearshifting
(manual mode).
Transmission display
Selector lever
The mode or selected gear is shown in the transmission display.
P = park position, wheels are locked, engage only when the vehicle is stationary and the parking brake is applied
R = reverse gear, engage only when the vehicle is stationary
N = neutral
D = automatic mode with all gears
The selector lever is locked in P and can only be moved when the ignition is on and the brake pedal is applied.
Without brake pedal applied, the control indicator j illuminates.
If the selector lever is not in P when the ignition is switched off, the control indicators j and P flash.
To engage P or R, press the release button.
The engine can only be started with the lever in position P or N. When position N is selected, press the brake pedal or apply the parking brake before starting.
Do not accelerate while engaging a gear. Never depress the accelerator pedal and brake pedal at the same time.
When a gear is engaged, the vehicle slowly begins to creep when the brake is released.
Engine braking
To utilise the engine braking effect, select a lower gear in good time when driving downhill, see manual mode.
Rocking the vehicle
Rocking the vehicle is only permissible if the vehicle is stuck in sand, mud or snow. Move the selector lever between D and R in a repeat pattern. Do not race the engine and avoid sudden acceleration.
Parking
Apply the parking brake and engage
P.
The ignition key can only be removed when the selector lever is in position
P.
Driving and operating
Manual mode
153
Move selector lever out of position D towards the left and then forwards or backwards.
< = Shift to a higher gear.
] = Shift to a lower gear.
If a higher gear is selected when vehicle speed is too low, or a lower gear when vehicle speed is too high, the shift is not executed. This can cause a message in the
Driver-Info-Display.
154 Driving and operating
In manual mode no automatic shifting to a higher gear takes place at high engine revolutions.
Electronic driving programmes
■ Following a cold start, the operating temperature programme increases engine speed to quickly bring the catalytic converter to the required temperature.
■ The automatic neutral shift function automatically shifts to idling when the vehicle is stopped with a forward gear engaged and the brake pedal is pressed.
■ When SPORT mode is engaged, the vehicle shifts at higher engine speeds (unless cruise control is
■ Special programmes automatically adapt the shifting points when driving up inclines or down hills.
Kickdown
If the accelerator pedal is pressed down completely in automatic mode, the transmission shifts to a lower gear depending on engine speed.
Fault
In the event of a fault, g illuminates.
Additionally a code number or a vehicle message is displayed in the
Driver Information Centre. Vehicle
The transmission no longer shifts automatically. Continued travel is possible with manual shifting.
Only the highest gear is available.
Depending on the fault, 2nd gear may also be available in manual mode.
Shift only when vehicle is at a standstill.
Have the cause of the fault remedied by a workshop.
Interruption of power supply
In the event of an interruption of power supply, the selector lever cannot be moved out of the P position. The ignition key cannot be removed from the ignition switch.
If the battery is discharged, start the
vehicle using jump leads 3 219.
If the battery is not the cause of the fault, release the selector lever.
1. Apply the parking brake.
2. Release the selector lever trim from the centre console at the front, fold it upwards and rotate it to the left.
Manual transmission
Driving and operating 155
Caution
It is not advisable to drive with the hand resting on the selector lever.
3. Insert a screwdriver into the opening as far as it will go and move the selector lever out of P or
N. If P or N is engaged again, the selector lever will be locked in position again. Have the cause of the power supply interruption remedied by a workshop.
4. Mount the selector lever trim onto the centre console and refit.
To engage reverse, with the vehicle stationary wait 3 seconds after depressing the clutch pedal and then press the release button on the selector lever and engage the gear.
If the gear does not engage, set the lever to neutral, release the clutch pedal and depress again; then repeat gear selection.
Do not grind the clutch unnecessarily.
When operating, depress the clutch pedal completely. Do not use the pedal as a foot rest.
156 Driving and operating
Brakes
The brake system comprises two independent brake circuits.
If a brake circuit fails, the vehicle can still be braked using the other brake circuit. However, braking effect is achieved only when the brake pedal is depressed firmly. Considerably more force is needed for this. The braking distance is extended. Seek the assistance of a workshop before continuing your journey.
When the engine is not running, the support of the brake servo unit disappears once the brake pedal has been depressed once or twice.
Braking effect is not reduced, but braking requires significantly greater force. It is especially important to bear this in mind when being towed.
Antilock brake system
Antilock brake system (ABS) prevents the wheels from locking.
ABS starts to regulate brake pressure as soon as a wheel shows a tendency to lock. The vehicle remains steerable, even during hard braking.
ABS control is made apparent through a pulse in the brake pedal and the noise of the regulation process.
For optimum braking, keep the brake pedal fully depressed throughout the braking process, despite the fact that the pedal is pulsating. Do not reduce the pressure on the pedal.
After starting off the system performs a self-test which may be audible.
Adaptive brake light
During full braking, all three brake lights flash for the duration of ABS control.
Fault
9 Warning
If there is a fault in the ABS, the wheels may be liable to lock due to braking that is heavier than normal. The advantages of ABS are no longer available. During hard braking, the vehicle can no longer be steered and may swerve.
Have the cause of the fault remedied by a workshop.
Parking brake
Manual parking brake
Electrical parking brake
Always apply parking brake firmly without operating the release button, and apply as firmly as possible on a downhill or uphill slope.
To release the parking brake, pull the lever up slightly, press the release button and fully lower the lever.
To reduce the operating forces of the parking brake, depress the foot brake at the same time.
Applying when vehicle is stationary
Pull switch m, the electrical parking brake operates automatically with an adequate force. For maximum force, e.g. parking with trailer or on inclines, pull switch m twice.
The electrical parking brake is applied when control indicator m lights up
The electrical parking brake can always be activated, even if the ignition is off.
Driving and operating 157
Do not operate electrical parking brake system too often without engine running because this will discharge the battery.
Before leaving the vehicle, check the electrical parking brake status.
Releasing
Switch on ignition. Keep brake pedal depressed and then push switch m.
Drive away function
Depressing clutch pedal (manual transmission) or engaging drive gear
(automatic transmission) and then depressing the accelerator pedal releases the electrical parking brake automatically. This is not possible when the switch is pulled at the same time.
This function also helps driving away on inclines.
Aggressive drive away may reduce life time of wear parts.
158 Driving and operating
Dynamic braking when vehicle is moving
When the vehicle is moving and the switch m is kept pulled, the electrical parking brake system will decelerate the vehicle, but will not apply statically.
As soon as the switch m is released, dynamic braking will be stopped.
Fault
Failure mode of electrical parking brake is indicated by control indicator j and by a code number or a vehicle message which is displayed in the
Driver Information Centre. Vehicle
Apply electrical parking brake: pull and hold the switch m for more than
5 seconds. If control indicator m illuminates, electrical parking brake is applied.
Release electrical parking brake: push and hold the switch m for more than 2 seconds. If control indicator m extinguishes, electrical parking brake is released.
Control indicator m flashes: electrical parking brake is not fully applied or released. When continuously flashing, release electrical parking brake and retry applying.
Brake assist
If the brake pedal is depressed quickly and forcefully, maximum brake force is automatically applied
(full braking).
Maintain steady pressure on the brake pedal for as long as full braking is required. Maximum brake force is automatically reduced when the brake pedal is released.
Hill start assist
The system helps prevent unintended movement when driving away on inclines.
When releasing the foot brake after stopping on an incline, the brakes remain on for a further two seconds.
The brakes release automatically as soon as the vehicle begins to accelerate.
The hill start assist is not active during an Autostop.
Ride control systems
Traction Control system
The Traction Control system (TC) is a component of the Electronic
Stability Control.
TC improves driving stability when necessary, regardless of the type of road surface or tyre grip, by preventing the drive wheels from spinning.
As soon as the drive wheels starts to spin, engine output is reduced and the wheel spinning the most is braked individually. This considerably improves the driving stability of the vehicle on slippery road surfaces.
TC is operational as soon as the control indicator b extinguishes.
When TC is active b flashes.
9 Warning
Do not let this special safety feature tempt you into taking risks when driving.
Adapt speed to the road conditions.
Deactivation
TC can be switched off when spinning of drive wheels is required: press button b briefly.
Control indicator k illuminates.
Driving and operating 159
TC is reactivated by pressing the b button again.
TC is also reactivated the next time the ignition is switched on.
Electronic Stability Control
Electronic Stability Control (ESC) improves driving stability when necessary, regardless of the type of road surface or tyre grip. It also prevents the drive wheels from spinning.
As soon as the vehicle starts to swerve (understeer/oversteer), engine output is reduced and the wheels are braked individually. This considerably improves the driving stability of the vehicle on slippery road surfaces.
ESC is operational as soon as the control indicator b extinguishes.
When ESC is active b flashes.
160 Driving and operating
9 Warning
Do not let this special safety feature tempt you into taking risks when driving.
Adapt speed to the road conditions.
Deactivation
For very high-performance driving
ESC can be deactivated: hold button b depressed for approx. 7 seconds.
Control indicator n illuminates.
ESC is reactivated by pressing the b button again. If the TC system was previously disabled, both TC and
ESC are reactivated.
ESC is also reactivated the next time the ignition is switched on.
Interactive driving system
Flex Ride
Flex Ride driving system allows the driver to select between three driving modes:
■ SPORT mode: press button
SPORT, LED illuminates.
■ TOUR mode: press button TOUR,
LED illuminates.
■ Normal mode: both buttons
SPORT and TOUR are not pressed, no LED illuminates.
Deactivate SPORT mode and TOUR mode by pressing corresponding button once more.
In each driving mode Flex Ride networks the following electronic systems:
■ Continuous Damping Control.
■ Accelerator Pedal Control.
■ Steering Control.
■ Automatic transmission.
SPORT mode
The settings of the systems are adapted to a sportier driving style:
■ Damping of shock absorbers reacts more stiffly to provide better contact with the road surface.
■ The engine reacts more quickly to the accelerator pedal.
■ Steering support is reduced.
■ Shift points of automatic transmission occur later.
■ With SPORT mode activated, the illumination of main instruments changes from white to red.
TOUR mode
The settings of the systems are adapted to a comfort driving style:
■ Damping of shock absorbers reacts more softly.
■ Accelerator pedal reacts with standard settings.
■ Steering support is in standard mode.
■ Shift points of automatic transmission occur in a comfort mode.
■ Illumination of main instruments is white.
Normal mode
All settings of the systems are adapted to standard values.
Drive mode control
Within each manual selected driving mode SPORT, TOUR or Normal, the
Drive Mode Control (DMC) detects and analyses continuously the real driving characteristic, responses by the driver, and the active dynamic state of the vehicle. If necessary, the control unit of DMC automatically changes the settings within the selected driving mode or, when recognising greater variations, the driving mode is changed for the length of variation.
If, for example, Normal mode is selected and DMC detects a sporty driving behaviour, DMC changes several settings of the Normal mode
Driving and operating 161
into sporty settings. The DMC changes to SPORT mode in case of very sporty driving behaviour.
If, for example, TOUR mode is selected and whilst driving on a winding road a sudden hard brake is necessary, DMC will detect the dynamic vehicle condition and changes the settings for suspension to SPORT mode to increase vehicle stability.
When the driving characteristic or the dynamic vehicle state returns to former state, DMC will change the settings to the preselected driving mode.
Personalised settings in the
Sport mode
The driver can select the functions of the SPORT mode when SPORT button is pressed. These settings can be changed in the menu Settings in the Info-Display. Vehicle
162 Driving and operating
Driver assistance systems
9 Warning
Driver assistance systems are developed to support the driver and not to replace his attention.
The driver accepts fully responsibility when driving the vehicle.
When using driver assistance systems, take always care on the traffic situation.
Cruise control
The cruise control can store and maintain speeds of approx. 20 to
120 mph. Deviations from the stored speeds may occur when driving uphill or downhill.
For safety reasons the cruise control cannot be activated until the foot brake has been operated once.
Activating in first gear is not possible.
Do not use the cruise control if it is not advisable to maintain a constant speed.
With automatic transmission, only activate cruise control in automatic mode.
Switching on
Press button m, control indicator m in instrument cluster illuminates white.
Activation
Accelerate to the desired speed and turn thumb wheel to SET/-, the current speed is stored and maintained. Control indicator m illuminates green. Accelerator pedal can be released.
Vehicle speed can be increased by depressing the accelerator pedal.
When the accelerator pedal is released, the previously stored speed is resumed.
Cruise control remains activated while gear is changed.
Increase speed
With cruise control active, hold thumb wheel turned to RES/+ or briefly turn to RES/+ repeatedly: speed increases continuously or in small increments.
Alternatively accelerate to the desired speed and store by turning to SET/-.
Reduce speed
With cruise control active, hold thumb wheel turned to SET/- or briefly turn to SET/- repeatedly: speed decreases continuously or in small increments.
Deactivation
Press button y, control indicator m in instrument cluster illuminates white.
Cruise control is deactivated. Last used set speed is stored in memory for later speed resume.
Automatic deactivation:
■ vehicle speed below approx.
20 mph,
■ vehicle speed above approx.
125 mph,
■ the brake pedal is depressed,
■ the clutch pedal is depressed for a few seconds,
■ selector lever in N,
■ engine speed in a very low range,
■ the Traction Control system or
Electronic Stability Control is operating.
Resume stored speed
Turn thumb wheel to RES/+ at a speed above 20 mph. The stored speed will be obtained.
Switching off
Press button m, control indicator m in instrument cluster extinguishes. The stored speed is deleted.
Switching off the ignition also deletes the stored speed.
Parking assist
The parking assist makes parking easier by measuring the distance between the vehicle and obstacles, and giving acoustic signals.
Driving and operating 163
The warning chime regarding unfastened seat belts has priority
over any other acoustic signal 3 117.
Even when using the parking assist, the driver remains fully responsible for the parking manoeuvre.
The system consists of four ultrasonic parking sensors in the rear bumper. If the vehicle is equipped with a front parking assist the system consists of four additional ultrasonic parking sensors in the front bumper.
The system uses two different frequencies for the front and rear sensors, respectively, each with a different sound.
164
Activation
Driving and operating
When reverse gear is engaged, the system is activated automatically.
The front parking assist can also be activated at a low speed by pressing the r button.
An illuminated LED in the parking assist button indicates that the system is ready to operate.
Depending on which of the sensors are closer to an obstacle, you will hear the buzzing sound of the respective sensors. The interval between the sounds becomes shorter as the vehicle gets closer to the obstacle.
When the distance is less than
30 cm, the buzzing is continuous.
Depending on the version, the distance to a front obstacle is indicated in the Driver Information
Display by changing segments.
If the r button is pressed once within an ignition cycle, the front parking assist is always reactivated when the vehicle speed goes below a certain value.
Deactivation
Deactivate the system by pressing the r button.
The LED in the button will go out and
Park Assist Off will be displayed in the
Driver Information Centre.
The system is deactivated automatically at a certain speed.
Fault
In the event of a fault in the system, r illuminates or a vehicle message is displayed in the Driver Information
Centre.
Additionally, r illuminates or a vehicle message is displayed in the
Driver Information Centre if a malfunction of the system due to temporary conditions like snow covered sensors is detected.
Important hints for using the parking assist systems
9 Warning
Under certain circumstances, various reflective surfaces on objects or clothing as well as external noise sources may cause the system to fail to detect obstacles.
Special attention has to be paid to low obstacles which can damage the lower part of the bumper. If such obstacles leave the detection area of the sensors during approach of the vehicle, a continuous warning tone will sound.
Caution
Performance of the sensor can be reduced when sensors are covered, e.g. by ice or snow.
Performance of the parking assist systems can be reduced due to heavy loading.
Special conditions apply if there are taller vehicles involved (e.g.
off-road vehicles, mini vans, vans). Object identification in the upper part of these vehicles cannot be guaranteed.
Objects with a very small reflection cross section, like objects of narrow size or soft materials, may not be detected by the system.
Parking assist will not avoid a collision with objects which are out of the detection range of the sensors.
Driving and operating 165
Note
The parking assist system automatically detects factory-fitted towing equipment. It is deactivated when the connector is plugged in.
The sensor may detect a nonexisting object (echo disturbance) caused by external acoustical or mechanic disturbances.
Traffic sign assistant
Functionality
The traffic sign assistant system detects designated traffic signs via a front camera and displays them in the Driver Information Centre.
Traffic signs, which will be detected, are:
■ speed limit
■ no passing
■ end of speed limit
■ end of no passing
Speed limit signs are displayed in the
Driver Information Centre until the next speed limit sign or end of speed limit is detected.
No passing signs have priority above speed limits.
Combinations of both signs in the display are possible.
166 Driving and operating
An exclamation mark in a frame indicates that there is an supplementary sign detected which cannot be recognised by the system.
The system is active at an indicated speed above 9 mph and is active up to a speed of 124 mph depending on the lighting conditions. At night the system is active up to a speed of
99 mph.
As soon as the speed becomes slower than 34 mph the display will be reset and the content of the traffic sign page will be cleared. The next recognized speed indication will be displayed.
Display indication
Traffic signs are displayed on the page Traffic sign detection in the Trip/
Fuel Information Menu, chosen via the adjuster wheel on the turn signal
When another function on the Driver
Information Centre menu was selected and then Traffic sign detection page is chosen again, the last recognized traffic sign will be displayed.
If the system is deactivated, the content of the traffic sign page is cleared, indicated by the following symbol:
The content of the traffic sign page is also cleared during driving by pushing the SET/CLR button on the turn signal lever.
Pop-up function
Driving and operating 167
Speed limits and no passing signs are displayed as pop-up on each page of the menu.
The pop-up function can be deactivated on the traffic sign page by pressing the SET/CLR button on the turn signal lever.
Once setting page is displayed, select
Off to deactivate pop-up function.
Reactivate by selecting On. When switching on the ignition, pop-up function is deactivated.
Pop-up indication is displayed for approx. 8 seconds in the Driver
Information Centre.
168 Driving and operating
Fault
The traffic sign assistant system may not operate correctly when:
■ the area of the windscreen, where the front camera is located, is not clean
■ traffic signs are completely or partially covered or difficult to discern
■ there are adverse environmental conditions like heavy rain, snow, direct sunlight or shadows. In this case No Traffic Sign Detection due to Weather is indicated on the display
■ traffic signs are incorrectly mounted or damaged
■ traffic signs do not comply with the
Wiener Übereinkommen über
Straßenverkehrszeichen (Vienna
Convention on traffic signs)
Caution
The system is intended to help the driver within a defined speed range to discern certain traffic signs. Do not ignore traffic signs which are not displayed by the system.
The system does not discern any other than the conventional traffic signs that might give or end a speed limit.
Do not let this special feature tempt you into taking risks when driving.
Always adapt speed to the road conditions.
The driver assistance systems do not relieve the driver from full responsibility for vehicle operation.
Lane departure warning
The lane departure warning system observes the lane markings between which the vehicle is driving via a front camera. The system detects lane changes and warns the driver in the event of an unintended lane change via visual and acoustic signals.
Criteria for the detection of an unintended lane change are:
■ no operation of turn signals
■ no brake pedal operation
■ no active accelerator operation or speeding-up
■ no active steering
If the driver is active, no warning will be issued.
Activation
The lane departure warning system is activated by pressing the ) button.
The illuminated LED in the button indicates that the system is switched on. When the control indicator ) in the instrument cluster illuminates green, the system is ready to operate.
The system is only operable at vehicle speeds above 35 mph and if lane markings are available.
When the system recognizes an unintended lane change, the control indicator ) changes to yellow and flashes. Simultaneously a chime sound is activated.
Deactivation
The system is deactivated by pressing ) button, the LED in the button extinguishes.
At speeds below 35 mph the system is inoperable.
Fault
The lane departure warning system may not operate properly when:
■ the windscreen is not clean
■ there are adverse environmental conditions like heavy rain, snow, direct sunlight or shadows
The system can not operate when no lane marking is detected.
Driving and operating 169
Fuel
Fuel for petrol engines
Only use unleaded fuel that complies with EN 228.
Usage of fuel with quality, not complying to the Technical
Regulations in effect (Decree № 118 of 27.02.2008 with amendments of
30.12.2008 № 1076) can lead to engine damage and loss of all warranty obligations.
Equivalent standardised fuels with an ethanol content of max. 10 % by volume may be used. In this case only use fuel that complies with
E DIN 51626-1.
Use fuel with the recommended
octane rating 3 234. Use of fuel with
too low an octane rating can reduce engine power and torque and slightly increases fuel consumption.
170 Driving and operating
Caution
Use of fuel that does not comply to
EN 228 or similar can lead to deposits or engine damage and loss of warranty.
Caution
Use of fuel with too low an octane rating could lead to uncontrolled combustion and engine damage.
Fuel for diesel engines
Only use diesel fuel that complies with EN 590.
Usage of fuel with quality, not complying to the Technical
Regulations in effect (Decree № 118 of 27.02.2008 with amendments of
30.12.2008 № 1076) can lead to engine damage and loss of all warranty obligations.
In countries outside the European
Union use Euro-Diesel fuel with a sulfur concentration below 50 ppm.
Caution
Use of fuel that does not comply to
EN 590 or similar can lead to engine powerloss, increased wear or engine damage and loss of warranty.
Do not use marine diesel oils, heating oils, Aquazole and similar dieselwater emulsions. Diesel fuels must not be diluted with fuels for petrol engines.
Fuel for liquid gas operation
Liquid gas is known as LPG
(Liquefied Petroleum Gas) or under its French name GPL (Gaz de Pétrole
Liquéfié). LPG is also known as
Autogas.
LPG consists mainly of propane and butane. The octane rating is between
105 and 115, depending on the butane proportion. LPG is stored liquid at around 5 - 10 bar pressure.
The boiling point depends on the pressure and mixing ratio. At ambient pressure, it is between -42 °C (pure propane) and -0.5 °C (pure butane).
Caution
The system works at an ambient temperature of approx. -8 °C to
100 °C.
Full function of the LPG system can only be guaranteed with liquid gas which complies with the minimum requirements of DIN EN 589.
Fuel selector
Driving and operating 171
Pressing the LPG button switches between petrol and liquid gas operation as soon as the required parameters (coolant temperature, gas temperature and minimum engine speed) have been reached.
The requirements are usually fulfilled after around 60 seconds (depending on exterior temperature) and the first firm press on the accelerator. The
LED status shows the current operating mode.
1 off = petrol operation
1 illuminates = liquid gas
1 flashes operation
= no switching is possible, one type of fuel is empty
As soon as the liquid gas tanks are empty, petrol operation is automatically engaged until the ignition is switched off.
Every six months, run the petrol tank down until control indicator i illuminates, then refuel. This helps maintain fuel quality and system function for petrol operation.
Fill the tank completely at regular intervals to prevent corrosion in the tank.
Faults and remedies
If gas mode is not possible, check the following:
■ Is there enough liquid gas present?
■ Is there enough petrol present for starting?
Due to extreme temperatures in combination with the gas composition, it may take slightly longer before the system switches from petrol to gas mode.
In extreme situations, the system may also switch back to petrol mode if the minimum requirements are not fulfilled.
Seek the assistance of a workshop in the event of all other faults.
Caution
Repairs and adjustments may only be made by trained specialists in order to maintain the safety and warranty on the LPG system.
Liquid gas is given a particular odour
(odorised) so that any leaks can be detected easily.
9 Warning
If you smell gas in the vehicle or in the immediate vicinity, switch to petrol mode immediately. No smoking. No naked flames or ignition sources.
If possible, close the manual shut-off valve on the multivalve. The multivalve is located on the liquid gas tank in the load compartment, underneath the rear floor cover.
172 Driving and operating
Refuelling
Turn the thumb wheel clockwise.
If no further gas odour is perceptible when the manual shut-off valve is closed, the vehicle can be used in petrol mode. If the gas odour persists, do not start the engine. Have the cause of the fault remedied by a workshop.
When using underground car parks, follow the instructions of the operator and local laws.
Note
In the event of an accident, switch off the ignition and lights. Close the manual shut-off valve on multivalve.
9 Danger
Before refuelling, switch off engine and any external heaters with combustion chambers. Switch off any mobile phones.
Follow the operating and safety instructions of the filling station when refuelling.
9 Danger
Fuel is flammable and explosive.
No smoking. No naked flames or sparks.
If you can smell fuel in your vehicle, have the cause of this remedied immediately by a workshop.
Caution
In case of misfuelling, do not switch on ignition.
Fuel filler flap is located at right rear side of vehicle.
Driving and operating 173
Fuel filler cap
Only use genuine fuel filler caps.
Diesel-engined vehicles have special fuel filler caps.
Liquid gas refuelling
Follow the operating and safety instructions of the filling station when refuelling.
The filling valve for the liquid gas is behind the fuel filler cap.
The fuel filler flap can only be opened if the vehicle is unlocked. Release the fuel filler flap by pushing the flap.
To open, turn the cap slowly to the left.
The fuel filler cap can be retained in the bracket on the fuel filler flap.
For refuelling, fully insert the pump nozzle and switch it on.
After automatic cut-off, it can be topped up with max. two doses of fuel.
Caution
Wipe off any overflowing fuel immediately.
To close, turn the fuel filler cap to the right until it clicks.
Close the flap and let engage.
Unscrew protective cap from the filler neck.
174 Driving and operating
Fit the required adapter.
ACME Adapter: Screw the nut of the filling nozzle onto the adapter. Press locking lever on filler nozzle down.
DISH (Italy) filler neck: Place the filler nozzle into the adapter. Press locking lever on filler nozzle down.
Bayonet filler neck: Place filler nozzle on the adapter and turn to the left or right through one quarter turn. Pull locking lever of filler nozzle fully.
EURO filler neck: Press the filler nozzle onto the adapter until it engages.
Press the button of the liquid gas supply point. The filling system stops or begins to run slowly when 80% ofthe tank volume is reached
(maximum fill level).
Release button on filling system and the filling process stops. Release the locking lever and remove the filler nozzle. A small quantity of liquid gas can escape.
Remove adapter and stow in vehicle.
Fit protective cap to prevent the penetration of foreign bodies into the filler opening and the system.
9 Warning
Due to the system design, an escape of liquid gas after releasing the locking lever is unavoidable. Avoid inhaling.
9 Warning
The liquid gas tank may only be filled to 80% for safety reasons.
The multivalve on the liquid gas tank automatically limits the fill quantity. If a larger quantity is added, we recommend not exposing the vehicle to the sun until the excess amount has been used up.
Filling adapter
As filling systems are not standardised, different adapters are required which are available from
Vauxhall Distributors and from
Vauxhall Authorised Repairers.
ACME adapter: Belgium, Germany,
Ireland, Luxembourg, Switzerland
EURO adapter: Spain
Bayonet adapter: Netherlands,
Norway, Spain, United Kingdom
DISH (Italy) adapter: Bosnia-
Herzegovina, Bulgaria, Denmark,
Estonia, France, Greece, Italy,
Driving and operating 175
Croatia, Latvia, Lithuania,
Macedonia, Austria, Poland,
Portugal, Romania, Sweden,
Switzerland, Serbia, Slovakia,
Slovenia, Czech Republic, Turkey,
Ukraine, Hungary
Fuel consumption - CO
2
Emissions
-
Petrol
The fuel consumption (combined) of the model Vauxhall Astra is within a range of 38 to 72 mpg.
The CO
2
emission (combined) is within a range of 99 to 177 g/km.
For the values specific for your vehicle, refer to the EEC Certificate of
Conformity provided with your vehicle or other national registration documents.
Liquid gas
The gas consumption (combined) of the model Vauxhall Astra was not available at time of printing.
176 Driving and operating
The CO
2
emission (combined) was not available at time of printing.
General information
The official fuel consumption and specific CO
2
emission figures quoted relate to the EU base model with standard equipment.
Fuel consumption data and CO
2 emission data are determined according to regulation R (EC) No.
715/2007 (in the version respectively applicable), taking into consideration the vehicle weight in running order, as specified by the regulation.
The figures are provided only for the purpose of comparison between different vehicle variants and must not be taken as a guarantee for the actual fuel consumption of a particular vehicle. Additional equipment may result in slightly higher results than the stated consumption and CO
2
figures.
Furthermore, fuel consumption is dependent on personal driving style as well as road and traffic conditions.
Towing
General information
Only use towing equipment that has been approved for your vehicle.
Entrust retrofitting of towing equipment to a workshop. It may be necessary to make changes that affect the cooling system, heat shields or other equipment.
Fitting of towing equipment could cover the opening of the towing eye.
If this is the case use the coupling ball bar for towing. Always keep the coupling ball bar in the vehicle.
Installation dimensions of factory-
fitted towing equipment 3 253.
Driving characteristics and towing tips
Before attaching a trailer, lubricate the coupling ball. However, do not do so if a stabiliser, which acts on the coupling ball, is being used to reduce snaking movements.
For trailers with low driving stability and caravan trailers with a permitted gross vehicle weight of more than
1300 kg the use of a stabiliser is strongly recommended when driving above 50 mph.
If the trailer starts snaking, drive more slowly, do not attempt to correct the steering and brake sharply if necessary.
When driving downhill, drive in the same gear as if driving uphill and drive at a similar speed.
Adjust tyre pressure to the value
specified for full load 3 247.
Trailer towing
Trailer loads
The permissible trailer loads are vehicle and engine-dependent maximum values which must not be exceeded. The actual trailer load is the difference between the actual gross weight of the trailer and the actual coupling socket load with the trailer coupled.
The permissible trailer loads are specified in the vehicle documents. In general, they are valid for gradients up to max. 12 %.
The permitted trailer load applies up to the specified incline and up to an altitude of 1000 metres above sea level. Since engine power decreases as altitude increases due to the air becoming thinner, therefore reducing climbing ability, the permissible gross train weight also decreases by 10 % for every 1000 metres of additional altitude. The gross train weight does not have to be reduced when driving on roads with slight inclines (less than
8 %, e.g. motorways).
The permissible gross train weight must not be exceeded. This weight is specified on the identification plate
Vertical coupling load
The vertical coupling load is the load exerted by the trailer on the coupling ball. It can be varied by changing the weight distribution when loading the trailer.
The maximum permissible vertical coupling load (75 kg) is specified on the towing equipment identification plate and in the vehicle documents.
Always aim for the maximum load, especially in the case of heavy trailers. The vertical coupling load should never fall below 25 kg.
Rear axle load
When the trailer is coupled and the towing vehicle fully loaded, the permissible rear axle load (see identification plate or vehicle documents) may be exceeded by
60 kg, the gross vehicle weight rating may be exceeded by 60 kg. If the permissible rear axle load is exceeded, a maximum speed of
60 mph applies.
Towing equipment
Caution
When operating without a trailer, remove the coupling ball bar.
Driving and operating
Stowage of coupling ball bar
177
The bag with the coupling ball bar is stowed in the rear stowage compartment on the floor.
Place the strap through the lashing eye, wrap around twice and tighten the strap to secure the bag.
178 Driving and operating
Fitting the coupling ball bar
Disengage and fold down the socket.
Remove the sealing plug from the opening for the coupling ball bar and stow it.
Checking the tensioning of the coupling ball bar
Otherwise, the coupling ball bar must be tensioned before being inserted:
■ Unlock coupling ball bar by turning key to position c.
Press fastenings inward and remove cover.
■ Red marking on rotary knob must point towards green marking on coupling ball bar.
■ The gap between the rotary knob and the coupling ball bar must be approx. 6 mm.
■ The key must be in position c.
■ Pull out rotary knob and turn clockwise as far as it will go.
Inserting the coupling ball bar Eye for break-away stopping cable
Insert the tensioned coupling ball bar in the opening and push firmly upwards until it audibly engages.
The rotary handle snaps back into its original position resting against the coupling ball bar without a gap.
9 Warning
Do not touch rotary handle during insertion.
Lock the coupling ball bar by turning the key to position e. Remove the key and close the protective flap.
Attach breakaway stopping cable to eye.
Check that the coupling ball bar is correctly installed
■ Green marking on rotary knob must point towards green marking on coupling ball bar.
■ There must be no gap between the rotary handle and the coupling ball bar.
Driving and operating 179
■ The coupling ball bar must be firmly engaged in the opening.
■ The coupling ball bar must be locked and the key removed.
9 Warning
Towing a trailer is permitted only when a coupling ball bar is fitted correctly. If the coupling ball bar does not engage correctly, seek the assistance of a workshop.
Dismounting the coupling ball bar
180 Driving and operating
Open the protective flap and turn the key to position c to unlock the coupling ball bar.
Pull out rotary handle and turn clockwise as far as it will go. Pull out coupling ball bar downwards.
Insert sealing plug in opening. Fold away socket.
Replace cover.
Trailer stability assist
If the system detects snaking movements, engine power is reduced and the vehicle/trailer combination is selectively braked until the snaking ceases. While system is working keep steering wheel as still as possible.
Trailer stability assist (TSA) is a function of the Electronic Stability
Vehicle care
General Information ................... 181
Vehicle checks ........................... 182
Bulb replacement ....................... 189
Electrical system ........................ 198
Vehicle tools .............................. 205
Wheels and tyres ....................... 205
Jump starting ............................. 219
Towing ....................................... 220
Appearance care ....................... 222
General Information
Accessories and vehicle modifications
We recommend the use of genuine parts and accessories and factory approved parts specific for your vehicle type. We cannot assess or guarantee reliability of other products
- even if they have a regulatory or otherwise granted approval.
Do not make any modifications to the electrical system, e.g. changes of electronic control units (chip tuning).
Caution
When transporting the vehicle on a train or on a recovery vehicle, the mud flaps might be damaged.
Vehicle care 181
Vehicle storage
Storage for a long period of time
If the vehicle is to be stored for several months:
■ Wash and wax the vehicle.
■ Have the wax in the engine compartment and underbody checked.
■ Clean and preserve the rubber seals.
■ Fill up fuel tank completely.
■ Change the engine oil.
■ Drain the washer fluid reservoir.
■ Check the coolant antifreeze and corrosion protection.
■ Adjust tyre pressure to the value specified for full load.
■ Park the vehicle in a dry, well ventilated place. Engage first or reverse gear or set selector lever to
P. Prevent the vehicle from rolling.
■ Do not apply the parking brake.
■ Open the bonnet, close all doors and lock the vehicle.
182 Vehicle care
■ Disconnect the clamp from the negative terminal of the vehicle battery. Beware that all systems are not functional, e.g. anti-theft alarm system.
Putting back into operation
When the vehicle is to be put back into operation:
■ Connect the clamp to the negative terminal of the vehicle battery.
Activate the electronics of the power windows.
■ Check tyre pressure.
■ Fill up the washer fluid reservoir.
■ Check the engine oil level.
■ Check the coolant level.
■ Fit the number plate if necessary.
End-of-life vehicle recovery
Information on end-of-life vehicle recovery centres and the recycling of end-of-life vehicles is available on our website. Only entrust this work to an authorised recycling centre.
Gas vehicles must be recycled by a service centre authorised for gas vehicles.
Vehicle checks
Performing work
9 Warning
Only perform engine compartment checks when the ignition is off.
The cooling fan may start operating even if the ignition is off.
9 Danger
The ignition system and Xenon headlights use extremely high voltage. Do not touch.
Bonnet
Opening
Pull the release lever and return it to its original position.
Push the safety catch to the right and open the bonnet.
Vehicle care 183
If the bonnet is opened during an
Autostop, the engine will be restarted automatically for safety reasons.
Closing
Before closing the bonnet, press the support into the holder.
Lower the bonnet and allow it to drop into the catch. Check that the bonnet is engaged.
Engine oil
Check the engine oil level manually on a regular basis to prevent damage to the engine. Ensure that the correct specification of oil is used.
Recommended fluids and lubricants
Check with the vehicle on a level surface. The engine must be at operating temperature and switched off for at least 5 minutes.
Pull out the dipstick, wipe it clean, insert it to the stop on the handle, pull out and read the engine oil level.
Secure the bonnet support.
184 Vehicle care
Caution
It is the owner's responsibility to maintain the proper level of an appropriate quality oil in the engine.
Insert dipstick to the stop on the handle and make half a turn.
Different dipsticks are used depending on engine variant.
When the engine oil level has dropped to the MIN mark, top up engine oil.
We recommend the use of the same grade of engine oil that was used at last change.
The engine oil level must not exceed the MAX mark on the dipstick.
Caution
Overfilled engine oil must be drained or suctioned out.
Fit the cap on straight and tighten it.
Engine coolant
The coolant provides freeze protection down to approx. -28 °C. In northern countries with very low temperatures the factory filled coolant provides frost protection down to approx. -37°C.
Caution
Only use approved antifreeze.
Coolant level
Caution
Too low a coolant level can cause engine damage.
If the cooling system is cold, the coolant level should be above the filling line mark. Top up if the level is low.
Vehicle care
Washer fluid
185
9 Warning
Allow the engine to cool before opening the cap. Carefully open the cap, relieving the pressure slowly.
To top up use a 1:1 mixture of released coolant concentrate mixed with clean tap water. If no coolant concentrate is available, use clean tap water. Install the cap tightly. Have the coolant concentration checked and have the cause of the coolant loss remedied by a workshop.
Fill with clean water mixed with a suitable quantity of windscreen washer fluid which contains antifreeze. For the correct mixing ratio refer to the washer fluid container.
Caution
Only washer fluid with a sufficient antifreeze concentration provides protection at low temperatures or a sudden drop in temperature.
186 Vehicle care
Brakes
In the event of minimum thickness of the brake lining, a squealing noise sounds during braking.
Continued driving is possible but have the brake lining replaced as soon as possible.
Once new brake linings are installed, do not brake unnecessarily hard for the first few journeys.
Brake fluid
9 Warning
Brake fluid is poisonous and corrosive. Avoid contact with eyes, skin, fabrics and painted surfaces.
Battery
The vehicle battery is maintenancefree provided that the driving profile allows sufficient charging of the battery. Short-distance-driving and frequent engine starts can discharge the battery. Avoid the use of unnecessary electrical consumers.
The brake fluid level must be between the MIN and MAX marks.
When topping up, ensure maximum cleanliness as contamination of the brake fluid can lead to brake system malfunctions. Have the cause of the loss of brake fluid remedied by a workshop.
Only use high-performance brake fluid approved for the vehicle. Brake
Batteries do not belong in household waste. They must be disposed of at an appropriate recycling collection point.
Laying up the vehicle for more than
4 weeks can lead to battery discharge. Disconnect the clamp from the negative terminal of the vehicle battery.
Ensure the ignition is switched off before connecting or disconnecting the vehicle battery.
The anti-theft alarm siren must be deactivated as follows: Switch the ignition on then off, disconnect the vehicle's battery within 15 seconds.
Battery discharge protection 3 135.
Replacing the battery
Note
Any deviation from the instructions given in this paragraph may lead to a temporary deactivation of the stopstart system.
When the battery is being replaced, please ensure that there are no open ventilation holes in the vicinity of the positive terminal. If a ventilation hole is open in this area, it must be closed off with a dummy cap, and the ventilation in the vicinity of the negative terminal must be opened.
Only use batteries that allow the fuse box to be mounted above the battery.
In vehicles with stop-start system, ensure to have the AGM (Absorptive
Glass Mat) battery replaced with an
AGM battery again.
An AGM battery can be identified by the label on the battery. We recommend the use of an original
Vauxhall battery.
Note
Using an AGM battery different from the original Vauxhall battery might result in a lower performance of the stop-start system.
We recommend that you have the battery replaced by a workshop.
Vehicle care 187
Charging the battery
9 Warning
On vehicles with stop-start system, ensure that the charging potential does not exceed 14.6
volts when using a battery charger. Otherwise the battery might be damaged.
Warning label
188 Vehicle care
Meaning of symbols:
■ No sparks, naked flames or smoking.
■ Always shield eyes. Explosive gases can cause blindness or injury.
■ Keep the battery out of reach of children.
■ The battery contains sulfuric acid which could cause blindness or serious burn injuries.
■ See the Owner’s Manual for further information.
■ Explosive gas may be present in the vicinity of the battery.
Diesel fuel system bleeding
If the tank has been run dry, the diesel fuel system must be bled. Switch on the ignition three times for
15 seconds at a time. Then start the engine for a maximum of
40 seconds. Repeat this process after no less than 5 seconds. If the engine fails to start, seek the assistance of a workshop.
Wiper blade replacement
Lift the wiper arm until it stays in the raised position, press button to disengage the wiper blade and remove.
Attach the wiper blade slightly angled to the wiper arm and push until it engages.
Lower wiper arm carefully.
Wiper blade on the rear window
Lift wiper arm. Disengage wiper blade as shown in illustration and remove.
Attach the wiper blade slightly angled to the wiper arm and push until it engages.
Lower wiper arm carefully.
Bulb replacement
Switch off the ignition and switch off the relevant switch or close the doors.
Only hold a new bulb at the base! Do not touch the bulb glass with bare hands.
Use only the same bulb type for replacement.
Replace headlight bulbs from within the engine compartment.
Halogen headlights
Vehicle care 189
Headlights have separate systems for low beam 1 (outer bulbs) and high beam 2 (inner bulbs).
Low beam
1. Rotate the cap 1 anticlockwise and remove it.
190 Vehicle care
2. Rotate the bulb holder anticlockwise to disengage.
Withdraw the bulb holder from the reflector.
3. Detach the bulb from the bulb holder and replace the bulb.
4. Insert the bulb holder, engaging the two lugs into the reflector and rotate clockwise to secure.
5. Fit the cap and rotate clockwise.
High beam
3. Detach the bulb from the bulb holder and replace the bulb.
4. Insert the bulb holder, engaging the two lugs into the reflector and rotate clockwise to secure.
5. Fit the cap and rotate clockwise.
Sidelights/Daytime running light
1. Rotate the cap 2 anticlockwise and remove it.
2. Rotate the bulb holder anticlockwise to disengage.
Withdraw the bulb holder from the reflector.
1. Rotate the cap anticlockwise and remove it. Use the screwdriver to rotate the cap.
Vehicle care 191
3. Remove the bulb from the socket and replace the bulb.
4. Insert the bulb holder into the reflector. Fit the cap and rotate clockwise.
Front turn signal
2. Press latches together and withdraw the bulb holder from the reflector.
The bulbs are accessible from beneath the vehicle.
1. Disengage the spring clip and then swivel it backwards.
2. Pull the bulb holder with bulb out of the reflector.
192 Vehicle care
3. Disengage the bulb holder from the plug connector by pressing the retaining lug.
4. Remove and replace the bulb holder with bulb.
5. Attach the plug connector.
6. Insert the bulb holder into the reflector.
7. Swivel the spring clip forwards and engage.
Xenon headlights
9 Danger
Xenon headlights work under extremely high electrical voltage.
Do not touch. Have bulbs replaced by a workshop.
Fog lights
The bulbs are accessible from beneath the vehicle.
1. Turn the bulb holder anticlockwise and remove it from the reflector.
2. Disengage the bulb holder from the plug connector by pressing the retaining lug.
3. Remove and replace the bulb holder with bulb.
4. Attach the plug connector.
5. Insert the bulb holder into the reflector.
6. Turn the bulb holder clockwise and engage.
Tail lights
Saloon/Hatchback
2. Unscrew the plastic securing nut from the inside by hand.
Vehicle care 193
1. Release the cover and remove it.
3. Carefully withdraw the light assembly from retaining pins and remove. Make sure that the cable duct remains in position.
4. Detach the cable from the retainer.
5. Detach the wiring plug from the bulb carrier.
6. Unscrew the three screws with a coin and remove the bulb carrier.
7. Remove and replace the bulb.
194 Vehicle care
Tail lights (1)
Brake light (2)
Turn signal light (3)
8. Insert the bulb carrier into the tail light assembly and screw into place. Connect the wiring plug and press the cable into the retainer. Fit light assembly onto retaining pins and tighten the securing nut. Close the cover and engage.
9. Switch on the ignition, operate and check all lights.
Tail lights in the tailgate
1. Open the tailgate and remove the three covers.
2. Unscrew the three screws and remove.
3. Remove the tail light assembly.
Make sure that the cable duct remains in position.
4. Press the retaining lug and remove the bulb carrier from the tail light assembly.
5. To replace the tail light (1), remove and replace the bulb
To replace the rear fog light (2), push the bulb slightly into the socket, rotate anticlockwise, remove and replace the bulb.
6. Insert the bulb carrier into the tail light assembly. Install the tail light assembly in the tailgate and tighten the screws. Attach the three covers.
7. Switch on the ignition, operate and check all lights.
For replacing the tail light bulb and reverse light bulb on the right side of the tailgate, proceed in the same way.
Sports tourer
2. Remove cover.
Vehicle care 195
4. Carefully remove tail light assembly. Take care that the cable duct remains in position.
Detach wiring plug from bulb holder.
1. On left-hand side, fold down the blind and remove.
3. Unscrew two plastic securing nuts from the inside by hand.
5. Remove and replace the bulb.
Tail lights (1 + 2)
Turn signal light (3)
Brake light (4)
6. Connect the wiring plug and press the cable into the retainer. Install tail light assembly in tailgate and tighten securing nuts. Close cover.
196 Vehicle care
Tail light in the tailgate
When assembling press the blind into the rubber grommets to reach full retention force.
7. Switch on the ignition, operate and check all lights.
1. Open the tailgate and remove the covers.
2. Unscrew the screws and remove.
3. Remove the tail light assembly.
4. Remove and replace the bulb.
5. Install the tail light assembly in the tailgate and tighten the screws.
Attach the covers.
6. Switch on the ignition, operate and check all lights.
Rear fog light / reverse light in the tailgate
1. Remove cover.
2. Remove and replace the bulb of rear fog light.
3. Close cover.
For replacing reverse light bulb on the right side of the tailgate, proceed in the same way.
Side turn signal lights
Have bulbs replaced by a workshop.
Number plate light
Vehicle care 197
2. Remove the bulb holder downwards, taking care not to pull on the cable.
3. Disengage the retaining lug and remove the bulb holder from the wiring plug.
4. Remove and replace the bulb holder with bulb.
5. Connect the wiring plug to the bulb holder.
6. Push the bulb holder into the housing and close the cover.
1. Insert screwdriver in recess of the cover, press to the side and release spring. Remove cover.
198 Vehicle care
Interior lights
Courtesy light, reading lights
Have bulbs replaced by a workshop.
Load compartment light
Have bulbs replaced by a workshop.
Instrument panel illumination
Have bulbs replaced by a workshop.
Electrical system
Fuses
Data on the replacement fuse must match the data on the defective fuse.
There are three fuse boxes in the vehicle:
■ in the front left of the engine compartment,
■ in left-hand drive vehicles, in the interior behind the storage compartment, or, in right-hand drive vehicles, behind the glovebox,
■ behind a cover on the left side of the load compartment.
Before replacing a fuse, turn off the respective switch and the ignition.
A blown fuse can be recognized by its melted wire. Do not replace the fuse until the cause of the fault has been remedied.
Some functions are protected by several fuses.
Fuses may also be inserted without existence of a function.
Fuse extractor
A fuse extractor may be located in the fuse box in the engine compartment.
Vehicle care 199
Engine compartment fuse box
Place the fuse extractor on the various types of fuse from the top or side, and withdraw fuse.
The fuse box is in the front left of the engine compartment.
Disengage the cover and fold it upwards until it stops. Remove the cover vertically upwards.
200 Vehicle care
No. Circuit
1 Engine control module
2 Lambda probe
3 Fuel injection, ignition system
4 Fuel injection, ignition system
5 –
6 Mirror heating
7 Fan control
8 Lambda probe, engine
9 Rear window sensor
10 Battery sensor
11 Trunk release
12 Adaptive forward lighting module
13 –
14 Rear window wiper
15 Engine control module
16 Starter
No. Circuit
17 Transmission control module
18 Heated rear window
19 Front power windows
20 Rear power windows
21 ABS
22 Left high beam (Halogen)
23 Headlamp washer system
24 Right low beam (Xenon)
25 Left low beam (Xenon)
26 Fog lights
27 Diesel fuel heating
28 –
29 Electrical parking brake
30 ABS
31 –
32 Airbag
33 Adaptive forward lighting
No. Circuit
34 –
35 Power windows
36 –
37 Canister vent solenoid
38 Vacuum pump
39 Fuel system control module
40 Windscreen washer, Rear window washer system
41 Right high beam (Halogen)
42 Radiator fan
43 Windscreen wiper
44 –
45 Radiator fan
46 –
47 Horn
48 Radiator fan
49 Fuel pump
No. Circuit
50 Headlamp levelling
51 Air shutter
52 Auxiliary heater, diesel engine
53 Transmission control module,
Engine control module
54 Wiring monitoring
After having changed defective fuses close the fuse box cover and press until it engages.
If the fuse box cover is not closed correctly, malfunction may occur.
Vehicle care 201
Instrument panel fuse box
In left-hand drive vehicles, the fuse box is behind the storage compartment in the instrument panel.
Open the compartment and push it to the left to unlock. Fold the compartment down and remove it.
202 Vehicle care
In right-hand drive vehicles, the fuse box is located behind a cover in the glovebox. Open the glovebox, then open the cover and fold it down.
No. Circuit
1 Displays
2 Exterior lights
3 Exterior lights
4 Radio
5 Infotainment system, instrument
6 Power outlet front
7 Power outlet rear seat
8 Left low beam
9 Right low beam
10 Door locks
11 Interior fan
12 –
13 –
14 Diagnostic connector
15 Airbag
16 –
No. Circuit
17 Air conditioning system
18 Prefuse: radio, Infotainment, displays
19 Brake lights, tail lights, interior lights
20 –
21 –
22 Ignition switch
23 Body control unit
24 Body control unit
25 –
26 Power outlet load compartment
(if no load compartment fuse box) (Sports tourer only)
Load compartment fuse box
5-door hatchback
The fuse box is on the left side of the load compartment behind a cover.
Remove the cover.
Sports tourer
The fuse box is on the left side of the load compartment behind a cover.
Fold down the blind and remove.
Remove the cover.
Vehicle care
Fuse assignments
203
204 Vehicle care
No. Circuit
1 Trailer module
2 Trailer outlet
3 Parking assist
4 –
5 –
6 –
7 –
8 Anti-theft alarm system
9 –
10 –
11 Trailer module, Trailer socket
12 –
13 Trailer outlet
14 –
15 –
16 –
17 –
No. Circuit
18 –
19 Steering wheel heating
20 Sunroof
21 Seat heating
22 –
23 –
24 –
25 –
26 –
27 –
28 –
29 –
30 –
31 Amplifier, Subwoofer
32 Active damping system, Lane departure warning
When assembling press the blind into the rubber grommets to reach full retention force.
Vehicle tools
Tools
Vehicles with tyre repair kit
The tools and tyre repair kit are in a storage compartment below the floor cover in the load compartment.
Vehicles with spare wheel, variant 1
The jack, the tools and a strap for securing a damaged wheel are in a storage compartment below the spare wheel in the load compartment.
Vehicles with spare wheel, variant 2
The jack and the tools are in a storage compartment below the spare wheel in the load compartment. The wheel wrench and the extension bar for securing a damaged wheel are in a tool bag located in the spare wheel
Vehicle care 205
Wheels and tyres
Tyre condition, wheel condition
Drive over edges slowly and at right angles if possible. Driving over sharp edges can cause tyre and wheel damage. Do not trap tyres on the kerb when parking.
Regularly check the wheels for damage. Seek the assistance of a workshop in the event of damage or unusual wear.
Winter tyres
Winter tyres improve driving safety at temperatures below 7 °C and should therefore be fitted on all wheels.
Tyres of size 205/55 R 16,
205/60 R 16, 205/65 R 16,
215/50 R 17, 225/45 R 17,
225/50 R 17 are permitted as winter tyres.
206 Vehicle care
Tyres of size 235/40 R 19 and
235/45 R 18 and 225/45 R 18 not be used as winter tyres.
1) must
Tyres of size 215/60 R 16 2) must not be used as winter tyres on engines
A14XEL, A14XER, A14NET,
A16XER, A13DTE, A17DTR and
A17DTJ.
In accordance with country-specific regulations, affix the speed sticker in the driver's field of view.
Speed code letter:
Q = up to 100 mph
S = up to 112 mph
T = up to 118 mph
H = up to 130 mph
V = up to 150 mph
W = up to 168 mph
Tyre designations
E.g. 215/60 R 16 95 H
215 = Tyre width, mm
60 = Cross-section ratio (tyre height to tyre width), %
R = Belt type: Radial
RF = Type: RunFlat
16 = Wheel diameter, inches
95 = Load index e.g. 95 is equivalent to 690 kg
H = Speed code letter
1)
2)
Tyre pressure
Check the pressure of cold tyres at least every 14 days and before any long journey. Do not forget the spare wheel. This also applies to vehicles with tyre pressure monitoring system.
Unscrew the valve cap.
Tyre pressure 3 247 and on the label
on the front left door frame.
The tyre pressure data refers to cold tyres. It applies to summer and winter tyres.
Always inflate the spare tyre to the pressure specified for full load.
The ECO tyre pressure serves to achieve the smallest amount of fuel consumption possible.
Not permitted as winter tyres on engines A14NET and A16XER with limitation steering angle, continuously variable real time damping chassis and/or sport chassis.
Permitted as winter tyres on engines A16LET and A20DTH. Not permitted as winter tyres on engines A16LET and
A20DTH with limitation steering angle and/or sport chassis.
Vehicle care 207
Incorrect tyre pressures will impair safety, vehicle handling, comfort and fuel economy and will increase tyre wear.
9 Warning
If the pressure is too low, this can result in considerable tyre warmup and internal damage, leading to tread separation and even to tyre blow-out at high speeds.
If the tyre pressure shall be reduced or increased on a vehicle with tyre pressure monitoring system, switch off ignition.
Tyre pressure monitoring system
The tyre pressure monitoring system checks the pressure of all four wheels once a minute when vehicle speed exceeds a certain limit.
All wheels must be equipped with pressure sensors and the tyres must have the prescribed pressure.
The current tyre pressures can be shown in the Vehicle Information
Menu in the Driver Information
Centre.
The menu can be selected by the buttons on the turn signal lever.
Press the MENU button to select the
Vehicle Information Menu.
Turn the adjuster wheel to select the tyre pressure monitoring system.
System status and small pressure differences are displayed by a warning message with the corresponding tyre flashing in the
Driver Information Centre.
Furthermore considerable pressure differences between the tyres on one axle are displayed by a warning message in the Driver Information
Centre.
Major pressure differences are indicated additionally by the control indicator w.
208 Vehicle care
If the tyre pressure shall be reduced or increased, switch off ignition.
If a complete set of wheels without sensors is mounted (e.g. four winter tyres), a message is displayed in the
Driver Information Centre. The tyre pressure monitoring system is not operational. Retrofitting of sensors is possible.
A spare wheel or temporary spare wheel is not equipped with pressure sensors. The tyre pressure monitoring system is not operational for these wheels. Control indicator w illuminates. For the further three wheels the system remains operational.
The use of commercially available liquid tyre repair kits can impair the function of the system. Factory approved repair kits can be used.
External high-power radio equipment could disrupt the tyre pressure monitoring system.
The tyre pressure monitoring system valve cores and sealing rings must be replaced each time the tyres are changed.
Adaptive threshold function
The tyre pressure monitoring system automatically detects if the vehicle is driven with a tyre pressure appropriate for a load of up to
3 people or for a full load.
If the tyre pressure shall be reduced, switch off ignition before reducing.
Auto learn function
After changing wheels the vehicle has to be stationary for approx.
20 minutes, before the system recalculates. The following relearn process takes up to 10 minutes of driving with a minimum speed of
12 mph. In this case $ can be displayed or pressure values can swap in the Driver Information Centre.
If problems occur during the relearn process a warning message is displayed in the Driver Information
Centre.
Temperature compensation
Cold tyres decrease the tyre pressure, warm tyres increase the tyre pressure. The tyre pressure monitoring system considers this effect for the warning messages.
The tyre pressure value displayed in the Driver Information Centre shows the actual tyre pressure. Therefore it is important to check tyre pressure with cold tyres.
Tread depth
Check tread depth at regular intervals.
Tyres should be replaced for safety reasons at a tread depth of 2-3 mm
(4 mm for winter tyres).
For safety reasons it is recommended that the tread depth of the tyres on one axle should not vary by more than
2 mm.
The legally permissible minimum tread depth (1.6 mm) has been reached when the tread has worn down as far as one of the tread wear indicators (TWI). Their position is indicated by markings on the sidewall.
If there is more wear at the front than the rear, swap round front wheels and rear wheels periodically. Ensure that the direction of rotation of the wheels is the same as before.
Tyres age, even if they are not used.
We recommend tyre replacement every 6 years.
Changing tyre and wheel size
If tyres of a different size than those fitted at the factory are used, it may be necessary to reprogramme the speedometer as well as the nominal tyre pressure and make other vehicle modifications.
After converting to a different tyre size, have the label with tyre pressures replaced.
9 Warning
Use of unsuitable tyres or wheels may lead to accidents and will invalidate the vehicle type approval.
Wheel covers
Wheel covers and tyres that are factory approved for the respective vehicle and comply with all of the relevant wheel and tyre combination requirements must be used.
Vehicle care 209
If the wheel covers and tyres used are not factory approved, the tyres must not have a rim protection ridge.
Wheel covers must not impair brake cooling.
9 Warning
Use of unsuitable tyres or wheel covers could lead to sudden pressure loss and thereby accidents.
Tyre chains
210 Vehicle care
Tyre chains are only permitted on the front wheels.
Always use fine mesh chains that add no more than 10 mm to the tyre tread and the inboard sides (including chain lock).
9 Warning
Damage may lead to tyre blowout.
Tyre chains are only permitted on tyres of size 205/55 R 16,
205/60 R 16, 215/50 R 17 and
225/45 R 17.
Tyre chains are not permitted on tyres of size 205/65 R 16, 215/60 R 16,
225/45 R 18, 225/50 R 17,
235/40 R 19, 235/45 R 18.
The use of tyre chains is not permitted on the temporary spare wheel.
Tyre repair kit
Minor damage to the tyre tread can be repaired with the tyre repair kit.
Do not remove foreign bodies from the tyres.
Tyre damage exceeding 4 mm or that is at tyre's sidewall cannot be repaired with the tyre repair kit.
9 Warning
Do not drive faster than 50 mph.
Do not use for a lengthy period.
Steering and handling may be affected.
If you have a flat tyre:
Apply the parking brake and engage first gear, reverse gear or P.
The tyre repair kit is in a compartment under the floor cover in the load compartment or in the underseat
1. Take the tyre repair kit from the compartment.
2. Remove the compressor.
3. Remove the electrical connection cable and air hose from the stowage compartments on the underside of the compressor.
Vehicle care 211
4. Screw the compressor air hose to the connection on the sealant bottle.
5. Fit the sealant bottle into the retainer on the compressor.
Set the compressor near the tyre in such a way that the sealant bottle is upright.
6. Unscrew valve cap from defective tyre.
7. Screw the filler hose to the tyre valve.
8. The switch on the compressor must be set to J.
9. Connect the compressor plug to the power outlet or cigarette lighter socket.
To avoid discharging the battery, we recommend running the engine.
10. Set the rocker switch on the compressor to I. The tyre is filled with sealant.
11. The compressor pressure gauge briefly indicates up to 6 bar whilst the sealant bottle is emptying
(approx. 30 seconds). Then the pressure starts to drop.
12. All of the sealant is pumped into the tyre. Then the tyre is inflated.
13. The prescribed tyre pressure should be obtained within
10 minutes. Tyre pressure
3 247. When the correct pressure
is obtained, switch off the compressor.
212 Vehicle care
If the prescribed tyre pressure is not obtained within 10 minutes, remove the tyre repair kit. Move the vehicle one tyre rotation.
Reattach the tyre repair kit and continue the filling procedure for
10 minutes. If the prescribed tyre pressure is still not obtained, the tyre is too badly damaged. Seek the assistance of a workshop.
Drain excess tyre pressure with the button over the pressure indicator.
Do not run the compressor longer than 10 minutes.
14. Detach the tyre repair kit. Push catch on bracket to remove sealant bottle from bracket. Screw the tyre inflation hose to the free connection of the sealant bottle.
This prevents sealant from escaping. Stow tyre repair kit in load compartment.
15. Remove any excess sealant using a cloth.
16. Take the label indicating maximum permitted speed from the sealant bottle and affix in the driver's field of view.
17. Continue driving immediately so that sealant is evenly distributed in the tyre. After driving approx.
6 miles (but no more than
10 minutes), stop and check tyre pressure. Screw compressor air hose directly onto tyre valve and compressor when doing this.
If tyre pressure is more than
1.3 bar, set it to the correct value.
Repeat the procedure until there is no more loss of pressure.
If the tyre pressure has fallen below 1.3 bar, the vehicle must not be used. Seek the assistance of a workshop.
18. Stow away tyre repair kit in load compartment.
Note
The driving characteristics of the repaired tyre are severely affected, therefore have this tyre replaced.
If unusual noise is heard or the compressor becomes hot, turn compressor off for at least
30 minutes.
The built-in safety valve opens at a pressure of 102 psi.
Note the expiry date of the kit. After this date its sealing capability is no longer guaranteed. Pay attention to storage information on sealant bottle.
Replace the used sealant bottle.
Dispose of the bottle as prescribed by applicable laws.
The compressor and sealant can be used from approx. -30 °C.
The adapters supplied can be used to pump up other items e.g.
footballs, air mattresses, inflatable dinghies etc. They are located on the underside of the compressor. To remove, screw on compressor air hose and withdraw adapter.
Wheel changing
Some vehicles are equipped with a tyre repair kit instead of a spare
Make the following preparations and observe the following information:
■ Park the vehicle on a level, firm and non-skid surface. The front wheels must be in the straight-ahead position.
■ Apply the parking brake and engage first gear, reverse gear or
P.
■ Remove the spare wheel 3 216.
■ Never change more than one wheel at once.
■ Use the jack only to change wheels in case of puncture, not for seasonal winter or summer tyre change.
■ If the ground on which the vehicle is standing is soft, a solid board
(max. 1 cm thick) should be placed under the jack.
■ No people or animals may be in the vehicle when it is jacked-up.
Vehicle care 213
■ Never crawl under a jacked-up vehicle.
■ Do not start the vehicle when it is raised on the jack.
■ Clean wheel nuts and thread with a clean cloth before mounting the wheel.
9 Warning
Do not grease wheel bolt, wheel nut and wheel nut cone.
1. Disengage wheel nut caps with a screwdriver and remove. Pull off
214 Vehicle care
the wheel cover with the hook.
Alloy wheels: Disengage wheel nut caps with a screwdriver and remove. To protect the wheel, place a soft cloth between the screwdriver and the alloy wheel.
2. Variant 1:
3. Ensure the jack is correctly positioned under the relevant vehicle jacking point.
4. Variant 1:
Install the wheel wrench ensuring that it locates securely and loosen each wheel nut by half a turn.
Variant 2:
Fold out the wheel wrench and install ensuring that it locates securely and loosen each wheel nut by half a turn.
Set the jack to the necessary height. Position it directly below the jacking point in a manner that prevents it from slipping.
Attach jack handle and with the jack correctly aligned rotate handle until wheel is clear of the ground.
Variant 2:
Set the jack to the necessary height. Position it directly below the jacking point in a manner that prevents it from slipping.
Vehicle care 215
Attach wheel wrench and with the jack correctly aligned rotate wheel wrench until wheel is clear of the ground.
5. Unscrew the wheel nuts.
6. Change the wheel.
7. Screw on the wheel nuts.
8. Lower vehicle.
9. Install the wheel wrench ensuring that it locates securely and tighten each nut in a crosswise sequence. Tightening torque is
140 Nm.
10. Align the valve hole in the wheel cover with the tyre valve before installing.
Install wheel nut caps.
11. Stow the replaced wheel 3 216
12. Check the tyre pressure of the installed tyre and the wheel nut torque as soon as possible.
Have the defective tyre renewed or repaired.
216 Vehicle care
Jacking position for lifting platform
Caution
The use of a spare wheel that is smaller than the other wheels or in combination with winter tyres could affect driveability. Have the defective tyre replaced as soon as possible.
Rear arm position of the lifting platform centrically under the recess of the sill.
Front arm position of the lifting platform at the underbody.
Spare wheel
Some vehicles are equipped with a tyre repair kit instead of a spare wheel.
The spare wheel can be classified as a temporary spare wheel depending on the size compared to the other mounted wheels and country regulations.
The spare wheel has a steel rim.
The spare wheel is located in the load compartment beneath the floor covering. It is secured with a wing nut.
The spare wheel well is not designed for all permissible tyre sizes. If a wheel wider than the spare wheel has to be stowed in the load
compartment after having changed wheels, it needs to be secured with a strap, or, in the Sports tourer, with a long bolt.
Stowing a damaged wheel in the load compartment, 5-door hatchback
A damaged wheel must be stowed in the load compartment and secured
with a strap. Vehicle tools 3 205
1. Position the wheel close to one sidewall of the load compartment.
3. Place the hook end of the strap through the loop and pull it until the strap is fastened securely to the lashing eye.
2. Place the loop end of the strap through the front lashing eye on the appropriate side.
Vehicle care 217
■ Turn the wing nut anticlockwise and remove temporary spare wheel and tool box.
4. Insert the strap through the spokes of the wheel as shown in the illustration.
5. Mount the hook to the rear lashing eye.
6. Tighten the strap and secure it using the buckle.
Storing a damaged wheel in the spare wheel well, Sports tourer
Use the extension bar placed in the
tool bag. Vehicle tools 3 205.
■ Install the hexagon key of the wheel wrench ensuring that it locates securely on the bolt.
■ Turn the wheel wrench anticlockwise to loosen the bolt.
Remove the bolt.
■ Take the long bolt from the tool box and screw it in hand-tight using the wheel wrench.
■ Store the tool box and the damaged wheel and secure it by turning the wing nut clockwise.
218 Vehicle care
The floor cover can be placed on the projecting wheel.
Replace the long bolt before fitting the spare wheel in the well after renewing or repairing the defective wheel.
9 Warning
Storing a jack, a wheel or other equipment in the load compartment could cause injury if they are not fixed properly. During a sudden stop or a collision, loose equipment could strike someone.
Store jack and tools always in the respective storage compartments and secure them by fixing.
Place the damaged wheel always in the load compartment secured by the strap or in the spare wheel well secured by the wing nut.
Temporary spare wheel
Caution
The use of a spare wheel that is smaller than the other wheels or in combination with winter tyres could affect driveability. Have the defective tyre replaced as soon as possible.
Only mount one temporary spare wheel. Do not drive faster than
50 mph. Take curves slowly. Do not use for a long period of time.
If your vehicle gets a flat tyre on the rear while towing another vehicle, mount the temporary spare wheel in the front and the full tyre in the rear.
Directional tyres
Fit directional tyres such that they roll in the direction of travel. The rolling direction is indicated by a symbol
(e.g. an arrow) on the sidewall.
The following applies to tyres fitted opposing the rolling direction:
■ Driveability may be affected. Have the defective tyre renewed or repaired as soon as possible.
■ Drive particularly carefully on wet and snow-covered road surfaces.
Jump starting
Do not start with quick charger.
A vehicle with a discharged battery can be started using jump leads and the battery of another vehicle.
9 Warning
Be extremely careful when starting with jump leads. Any deviation from the following instructions can lead to injuries or damage caused by battery explosion or damage to the electrical systems of both vehicles.
9 Warning
Avoid contact of the battery with eyes, skin, fabrics and painted surfaces. The fluid contains sulphuric acid which can cause injuries and damage in the event of direct contact.
■ Never expose the battery to naked flames or sparks.
■ A discharged battery can already freeze at a temperature of 0 °C.
Defrost the frozen battery before connecting jump leads.
■ Wear eye protection and protective clothing when handling a battery.
■ Use a booster battery with the same voltage (12 Volts). Its capacity (Ah) must not be much less than that of the discharged battery.
■ Use jump leads with insulated terminals and a cross section of at least 16 mm 2 (25 mm 2 for diesel engines).
■ Do not disconnect the discharged battery from the vehicle.
■ Switch off all unnecessary electrical consumers.
■ Do not lean over the battery during jump starting.
■ Do not allow the terminals of one lead to touch those of the other lead.
Vehicle care 219
■ The vehicles must not come into contact with each other during the jump starting process.
■ Apply the parking brake, transmission in neutral, automatic transmission in P.
Lead connection order:
1. Connect the red lead to the positive terminal of the booster battery.
2. Connect the other end of the red lead to the positive terminal of the discharged battery.
220 Vehicle care
3. Connect the black lead to the negative terminal of the booster battery.
4. Connect the other end of the black lead to a vehicle grounding point, such as the engine block or an engine mounting bolt. Connect as far away from the discharged battery as possible, however at least 60 cm.
Route the leads so that they cannot catch on rotating parts in the engine compartment.
To start the engine:
1. Start the engine of the vehicle providing the jump.
2. After 5 minutes, start the other engine. Start attempts should be made for no longer than
15 seconds at an interval of
1 minute.
3. Allow both engines to idle for approx. 3 minutes with the leads connected.
4. Switch on electrical consumers
(e.g. headlights, heated rear window) of the vehicle receiving the jump start.
5. Reverse above sequence exactly when removing leads.
Towing
Towing the vehicle
Insert a screwdriver in the slot at the lower bend of the cap. Release the cap by carefully moving the screwdriver downwards.
The towing eye is stowed with the
Vehicle care
Towing another vehicle
221
Screw in the towing eye as far as it will go until it stops in a horizontal position.
Attach a tow rope – or better still a tow rod – to the towing eye.
The towing eye must only be used for towing and not for recovering the vehicle.
Switch on ignition to release steering wheel lock and to permit operation of brake lights, horn and windscreen wiper.
Transmission in neutral.
Switch on the hazard warning flashers on both vehicles.
Caution
Drive slowly. Do not drive jerkily.
Excessive tractive force can damage the vehicle.
When the engine is not running, considerably more force is needed to brake and steer.
To prevent the entry of exhaust gases from the towing vehicle, switch on the air recirculation and close the windows.
Vehicles with automatic transmission:
The vehicle must be towed facing forwards, not faster than 50 mph nor further than 60 miles. In all other cases and when the transmission is defective, the front axle must be raised off the ground.
Seek the assistance of a workshop.
After towing, unscrew the towing eye.
Insert cap at the bottom and close.
Disengage the cap at the bottom and remove downwards.
The towing eye is stowed with the
222 Vehicle care
Screw in the towing eye as far as it will go until it stops in a horizontal position.
The lashing eye at the rear underneath the vehicle must never be used as a towing eye.
Attach a tow rope – or even better a tow bar – to the towing eye.
The towing eye must only be used for towing and not for recovering a vehicle.
Caution
Drive slowly. Do not drive jerkily.
Excessive tractive force can damage the vehicle.
After towing, unscrew the towing eye.
Insert cap at the bottom and engage.
Appearance care
Exterior care
Locks
The locks are lubricated at the factory using a high quality lock cylinder grease. Use de-icing agent only when absolutely necessary, as this has a degreasing effect and impairs lock function. After using de-icing agent, have the locks regreased by a workshop.
Washing
The paintwork of your vehicle is exposed to environmental influences.
Wash and wax your vehicle regularly.
When using automatic vehicle washes, select a programme that includes waxing.
Bird droppings, dead insects, resin, pollen and the like should be cleaned off immediately, as they contain aggressive constituents which can cause paint damage.
If using a vehicle wash, comply with the vehicle wash manufacturer's instructions. The windscreen wiper and rear window wiper must be switched off. Remove antenna and external accessories such as roof racks etc.
If you wash your vehicle by hand, make sure that the insides of the wheel housings are also thoroughly rinsed out.
Clean edges and folds on opened doors and the bonnet as well as the areas they cover.
Caution
Always use a cleaning agent with a pH value of 4 to 9.
Do not use cleaning agents on hot surfaces.
Have the door hinges of all doors greased by a workshop.
Do not clean the engine compartment with a steam-jet or high-pressure jet cleaner.
Thoroughly rinse and leather-off the vehicle. Rinse leather frequently. Use separate leathers for painted and glass surfaces: remnants of wax on the windows will impair vision.
Exterior lights
Headlight and other light covers are made of plastic. Do not use any abrasive or caustic agents, do not use an ice scraper, and do not clean them dry.
Polishing and waxing
Wax the vehicle regularly (at the latest when water no longer beads).
Otherwise, the paintwork will dry out.
Polishing is necessary only if the paint has become dull or if solid deposits have become attached to it.
Paintwork polish with silicone forms a protective film, making waxing unnecessary.
Plastic body parts must not be treated with wax or polishing agents.
Vehicle care 223
Windows and windscreen wiper blades
Use a soft lint-free cloth or chamois leather together with window cleaner and insect remover.
When cleaning the rear window, make sure the heating element inside is not damaged.
For mechanical removal of ice, use a sharp-edged ice scraper. Press the scraper firmly against the glass so that no dirt can get under it and scratch the glass.
Clean smearing wiper blades with a soft cloth and window cleaner.
Sunroof
Never clean with solvents or abrasive agents, fuels, aggressive media (e.g.
paint cleaner, acetone-containing solutions etc.), acidic or highly alkaline media or abrasive pads. Do not apply wax or polishing agents to the sunroof.
Wheels and tyres
Do not use high-pressure jet cleaners.
224 Vehicle care
Clean rims with a pH-neutral wheel cleaner.
Rims are painted and can be treated with the same agents as the body.
Paintwork damage
Rectify minor paintwork damage with a touch-up pen before rust forms.
Have more extensive damage or rust areas repaired by a workshop.
Underbody
Some areas of the vehicle underbody have a PVC undercoating while other critical areas have a durable protective wax coating.
After the underbody is washed, check the underbody and have it waxed if necessary.
Bitumen/rubber materials could damage the PVC coating. Have underbody work carried out by a workshop.
Before and after winter, wash the underbody and have the protective wax coating checked.
Liquid gas system
9 Danger
Liquid gas is heavier than air and can collect in sink points.
Take care when performing work at the underbody in a pit.
For painting work and when using a drying booth at a temperature above 60 °C, the liquid gas tank must be removed.
Do not make any modifications to the liquid gas system.
Towing equipment
Do not clean the coupling ball bar with a steam-jet or high-pressure jet cleaner.
Rear carrier system
Clean the rear carrier system with a steam-jet or high-pressure jet cleaner at least once a year.
Operate the rear carrier system periodically if not in regular use, in particular during winter.
Air shutter
Clean the shutter system in the front bumper to maintain correct functionality.
Interior care
Interior and upholstery
Only clean the vehicle interior, including the instrument panel fascia and panelling, with a dry cloth or interior cleaner.
Clean the leather upholstery with clear water and a soft cloth. In case of heavy soiling, use leather care.
The instrument panel should only be cleaned using a soft damp cloth.
Clean fabric upholstery with a vacuum cleaner and brush.
Remove stains with an upholstery cleaner.
Clean seat belts with lukewarm water or interior cleaner.
Caution
Close Velcro fasteners as open
Velcro fasteners on clothing could damage seat upholstery.
The same applies to clothing with sharp-edged objects, like zips or belts or studded jeans.
Plastic and rubber parts
Plastic and rubber parts can be cleaned with the same cleaner as used to clean the body. Use interior cleaner if necessary. Do not use any other agent. Avoid solvents and petrol in particular. Do not use highpressure jet cleaners.
Vehicle care 225
226 Service and maintenance
Service and maintenance
General information ................... 226
Recommended fluids, lubricants
and parts .................................... 227
General information
Service information
In order to ensure economical and safe vehicle operation and to maintain the value of your vehicle, it is of vital importance that all maintenance work is carried out at the proper intervals as specified.
The detailed, up-to-date service schedule for your vehicle is available at the workshop.
European service intervals
Maintenance of your vehicle is required every 20000 miles or after
1 year, whichever occurs first, unless otherwise indicated in the service display.
The European service intervals are valid for the following countries:
Andorra, Austria, Belgium, Bosnia-
Herzegovina, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany,
Greece, Greenland, Hungary,
Iceland, Ireland, Israel, Italy, Latvia,
Lithuania, Luxembourg, Macedonia,
Malta, Montenegro, Netherlands,
Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden,
Switzerland, United Kingdom.
International service intervals
Maintenance of your vehicle is required every 10000 miles or after
1 year, whichever occurs first, unless otherwise indicated in the service display.
The international service intervals are valid for the countries which are not listed in the European service intervals.
Confirmations
Confirmation of service is recorded in the Service and Warranty Booklet.
The date and mileage is completed with the stamp and signature of the servicing workshop.
Make sure that the Service and
Warranty Booklet is completed correctly as continuous proof of service is essential if any warranty or goodwill claims are to be met, and is also a benefit when selling the vehicle.
Service interval with remaining engine oil life duration
The service interval is based on several parameters depending on usage.
The service display lets you know when to change the engine oil.
Recommended fluids, lubricants and parts
Recommended fluids and lubricants
Only use products that meet the recommended specifications.
Damage resulting from the use of products not in line with these specifications will not be covered by the warranty.
9 Warning
Operating materials are hazardous and could be poisonous. Handle with care. Pay attention to information given on the containers.
Engine oil
Engine oil is identified by its quality and its viscosity. Quality is more important than viscosity when selecting which engine oil to use. The oil quality ensures e.g. engine cleanliness, wear protection and oil
Service and maintenance 227
aging control, whereas viscosity grade gives information on the oil's thickness over a temperature range.
Dexos is the newest engine oil quality that provides optimum protection for gasoline and diesel engines. If it is unavailable, engine oils of other listed qualities have to be used.
Recommendations for gasoline engines are also valid for
Compressed Natural Gas (CNG),
Liquified Petroleum Gas (LPG) and
Ethanol (E85) fuelled engines.
Select the appropriate engine oil based on its quality and on the minimum ambient temperature
Topping up engine oil
Engine oils of different manufacturers and brands can be mixed as long as they comply with the required engine oil quality and viscosity.
Use of engine oil with only
ACEA A1/B1 or only A5/B5 quality is prohibited, since it can cause longterm engine damage under certain operating conditions.
228 Service and maintenance
Select the appropriate engine oil based on its quality and on the minimum ambient temperature
Additional engine oil additives
The use of additional engine oil additives could cause damage and invalidate the warranty.
Engine oil viscosity grades
The SAE viscosity grade gives information of the thickness of the oil.
Multigrade oil is indicated by two figures, e.g. SAE 5W-30. The first figure, followed by a W, indicates the low temperature viscosity and the second figure the high temperature viscosity.
Select the appropriate viscosity grade depending on the minimum ambient
All of the recommended viscosity grades are suitable for high ambient temperatures.
Coolant and antifreeze
Use only silicate-free long life coolant
(LLC) antifreeze.
The system is factory filled with coolant designed for excellent corrosion protection and frost protection down to approx. -28 °C. In northern countries with very low temperatures the factory filled coolant provides frost protection down to approx. -37°C. This concentration should be maintained all year round.
The use of additional coolant additives that intend to give additional corrosion protection or seal against minor leaks can cause function problems. Liability for consequences resulting from the use of additional coolant additives will be rejected.
Brake and clutch fluid
Only use high-performance brake fluid approved for the vehicle, consult a workshop.
Over time, brake fluid absorbs moisture which will reduce braking effectiveness. The brake fluid should therefore be replaced at the specified interval.
Brake fluid should be stored in a sealed container to avoid water absorption.
Ensure brake fluid does not become contaminated.
Technical data
Vehicle identification .................. 229
Vehicle data ............................... 231
Vehicle identification
Vehicle Identification
Number
Technical data
Identification plate
229
The Vehicle Identification Number is visible through the windscreen.
The identification plate is located on the front left door frame.
230 Technical data
Information on identification label:
1 = Manufacturer
2 = Type approval number
3 = Vehicle Identification Number
4 = Permissible gross vehicle weight rating in kg
5 = Permissible gross train weight in kg
6 = Maximum permissible front axle load in kg
7 = Maximum permissible rear axle load in kg
8 = Vehicle-specific or countryspecific data
The combined total of front and rear axle loads must not exceed the permissible gross vehicle weight. For example, if the front axle is bearing its maximum permissible load, the rear axle can only bear a load that is equal to the gross vehicle weight minus the front axle load.
The technical data is determined in accordance with European
Community standards. We reserve the right to make modifications.
Specifications in the vehicle documents always have priority over those given in this manual.
Technical data 231
Vehicle data
Recommended fluids and lubricants
European service schedule
Required engine oil quality
All European countries
(except Belarus, Moldova, Russia, Serbia, Turkey)
Engine oil quality dexos 1 dexos 2
Petrol engines
(including CNG, LPG, E85)
–
✔
Diesel engines
–
✔
Only Israel
Petrol engines
(including CNG, LPG, E85)
✔
–
Diesel engines
–
✔
In case dexos quality is unavailable you may use max. 1 litre engine oil quality ACEA C3 once between each oil change.
Engine oil viscosity grades
Ambient temperature down to -25 °C below -25 °C
All European countries and Israel
(except Belarus, Moldova, Russia, Serbia, Turkey)
Petrol and diesel engines
SAE 5W-30 or SAE 5W-40
SAE 0W-30 or SAE 0W-40
232 Technical data
International service schedule
Required engine oil quality
Engine oil quality
All countries outside Europe except Israel
Petrol engines
(including CNG, LPG, E85)
Diesel engines dexos 1 dexos 2
✔
–
–
✔
Only Belarus, Moldova, Russia, Serbia, Turkey
Petrol engines
(including CNG, LPG, E85)
Diesel engines
–
✔
–
✔
In case dexos quality is unavailable you may use the oil qualities listed below:
All countries outside Europe except Israel Only Belarus, Moldova, Russia, Serbia, Turkey
Engine oil quality Petrol engines
(including CNG, LPG, E85)
Diesel engines Petrol engines
(including CNG, LPG, E85)
Diesel engines
GM-LL-A-025
GM-LL-B-025
✔
–
–
✔
✔
–
–
✔
Technical data 233
All countries outside Europe except Israel
Engine oil quality
ACEA A3/B3
ACEA A3/B4
ACEA C3
API SM
API SN resource conserving
Petrol engines
(including CNG, LPG, E85)
Diesel engines
✔
✔
✔
✔
✔
–
✔
✔
–
–
Only Belarus, Moldova, Russia, Serbia, Turkey
Petrol engines
(including CNG, LPG, E85)
✔
✔
✔
✔
✔
Diesel engines
–
✔
✔
–
–
Engine oil viscosity grades
Ambient temperature down to -25 °C below -25 °C down to -20 °C
All countries outside Europe (except Israel), including Belarus, Moldova, Russia, Serbia, Turkey
Petrol and diesel engines
SAE 5W-30 or SAE 5W-40
SAE 0W-30 or SAE 0W-40
SAE 10W-30 1) or SAE 10W-40 1)
1) Permitted, but usage of SAE 5W-30 or SAE 5W-40 with dexos quality is recommended.
234 Technical data
Engine data
Sales designation 1.4
Engine identifier code
A14XEL
Number of cylinders
4
Piston displacement [cm 3 ]
1398
Engine power [kW] 64 at rpm 6000
Torque [Nm] at rpm
Fuel type
130
4000
Petrol
Octane rating RON recommended 95
Super schwefelfrei
(95)
1.4
A14XER
4
1398
74
6000
130
4000
Petrol
95
Super schwefelfrei
(95)
1.4
A14NEL
4
1364
88
4200-6000
200
1850-4200
Petrol
1.4
A14NET
4
1364
103
4900-6000
200
1850-4900
Petrol/LPG
1.6
A16XER
4
1598
85
6000
155
4000
Petrol
95
Super schwefelfrei
(95)
95
Super schwefelfrei
(95)
95
Super schwefelfrei
(95)
95
Super schwefelfrei
(95)
1.6
A16LET
4
1598
132
5500
230
2200
Petrol
Sales designation 1.4
Engine identifier code
A14XEL possible possible
Oil consumption [l/
1000 km]
98
Super Plus schwefelfrei
(98)
91
Benzin schwefelfrei
(91)
0.6
Sales designation
Engine identifier code
Number of cylinders
Piston displacement [cm 3 ]
Engine power [kW] at rpm
Torque [Nm]
1.4
A14XER
98
Super Plus schwefelfrei
(98)
91
Benzin schwefelfrei
(91)
0.6
1.3
A13DTE
4
1248
70
4000
190
1.4
A14NEL
98
Super Plus schwefelfrei
(98)
91
Benzin schwefelfrei
(91)
0.6
1.7
A17DTE
4
1686
81
4000
280
1.4
A14NET
98
Super Plus schwefelfrei
(98)
91
Benzin schwefelfrei
(91)
0.6
1.6
A16XER
98
Super Plus schwefelfrei
(98)
91
Benzin schwefelfrei
(91)
0.6
Technical data
1.6
A16LET
98
Super Plus schwefelfrei
(98)
91
Benzin schwefelfrei
(91)
0.6
235
1.7
A17DTC
4
1686
81
4000
280
1.7
A17DTF
4
1686
96
4000
300
1.7
A17DTS
4
1686
96
4000
300
236 Technical data
Sales designation
Engine identifier code at rpm
Fuel type
Oil consumption [l/1000 km]
Sales designation
Engine identifier code
Number of cylinders
Piston displacement [cm 3 ]
Engine power [kW] at rpm
Torque [Nm] at rpm
Fuel type
Oil consumption [l/1000 km]
1.3
A13DTE
1750-3250
Diesel
0.6
1.7
A17DTE
1750-2500
Diesel
0.6
1.7
A17DTJ
4
1686
81
3800
260
1700-2550
Diesel
0.6
1.7
A17DTC
1750-2500
Diesel
0.6
1.7
A17DTR
4
1686
92
4000
280
2000-2700
Diesel
0.6
1.7
A17DTF
2000-2500
Diesel
0.6
2.0 Turbo
A20DTH
4
1956
121
4000
350
1750-2500
Diesel
0.6
1.7
A17DTS
2000-2500
Diesel
0.6
Technical data 237
Performance
5-door hatchback
Engine
Maximum speed 2) [mph]
Manual transmission
Automatic transmission
Engine
Maximum speed 2) [mph]
Manual transmission
Automatic transmission
A14XEL A14XER
4)
–
A14NEL
4)
–
A14NET
105 3)
–
A13DTE
111 3)
–
120
–
A17DTE
126
125
A17DTC
109
–
4)
–
A16LET
138
132
A17DTF
118
114
A17DTS
4)
–
A16XER
3)
4)
2) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipment could reduce the specified maximum speed of the vehicle.
4th gear.
Value was not available at time of printing.
238
Engine
Maximum speed 2) [mph]
Manual transmission
Automatic transmission
Sports tourer
Engine
Maximum speed [mph] 5)
Manual transmission
Automatic transmission
Engine
Technical data
Maximum speed 2) [mph]
Manual transmission
Automatic transmission
A17DTJ
113
–
A17DTR
122
–
A20DTH
134
131
A14XER
109
–
A13DTE
119
–
125
124
A17DTJ
108
–
A14NEL
113
–
A14NET A16LET
138
131
A17DTR
120
–
A16XER
116
113
A20DTH
133
129
2)
5)
The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipment could reduce the specified maximum speed of the vehicle.
The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipment could reduce the specified maximum speed of the vehicle.
Technical data 239
Vehicle weight
Kerb weight, basic model without any optional equipment
5-door hatchback Engine Manual transmission without/with air conditioning
[kg]
A14XEL
A14XER
A14NEL
A14NET
A16LET
A16XER
A13DTE
A17DTC
1373/1388
1373/1388
1393/1408
1393/1408
–/1490
1393/1408
1393/1408
1503/1518
Automatic transmission
–
–
–
–/1453
–
–
–/1503
–/1443
240 Technical data
5-door hatchback without/with air conditioning
[kg]
Engine
A17DTE
A17DTF
A17DTJ
A17DTR
A17DTS
A20DTH
A20DTH 6)
Manual transmission
1503/1518
1503/1518
1503/1518
1503/1518
1503/1518
1503/1518
1503/1518
Automatic transmission
–
–
–
–
–
–/1590
–
6) With stop-start function.
Kerb weight, basic model with all optional equipment
5-door hatchback Engine Manual transmission without/with air conditioning
[kg]
A14XEL
A14XER
A14NEL
A14NET
A16LET
A16XER
A13DTE
A17DTC
–/1545
–/1545
–/1611
–/1611
–/1613
–/1578
–/1571
–/1664
Technical data 241
Automatic transmission
–
–
–
–
–
–/1613
–/1665
–/1613
242 Technical data
5-door hatchback without/with air conditioning
[kg]
Engine
A17DTE
A17DTF
A17DTJ
A17DTR
A17 DTS
A20DTH
A20DTH 6)
Manual transmission
–/1664
–/1664
–/1684
–/1689
–/1664
–/1711
–/1701
Automatic transmission
–
–
–
–
–/1731
–
6) With stop-start function.
Kerb weight, basic model without any optional equipment
Sports tourer Engine Manual transmission without/with air conditioning
[kg]
A14XER
A14NEL
A14NET
A16LET
A16XER
A13DTE
A17DTJ
A17DTR
A20DTH
A20DTH 6)
1393/1408
1471/1486
1437/1452
–/1503
1437/1452
1471/1486
1503/1518
1503/1518
1550/1565
1571/1586
Technical data 243
Automatic transmission
–
–/1503
–/1503
–/1550
–/1503
–
–
–
–/1613
–
6) With stop-start function.
244 Technical data
Kerb weight, basic model with all optional equipment
Sports tourer Engine Manual transmission without/with air conditioning
[kg]
A14XER
A14NEL
A14NET
A16LET
A16XER
A13DTE
A17DTJ
A17DTR
A20DTH
A20DTH 6)
–/1571
–/1664
–/1664
–/1664
–/1613
–/1664
–/1733
–/1733
–/1733
–/1733
Automatic transmission
–
–/1664
–/1664
–/1701
–/1664
–
–
–
–/1733
–
6) With stop-start function.
Vehicle dimensions
Length [mm]
Width without exterior mirrors [mm]
Width with two exterior mirrors [mm]
Height (without antenna) [mm]
Length of load compartment floor [mm]
Length of load compartment with folded rear seats [mm]
Load compartment width [mm]
Load compartment height [mm]
Wheelbase [mm]
Turning circle diameter [m]
Technical data 245
5-door hatchback
4419
1814
2013
1510
836
1549
1027
554
2685
11.5
Sports tourer
4698
1814
2013
1535
1069
1835
1026
721
2685
11.5
246 Technical data
Capacities
Engine oil
Engine including Filter [l] between MIN and MAX [l]
Engine including Filter [l] between MIN and MAX [l]
Fuel tank
Petrol/diesel, nominal capacity [l]
LPG, nominal capacity [l]
A14XEL,
A14XER
4.0
1.0
A17DTE,
A17DTC
4.0
1.0
A14NEL,
A14NET
4.0
1.0
A17DTF,
A17DTS
4.0
1.0
A16LET,
A16XER
4.5
1.0
A17DTJ,
A17DTR
5.4
1.0
A13DTE ecoFlex
3.2
1.0
A20DTH
4.5
1.0
56 7)
– 8)
7)
8)
A13 DTE diesel engine with stop-start system reduced capacity: 46 litres.
Value was not available at time of printing.
Tyre pressures
Engine Tyres
A14XER,
A14XEL
205/55 R16,
205/60 R16,
215/50 R17,
225/45 R17
A14NET,
A14NEL,
A16 XER
205/55 R16,
205/60 R16,
215/50 R17,
225/45 R17,
225/45 R18,
235/40 R19
Technical data 247
Comfort with up to 3 people ECO with up to 3 people front
[kPa/bar]
([psi]) rear
[kPa/bar]
([psi]) front
[kPa/bar]
([psi]) rear
[kPa/bar]
([psi])
With full load front
[kPa/bar]
([psi]) rear
[kPa/bar]
([psi])
220/2.2 (32) 220/2.2 (32) 270/2.7 (39) 270/2.7 (39) 230/2.3 (33) 270/2.7 (39)
220/2.2 (32) 220/2.2 (32) 270/2.7 (39) 270/2.7 (39) 230/2.3 (33) 270/2.7 (39)
248 Technical data
Engine Tyres
A16LET 205/65 R16, 10)9)
215/60 R16, 9)
225/50 R17, 9)
235/45 R18
235/40 R19
205/60 R16, 10)
215/50 R17 10)
A13DTE 205/55 R16,
205/60 R16,
215/50 R17,
215/60 R16,
225/45 R17
10)
9)
Only permitted as winter tyres.
Not permitted with tyre chains.
Comfort with up to 3 people ECO with up to 3 people front
[kPa/bar]
([psi]) rear
[kPa/bar]
([psi]) front
[kPa/bar]
([psi]) rear
[kPa/bar]
([psi])
With full load front
[kPa/bar]
([psi]) rear
[kPa/bar]
([psi])
230/2.3 (33) 230/2.3 (33) 270/2.7 (39) 270/2.7 (39) 240/2.4 (35) 280/2.8 (41)
240/2.4 (35) 220/2.2 (32) –
250/2.5 (36) 230/2.3 (33) –
–
–
250/2.5 (36) 290/2.9 (42)
260/2.6 (38) 300/3.0 (43)
220/2.2 (32) 220/2.2 (32) 270/2.7 (39) 270/2.7 (39) 230/2.3 (33) 270/2.7 (39)
Engine Tyres
A17DTE,
A17DTC,
A17DTF,
A17DTS
205/65 R16,
215/60 R16,
235/45 R18
205/55 R16,
10)11)
11)
225/50 R17, 11)
215/50 R17, 10)
225/45 R17,
235/40 R19
205/60 R16, 10)
Comfort with up to 3 people ECO with up to 3 people front
[kPa/bar]
([psi]) rear
[kPa/bar]
([psi]) front
[kPa/bar]
([psi]) rear
[kPa/bar]
([psi])
Technical data
With full load front
[kPa/bar]
([psi]) rear
[kPa/bar]
([psi])
249
230/2.3 (33) 230/2.3 (33) 270/2.7 (39) 270/2.7 (39) 240/2.4 (35) 280/2.8 (41)
240/2.4 (35) 220/2.2 (32) –
250/2.5 (36) 230/2.3 (33) –
–
–
250/2.5 (36) 290/2.9 (42)
260/2.6 (38) 300/3.0 (43)
10)
11)
Only permitted as winter tyres.
Not permitted with tyre chains.
250 Technical data
Engine Tyres
A17DTJ 205/65 R16, 10)9)
215/60 R16, 11)
225/50 R17, 9)
235/45 R18
205/55 R16,
215/50 R17, 10)
225/45 R17,
235/40 R19,
205/60 R16, 10)
Comfort with up to 3 people ECO with up to 3 people front
[kPa/bar]
([psi]) rear
[kPa/bar]
([psi]) front
[kPa/bar]
([psi]) rear
[kPa/bar]
([psi])
With full load front
[kPa/bar]
([psi]) rear
[kPa/bar]
([psi])
230/2.3 (33) 230/2.3 (33) 270/2.7 (39) 270/2.7 (39) 240/2.4 (35) 280/2.8 (41)
240/2.4 (35) 220/2.2 (32) –
250/2.5 (36) 230/2.3 (33) –
–
–
250/2.5 (36) 290/2.9 (42)
260/2.6 (38) 300/3.0 (43)
10)
9)
11)
Only permitted as winter tyres.
Not permitted with tyre chains.
Not permitted with tyre chains.
Engine Tyres
A17DTR 205/65 R16, 10)9)
215/60 R16, 9)
225/50 R17,
235/45 R18
205/55 R16,
215/50 R17, 10)
225/45 R17,
235/40 R19
205/60 R16 10)
Comfort with up to 3 people ECO with up to 3 people front
[kPa/bar]
([psi]) rear
[kPa/bar]
([psi]) front
[kPa/bar]
([psi]) rear
[kPa/bar]
([psi])
Technical data
With full load front
[kPa/bar]
([psi]) rear
[kPa/bar]
([psi])
251
230/2.3 (33) 230/2.3 (33) 270/2.7 (39) 270/2.7 (39) 240/2.4 (35) 280/2.8 (41)
240/2.4 (35) 220/2.2 (32) –
250/2.5 (36) 230/2.3 (33) –
–
–
250/2.5 (36) 290/2.9 (42)
260/2.6 (38) 300/3.0 (43)
10)
9)
Only permitted as winter tyres.
Not permitted with tyre chains.
252 Technical data
Engine
A20DTH 205/65 R16, 10)9)
All
Tyres
Comfort with up to 3 people ECO with up to 3 people front
[kPa/bar]
([psi]) rear
[kPa/bar]
([psi]) front
[kPa/bar]
([psi]) rear
[kPa/bar]
([psi])
With full load front
[kPa/bar]
([psi]) rear
[kPa/bar]
([psi])
230/2.3 (33) 230/2.3 (33) 270/2.7 (39) 270/2.7 (39) 240/2.4 (35) 280/2.8 (41)
215/60 R16,
225/50 R17,
235/45 R18
235/40 R19
205/60 R16, 10)
215/50 R17 10)
240/2.4 (35) 220/2.2 (32) –
250/2.5 (36) 230/2.3 (33) –
Temporary spare wheel 420/4.2 (61) 420/4.2 (61) –
–
–
–
250/2.5 (36) 290/2.9 (42)
260/2.6 (38) 300/3.0 (43)
420/4.2 (61) 420/4.2 (61)
10)
9)
Only permitted as winter tyres.
Not permitted with tyre chains.
Towing hitch installation dimensions
5-door Hatchback
Technical data 253
254 Technical data
Sports Tourer
Customer information
Vehicle data recording and
privacy ....................................... 255
Vehicle data recording and privacy
Event data recorders
The vehicle has a number of sophisticated systems that monitor and control several vehicle data.
Some data may be stored during regular operation to facilitate repair of detected malfunctions, other data is stored only in a crash or near crash event by modules in your vehicle systems that have an event data recording function such as the airbag control module.
The systems may record diagnostic data about the condition of the vehicle
(e.g. oil level or vehicle mileage) and information how it was operated (e.g.
engine speed, brake application and seat belt usage).
To read this data, special equipment and access to the vehicle is required.
Some diagnostic data is electronically fed into Vauxhall global systems when the vehicle is serviced in a workshop, in order to document the
Customer information 255
service history of the vehicle. This enables the workshop to offer you efficient maintenance and repair, tailored to your individual vehicle, each time you bring it back to the workshop.
The manufacturer will not access driver's behaviour related information about a crash event or share it with others except:
■ with the consent of the vehicle owner or, if the vehicle is leased, of the lessee
■ in response to an official request of police or similar government office
■ as part of the manufacturer's defense in case of legal proceedings
■ as required by law
256 Customer information
In addition, the manufacturer may use the collected or received diagnostic data:
■ for the manufacturer's research needs
■ to make it available for research needs where appropriate confidentiality is maintained and need is shown
■ to share summary data which is not tied to a specific vehicle with other organisations for research purposes
Radio Frequency
Identification (RFID)
RFID technology is used in some vehicles for functions such as tyre pressure monitoring and ignition system security. It is also used in connection with conveniences such as radio remote controls for door locking/unlocking and starting, and invehicle transmitters for garage door openers. RFID technology in
Vauxhall vehicles does not use or record personal information or link with any other Vauxhall system containing personal information.
Customer information 257
258
Index
A
Accessories and vehicle
modifications .......................... 181
Active head restraints................... 36
Adaptive forward lighting ... 108, 129
Adjustable air vents ................... 143
Airbag and belt tensioners ......... 103
Airbag deactivation .............. 46, 103
Airbag system .............................. 44
Air conditioning regular
operation ................................ 144
Air conditioning system .............. 138
Air intake .................................... 144
Air vents...................................... 143
Antilock brake system ................ 156
Antilock brake system (ABS) ..... 105
Anti-theft alarm system ................ 25
Anti-theft locking system .............. 25
Appearance care........................ 222
Armrest......................................... 40
Armrest storage ........................... 55
Ashtrays ....................................... 97
Automatic anti-dazzle .................. 29
Automatic light control ............... 127
Automatic locking ........................ 23
Automatic transmission ............. 152
Auxiliary heater........................... 143
B
Battery ....................................... 186
Battery discharge protection ...... 135
Battery voltage ........................... 117
Bicycle rack.................................. 57
Bonnet ....................................... 183
Brake and clutch fluid................. 227
Brake and clutch system ........... 104
Brake assist ............................... 158
Brake fluid .................................. 186
Brakes ............................... 156, 186
Breakdown.................................. 220
Bulb replacement ....................... 189
C
Capacities .................................. 246
Cargo management system ........ 83
Car Pass ...................................... 19
Catalytic converter ..................... 151
Central locking system ................ 21
Centre console lighting .............. 134
Centre console storage ............... 56
Changing tyre and wheel size ... 209
Charging system ........................ 104
Child locks ................................... 23
Child restraint installation
locations ................................... 49
Child restraint systems ................ 48
Cigarette lighter ........................... 97
Climate control ............................. 15
Climate control systems............. 137
Clock............................................. 96
Code........................................... 114
Control indicators........................ 101
Control of the vehicle ................. 145
Controls........................................ 91
Convex shape .............................. 28
Coolant and antifreeze............... 227
Cruise control .................... 108, 162
Cupholders .................................. 53
Curtain airbag system .................. 46
Curve lighting.............................. 129
D
Danger, Warnings and Cautions ... 4
Diesel fuel system bleeding ....... 188
Diesel particle filter............. 106, 150
Door open .................................. 109
Doors............................................ 24
Driver assistance systems.......... 162
Driver Information Centre........... 109
Driving characteristics and
towing tips .............................. 176
Driving hints................................ 145
E
ECO drive assistant.................... 118
Electric adjustment ...................... 28
Electrical parking brake.............. 105
Electrical parking brake fault...... 105
Electrical system......................... 198
Electronic climate control
system .................................... 139
Electronic driving programmes .. 154
Electronic Stability Control.......... 159
Electronic Stability Control and
Traction Control system.......... 106
Electronic Stability Control off..... 106
End-of-life vehicle recovery ....... 182
Engine compartment fuse box ... 199
Engine coolant ........................... 184
Engine coolant temperature
gauge ..................................... 100
Engine data ............................... 234
Engine exhaust .......................... 150
Engine oil ................... 183, 227, 231
Engine oil pressure .................... 107
Entry lighting .............................. 134
Event data recorders.................. 255
Exit lighting ................................ 135
Exterior care .............................. 222
Exterior light ............................... 108
Exterior lighting .................... 12, 126
Exterior mirrors............................. 28
F
Fault ........................................... 154
First aid......................................... 87
First aid kit ................................... 87
259
Fixed air vents ........................... 143
Flex-Fix system............................ 57
Fog light ..................................... 108
Fog lights ................................... 192
Folding ......................................... 28
Front airbag system ..................... 44
Front fog lights ........................... 132
Front seats.................................... 37
Front storage................................ 54
Fuel............................................. 169
Fuel consumption - CO
2
-
Emissions ............................... 175
Fuel for diesel engines .............. 170
Fuel for liquid gas operation....... 170
Fuel for petrol engines ............... 169
Fuel gauge ................................... 99
Fuel selector ................................ 99
Fuses ......................................... 198
G
Gauges......................................... 98
General information ................... 176
Glovebox ..................................... 53
Graphic-Info-Display, Colour-
Info-Display ............................ 112
H
Halogen headlights .................... 189
Hand brake......................... 156, 157
Hazard warning flashers ............ 131
260
Headlight flash ........................... 128
Headlight range adjustment ...... 128
Headlights................................... 126
Headlights when driving abroad 128
Head restraint adjustment ............. 8
Head restraints ............................ 35
Heated ......................................... 29
Heated rear window ..................... 32
Heated steering wheel ................. 92
Heating ........................................ 40
Heating and ventilation system . 137
Height adjustable rear floor cover 81
High beam ......................... 108, 127
High beam assist........................ 108
Hill start assist ........................... 158
Horn ....................................... 13, 92
I
Identification plate ..................... 229
Ignition switch positions ............. 146
Immobiliser .......................... 27, 108
Indicators...................................... 98
Information displays.................... 109
Instrument cluster ........................ 98
Instrument panel fuse box ......... 201
Instrument panel illumination ..... 198
Instrument panel illumination
control .................................... 133
Instrument panel overview ........... 10
Interactive driving system........... 160
Interior care ............................... 224
Interior lighting............................ 133
Interior lights ...................... 133, 198
Interior mirrors.............................. 29
Interruption of power supply ...... 154
Introduction .................................... 3
ISOFIX child restraint systems .... 52
J
Jump starting ............................. 219
K
Key, memorised settings.............. 21
Keys ............................................. 19
Keys, locks................................... 19
L
Lane departure warning..... 106, 168
Lashing eyes ............................... 83
Lighting features......................... 134
Light switch ................................ 126
Load compartment ................ 24, 74
Load compartment cover ............. 78
Load compartment fuse box ...... 202
Loading information ..................... 89
Low fuel ..................................... 107
Low washer fluid ........................ 108
M
Malfunction indicator light .......... 104
Manual anti-dazzle ...................... 29
Manual mode ............................. 153
Manual transmission .................. 155
Manual windows .......................... 30
Memorised settings...................... 21
Mirror adjustment ........................... 8
Misted light covers ..................... 133
N
New vehicle running-in .............. 146
Number plate light ..................... 197
O
Object detection systems........... 163
Odometer ..................................... 98
Oil, engine.......................... 227, 231
Outside temperature .................... 95
Overrun cut-off ........................... 147
P
Parking ................................ 17, 150
Parking assist ............................ 163
Parking brake ............................ 157
Parking lights ............................. 132
Particulate filter........................... 150
Performance .............................. 237
Performing work ........................ 182
Pollen filter ................................. 144
Power outlets ............................... 97
Power steering............................ 105
Power windows ............................ 30
Preheating ................................. 106
Puncture..................................... 213
Q
Quickheat................................... 143
R
Radio Frequency Identification
(RFID)..................................... 256
Radio remote control ................... 20
Reading lights ............................ 134
Rear carrier system...................... 57
Rear floor storage cover .............. 81
Rear fog light ............................. 108
Rear fog lights ........................... 132
Rear seats.................................... 40
Rear window wiper/washer .......... 95
Recommended fluids and
lubricants ........................ 227, 231
Reduced engine power.............. 108
Refuelling ................................... 172
Retained power off..................... 146
Reversing lights ......................... 133
Ride control systems.................. 159
Roof.............................................. 33
Roof rack ..................................... 88
S
Safety net .................................... 85
Seat adjustment ....................... 6, 37
Seat belt ........................................ 8
Seat belt reminder ..................... 103
Seat belts ..................................... 41
Seat position ................................ 37
Selector lever ............................. 152
Service ............................... 144, 226
Service display .......................... 100
Service information .................... 226
Service vehicle soon .................. 104
Side airbag system ...................... 45
Sidelights.................................... 126
Side turn signal lights ................ 197
Spare wheel ............................... 216
Speedometer ............................... 98
Starting and operating................ 146
Starting off ................................... 16
Starting the engine .................... 146
Steering wheel adjustment ...... 9, 91
Steering wheel controls ............... 91
Stop-start system........................ 148
Storage......................................... 53
Storage compartments................. 53
Sunglasses storage ..................... 54
Sunroof ........................................ 33
Sunvisor lights ........................... 134
261
Sun visors .................................... 32
Symbols ......................................... 4
T
Tachometer ................................. 99
Tail lights ................................... 193
Three-point seat belt .................... 42
Tools .......................................... 205
Top-tether fastening eyes ............ 52
Towing................................ 176, 220
Towing another vehicle ............. 221
Towing equipment ..................... 177
Towing hitch installation
dimensions ............................. 253
Towing the vehicle ..................... 220
Traction Control system ............. 159
Traction Control system off......... 106
Traffic sign assistant................... 165
Trailer coupling........................... 176
Trailer stability assist ................. 180
Trailer towing ............................. 176
Transmission ............................... 16
Transmission display ................. 152
Tread depth ............................... 208
Trip computer ............................ 118
Trip odometer .............................. 98
Turn and lane-change signals ... 131
Turn signal ................................. 103
Tyre chains ................................ 209
Tyre designations ...................... 206
262
Tyre pressure ............................ 206
Tyre pressure monitoring
system............................. 107, 207
Tyre pressures ........................... 247
Tyre repair kit ............................. 210
U
Ultrasonic parking assist . . . 106, 163
Underseat storage ....................... 55
Upshift........................................ 105
Using this manual .......................... 3
V
Vehicle checks............................ 182
Vehicle data................................ 231
Vehicle data recording and
privacy..................................... 255
Vehicle dimensions .................... 245
Vehicle Identification Number .... 229
Vehicle jack................................ 205
Vehicle messages ..................... 114
Vehicle personalisation ............. 121
Vehicle security............................ 25
Vehicle specific data ...................... 3
Vehicle storage........................... 181
Vehicle tools............................... 205
Vehicle unlocking ........................... 6
Vehicle weight ........................... 239
Ventilation................................... 137
W
Warning chimes ......................... 117
Warning lights............................... 98
Warning triangle .......................... 87
Washer and wiper systems ......... 14
Washer fluid ............................... 185
Wheel changing ......................... 213
Wheel covers ............................. 209
Wheels and tyres ....................... 205
Windows....................................... 30
Windscreen................................... 30
Windscreen wiper/washer ........... 93
Winter tyres ............................... 205
Wiper blade replacement .......... 188
X
advertisement
Key Features
- Start-stop system
- Airbags
- Seat belts
- Traction control
- Cruise control
- Lane departure warning
- Heated seats
- Heated rear window
- Sunroof
- Power windows
