C3100FFU1 - Ford Fusion Install Manual

C3100FFU1 - Ford Fusion Install Manual
INSTALLATION &
OPERATION
MANUAL
2014 Ford Fusion
Speaker Bracket
2014 FORD FUSION SPEAKER INSTALLATION
Table of Contents:
Page No:
1.
2.
Description:
Installation
Warranty Information
Installation:
1.
2.
3.
4.
5.
Remove front bumper assembly from the vehicle
Place speaker and bracket in cavity under the driver’s side headlight within support beam
Fasten bracket to vehicle using supplied hardware
Route and attach speaker wires to speaker
Extend the BLUE (Positive) and the WHITE (Negative) speaker wires to your siren amplifier and
connect as shown in the amplifiers instructions and test the siren for proper operation.
6. Replace front bumper assembly to car.
IMPORTANT:
Read all instructions and warnings before installing and using.
INSTALLER: This manual must be delivered to the end user of this equipmen
1
Installation Photos
2
Notes
3
!
WARNING!
LLarger wires and tight connections will provide longer service life for components. For high current wires it is highly
re
commended
that terminal blocks or soldered connections be used with shrink tubing to protect the connections. Do
not
n use insulation displacement connectors (e.g. 3M® Scotchlocknotonnectors). Route wiring using grommets
and sealant when passing through compartment walls. Minimize the number of splices to reduce voltage drop. High
ambient temperatures (e.g. under hood) will significantly reduce the current carrying capacity of wires, fuses, and
circuit breakers. Use "SXL" type wire in engine compartment. All wiring should conform to the minimum wire size and
other recommendations of the manufacturer and be protected from moving parts and hot surfaces. Looms, grommets,
cable ties, and similar installation hardware should be used to anchor and protect all wiring. Fuses or circuit breakers
should be located as close to the power takeoff points as possible and properly sized to protect the wiring and devices.
Particular attention should be paid to the location and method of making electrical connections and splices to protect
these points from corrosion and loss of conductivity. Ground terminations should only be made to substantial chassis
components, preferably directly to the vehicle battery. The user should install a fuse sized to approximately 125% of
the maximum Amp capacity in the supply line to protect against short circuits. For example, a 30 Amp fuse should
carry a maximum of 24 Amps. DO NOT USE 1/4" DIAMETER GLASS FUSES AS THEY ARE NOT SUITABLE FOR
CONTINUOUS DUTY IN SIZES ABOVE 15 AMPS. Circuit breakers are very sensitive to high temperatures and will
"false trip" when mounted in hot environments or operated close to their capacity.
Wear hearing protection when testing, Use siren only for emergency response, Roll up windows when siren is
operating, Avoid exposure to the siren sound outside of vehicle.
WARRANTY
Code 3, ®Inc.'s emergency devices are tested and found to be operational at the time of manufacture. Provided they are installed and
operated in accordance with manufacturer's recommendations, Code 3, Inc. guarantees all parts and components except the lamps to a period
of 1 year (unless otherwise expressed) from the date of purchase or delivery, whichever is later. Units demonstrated to be defective within the
warranty period will be repaired or replaced at the factory service center at no cost.
Use of lamp or other electrical load of wattage higher than installed or recommended by the factory, or use of inappropriate or inadequate
wiring or circuit protection causes this warranty to become void. Failure or destruction of the product resulting from abuse or unusual use and/or
accidents is not covered by this warranty. Code 3, Inc. shall in no way be liable for other damages including consequential, indirect or special
damages whether loss is due to negligence or breach of warranty.
CODE 3, INC. MAKES NO OTHER EXPRESS OR IMPLIED WARRANTY INCLUDING, WITHOUT LIMITATION, WARRANTIES OF
FITNESS OR MERCHANTABILITY, WITH RESPECT TO THIS PRODUCT.
PRODUCT RETURNS
If a product must be returned for repair or replacement*, please contact our factory to obtain a Return Goods Authorization Number
(RGA number) before you ship the product to Code 3, Inc. Write the RGA number clearly on the package near the mailing label. Be sure you
use sufficient packing materials to avoid damage to the product being returned while in transit.
*Code 3, Inc. reserves the right to repair or replace at its discretion. Code 3, Inc. assumes no responsibility or liability for expenses incurred for the removal and /or reinstallation of products requiring
service and/or repair; nor for the packaging, handling, and shipping: nor for the handling of products return to sender after the service has been rendered.
PROBLEMS OR QUESTIONS? CALL OUR TECHNICAL ASSISTANCE HOTLINE (314) 996-2800
WWW.CODE3PSE.COM
Code 3®, Inc.
10986 N. Warson Road
St. Louis, Missouri 63114-2029—USA
Ph. (314) 426-2700 Fax (314) 426-1337
Part No. T57762 Rev. 0 12/2014
©2013 Code 3, Inc.
Code 3® a registered trademark of Code 3, Inc.
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement