1500*
U S E A N D C A R E / I N S TA L L AT I O N G U I D E
30”
™
Gas Self Clean with Convection
Gas Manual Clean with Convection
Range
A SPECIAL MESSAGE TO OUR CUSTOMERS
Dear Valued Customer,
Congratulations on making a smart choice! You have joined an elite group of cooking enthusiasts who demand only the very best from their
appliances. A Capital Cooking appliance promises years of enjoyment and maximum pleasure, allowing cooks everywhere to create culinary
memories that last a lifetime.
Because of the unique features found in our appliances, we urge you to read this manual thoroughly before installation and use.
And please retain this manual for future reference; it is an invaluable guide to help you better understand your Capital Cooking
appliance.
Since your satisfaction is our topmost priority, please feel free to contact our service experts. You may reach us toll free at 866.402.4600,
or dial the factory direct at 562.903-1168. You can fax us a list of your concerns, comments, and/or compliments at 562.903-1167, or drop
us an email at customerservice@capital-cooking.com. Feel free to also write us at 13211 East Florence Ave. Santa Fe Springs, CA 90670.
Our products are proudly designed and manufactured in America, and we trust that our strict adherence to the highest quality
assurance standards will provide you with years of trouble free, gourmet cooking.
Happy Cooking!
Capital Cooking Test Kitchen Specialists
TABLE OF CONTENTS
30 Precision Features
3
Models
4
Warnings
5
Safety Practices / Electrical, General
6
Safety Practices / Cooking
7
Range Parts Identification
9
Using The Range-top / Power-flo™ Burners
10
Using The Rangetop
11
Using Your Oven
13
Using Your Oven - Self Clean Mode
17
Care And Maintenance / Locating the Rating Plate
19
Troubleshooting
20
Installation Instructions
22
Service / Warranty
37
CERTIFIED FOR USA AND CANADA
30” PRECISION FEATURES
30” PRECISION GAS RANGES
FEATURES/BENEFITS:
WHY GAS SELF CLEAN?
Because the benefits are boundless! Natural gas
and LPG are “clean and green” being a readily
available natural resource that is energy efficient
and environmentally friendly. In fact, we have
enough of this natural resource to power the world
for hundreds of years. And did you know that gas
powered ovens are less expensive to operate than
electric ovens?
POWER-FLO™ BURNERS
These versatile burners are the most advanced burners
available in the industry. They allow simmering from
140 degrees to a powerful 19,000 BTUs. Not only
are they powerful, but they are energy efficient, and
environmentally conscious. The
Power-Flo™ burners use LESS
gas at higher BTUs, thus saving
on precious natural resources,
while delivering astounding
levels of power and control.
POWER-WOK BURNER
Our incredibly powerful wok
burner generates 25,000 BTUs.
INFRA-Q™
(FOR GSCR MODELS ONLY)
Now you can have true restaurant quality steaks
and seared Ahi in the comfort of your own kitchen.
Capital’s exclusive Infra-Q ™ infrared-BBQ Grill
system utilizes 15,000 BTUs and sears up to
1500 degrees, while allowing you the control
to safely cook vegetables, and fish all on the
same burner. Features our
exclusive Tru-Side™ grates
that help reduce flare-ups,
and channel grease away
from the burner.
THERMO-GRIDDLE™
Our solid stainless steel
thermostatically
controlled
griddle plate gives you price
control over the griddle
area. From 15,000 BTUs
on a 9” griddle sections provide precise control
and performance. And it will never rust!
Guaranteed!
WHY GAS SELF CLEAN?
Because the major by-product of burning gas is
water (H2O). Our gas ovens, therefore, naturally
create a moisture laden cooking environment which
is why roasts, cakes, cookies and desserts retain
their moisture during the cooking process. The result
is more flavorful, moist AND healthier cuisine.
ROTISSERIE (GSCR ONLY)
Every Precision Series ga
self clean range (GSCR)
features the first ever,
motorized rotisserie system
in a professional style range.
What’ more the rotisserie, complete with rod,
heavy duty cast stainless steel prongs and
basting pan come STANDARD!
Cooking with gas...
What a Capital idea!
FLEX-ROLL™ OVEN RACKS (SELF CLEAN ONLY)
Our patent pending Flex Roll™
oven racks provide the smoothest,
most effortless range of motion in
any oven EVER manufactured!
INFRA-BROIL™
Our gas infrared broiler beneath
glass generates 18,000 BTUS
of power. And the radiant glass
makes clean-ups a snap! (Note:
24” range does not feature
glass infrared broil.)
STAY-KOOL™ KNOBS
Our restaurant grade, die cast
chrome plated metal knobs
feature bold red graphics for
easy readings of settings, and
plastic inserts that stay cooler
to the touch when using your range.
(Available in Black or Red.)
30” PRECISION SERIES MODELS (SELF CLEAN / MANUAL CLEAN)
GCR304
GSCR305 /
GCR305 /
GRT305
GSCR304Q
GSCR304G
GSCR305
In the commonwealth of massachusetts, gas connection must be performed by a licensed plumber or gas fitter.
WARNINGS!
WARNING! If the information in this manual is
not followed exactly, a fire or explosion may
result causing property damage, personal injury
or death.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance
• Do not touch any electrical switch
• Do not use any phone in your building
• Immediately call your gas supplier from a neighbors
phone. Follow the gas supplier’s instructions.
• If you can not reach your gas supplier, call the fire department.
Installation and service must be performed by a
qualified installer, service agency or the gas supplier.
The appliance and its individual shutoff valve must
be disconnected from the gas supply piping
system during any pressure testing of that system
test pressures in excess of 5 psi (35 kpa).
The appliance must be isolated from the gas supply
piping system by closing its individual manual
shutoff valve during any pressure testing of the
gas supply piping system at test pressures equal
or less than 5 psi (35 kpa).
WARNING! Disconnect Power before installing.
Before turning power ON, be sure that all
controls are in the OFF.
IMPORTANT! Installation must conform with local
codes or, in the absence of local codes, with the
National fuel Gas Code, ANSI Z223.1/NFPA 54.
• Smother flames with a close fitting lid, or any metal tray.
• Turn OFF the burner. Be careful to prevent burns.
If the flames do not extinguish, immediately
evacuate and call the fire department.
• NEVER pick up a flaming pan. By doing so, you may be burned.
• DO NOT use water or a wet dishcloth on fire.
A violent steam explosion will result. Use a fire
extinguisher only if:
• You have CLASS ABC extinguisher and
you know how to operate it.
• The fire is small and contained in the
area where it started.
• The fire department has been called.
• You can fight the fire with your back to
the exit.
FOR YOUR SAFETY! If You Smell Gas:
Shut off gas to the appliance. Extinguish any
open flames. If odor persists, immediately call
your gas supplier.
This appliance was designed for ease of
installation and operation. However, we
recommend that you read all sections of this
manual before beginning installation and that
your range is installed by an approved gas
installation technician capable of reviewing and
performing the manufacturers installation checklist
included in your information packet.
The installation of appliances assigned for
manufactured (mobile) home installation must
conform with the Manufactured Home Construction
and Safety and Safety Standard, Title 24 CFR, Part
3280 or, when such standard is not applicable,
the Standard for Manufactured Home
I n s t a l l a t i o n s , ANSI/NCSBCS A225.1, or with
local codes as applicable.
The installation of appliances designed for
Recreation Park Trailers must conform with state
or other codes or, in the absence of such codes,
with the standard for Recreational Park Trailers,
ANSI A119.5.
The appliance, when installed, must be electrically
grounded in accordance with local codes or, in
the absence of local codes, with the National
Electrical Code, ANSI/NFPA 70
WARNING! If the information in this manual is
not followed exactly, a fire or explosion may
result, causing property damage, personal injury
or death. Please read the installation, operating
and maintenance instructions thoroughly before use.
IMPORTANT! All ranges must be installed with
a back-guard. One of three available backguards must be ordered separately and installed
at the back of the range. The three back-guard
choices include Island Trim, Low Back or HighShelf. Before using the range insure that it is
equipped with a proper back-guard. Refer to the
Installation Instructions accompanying this
appliance.
CAUTION! When connecting the unit to
propane gas, make certain the propane tank is
equipped with its own high-pressure regulator
in addition to the pressure regulator supplied
with the range. The pressure of the gas
supplied to the appliance must not exceed 14”
(34.57 mB) water column from the propane
gas tank to the pressure regulator.
CAUTION! Do not store or use gasoline or any
other flammable liquids in the vicinity of this or
any other appliance.
P L E A S E R E TA I N T H I S
MANUAL FOR FUTURE
REFERENCE!
PLEASE NOTE:
In the Commonwealth of Massachusetts, gas
connection must be performed by a licensed
plumber or licensed gas fitter.
SAFETY PRACTICES / ELECTRICAL, GENERAL
ELECTRICAL SAFETY:
Electrical Requirements and Grounding Instructions
*It is recommended that a dedicated circuit servicing
this appliance be provided.
CAUTION: ALL MODELS
IN CASE OF AN ELECTRICAL FAILURE
If for any reason a gas control knob is turned ON and
there is no electric power to operate the electronic
igniters on the range burners, turn OFF the gas
control knob and wait 5 minutes for the gas to
dissipate before lighting the range burner manually.
To light the range burners, carefully hold a lighted
match to the burner ports and turn the gas control
knob to HI. During a power failure, you can manually
light the standard range burners only, but each must
be lit with a match.
Note: For Precision Gas Ranges, the gas oven, grill,
Thermo-griddle™ and infrared oven broiler burners
CANNOT be lit manually during a power failure.
WARNING! Do not under any circumstances cut
or remove the separate ground wire or the third
(ground) prong from the power cord plug.
PLEASE READ CAREFULLY:
All gas self clean range models require an electrical
circuit rated at 120 volts, 60 Hz., and 20 Amps.
(VERIFY) For personal safety, this appliance must
be connected to a properly grounded and polarized
electrical power supply. Always disconnect the
electrical plug from the wall receptacle before
servicing this unit. See Installation Instructions for
electrical requirements and grounding instructions.
It is the personal responsibility and obligation of
you, the user, to have this appliance connected to
the electrical power supply in accordance with the
National Electrical Code and/or applicable local
codes and ordinances by a qualified electrician.
• If you smell gas, your installer has not done a proper
job of checking for leaks. If the connections
are not perfectly tight, you can have a small
leak and therefore a smell a faint gas odor.
Finding a gas leak is not a “do-it-yourself”
procedure. Some leaks can only be found with
the burner control in the “ON” position and
a qualified service technician must do this.
• In the event a burner goes out and gas escapes,
open a window or door immediately. DO NOT
attempt to use the range until the gas has had time
to dissipate. Wait at least 5 minutes before using
the range.
GENERAL SAFETY:
Your new range has been designed to be a
safe, reliable appliance when properly used and
maintained. If not properly used, it could be
dangerous. Read ALL the instructions in this Use
and Care Guide carefully before using this range.
WARNING! These precautions will reduce the risk
of burns, electric shock, fire, and injury to persons.
Use extreme care when using this restaurant
caliber range as this appliance provides intense
heat and can increase accident potential.
• Safety precautions must be followed when using any kitchen appliance.
•Insure proper installation and servicing. Follow
the installation instructions provided with this
product. Have the range installed and grounded
by a qualified technician.
• Have the installer show you where the gas supply
shut off valve is located so that you know how and
where to turn off the gas to the range.
• DO NOT repair or replace any part of the appliance
unless specifically recommended in this manual.
All other servicing should be referred to a
qualified technician.
• Children SHOULD NOT be left alone or unattended
in an area where appliances are in use. They
should never be allowed to sit or stand on any part
of the appliance.
CAUTION! Do not store items of interest to children
above the range or behind it. If children should
climb onto the appliance to reach these items,
they could be seriously injured.
•NEVER use any part of the range for storage.
Flammable materials can catch fire and plastic
items may melt or ignite.
• If the range is near a window, be certain the
curtains do not blow over or near the range burners,
griddle or broiler section; they could catch fire and
cause serious injury.
• DO NOT USE WATER ON GREASE FIRES! Turn
appliance off and smother fire with baking soda or
use a dry chemical or foam-type extinguisher.
SAFETY PRACTICES / COOKING
• NEVER let clothing, potholders, or other flammable
materials come into contact with or too close to any
element, burner, or burner grate until it has cooled.
Fabric may ignite and result in personal injury.
COOKING SAFETY:
• USE ONLY DRY POTHOLDERS. Moist or damp
potholders on hot surfaces may cause burns from
the steam. Do not use a towel or other bulky cloth
in place of potholders. Do not let potholders touch
hot elements, hot burners, or burner grates.
• FOR PERSONAL SAFETY, wear proper apparel.
Loose fitting garments or hanging sleeves should
never be worn while using this appliance. Some
synthetic fabrics are highly flammable and should
not be worn while cooking.
• DO NOT use aluminum foil as a shield against
food spills or drippings around the burners or
control panel area. This could obstruct the flow of combustion and ventilated air. This can damage
the finish of the range.
WARNING! This appliance is for cooking! Based
on safety considerations, never use the range to
warm or heat a room. Such use can damage the range.
• DO NOT TOUCH THE BURNER GRATES OR THE
IMMEDIATE SURROUNDING AREAS adjacent to
the burners. When in use these areas may become
hot enough to cause burns.
• NEVER leave the range unattended when using
high flame settings. Boil-overs cause smoking
and greasy spills that may ignite. More importantly,
if the burner flames are smothered, unburned
gas will escape into the room. See inside front
cover regarding gas leaks.
• ONLY certain types of glass, heat proof glassceramic, ceramic, earthenware or other glazed
utensils are suitable for range use. This type
of utensil may break with sudden temperature
changes. Use only on low or medium heat settings
according to the utensil manufacturer’s directions.
• DO NOT HEAT UNOPENED FOOD CONTAINERS.
A buildup of pressure may cause the container to burst.
• DURING COOKING, set the burner control so that
the flame heats only the bottom of the pan and
does not extend beyond the bottom of the pan.
•USE CAUTION to ensure that drafts like those
from forced air vents or fans do not blow flammable
materials toward the flames or push the flames so
that they extend beyond the edges of the pot.
• ALWAYS use utensils that have flat bottoms, large
enough to cover the burner. The use of undersized
utensils could expose a portion of the flame and
may result in ignition of clothing.
•TO MINIMIZE BURNS, ignition of flammable
materials and unintentional spills, position handles
of utensil inward so that it does not extend over
adjacent work areas, cooking areas or the edge
of the range.
•HOLD THE HANDLE of the pan to prevent
movement of the utensil when stirring food.
•DO NOT USE the Infra-grill™ BBQ top section
for cooking excessively fatty meats or products
that promote flare-ups.
• GREASE IS FLAMMABLE. Let hot grease to cool
before attempting to handle it. Avoid letting grease
deposits to collect. Clean after each use.
• KEEP BURNER PORTS CLEAN. This is essential
for proper lighting and maintenance of the burners.
It is necessary to clean the burner ports when
there is a boil over or when the burner does
not light though the electronic igniters click.
• CLEAN THE RANGE-TOP SECTION WITH CAUTION.
Avoid steam burns; do not use a wet sponge or cloth to
clean the range while it is hot. Some cleaners produce
noxious fumes if applied to a hot surface. Follow
directions provided by the cleaner manufacturer.
• BE SURE ALL RANGE CONTROLS ARE TURNED OFF
and the range is cool before using any type of aerosol
cleaner on or around the range. The chemical that
produces the spraying action could, in the presence
of heat, ignite or cause metal parts to corrode. Only
an authorized service technician should perform
Service. Technicians must disconnect the power
supply before servicing this unit.
•CLEAN THE VENTILATOR HOOD and filters
above the range frequently so grease deposits
from cooking vapors do not accumulate on them.
•IN CASE OF FIRE or when intentionally “flaming”
liquor or other spirits on the range, follow hood
manufacturer’s instructions.
•INSTALL A SMOKE DETECTOR in or near the kitchen.
• TURN THE KNOB CONTROL TO OFF if a burner
goes out and gas escapes. Open a window or door.
DO NOT attempt to use the range until the gas has
had time to dissipate.
WARNING! To reduce the risk of tipping of the
appliance, it must be secured by a properly installed
anti-tip device. Verify that the anti-tip device is
engaged per installation instructions (note: anti-tip
device is required on all gas self-clean ranges.)
• When using the oven: DO NOT touch the interior
surfaces of the oven or the exterior area
immediately surrounding the door. Interior oven
surfaces become hot enough to cause burns. The
heat deflector, which deflects heat away from the
range and the trim on the top and sides of the
oven door, will also be hot when the oven is in use.
SAFETY PRACTICES / COOKING
• Place oven racks in desired position while oven is
cool. If a rack must be moved while the oven is
hot, do not let the potholders contact the hot
infrared burner.
• Use care when opening the oven door; let
hot steam or air escape before removing or
replacing foods.
2. Place the oven racks in the proper position before turning on the oven.
•DO NOT rub move, or remove the door gasket.
It is essential for a good seal during baking.
For correct rack position, check your recipe.
The most frequently used position is number 2.
The rack positions are numbered from the bottom
to the top as in the floors of a building.
• BE CAREFUL not to damage the screen covering
the infrared broiler of the gas oven. If the screen is
damaged, air can enter the distribution box behind
the screen, possibly resulting in an explosion.
CAUTION! Do not use aluminum foil to cover
the oven racks or to line the oven. Heat can be
trapped beneath the foil, this can cause damage
to the oven and food may not cook correctly.
• In the event that personal clothing catches fire,
DROP AND ROLL immediately to extinguish flames.
3. Before BAKING and BROILING:
Turn on the oven and broiler burners one at a
time for 20 to 30 minutes each. This burns off the
manufacturing oils used by the factory. Turn the
oven burner on to 450°F and then the broiler
burner on to “Broil”. Be sure to turn on the
ventilator above your range while these burners
are on, as there will be an odor.
• DO NOT obstruct the flow of combustion or
ventilation air.
• For safety reasons and to avoid equipment damage,
never sit, stand, or lean on either oven door.
•Service should only be performed by a
qualified, Factory Authorized Service Technician.
Technicians must disconnect the power supply
before servicing this unit.
CALIFORNIA PROPOSITION 65 WARNING:
The burning of gas cooking fuel generates some
by products which are on the list of substances
which are known by the State of California to
cause Cancer or reproductive harm. California law
requires business to warn customers of potential
exposure to these substances. To minimize
exposure to these substances, always operate this
unit according to the instructions contained in this
booklet and provide good ventilation to the room
when cooking with gas.
1. Remove all packing materials and labels from your appliance. If the installer has not set up your appliance, please do it now.
RANGE PARTS IDENTIFICATION
30” Model Shown, model # SC305
OVEN PARTS IDENTIFICATION
1. Oven
2. Oven Light
3. Broiler Burner (behind glass)
4. Oven Thermostat Sensing Bulb
5. Door Lock
6. Rotisserie Rod
7. Meat Holder
8. Vertical Rod Support
9. Oven Baffel
10. Convection Fan (center back wall
of oven can behind baffle)
11. Heat Shield
RANGE SIDE IDENTIFICATION
RANGE PARTS IDENTIFICATION
1. Adjustable Feet
2. Adjustable Casters
1. Power Flo Wok Burner
2. Power Flo Standard Burner
3. Wok Grate
4. Burner Grate
5. Island Trim
6. Oven Light
7. Convection
8. Rotisserie
9. Indicating Lights
10. Drip Pan Handle
11. Oven Door
12. Door Handle
13. Door Glass
14. Kickplate
USING THE RANGE-TOP / POWER-FLO™ BURNERS
POWER-FLO™ BURNERS
Your new gas range is equipped with the latest in
burner technology. The Power-Flo™ burners are
designed for maximum control and the precise use
of heat where it matters most. The large top-cap
spreads the simmer flame over the bottom of a pot
to avoid too much heat being concentrated in the
center, thus avoiding burning of delicate sauces.
The flame ring at the bottom stabilizes the main
ports so as to achieve higher heat and maintain
proper combustion of the burners, leading to greater
efficiency and no yellow tips. It is always ON when
the burner is in use. The burner should never be
operated if the cap is not in place.
All the range-top burners have electronic spark
ignition to eliminate continuously burning pilots.
When the main burner flame is blown out, it will relight.
SIMMERING
Your new range-top has exceptionally low simmering
capabilities. The large cap serves as a heat diffuser to
spread out the heat to avoid having a center hot spot.
keep in mind that because of the high heat capacity
of the outer burner, and the mass of the burner grates
(they retain heat longer than lighter, conventional
grates), some foods may continue to cook by retained
heat after the burner has been turned off.
When using the simmer, turn the main burner knob
down to the simmer position. Should a strong draft
or boil over extinguish the simmer flame it will relight
automatically as the main burner would.
10
ELECTRONIC IGNITERS
If a burner does not ignite, listen for the clicking
sound. If the burner does not click, TURN OFF
BURNER. Check the circuit breaker for a blown
fuse or a tripped circuit breaker. If the igniter still
fails to operate, see page 19 “Troubleshooting”,
“Before calling For Service”.
the appliance may cause an orange flame. This will
disappear with use.
1. Burner Cap
2. Flame Ring
3. Beauty Ring
4. Burner Base
5. Igniter
6. Venturi
NOTE: If you are using propane gas, a slight pop
flash may occur at the burner ports a few seconds
after the burner has been turned “off”. This
“extinction pop” is normal for propane gas.
BURNER EFFICIENCY AND
FLAME CHARACTERISTICS
It is necessary to keep the burner ports and the
igniters clean for proper lighting and efficient
performance of the range-top burners.
The burner flame should burn completely around
the burner with no excessive noise or lifting. The
flame should be blue in color and stable with no
yellow tips.
An improper air–gas mixture may cause either a
burner flutter or a yellow tipped flame. A technician
should adjust the flame. During initial use, foreign
particles in the gas line, or dust in the air around
FLAME HEIGHT
The correct height of the flame mainly depends on
the size of the bottom of the cooking utensil, the
material of the cooking utensil, the amount and
type of food and the amount of liquid in the utensil.
Following are some basic rules for selecting
flame height.
For safety reasons the flame must never
extend beyond the bottom of the cooking
utensil. Never allow flames to curl up the
of the pan.
Utensils which conduct heat slowly (such
as glass-ceramic) should be used with
medium to low flames. If you are cooking with a large amount of liquid, a larger flame can be used.
USING THE RANGETOP
BURNER SETTINGS
The rangetop burners have an infinite number of
heat setting and there are no fixed positions on the
control knobs between HI and SIMMER. To turn the
rangetop burner on, push in on the control knob and
turn it counterclockwise to the “LITE” position. An
audible clicking sound will be heard. When the gas
has been ignited by the electronic spark igniter, turn
the knob to the desired setting.
finer department stores, specialty cooking shops, or
restaurant supply stores. If using regular cookware
be very careful if pans have plastic handles, as our
Power-Flo™ burners can flame up on the outside of
the pan and melt or bubble the handles.
THE CONTROL KNOBS
The control knobs are readily associated with the
burners they control. The RANGETOP control knobs
are labeled and in front of the burners. The oven
control is placed slightly higher than the other
control knobs. This is due to the physical size of the
commercial type thermostats used on the product.
CAUTION!
•Use extreme care when placing the grill
components into the grill compartment Avoid
contacting the ceramic igniter that could break,
preventing operation of the grill.
•Do not leave the grill unattended while in use.
Note: If the Igniter continues to click after the
burner has been lit, turn the knob to a setting other
than LITE, or HI. If the problem still persists,
please call our Service Hotline at 866-402-4600.
CAUTION! When turning on any RANGETOP
burner, be sure to stop at the “LITE” position
before turning the burner to a flame setting for
cooking. If the burner is not lit and it is turned
beyond the “LITE” position, to HI, MEDIUM, or
LO, there will be a burst of flame when the burner
does light. This could cause burns or damage to
the surrounding counter top.
BURNER GRATES
The burner grates are a heavy cast iron. They were
designed in sections to make them easier to remove
and clean.
PROPER COOKING UTENSILS
For best results we recommend using Professional
Cookware. This type of utensil can be found at your
•Do not use charcoal briquettes, ceramic plates, or
coals of any kind.
After removing all packaging materials, check to
be certain that the grill components are correctly
assembled in the grill box. The grill grates and
the burner are assembled in the grill box from
the factory.
Note: Your grill racks are constructed from stainless
steel and electro-polished to achieve a brilliant
finish. After the first use, discoloration will occur.
This is natural and unavoidable.
USING THE POWER-FLO™ WOK SECTION
Depending on your model size, your Precision Series
Self Clean Ranges are equipped with a Power-Flo™ wok
burner. On the 36”, 48” and 60” models the BTU rating
for this burner is 30,000 BTU’s. On the 30” five burner
model, the BTU rating is 25,000 BTU’s.
Wok cooking, or stir-fry cooking, requires intense,
searing heat for cooking. The Power-Flo™ Wok system
is perfectly designed to deliver high intense heat, by
spreading the flame under the diameter of the wok pan.
The flame ring at the bottom stabilizes the main burner
ports so as to achieve higher heat and maintain proper
combustion of the burners, leading to greater efficiency
and no yellow tips. It is always ON when the burner is
in use. The burner should never be operated if the cap
is not in place.
All the range-top burners have electronic spark ignition
to eliminate continuously burning pilots. When the main
burner flame is blown out, it will relight.
If a burner does not ignite, listen for the clicking
sound. If the burner does not click, TURN OFF
BURNER. Check the circuit breaker for a blown
fuse or a tripped circuit breaker. If the igniter still
fails to operate, please call our customer service
department at 1-866-402-4600.
Note: If you using propane gas, a slight pop or flash
may occur at the burner ports a few seconds after
the burner has been turned “off”. This “extinction
pop” is normal for propane gas.
COOKING ON THE INFRA-Q™ (infrared BBQ Grill)
FOR GSCR
The burner should light within approximately 5 seconds.
•Preheat the grill for approximately 5 minutes
minimum. The hot grill sears the food, sealing in the juices.
•The longer the preheat time, the faster the meat
browns and the darker the brand marks.
•Grilling requires high heat for optimum results.
High heat is necessary for searing and proper
browning. Most foods are cooked at medium
heat settings for most of the cooking time.
However, when grilling large pieces of meat or
11
USING THE RANGETOP
poultry, it may be necessary to turn the heat to
a lower setting after the initial browning. This
cooks the food through without burning the outside.
• Foods cooked for a long period of time or basted
with a sugary marinade may need a lower heat
setting near the end of the cooking time.
• After grilling and the food has been removed, turn
the knob to HI and burn off any excess grease that
may have accumulated on the burner.
• Use a brass wire brush, dipped in hot water, to
loosen food particles from the grate.
• When the grill has cooled, clean the drip tray,
and compartment.
• If a layer of ash has deposited on the ceramic
burner plates, simply brush ash to the back. It will
collect into the drip pan tray for safe and easy
clean-ups.
After the first use, discoloration will occur. This is
natural and unavoidable.
WARNING! Do not leave the BBQ section
unattended while cooking!
COOKING ON THE THERMO-GRIDDLE™
Description:
• The built in griddle is made of restaurant quality
3/8” thick stainless steel. This produces a surface
with even heat that is easy to clean.
• The griddle has a stainless steel straight tube burner
that is lit by a spark igniter. The griddle should
light with 4 clicks of the igniter. This eliminates the
need for a continuous burning pilot lighter.
• A chopping block is available as an accessory and
purchased separately. It is sized to fit on top of
the griddle surface when griddle is not in use.
• The burner is rated at 15,000 BTU/HR.
• If ash is particularly thick and impedes the airflow
of the burner and prevents safe and efficient lighting
of the burner, when burner is cool, use a handheld
vacuum cleaner and quickly vacuum away the ash.
Note: The Standard BBQ is only available on GCR
or Non Self Clean Ranges.
CAUTION!
•Use extreme care when placing the grill components
into the grill compartment. Avoid contacting
the ceramic igniter that could break, preventing
operation of the grill.
• Do not leave the grill unattended while in use.
• Do not use charcoal briquettes, ceramic plates, or
coals of any kind.
Note: Your grill racks are constructed from stainless
steel and electro-polished to achieve a brilliant finish.
12
CONTROL KNOB
• The griddle is electronically controlled with
temperatures marked on the knob from 150
degrees F to 500 degrees F.
• There are no fixed settings on the knob.
• Press and turn the knob counter-clockwise to the
temperature setting.
PREPARING THE GRIDDLE
• The griddle must be level or tilted slightly forward
for optimum performance. The griddle should
have been leveled during installation.
• PRIOR TO USE, It is NECESSARY to wash the
griddle plate with warm soapy water then rinsed
with clear water. The griddle may be used without
butter, margarine, or oil. However, a very small
amount may be used to flavor foods.
COOKING ON THE GRIDDLE
• Turn the knob to the cooking temperature to
preheat the griddle.
• Preheat 5-10 Minutes.
• Add butter, margarine, shortening or oil for more
flavor: Add food and cook!
OVEN USE
GENERAL
Your large new oven can be used in 6 cooking modes;
convection bake, regular bake, convection broil,
regular broil, convection-broil rotisserie, regular-broil
rotisserie. To help you decide which way to cook your
food read this information first. Remember this is a
new oven and the thermostat has been checked for
accuracy. Your old oven had a thermostat that over
the years got a little cold. Check your recipes for the
correct time and temperature and don’t use the old
time or temperature you were using to compensate
for your old oven being off temperature.
BURNERS
Your new Precision Series™ range is equipped
with bake and broil burners typical of those
used in restaurants. The oven broiler burner is
18,000 Btu/hr and the oven baking burner is
30,000 Btu/hr.
ELECTRIC GLOW IGNITER
The oven bake and broil burners are equipped with
an electric glow igniter and safety system which
lights the gas. There will be a delay after the control
knob has been turned on to when you actually hear
gas arrive at the burner. The burner will ignite after
the gas reaches the burner, sometimes this can take
as long as 45 seconds.
USING YOUR OVEN
USING CONVECTION BAKE AND REGULAR BAKE
TO SET THE OVEN FOR CONVECTION BAKE
AND REGULAR BAKE
Decide if you are going to use CONVECTION BAKE or
REGULAR BAKE. These cooking modes are for baking
or warming: using one, two, three or four racks. If you
are going to use Regular Bake turn the oven control
knob to the temperature used in the recipe. The Regular
BAKE light will stay ON. To use Convection Bake, simply
press the CONVECTION Button located on the front
panel to start the Convection Fan.
CONDENSATION
During any cooking process there is a certain
amount of moisture that evaporates from the food.
The amount of moisture that condenses on the
oven depends on the moisture content of the food.
The moisture will condense on any surface that
is cooler than the inside of the oven, such as the
control panel or the top of the door.
CONVECTION BAKE
Convection Bake is baking with a fan at the back
of the oven circulating the hot air in a continuous
pattern around the food. This circulating hot air heats
and browns the surface of the food more effectively
than in a standard oven. This allows most foods to
be cooked at lower oven temperature or in less time,
if baked at the regular temperature. The air is recirculated and reheated. Uncovered, longer cooking
foods such as large pieces of meat or other foods
that can be cooked in low sided baking utensils or
air leavened foods, are where you will see the most
savings in cooking time. Using multiple rack at the
same time will achieve a good time saving, as you
can cook more food at the same time. The number
of recipes requiring preheating of the oven is reduced
considerably because the heat reaches the food faster
as the hot air circulates around the food.
FOODS SUITABLE FOR CONVECTION BAKE
Air Leavened Foods (angel food cake, soufflés,
cream puffs, meringue shells)
Appetizers
Breads
Main Dishes
Oven Meals (1 to 4 racks)
Cookies
Pies
Poultry
Roasts
CONVERTING RECIPES TO CONVECTION BAKE
Low sided baking utensils will provide the best results,
as the hot air can reach all sides of the utensil easier.
The oven temperature can be left the same as the
recipe and the food cooked a shorter period of time.
The temperature can be lowered 25°F to 50°F and
the food will probably take the same length of time
to cook as the recipe states. If you find that food is
adequately browned on the outside, but not done in
the center, lower the temperature another 25°F and
add to baking time. When reducing the temperature
always check the food for doneness, a minute or
two before the minimum time stated in the recipe,
as time can always be added. Some recipes will
cook faster than others. There is no way to predict
exactly how long each recipe will take when you
convert it to convection.
Convection will be easier to use after you have used
it a few times as you will begin to understand the
way it bakes.
SELECTING UTENSILS FOR CONVECTION BAKE
Cooking by convection does not require any specially
designed baking utensils. You probably have many
utensils in your kitchen that are suitable to use. When
choosing a baking utensil, consider the material, the
size and shape as they all affect the baking time, the
appearance of the finished product.
Metal bake ware (aluminum, steel and cast iron) all
result in the fastest cooking time and the best end
product. Aluminum pans work best for all types of
baked goods. For the best browning, use a pan with
a dark or dull finish that absorbs heat, when baking
pies and breads. A shiny finish works best for cakes
and cookies, since it reflects some of the heat and
provides a tenderer surface. Cookie sheets with only
one lip will give the best results, as the heated air
can circulate all around the sides of the food.
For roasting, use bottom of the broil pan and elevate the
meat on a metal roasting rack. Glass-ceramic or glass
utensils do not conduct heat as well as metal, but they
can be used. Use them for foods that do not require a
dark brown crust or crisping, such as soufflés.
Baked items cook more quickly and evenly if they are
individually smaller in size, i.e. two or three small foods
do better than one large piece. When single food items
are baked, always center the rack. If several foods are
being baked, space them evenly on the racks.
RACK POSITIONS
One to four racks can be used simultaneously
during convection baking. Place the rack(s) in the
desired position before turning the oven on. Store
the unused racks out of the oven.
Rack position 2 (second from bottom) will probably
be used the most for single rack convection baking.
When baking on more than one rack you do not
need to stagger the pans. Allow at least 1” of space
between the oven walls and the pans so the heated
air can circulate. Pans should be placed in the
center of the oven, stacked above each rack.
REGULAR BAKE
Bake is baking with hot air; there is no fan. The air
movement comes from natural convection as the air
heats, it moves to the top of the oven. This oven
mode is the same as you have been using for baking
on one or two racks.
13
USING YOUR OVEN
FOODS SUITABLE FOR BAKE
Appetizers
Pies, Cakes
Breads
Desserts
Main Dishes
Oven Meals (1 to 2 racks)
Poultry
Roasts
CAUTION: Aluminum foil should never be used to
cover the oven racks or to line the oven bottom.
The trapped heat can damage the porcelain and
the heated air cannot adequately reach the food
being baked.
RACK POSITIONS
One or two racks can be used simultaneously during
bake. Place the rack(s) in the desired position the
before turning the oven on. Store any unused racks out
of the oven. Rack position 2 (second from bottom) will
probably be used the most for single rack baking.
If you are using two racks simultaneously, be sure to
check the food on the bottom rack sooner than the
minimum time. The food on the lower rack position
may cook slightly faster than the food on the upper
rack, particularly if you are using large baking utensils
so that one is not directly above the other and the
heated air can circulate freely around each pan. Allow
at least one inch of space between the oven walls and
the pans.
If using large or commercial size baking utensils, the
food may take a few extra minutes as the air cannot
circulate as freely as it does with a smaller pan. When
using commercial size baking utensils, use only one
rack as the heat does not have the room to circulate.
GETTING THE BEST RESULTS
BAKING:
•Follow the recipe amount and ingredients,
including the size and shape of the baking utensil
recommended in the recipe.
14
• Do not open the oven door “just to peek,” use the interior oven light and look through the window.
i.e. cakes, breads, etc. There may be a cost
for the bulletins.
• Do not use the oven for storage, especially when baking in the oven. Extra utensils, not being used for baking, can affect the food product, baking time, browning, and end result.
TO USE THE OVEN FOR COOKING OR LOW
TEMPERATURE
The oven can be used to keep hot food hot, to
dehydrate food, to warm plates, for slow cooking (as
in a crock pot), and to defrost foods.
• If you are using glass utensils, lower the temperature 25°F.
• Use a minute timer and set it for the minimum time suggested in the recipe.
You can keep hot, cooked food at serving temperature.
Set the oven to the temperature suggested in the
cart. Rare meat must be eaten when it is removed
from the oven, as it continues cooking from its own heat.
CONVECTION BAKING
• Follow the first three recommendations above.
To keep food moist, it must be covered with
aluminum foil or a lid.
• Metal utensils give better results, in convection, than do glass baking utensils. If you use glass, it usually is not necessary to lower the temperature an additional 25°F.
To dehydrate food, follow suggestions in a recipe.
• Use a minute timer and set it for less than minimum time suggested in the recipe. The first time you use a recipe in the convection mode, be sure to note the new baking time on your recipe for future reference.
To use the oven as a low cooker set the oven control
knob to 255ºF. Place the food in the oven in a pan with a
tight fitting lid. Follow recipes for this type of cooking.
To warm plates, check with the dish ware manufacturer
for the temperature for the recommended.
• Be sure to read the basic information on convection before using the oven for the first time , page 14-16.
To thaw uncooked frozen food, set the oven control
knob to “warm”. Be sure the food is tightly wrapped
in foil. Thaw the food just enough to handle it. Cook
immediately. Do not refreeze.
• Keep in mind that convection baking results vary,
depending on type of product, in many cases
standard bake yields superior results over convection.
To thaw frozen cooked food, set the oven knob to
170ºF. Loosen the freezer wrapping. Do not use
plastic wrap or wax paper in the oven.
Notes:
HIGH ALTITUDE BAKING
Recipes and baking times vary if you are baking
at altitude. For accurate information write to
the Agriculture Extension Service. Colorado
State University, Fort Collins, Colorado 80521.
Specify the type of information and the baking
mode (convention bake or bake) you need,
FOOD SAFETY
According to the United States Department of
Agriculture you should not hold foods at temperatures
between 40ºF to 140ºF for longer than 2 hours.
USING CONVECTION BROIL AND REGULAR BROIL
TO SET THE OVEN FOR CONVECTION BROIL
AND REGULAR BROIL
USING YOUR OVEN
CAUTION: Pay special attention when setting the
Oven Control Knob on “BROIL”. If you set the knob
past the “BROIL” setting, the burner will not ignite.
Decide it you are going to use BROIL or CONVECTION
BROIL. If you are going to use regular broil turn the
Oven Control knob To “BROIL”. To use Convection
Broil turn the Oven Control Knob to “BROIL” and
press the CONVECTION button to operate the fan.
The burner will ignite after the gas reaches the
burner. The “oven on” indicator light will come on to
let you know that the broiler is currently on. During
the broiling process, the infra-red burner produces
such an intense heat that the burner will cycle on
and off to maintain an efficient yet safe interior
cooking environment.
The HEATING indicator light on the valve panel cycles
on and off with burner to let the user know when the
burner is lit. This cycling process is used to evenly
distribute and safety control the intense heat that the
broil burner produces. The cycling feature prevents
the burner from producing range-damaging heat.
RACK POSITION
The rack position depends on the type and
thickness of the food. Thick pieces of meat or
poultry (1” or more) would typically be broiled
or convection broiled on rack position 3. Steaks,
chops and hamburger would typically be broiled
on rack position 4. If top browning casseroles or
bread, the thickness of the food would indicate the
position. Casseroles and bread would typically be
browned on rack position 2 (see instructions below
for more information).
CONVECTION BROIL
Convection broil is cooking by intense infrared
radiant heat supplied by the broil burner while
fan at the back of the oven circulates hot air in a
continuous pattern around the food. Convection
broil cooks the food with better results for thicker
cuts of meat. The meat sears on the outside and
retains more juices and natural flavor inside with
less shrinkage.
and 160°F to 165°F for well done. If you are cooking
pork, cook to 160°F.
FOODS SUITABLE FOR CONVECTION BROILING:
Thicker Cuts of Meat (1” or more)
Rack position #3 (same position for broiling)
A large two-piece broil pan comes with your new
range. When you are broiling, always use both
pieces. Do not cover the grid with aluminum foil.
This slotted grid allows the grease drippings to flow
into the bottom of the pan keeping it away from the
intense heat of the infra-red broiler burner. This helps to
minimize the smoking and spattering of the grease.
Thicker, Irregular-sized Pieces of Poultry (1” or more)
Rack position #2 or #3 (same position for broiling)
Thicker, Pieces of Fish (1” or more)
Rack position #3 (same position for broiling)
Top Browning: Casseroles and Breads
Rack position #2 or #3 (same position for broiling)
REGULAR BROIL
Broil is cooking by intense infrared radiant heat supplied
by the broil burner located at the top of the oven.
TO GET THE BEST RESULTS
OPEN DOOR BROILING
NOTE: Open Door Broiling is also possible with the
Precision Series oven. However, the oven door hinge
DOES NOT contain a dedicated Broil-Stop position.
To achieve the best results for Open-Door Broiling,
open oven door approximately 6-8 Inches.
FOODS SUITABLE FOR BROILING:
Appetizers
Rack position #3 or #4
Meats, Poultry, Fish (under 1”)
Rack position #4
WARNING! NEVER leave pets and/or small children
unattended while oven is in the Open Door Broiling
position. Front panel and knobs may get hot to the
touch as the heat is directly escaping to the front
section of the oven. Wear oven mitts and always
use Caution!
Top Browning: Casseroles and breads
Rack position #2 or #3
NOTE: It is not recommended to use the convection
fan and Open Door Broiling.
NOTE: The broiler pan for both broiling and convection
broiling should be placed all the way to the back of the
oven and centered on the rack for best results.
• Defrost the food before starting to cook.
USING A MEAT THERMOMETER TO BROIL AND
CONVECTION BROIL
To accurately determine the doneness of a thick steak
or chop (1-1/2) inches thick or more), use a meat
thermometer. Insert the point of the thermometer
into the side of the meat to the center. Cook the first
to 90°F for rare meat. Cook the first side 100°F for
medium to well done. Cook the second side to the
desired degree for the doneness you want, 140°F
to 145°F for rare, and 150°F to 155°F for medium
• Put food on broiler pan, center and push broiler pan to the very back of the oven rack.
• Set a minute timer for the minimum time to check the food.
• Steaks should be at least one inch thick, if rare doneness is desired. It is difficult to get rare with meat that is thinner, or to get a nice brown piece of meat.
• After half the total cooking time, turn the food over only once. It is not necessary to turn over thin 15
USING YOUR OVEN
foods (fillet of fish, Ham slices, etc.). Liver slices must be turned over.
• Use a two-piece broil pan. Two-piece broil pans are designed to minimize smoke and spatter. DO NOT cover the slotted grid with aluminum foil. This will catch the grease and could cause a fire.
• When top browning use metal or glass-ceramic bake ware. DO NOT use heat-proof Glass or pottery as this type of glassware cannot withstand
the intense heat of the broiler burner.
NOTE: You cannot use the broiler burner and the
bake burner at the same time. When one is on, the
other cannot be turned on!
USING THE OVEN ROTISSERIE
Your Gas Self Clean oven contains a rotisserie system,
complete with a vertical positioning rod, a U-bracket, a
horizontal spit rod, and heavy-duty, cast stainless steel
prongs. Also, the oven comes with a porcelain-coated,
two piece broiler pan, provided for your convenience.
Using the rotisserie is quite simple.
• Place the vertical positioning rod into the hole
located on the bottom, left side of the oven can.
• Place your rotisserie spit-rod with your meat
prepared between the two prongs on the
U-bracket, and swing into place on the right side
wall of the oven can.
• Place the broil pan directly beneath the meat.
• Close oven door
• Set the oven to Broil mode
• Press the rotisserie button on the left side of the
front panel which will activate the rotisserie motor.
16
NOTE: For Convection Rotisserie, simply follow the
same steps and first press the rotisserie button,
followed by the convection button.
NOTE: Rotisserie system is only available in the Precision
Series gas Self-Clean Ranges and NOT the Precision
Series standard non-self clean gas convection ranges.
NOTE: Rotisserie system can ONLY be used in the
Broil Mode, and not Bake mode.
INTERNAL COOKING TEMPERATURES
FOOD
OVEN TEMPERATURE
Egg and Egg Dishes
Eggs
Cook until yolk and
white are firm
Egg Casseroles
160 degree F
Egg Sauces, Custards
160 degree F
Ground Meat and Meat Mixtures
Turkey, Chicken
165 degree F
Beef, Veal, Lamb, Pork
160 degree F
Fresh Beef, Veal, Lamb
Medium Rare
145 degree F
Medium
160 degree F
Well Done
170 Degree F
Fresh Pork
Medium
160 degree F
Well Done
170 degree F
Roast Beef
Cooked Commercially
140 degree F
Vacuum Sealed
140 degree F
Ready to eat
140 degree F
Poultry
Chicken, Turkey-Whole
180 degree F
Chicken, Turkey-dark meat 180 degree F
Poultry-breast
170 degree F
Duck and Goose
180 degree F
Stuffing
Cooked alone or in bird
165 degree F
Sauces, Soups, Gravies, Marinades
Used with raw meat, poultry, or fish Bring to boil
Seafood
Fin Fish
Cook until opaque and
flakes easily with a fork
OVEN SELF-CLEANING
The self-cleaning oven of your new range features
pyrolytic self-cleaning. When set in the SELF-CLEAN
mode , the oven reaches a high temperature that
burns off the food soil.
When the oven is on for SELF-CLEAN, only the
RANGETOP burners may be used.
NOTE: Before turning oven to self-clean mode,
wipe up the excessive Food Soil. This will minimize
any excessive smoke or flames that may occur.
It is common to see smoke and/or flames during
the SELF-CLEAN cycle, depending on the content
and amount of soil remaining in the oven. If a flame
persists, turn off the oven and allow it to cool before
opening the door to wipe up the excessive food soil.
At the end of the SELF-CLEAN cycle, some gray ash
or burned residue may remain inside the oven. This
is a mineral deposit that does not burn or melt. The
amount of ash depends on how heavily soiled the
oven was before the oven was cleaned. If is easily
removed, once has cooled, using a clamp paper
towel, sponge, or cloth.
Wipe off any smoke residue that remains on the front
frame with Formula 409® or Fantastik®. If stain
remains, use a mild liquid cleanser. The amount of
smoke stain is directly related to the amount of food soil
left in the time of self-cleaning. Clean the oven often.
OVEN DOOR LOCK DURING SELF-CLEAN
When the clean cycle starts, the lock light turns on,
and the automatic door lock cycle begins. Do not
attempt to open the door when the lock light is on.
You can stop the cycle by turning to OFF position.
The lock light will turn off only after the oven has
cooled below 550°F, and the automatic door lock
has completed its cycle to the open position.
BEFORE SELF-CLEANING THE OVEN:
4Remove all utensils and racks.
USING YOUR OVEN/ SELF CLEAN MODE
4Clean the oven front frame and outer door edges. Wipe up large spill overs and grease. (see to the right)
4Be sure the light bulbs and glass covers are in place.
4Turn on the ventilator hood above the range and leave it on until after the oven has completed the self-clean cycle.
4Wipe out puddles of grease and any loose soil that can be easily removed.
4Remove any soil that is outside the door seal area. This appliance is designed to clean the oven interior and that portion of the door that is inside the oven. The outer edges of the door and the oven cavity are not in the cleaning zone.
WIPE THIS AREA CLEAN BEFORE SETTING THE OVEN TO SELF-CLEAN.
SETTING THE OVEN FOR SELF-CLEAN
1. Set Oven Control Knob to “CLEAN”.
• Cooling Blower turns on
• SELF-CLEAN Light turns on
• DOOR LOCK Light turns on immediately and
the door latch engages within 10 seconds of
setting Oven Knob to Self-Clean Mode.
• The door closing process takes approximately 60 seconds to complete, at which time the door becomes locked.
AT THE END OF THE CLEAN CYCLE
The Clean cycle takes 5 hours to complete.
The DOOR-LOCK light turns off once the cycle
has finished.
1. The door latch will open automatically after
the oven temperature falls below 550°F and the
automatic Door Lock completes its 60 sec, cycle
to the OPEN position.
2. Turn the Oven Control Knob to OFF. Wipe off
white ash residue with a damp cloth or sponge
before placing oven racks.
3. Replace the oven racks.
CAUTION: The interior of the oven will still be at
baking temperature when the lock light turns off
and the oven door can be opened. Use caution as
the oven may be hot enough to cause burns.
cool before starring to clean the rangetop. If you
wipe off any part of the rangetop while it is hot do
so carefully as using a wet sponge or cloth can
result in steam burns.
All stainless steel parts of the appliance can be
cleaned with hot soapy water, rinsed, dried and
buffed to a shine with a soft, heavy pile cloth. Make
sure you clean in the DIRECTION OF THE GRAIN
and never in circular motions as this may scratch
the stainless steel.
BURNER GRATES
When lifting the grates, be careful as they are heavy.
Place them on a protected surface, so they won’t
scratch the surface they are laid on.
WARNING: Be careful cleaning any part of this
appliance while hot.
When cleaning this range or range-top:
1. Always use the mildest cleaning procedure
first. Some brands of cleaners of the same type
are harsher than others, read their directions. A
scent or a propellant can make a difference in
the product. Read the ingredients. Try on a small
area first.
2. To avoid marring the surface always rub metal
finishes in the direction of the polish (grain)
lines. The cleaner will be more effective when
used in the direction of the polish lines.
3. Use only clean sponges, soft cloths, paper towels,
for cleaning or scouring (Use only soap pads
with soap still in them. An empty pad can
scratch), as recommended in this section.
4. Be sure to rinse all parts thoroughly and to wipe
dry to avoid water marks.
NOTE: BRAND NAMES - In this section on cleaning,
the use of name brands is intended only to indicate a
type of cleaner. This is not constitute an endorsement.
The omission of any name brand cleaner does not
imply its adequacy or inadequacy. Many products are
regional in distribution and can be found in the local
markets and department stores.
RANGETOP
Turn off all the burners and allow the grates to
The burner grates are matte porcelain enamel
over cast iron. When cool they may be placed in
the dishwasher, or wipe while on the rangetop
using hot soapy water, then rinsed and wiped dry.
The burner grates will not rust as they are matte
porcelain enamel on both sides for durability.
The occasional use of mild abrasive cleaners such
as Bon-Ami®, Soft Scrub®. Abrasive cleansers,
used vigorously or too often, can eventually harm
the enamel. Apply with a damp sponge, rinse
thoroughly and dry.
The porcelain may pop off the edge of the grates
due to rapid temperature change when the burners
are turned on, Do not be concerned as this does not
result in the deterioration of the grates. The cast iron
soon darkens to blend with the porcelain enamel. Be
careful when wiping an area where the porcelain has
popped off, as the edges may be sharp.
BURNERS
For proper lighting and performance keep the
burners clean. It is necessary to clean the burners
if they do not light even through the igniter clicks,
if there has been a severe boil over, or when the
flame does not burn blue.
Be certain all burner knobs are in the OFF position
before attempting to clean the burners. The burners
have been designed for ease in cleaning. When
the grates and burners are cool, remove the grate.
The Burner Cap and the Flame Ring can easily be
lifted off. Wash these parts in hot soapy water, rinse
and dry thoroughly. The Burner Caps are porcelain
enamel, follow the directions on the previous page
17
CARE AND MAINTENANCE
that were given for the burner grates. A bristle brush
can be used to clean out the toothed burner ports,
if necessary. Disassembly of the Simmer Ring is not
recommended, however, it may become necessary
to do so if the ports remain clogged after normal
cleaning. If it is necessary to disassemble the
Simmer Ring from the Base, remove the Hex Nut
at the top of the Simmer Ring. Clean the Simmer
Ring with hot soapy water using a soft wire or plastic
bristle brush then dry thoroughly. Re-assemble the
parts using the Hex Nut.
After cleaning, it is important to make sure the
Locating Notch at the bottom of the Simmer Ring
is properly aligned with the corresponding Mark in
the Base and that the Locating Marks in the Cap
are aligned with the marks in the Ring. Incorrect
alignment will produce a potentially dangerous
flame and poor burner performance.
replace these knobs on the correct gas valve on the
control panel.
LOW BACK, OR HIGH SHELF (IF INSTALLED)
Depending on the model, these are constructed of
either all stainless steel or a combination of stainless
steel and glass. Use the mildest cleaning procedure
first – hot soapy water, rinse and dry. If the panel has
food soil remaining, try a general kitchen cleaner,
such as Fantastik®, Simple Green®, or Formula
409®. For hard to clean soil use a stainless steel
cleaner such as, Bon-Ami®, Cameo®, or Bar
Keepers Friend. Apply cleaner with a damp sponge,
rinse thoroughly and dry. Always scrub lightly in the
direction of the grain. Do not use a steel wool pad,
it will scratch the surface. To touch up noticeable
scratches in the stainless steel, sand very lightly with
dry 100 grit emery paper, rubbing in the direction
of the grain. After cleaning use a stainless steel
polish, such as Stainless Steel Magic ® .
If the rear top burner are used extensively on high
it is possible for the vertical stainless steel panel to
discolor from the burner heat. This discoloration
can be removed by using Revere Ware Stainless
Steel Cleaner.
1. Burner Cap
2. Flame Ring
3. Beauty Ring
4. Burner Base
5. Igniter
6. Venturi
IGNITERS
Wipe with a water-dampened cotton swab. Be
careful not to damage the igniter. (See illustration).
CONTROL KNOBS - RANGETOP AND OVEN
These are made of die-cast metal with plastic inserts
for easier gripping. They can be cleaned in hot, soapy
water. To remove the Knobs from the control panel,
grasp the knob and pull straight forward. Wash, do
not soak. Rinse and dry thoroughly. It is important to
18
OVEN AND DOOR INTERIOR
If in the event the oven door comes off track, or
becomes misaligned, realignment can be achieved
by following this simple procedure:
Open the door and hold it all the way open. Close
the hinge latches. Once both hinges are locked,
gently lift the door up and partially out until the
door is evenly aligned. Evenly slide the door back
into place and check to assure the hinges rest in
the center of each door hinge roller. With the oven
door fully open, unlock hinge latches and the door
is ready to close again.
Be sure the oven and door are cool before you
start to clean them. They are porcelain enamel
coated. It is acid resistant, but not acid proof.
Therefore, acid foods, such as vinegar, rhubarb,
alcohol, citric juices or milk, should be wiped and
not allowed to brake on.
Try mild cleaners, such as: Bon-Ami®, ammonia,
ammonia and water, or Soft Scrub®. Apply the
powers on a damp sponge or cloth. Rub lightly.
Rinse thoroughly and dry. If food has burned onto
the oven and is difficult to remove, soak the spots
with a cloth saturated with household ammonia.
Allow it to soak for an hour or two, with the door
closed. The food soil should be easy to remove
with a damp soapy cloth or mild abrasive.
OVEN RACKS AND ROLLERS
The oven racks and rollers are chrome plated steel.
Chrome cleaners, such as Soft Scrub®, Cameo or
Bar Keepers Friend can be applied with a damp
sponge following package directions. Rinse and dry.
Powdered cleaners such as Bon-Ami® or Comet
are applied with a damp sponge or cloth, rubbed
lightly, rinsed and dried. Harsh Cleaners which
are commercial oven cleaners, such as Easy Off®
or Dow can be used on the racks. However, some
commercial oven cleaner’s cause darkening and
discoloration. Test the cleaner on a small part of the
rack and check for any discoloration before cleaning
the entire rack. Allow to stand for 15 to 20 minutes.
Rinse thoroughly and dry.
FRAMES, SIDES, DOOR EXTERIOR, HEAT DEFLECTOR
These parts are made of stainless steel, follow the
directions for the Backguard (see page 28). Take care
when cleaning the door top, and do not let water or
cleaners run down the vents. If water or cleaners spill
into the vents, they may streak the glass inside the door.
DOOR GASKET
Use a general kitchen spray cleaner, such as Formula
409® or Fantastik®. Spray it and blot dry with a cloth.
Do not rub. Do not remove or damage the mesh.
CARE AND MAINTENANCE / LOCATING RATING PLATE
OVEN LIGHT BULB REPLACEMENT
For oven light bulb replacement use only a 40 watt,
120 volt appliance light bulb. These are available in
supermarkets. DO NOT use a standard light bulb in
any oven, the heat will break it.
TO REPLACE THE LIGHT BULB:
1. Be sure the oven light bulb switch is the off
position The bottom of the switch is pressed in.
Let the cover and the bulb cool completely.
2. Remove the light cover, Turn the cover to the
left (counterclockwise) to unscrew it.
3. Remove the burnt out bulb. Replace it with a 40
watt appliance light bulb only.
4. Replace cover. Turn circuit breaker back on, if
turned off. (See Caution below).
CAUTION: Be sure the oven light switch (see page
8, # 11) is in the OFF position and the cover is
cool. If the bulb comes loose from the base, turn
off the power to the oven at the circuit breaker
panel, before attempting to remove the bulb base
from the socket.
POWER FAILURE
The broiler and oven burners cannot be turned
on during a power failure. To light the sealed top
burners, turn the control knob to “lite” hold a lighted
match to the port ring. After the flame is burning
all the way around the burner, adjust the flame to
the desired height. It is necessary to light each
burner individually. Do not light more than one
burner at a time.
LOCATING RATING PLATE
SERIAL #, MODEL # AND VERIFYING GAS TYPE
The rating plate contains necessary information
regarding your range. It provides the model #, serial
# and verifies the gas type and BTU input ratings
for each burner of your appliance. When calling for
service, please have this information at hand.
Model #, Serial #, and gas type location
Rating Plate w/ BTU ratings
The model#, serial # and gas type information is
located in two places. First, when you open the oven
door, you will find a sticker that shows the model #
followed by either an N (for natural gas) or L (for LP
gas), and the serial # (see picture).
Model #, Serial # and gas type location
The rating plate, showing the model #, serial #, gas
type and gas BTU input ratings for each burner, as
well as necessary information from ETL test labs,
is located behind the kick-plate. You will need to
remove the kick-plate to access this information
(see picture).
BTU ratings for each burner
19
TROUBLESHOOTING
RANGES AND RANGE-TOPS
PROBLEM
POSSIBLE CAUSE
PROPOSED SOLUTION
Range non-functional
No electricity or gas supply
Turn on gas supply valve
Check circuit breakers
One or more burners will not light
Incorrect flame/ sooty burner flame
BBQ-GRILL doesn’t light
20
Technical
Call for authorized service
No electricity
Check circuit breakers
No gas
Check gas supply at wall
Wrong gas type
Verify gas type
Burners are dirty
Clean burners
Burners are mis-aligned
Align and reassemble burners
Water in burner(s)
Dis-assemble and dry burners
Dirty electrode(s)
Clean burner electrode
Technical
Call for authorized service
Too large or small
Verify gas type
Mis-aligned burner assembly
Realign and re-assemble burner assembly
No Electricity
Check circuit breaker
No gas
Check gas supply at wall
Burner is dirty
Clean burner
TROUBLESHOOTING
RANGE OVENS
PROBLEM
POSSIBLE CAUSE
PROPOSED SOLUTION
No oven light
No electricity
Check circuit breakers
Check plug at wall
No oven heat (bake)
Loose bulb
Ensure bulb is properly screwed in
Burned out bulb
Replace bulb
No gas
Check for proper top burner operation
No electricity (check oven light)
Check circuit breakers
Check plug
Improper settings
Verify proper settings on knob selector
No oven broil
Improper settings (see no bake)
Verify proper settings
Uneven baking
Insufficient pre-heat time
Allow oven to preheat at least 15 minutes before baking
Improper settings
Verify proper settings on knob selector
Improper utensils/placement
Use proper utensils and place them properly in the
proper rack positions
No convection
No convection fan
Check for air movement
Convection noisy
Technical
Call for authorized service
Rotisserie not working
Rotisserie rod not firmly in place
Place rod firmly in rotisserie location hole
Rotisserie noisy
Technical
Call for authorized service
21
INSTALLATION INSTRUCTIONS
PRECISION SERIES Ranges
SELF CLEAN GAS CONVECTION MODELS:
GSCR30 (4Q, 4G, 5)
GSCR36 (4Q, 4G, 4W, 6)
GSCR48 (4G, 4W, 4QG, 6Q, 6G, 8)
GSCR60 (4QG,4QW, 4GW, 6QG, 6G, 6W)
MANUAL CLEAN GAS CONVECTION MODELS:
GCR30 (4, 5)
GCR36 (4B, 4G, 6)
GCR48 (4G, 4W, 4BG, 6B, 6G, 8)
22
TABLE OF CONTENTS
Important Information
25
30” - All Models
26
36” - All Models
27
48” - All Models
28
60” - All Models
29
Unpacking and Ventilation Requirements
30
Cabinet Preparation
31
Cabinet Install Drawing / Front View
32
Cabinet Install Drawing / Side View
33
Installation Instructions
34
Gas Hook-Up / Testing and Adjustments
36
Post-Install Check
37
Service & Warranty Info
38
23
IMPORTANT INFORMATION
PLEASE READ ENTIRE
INSTRUCTIONS
BEFORE PROCEEDING.
WARNING! Disconnect Power before installing.
Before turning power ON, be sure that all controls
are in the OFF position.
WARNING! If the information in this manual is
not followed exactly, a fire or explosion may
result causing property damage, personal injury
or death.
IMPORTANT INSTALLATION INSTRUCTIONS
INTRODUCTION
Capital’s PRECISION Series Gas Ranges are tested
and approved in accordance with ANSI Z21.1b-2003/
CGA IR 58, 1995, Household Cooking Appliances. It
is STRONGLY RECOMMENDED that this appliance be
installed in conjunction with a suitable overhead VENT
HOOD. Due to the high heat output of this unit, particular
attention should be paid to the hood and ductwork
installation to assure it meets local building codes.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance
• Do not touch any electrical switch
• Do not use any phone in your building
• Immediately call your gas supplier from a neighbors
phone. Follow the gas supplier’s instructions.
• If you can not reach your gas supplier, call the fire department.
IMPORTANT: Save these instructions for the Local
Gas Inspector’s use.
INSTALLER: Please leave these Installation
Instructions with the unit for the owner.
OWNER: Please retain these instructions for future
reference.
The appliance, when installed, must be electrically
grounded in accordance with local codes or, in the
absence of local codes, with the National Electrical
Code, ANSI/NFPA 70
The appliance and its individual shutoff valve must
be disconnected from the gas supply piping system
during any pressure testing of that system at test
pressures in excess of 5 psi (35 kPa).
The appliance must be isolated from the gas supply
piping system by closing its individual manual
shutoff valve during any pressure testing of the gas
supply piping system at test pressures equal to or
less than 5 psi (35 kpa).
24
IMPORTANT! Installation must conform with local codes.
NOTE: Local building codes vary. Cabinet storage
above the unit should be avoided to prevent the
risk of accidental fire or burns.
In the commonwealth of massachusetts, gas
connection must be performed by a licensed
plumber or gas fitter.
IMPORTANT! Installation, electrical connections,
grounding and gas connections must comply with
all applicable codes. In the absence of local codes,
the unit should be installed in accordance with the
National Fuel Gas Code ANSI Z223.1/NFPA54CURRENT ISSUE and National Electrical Code
ANSI/NFPA70-CURRENT ISSUE.
Be sure the unit being installed is set up for the
type of gas supplied. The Gas range shipped from
the factory is set for Natural Gas or LP (Propane),
depending on the specific model ordered.
ENSURE THAT THE RANGE IS COMPATIBLE WITH
GAS SUPPLY AT THE INSTALLATION SITE BEFORE
PROCEEDING FURTHER. Contact the unit to
the dealer if it is not set for the proper gas supply
available at the installation site.
IMPORTANT! A back guard must be utilized when
there is less than 12” horizontal clearance between
combustible materials and the back edge of the
range. The Capital PRECISION SERIES Low Back or
High Shelf must be ordered separately and installed
at the rear of the range. For island installations and
other installations with more than 12” clearance, our
stainless steel Island Trim is suitable to cover the
back guard mounting flanges.
GAS SUPPLY
NATURAL GAS: 6-inch water column. (14.9mb)
Min., 8 inch (20mb) nominal
PROPANE GAS: 11-inch water column. (27.4mb),
14 inch (37mb) maximum
ELECTRIC POWER SUPPLY
GSCR30, GCR30 models – 120 VAC, 60 HZ, 1 PH.,
20 Amp Circuit
GSCR36, GCR36 models – 120 VAC, 60 HZ, 1 PH.,
20 Amp Circuit
GSCR48, GCR48 models – 120 VAC, 60 HZ, 1 PH.,
20 Amp Circuit
GSCR60 Models 120 VAC, 60 HZ, 1 PH, 20 Amp
STEP 1: UNPACKING, MOVING and PLACING the
RANGE
CAUTION: Proper equipment and adequate
manpower must be used in moving the range to
avoid damage to the unit or the floor. The unit is
heavy and rests on stainless steel legs.
•It is strongly recommended that after removing the
packing material, remove the door(s), top grates,
oven racks, front kick plate and drip pan(s) to
facilitate lifting and easier handling.
•Remove the outer carton and packing materials
from the shipping base. The all gas ranges are held to
the skid by three (3) bolts. After removing the bolts
the range must be lifted and removed from the skid.
30” - ALL MODELS
GCR304 - 4 Burner Gas Convection range
GSCR304G - 4 Burner Gas Self Clean Range w/ 9” Thermo-Griddle
GSCR305 - 5 Burner Gas Self Clean Range w/ Wok Burner
GCR305 - 5 Burner Gas Convection Range w/ Wok Burner
GRT305 - 5 Burner Gas Range Top w/ Wok Burner
GSCR304Q - 4 Burner Gas Self Clean Range w/ 9” Infra-BBQ
Note: 304 = 19K BTU Power-Flo Burners • 305 = 19K BTU Power Flo + 25K BTU Power-Wok • 304Q = 15K BTU Power-Flo Burners + 15K BTU Infra-BBQ
304G = 15K BTU Power-Flo + 15K BTU Thermo-Griddle
25
36” ALL MODELS
GSCR366 -- 6 Burner Gas Self Clean Range
GSCR364W -- 4 Burner Gas Self Clean Range w/ Wok
GCR366 -- 6 Burner Gas Convection Range
GRT364W -- 4 Burner Gas RangeTop w/ Wok
GRT366 -- 6 Burner Gas RangeTop
Note:
366 = 19K BTU Power-Flo Burners
364W = 15K BTU Power Flo + 30K BTU Power-Wok
364Q = 19K BTU Power-Flo Burners + 18K BTU Infra-BBQ
364G = 19K BTU Power-Flo + 18K BTU Thermo-Griddle
364B = 19K BTU power-Flo Burners + 18K BTU Tru-Q Stainless Steel BBQ-Grill
GSCR364G -- 4 Burner Gas Self Clean Range w/ 12” Griddle
GCR364G -- 4 Burner Gas Convection Range w/ 12” Griddle
GRT364G -- 4 Burner Gas RangeTop w/ 12” Griddle
GSCR364Q -- 4 Burner Gas Self Clean Range w/ 12” Infra-BBQ
GCR364B -- 4 Burner Gas Convection Range w/ 12” SS-BBQ
GRT364Q -- 4 Burner Gas RangeTop w/ 12” Infra-BBQ
26
48” ALL MODELS
GSCR484G - 4 Burner Gas Self Clean Range w/24” Griddle
GSCR486Q - 6 Burner Gas Self Clean Range w/12” Infra-BBQ
GCR484G - 4 Burner Gas Convection Range w/ 24” Griddle
GCR486B - 6 Burner Gas Convection Range w/ 12” SS-BBQ
GRT484G - 4 Burner Gas RangeTop w/ 24” Griddle
GRT486Q- 6 Burner Gas RangeTop w/ 12” Infra-BBQ
GSCR484W - 4 Burner Gas Self Clean Range w/24” Wok
GSCR484QG - 4 Burner Gas Self Clean Range w/12” Infra-BBQ + 12” Griddle
GCR484W - 4 Burner Gas Convection Range w/ 24” Wok
GCR484BG - 4 Burner Gas Convection Range w/ 12” SS-BBQ + 12” Griddle
GRT484W - 4 Burner Gas RangeTop w/ 24” Wok
GRT484QG- 4 Burner Gas RangeTop w/ 12” Infra-BBQ + 12” Griddle
GSCR486G - 6 Burner Gas Self Clean Range w/12” Griddle
GSCR488 - 8 Burner Gas Self Clean Range
GCR486G - 6 Burner Gas Convection Range w/ 12” Griddle
GCR488 - 8 Burner Gas Convection Range
GRT486G - 6 Burner Gas RangeTop w/ 12” Griddle
GRT488 - 8 Burner Gas Range-Top
Note:
*19K BTU Power-Flo Burners • 30K BTU Power-Wok • 30K BTU 24” Thermo-Griddle • 18K BTU 12” Infra-BBQ • 18K BTU 12” Thermo-Griddle
* 18K BTU 12” Tru-Q SS BBQ-Grill
27
60” ALL MODELS
GSCR604GW -- 4 Burner Gas Self Clean Range w/12” Griddle + 24” Wok
GSCR604QG -- 4 Burner Gas Self Clean Range w/12” Infra-BBQ + 24” Griddle
GRT604GW -- 4 Burner Gas RangeTop w/12” Griddle + 24” Wok
GRT604QG -- 4 Burner Gas RangeTop w/12” Infra-BBQ + 24” Griddle
GSCR604QW -- 4 Burner Gas Self Clean Range w/12” Infra-BBQ + 24” Wok
GSCR606G -- 6 Burner Gas Self Clean Range w/24” Griddle
GRT604QW -- 4 Burner Gas RangeTop w/12” Infra-BBQ + 24” Wok
GRT606G -- 6 Burner Gas RangeTop w/24” Griddle
GSCR606W -- 6 Burner Gas Self Clean Range w/24’ Wok
GSCR606QG -- 6 Burner Gas Self Clean Range w/12” Infra-BBQ + 24” Griddle
GRT606W -- 6 Burner Gas RangeTop w/24” Wok
GRT606QG -- 6 Burner Gas RangeTop w/12” Infra-BBQ + 24” Griddle
Note: 19K BTU Power-Flo Burners • 30K BTU Power-Wok • 30K BTU 24” Thermo-Griddle • 18K BTU 12” Infra-BBQ • 18K BTU 12” Thermo-Griddle
28
UNPACKING AND VENTILATION REQUIREMENTS
• Lift the range from the skid with a soft wheel dolly.
• Support the range uniformly across the bottom
surface. Where space permits, a hood larger in
width than the cooking surface may be desirable for
improved ventilation performance.
• To remove door, open the door completely, close
the hinge latches and release the door. Remove
door by lifting and pulling.
VENTILATION UNIT
STANDARD COUNTER
INSTALLATION
RECOMMENDATIONS
• Make sure gas and electric connections are made,
anti-tip device is installed, and the back guard
installed prior to placing the range in position.
HOOD
(24” DEEP X UNIT WIDTH)
• Measure the height of the counter top and adjust
the range height to match countertop height by
adjusting front and rear leveling feet.
• Slide the range in place and ensure that the range
is level.
• Reinstall the kick plate, top grates, oven door(s),
drip pan tray(s), and make sure burner caps are
seated firmly and locked into position.
WARNING: DO NOT lift the range by the oven door
handles. Do not remove the griddle and grill sections!
STEP 2: VENTILATION REQUIREMENTS
It is strongly recommended that a suitable exhaust
hood be installed above the range. Downdraft ventilation
should NOT be used. The table below indicates the
PRECISION Series Hoods, by model number, that are
recommended for use with all ranges.
1. SELECT HOOD AND BLOWER MODELS:
SIZE
30”
36”
48”
60”
SHIPPING WEIGHT
350
450-550
595-695
700-850
For wall installations, the hood width must, at a
minimum, equal the width of the range’s cooking
BLOWER CFM’s
60” RANGE = 1200 CFM
48” RANGE = 600-1200 CFM
36” RANGE = 600-1200 CFM
30” RANGE = 600 CFM
CAUTION: Ventilation hoods and blowers are
designed for use with single wall ducting.
However, some local building codes or inspectors
may require double wall ducting. Consult local
building codes and/or local agencies, before
starting, to assure that hood and duct installation
will meet local requirements.
Hood blower speeds should be variable to reduce
noise and loss of heated or air-conditioned
household air when maximum ventilation is not
required. Normally the maximum blower speed is
only required when using the grill section.
2. HOOD PLACEMENT:
For best smoke elimination, the lower edge of the
hood should be installed a minimum of 30” to a
maximum of 36” above the range cooking surface.
If the hood contains any combustible materials (i.e.
wood covering), it must be a minimum of 40” above
the cooking surface.
STEP 3: CABINET PREPARATION
1.The range is a freestanding unit. If the unit is
to be placed adjacent to cabinets, the clearances
shown in fig. 1 are required. The same clearances
apply to island installations, except for the
overhead cabinets, which must have a space wide
enough to accept a suitable flared island hood, as
indicated in fig. 1. Note: Capital Cooking does
NOT offer an island style ventilation hood.
2.The maximum depth of overhead cabinets
installed on either side of the hood is 13”.
3. A 40-inch minimum clearance is required between
the top of the range and the bottom of an
unprotected cabinet. A 30-inch minimum distance
is necessary when the bottom of the wood or
metal cabinet is protected by not less than 1/4
inch of a flame retardant material covered with
no less than No. 28 MSG Sheet Steel, 0.015-inch
(0.4 mm) thick stainless steel, 0.024-inch (0.6
mm) aluminum, or 0.020 inch (0.5 mm) thick
copper. Flame retardant materials bear the mark:
UNDERWRITERS LABORATORIES INC.
Classified Mineral and Fiber Boards
Surface Burning Characteristics
Followed by the flame spread and smoke ratings.
These designations are shown as “FHC (Flame
Spread/Smoke Developed).” Materials with “O”
flame spread ratings are flame retardant. Local
codes may allow other flame spread ratings.
4.Any openings in the wall behind the range and in
the floor under the range must be sealed.
5.W hen there is less than a 12” horizontal
clearance between combustible material D and
the back edge of the range above the cooking
surface, a Capital Low Back or High Shelf
back guard must be installed (see Fig. 2A).
When clearance to combustible material D is
over 12”, a Capital Island Trim may be used
(See Fig. 2B). Figures 2A and 2B indicate the
space required for each type of back guard.
6.Always keep appliance are clear and free from
29
UNPACKING AND VENTILATION REQUIREMENTS
combustible materials, gasoline,
flammable vapors and liquids.
and
other
7.Models with open char broiler, noncombustible
material is to be installed on the underside of a
cabinet located above the broiler section or unit in
accordance with local codes, or in the absence of
local codes, with the National Fuel Gas code, ANSI
Z223.1/NFPA 54.
WARNING: DO NOT obstruct the flow of combustion
and ventilation air to the unit.
PLEASE NOTE:
In the Commonwealth of Massachusetts, gas
connection must be performed by a licensed
plumber or licensed gas fitter.
30
CABINET INSTALL DRAWING / FRONT VIEW
FIG 1A. Cabinet Clearances:
31
CABINET INSTALL DRAWING / SIDE VIEW
FIG 2A Side View:
32
INSTALLATION INSTRUCTIONS
WALL MOUNT BACKGUARD INSTALLATION
NOTE: ALL PRECISION SERIES RANGES come
with an island trim.
• Secure the back guard (19” High Shelf, or 9” Low
Back) directly on the wall behind range and
above the factory installed island trim. DO NOT
REMOVE the island trim. It is necessary for proper
venting of the oven gases/heat.
BACKGUARD MOUNTING:
WALL MOUNT HIGH SHELF
1. First measure from top of island trim to 16 3/8”
to what will be the center of the mounting
brackets. (see Fig 1)
2. Secure both brackets to the wall using the
screws included.
3. Slide shelf into position and over brackets.
ELECTRICAL SUPPLY, ALL RANGES
Installation of All Precision ranges must be
planned so that the rough-in of the junction box
for the receptacle or conduit connection allows for
maximum clearance to the rear of the unit.
This is especially critical if the junction box in the
wall will be directly behind the junction box of the
unit when the unit is installed. To minimize binding
when the unit is connected to the receptacle or
junction box, orient the receptacle or conduit
connector, and slide back into position.
2. Secure both brackets to the wall using the
screws included.
3. Attach the shelf to the shelf support panels with
supplied screws.
4. Slide shelf into position and over brackets.
BACKGUARD MOUNTING:
WALL MOUNT LOW BACK
1. First measure from top of island trim to 16 3/8”
to what will be the center of the mounting
brackets. (see Fig 1)
POWER REQUIREMENTS: 120 VAC, 60 HZ single phase
• 24” Range – 4 Amps. Max.
• 30” Range – 7 Amps. Max.
• 36” Range – 7 Amps. Max.
• 48” Range – 13 Amps. Max.
• 60” Range – 13 Amps. Max
CAUTION! Disconnect the electrical supply cord
from the wall outlet before servicing the range.
Follow all governing codes and ordinances when
grounding. In the absence of codes follow the
National Electrical Codes ANSI / NFPA No. 70
(current issue).
GROUNDING METHOD
The range is factory fitted with a power supply and
cord with a three-prong grounding plug. It must be
plugged into a matching grounding type receptacle
connected to a correctly polarized 120 Volt
circuit. If the circuit does not have a grounding type
receptacle, it is the responsibility of the installer to
have the existing receptacle changed to a properly
grounded and polarized receptacle in accordance
with all applicable local codes and ordinances. The
receptacle replacement shall be in accordance with
the national Electrical Code.
WARNING! The third prong SHOULD NOT, under
any circumstances, be cut or removed!
33
INSTALLATION INSTRUCTIONS
STEP 4: INSTALLING ANTI-TIP DEVICE
For all Ranges, an anti-tip device MUST be installed
as per these instructions.
WARNING!
• ALL RANGES CAN TIP
• INJURY TO PERSONS COULD RESULT
• INSTALL ANTI-TIP DEVICES PACKED WITH RANGE
• SEE INSTALLATION INSTRUCTION
WARNING: RANGE TIPPING HAZARD!
• All ranges can tip and injury can result. To prevent
accidental tipping of the range, attach it to the
floor, wall or cabinet by installing the Anti-Tip
Device supplied.
• A risk of tip-over may exist if the appliance is not
installed in accordance with these instructions.
• If the range is pulled away from the wall for
cleaning, service or any other reason, ensure that
the Anti-Tip Device is properly re-engaged when
the range is pushed back against the wall. In
the event of abnormal usage (such as a person
standing, sitting, or leaning on an open door),
failure to take this precaution can result in tipping
of the range. Personal injury might result from
spilled hot liquids or from the range itself.
WARNING: ELECTRICAL SHOCK HAZARD!
• Use extreme caution when drilling holes into the
wall or floor. There may be concealed electrical
wires located behind the wall or under the floor.
• Identify the electrical circuits that could be affected
by the installation of the Anti-Tip Device, then turn
off power to these circuits.
34
• Failure to follow these instructions may result in
electrical shock or other personal injury.
• The thickness of the wall or floor may require use of
longer screws, available at your local hardware store.
CAUTION: PROPERTY DAMAGE!
• Contact a qualified installer or contractor to
determine the proper method for drilling holes
through the wall or floor material (such as ceramic
tile, hardwood, marble, etc.)
• In all cases at least one (1) of the bracket mounting
screws must be fastened to solid wood or metal
on each side.
• DO NOT slide range across unprotected floor.
• Failure to follow these instructions may result in
damage to wall or floor coverings.
TOOLS NEEDED FOR INSTALLATION OF
ANTI-TIP DEVICE!
1. Screwdriver, Phillips
2. Drill, electric or hand
3. Measuring tape or ruler
4. 1/8” drill bit (wood or metal wall or floor)
5. 3/16” anchors, drywall, or concrete, 2 each (not required if mounting bracket is being attached to solid wood or metal.
6. Hammer
7. Pencil or other marker
IMPORTANT INSTALLATION INFORMATION
• The Anti-Tip Bracket may be attached to a solid
wood cabinet having a minimum wall thickness of 3/4”.
• Use appropriate anchors when fastening the
mounting bracket to any material other than
hardwood or metal.
MOUNTING ANTI-TIP BRACKET:
The alternative floor mounted bracket shall be
installed as follows:
• Place bracket on floor in position shown in Figure below.
• Secure to floor or wall stud.
• Later, when unit is installed, the adjustable leg will
slide under the bracket
STEP 5: GAS CONNECTION AND HOOK-UP
Verify the type of gas being used at the installation
site matches the gas type of the range. As shipped
from the factory, units are configured for use with
Natural Gas or Propane (LP). Make certain the range
matches the type of gas available at this location.
For installation of the appliance at high altitude,
please consult your local gas company for their
recommendation of the correct orifice sizes and any
other necessary adjustments that will provide proper
gas combustion at specified altitudes.
ANTI-TIP BRACKET
MODEL
30”
36”
48”
60”
A
14-15/16”
17-15/16”
23-15/16”
24-15/16”
THIS SIDE
AGAINST WALL
NOTE: Capital DOES NOT supply ranges to match
varying altitudes. Orifices to adjust for combustion
for differing altitudes may be purchased through
Capital Cooking Equipment by calling our Parts
Department at 1-866-402-4600, or email us at
customerservice@capital-cooking.com.
GAS HOOK-UP / TESTING AND ADJUSTMENTS
CAUTION! When connecting unit to Propane (LP)
gas, make certain the propane tank is equipped
with its own high-pressure regulator in addition to
the pressure regulator supplied with the appliance.
The pressure of the gas supplied to the appliance
regulator must not exceed 14” (37 mb) water
column.
NATURAL GAS REQUIREMENTS:
• Inlet Connection: 1/2” N.P.T.
• Min. 5/8” Dia. Flex Line.
• Supply Pressure: 6” to 14” W.C.
PROPANE (LP) GAS REQUIREMENTS:
• Inlet Connection: 1/2” N.P.T.
• Min. 5/8” Dia. Flex Line.
• Supply Pressure: 11” to 14” W.C.
• A Regulator is required at the LP source to provide
a maximum of 14” W.C. pressure to the range
regulator.
WARNING! Gas line cannot be run inside back
cover of range. Run gas line in channel in back
of range.
HOOK UP
• A manual shut off valve must be installed external
to the range in an accessible location from the front
for shutting off the gas supply when required.
• The supply line MUST NOT protrude beyond the
back of the range.
• Ensure that the gas supply is turned OFF at the
external shut-off valve before connecting the range.
• The gas supply connection must be made by an
experienced technician and in accordance with
local codes or ordinances. In the absence of local
codes or ordinances, please refer to National Fuel
Gas Code ANSI Z223.1 / NFPA54-Current Issue.
• The range is supplied with its own pressure regulator
that has been permanently mounted with the range body.
• Use 5/8” diameter flex line to connect between the
gas supply and the appliance manifold pipe, which
exists at the upper left rear of the appliance. The
appliance manifold pipe connection is 1/2”. Use
caution to avoid crimping the 5/8” flex line.
• NOTE: the flex line for the gas supply must be metal
and approved by an approved certifying agency
(AGA, CGA, CSA, UL or CUL). NEVER use a hose
made of rubber or other synthetic material as the
heat may cause the hose to melt and develop leaks,
thus causing fires, physical and property damage.
• Always use pipe dope or Teflon ® tape on the
pipe threads, and be careful not to apply excessive
pressure when tightening the fittings.
• Leak testing of the appliance shall be in accordance
with the manufacturer’s instructions.
• Turn on gas and check supply line connections for
leaks using a soap solution. Do not use a flame of
any sort to test for leaks.
CAUTION! The appliance must be isolated from the
gas supply piping system by closing its individual
manual shut-off valve during any pressure testing
of the gas supply piping system at test pressures
equal to or less than 1/2 psig (3.5kPa.).
The Appliance and its individual shut off valve
must be disconnected from the gas supply piping
system during any pressure testing of the system
at test pressures in excess of 1/2 psig (3.5kPa.).
When checking the manifold gas pressure, the inlet
pressure to the regulator should be at least 6.0”.
DO NOT attempt any adjustment of the pressure
regulator.
TESTING AND ADJUSTMENTS
Install any loose components, such as burner caps
and grates, oven racks that may have been removed
earlier to facilitate moving the appliance. Be certain
that burner caps seat properly into the alignment
slots in the burner bases. Before testing operation
of the appliance, verify that the unit and the gas
supply have been carefully checked for leaks and
that the unit has been connected to the electrical
power supply. Turn the manual gas shut-off valve to
the open position. Check the operation of the sealed
gas burners and grill by pushing and turning each
knob counterclockwise to “HI”. The burner igniters
will click until the flame ignites.
Burner flames should be BLUE and stable with
no yellow tips, excessive noise, or lifting of the
flame from the burner. If any of these conditions
exist, check that the air shutter (grill and griddle
only) or burner ports are not blocked or clogged.
Remove any blockages that exist. If the flame is too
yellow, indicating insufficient air, adjust the shutter
counterclockwise to increase air inlet (grill and
griddle only).
The sealed top burner flames should be
approximately 1” to 1-1/4” High. The griddle and
grill flames should be as shown in the figure below.
CAUTION! A qualified technician must make
burner adjustments at the time of installation.
Improper or lack of adjustments may cause harmful
by-products or void your warranty!
35
P O S T- I N S TA L L C H E C K
NOTE: NO air shutter adjustment is necessary or
possible with the sealed top burners.
NOTE: If the sealed burners do not ignite and
there is NO clicking sound, turn OFF the gas and
check for tripped circuit breakers, blown fuse or
wire connection to the igniter.
INSTALLER CHECKLIST
FINAL CHECKLIST
qPlacement of unit
qSpecified clearances maintained to cabinet surfaces
qUnit Level – front to back – side to side
qBurner caps positioned properly on sealed burner bases
qAll packing materials removed
qIsland trim or back guard attached (if horizontal
clearance to combustible materials behind
cooking surface is less than 12”)
qCheck door adjustment and hold down brackets
GAS SUPPLY
qConnection: 1/2” NPT with a minimum of 5/8”
diameter flex line
qThe appliance is connected only to the type of gas
for which it is certified for use
qManual gas shut-off valve installed in an accessible
location (without requiring removal of range)
qUnit tested and free of gas leaks
qGas supply pressure does not exceed 14” (37 mb) W.C.
36
ELECTRICAL
qReceptacle with correct over current protection is
provided for service cord connection
qProper ground connection
qProper polarity at receptacle
qKick panel in place and 3 screws secure.
OPERATION
qAll internal packing materials removed. Check
below grates and grill pans and within ovens
qIf used on Propane gas, verify that the propane
gas supply is equipped with its own high-pressure
regulator in addition to the pressure regulator
supplied with appliance.
qBurner caps properly seated into burner bases.
qGrill Components properly seated (not all models).
qBezels centered on burner knobs and knobs turn freely.
q Each burner lights satisfactorily, both individually
and with other burners operating
q Air shutter adjustment for proper flame made for
Grill and Griddle sections.
q Griddle is level and does not rock.
q Oven door hinges seated and hinge locks in proper
position. Door opens and closes properly.
q Burner grates correctly positioned, level and do
not rock.
Note to Customer:
Please make sure installer signs each item on this
checklist, explains each item before leaving.
SERVICE & WARRANTY INFO
SERVICE INFORMATION
If none of the above has occurred, contact our
customer service department at 1-866-402-4600.
Before you call for service, please have the following
information available:
• Model #
• Serial #
• Date of Installation
• Copy of Receipt or Invoice
• A brief description of the problem
Your satisfaction is our top priority. If the problem
persists, or is not resolved to your satisfaction by
our service consultant, please write to us or fax us
a letter at:
Capital Cooking Equipment, Inc.
Attn: Customer Service Manager
13211 E. Florence Ave
Santa Fe Springs, CA
90670
USA
Fax #: 562-903-1167
Email: customerservice@capital-cooking.com
WARRANTY
•TWO (2) years full parts and labor covers the
entire product.
•Five (5) years parts and two (2) years labor,
on all Burners: Oven, Broiler, Stainless BBQ burner,
Griddle Burners, Sealed Burners, Wok Burner,
Infra-BBQ burner.
•Five (5) years parts on Burner Grates, Grill Grates,
Griddle Plate and Porcelain Enameled Parts.
• Lifetime parts and two (2) years labor against rust
on all stainless steel panels and components.
WILL PAY FOR:
All repair labor and parts found to be defective due
to material or workmanship for two (2) full years “IN
HOME” warranty. This does not apply if the unit
was subjected to other than normal household use.
An Authorized Factory Agent must provide service
during normal working hours. No charges will be
made for repair or replacement at the location of
original installation. No charges will be made for
defective factory parts returned pre-paid, through
the dealer, and claimed within the warranty period.
All claims, regardless of warranty or non-warranty
must be documented with photos and detailed
description and/or narrative of the problem and
submitted to Capital’s service department.
Replacement of parts will be freight prepaid by
Capital and shipped regular ground. Any requests
for other than standard ground shipments must
be paid by customer. The company will not be
liable for additional transportation costs, labor
cost, taxes or export/import duties. This warranty
shall not apply, nor can we assume responsibility
for damage that might result from failure to follow
manufacturer’s instructions or local codes where
the appliance has been tempered with or altered
in any way or which, in our judgment, has been
subjected to misuse, negligence, or accident.
Implied warranty shall not extend beyond the
duration of this written warranty. This warranty is
in lieu of all warranties, expressed or implied and
all other obligations or liability in connection with
the sale of this product.
WILL NOT PAY FOR:
• Installation or start-up.
•Shipping damage that is not a direct result of
packaging (for example freight handling).
•Service by an unauthorized agency.
• Use of unauthorized parts.
• Service during hours other than normal working hours.
• Improper installation.
•Service visit to teach you how to operate the appliance,
correct the installation, reset circuit breakers or
replace fuses.
• Repair other than normal household use.
•Damage caused by accident, abuse, alteration,
misuse, incorrect installation or installation not in
accordance with local codes.
• Unit(s) installed in non-residential applications.
This warranty applies to appliances used in
residential application only. It does not cover their
use in commercial situations. This warranty is for
products purchased and retained in the 50 States of
the U.S.A, the District of Columbia and Canada. This
warranty applies even if you should move during the
warranty period. Should the original purchaser sell
the appliance during the warranty period, the new
owner continues to be protected until the expiration
date of the original purchaser’s warranty period. This
warranty gives you the specific legal rights. You may also
have other rights, which vary from State to State.
Capital E.S.P. (Extended Service Plan) may be purchased
at an additional cost. Call us at 866-402-4600 for details.
37
NOTES
38
NOTES
39
DESIGN YOUR DREAM KITCHEN
40
ALL SPECIFICATIONS ARE FOR PLANNING PURPOSES ONLY. REFER TO INSTALLATION INSTRUCTIONS
AND CONSULT YOUR COUNTERTOP SUPPLIER PRIOR TO MAKING COUNTER OPENING. IF YOU HAVE
ANY QUESTIONS, PLEASE CALL US AT 866-402-4600 PRIOR TO CUTTING ANY OPENINGS. CONSULT
WITH A HEATING AND VENTILATING ENGINEER FOR YOUR SPECIFIC VENTILATION REQUIREMENTS.
FOR THE MOST UP TO DATE USE AND CARE AND INSTALLATION INSTRUCTIONS CONTACT
CAPITAL COOKING EQUIPMENT, INC. INDICATING THE MODEL #.
DUE TO ONGOING PRODUCT IMPROVEMENTS, WE RESERVE THE RIGHT
TO CHANGE THESE SPECIFICATIONS, OR DESIGNS WITHOUT NOTICE.
CERTIFIED FOR USA AND CANADA
T H E A RT O F P R E C I S I O N ™
13211 E. Florence Ave. Santa Fe Springs, CA 90670.
Toll Free: 866-402-4600
Main: 562-903-1168
Fax: 562-903-1167
Email: customerservice@capital-cooking.com
Website: www.capital-cooking.com.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising