Delfield CTP8146-NB Installation manual

Delfield CTP8146-NB Installation manual
18600 Series and CTP-NB
Service and Installation Manual
Please read this manual completely before attempting to install or operate this equipment! Notify carrier of damage! Inspect all
components immediately.
18600PTL
18600PTBM
Pizza Tables with LiquiTec® Rail
Pizza Tables with Raised Rail
18600PDL
®
Work Table with Backsplash
Dual LiquiTec
CAUTION
Rail Prep Table
18600BSTM
Important Information
Read Before Use
Please Save These Instructions!
18600BUCM
Work Tables
CTP-NB
Countertop Condiment Rail
May 2013
18600 and CTP-NB Series Service and Installation Manual
Important Warning And Safety Information
WARNING
Read This Manual Thoroughly Before Operating, Installing, Or Performing Maintenance On The Equipment.
WARNING
Failure To Follow Instructions In This Manual Can Cause Property Damage, Injury Or Death.
WARNING
Do Not Store Or Use Gasoline Or Other Flammable Vapors Or Liquids In The Vicinity Of This Or Any Other
Appliance.
WARNING
Unless All Cover And Access Panels Are In Place And Properly Secured, Do Not Operate This Equipment.
WARNING
This Appliance Is Not Intended For Use By Persons Who Lack Experience Or Knowledge, Unless They Have
Been Given Supervision Or Instruction Concerning Use Of The Appliance By A Person Responsible For Their
Safety.
WARNING
This Appliance Is Not To Be Played With.
Warning
Do Not Clean With Water Jet.
WARNING
Do Not Use Electrical Appliances Inside The Food Storage Compartment Of This Appliance.
CAUTION
Observe the following:
2
•
Minimum clearances must be maintained from all walls and combustible materials.
•
Keep the equipment area free and clear of combustible material.
•
Allow adequate clearance for air openings.
•
Operate equipment only on the type of electricity indicated on the specification plate.
•
Unplug the unit before making any repairs.
•
Retain this manual for future reference.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
18600 and CTP-NB Series Service and Installation Manual
Contents
Receiving & Inspecting Equipment............................................ 3
Serial Number Information......................................................... 4
Warranty Information.................................................................. 4
Regulatory Certifications............................................................. 4
Specifications.............................................................................. 5
Refrigerant Charges.................................................................... 6
Installation .................................................................................. 6
Operation
18600PTBM & PTL Series....................................................... 7
18600BUCM & BSTM Series................................................... 7
18600PDL Series..................................................................... 8
CTP-NB Series......................................................................... 8
Pressure Control Settings........................................................... 9
Temperature Control Settings..................................................... 9
Care And Cleaning................................................................10-11
Wiring Diagram
18600PTBM & PTL Series.....................................................12
18600BUCM & BSTM Series.................................................13
18600PDL..............................................................................13
CTP-NB Series.......................................................................14
Replacement Parts...............................................................15-24
Standard Labor Guidelines.......................................................25
Notes....................................................................................26-27
Receiving And Inspecting The Equipment
Even though most equipment is shipped crated, care should be
taken during unloading so the equipment is not damaged while
being moved into the building.
1. Visually inspect the exterior of the package and skid or
container. Any damage should be noted and reported to
the delivering carrier immediately.
2. If damaged, open and inspect the contents with the
carrier.
3. In the event that the exterior is not damaged, yet upon
opening, there is concealed damage to the equipment
notify the carrier. Notification should be made verbally as
well as in written form.
4. Request an inspection by the shipping company of the
damaged equipment. This should be done within 10 days
from receipt of the equipment.
5. Check the lower portion of the unit to be sure legs or
casters are not bent.
6. Also open the compressor compartment housing and
visually inspect the refrigeration package. Be sure lines
are secure and base is still intact.
7. Freight carriers can supply the necessary damage forms
upon request.
8. Retain all crating material until an inspection has been
made or waived.
Uncrating the Equipment
First cut and remove the banding from around the crate.
Remove the front of the crate material, use of some tools will
be required. If the unit is on legs remove the top of the crate
and lift the unit off the skid. If the unit is on casters it can be
"rolled" off the skid.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
3
18600 and CTP-NB Series Service and Installation Manual
Serial Number Information
The serial number on 18600 Series units is located on the
electrical specifications tag affixed inside the compressor
section next to the pressure control.
The serial number on CTP-NB Series units is located on the
front of the unit.
Always have the serial number of your unit available when
calling for parts or service.
Warranty may be deemed invalid if other than
authorized OEM (original equipment manufacture)
replacement parts are used in Delfield equipment.
©2013 The Delfield Company. All rights reserved. Reproduction without
written permission is prohibited. “Delfield” is a registered trademark of The
Delfield Company.
Warranty Information
Visit http://www.delfield.com/minisite/service/warranty_info to:
• Register your product for warranty.
• Verify warranty information.
• View and download a copy of your warranty.
Regulatory Certifications
Models are certified by:
National Sanitation Foundation (NSF)
Underwriters Laboratories (UL)
Underwriters Laboratories of Canada (ULC)
4
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
18600 and CTP-NB Series Service and Installation Manual
Specifications
18600PTBM Pizza tables with raised rail
Model
1/3 Pan Size
Capacity
# Of Doors
# Of
Shelf Max Shelf Area
Shelves Load (LBS)
FT2
Volume
FT3
BTU Load
Base/Rail
BTU Sys. Cap.
Base/Rail
H.P.
Voltz/Hertz/
Phase
Amps
NEMA
Plug
Ship Weight
LBS/KG
18648PTBM
6
(1) 27”
1
124
3.95
10.23
470/441
2001/952
1/4
115/60/1
10.0
5-15P
520/236
18660PTBM
7
19” & 27”
2
70/124
6.51
15.12
694/617
2409/1208
1/3
115/60/1
12.0
5-15P
575/260
2
18672PTBM
9
(2) 27”
18691PTBM
11
(2)27” & (1) 19” 3
124
7.9
18.10
776/794
2967/1587
1/2
115/60/1
14.0
5-20P
635/288
124/70
10.29
24.48
1062/1058
3537/1865
1/2
115/60/1
14.0
5-20P
770/350
18699PTBM
12
(3) 27”
3
124
11.85
27.46
1144/1147
3537/1945
1/2
115/60/1
14.0
5-20P
805/365
186114PTBM
14
(3) 32”
3
140
14.46
33.05
1297/1323
5169/2433
3/4
115/60/1
16.0
5-20P
927/420
18600BUCM Work tables
Model
# Of Doors
# Of
Shelf Max Shelf Area
Shelves Load (LBS)
FT2
Volume
FT3
BTU Load
Base/Rail
BTU Sys. Cap.
Base/Rail
H.P.
Voltz/Hertz/
Phase
Amps
NEMA
Plug
Ship Weight
LBS/KG
18648BUCM
(1) 27”
1
124
3.95
10.23
475/NA
1462/NA
1/5
115/60/1
8.0
5-15P
390/177
18660BUCM
19” & 27”
2
70/124
6.51
15.12
686/NA
1462/NA
1/5
115/60/1
8.0
5-15P
435/197
18672BUCM
(2) 27”
2
18691BUCM
(2)27” & (1) 19” 3
124
7.90
18.10
856/NA
2263/NA
1/4
115/60/1
10.0
5-15P
495/225
124/70
10.29
24.48
1169/NA
2263/NA
1/4
115/60/1
10.0
5-15P
535/243
18699BUCM
(3) 27”
3
124
11.85
27.46
1220/NA
2263/NA
1/4
115/60/1
10.0
5-15P
594/269
186114BUCM
(3) 32”
3
106
14.46
37.24
1373/NA
2813/NA
1/3
115/60/1
12.0
5-15P
685/310
18600BSTM Work table with backsplash
Model
# Of Doors
# Of
Shelf Max Shelf Area
Shelves Load (LBS)
FT2
Volume
FT3
BTU Load
Base/Rail
BTU Sys. Cap.
Base/Rail
H.P.
Voltz/Hertz/
Phase
Amps
NEMA
Plug
Ship Weight
LBS/KG
18648BSTM
(1) 27”
1
124
3.95
10.23
475/NA
1462/NA
1/5
115/60/1
8.0
5-15P
390/177
18660BSTM
19” & 27”
2
70/124
6.51
15.12
686/NA
1462/NA
1/5
115/60/1
8.0
5-15P
435/197
18672BSTM
(2) 27”
2
18691BSTM
(2)27” & (1) 19” 3
124
7.90
18.10
856/NA
2261/NA
1/4
115/60/1
10.0
5-15P
495/225
124/70
10.29
24.48
1169/NA
2261/NA
1/4
115/60/1
10.0
5-15P
535/243
18699BSTM
(3) 27”
3
124
11.85
27.46
1220/NA
2591/NA
1/3
115/60/1
12.0
5-15P
594/269
186114BSTM
(3) 32”
3
106
14.46
37.24
1373/NA
2591/NA
1/3
115/60/1
12.0
5-15P
685/310
18600PTL Pizza table with LiquiTec® rail
Model
1/3 Pan Size
Capacity
# Of Doors
# Of
Shelf Max Shelf Area
Shelves Load (LBS)
FT2
Volume
FT3
BTU Load
Base/Rail
BTU Sys. Cap.
Base/Rail
H.P.
Voltz/Hertz/
Phase
Amps
NEMA
Plug
Ship Weight
LBS/KG
18648PTL
6
(1) 27”
1
124
3.95
10.23
470/441
2001/952
1/4
115/60/1
10.0
5-15P
520/236
18672PTL
9
(2) 27”
2
124
7.90
18.10
776/794
2967/1587
1/2
115/60/1
14.0
5-20P
635/288
18699PTL
12
(3) 27”
3
124
11.85
27.46
1144/1147
3537/1945
1/2
115/60/1
14.0
5-20P
805/365
18600PDL Pizza table with Dual LiquiTec® rails
Model
1/3 Pan Size
Capacity
# Of Doors
# Of
Shelf Max Shelf Area
Shelves Load (LBS)
FT2
Volume
FT3
BTU Load
Base/Rail
BTU Sys. Cap.
Base/Rail
H.P.
Voltz/Hertz/
Phase
Amps
NEMA
Plug
Ship Weight
LBS/KG
18648PDL
6
(1) 27”
1
124
3.95
10.23
424/1058
2001/1865
1/5,
1/3
115/60/1
10.1
5-20P
691/313
18672PDL
9
(2) 27”
2
124
7.90
18.10
703/1588
2001/3174
1/5,
1/2
115/60/1
12.7
5-20P
873/396
CTP-NB Counter top containment rail
Model
1/3 Pan Size
Capacity
# Of Adapter Bars
BTU Load
BTU System
Capacity
H.P.
Voltz/Hertz/
Phase
Amps
NEMA
Plug
Ship Weight
LBS/KG
CTP8146-NB
4
5
305
523
1/5
115/60/1
4.0
5-15P
121/54.9
CTP8160-NB
6
7
462
653
1/5
115/60/1
4.0
5-15P
158/71.7
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
5
18600 and CTP-NB Series Service and Installation Manual
Refrigerant Charges
Refrigerant Charges For 18600 Series Units:
18648-PTBM & PTL . . . . . . . . . . 16 oz. (454g)
18660-PTBM . . . . . . . . . . . . . . . 24 oz. (680g)
18672-PTBM & PTL . . . . . . . . . . 32 oz. (907g)
18691-PTBM . . . . . . . . . . . . . . . 32 oz. (907g)
18699-PTBM & PTL . . . . . . . . . . 32 oz. (907g)
186114-PTBM . . . . . . . . . . . . . 48 oz. (1361g)
18648-BUCM & BSTM . . . . . . . . 16 oz. (454g)
18660-BUCM & BSTM . . . . . . . . 16 oz. (454g)
18672-BUCM & BSTM . . . . . . . . 16 oz. (454g)
18691-BUCM & BSTM . . . . . . . . 16 oz. (454g)
18699-BUCM & BSTM . . . . . . . . 24 oz. (680g)
186114-BUCM & BSTM . . . . . . . 24 oz. (680g)
18648PDL . . . . . . . . . . . . . . . . 40 oz. (1134g)
18672PDL . . . . . . . . . . . . . . . . 56 oz. (1588g)
Refrigerant Charges For CTP-NB Series Units:
CTP8146-NB . . . . . . . . . . . . . . . . 8 oz. (227g)
CTP8160-NB . . . . . . . . . . . . . . . . 8 oz. (227g)
CTP8175-NB . . . . . . . . . . . . . . . 16 oz. (454g)
Installation
Location
These units are intended for indoor use only. Be sure the location
chosen has a floor strong enough to support the total weight of the
cabinet and contents. A fully loaded 72” long model may weigh as
much as 1200 pounds. Reinforce the floor as necessary to provide
for maximum loading.
Plumbing
Self-contained models are standard with a condensate evaporator. If,
for some reason, a unit does not have a condensate evaporator, or the
evaporator fails, the unit’s drain must have an outlet to an appropriate
drainage area or container.
For the most efficient refrigeration, be sure to provide good air
circulation inside and out.
CAUTION
Inside cabinet: Do not pack refrigerator so full that air cannot
circulate.
Outside cabinet: Be sure that the unit has access to ample air. Avoid
hot corners and locations near stoves and ovens.
It is recommended that the unit be installed no closer than 1” from
any wall. PDL models also require 14” (36cm) clearance at the top
and 6” (15cm) clearance at the bottom (casters).
Leveling
A level cabinet looks better and will perform better because the drain
pan will drain properly, the doors will line up with the frames properly,
and the cabinet will not be subject to undue strain.
Some models have casters for your convenience, for ease of cleaning
underneath and for mobility. It is important that the unit be installed
in a stable condition with the front casters locked before operating.
6
Moisture collecting from improper drainage can create
a slippery surface on the floor and a hazard to
employees. It is the owner’s responsibility to provide
a container or outlet for drainage.
Electrical connection
Refer to the amperage data, the serial tag, your local code or the
National Electrical Code to be sure the unit is connected to the proper
power source. A protected circuit of the correct voltage and amperage
must be run for con­nec­tion of the line cord, or permanent connection
to the unit.
The power switch must be turned to OFF and the
unit disconnected from the power source whenever
performing service or maintenance functions.
Never operate the unit without the louvered panel in
place!
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
18600 and CTP-NB Series Service and Installation Manual
Operation: 18600PTBM & PTL Series
Product should be loaded into the unit with care.
Failure to heed these recommendations could result in
damage to the interior of the cabinet or the blower coil.
This unit is equipped with two on/off switches located behind the
louvered machine compartment panel. The unit’s com­pres­sor and all
evaporator fans will begin op­er­at­ing when the main power switch is
turned to the ON position. Tem­per­a­ture ranges for the base are 36°F
to 40°F.
The switch labeled rail is for the raised rail. The rail switch is
accessible through a 1.5” diameter hole in the louvered panel.
Turning this switch to the ON position will activate the refrigeration
for the rail. Temperature ranges for the raised rail are 33°F to 41°F.
Product located in the rail must be removed at the end
of day. This allows you to turn the rail off at night to
save energy and the rail will have time to defrost as
needed.
All R404A models have a high pressure limiting device. Under
severe overloading conditions, or in the event of a condenser fan
failure or a plugged or blocked condenser, this device may shut
down the refrigeration system. This device will automatically reset,
but determining the cause of the high pressure condition should be
investigated by a qualified refrigeration technician.
Refrigerator Evaporator Fan Operation
When the refrigerator is initially powered up or immediately following
a power outage the unit will begin cooling after a 3-6 minute delay.
During normal operation the evaporator fan pulses independently of
the compressor as dictated by the controller as follows:
1.
During the cooling mode, compressor and evaporator fan run
simultaneously.
2.
During the compressor off mode, evaporator fan pulses three
minutes on and three minutes off.
3.
During an actual defrost event other than the off-cycle defrost,
compressor stays off but the evaporator fan runs continuously.
A minimum of one hour of off time per day with the pans removed
from the rail is required to properly defrost the rail.
The power must be turned to OFF and the unit
disconnected from the power source whenever
performing service or maintenance functions.
Never operate the unit without the louvered panel in
place!
Cooling Cycle
Compressor On
Evap Fan
On
Evap Fan
Off
Defrost Cycle
Compressor Off
Evap Fan
On
Evap Fan
Off
Cycles On 3-Min, Off
3-Min
X
Compressor Off
Evap Fan
On
Evap Fan
Off
X
Operation: 18600BUCM & BSTM Series
After turning the ON/OFF switch to ON, the units compressor will
begin operating. Delfield refrigerated bases are designed to maintain
an operational temperature of 36°F to 40°F.
Product should be loaded into the unit with care.
Failure to heed these recommendations could result in
damage to the interior of the cabinet or the blower coil.
Overloading the storage area, restricting the air flow
and continuous opening and closing of the doors and
drawers will hamper the units ability to maintain
operational temperature.
Refrigerator Evaporator Fan Operation
When the refrigerator is initially powered up or immediately following
a power outage the unit will begin cooling after a 3-6 minute delay.
During normal operation the evaporator fan pulses independently of
the compressor as dictated by the controller as follows:
1.
During the cooling mode, compressor and evaporator fan run
simultaneously.
2.
During the compressor off mode, evaporator fan pulses three
minutes on and three minutes off.
3.
During an actual defrost event other than the off-cycle defrost,
compressor stays off but the evaporator fan runs continuously.
Cooling Cycle
Compressor On
Evap Fan
On
X
Evap Fan
Off
Defrost Cycle
Compressor Off
Evap Fan
On
Evap Fan
Off
Cycles On 3-Min, Off
3-Min
Compressor Off
Evap Fan
On
Evap Fan
Off
X
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
7
18600 and CTP-NB Series Service and Installation Manual
Operation: 18600PDL Series
Product should be loaded into the unit with care.
Failure to heed these recommendations could result in
damage to the interior of the cabinet or the blower coil.
This unit is equipped with two on/off switches located behind the
louvered machine compartment panel. The unit’s com­pres­sor and all
evaporator fans will begin op­er­at­ing when the main power switch is
turned to the ON position. Tem­per­a­ture ranges for the base are 36°F
to 40°F (2°C to 4°C).
The switch labeled rail is for the raised rails. The rail switch is
accessible through a 1.5” (3.8cm) diameter hole in the louvered
panel. Turning this switch to the ON position will activate the
refrigeration for the rails. Temperature ranges for the raised rails are
33°F to 41°F (0.5°C to 5°C).
Product located in the rails must be removed at the end
of day. This allows you to turn the rails off at night to save
energy and the rails will have time to defrost as needed.
A minimum of one hour of off time per day with the pans
removed from the rails is required to properly defrost the
rails.
The power must be turned to OFF and the unit
disconnected from the power source whenever
performing service or maintenance functions.
Never operate the unit without the louvered panel in
place!
All R404A models have a high pressure limiting device. Under
severe overloading conditions, or in the event of a condenser fan
failure or a plugged or blocked condenser, this device may shut
down the refrigeration system. This device will automatically reset,
but determining the cause of the high pressure condition should be
investigated by a qualified refrigeration technician.
Refrigerator Evaporator Fan Operation
When the refrigerator is initially powered up or immediately following
a power outage the unit will begin cooling after a 3-6 minute delay.
During normal operation the evaporator fan pulses independently of
the compressor as dictated by the controller as follows:
1.
During the cooling mode, compressor and evaporator fan run
simultaneously.
2.
During the compressor off mode, evaporator fan pulses three
minutes on and three minutes off.
3.
During an actual defrost event other than the off-cycle defrost,
compressor stays off but the evaporator fan runs continuously.
Cooling Cycle
Compressor On
Evap Fan
On
Evap Fan
Off
Defrost Cycle
Compressor Off
Evap Fan
On
Evap Fan
Off
Cycles On 3-Min, Off
3-Min
X
Compressor Off
Evap Fan
On
Evap Fan
Off
X
Operation: ctp-nb Series
The unit is equipped with one on/off switch located on the right
end of the unit. The unit’s com­pres­sor will begin op­er­at­ing when
this switch is turned to the ON position. Tem­per­at­ure ranges for the
rail are 33°F to 41°F.
Product located in the rail must be removed at the
end of day. This allows you to turn the rail OFF at
night to save energy and the rail will have time to
defrost as needed.
8
A minimum of one hour of off time per day with the pans removed
from the rail is required to properly defrost the rail.
The power switch must be turned to OFF and the
unit disconnected from the power source whenever
performing service or maintenance functions.
Never operate the unit without the louvered panel in
place!
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
18600 and CTP-NB Series Service and Installation Manual
Pressure Control Settings
The factory recommended low-pressure control settings
for 18600PTBM’s are: 55psi cut-in and 30psi cut-out
to maintain proper temperature for product in the rail.
The interior temperature is controlled by the thermostat
mounted in the mechanical compartment.
The factory recommended low-pressure control settings
for 18600PTL’s are: 20psi (1.38bar) cut-in and 10psi
(0.70bar) cut-out. The base and rail temperatures are
controlled by the thermostats mounted in the machine
compartment.
A pressure control is located in the machine compartment.
An adjustable control has the word COLDER on the knob,
with an arrow to indicate the adjustment direction. These
controls are field adjustable and do not require a service
agent.
In attempting to adjust the pressure control,
you can do damage to your unit by accidentally
adjusting the differential. Please make small
incremental adjustments if a temperature
adjustment is necessary. It may take an hour
or longer to realize the temperature change
depending on the application and location of the
unit.
Please contact the service department at Delfield
(800) 733-8829 or your local service agent.
Delfield is not responsible for charges incurred
while having the pressure control adjusted.
Temperature Control Settings
A thermostat controls temperature in the 18600PTBM base,
18600PTL base, 18600PTL rail, BUCM, BSTM, 18600PDL
base and 18600PDL rail.
Thermostats are located in the machine compartment. They
are field adjustable and do not require a service agent. The
factory setting is 2.5. Set toward 1 for higher temperatures
and toward 7 for lower temperatures.
Please make small incremental adjustments if
a temperature adjustment is necessary. It may
take an hour or longer to realize the temperature
change depending on the application and location
of the unit.
Contact the service department at Delfield +1
(989) 773-7981 or your local service agent
for additional assistance. Delfield is not
responsible for charges incurred while adjusting
the thermostat.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
9
18600 and CTP-NB Series Service and Installation Manual
Care & Cleaning
Door Gasket Maintenance
Door gaskets require regular cleaning to prevent mold and mildew
build up and also to retain the elasticity of the gasket. Gasket cleaning
can be done with the use of warm soapy water. Avoid full strength
cleaning products on gaskets as this can cause them to become
brittle and crack. Never use sharp tools or knives to scrape or clean
the gasket. Gaskets can be easily replaced and do not require the use
of tools or an authorized service person. The gaskets are “Dart” style
and can be pulled out of the groove in the door and new gaskets can
be “pressed” back into place.
Drain Maintenance - Base
Each unit has a drain located inside the unit that removes the
condensation from the evaporator coil and routes it to an external
condensate evaporator pan. Each drain can become loose or
disconnected during normal use. If you notice water accumulation
on the inside of the unit be sure the drain tube is connected to the
evaporator drain pan. If water is collecting underneath the unit make
sure the end of the drain tube is in the condensate evaporator in the
machine compartment. The leveling of the unit is important as the
units are designed to drain properly when level. Be sure all drain lines
are free of obstructions.
Drawer Maintenance
Drawer Assembly Cleaning
The drawer assembly is designed to be cleaned easily. Both drawer
and tracks are removable without tools. The drawer tracks are
dishwasher safe or can be cleaned in a sink with detergents and a
soft bristle brush. Drawers and tracks should be cleaned on a weekly
basis.
Remove Drawers
Pull the drawer box out until it stops. Lift up on the drawer front and
pull the drawer box completely out. Using a soft bristle brush, clean
the track on the bottom of the drawer box. When finished, it should
be wiped clean of all food and debris.
Tracks
The drawer box assembly must be removed. Pull the drawer tracks
out until they hit a stop. Locate blue safety clips towards the back
of each drawer track. Blue safety clips have a tab on the top. Push
the tab back until it clicks.
Lift up and pull the drawer
tracks all the way out of the
drawer cage. The drawer
tracks are dishwasher safe
tab on top of
or can be cleaned in a sink
blue safety clip with detergents and a soft
bristle brush. Drawers and
tracks should be cleaned on a weekly basis. Using a soft bristle brush,
wash the track making sure each roller is thoroughly cleaned. The
drawer cage should be cleaned with a soft bristle brush, removing
any food and debris gathered on the bottom ledge. Once it’s cleaned
thoroughly with a soft bristle brush, wipe remaining debris clean with
a soft towel.
Reassembly
Push the drawer tracks into the drawer cage. The blue safety clip
must remain pushed towards the back. Lift up and slide the drawer
track all the way into the drawer cage. The blue safety clip will lock
10
in place automatically. Once all tracks are replaced, insert the drawer
box. Rest the drawer box bottom track on the front track roller. Then
push the drawer back in place SLOWLY. When the drawer box is about
half way in you will hit a STOP. You must lift the front of the drawer up
approximately ½” (1.3cm) to continue inward. Clean tracks as often
as possible. The cleaner the tracks are the better they will operate.
Caster Maintenance
Wipe casters with a damp cloth monthly to prevent corrosion.
The power switch must be turned to OFF and the
unit disconnected from the power source whenever
performing service, maintenance functions or cleaning
the refrigerated area.
Refrigerators and Freezers
The interior and exterior can be cleaned using soap and warm water.
If this isn’t sufficient, try ammonia and water or a nonabrasive liquid
cleaner. When cleaning the exterior, always rub with the “grain” of
the stainless steel to avoid marring the finish. Do not use an abrasive
cleaner because it will scratch the stainless steel and can damage the
breaker strips and gaskets.
Stainless Steel Care and Cleaning
To prevent discoloration of rust on stainless steel several important
steps need to be taken. First, we need to understand the properties
of stainless steel. Stainless steel contains 70- 80% iron, which will
rust. It also contains 12-30% chromium, which forms an invisible
passive film over the steels surface, which acts as a shield against
corrosion. As long as the protective layer is intact, the metal is still
stainless. If the film is broken or contaminated, outside elements
can begin to breakdown the steel and begin to form discoloration of
rust. Proper cleaning of stainless steel requires soft cloths or plastic
scouring pads.
NEVER USE STEEL PADS, WIRE BRUSHES OR SCRAPERS!
Cleaning solutions need to be alkaline based or non-chloride cleaners.
Any cleaner containing chlorides will damage the protective film of
the stainless steel. Chlorides are also commonly found in hard water,
salts, and household and industrial cleaners. If cleaners containing
chlorides are used be sure to rinse repeatedly and dry thoroughly.
Routine cleaning of stainless steel can be done with soap and water.
Extreme stains or grease should be cleaned with a non-abrasive
cleaner and plastic scrub pad. Always rub with the grain of the
steel. There are stainless steel cleaners available which can restore
and preserve the finish of the steels protective layer. Early signs of
stainless steel breakdown are small pits and cracks. If this has begun,
clean thoroughly and start to apply stainless steel cleaners in attempt
to restore the passivity of the steel.
Never use an acid based cleaning solution! Many food
products have an acidic content, which can deteriorate
the finish. Be sure to clean the stainless steel surfaces
of ALL food products. Common items include, tomatoes,
peppers and other vegetables.
Cleaning the Condenser Coil
In order to maintain proper refrigeration performance, the
condenser fins must be cleaned of dust, dirt and grease regularly.
It is recommended that this be done at least every three months.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
18600 and CTP-NB Series Service and Installation Manual
Care & Cleaning, continued
If conditions are such that the condenser is totally blocked in three
months, the frequency of cleaning should be increased. Clean the
condenser with a vacuum cleaner or stiff brush. If extremely dirty, a
commercially available condenser cleaner may be required.
Continuous opening and closing of the doors will hamper the unit’s
ability to maintain optimum refrigeration temperature. Top section is
not intended for overnight storage. Product should be removed from
pans. Pans can remain in unit while empty.
Failure to maintain a clean condenser coil can initially cause high
temperatures and excessive run times. Continuous operation with
a dirty or clogged condenser coil can result in compressor failure.
Neglecting the condenser coil cleaning procedures will void any
warranties associated with the compressor and cost to replace the
compressor.
Never use a high-pressure water wash for this
cleaning procedure as water can damage the electrical
components located near or at the condenser coil.
Doors/Hinges
Over time and with heavy use doors the hinges may become loose. If
this happens tighten the screws that mount the hinge brackets to the
frame of the unit. Loose or sagging doors can cause the hinges to pull
out of the frame, which may damage both the doors and the hinges. In
some cases this may require qualified service agents or maintenance
personnel to perform repairs.
Do not place hot pans on/against the blue ABS liner.
Do not throw items into the storage area. Failure to
follow these recommendations could result in damage
to the interior of the cabinet or to the blower coil.
Overloading the storage area, restricting the airflow,
and continuous opening and closing of the doors and
drawers will hamper the units ability to maintain
operational temperature.
Refrigerated rail units
Product in the rail should be removed to the refrigerated base at the
end of the day. This allows you to turn the rail off at night to save
energy and to defrost the rail. It also helps maintain product quality.
The standard wrapped refrigerated rail units are controlled by a lowpressure control that is set to maintain the proper rail temperature.
An on/off switch is also provided for the rail and is required to be shut
off at night. With a LiquiTec rail a thermostat is provided to maintain
rail temperature as well as the rail on/off switch. The LiquiTec rail
is required to be shut off at night as well to allow for defrosting. To
ensure product quality in the rail it is recommended that product be
rotated every four hours.
If adding any item to the unit, be sure to keep in mind
the location of the refrigeration lines on wrapped rail
units. A refrigeration leak in a rail is extremely difficult
and costly to repair. In some cases it cannot be repaired
at all.
Preventing blower coil corrosion
To help prevent corrosion of the blower coil, store all acidic items,
such as pickles and tomatoes, in sealable containers. Immediately
wipe up all spills.
Units with pans should be operated with pans in place.
Operating the unit without all pans in place will lower
efficiency and may damage the unit.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
11
18600 and CTP-NB Series Service and Installation Manual
Wiring Diagram - 18600PTBM Series
Wiring Diagram - 18600PTL Series
12
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
18600 and CTP-NB Series Service and Installation Manual
Wiring Diagram - 18600bucM & bstM Series
Wiring Diagram - 18600PDL Series
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
13
18600 and CTP-NB Series Service and Installation Manual
Wiring Diagram - ctp-nb series
N
L1
POWER SWITCH
CONDENSING UNIT
TEMPERATURE CONTROLS THE CONDENSING UNIT
14
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
G
18600 and CTP-NB Series Service and Installation Manual
18600PTBM Replacement Parts
All 18600PTBM Models
3234290
1" Shelf Support
9321132
1.5" Shelf Support Screw
3234198
Caster, 5, Plate ,Swivel
3234199
Caster, 5, Plate, Swivel, Break
3234392
Hinge, Pan Cover, Center
3234282
Hinge, Pan Cover, End, LH
3234266
Hinge, Pan Cover, End, RH
2190154
Switch, Rocker, 20A/125V,
*000-BN5-0030
Assembly, 1/4 HP Condensing Unit
*000-BN5-0037
Assembly, 1/3 Condensing Unit
*000-BN5-0035
Assembly, 1/2 HP Condenser, Med
186114PTBM
18699PTBM
18691PTBM
18672PTBM
18660PTBM
18648PTBM
X
X
X
*000-BN5-0036
Assembly, 3/4 HP Condenser, Med
*000-187-007Y
Assembly, Dr, Ref, 19X26, LT, 430
*000-187-007X
Assembly, Dr, Ref, 19X26, RT, 430
*000-187-0082
Assembly, Dr, Ref, 27X26, LT, 430
*000-187-0081
Assembly, Dr, Ref, 27X26, RT,430
*000-187-0084
Assembly, Dr, Ref, 32X26, LT, 430
X
*000-187-0083
Assembly, Dr, Ref, 32X26, RT, 430
X
*000-402-004Q
Assembly, Hinged Cover, 6 Pan, RT
*000-402-004V
Assembly, Hinged Cover, 8 Pan
*000-402-004U
Assembly, Hinged Cover, 8 Pan, RT
*000-402-004X
Assembly, Hinged Cover, 10 Pan, LT
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
*000-402-004Y
Assembly, Hinged Cover, 10 Pan, RT
*000-402-0050
Assembly, Hinged Cover, 12 Pan
*000-402-0051
Assembly, Hinged Cover, 12 Pan, LT
*000-402-0052
Assembly, Hinged Cover, 12 Pan, RT
*000-282-006I
Assembly, Control, Tstat & Pressure Control
*000-282-006D
Assembly, Tstat & Low Pressure Control
*000-282-006C
Assembly, Tstat & Low Pressure Control
*000-248-0030
Coil Assembly, R404A
*000-248-0037
Coil Assembly, R404A, Fan Lt
*359-478-003C
Panel, Louver, 14.0, PTB
*359-478-003E
Panel, Louver, 15.0, PTB
*359-478-003D
Panel, Louver, 18.0, PTB
3977984
Shelf, Wire, 19X32DP
3977983
Shelf, Wire, 32X32 DP
3978014
Shelf, Wire, Coated
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
*Exploded assemblies and part prints are on the following pages.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
15
18600 and CTP-NB Series Service and Installation Manual
18600BUCM Replacement Parts
All 18600BUCM Models
3234290
1" Shelf Support
9321132
1.5" Shelf Support Screw
3234198
Caster, 5, Plate, Swivel
3234199
Caster, 5, Plate, Swivel, Brake
*000-298-003P
Control Assembly
186114BUCM
18699BUCM
18691BUCM
18672BUCM
X
X
X
18660BUCM
18648BUCM
X
X
*000-BN5-0031
Assembly, 1/5 Condensing Unit
*000-BN5-0030
Assembly, 1/4 HP Condensing Unit
*000-BN5-0037
Assembly, 1/3 Condensing Unit
*000-187-007Y
Assembly, Dr, Ref, 19X26, LT, 430
*000-187-007X
Assembly, Dr, Ref, 19X26, RT, 430
*000-187-0082
Assembly, Dr, Ref, 27X26, LT, 430
X
X
X
*000-187-0081
Assembly, Dr, Ref, 27X26, RT, 430
X
X
X
X
*000-187-0084
Assembly, Dr, Ref, 32X26, LT, 430
X
*000-187-0083
Assembly, Dr, Ref, 32X26, RT, 430
X
*000-248-0030
Coil Assembly, R404A
X
X
X
X
X
*000-248-0037
Coil Assembly, R404A, Fan Lt
*359-478-0040
Panel, Louver, 14, Hanging
*359-478-0042
Panel, Louver, 15, Hanging
*359-478-0041
Panel, Louver, 18, Hanging
3977984
Shelf, Wire, 19X32DP
3977983
Shelf, Wire, 32X32DP
3978014
Shelf, Wire, Coated
X
X
X
X
X
X
X
X
X
X
X
X
X
X
*Exploded assemblies and part prints are on the following pages.
16
X
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
X
X
X
X
18600 and CTP-NB Series Service and Installation Manual
18600BSTM & 18600PTL Replacement Parts
All 18600BSTM Models
3234290
1" Shelf Support
9321132
1.5" Shelf Support Screw
3234198
Caster, 5, Plate, Swivel
3234199
Caster, 5, Plate, Swivel, Brake
*000-298-003P
Control Assembly
*000-BN5-0031
Assembly, 1/5 Condensing Unit
*000-BN5-0030
Assembly, 1/4 HP Condensing Unit
*000-BN5-0037
Assembly, 1/3 Condensing Unit
*000-187-007Y
Assembly, Dr, Ref, 19X26, LT, 430
*000-187-007X
Assembly, Dr, Ref, 19X26, RT, 430
*000-187-0082
Assembly, Dr, Ref, 27X26, LT, 430
X
X
X
*000-187-0081
Assembly, Dr, Ref, 27X26, RT, 430
X
X
X
X
*000-187-0084
Assembly, Dr, Ref, 32X26, LT, 430
X
*000-187-0083
Assembly, Dr, Ref, 32X26, RT, 430
X
*000-248-0030
Coil Assembly, R404A
X
X
X
X
X
*000-248-0037
Coil Assembly, R404A, Fan Lt
*359-478-0040
Panel, Louver, 14, Hanging
*359-478-0042
Panel, Louver, 15, Hanging
*359-478-0041
Panel, Louver, 18, Hanging
3977984
Shelf, Wire, 19X32DP
3977983
Shelf, Wire, 32X32DP
3978014
Shelf, Wire, Coated
186114BSTM
18699BSTM
X
18691BSTM
18672BSTM
X
18660BSTM
18648BSTM
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
All 18600PTL Models
3234290
1" Shelf Support
3516053
Coil, Solenoid, 120V
9321132
1.5" Shelf Support Screw
3234392
Hinge, Pan Cover, Center
*000-187-0082
Assembly, Dr, Ref, 27X26, LT, 430
3234282
Hinge, Pan Cover, End, LH
*000-402-0055
Assembly, Hinged Cover, 12 Pan, PTL
3234266
Hinge, Pan Cover, End, RH
263-ASB-0030
Bracket, Cutting Board, Center
3978014
Shelf, Wire, Coated
263-110-0034
Bracket, Cutting Board, LH
2190154
Switch, Rocker, 20A/125V
263-110-0036
Bracket, Cutting Board, RF
3516225
Valve, Expansion, Frz, 1/4Ton
3234198
Caster, 5, Plate, Swivel
3516102
Valve, Solenoid, 1/4ODF
3234199
Caster, 5, Plate, Swivel, Brake
*000-BN5-0030
Assembly, 1/4 HP Condensing Unit
*000-BN5-0035
Assembly, 1/2HP Condenser, MED
*000-282-006L
Assembly, Control, 15A
*000-282-006M
18699PTL
18672PTL
18648PTL
X
X
X
Assembly, Control, 20A
X
X
*000-187-0081
Assembly, Dr, Ref, 27X26, RT, 430
X
X
*000-402-0054
Assembly, Hinged Cover, 6 Pan, PTL
*000-248-0030
Coil Assembly, R404A
*000-248-0037
Coil Assembly, R404A, Fan Lt
X
X
X
X
X
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
17
18600 and CTP-NB Series Service and Installation Manual
CTP8000-NB & 18600PDL Replacement Parts
All CTP8000-NB Models
243-ALS-0032
Divider, Bar, Cold
3234392
Hinge, Pan Cover, Center
3234282
Hinge, Pan Cover, End, LH
3234266
Hinge, Pan Cover, End, RH
9321374
Pin, Hinge, Salad Pan
*000-254-Z000B
Condenser Assembly, 1/5HP, CTP-8100
*000-AUX-0038
Condensing Unit Assembly, 1/5HP, CTP
*223-016-Z000P
Cover, Hinged, CTP
*312-016-003U
Cover, Pan, Rail, 8 Pan
*312-016-003W
Cover, Pan, Rail, 12 Pan
243-ALS-0030
Divider, Bar, Cold
243-ALS-0036
Divider, Bar, Cold
*356-411-Z0009
Louver, Front, CTP-8100
X
*026-411-Z000A
Louver, Rear, CTP-8100
X
*356-411-0004
Panel, Louver, Front CTP-8100
CTP8175-NB
CTP8160-NB
CTP8146-NB
X
X
X
X
X
X
X
X
X
X
X
All 18600PDL Models
*000-187-0082
Assembly, Door, Ref, 27X26, LT, 430
3234266
Hinge, Pan Cover, End, RH
*000-402-0054
Assembly, Hinged Cover, 6 Pan, PTL
9321374
Pin, Hinge, Salad Pan
263-110-0034
Bracket, Cutting Board
3978014
Shelf, Wire, Coated
263-110-0036
Bracket, Cutting Board
3234290
Support, Shelf, Plastic
3234186
Caster, 3DIA, Swivel, Plate
2190154
Switch, Rocker, 20A/125V
3234392
Hinge, Pan Cover
3516135
Thermometer, Hanging, 4
3234282
Hinge, Pan Cover, End, LH
Part Number
Description
18672PDL
*000-BN5-003Y
Assembly, 1/2-1/5 Cond Unit Stacked
X
18648PDL
*000-BN5-0040
Assembly, 1/3-1/5 Cond Unit Stacked
X
*000-282-006V
Assembly, Control, L/T, 48”
X
*000-282-006K
Assembly, Control, L/T, 72”
X
*000-187-0081
Assembly, Door, Ref, 27X26, RT, 430
X
X
*000-248-0030
Coil Assembly, R404A
*000-248-0037
Coil Assembly, R404A, Fan Lt
X
*359-478-003E
Panel, Louver, 15.0, PTB
X
*359-478-003D
Panel, Louver, 18.0, PTB
X
*Exploded assemblies and part prints are on the following pages.
18
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
18600 and CTP-NB Series Service and Installation Manual
Replacement Parts - Control Assemblies
Key
1
2
3
Part Number
000-282-006I
2193942
2190154
2194824
Key
-
Part Number
000-282-006C &
000-282-006D
2193927
2190154
2194824
1
2
3
Description
Thermostat & Dual Pressure Control Assembly
Dual pressure control
Rocker switch, 20A/125V
Control, Danfoss, GDM, 115V
1
2
3
Description
Thermostat & Low Pressure Control Assembly
1
Low pressure control
Rocker switch, 20A/125V
Control, Danfoss, GDM, 115V
2
3
Key
1
2
Part Number
000-298-003P
2194810
2190154
Description
Control Assembly
Control, Danfoss, GDM, 115V
Rocker switch, 20A/125V
1
Key
1
2
3
4
Part Number
000-282-006L &
000-282-006M
2193927
000-282-0051
2190154
2194824
Low pressure control
Tstat Assembly, Danfoss, MK7
Rocker switch, 20A/125V
Control, Danfoss, GDM, 115V
Key
1
2
3
Part Number
000-282-006K
000-282-0051
2190154
2194824
Description
72” LiquiTec Dual Rail Control Assembly
Tstat Assembly, Danfoss, MK7
Rocker switch, 20A/125V
Control, Danfoss, GDM, 115V
Key
1
2
3
Part Number
000-282-006V
000-282-0053
2190154
2194824
Description
48” LiquiTec Dual Rail Control Assembly
Tstat Assembly, Danfoss, MK7
Rocker switch, 20A/125V
Control, Danfoss, GDM, 115V
2
1
Description
Control Assembly, LiquiTec, 2SW
2
1
1
2
3
4
3
2
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
19
18600 and CTP-NB Series Service and Installation Manual
Replacement Parts - Condensing Unit Assemblies
2
3
4
1
5
6
Part Number
Description
000-AUX-0038
Condensing Unit Assembly, 1/5HP, CTP
7
8
3526694
Compressor
3516082
Condenser Coil
-
000-BN5-0031
Assembly, 1/5 Condensing Unit
3516172
Fan Blade
1
2160028
Fan, Axial, 5.5”, 120V
2162691
Fan Motor
2
2160030
Guard, Fan, 6.0”
031-264-0000
Fan Motor Bracket
3
026-C58-0037
Shroud, Condenser Coil
3516191
Filter Drier
4
3526997
Compressor, Danfoss, TF4CLS
Temp Control
5
2194787
Start Capacitor
6
3516322
Filter Dryer
7
075-231-0030
Condensate Pan
8
3516454
Condenser Coil
3516047
6
5
2
4
3
3
2
4
1
1
5
7
6
7
8
9
8
Key
Part Number
Description
-
000-BN5-0035
Assembly, 1/2HP Condenser, Med
-
000-BN5-0030
Assembly, 1/4 HP Condensing Unit
1
3516554
Condenser fan blade
1
2160028
Fan, Axial, 5.5”, 120V
2
2160019
Condenser fan guard
2
2160030
Guard, Fan, 6.0”
3
2162716
Condenser fan motor, 115V
3
026-C58-0037
Shroud, Condenser Coil
4
3516462
Capacitor, start-run assy
4
3526999
Compressor, Danfoss, NF5.5CLX
5
3527026
Compressor, Danfoss, SC12MLX
5
2194787
Start Capacitor
6
3516331
Hi pressure switch
6
3516322
Filter Dryer
7
3516322
Filter Drier
7
075-231-0030
Condensate Pan
8
075-231-0031
Pan, Condensate
8
3516454
Condenser Coil
9
3516455
Condenser coil
20
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
18600 and CTP-NB Series Service and Installation Manual
Replacement Parts - Condensing Unit Assemblies
2
1
3
2
3
4
1
5
4
6
7
5
8
9
Key
Part Number
Description
Key
Part Number
Description
-
000-BN5-0036
Assembly, 3/4 HP Condenser, Med
-
000-BN5-0037
Assembly, 1/3 Condensing Unit
1
2160019
Guard, Fan, Wire
1
2160028
Fan, Axial, 5.5”, 120V
2
3516442
Capacitor, Start, Run, Assembly
2
2160030
Guard, Fan, 6.0”
3
3527021
Compressor, 3/4 HP Med
3
026-C58-0037
Shroud, Condenser Coil
4
3516322
Drier, Filter, (2)Inlet
4
3527000
Compressor, Danfoss, NF7CLS
5
3516456
Coil, Condenser, 3/4 HP
5
2194788
Start Capacitor
-
3516433
Blade, Fan, 25Deg, 10", CW
6
3516322
Filter Drier
-
2162716
Motor, Fan, 16W, 115V, CW
7
3516458
Receiver tank
-
075-231-0031
Pan, Condensate, Sm
8
075-231-0030
Pan, Condensate
9
3516454
Condenser Coil
5
4
2
3
1
6
Key
Part Number
Description
-
000-254-Z000B
Condenser Assembly, 1/5HP, CTP-8100
1
3516082
Condenser Coil
2
3516172
Fan Blade
3
2162691
Fan Motor
4
3516047
Temp Control
5
3526694
Compressor
6
031-264-0000
Fan Motor Bracket
-
3516191
Filter Drier
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
21
18600 and CTP-NB Series Service and Installation Manual
Replacement Parts - Condensing Unit Assemblies
000-BN5-003Y
Assembly, 1/2-1/5 Stacked
3516433
Blade, Fan, 25Deg, 10", CW
3516457
Blade, Fan, 7.25 DIA.
2194789
Capacitor, Start, 240MFD
2194787
Capacitor, Start, 280MFD
3516455
Coil, Cond., 1/2 HP
3516454
Coil, Cond., 1/5, 1/4
3526997
Comp, 1/5HP, 115/60, R404A
3527001
Comp, SC12CLX.2, 115/60HZ
3516446
Compressor, Relay, Danfoss
3516322
Drier, Filter, (2) Inlet
2160020
Guard, Fan, 7.25
2160019
Guard, Fan, Wire
2162513
Motor, Fan, 35W, Blast
2162717
Motor, Fan, 9W, 115V, CW
3516193
Regulator, Pressure, 1/2
3516441
Relay, Compressor, SC12CLX.2
3516225
Valve, Exp, Frz, 1/4 Ton
000-BN5-0040
Assembly, 1/3-1/5 Stacked
3516457
Blade, Fan, 7.25 DIA.
2194787
Capacitor, Start, 280MFD
2194788
Capacitor, Start, 320MFD
3516454
Coil, Cond., 1/5, 1/4
3526997
Comp, 1/5HP, 115/60, R404A
3527000
Comp, NF7CLS, 115V/60HZ
3516446
Comp, Relay, Danfoss
3516322
Drier, Filter, (2) Inlet
2160020
Guard, Fan, 7.25
2162717
Motor, Fan, 9W, 115V, CW
3516193
Regulator, Pressure, 1/2
3516438
Relay, Comp, Ovld, NF7CLX
3516225
Valve, Exp, Frz, 1/4 Ton
22
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
18600 and CTP-NB Series Service and Installation Manual
Replacement Parts - Evaporator Coil Assembly
1
1
4
2
4
2
3
3
5
6
6
5
7
9
8
8
7
Key
1
2
3
4
5
6
7
8
-
Part Number
000-248-0030
2160024
2160023
3516095
030-232-0003
3516273
030-233-0001
075-231-0033
030-234-0003
2184317
2194808
2194809
Description
Coil Assembly, R404A, Ref
Guard, fan, 4.7"
Fan, axiel, 120V
Coil, evaporator
Back, evaporator, enclosure
Expansion valve, 1/4, R-404a
Side, coil, angled
Drip pan, evaporator
Front, coil
Harness, coil
Probe, Defrost, Danfoss, Control
Probe, Temp, Sensor, Danfoss
Key
Part Number
Description
1
2
3
4
5
6
7
8
9
-
000-248-0037
2160024
2160023
3516095
030-232-0003
000-BNH-0030
030-233-0038
3516273
030-234-0003
030-233-0039
2184317
2194808
2194809
Coil Assembly, R404A, Ref, Fan Lt
Guard, fan, 4.7"
Fan, axiel, 120V
Coil, evaporator
Back, evaporator, enclosure
Drip pan, evaporator
Side, coil, angled, Rt, Blank
Expansion valve, 1/4, R-404a
Front, coil
Side, Coil, Angled, Lt, 2Fan
Harness, coil
Probe, Defrost, Danfoss, Control
Probe, Temp, Sensor, Danfoss
Replacement Parts - Louvered Panels
Description
Part Number
Description
Part Number
Description
356-411-Z0009
Louver, Front, CTP-8100
359-478-003C
Panel, Louver, 14.0, PTB
359-478-0040
Panel, Louver, 14, Hanging
026-411-Z000A
Louver, Rear, CTP-8100
359-478-003E
Panel, Louver, 15.0, PTB
359-478-0042
Panel, Louver, 15, Hanging
356-411-0004
Panel, Louver, Front CTP-8100
359-478-003D
Panel, Louver, 18.0, PTB
359-478-0041
Panel, Louver, 18, Hanging
Part Number
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
23
18600 and CTP-NB Series Service and Installation Manual
Replacement Parts - Door & Cover Assemblies
2
1
1
2
Key
Part Number
Description
Part Number
Description
-
000-187-007X
Assembly, Dr, Ref, 19X26, RT, 430
000-402-0054
Assembly, Hinged Cover, 6 Pan, PTL
1
1701183
Gasket, Dr, 19, Mark7
000-402-004Q
Assembly, Hinged Cover, 6 Pan, RT
2
0160179
Hinge Kit
000-402-004V
Assembly, Hinged Cover, 8 Pan
-
000-187-007Y
Assembly, Dr, Ref, 19X26, LT, 430
000-402-004U
Assembly, Hinged Cover, 8 Pan, RT
Assembly, Hinged Cover, 10 Pan, LT
1
1701183
Gasket, Dr, 19, Mark7
000-402-004X
2
0160179
Hinge Kit
000-402-004Y
Assembly, Hinged Cover, 10 Pan, RT
-
000-187-0081
Assembly, Dr, Ref, 27X26, RT,430
000-402-0050
Assembly, Hinged Cover, 12 Pan
1
1701185
Gasket, Dr, 27, Mark7
000-402-0051
Assembly, Hinged Cover, 12 Pan, LT
2
0160179
Hinge Kit
000-402-0055
Assembly, Hinged Cover, 12 Pan, PTL
-
000-187-0082
Assembly, Dr, Ref, 27X26, LT, 430
000-402-0052
Assembly, Hinged Cover, 12 Pan, RT
1
1701185
Gasket, Dr, 27, Mark7
223-016-Z000P
Cover, Hinged, CTP
Cover, Pan, Rail, 8 Pan
Cover, Pan, Rail, 12 Pan
2
0160179
Hinge Kit
312-016-003U
-
000-187-0083
Assembly, Dr, Ref, 32X26, RT, 430
312-016-003W
1
1701186
32" Door Gasket
2
0160179
Hinge Kit
-
000-187-0084
Assembly, Dr, Ref, 32X26, LT, 430
1
1701186
32" Door Gasket
2
0160179
Hinge Kit
24
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
18600 and CTP-NB Series Service and Installation Manual
Standard Labor Guidelines To Repair Or Replace Parts On Delfield Equipment
Advice and recommendations given by Delfield Service Technicians do not constitute or guarantee any special coverage.
•A maximum of 1-hour is allowed to diagnose a defective component.
•A maximum of 1-hour is allowed for retrieval of parts not in stock.
•A maximum travel distance of 100 miles round trip and 2-hours will be reimbursed.
•Overtime, installation/start-up, normal control adjustments, general maintenance, glass breakage, freight damage, and/or
correcting and end-user installation error will not be reimbursed under warranty unless pre-approved with a Service Work
Authorization from Delfield. You must submit the number with the service claim.
LABOR OF 1-HOUR IS ALLOWED TO REPLACE:
•Thermostat
•Evaporator/Condenser Fan Motor and Blade
•Door Hinges, Locks, and Gaskets
•Compressor Start Components and Overload Protector
•Thermometer
• Solenoid Coil
LABOR OF 2 HOURS TO REPLACE:
•Drawer Tracks/Cartridges
• Pressure Control
•Solenoid Valve
• Locate/Repair Leak
LABOR OF 3 HOURS TO REPLACE:
•Condenser or Evaporator Coil
•Expansion Valve
LABOR OF 4 HOURS TO REPLACE
•Compressor
This includes recovery of refrigerant and leak check.
$55.00 maximum reimbursement for refrigerant recovery (includes recovery machine, pump, torch, oil, flux, minor fittings,
solder, brazing rod, nitrogen or similar fees.)
REFRIGERANTS
•R404A A maximum of $15.00/lb. or$1.00/oz. will be reimbursed.
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
25
18600 and CTP-NB Series Service and Installation Manual
Notes
26
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
18600 and CTP-NB Series Service and Installation Manual
Notes
For customer service, call (800) 733-8829, (800) 773-8821, Fax (989) 773-3210, www.delfield.com
27
Covington, TN
Mt. Pleasant, MI
Thank you for choosing Delfield!
Help is a phone call away. Help our team of professional, courteous customer
service reps by having your model number and serial number available at the time
of your call (800) 733-8829.
Model:________________________ S/N: _______________________
Installation Date:________________
For a list of Delfield’s authorized parts depots,
visit our website at www.delfield.com
Register your Delfield warranty
online. Go to www.delfield.com
under the service tab to complete.
Delfield
™
®
980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • (989) 773-7981 or (800) 733-8829 • Fax (989) 773-3210 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2013 The Delfield Company. All rights reserved. Printed in the U.S.A.
DM18PTB 05/13
9291455
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement