Trendnet TV-IP312W, TV-IP312 User guide

Trendnet TV-IP312W, TV-IP312 User guide
P REFACE
Thank you for purchasing the TV-IP312/TV-IP312W SecurView
Wire/Wireless Internet Camera Server or Day/Night Internet Camera
Server, a powerful dual-codec wireless network camera with the 2way audio function that provides the high-quality image and on-thespot audio via the Internet connection. The Infrared LEDs and light
sensor enable the camera to capture images even in the dark
environment. The camera can be installed as a standalone system
within your application environment easily and quickly, and supports
remote management function so that you can access and control it
using a Web browser on your computers.
This guide will provide you more information of instruction and
illustrations on how to use your camera, which includes:
Chapter 1
Introduction to Your Camera describes the features of
the camera. You will also know the components and
functions of the camera.
Chapter 2
Hardware Installation helps you install the camera
according to your application environment. You can use
this camera at home, at work, at any where you want.
Chapter 3
Accessing the Camera lets you start using your camera
without problem. The camera can be set up easily and
work within your network environment instantly.
Chapter 4
Configuring the Camera guides you through the
configuration of the camera using the web browser on
your PC.
Chapter 5
Using SecurView™ shows you the detail instructions on
operating SecurView™ software.
-1-
Chapter 6
Appendix provides the specification of the camera and
some useful information for using your camera.
NOTE The illustrations and configuration values in this guide are for
reference only. The actual settings depend on your practical
application of the camera.
-2-
Contents
PREFACE ............................................................................ 1
CHAPTER 1........................................................................ 5
INTRODUCTION .............................................................. 5
1.1
1.2
1.3
1.4
CHECKING THE PACKAGE CONTENTS ........................................... 5
GETTING TO KNOW YOUR CAMERA ............................................. 6
FEATURES AND BENEFITS ......................................................... 10
SYSTEM REQUIREMENT ............................................................ 12
CHAPTER 2...................................................................... 13
HARDWARE INSTALLATION ..................................... 13
2.1
2.2
2.3
INSTALLING THE CAMERA STAND .............................................. 13
CONNECTING THE CAMERA TO LAN/WLAN .............................. 14
APPLICATIONS OF THE CAMERA ................................................ 15
3.1
3.2
3.3
USING IP SETUP ..................................................................... 16
ACCESSING TO THE CAMERA..................................................... 21
CONFIGURING THE IP ADDRESS OF THE PC ................................. 24
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
USING THE WEB CONFIGURATION ............................................. 25
USING SMART WIZARD ............................................................ 26
BASIC SETUP .......................................................................... 31
NETWORK SETTINGS................................................................ 36
SETTING UP VIDEO & AUDIO..................................................... 44
EVENT SERVER CONFIGURATION ............................................... 49
MOTION DETECT .................................................................... 54
EVENT CONFIG ....................................................................... 56
TOOLS .................................................................................. 62
CHAPTER 3...................................................................... 16
ACCESSING THE CAMERA ......................................... 16
CHAPTER 4...................................................................... 25
CONFIGURING THE CAMERA ................................... 25
-3-
4.10 USB ..................................................................................... 64
4.11 INFORMATION ........................................................................ 66
CHAPTER 5...................................................................... 68
SECURVIEW™ SOFTWARE ......................................... 68
5.1 INSTALLATION ................................................................... 68
5.2 USING INSTALLATION ........................................................ 74
ITEM FEATURES ................................................................................ 75
TO ADD A CAMERA ........................................................................... 81
TO REMOVE A CAMERA ..................................................................... 84
TO LINK TO THE WEB PAGE OF THE CAMERA ......................................... 85
TO RECORD VIDEO ........................................................................... 86
TO CONFIGURE THE RECORDING SETTINGS ........................................... 92
TO PLAYBACK THE RECORDED VIDEO ................................................... 93
TO SET UP MOTION DETECTION OPTIONS ............................................. 94
ACCOUNT....................................................................................... 96
OTHER ........................................................................................... 96
INFORMATION ................................................................................. 98
CHAPTER 6...................................................................... 99
APPENDIX ....................................................................... 99
A.1 SPECIFICATION ....................................................................... 99
A.2 GLOSSARY OF TERMS ....................................................... 101
-4-
C HAPTER 1
I NTRODUCTION
1.1 Checking the Package Contents
Please check the packaging contents. The packaging should include
the following:







TV-IP312/TV-IP312W
Multi-Language Quick Installation Guide
CD-ROM (Utility & User’s Guide)
Detachable External Antenna (for TV-IP312W only)
Camera Stand.
RJ-45 Ethernet Cable
AC Power Adapter (5VDC, 2.5A)
NOTE : If there is any item damage or missing, please contact your
local authorized deal for replacement.
-5-
1.2 Getting to Know Your Camera
TV-IP312 (Front/Back View)
-6-
TV-IP312W (Front/Back View)
-7-
-
Internal Microphone: It allows the camera to receive the sound
or voice.
-
Infrared LEDs: It allows your camera to capture clear image in a
dark environment.
-
Light Sensor: It is used to trigger on and off the Infrared LEDs
according the environmental light level.
-
Power LED: A steady orange light indicates the camera is
powered on.
-
Link LED: A flash green light indicates the camera’s network
connection correctly.
-
Detachable Antenna (TV-IP312W only):
The detachable external antenna allows you to adjust its position
to obtain the maximum signal.
-
USB Port: Connects an external USB Flash Drive, Hard Drive. It
provides the power distribution up to 500mA.
-
USB Unmount Button: Removed the connected USB device
safely.
Pressing the Unmount button for four seconds, the Power LED
will start flashing. After the Power LED rsumes the steady orange
light, you can remove the USB device safely.
-
Camera Stand Connection: Connects the camera with the
camera stand.
-8-
-
Speaker Connector: Connects a external active speaker to the
camera.
-
Power Connector: Connects the AC power adapter to supply
power to the camera.
-
LAN Port: It is used to connect the network RJ-45 cable, which
supports the NWay protocol so that the camera can detect the
network speed automatically.
-
Reset Button: Reset will be initiated when the reset button is
pressed once. The power LED begins to flash.
Factory Reset will be initiated when the reset button is pressed
continuously for three seconds or when Power LED begins to
light up. Release the reset button and the Power LED will begin to
flash.
-9-
1.3 Features and Benefits

MPEG4/MJPEG Dual-codec Supported
The camera provides you with excellent images by the
MPEG4/MJPEG dual-codec selectable technology, allowing you to
adjust image size and quality, and bit rate according to the
networking environment.

2-way Audio Capability
The built-in microphone of the camera provides on-the-spot
audio via the Internet, allowing you to monitor the on-site voice.
In addition, you can connect an external speaker to the camera to
speak through the camera; the camera is embedded with an echo
cancellation processor to provide a better sound quality.

Day & Night Surveillance Supported
The six Infrared LEDs around the standard lens assembly enable
the camera to capture crystal clear images in the dark
environment or at night. When the Light Sensor detects the
environmental light level becomes low, the camera captures the
images in black & white mode using these infrared LEDs.

Supports Multiple Profiles
The camera supports multiple profiles simultaneously, so that you
can separately set up different image settings (such as image
quality and frame rate) for the three video types of the camera:
MPEG4, MJPEG, and 3GPP.

Supports RTSP
The camera supports RTSP (Real Time Streaming Protocol), which
is a technology that allows you to view streaming media via the
network. You can view the real-time video with the Quick Time
player or RealPlayer. To view the real-time streaming image on
your computer, open the Web browser and enter the RTSP link:
rtsp://(IP address of the camera)/mpeg4.
- 10 -

Remote Control Supported
By using a standard Web browser or the bundled SecurView™
software application, the administrator can easily change the
configuration of the camera via Intranet or Internet. In addition,
the camera can be upgraded remotely when a new firmware is
available. The users are also allowed to monitor the image and
take snapshots via the network.

Supports Connection to the External Devices
With the auxiliary Input/Output connectors, you can connect the
camera to a variety of external devices, such as the external
speaker and the USB Flash Drive or Hard Drive.

Multiple Platforms Supported
The camera supports multiple network protocols, including
TCP/IP, SMTP Email, HTTP, and other Internet related protocols.
Therefore, you can use the camera in Windows 2000 and
Windows XP, Windows Vista

Multiple Applications Supported
Through the remote access technology, you can use the cameras
to monitor various objects and places for your own purposes.
For example, babies at home, patients in the hospital, offices and
banks, and more. The camera can capture both still images and
video clips, so that you can keep the archives and restore them at
any time.
- 11 -
1.4 System Requirement

Networking
LAN:
10Base-T Ethernet or 100Base-TX Fast Ethernet.
WLAN: IEEE 802.11b/g.

Accessing the Camera using Web Browser
Platform:
Microsoft® Windows® 7/Vista/XP/2000
CPU:
Intel Pentium III 350MHz or above
RAM:
128MB
Resolution: 800x600 or above
Browser:
Microsoft® Internet Explorer 6.0 or above

Accessing the Camera using SecurView™ Software View
Platform:
Microsoft® Windows® 7 (32-bit)/Vista (32-bit)/XP (32bit)/2000
Hardware Requirement:
1 camera connected: Intel Pentium 4 1GHz; 512MB RAM
2 ~ 4 cameras connected: Intel Pentium 4 1.3GHz; 512MB RAM
5 ~ 8 cameras connected: Intel Pentium 4 2.4GHz; 1GB RAM
9 ~ 16 cameras connected: Intel Pentium 4 3.4GHz; 2GB RAM
Resolution: 1024x768 or above
NOTE If you connect multiple cameras to monitor various places
simultaneously, you are recommended to use a higher
performance computer.
- 12 -
C HAPTER 2
H ARDWARE I NSTALLATION
2.1 Installing the Camera Stand
The camera comes with a camera stand, which uses a swivel ball
screw head to lock the camera. When the camera stand is attached,
you can place the camera anywhere by mounting the camera through
the three screw holes located in the base of the camera stand.
The Camera Stand
- 13 -
2.2 Connecting the Camera to LAN/WLAN
Connects an Ethernet cable to the
LAN port located on the Camera’s
real panel, and then attaches it to the
network.
Connects an antenna to the antenna
connector. (TV-IP312W only)
Attach the external power supply to
the DC power input connector
located on Camera’s real Panel, and
then connect it to your local power
supply.
NOTE Please configure the wireless setting via the wire connection.
- 14 -
2.3 Applications of the Camera
The camera can be applied in multiple applications, including:

Monitor local and remote places and objects via Internet or
Intranet.

Capture still images and video clips remotely.

Upload images or send email messages with the still images
attached.
The following diagram explains one of the typical applications for
your camera and provides a basic example for installing the camera.
- 15 -
C HAPTER 3
ACCESSING THE C AMERA
3.1 Using IP Setup
The camera comes with a conveniently utility, IP Setup, which is
included in the Installation CD-ROM, allowing you to search the
camera on your network easily.
1. Insert the Installation CD-ROM into your computer’s CD-ROM
drive to initiate the Auto-Run program.
2. Click the IP Setup from the Auto-Run menu screen. Then IP
Setup Wizard will appear. Click “Next” when the Welcome to the
IPSetup Setup Wizard appears.
- 16 -
3. Click “Browse” to choose the desired destination location. By
default, the destination location is C:\Program
Files\TRENDnet\IPSetup. Then Click “Next”.
4. Click “Next” to confirm the IPSetup software to be installed to the
computer.
- 17 -
5. When the Installation Complete window appears, click “Finish”.
- 18 -
6. After installing the IPSetup utility, the application is automatically
installed to your computer, and creates a folder in “ Start
\Program\TRENDnet\IPSetup”.
7. Click Start > Programs > TRENDnet > IPSetup, and then click
IPSetup
8. The IPSetup window will appear. It will search the Camera within
the same network.
Camera Display Area
- 19 -
-
Camera Display Area: It shows the connected camera(s) within
the same network
Double click the IP address, it will link to Camera’s Web
Configuration page.
-
Change IP: Click this button to bring up the following window. It
allows you to change the IP Address. You can select either Static
IP or click DHCP. Then, enter the Administrator ID & password.
By default ID/password is: admin. When complete, click “Change”.
-
Search: Click this button to search the connected camera in
the same network.”
-
Exit: Click this button to exit the program.
- 20 -
3.2 Accessing to the Camera
1. Open the Web browser on your computer (example showed in
the User’s Guide is based on the Internet Explorer)
2.
Type the default IP address (192.168.10.30) and then press [Enter].
3. When the login window appears, enter the default User name
(admin) and password (admin) and press OK to access to the
main screen of the camera’s Web Configuration.
- 21 -
NOTE If you are initially access to the camera, you will be ask to install
a new plug-in for the camera. Permission request depends on
the Internet security settings of your computer. Click Yes to
proceed.
After you login into the Web Configuration of the camera, the main
page will appear as below:
Camera Information
Zoom In
Live View/ Setup
Night Mode
Compression
Live View Image
Function
The main page of the Web Configuration provides you with many
useful information and functions, including:
- 22 -

Camera Information – Display the camera’s location and the
current date & time. The information can be modified in the Web
Configuration.

Nightmode– Click the button to enable the “nightshot mode” to
deliver clearer images in the dark environment. However, this will
reduce the frame rate of video setting. (TV-IP312/TV-IP312W only)

Live View Image – Displays the real-time image of the connected
camera.

Zoom In – Click the buttons to zoom in the live view image by 1x,
2x, and 3x.

Live View/Setup Switch – Click Setup to configure the camera.
For details, see Chapter 4.

Compression Buttons – Select to transmit and record the video
using MPEG4 or MJPEG compression.

Function – Use these buttons to control the audio and video
functions.
 Manual Record allows you to record and save a video clip.
 Snapshot allows you to capture and save a still image.
 Browse allows assign the destination folder to store the
video clips and still images.
 Talk allows you to speak out through the camera. Please
note only one user is allowed to use this function at the same
time.
 Listen allows you receive the on-site sound and voice from
the camera.
- 23 -
3.3 Configuring the IP Address of the PC
If you are failed to access to the camera, please check the IP address of
your computer. When you connect the camera to your computer
directly to proceed with configuration of the camera, you need to set
up the IP addresses to be in the same segment for the two devices to
communicate.
1. On your computer, click Start > Control Panel to open the
Control Panel window.
2. Double-click Network Connection to open the Network
Connection window.
3. Right-click Local Area Connection and then click Properties
from the shortcut menu.
4. When the Local Area Connection Properties window appears,
select the General tab.
5. Select Internet Protocol [TCP/IP] and then click Properties to
bring up the Internet Protocol [TCP/IP] Properties window.
6. To configure a fixed IP address that is within the segment of the
camera, select the Use the following IP address option. Then,
enter an IP address into the empty field. The suggested IP address
is 192.168.10.x (x is 0~254 except 30), and the suggested Subnet
mask is 255.255.255.0.
7. When you are finished, click OK.
- 24 -
C HAPTER 4
CONFIGURING THE C AMERA
4.1 Using the Web Configuration
You can access and manage the camera through the Web browser or
from the SecurView™ software (see chapter 5 in more detail). This
chapter describes the Web Configuration, and guides you through the
configuration of the camera by using the web browser.
To configure the camera, click Setup on the main page of Web
Configuration. The Web Configuration will start from the Basic page.
- 25 -
The Web Configuration contains the settings that are required for the
camera in the left menu bar, including Smart Wizard, Basic, Network,
Video/Audio, Event Server, Motion detect, Event Config, Tools,
USB, and Information.
4.2 Using Smart Wizard
The camera’s Smart Wizard lets you configure your camera easily and
quickly. The wizard will guide you through the necessary settings with
detailed instructions on each step.
To start the wizard, click Smart Wizard in the left menu bar.
- 26 -
Step 1. Camera Settings
Enter Camera
name, Location,
New Admin
password and
enter again to
confirm Admin
password
Step 2. IP Settings
Select the IP setting
according to your
network: DHCP,
Static IP, or PPPoE.
- 27 -
Step 3. Email Settings
Enter the required
information to be
able to send email
with image.
- 28 -
Step 4. Wireless Networking (for TV-IP212W/TV-IP312W only)
Select Enable to
enable the wireless
function of the
camera, and then
complete the
required settings.
- 29 -
Step 5. Confirm Settings
This step shows all
the setting
information.
This step shows the configuration of your camera. When you confirm
the settings, click Apply to finish the wizard and reboot the camera.
Otherwise, click Prev to go back to the previous step(s) and change
the settings; or click Cancel to end the wizard and discard the
changes.
- 30 -
4.3 Basic Setup
The Basic menu contains three sub-menus that provide the system
settings for the camera, such as the Camera Name, Location, Date &
Time, and User management.
- 31 -
Basic >> System

Basic
- Camera Name: Enter a descriptive name for the camera.
- Location: Enter a descriptive name for the location used by the
camera.

Indication LED
This item allows you to set the LED illumination as desired. There
are two options: Normal and OFF.
- 32 -
Basic >> Date & Time
v

Date & Time
- TimeZone: Select the proper time zone for the region from the
pull-down menu.
- Synchronize with PC: Select this option and the date & time
settings of the camera will be synchronized with the connected
computer.
- Synchronize with NTP Server: Select this option and the time
will be synchronized with the NTP Server. You need to enter the
IP address of the server and select the update interval in the
following two boxes.
- Manual: Select this option to set the date and time manually.
- 33 -
Basic >> User

Administrator
To prevent unauthorized access to the camera’s Web
Configuration, you are strongly recommend to change the
default administrator password. Type the administrator password
twice to set and confirm the password.

General User
- User Name: Enter the user’s name you want to add to use the
camera.
- Password: Enter the password for the new user.
When you are finished, click Add/Modify to add the new user
to the camera. To modify the user’s information, select the one
you want to modify from User List and click Add/Modify.
- User List: Display the existing users of the camera. To delete a
user, select the one you want to delete and click Delete.
- 34 -

Guest
- User Name: Enter the guest’s name you want to add to use the
camera.
- Password: Enter the password for the new guest.
- User List: Display the existing guests of the camera. To delete a
user, select the one you want to delete and click Delete.

Direct Video Stream Authentication:
Enabled = Direct link to the video stream prompts for
authentication.
Disable = Direct link to video does not prompt for
authentication for ease of use when implementing or
embedding the video stream into a custom application or
webpage.
Examples of the Direct Link to video:
MPEG4 Mode
http://camera_ip_address:port number/mpgview.htm
MJPEG Mode
http://camera_ip_address:port number/jpgview.htm
NOTE The “General User” can access the camera and control the
Function buttons of the camera’s Web Configuration; the
“Guest’ can only view the live view image from the main page
of the Web Configuration while accessing the camera. Only the
“Administrator” is allowed to configure the camera through
the Web Configuration.
- 35 -
4.4 Network Settings
The Network menu contains three sub-menus that provide the
network settings for the camera, such as the IP Setting, DDNS Setting,
IP Filter, and Wireless network.
- 36 -
Network >> Network

IP Setting
This item allows you to select the IP address mode and set up the
related configuration.
- DHCP: Select this option when your network uses the DHCP
server. When the camera starts up, it will be assigned an IP
address from the DHCP server automatically.
- 37 -
- Static IP: Select this option to assign the IP address for the
camera directly. You can use IPSetup to obtain the related
setting values.
IP
Enter the IP address of the camera. The default
setting is 192.168.10.30.
Subnet Mask
Enter the Subnet Mask of the camera. The
default setting is 255.255.255.0.
Default Gateway
Enter the Default Gateway of the camera. The
default setting is 192.168.10.1.
Primary/
Secondary DNS
DNS (Domain Name System) translates domain
names into IP addresses. Enter the Primary DNS
and Secondary DNS that are provided by ISP.
- PPPoE: Select this option when you use a direct connection via
the ADSL modem. You should have a PPPoE account from your
Internet service provider. Enter the User Name and Password.
The camera will get an IP address from the ISP as starting up.
NOTE Once the camera get an IP address from the ISP as starting up,
it automatically sends a notification email to you. Therefore,
when you select PPPoE as your connecting type, you have to
set up the email or DDNS configuration in advance.

DDNS Setting
With the Dynamic DNS feature, you can assign a fixed host and
domain name to a dynamic Internet IP address. Select the Enable
option to enable this feature. Then, select the Provider from the
pull-down list and enter the required information in the Host
Name, User Name, and Password boxes. Please note that you
have to sign up for DDNS service with the service provider first.

UPnP
- 38 -
The camera supports UPnP (Universal Plug and Play), which is a
set of computer network protocols that enable the device-todevice interoperability. In addition, it supports port auto mapping
function so that you can access the camera if it is behind an NAT
router or firewall. Select the Enable option to enable this feature.

Ports Number
- HTTP Port: The default HTTP port is 80.
- RTSP Port: Configure the transmission of streaming data within
the network. The default RTSP (Real Time Streaming Protocol)
port is 554.
NOTE If the camera is behind an NAT router of firewall, the suggested
to be used is from 1024 to 65535.
- 39 -
Network >> IP Filter
The IP Filter setting allows the administrator of the camera to limit the
users within a certain range of IP addresses to access the camera.

Start/End IP Address
Assign a range of IP addresses that are not allowed to access the
camera by entering the Start IP address and End IP address. When
you are finished, click Add to save the range setting. You can
repeat the action to assign multiple ranges for the camera.
For example, when you enter 192.168.10.50 in Start IP Address
and 192.168.10.80 in End IP Address, the user whose IP address
located within 192.168.10.50 ~ 192.168.10.80 will not be allowed
to access the camera.

Deny IP List
The list displays the range setting(s) of IP addresses that are not
allowed to access the camera. To clear the setting, select a range
of IP addresses from the list and click Delete.
- 40 -
Network >> Wireless Setting (for TV-IP312W only)

Wireless
The camera supports WLAN while you use the wireless network.
Select the Enable option to enable this feature.
- Network ID (SSID}: The default SSID setting is “TRENDnet”. To
connect the camera to a specified access point, set a SSID for
the camera to correspond with the access point’s ESS-ID. To
connect the camera to an
Ad-Hoc wireless workgroup, set the same wireless channel and
SSID to match with the computer’s configuration.
Click Site Survey to display the available wireless networks, so
that you can easily connect to one of the listed wireless
networks.
- 41 -
List of searching results
- Wireless Mode: Select the type of wireless communication for
the camera: Infrastructure or Ad-Hoc.
- Channel: Select the appropriate channel from the list.
- Authentication: Select the authentication method to secure
the camera from being used by unauthorized user: Open,
Shared-key, WPA-PSK, and WPA2-PSK. The following table
explains the four options:
Open
The default setting of Authentication mode, which
communicates the key across the network.
Shared-key
Allow communication only with other devices with
identical WEP settings.
WPA-PSK/
WPA2-PSK
WPA-PSK/WPA2-PSK is specially designed for the
users who do not have access to network
authentication servers. The user has to manually
enter the starting password in their access point or
gateway, as well as in each PC on the wireless
network.
If you select Open or Shared-key as the Authentication mode,
you need to complete the following settings:
- 42 -
Encryption: Select the WEP option to enable the data
encryption feature to secure the camera within the wireless
network.
Format: Once you enable the Encryption feature, you need
to determine the encryption format by selecting ASCII or
HEX. ASCII format causes each character you type to be
interpreted as an eight-bit value. Hex format causes each pair
of characters you type to be interpreted as an eight-bit value
in hexadecimal (base 16) notation.
Key Length: Select the WEP key length you use: 64 bits or
128 bits.
WEP Key 1/2/3/4: Enter the WEP key(s) in the following
boxes.
If you select WPA-PSK or WPA2-PSK as the Authentication
mode, you need to complete the following settings:
Encryption: Select TKIP or AES. TKIP (Temporal Key Integrity
Protocol) changes the temporal key every 10,000 packets to
insure much greater security than the standard WEP security.
AES (Advanced Encryption Standard) is used to ensure the
highest degree of security and authenticity for digital
information.
Pre-Shared Key: This is used to identify each other in the
network. Enter the name in the box, and this name must
match the Pre-shared key value in the remote device.
- 43 -
4.5 Setting up Video & Audio
The Video & Audio menu contains three sub-menus that provide the
video and audio settings for the camera.
Video & Audio >> Camera
- 44 -

Image Setting
- Brightness: Adjust the brightness level from 0 ~ 100.
- Contrast: Adjust the contrast level from 0 ~ 100.
- Saturation: Adjust the colors level from 0 ~ 100.
Click Default to restore the default settings of the three options
above.
- Mirror: Select the Horizontal option to mirror the image
horizontally. Select the Vertical option to mirror the image
vertically.
- Light Frequency: Select the proper frequency according to the
camera’s location: 50Hz, 60Hz, or Outdoor.

Overlay Setting
- Includes Date & Time: Select this option to display the date &
time stamp on the live view image.
- Enable Opaque: Select this option to set a black background
to the displayed date & time stamp.
- 45 -
Video & Audio >> Video

MPEG4
- Video Resolution: Select the desired video resolution from the
three formats: VGA, QVGA and QQVGA. The higher setting
(VGA) obtains better video quality while it uses more resource
within your network.
- Video Quality: Select the desired image quality from five levels:
Lowest, Low, Medium, High, and Highest.
- Frame Rate: Select a proper setting depending on your
network status.

MJPEG
- Video Resolution: Select the desired video resolution from the
three formats: VGA, QVGA and QQVGA. The higher setting
- 46 -
(VGA) obtains better video quality while it uses more resource
within your network.
- Video Quality: Select the desired image quality from five levels:
Lowest, Low, Medium, High, and Highest.
- Frame Rate: Select a proper setting depending on your
network status.
NOTE The camera supports both MPEG4 and MJPEG compression.
MJPEG capture the images in JPEG format, which require
higher bandwidth to view smooth video. The administrator
can control the bandwidth of each connection well through
the setting options above.

3GPP
The camera supports 3GPP specification. Select the Disable
option to disable this feature. Otherwise, select 3GPP Without
Audio or 3GPP With Audio to transfer the video clips without or
with audio.
If you use a mobile phone that supports 3GPP, you can also view
the real-time streaming image captured by the camera on your
phone (with the default player on the phone) by entering the
RTSP link: rtsp://(IP address of the camera)/3gp.
- 47 -
Video & Audio >> Audio

Camera Microphone In
Select the Enable option to enable the camera’s audio function,
so that you can receive the on-site sound and voice from the
camera.

Camera Speaker Out
Select the Enable option to enable the camera’s external speaker
function, so that the connected speaker can play the sound and
voice through the camera.
- Volume: Set the speaker’s volume.
- 48 -
4.6 Event Server Configuration
The Event Server menu contains three sub-menus that allow you to
upload images to FTP, send emails that include still images, and store
the images to a NAS system.
When you complete the required settings for FTP, Email, or Network
Storage, click Test to test the related configuration is correct or not.
Once the camera connects to the server successfully, click Apply.
- 49 -
Event Server Setting>> FTP

FTP
- Host Address: Enter the IP address of the target FTP server.
- Port Number: Enter the port number used for the FTP server.
- User Name: Enter the user name to login into the FTP server.
- Password: Enter the password to login into the FTP server.
- Directory Path: Enter the destination folder for uploading the
images. For example, /Test/.
- Passive Mode: Select the Enable option to enable passive
mode.
- 50 -
Event Server Setting >> Email

Email
- SMTP Server Address: Enter the mail server address. For
example, mymail.com.
- Sender Email Address: Enter the email address of the user
who will send the email. For example, [email protected]
- Sender User Name: Enter the user name to login the mail
server.
- Sender Password: Enter the password to login the mail server.
- Receiver #1 Email Address: Enter the first email address of the
user who will receive the email.
- Receiver #2 Email Address: Enter the second email address of
the user who will receive the email.
- 51 -
Event Server Setting >> Network Storage

Net Storage
- Samba Server Address: Enter the IP address of the Network
Storage server. For example: 192.168.10.51.
- Share: Assign the folder on the Network Storage server to
share the files to users. For example, SAC7001-e1.
- Path: Assign the path for uploading the files on the Network
Storage server. For example, /ts-u200 /.
- User Name: Enter the user name to login into the Network
Storage server.
- Password: Enter the password to login into the Network
Storage server.
- Split By: When the file is too large to upload smoothly, use this
option to split it by selecting File Size or Recording Time.
- 52 -
- When Disk Full: Select Stop Recording or Recycle – Delete
Oldest Folder of File when the storage space on the Network
Storage server is full.
- 53 -
4.7 Motion Detect
The Motion Detect menu contains the command and option that
allow you to enable and set up the motion detection feature of the
camera. The camera provides two detecting areas.
To enable the detecting area, select Window 1 or 2 from the pulldown list, and then select Enable. When the detecting area is enabled,
you can use the mouse to move the detecting area and change the
area coverage.
- 54 -
- Name: Assign a name to the detecting area.
- Threshold: Move the slide bar to adjust the level for detecting
motion to record video.
- 55 -
4.8 Event Config
The Event Config menu contains four sub-menus that provide the
commands to configure event profiles.
- 56 -
Event Configuration >> General Setting
- Snapshot/Recording Filename Prefix: You can assign a given
prefix to each new captured file. Otherwise, leave this option
blank to use the default setting.
- Network Storage Recording Time Per Even: Limit the
recording time while you are using the Network Storage
solution.
Event Configuration >> Arrange Schedule Profile
This sub-menu displays the scheduled profile(s). To customize the
profile, click Add and then enter a descriptive name for the profile in
the prompt dialog window.
- 57 -
After entering the profile name, click OK and the profile is added to
the Schedule Profiles list. To delete the profile, select the profile in the
list and click Delete.
- Profile Name: Display the profile name that you select in the
Schedule Profiles list.
- Weekdays: Select the weekday(s) that you want to separately
assign in the schedule profile. The weekday that has been
assigned will be displayed with green color.
- 58 -
- Time List: Display the time period that you have assigned
within the selected weekday. To assign the same time period to
every weekday, click Add this to all weekdays; click Delete
this from all weekdays to remove the selected time period
from every weekday. Click Delete to remove the selected time
period.
- Start/End Time: Enter the start and end time and then click
Add to assign a time period within in the selected weekday.
Event Configuration >> Motion Detect Trigger
Select the Enable option to enable the trigger function of the camera,
so that you can send captured images within the detecting area to the
FTP server, email receiver, Network Storage server, or the connected
USB device. You have to configure corresponding settings, such as
FTP server and email server, to enable this feature.
- Schedule Profile: Select a schedule profile from the pull-down
list.
- 59 -
- Action: Select the destination that the captured images will be
sent to: Send Email, FTP Upload, Record to Network Storage,
or Save Image to USB.
Event Configuration >> Schedule Trigger
You can separately configure the schedule for trigger function of the
camera by Email, FTP, or Network Storage. Select the Enable option
on each item, and then select a Schedule Profile from the pull-down
list and set the Interval time.
NOTE If the setting value of the Network Storage Recording Time
per Event option in General Setting is longer than the Interval
time in Network Storage Schedule, the recorded file will be a
continuous video clip.
For example, if you set the Network Storage Recording Time
Per Event as 10 seconds and the Interval as 5 seconds,
- 60 -
recorded file becomes a non-stop video clip because the
camera will record a 10-second video clip every 5 seconds.
- 61 -
4.9 Tools
The Tools menu provides the commands that allow you to restart or
reset the camera. You can also backup and restore your configuration,
and upgrade the firmware for the camera.
- 62 -

Factory Reset
Click Reset to restore all factory default settings for the camera.

System Reboot
Click Reboot to restart the camera just like turning the device off
and on. The camera configuration will be retained after rebooting.

Configuration
You can save your camera configuration as a backup file on your
computer. Whenever you want to resume the original settings,
you can restore them by retrieving the backup file.
- Backup: Click Get the backup file to save the current
configuration of the camera.
- Restore: Click Browse to locate the backup file and then click
Restore.

Update Firmware
This item displays the current firmware version. You can upgrade
the firmware for your camera once you obtained a latest version
of firmware.
- Select the firmware: Click Browse to locate the backup file
and then click Update.
NOTE Make sure to keep the camera connected to the power source
during the process of upgrading firmware. Otherwise, the
camera might be damaged because of failure of upgrading
firmware.
- 63 -
4.10 USB
The USB menu provides the information and controls of the
connected USB device.

USB Dismount
To safely remove the connected USB device, you can press the
Unmount button for four seconds on the camera or click
Dismount from this item.

USB Information
Display the Total space and Free space of the USB device.
- 64 -

USB Setting
- When Disk Full: Select Stop Recording or Recycle – Delete
Oldest Folder of File when the storage space on the USB
device is full.
NOTE The connected USB storage device can be only used to store
still images.
- 65 -
4.11 Information
The Information menu displays the current configuration and events
log of the camera.

Device Info
Display the Basic, Video & Audio, Network, and Wireless settings
of the camera.
- 66 -

System Log
The Logs table displays the events log recorded by the system.
- 67 -
C HAPTER 5
S ECUR V IEW ™ S OFTWARE
This Chapter describes detail instructions on operating SecurView™
software, a useful friendly application for ease of control and
navigation requirement.
5.1
INSTALLATION
1. Insert the Installation CD-ROM into your computer’s CD-ROM
drive to initiate the Auto-Run program.
2. Click the SecurView from the Auto-Run menu screen.
- 68 -
NOTE To use SecurView™, you must have Microsoft .NET Framework
2.0 installed in the computer. The setup wizard will detect it
and, if the program is not installed yet, ask you to install it
during the process of installing SecurView™.
- 69 -
3. Then SecurView Setup Wizard will appear. Click “Next” when the
Welcome to the SecurView Setup Wizard appears
- 70 -
4. Click “Browse” to choose the desired destination location. By
default, the destination location is C:\Program
Files\TRENDnet\SecurView. Then Click “Next”.
- 71 -
5. Click “Next” to confirm the SecurView software to be installed to
the computer.
- 72 -
6. Click t When the Installation Complete window appears, click
“Close”.
7. After installing the IPSetup utility, the application is automatically
installed to your computer, and creates a folder in “ Start
\Program\TRENDnet\SecurView”.
- 73 -
5.2
1.
USING INSTALLATION
To launch the program, click Start > Program > TRENDnet >
SecurView, and then click SecruView™. The main screen will
appear as below.
NOTE Please set the resolution to 1024x768 or above on your
computer while using SecurView™; otherwise, the displayed
main screen may be distorted.
- 74 -
Item features
The following describes the function of each item on the main screen:

CONTROLS Panel
- SETTING: Click to enter the Setting screen of SecurView™. Click
again to return to the main screen of SecurView™.
- PLAY: Click to play the recorded video file using the media
player on the computer (for example, Windows Media Player by
default).
- LOCK: Click to lock the camera controls. Click again to resume
controls for the camera. If you have set ID and Password in
SETTING > Account, you will be asked to enter the required
- 75 -
information to unlock.
- ALL RECORD: Click to start recording video clips using ALL
connected cameras. To stop recording, please click Record
button
to stop the individual camera. Please note: stop
recording only stop the manual recording camera. For
schedule recording, please change the setting on configuration.
TIP
By default, the ID and Password boxes are “blank.” Click
SETTING > Account to change the ID and password of
lock/unlock function.
- 76 -

VIEW SELECTION Panel
- View mode buttons: SecurView™ provides multiple view
modes, including 1/4/9/16 windows and Full screen mode.
- SCAN: When multiple cameras connected, click this button to
display the video views between cameras. Click the Scan
button again to stop scanning.
- PREV: When multiple cameras connected, click this button to
switch the video view to the previous camera.
- NEXT: When multiple cameras connected, click this button to
switch the video view to the next camera.
TIP
To set the time interval of scanning, click SETTING > Other
and then adjust the time from 1 to 10 seconds in the Time
interval of scan option.
- 77 -

CAMERA Panel
- TRIGGER OUT: Click to turn on the trigger out connector of the
camera. This button is available only when the connected
camera supports the trigger out connector, which is used to
control the external device connected to the camera, such as a
light.
- SNAPSHOT: Click to capture a still image using the selected
camera and save the file in the computer.
- RECORD: Click to start recording a video clip using the selected
camera. Click again to stop recording and save the file in the
computer.
- TALK: Click to speak out through the camera. Please note only
one user is allowed to use this function at the same time.
- LISTEN: Click to receive the on-site sound and voice from the
camera.
- 78 -

SYSTEM Panel
This panel displays the current date and time.

PAN-TILT CONTROL Panel (optional)
When you connect a pan/tilt camera, the system will detect the
camera’s function automatically and the PAN-TILT CONTROL
buttons will become functional. Otherwise, these buttons are
displayed as gray out buttons.
- Direction/Home buttons: Click these buttons to adjust the
camera’s viewing angle to Up (
) / Down (
) / Left (
/ Right (
) / Left-Up (
) / Left-Down (
) / Right-Up
(
) / Right-Down (
).
Click the Home button (
default position.
) to return the camera to the
- SWING: If you have saved two or more positions for the
selected camera, click this button to control the camera
swinging from one position to another position.
- 79 -
)

Video View Window and Camera List
Video Viewing
Window
Camera List
- Video Viewing Window: This window displays the video view
of the selected camera, which can be divided into 4/9/16
windows according to your selection in VIEW SELECTION panel.
- Camera List: This list displays the information of the connected
camera(s).
- 80 -
To add a camera
1. Click SETTING in the CONTROLS panel to display the Setting
screen.
2. Click Add New Camera.
- 81 -
3. In the pop-up Add New Camera dialog window, you can:
 Select the Search tab if you are not sure of the camera’s IP
address. Click Search camera to search the available camera
within the network. Once the camera is found and is shown
in the list, select it and click Add Camera.
 Select the Input tab to add a camera by entering its IP
address directly. Enter the camera’s IP address (default:
192.168.10.30) and Port (default: 80), and then click Add
Camera.
- 82 -
4. Enter the User name and Password for the camera, and then click
OK. The connected camera will be displayed in the Camera List.
- 83 -
5. Click SETTING to return to the Video View Window. The video
view of the selected camera will be displayed now.
To remove a camera
1. Click SETTING in the CONTROLS panel to display the Setting
screen.
2. Select a camera from the list and click Delete Camera.
- 84 -
Select a camera
Delete the camera
To link to the Web page of the camera
Click SETTING > Camera List > Camera Configuration and then Link
web page to launch the Web browser that displays live view image
and Web Configuration of the selected camera.
- 85 -
To record video
SecurView™ provides three methods to record video clips: one is to
click the RECORD/All Record button to record manually; the second
is to record by motion detection; the third is to set the recording
schedule in Setting > Recording Configuration > Schedule
Recording Configuration.

Manually recording
Click RECORD/All Record and it starts recording. Click the
button again to stop.
- 86 -

Trigger recording by motion detection
When the motion detection function of the selected camera is
enabled, you can configure the camera to start recording
triggered by the motion detected. Click SETTING > Motion
Configuration, and then select the Recording option to
enable the selected camera to record by motion detection.
- 87 -

Schedule recording Configuration
This recording method will work after you have completed the
required settings in Schedule Recording Configuration. The
recording schedule can be defined by Dates or Days.
- Dates: Select the camera from the pull-down list..
- 88 -
Select a camera
Add Schedule
- Then, click Add to set the Start/Stop date and time and then
click OK to add the recording schedule to the list.
- Click Apply to save the settings
- 89 -
- 90 -
Days: First, select the camera from the pull-down list and select
Days tab. Then, select the weekday from the day buttons and
then set the time period. Click Apply to save the settings.
- 91 -
To configure the recording settings
To configure the recording settings, including the storage folder and
storage options, click SETTING > Recording Configuration.

Recording File Path: To change the destination folder to save
the recorded video file, click Browse under the Recording File
Path box to assign a new folder.

Each Recording File Size: This option allows you to select from
20 to 100 MB so that the video will be recorded as another file
automatically when the recording file reaches the specified size
limit.
- 92 -

Reserved HDD space for each camera: This option allows you
to set to reserve the storage space on the hard disk drive for the
recording of each camera. Before setting the reserve space on
the hard disk drive, you can check the available storage space
that is displayed in the HDD Free space field.

Enable Recycle Recording: Click on the camera number to
clear the files when the unreserved space of the hard disk drive
is full.
To playback the recorded video
The recorded video clips are saved in your computer, and can be
played using the media player on the computer, such as Windows
Media Player. To start playback, simply click the PLAY button on the
CONTROLS panel, and the following dialog screen will appear,
allowing you to select the file to playback.
Select the recorded video file under the [camera] path and then click
Open to launch the media player to playback.
- 93 -
NOTE If your player on the computer don’t have video codec to
playback the recorded video. You can download video codec
from http://www.xvid.org/downloads.15.0.html to support.
To set up motion detection options
When the motion detection function of the selected camera is
enabled, you can set the Motion Options by selecting Alarm,
Recording, Send e-Mail, and Trigger Out under SETTING > Motion
Configuration.
- 94 -

Alarm: Select Beep or Music to alert you for the motion
detected. When you select Music, you can customize the sound
by clicking Browse and then selecting your favorite music
(*.wav or *.mp3 file) in the computer.

Recording: Select this option to enable the camera to record
by motion detected.

Send Email: Select this option so that the system will be able to
send an email to the specified receiver. Once the option is
selected, you have to complete the required information in
SETTING > Motion Configuration > Email Configuration.
- Mail Server: Enter the mail server address. For example,
mymail.com.
- 95 -
- Mail From: Enter the email address of the user who will send
the email. For example, [email protected]
- Mail To: Enter the email address of the user who will receive
the email.
- User Name: Enter the user name to login the mail server.
- Password: Enter the password to login the mail server.
- Subject: Enter a subject for the notification email.

Trigger Out: If the selected camera supports Trigger Out
connector, select this option to enable the Trigger Out function.
Account
Click SETTING > Account to setup the username & password to lock &
unlock the main screen of the SecurView.
Other
Click SETTING > Other to setup the scanning time between cameras.
The default setting is 2 seconds. You can set the interval time
between 2 ~ 20 seconds.
- 96 -
- 97 -
Information
Click SETTING > About to display the information of the software
application.
- 98 -
C HAPTER 6
A PPENDIX
A.1 Specification




Image Sensor
Sensor
Resolution
1/4” color CMOS
640x480
Video
Compression
Video resolution
MPEG4/MJPEG
VGA/QVGA/QQVGA; 30fps max.
System Hardware
Processor
RAM
ROM
Power
ARM9 base
32MB SDRAM
8MB NOR Flash
DC 5V, 2.5AV
Communication
LAN
WLAN
Protocol support
10/100Mbps Fast Ethernet, auto-sensed,
Auto-MDIX
IEEE 802.11b/g
TCP/IP, UDP, ICMP, DHCP, NTP, DNS, DDNS,
SMTP, FTP, Samba, PPPoE, UPnP, RTP, RTSP,
RTCP
- 99 -



User Interface
LAN
Antenna
Reset
USB
LEDs
One RJ-45 port
One detachable antenna
One reset button
USB 1.1 port, with one unmount button;
Power distribution: 500mA Max.
Support FAT,FAT32 file system
Power LED (orange); Link LED (green)
Audio
Input
Output
Codec
Built-in MIC
Headphone 3.5mm output jack (Mono)
PCM/AMR (AMR is for 3GPP only)
SecurView™ Software
OS Support
Windows 7(32-bit) /Vista (32-bit)/ XP (32bit) / 2000
Feature
playback/recording/configuration features

Web Configuration
OS Support
Windows 7/Vista/XP/2000
Browser
Internet Explorer 5.0 or above

Operating Environment
Temperature
- Operation: 5°C ~ 45°C
- Storage: -15°C ~ 60°C
Humidity
- Operation: 20% ~ 85% non-condensing
- Storage: 0% ~ 90% non-condensing
- 100 -
A.2 Glossary of Terms
NUMBERS
10BASE-T
10BASE-T is Ethernet over UTP Category III, IV, or V
unshielded twisted-pair media.
100BASE-TX
The two-pair twisted-media implementation of 100BASET is called 100BASE-TX.
A
ADPCM
Adaptive Differential Pulse Code Modulation, a new
technology improved from PCM, which encodes analog
sounds to digital form.
AMR
AMR (Adaptive Multi-Rate) is an audio data compression
scheme optimized for speech coding, which is adopted as
the standard speech codec by 3GPP.
Applet
Applets are small Java programs that can be embedded in
an HTML page. The rule at the moment is that an applet
can only make an Internet connection to the computer
form that the applet was sent.
ASCII
American Standard Code For Information Interchange, it
is the standard method for encoding characters as 8-bit
sequences of binary numbers, allowing a maximum of 256
characters.
ARP
Address Resolution Protocol. ARP is a protocol that resides
at the TCP/IP Internet layer that delivers data on the same
network by translating an IP address to a physical address.
AVI
Audio Video Interleave, it is a Windows platform audio
and video file type, a common format for small movies
and videos.
B
BOOTP
Bootstrap Protocol is an Internet protocol that can
automatically configure a network device in a diskless
- 101 -
workstation to give its own IP address.
C
Communication
Communication has four components: sender, receiver,
message, and medium. In networks, devices and
application tasks and processes communicate messages
to each other over media. They represent the sender and
receivers. The data they send is the message. The cabling
or transmission method they use is the medium.
Connection
In networking, two devices establish a connection to
communicate with each other.
D
DHCP
Developed by Microsoft, DHCP (Dynamic Host
Configuration Protocol) is a protocol for assigning
dynamic IP addresses to devices on a network. With
dynamic addressing, a device can have a different IP
address every time it connects to the network. In some
systems, the device's IP address can even change while it
is still connected. It also supports a mix of static and
dynamic IP addresses. This simplifies the task for network
administrators because the software keeps track of IP
addresses rather than requiring an administrator to
manage the task. A new computer can be added to a
network without the hassle of manually assigning it a
unique IP address. DHCP allows the specification for the
service provided by a router, gateway, or other network
device that automatically assigns an IP address to any
device that requests one.
DNS
Domain Name System is an Internet service that translates
domain names into IP addresses. Since domain names are
alphabetic, they're easier to remember. The Internet
however, is really based on IP addresses every time you
use a domain name the DNS will translate the name into
the corresponding IP address. For example, the domain
name www.network_camera.com might translate to
- 102 -
192.167.222.8.
E
Enterprise
network
An enterprise network consists of collections of networks
connected to each other over a geographically dispersed
area. The enterprise network serves the needs of a widely
distributed company and operates the company’s
mission-critical applications.
Ethernet
The most popular LAN communication technology. There
are a variety of types of Ethernet, including 10Mbps
(traditional Ethernet), 100Mbps (Fast Ethernet), and
1,000Mbps (Gigabit Ethernet). Most Ethernet networks
use Category 5 cabling to carry information, in the form of
electrical signals, between devices. Ethernet is an
implementation of CSMA/CD that operates in a bus or star
topology.
F
Fast Ethernet
Fast Ethernet, also called 100BASE-T, operates at 10 or
100Mbps per second over UTP, STP, or fiber-optic media.
Firewall
Firewall is considered the first line of defense in
protecting private information. For better security, data
can be encrypted. A system designed to prevent
unauthorized access to or from a private network.
Firewalls are frequently used to prevent unauthorized
Internet users from accessing private networks connected
to the Internet, especially Intranets all messages entering
or leaving the intranet pass through the firewall, which
examines each message and blocks those that do not
meet the specified security criteria.
G
Gateway
A gateway links computers that use different data formats
together.
- 103 -
Group
Groups consist of several user machines that have similar
characteristics such as being in the same department.
H
HEX
Short for hexadecimal refers to the base-16 number
system, which consists of 16 unique symbols: the
numbers 0 to 9 and the letters A to F. For example, the
decimal number 15 is represented as F in the hexadecimal
numbering system. The hexadecimal system is useful
because it can represent every byte (8 bits) as two
consecutive hexadecimal digits. It is easier for humans to
read hexadecimal numbers than binary numbers.
I
Intranet
This is a private network, inside an organization or
company that uses the same software you will find on the
public Internet. The only difference is that an Intranet is
used for internal usage only.
Internet
The Internet is a globally linked system of computers that
are logically connected based on the Internet Protocol
(IP). The Internet provides different ways to access private
and public information worldwide.
Internet address To participate in Internet communications and on Internet
Protocol-based networks, a node must have an Internet
address that identifies it to the other nodes. All Internet
addresses are IP addresses
IP
Internet Protocol is the standard that describes the layout
of the basic unit of information on the Internet (the
packet) and also details the numerical addressing format
used to route the information. Your Internet service
provider controls the IP address of any device it connects
to the Internet. The IP addresses in your network must
conform to IP addressing rules. In smaller LANs, most
people will allow the DHCP function of a router or
gateway to assign the IP addresses on internal networks.
- 104 -
IP address
IP address is a 32-binary digit number that identifies each
sender or receiver of information that is sent in packets
across the Internet. For example 80.80.80.69 is an IP
address. When you “call” that number, using any
connection methods, you get connected to the computer
that “owns” that IP address.
ISP
ISP (Internet Service Provider) is a company that maintains
a network that is linked to the Internet by way of a
dedicated communication line. An ISP offers the use of its
dedicated communication lines to companies or
individuals who can’t afford the high monthly cost for a
direct connection.
J
JAVA
Java is a programming language that is specially designed
for writing programs that can be safely downloaded to
your computer through the Internet without the fear of
viruses. It is an object-oriented multi-thread programming
best for creating applets and applications for the Internet,
Intranet and other complex, distributed network.
L
LAN
Local Area Network a computer network that spans a
relatively small area sharing common resources. Most
LANs are confined to a single building or group of
buildings.
M
MJPEG
MJPEG (Motion JPEG) composes a moving image by
storing each frame of a moving picture sequence in JPEG
compression, and then decompressing and displaying
each frame at rapid speed to show the moving picture.
MPEG4
MPEG4 is designed to enable transmission and reception
of high-quality audio and video over the Internet and
- 105 -
next-generation mobile telephones.
N
NAT
Network Address Translator generally applied by a router
that makes many different IP addresses on an internal
network appear to the Internet as a single address. For
routing messages properly within your network, each
device requires a unique IP address. But the addresses
may not be valid outside your network. NAT solves the
problem. When devices within your network request
information from the Internet, the requests are forwarded
to the Internet under the router's IP address. NAT
distributes the responses to the proper IP addresses
within your network.
Network
A network consists of a collection of two or more devices,
people, or components that communicate with each
other over physical or virtual media. The most common
types of network are:
LAN – (local area network): Computers are in close
distance to one another. They are usually in the same
office space, room, or building.
WAN – (wide area network): The computers are in
different geographic locations and are connected by
telephone lines or radio waves.
NWay Protocol
A network protocol that can automatically negotiate the
highest possible transmission speed between two
devices.
P
PCM
PCM (Pulse Code Modulation) is a technique for
converting analog audio signals into digital form for
transmission.
PING
Packet Internet Groper, a utility used to determine
whether a specific IP address is accessible. It functions by
sending a packet to the specified address and waits for a
- 106 -
reply. It is primarily used to troubleshoot Internet
connections.
PPPoE
Point-to-Point Protocol over Ethernet. PPPoE is a
specification for connecting the users on an Ethernet to
the Internet through a common broadband medium,
such as DSL or cable modem. All the users over the
Ethernet share a common connection.
Protocol
Communication on the network is governed by sets of
rules called protocols. Protocols provide the guidelines
devices use to communicate with each other, and thus
they have different functions. Some protocols are
responsible for formatting and presenting and presenting
data that will be transferred from file server memory to
the file server’s net work adapter Others are responsible
for filtering information between networks and
forwarding data to its destination. Still other protocols
dictate how data is transferred across the medium, and
how servers respond to workstation requests and vice
versa. Common network protocols responsible for the
presentation and formatting of data for a network
operating system are the Internetwork Packet Exchange
(IPX) protocol or the Internet Protocol (IP). Protocols that
dictate the format of data for transferors the medium
include token-passing and Carrier Sense Multiple Access
with Collision Detection (CSMA/CD), implemented as
token-ring, ARCNET, FDDI, or Ethernet. The Router
Information Protocol (RIP),a part of the Transmission
Control Protocol/Internet Protocol (TCP/IP) suite, forwards
packets from one network to another using the same
network protocol.
R
RJ-45
RJ-45 connector is used for Ethernet cable connections.
Router
A router is the network software or hardware entity
charged with routing packets between networks.
RTP
RTP (Real-time Transport Protocol) is a data transfer
- 107 -
protocol defined to deliver live media to the clients at the
same time, which defines the transmission of video and
audio files in real time for Internet applications.
RTSP
RTSP (Real-time Streaming Protocol) is the standard used
to transmit stored media to the client(s) at the same time,
which provides client controls for random access to the
content stream.
S
Server
It is a simple computer that provides resources, such as
files or other information.
SIP
SIP (Session Initiated Protocol) is a standard protocol that
delivers the real-time communication for Voice over IP
(VoIP), which establishes sessions for features such as
audio and video conferencing.
SMTP
The Simple Mail Transfer Protocol is used for Internet mail.
SNMP
Simple Network Management Protocol. SNMP was
designed to provide a common foundation for managing
network devices.
Station
In LANs, a station consists of a device that can
communicate data on the network. In FDDI, a station
includes both physical nodes and addressable logical
devices. Workstations, single-attach stations, dual-attach
stations, and concentrators are FDDI stations.
Subnet mask
In TCP/IP, the bits used to create the subnet are called the
subnet mask.
T
(TCP/IP)
Transmission Control Protocol/Internet Protocol is a
widely used transport protocol that connects diverse
computers of various transmission methods. It was
developed y the Department of Defense to connect
different computer types and led to the development of
the Internet.
- 108 -
Transceiver
A transceiver joins two network segments together.
Transceivers can also be used to join a segment that uses
one medium to a segment that uses a different medium.
On a 10BASE-5 network, the transceiver connects the
network adapter or other network device to the medium.
Transceivers also can be used on 10BASE-2 or 10BASE-T
networks to attach devices with AUI ports.
U
UDP
The User Datagram Protocol is a connectionless protocol
that resides above IP in the TCP/IP suite
User Name
The USERNAME is the unique name assigned to each
person who has access to the LAN.
Utility
It is a program that performs a specific task.
UTP
Unshielded twisted-pair. UTP is a form of cable used by all
access methods. It consists of several pairs of wires
enclosed in an unshielded sheath.
W
WAN
Wide-Area Network. A wide-area network consists of
groups of interconnected computers that are separated
by a wide distance and communicate with each other via
common carrier telecommunication techniques.
WEP
WEP is widely used as the basic security protocol in Wi-Fi
networks, which secures data transmissions using 64-bit
or 128-bit encryption.
Windows
Windows is a graphical user interface for workstations
that use DOS.
WPA
WPA (Wi-Fi Protected Access ) is used to improve the
security of Wi-Fi networks, replacing the current WEP
standard. It uses its own encryption, Temporal Key
Integrity Protocol (TKIP), to secure data during
transmission.
WPA2
Wi-Fi Protected Access 2, the latest security specification
- 109 -
that provides greater data protection and network access
control for Wi-Fi networks. WPA2 uses the governmentgrade AES encryption algorithm and IEEE 802.1X-based
authentication, which are required to secure large
corporate networks.
- 110 -
Limited Warranty
TRENDnet warrants its products against defects in material
and workmanship, under normal use and service, for the
following lengths of time from the date of purchase.
TV-IP312/TV-IP312W – 3 Years Warranty
AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1
year warranty.
If a product does not operate as warranted during the
applicable warranty period, TRENDnet shall reserve the
right, at its expense, to repair or replace the defective
product or part and deliver an equivalent product or part to
the customer. The repair/replacement unit’s warranty
continues from the original date of purchase. All products
that are replaced become the property of TRENDnet.
Replacement products may be new or reconditioned.
TRENDnet does not issue refunds or credit. Please contact
the point-of-purchase for their return policies.
TRENDnet shall not be responsible for any software,
firmware, information, or memory data of customer
contained in, stored on, or integrated with any products
returned to TRENDnet pursuant to any warranty.
There are no user serviceable parts inside the product. Do
not remove or attempt to service the product by any
- 111 -
unauthorized service center. This warranty is voided if (i)
the product has been modified or repaired by any
unauthorized service center, (ii) the product was subject to
accident, abuse, or improper use (iii) the product was
subject to conditions more severe than those specified in
the manual.
Warranty service may be obtained by contacting TRENDnet
within the applicable warranty period and providing a copy
of the dated proof of the purchase. Upon proper
submission of required documentation a Return Material
Authorization (RMA) number will be issued. An RMA
number is required in order to initiate warranty service
support for all TRENDnet products. Products that are sent
to TRENDnet for RMA service must have the RMA number
marked on the outside of return packages and sent to
TRENDnet prepaid, insured and packaged appropriately for
safe shipment. Customers shipping from outside of the USA
and Canada are responsible for return shipping fees.
Customers shipping from outside of the USA are
responsible for custom charges, including but not limited
to, duty, tax, and other fees.
WARRANTIES EXCLUSIVE: IF THE TRENDNET PRODUCT
DOES NOT OPERATE AS WARRANTED ABOVE, THE
CUSTOMER’S SOLE REMEDY SHALL BE, AT TRENDNET’S
OPTION, REPAIR OR REPLACE. THE FOREGOING
WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN
- 112 -
LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,
EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR
OTHERWISE,
INCLUDING
WARRANTIES
OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. TRENDNET NEITHER ASSUMES NOR AUTHORIZES
ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER
LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION
MAINTENANCE OR USE OF TRENDNET’S PRODUCTS.
TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY
IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE
ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR
WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S
MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING,
UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY, OR
ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED
USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER
HAZARD.
LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED
BY LAW TRENDNET ALSO EXCLUDES FOR ITSELF AND ITS
SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT
OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL,
CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE
DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR
PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR
DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN
CONNECTION
WITH
THE
SALE,
INSTALLATION,
- 113 -
MAINTENANCE, USE, PERFORMANCE, FAILURE, OR
INTERRUPTION OF THE POSSIBILITY OF SUCH DAMAGES,
AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR
REFUND OF THE PURCHASE PRICE PAID, AT TRENDNET’S
OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES
WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN
SHALL FAIL OF ITS ESSENTIAL PURPOSE.
Governing Law: This Limited Warranty shall be governed by
the laws of the state of California.
Some TRENDnet products include software code written by
third party developers. These codes are subject to the GNU
General Public License ("GPL") or GNU Lesser General
Public License ("LGPL").
Go to http://www.trendnet.com/gpl or
http://www.trendnet.com Download section and look for
the desired TRENDnet product to access to the GPL Code or
LGPL Code. These codes are distributed WITHOUT
WARRANTY and are subject to the copyrights of the
developers. TRENDnet does not provide technical support
for these codes. Please go to
http://www.gnu.org/licenses/gpl.txt or
http://www.gnu.org/licenses/lgpl.txt for specific terms of
each license.
- 114 -
- 115 -
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement