- No category
advertisement
• FAST SHIPPING AND
DELIVERY
• TENS OF THOUSANDS OF
IN-STOCK ITEMS
• EQUIPMENT DEMOS
• HUNDREDS OF
MANUFACTURERS
SUPPORTED
• LEASING/MONTHLY
RENTALS
• ITAR CERTIFIED
SECURE ASSET SOLUTIONS
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment
SERVICE CENTER REPAIRS
Experienced engineers and technicians on staff at our full-service, in-house repair center
Instra
View
SM REMOTE INSPECTION
Remotely inspect equipment before purchasing with our interactive website at www.instraview.com
WE BUY USED EQUIPMENT
Sell your excess, underutilized, and idle used equipment
We also offer credit for buy-backs and trade-ins www.artisantg.com/WeBuyEquipment
LOOKING FOR MORE INFORMATION?
Visit us on the web at www.artisantg.com
for more information on price quotations, drivers, technical specifications, manuals, and documentation
Contact us: (888) 88-SOURCE | [email protected] | www.artisantg.com
TC-510 Pressure Control Unit
® AT THE HEART OF SENSOR INNOVATION®
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
TC-510 Pressure Control Unit
The TC-510 Pressure Control Unit a passive interface between the Millar Mikro-Tip catheter pressure transducer and strain gauge pressure monitors which supply bridge excitation voltage and have balance and calibration controls for full-bridge strain gauge pressure transducers. The TC-510 has an internal calibration circuit to provide an electrical zero as well as a 100 mmHg calibration signal. The output connector is a standard 9-pin sub-D. A separate monitor interface cable is required.
Pressure Control Unit Ordering Information
Input
Model Part Connector
Number Number Channels Type
TC-510 851-5918 One Viking
NOTE: Viking connectors are round with 4 pins.
Isolated
Input/Output
No
Output
Connector
Type
9 pin sub-D
Mikro-Tip Catheter Pressure Interface Cables
Mikro-Tip Pressure Catheters are provided with either Viking (4-pin) or Millar Low Profile (4-pin) connectors depending on the model purchased. Catheter models with Viking connectors may connect directly to the TC-510.
Connecting the catheter with a Viking connector directly to the control unit limits access to the subject or patient.
It is recommended that a TEC-10C interface cable be used between the catheter and control unit. All catheters with low profile pressure connectors require a TEC-10D interface cable to the control unit. Each pressure channel requires a separate interface cable and control unit.
Viking Connector
(TEC-10C)
Low Profile Connector
(TEC-10D)
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Adapter/Interface Cable Ordering Information
Cable
Model
TEC-5C
TEC-10C
TEC-10D
Number
850-1118
850-1108
850-1308
Length
5 ft. (152 cm)
10 ft. (304 cm)
10 ft. (304 cm)
Catheter End
Type
Viking
Viking
Low Profile
Control Unit
Connector
Type
Viking
Viking
Viking
NOTE: Viking connectors are round with 4 pins. Low Profile connectors are flat with 4 pins. The above flexible cables facilitate maneuvering the catheter during recording.
They may be sterilized and permit connection of a catheter to a Pressure Control Unit located outside the sterile field.
TC-510 Pressure Control Unit Output Cable
Control Unit
Cable Part Cable Connector
Model Number Length Type
TC-510 Output Monitor Cable 850-3008 6.5 ft. (198 cm) 9 pin sub-D
Monitor
Connector
Type
Open ended, not wired
NOTE: A selection is available from Millar of other TC-510 output cables that are wired for a variety of monitor and recorder inputs. Please contact our Customer Service
Department for availability.
When ordering please specify the following:
• Data Acquisition System/Recorder/Preamp/Coupler manufacturer. Example: Hewlett Packard
• Preamp/Coupler models. Example: 8805D
• Specify Connector and pin-out. Example: Hewlett Packard TWINAX or Cannon WK6-21C
• Indicate if an intermediate connector panel, i.e., “patch panel,” is to be used with the recorder.
TC-510 connectivity
TEC Cable
Pressure Input
TC-510
Interface Cable
Strain Gauge
Amplifier
DAQ or Monitor
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
World Headquarters
Millar Instruments, Inc.
6001-A Gulf Freeway
Houston, Texas 77023-5417 USA
Phone: 832-667-7000 or 800-669-2343 (in the USA)
Fax:
Email:
832-667-7001 [email protected]
Web site: www.millarinstruments.com
Millar Worldwide Distribution
Millar Instruments, Inc. has a network of Authorized Distributors in most countries around the world. For information on the Millar distributor in your country, please contact the Millar Customer Service Department at our headquarters in Houston.
Authorized Representative for the European Community
BOSA S.p.A.
Via Sardegna n°61
20146 Milano
Italy
Telephone: +39-02-48011-693
Fax: +39-02-468564
Email: [email protected]
® AT THE HEART OF SENSOR INNOVATION®
© 2002, 2004 Millar Instruments, Inc.
Millar, Mikro-Tip, and At the Heart of Sensor Innovation are registered trademarks of Millar Instruments, Inc.
Products and company names used are the trademarks or trade names of their respective companies.
Models referred to herein are protected by USA and International patents. All product specifications are subject to change without notice.
M.I. P/N 005-1050 Rev. --
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
• FAST SHIPPING AND
DELIVERY
• TENS OF THOUSANDS OF
IN-STOCK ITEMS
• EQUIPMENT DEMOS
• HUNDREDS OF
MANUFACTURERS
SUPPORTED
• LEASING/MONTHLY
RENTALS
• ITAR CERTIFIED
SECURE ASSET SOLUTIONS
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment
SERVICE CENTER REPAIRS
Experienced engineers and technicians on staff at our full-service, in-house repair center
Instra
View
SM REMOTE INSPECTION
Remotely inspect equipment before purchasing with our interactive website at www.instraview.com
WE BUY USED EQUIPMENT
Sell your excess, underutilized, and idle used equipment
We also offer credit for buy-backs and trade-ins www.artisantg.com/WeBuyEquipment
LOOKING FOR MORE INFORMATION?
Visit us on the web at www.artisantg.com
for more information on price quotations, drivers, technical specifications, manuals, and documentation
Contact us: (888) 88-SOURCE | [email protected] | www.artisantg.com
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project