PD0409J5050S2HF Datasheet RevA
Model PD0409J5050S2HF
Rev A
Ultra Low Profile 0805 Power Divider
50Ω to 50Ω
Description
The PD0409J5050S2HF is a low profile, sub-miniature Wilkinson power divider in
an easy to use surface mount package. The PD0409J5050S2HF is ideal for high
volume manufacturing and delivers higher performances than traditional printed and
lumped element solutions. The PD0409J5050S2HF is matched to 50 Ω and has a
height profile of 0.5 mm which is ideal for high level integrations in the following
markets: GSM, WCDMA, DVB-H (Europe) and Terrestrial TV.
The PD0409J5050S2HF does not include the resistive element and therefore,
requires an external resistor for operation. The PD0409J5050S2HF is available on
tape and reel for high volume manufacturing pick and place.
Detailed Electrical Specifications: Specifications subject to change without notice.
ROOM (25°°C)
Features:
•
•
•
•
•
•
•
•
•
•
400-900 MHz
0.5mm Height Profile
50Ω Input / 50Ω Outputs
Low Insertion Loss
Surface Mountable
Tape & Reel
Non-conductive Surface
RoHS Compliant
External Resistor required
Halogen Free
Parameter
Min.
Frequency
Input Port Impedance
Output Port Impedance
Return Loss
Insertion Loss*
Amplitude Balance
Phase Balance
Isolation (Output Ports)
Power Handling
Operating Temperature
400
Typ.
50
50
12.0
0.6
0.2
1.0
10.5
11
9
Max
Unit
900
MHz
Ω
Ω
dB
dB
dB
Degrees
dB
Watts
ºC
0.7
0.5
3
2
+85
-55
* Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC)
Outline Drawing
TOP VIEW (Near Side)
SIDE VIEW
BOTTOM VIEW (Far Side)
4x 0.37
2.04±0.10
1
0.55±0.06
2
3
2x 0.15
1.29±0.10
6x 0.98
Orientation Marker
Denotes Pin Location
Orientation Marker
Denotes Pin Location
Mechanical Outline
-Dimensions are in Millimeters
Pin
1
2
3
4
5
6
6x
0.22
6
5
4
4x 0.65
6x
0.30
Designation
GND
Input
GND
Output 1
GND
Output 2
Visit us at
www.anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model PD0409J5050S2HF
Rev A
Typical Broadband Performance: 10 MHz. to 8.0GHz.
Insertion Loss (dB)
0
-5
-0.5
-10
-1
Insertion Loss (dB)
Return Loss at Input Port (dB)
Return Loss at Input Port (dB)
0
-15
-20
-1.5
-2
-25
-2.5
-30
-3
-35
-3.5
1
2
3
4
Freq [GHz]
5
6
7
8
1
2
20
1.5
15
1
10
Phase balance(degree) 23
Amplitude Balance23 (dB)
4
Freq [GHz]
5
6
7
8
6
7
8
Phase balance(degree)
Amplitude Balance (dB)
2
0.5
0
-0.5
-1
5
0
-5
-10
-1.5
-2
3
-15
1
2
3
4
Freq [GHz]
5
6
7
8
5
6
7
8
-20
1
2
3
4
Freq [GHz]
5
Isolation (dB)
0
-5
Isolation 23(dB)
-10
-15
-20
-25
-30
-35
1
2
3
4
Freq [GHz]
Visit us at
www.anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model PD0409J5050S2HF
Rev A
Typical Performance: 300 MHz. to 1000 MHz.
Insertion Loss (dB)
0
-5
-0.5
-10
-1
Insertion Loss (dB)
Return Loss at Input Port (dB)
Return Loss at Input Port (dB)
0
-15
-20
-1.5
-2
-25
-2.5
-30
-3
-3.5
-35
0.4
0.5
0.6
0.7
Freq [GHz]
0.8
0.9
0.4
1
0.5
20
1.5
15
1
10
0.5
0
-0.5
-15
0.6
0.7
Freq [GHz]
0.8
0.9
1
-5
-1.5
0.5
1
0
-10
0.4
0.9
5
-1
-2
0.8
Phase balance(degree)
2
Phase balance(degree) 23
Amplitude Balance23 (dB)
Amplitude Balance (dB)
0.6
0.7
Freq [GHz]
0.8
0.9
1
0.8
0.9
1
-20
0.4
0.5
0.6
0.7
Freq [GHz]
Isolation (dB)
0
-5
Isolation 23(dB)
-10
-15
-20
-25
-30
-35
0.4
0.5
0.6
0.7
Freq [GHz]
Visit us at
www.anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model PD0409J5050S2HF
Rev A
Mounting Configuration:
In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be
used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet
published specifications.
All of the Xinger components are constructed from organic PTFE based composites which possess excellent
electrical and mechanical stability. Xinger components are compliant to a variety of ROHS and Green standards and
ready for Pb-free soldering processes. Pads are Gold plated with a Nickel barrier.
An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the
transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying
pick and place equipment tolerances. In addition, since the PD0409J5050S2HF is a Wilkinson power divider, an
external 0603 100Ω resistor must be mounted in locations R1 as shown in the Figure below.
Pad Footprint w/ 0603 Resistor Locations
Circuit Pattern
Dimensions are in Millimeters
Mounting Footprint
Footprint Pad (s)
3x Transmission
lines
Solder Resist
3x Plated thru
holes to ground
6x .33
.04
6x .41
4x .25
.66
R1
Visit us at
www.anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Model PD0409J5050S2HF
Rev A
Packaging and Ordering Information
Parts are available in reels and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order
quantities are 4000 per reel. See Model Numbers below for further ordering information.
2.00
.81
4.00
1.75
3.50
8.00
1.60
4.00
2.41
.25
Visit us at
www.anaren.com
USA/Canada:
Toll Free:
Europe:
Asia:
(315) 432-8909
(800) 411-6596
+44 2392-232392
+86 512-62749282
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Anaren:
PD0409J5050S2HF
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement