Click Here to this file: /lbwa1zv1cd

Click Here to this file: /lbwa1zv1cd
Preliminary Specification Number : SP-ZV1CD-F
WiFi Module Data Sheet
Broadcom BCM43362 WiFi + ST Micro STM32F405 MCU
Tentative P/N : LBWA1ZV1CD-716
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-ZV1CD-F
1 / 24
The revision history of the product specification
Issued
Date
Revision
Code
Apr.11.2014
May.23.2014
A
Jun.3.2014
B
Revision
Page
P4
P10
P17
P9
P11
Jul.1.2014
C
P12
P18
P10
Jul.31.2014
D
Oct.14.2014
E
P18
Jun.8.2015
F
P18
P18
Changed Items
First issued
3. Block Diagram, 2MBit -> 4MBi
7. Absolute Maximum Rating
8. Operating Condition
9. Electric characteristics
14. Recommended Components
5. LED Drive
6. Phototransistor
Corrected reference paragraph
10. External clock source
characteristics add
11. Power Up Sequence
Changed "NRST" to "RESET_L"
15.4. Low Power Schematic
-ABS07-120-32.768kHz-T add
-Changed "ST3215SB32768B0HPWB1"
to "ST3215SB32768B0HPWB3"
7. SPI Flash Requirements
Added SPI Flash Requirements
16. Recommended Components
Added SPI Flash
16. Recommended Components
-Changed APT2012P3BT with KDT00030TR
-Changed S24FLxxx with S25FLxxx
16.5. Low Power Schematic
-Changed "AP2281" to " AP2281-1/AP2281-3"
-Changed "ABS25-32.768KHZ-T"
to "ABS25-32.768KHZ-6-T "
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Change
Reason
Preliminary Specification Number : SP-ZV1CD-F
2 / 24
TABLE OF CONTENTS
1. Scope ..................................................................................................................................................... 3
2. Part Number ........................................................................................................................................... 3
3. Block Diagram ........................................................................................................................................ 4
4. Dimensions, Marking and Terminal Configurations ............................................................................... 5
4.1. Dimensions ...................................................................................................................................... 5
4.2. Terminal Configurations ................................................................................................................... 6
4.3. Pin Mux Table .................................................................................................................................. 8
5. LED Drive ............................................................................................................................................... 9
6. Phototransistor ....................................................................................................................................... 9
7. SPI Flash Requirements ...................................................................................................................... 10
8. Absolute Maximum Rating ................................................................................................................... 10
9. Operating Condition ............................................................................................................................. 10
10. Electric characteristics.........................................................................................................................11
11. External clock source characteristics ..................................................................................................11
11.1. Low-speed external user clock characteristics .............................................................................11
12. Power Up Sequence .......................................................................................................................... 12
12.1. Without RESET_L control............................................................................................................ 12
12.2. With RESET_L control ................................................................................................................. 12
12.2.1. RESET_L Circuit ................................................................................................................... 12
13. RF Characteristics .............................................................................................................................. 13
13.1. RF Characteristics for IEEE802.11b (11Mbps mode unless otherwise specified.) ..................... 13
13.2. RF Characteristics for IEEE802.11g (54Mbps mode unless otherwise specified.)..................... 13
13.3. RF Characteristics for IEEE802.11n (65Mbps(MCS7) mode unless otherwise specified.) ........ 14
14. Land Pattern (Top View) ..................................................................................................................... 15
15. Reference Circuit................................................................................................................................ 16
15.1. Low Cost Schematic .................................................................................................................... 16
15.2. Low Power Schematic ................................................................................................................. 17
16. Recommended Components ............................................................................................................. 18
16.1. Bi-color LED................................................................................................................................. 18
16.2. Phototransistor............................................................................................................................. 18
16.3. SPI Flash ..................................................................................................................................... 18
16.4. Low Cost Schematic .................................................................................................................... 18
16.5. Low Power Schematic ................................................................................................................. 18
17. Tape and Reel Packing ...................................................................................................................... 19
18. NOTICE .............................................................................................................................................. 22
18.1. Storage Conditions: ..................................................................................................................... 22
18.2. Handling Conditions: ................................................................................................................... 22
18.3. Standard PCB Design (Land Pattern and Dimensions): ............................................................. 22
18.4. Notice for Chip Placer:................................................................................................................. 22
18.5. Soldering Conditions: .................................................................................................................. 23
18.6. Cleaning:...................................................................................................................................... 23
18.7. Operational Environment Conditions: ......................................................................................... 23
18.8. Input Power Capacity: ................................................................................................................. 23
19. PRECONDITION TO USE OUR PRODUCTS ................................................................................... 24
Please be aware that an important notice concerning availability, standard warranty and use in critical
applications of Murata products and disclaimers thereto appears at the end of this specification sheet.
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-ZV1CD-F
3 / 24
1. Scope
This specification is for the LBWA1ZV1CD smart module that provides connectivity to the internet via
WiFi with embedded OS that works with the Electric Imp cloud service.
•
802.11 b/g/n WiFi
- 20MHz 11n channels, 1 x 1
•
32-bit Cortex M4 processor
- Robust embedded operating system with fail-safe firmware updates
- Virtual machine for vendor firmware
•
LED drive for red/green status LEDs
•
Phototransistor input for Electric imp’s patent-pending BlinkUpTM technology to provide
optical configuration
•
23 user selectable I/Os
- GPIO, PWM, Analog input & output, SPI, UART, I2C
- Dedicated SPI bus for local storage
•
Low power 4uA sleep mode (with external load switch)
- Option for coin cell RTC battery backup
•
Compliant with the RoHS directive
2. Part Number
Sample Part Number
LBWA1ZV1CD-716
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-ZV1CD-F
4 / 24
3. Block Diagram
antenna
3.3V switch power supply
4Mbit or higher density
SPI Flash
Load switch
SPDT
opto
LPF
BCM43362
STM32F405
23
I/Os
26MHz
xtal
26MHz
xtal
LBWA1ZV1CD-716
32.768KHz
xtal
DC/DC
inductor
<Low Power Block Diagram>
antenna
4Mbit SPI
Flash
3.3V LDO
SPDT
opto
LPF
BCM43362
STM32F405
23
I/Os
26MHz
xtal
26MHz
xtal
LBWA1ZV1CD-716
DC/DC
inductor
<Low Cost Block Diagram>
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-ZV1CD-F
5 / 24
4. Dimensions, Marking and Terminal Configurations
4.1. Dimensions
< Top View >
< Bottom View >
< Side View >
L
e7
T
23
24
a5 e8
25
26
27
28
29
30
31
32
33
34
55
56
57
58
59
60
61
62
63
64
35
22
37
20
39
19
18
71
72
73
74
75
76
70
69
68
67
66
65
40
41
m2
17
m1
16
e6
a4
e5
c2
54
53
52
51
50
49
48
47
46
42
43
45
44
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
b2
c1
Mark
L
a1
a4
b2
c3
e1
e4
e7
e10
Dimensions
10.0 +/- 0.2
0.65 +/- 0.1
0.35 +/- 0.1
0.30 +/- 0.2
0.80 +/- 0.1
0.30 +/- 0.1
0.80 +/- 0.1
0.75 +/- 0.1
0.60 +/- 0.1
Mark
W
a2
a5
c1
c4
e2
e5
e8
m1
Dimensions
7.9 +/- 0.2
0.35 +/- 0.1
0.80 +/- 0.1
0.80 +/- 0.1
0.80 +/- 0.1
0.30 +/- 0.1
0.40 +/- 0.1
0.30 +/- 0.1
0.40 +/- 0.1
c3
e9
c4
38
21
W
36
e4 a3 e3
e2 a2 e1 a1 b1
Mark
T
a3
b1
c2
c5
e3
e6
e9
m2
Dimensions
1.25 max.
0.35 +/- 0.1
0.30 +/- 0.2
0.80 +/- 0.1
0.80 +/- 0.1
0.30 +/- 0.1
0.30 +/- 0.1
0.50 +/- 0.1
0.40 +/- 0.1
(unit : mm)
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
e10
c5
Preliminary Specification Number : SP-ZV1CD-F
6 / 24
4.2. Terminal Configurations
No.
Terminal Name
Type
1
GND
-
Ground
2
OPTO_Bias
O
Phototransistor bias voltage
3
OPTO_IN
I
Phototransistor input
4
PinW
5
OSC32_IN
I
MCU sleep clock input
6
OSC32_OUT
O
MCU sleep clock output
7
PinN
I/O
I/O, please refer to Pin mux table
8
PSU_EN
O
External power supply enable
9
WLAN_POWER_EN
O
External power gate enable
10
GND
-
Ground
11
GND
-
Ground
12
ANT
-
Antenna
13
GND
-
Ground
14
GND
-
Ground
15
VDD
PI
Power supply for MCU VDD and WLAN Digital IO
16
WLAN_ANT_CTL2
O
Antenna switch control. Default is low.
NC if not in use.
17
WLAN_ANT_CTL1
O
Antenna switch control. Default is high.
NC if not in use.
18
VDD_PA
PI
19
VDD_PA
PI
20
VDD_WLAN
PI
21
VDD_WLAN
PI
22
VDD_DCDC_IN
PI
23
GND
24
VDD_DCDC_OUT
25
SPIFLASH_NCS
O
SPI flash nCS
26
SPIFLASH_MISO
I
SPI flash MISO
I/O
Description
I/O, please refer to Pin mux table
Power supply for Internal Power Amplifier.
Power supply for WLAN IC
PO
Voltage input for core LDO, low noise LDO1 and VCO/LDO
Ground
Voltage output for core LDO.
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-ZV1CD-F
7 / 24
27
SPIFLASH_MOSI
O
SPI flash MOSI
28
SPIFLASH_SCK
O
SPI flash CLK
29
LED_RED
O
Must be connected to the Red terminal of the indicator LED
30
LED_GREEN
O
Must be connected to the Green terminal of the indicator LED
31
PinM
I/O
I/O, please refer to Pin mux table
32
PinL
I/O
I/O, please refer to Pin mux table
33
PinK
I/O
I/O, please refer to Pin mux table
34
PinJ
I/O
I/O, please refer to Pin mux table
35
PinH
I/O
I/O, please refer to Pin mux table
36
GND
-
37
PinG
I/O
I/O, please refer to Pin mux table
38
PinF
I/O
I/O, please refer to Pin mux table
39
PinE
I/O
I/O, please refer to Pin mux table
40
PinD
I/O
I/O, please refer to Pin mux table
41
PinC
I/O
I/O, please refer to Pin mux table
42
PinB
I/O
I/O, please refer to Pin mux table
43
PinA
I/O
I/O, please refer to Pin mux table
44
VDDA
PI
MCU analog power and reference, must be connected to VDD
45
VBAT
PI
MCU retention RAM and RTC backup supply
46
PinY
I/O
I/O, please refer to Pin mux table
47
GND
-
48
PinV
I/O
49
GND
-
Ground
50
DNC
-
Do not connect
51
GND
-
Ground
52
RESET_L
I
MCU reset, internally pulled up
53
GND
-
Ground
54
GND
-
Ground
Ground
Ground
I/O, please refer to Pin mux table
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-ZV1CD-F
8 / 24
55
GND
-
Ground
56
GND
-
Ground
57
GND
-
Ground
58
PinQ
I/O
I/O, please refer to Pin mux table
59
PinR
I/O
I/O, please refer to Pin mux table
60
PinT
I/O
I/O, please refer to Pin mux table
61
PinP
I/O
I/O, please refer to Pin mux table
62
PinS
I/O
I/O, please refer to Pin mux table
63
PinU
I/O
I/O, please refer to Pin mux table
64
PinX
I/O
I/O, please refer to Pin mux table
65
VSSA
-
MCU analog ground, must be connected to GND
66-76
GND
-
Ground
4.3. Pin Mux Table
Pin
Pin A
Pin B
Pin C
Pin D
Pin E
Pin F
Pin G
Pin H
Pin J
Pin K
Pin L
Pin M
Pin N
Pin P
Pin Q
Pin R
Pin S
Pin T
Pin U
Pin V
Pin W
Pin X
Pin Y
uartFG uartQRPW
uartUVGD
uartWJ uartDM i2cFG i2cAB
SCL
SDA
CTS
spiEBCA
spiLGDK ADC DAC PWM
nSS
MISO
SCLK
TX
yes
yes
yes
SCL
SDA
RTS
yes
yes
yes
yes
SCLK
MOSI
TX
RX
Wake from
sleep
yes
yes
yes
yes
MISO
RX
nSS
MOSI
State
change
callback
yes
yes
yes
yes
yes
yes
yes
yes
yes
yes
RTS
TX
RX
yes
yes
yes
TX
RX
TX
for C
for K,X
yes
yes
yes
yes
RX
CTS
Pin trig
pulse gen
yes
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
yes
yes
yes
yes
yes
yes
for G
for D
Preliminary Specification Number : SP-ZV1CD-F
9 / 24
5. LED Drive
The indicator LED should be bicolor, because red, green and amber (red+green) are used to indicate status.
The LED drive pins will auto-detect common anode or common cathode parts. The detection is done by
looking to see which way up the LED_RED pin is idling at boot; to ensure this works correctly, please place a
100k resistor in parallel with the red LED.
The current drive on these pins is 20mA maximum.
Please refer to paragraph 15 for the recommended LEDs.
<Common anode diagram>
<Common cathode diagram>
6. Phototransistor
The phototransistor is used to receive BlinkUp configuration data. The bias resistor connected between
OPTO_IN and GND may need to be adjusted to ensure adequate sensitivity and response time - in general
you need at least 500mV swing on the OPTO_IN pin between black and white states, with the worst
(dimmest) BlinkUp sender you can find.
End-user BlinkUp send data at between 30 and 60 bits per second, depending on the user’s device. For
factory configuration, data is typically sent at 142 bits per second using red LED(s) in a test fixture. If your
application does not require optical configuration, config can be sent electrically at 120 bits per second from
another micro using the OPTO_IN pin. Please contact us for more details.
Please refer to paragraph 15 for the recommended phototransistors.
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-ZV1CD-F
10 / 24
7. SPI Flash Requirements
An external SPI Flash part is required. The minimum size of the SPI Flash is 4 Mbit (512 kByte). The area
below address 0x70000 (448 kByte) is reserved for use by the OS. The remainder of the available space is
made available to user code programmatically. Areas below address 0x70000 will be erased and
reprogrammed by the OS; applications using pre-programmed SPI Flash components must not use space
below this address.
Minimum Size
Reserved for OS (do not pre-program)
4 Mbit (512 kByte)
0x000000 to 0x70000 (448 kByte)
8. Absolute Maximum Rating
Storage Temperature
Supply Voltage
VDD
VDD_PA
VDD_WLAN
min.
max.
unit
-40
+85
-0.3
-0.3
-0.3
4
6
6
deg.C
V
V
V
Caution! The absolute maximum ratings indicate levels where permanent damage to the device can occur, even if
these limits are exceeded for only a brief duration. Functional operation is not guaranteed under these conditions.
Opertation at absolute maximum conditions for extended periods can adversely affect long-term reliabilty of the
device.
9. Operating Condition
Operating Temperature Range(*1)
Specification Temperature Range
VDD
Supply Voltage
VDD_PA
VDD_WLAN
Backup operating Voltage
VBAT
min.
-40
-20
1.8
2.3(*2)
2.3(*2)
typ.
3.3
3.3
3.3
max.
+85
+70
3.6
4.8(*2) (*3)
4.8(*2) (*3)
unit
deg.C
deg.C
V
V
V
1.65
3.3
3.6
V
[Note] All RF characteristics in this datasheet are defined by Specification Temperature Range
(*1) Functionality is guaranteed but specifications require derating at extreme temperatures.
(*2)The BCM43362 is functional across this range of voltage. RF performance is guaranteed only 3.0V < VDD_PA/WLAN < 4.8V
(*3) The maximum continuous voltage is 4.8V. Voltages up to 5.5V for up to 10 seconds, cumulative duration, over the lifetime of the
device are allowed voltages as high 5.0V for up to 250 seconds, cumulative duration, over the lifetime of the device are allowed.
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-ZV1CD-F
11 / 24
10. Electric characteristics
Parameter
Description
Typ
Max
Unit
80
250(*1)
mA
IDD
Normal operation, WiFi on
Normal operation, WiFi power-save
mode enabled
WiFi is off, processor sleep, RTC on,
nvram preserved
8
250(*1)
mA
IDDA
Current input on VDDA
70
VIH
I/O input high level voltage
VIL
IOUT
I/O input
leakage
current
Load
capacitance
Min
6
uA
500
uA
0.7Vdd
3.6
V
I/O input low level voltage
Vss-0.3
0.3Vdd
V
Output current on any single I/O pin
-8
8
mA
Output current on LED_RED pin
-20
20
mA
Output current on LED_GREEN pin
-20
20
mA
Total output current on all I/O pins
including LED_RED & LED_GREEN
-80
-80
mA
6
uA
VSS ≦ VIN ≦ VDD
Pins A to Y
15
pF
(*1) 250mA current is during worst-case TX events. These are a maximum of ~4.8ms long (802.11b 1Mbps)
11. External clock source characteristics
11.1. Low-speed external user clock characteristics
Symbol
fLSE_ext
VLSEH
VLSEL
tW(LSE)
tf(LSE)
tr(LSE)
tr(LSE)
Cin(LSE)
Parameter
( 1)
User External clock source frequency *
OSC32_IN input pin high level voltage
OSC32_IN input pin low level voltage
Conditions
( 1)
OSC32_IN high or low time *
Min
0.7VDD
VSS
Typ
32.768
-
Max
1,000
VDD
0.3VDD
Unit
kHz
450
-
-
-
-
50
-
5
-
pF
30
-
6
1.5
70
±1
60
%
uA
kΩ
pF
pF
V
ns
( 1)
OSC32_IN rise or fall time *
( 1)
OSC32_IN input capacitance *
DuCy(LSE) Duty cycle
IL
OSC32_IN Input leakage current
ESR
Equivalent Series Resistance
CL
Load Capacitance
C0
Shunt Capacitance
(*1) Guaranteed by design, not tested in production
VSS ≤ VIN ≤ VDD
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-ZV1CD-F
12 / 24
12. Power Up Sequence
12.1. Without RESET_L control
Ramp time 90% > 40µs
VDD_3P3
Timing same as VDD_3P3
VDD_WLAN
VDD_PA
*Power down sequence is opposite sequence of power up.
12.2. With RESET_L control
Ramp time 90% > 40µs
VDD_3P3
Timing same as VDD_3P3
VDD_WLAN
> 2 Sleep Clock cycles ( > 61 µs )
VDD_PA
RESET_L
*Power down sequence is opposite sequence of power up.
12.2.1. RESET_L Circuit
VDD
External
Reset circuit (1)
(3)
R PU (4)
RESET_L
Internal
Reset
(2)
Filter
0.1uF
Murata
Module
(1)
(2)
(3)
(4)
The reset network protects the device against parasitic resets.
The use must ensure that the level on the RESET_L pin can go below the 0.8V. Otherwise the reset is not taken into account by the
device.
Vdd=3.3V(for the 1.8≦ Vdd≦ 3.6 voltage range)
RPU=40k ohm (for the 30≦ RPU≦ 50kohm range)
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-ZV1CD-F
13 / 24
13. RF Characteristics
13.1. RF Characteristics for IEEE802.11b (11Mbps mode unless otherwise specified.)
Conditions: 25deg.C, VDD=VDD_WLAN=3.3V
Items
Specification
Mode
Frequency
Data rate
Target Max Output Power
- DC Characteristics 1. DC current
1) Tx mode
2) Rx mode
- Tx Characteristics 2. Power Levels
- Rx Characteristics 3. Minimum Input Level Sensitivity
1) 11Mbps (FER < 8%)
4. Maximum Input Level (FER < 8%)
5. Adjacent Channel Rejection
(FER < 8%)
min.
Contents
IEEE802.11b
DSSS / CCK
2400 - 2483.5MHz
1, 2, 5.5, 11Mbps
17.0
Typ.
max.
Unit
min.
15.0
min.
TBD
120
Typ.
17.0
typ.
TBD
170
max.
19.0
max.
mA
mA
Unit
dBm
Unit
-10
-87
-
-76
-
dBm
dBm
35
-
-
dB
13.2. RF Characteristics for IEEE802.11g (54Mbps mode unless otherwise specified.)
Conditions: 25deg.C, VDD=VDD_WLAN=3.3V
Items
Specification
Mode
Frequency
Data rate
Target Max Output Power
- DC Characteristics 1. DC current
1) Tx mode (1024byte, 20usec interval)
2) Rx mode
- Tx Characteristics 2. Power Levels
- Rx Characteristics 3. Minimum Input Level Sensitivity
1) 54Mbps (PER < 10%)
4. Maximum Input Level (PER < 10%)
5. Adjacent Channel Rejection
(PER < 10%)
min.
Contents
IEEE802.11g
OFDM
2400 - 2483.5MHz
6, 9, 12, 18, 24, 36, 48, 54Mbps
13.0dBm
Typ.
max.
Unit
min.
11.0
min.
295
125
typ.
13.0
typ.
370
170
max.
15.0
max.
mA
mA
unit
dBm
Unit
-20
-73
-
-65
-
dBm
dBm
-1
-
-
dB
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-ZV1CD-F
14 / 24
13.3. RF Characteristics for IEEE802.11n (65Mbps(MCS7) mode unless otherwise specified.)
Conditions: 25deg.C, VDD=VDD_WLAN=3.3V
Items
Specification
Mode
Frequency
Data rate
Target Max Output Power
- DC Characteristics 1. DC current
1) Tx mode (1024byte, 20usec interval)
2) Rx mode
- Tx Characteristics 2. Power Levels
- Rx Characteristics 3. Minimum Input Level Sensitivity
1) 65Mbps (PER < 10%)
4. Maximum Input Level (PER < 10%)
5. Adjacent Channel Rejection
(PER < 10%)
Contents
IEEE802.11n
OFDM
2400 - 2483.5MHz
6.5, 13, 19.5, 26, 39, 52, 58.5, 65Mbps
12.0dBm
min.
Typ.
max.
Unit
min.
10.0
min.
280
125
typ.
12.0
typ.
350
170
max.
14.0
max.
mA
mA
Unit
dBm
Unit
-20
-70
-
-64
-
dBm
dBm
-2
-
-
dB
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-ZV1CD-F
15 / 24
14. Land Pattern (Top View)
5.00
4.70
4.05
3.75
3.40
3.10
2.75
2.45
2.10
1.80
1.45
1.15
0.80
0.50
0.15
0.95
1.55
2.35
3.95
3.95
3.65
2.85
2.45
2.10
1.80
1.45
1.15
0.80
0.50
0.15
0.15
0.15 0.50
0.95 0.80
1.25
1.15
1.45
2.05
2.35
1.80
2.10
3.15
2.45
5.00
2.75
3.10
3.90
4.70
5.00
Unit : mm
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-ZV1CD-F
16 / 24
15. Reference Circuit
15.1. Low Cost Schematic
Please refer to paragraph 16 for the low cost recommended components.
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-ZV1CD-F
17 / 24
15.2. Low Power Schematic
Please refer to paragraph 16 for the low power recommended components.
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-ZV1CD-F
18 / 24
16. Recommended Components
16.1. Bi-color LED
Manufacturer
Manufacturer’s part number
SunLED
Liteon
SunLED
Bivar
XZMDKVG59W-1
LTST-C195KGJRKT
XZMDKVG88W
SM1204BC
SunLED
Liteon
XLMDKVG34M
LTL1BEKVJNN
Manufacturer
Manufacturer’s part number
Everlight
Fairchild
SunLED
Everlight
PT17-21C/L41/TR8
KDT00030TR
XZRNI56W-1
PT12-21C/TR8
SunLED
Honeywell
XRNI30W-1
SDP8405-003
Manufacturer
Spansion
Macronix
Spansion
Macronix
Manufacturer’s part number
S25FL204K
MX25L4006E
S25FL132K
MX25L3206E
Surface mount
top-view
side-view
Through-hole
3mm
16.2. Phototransistor
Surface mount
top-view
side-view
Through-hole
3mm
16.3. SPI Flash
Size
4 Mbit
4 Mbit
32 Mbit
32 Mbit
16.4. Low Cost Schematic
Size
U2
Q1
D1
L1
Manufacturer
Manufacturer’s part number
please refer to paragraph 16.3
please refer to paragraph 16.2
please refer to paragraph 16.1
Murata
LQM21PN1R5MC0
Description
SPI Flash
clear lens phototransistor
red/green bicolor LED
1.5uH inductor
16.5. Low Power Schematic
Ref Des
U2
U3
Q1
D1
L1
Y1
Manufacturer
Manufacturer’s part number
please refer to paragraph 16.3
Diodes Inc.
AP2281-1/AP2281-3
please refer to paragraph 16.2
please refer to paragraph 16.1
Murata
LQM21PN1R5MC0
Kyocera
ST3215SB32768B0HPWB3
Abracon
ABS25-32.768KHZ-6-T
Abracon
ABS07-120-32.768kHz-T
Description
SPI Flash
2A load switch
clear lens phototransistor
red/green bicolor LED
1.5uH inductor
32.768kHz crystal
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-ZV1CD-F
19 / 24
17. Tape and Reel Packing
2.0±0.1
4.0±0.1
φ 1.5+0.1/-0.0
0.30±0.05
11.5±0.1
10.5±0.1
24.0±0.3/-0,1
1.75±0.10
(1) Dimensions of Tape (Plastic tape)
φ 2.0±0.1/-0.0
16.0±0.1
8.4±0.1
1.5 max.
(1.4±0.1)
feeding direction
The corner and ridge radiuses (R) of inside cavity are 0.3mm max.
Cumulative tolerance of 10 pitches of the sprocket hole is +/-0.2mm
Measuring of cavity positioning is based on cavity center in accordance with JIS/IES standard.
(2) Dimensions of Reel
25.5±0.6
( φ 330)
2.0±0.5
( φ 100)
1)
2)
3)
φ 13±0.2
30.5 max.
(unit : mm)
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-ZV1CD-F
20 / 24
(3) Taping Diagrams
[1] Feeding Hole : As specified in (1)
[2] Hole for chip : As specified in (1)
[3] Cover tape
: 62μm in thickness
[4] Base tape
: As specified in (1)
[3]
[1]
[2]
[3]
[4]
Feeding Hole
Feeding Direction
Pin 1 Marking
Chip
(4) Leader and Tail tape
Feeding direction
Tail tape
(No components)
40 to 200mm
Components
No components
Leader tape
(Cover tape alone)
150mm min.
250mm min.
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-ZV1CD-F
21 / 24
(5) The tape for chips are wound clockwise, the feeding holes to the right side as the tape is pulled
toward the user.
(6) The cover tape and base tape are not adhered at no components area for 250mm min.
(7) Tear off strength against pulling of cover tape : 5N min.
(8) Packaging unit : 1000pcs./ reel
(9) material : Base tape : Plastic
Real
: Plastic
Cover tape, cavity tape and reel are made the anti-static processing.
(10) Peeling of force : 0.7N max. in the direction of peeling as shown below.
0.7 N max.
165 to 180 °
Cover tape
Base tape
(11) Packaging (Humidity proof Packing)
Label
表示ラべル
Desiccant
乾燥剤
Humidity
湿度
Indicator
インジケ-タ
表示ラベル
Label
防湿梱包袋
Anti-humidity
Plastic Bag
Tape and reel must be sealed with the anti-humidity plastic bag. The bag contains the desiccant
and the humidity indicator.
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-ZV1CD-F
22 / 24
18. NOTICE
18.1. Storage Conditions:
Please use this product within 6month after receipt.
- The product shall be stored without opening the packing under the ambient temperature from 5 to
35deg.C and humidity from 20 to 70%RH.
(Packing materials, in particular, may be deformed at the temperature over 40deg.C.)
- The product left more than 6months after reception, it needs to be confirmed the solderbility before
used.
- The product shall be stored in non corrosive gas (Cl2, NH3, SO2, Nox, etc.).
- Any excess mechanical shock including, but not limited to, sticking the packing materials by sharp
object and dropping the product, shall not be applied in order not to damage the packing materials.
This product is applicable to MSL3 (Based on JEDEC Standard J-STD-020)
- After the packing opened, the product shall be stored at <30deg.C / <60%RH and the product shall be
used within 168hours.
- When the color of the indicator in the packing changed, the product shall be baked before soldering.
Baking condition: 125+5/-0deg.C, 24hours, 1time
The products shall be baked on the heat-resistant tray because the material (Base Tape, Reel Tape and
Cover Tape) are not heat-resistant.
18.2. Handling Conditions:
Be careful in handling or transporting products because excessive stress or mechanical shock may
break products.
Handle with care if products may have cracks or damages on their terminals, the characteristics of
products may change. Do not touch products with bear hands that may result in poor solder ability and
destroy by static electrical charge.
18.3. Standard PCB Design (Land Pattern and Dimensions):
All the ground terminals should be connected to the ground patterns. Furthermore, the ground pattern
should be provided between IN and OUT terminals. Please refer to the specifications for the standard
land dimensions.
The recommended land pattern and dimensions is as Murata's standard. The characteristics of products
may vary depending on the pattern drawing method, grounding method, land dimensions, land forming
method of the NC terminals and the PCB material and thickness. Therefore, be sure to verify the
characteristics in the actual set. When using non-standard lands, contact Murata beforehand.
18.4. Notice for Chip Placer:
When placing products on the PCB, products may be stressed and broken by uneven forces from a
worn-out chucking locating claw or a suction nozzle. To prevent products from damages, be sure to
follow the specifications for the maintenance of the chip placer being used. For the positioning of
products on the PCB, be aware that mechanical chucking may damage products.
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-ZV1CD-F
23 / 24
18.5. Soldering Conditions:
The recommendation conditions of soldering are as in the following figure.
When products are immersed in solvent after mounting, pay special attention to maintain the
temperature difference within 100 °C. Soldering must be carried out by the above mentioned
conditions to prevent products from damage. Set up the highest temperature of reflow within 260 °C.
Contact Murata before use if concerning other soldering conditions.
Reflow soldering standard conditions(Example)
Within 3s
240to 250 deg.C
220 deg.C
Cooling down
Slowly
180 deg.C
150 deg.C
Pre-heating
Within 120s
Within 60s
time(s)
Please use the reflow within 2 times.
Use rosin type flux or weakly active flux with a chlorine content of 0.2 wt % or less.
18.6. Cleaning:
Since this Product is Moisture Sensitive, any cleaning is not permitted.
18.7. Operational Environment Conditions:
Products are designed to work for electronic products under normal environmental conditions (ambient
temperature, humidity and pressure). Therefore, products have no problems to be used under the similar
conditions to the above-mentioned. However, if products are used under the following circumstances, it
may damage products and leakage of electricity and abnormal temperature may occur.
- In an atmosphere containing corrosive gas ( Cl2, NH3, SOx, NOx etc.).
- In an atmosphere containing combustible and volatile gases.
- Dusty place.
- Direct sunlight place.
- Water splashing place.
- Humid place where water condenses.
- Freezing place.
If there are possibilities for products to be used under the preceding clause, consult with Murata before
actual use.
As it might be a cause of degradation or destruction to apply static electricity to products, do not apply
static electricity or excessive voltage while assembling and measuring.
18.8. Input Power Capacity:
Products shall be used in the input power capacity as specified in this specifications.
Inform Murata beforehand, in case that the components are used beyond such input power capacity
range.
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Preliminary Specification Number : SP-ZV1CD-F
24 / 24
19. PRECONDITION TO USE OUR PRODUCTS
PLEASE READ THIS NOTICE BEFORE USING OUR PRODUCTS.
Please make sure that your product has been evaluated and confirmed from the aspect of the fitness for the specifications
of our product when our product is mounted to your product.
All the items and parameters in this product specification/datasheet/catalog have been prescribed on the premise that our
product is used for the purpose, under the condition and in the environment specified in this specification. You are
requested not to use our product deviating from the condition and the environment specified in this specification.
Please note that the only warranty that we provide regarding the products is its conformance to the specifications provided
herein. Accordingly, we shall not be responsible for any defects in products or equipment incorporating such products,
which are caused under the conditions other than those specified in this specification.
WE HEREBY DISCLAIMS ALL OTHER WARRANTIES REGARDING THE PRODUCTS, EXPRESS OR IMPLIED,
INCLUDING WITHOUT LIMITATION ANY WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, THAT THEY ARE
DEFECT-FREE, OR AGAINST INFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS.
The product shall not be used in any application listed below which requires especially high reliability for the prevention of
such defect as may directly cause damage to the third party's life, body or property. You acknowledge and agree that, if
you use our products in such applications, we will not be responsible for any failure to meet such requirements.
Furthermore, YOU AGREE TO INDEMNIFY AND DEFEND US AND OUR AFFILIATES AGAINST ALL CLAIMS,
DAMAGES, COSTS, AND EXPENSES THAT MAY BE INCURRED, INCLUDING WITHOUT LIMITATION, ATTORNEY
FEES AND COSTS, DUE TO THE USE OF OUR PRODUCTS IN SUCH APPLICATIONS.
- Aircraft equipment.
- Aerospace equipment
- Undersea equipment.
- Power plant control equipment - Medical equipment.
- Transportation equipment (vehicles, trains, ships, elevator, etc.).
- Traffic signal equipment.
- Disaster prevention / crime prevention equipment.
-Burning / explosion control equipment
- Application of similar complexity and/ or reliability requirements to the applications listed in the above.
We expressly prohibit you from analyzing, breaking, reverse-engineering, remodeling altering, and reproducing our
product. Our product cannot be used for the product which is prohibited from being manufactured, used, and sold by the
regulations and laws in the world.
We do not warrant or represent that any license, either express or implied, is granted under any our patent right, copyright,
mask work right, or our other intellectual property right relating to any combination, machine, or process in which our
products or services are used. Information provided by us regarding third-party products or services does not constitute a
license from us to use such products or services or a warranty or endorsement thereof. Use of such information may
require a license from a third party under the patents or other intellectual property of the third party, or a license from us
under our patents or other intellectual property.
Please do not use our products, our technical information and other data provided by us for the purpose of developing of
mass-destruction weapons and the purpose of military use.
Moreover, you must comply with "foreign exchange and foreign trade law", the "U.S. export administration regulations",
etc.
Please note that we may discontinue the manufacture of our products, due to reasons such as end of supply of materials
and/or components from our suppliers.
By signing on specification sheet or approval sheet, you acknowledge that you are the legal representative for your
company and that you understand and accept the validity of the contents herein. When you are not able to return the
signed version of specification sheet or approval sheet within 30 days from receiving date of specification sheet or
approval sheet, it shall be deemed to be your consent on the content of specification sheet or approval sheet. Customer
acknowledges that engineering samples may deviate from specifications and may contain defects due to their
development status. We reject any liability or product warranty for engineering samples. In particular we disclaim liability
for damages caused by
- the use of the engineering sample other than for evaluation purposes, particularly the installation or integration in the
product to be sold by you,
-deviation or lapse in function of engineering sample,
-improper use of engineering samples.
We disclaim any liability for consequential and incidental damages.
If you can’t agree the above contents, you should inquire our sales.
< Specification may be changed by Murata without notice >
Murata Manufacturing Co., Ltd.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement