Mytee | M-16 | User manual | Mytee M-16 User manual

Mytee M-16 User manual
Instructions for
M-3, M-5, M-12 & M-16 M-Series™
Please read before use.
Register your product
at www.mytee.com/help
Model #
M-3 p. 2
M-5 p. 8
M-12 p.14
M-16 p. 21
General information p. 27
Serial #
Form # ADM-MSeries
1-12
13655 Stowe Dr., Poway, Ca. 92064
1
M-3 M-SERIES™
M-3 FRONT
M-3 BACK
11
1
2
10
20
12
3
9
19
13
4
14
15
5
8
1. Switch plate
2. 2” Male Cuff-Lynx™
3. Female quick disconnect (QD)
4. Front handles
5. Prime valve
7
16
6
17
6. Pressure regulator
7. Front cooling fan
8. 4” locking casters
9. Solution tank
10. Solution tank cover
11. Recovery tank lid
12. Push handle
13. Drain valve
14. Auto-fill
15. Auto pump-out
M-3 ITEMS INCLUDED
18
16. Rear cooling fan
17. Dual power cords
18. 12” rear wheels
19. Latches (x2)
20. Recovery tank
M-3 DUAL CORDS
Top cord: Plug into power Vac 1, Pump & Heater 1.
Bottom cord: Plug into power Vac 2, Pump-out & Heater 2.
H110 Cuff-Lynx™
2” Hose Adapter
H141 Cuff-Lynx™
2” Hose Reducer to 1.5”
Top cord
Bottom cord
H375 Hose Hanger
(4) screws
H226 Drain Elbow
Plug each of the two power cords into two separate, 20A grounded
wall outlets. The amber light indicator on the switch plate will illuminate when cords are plugged into two separate circuits.
2
M-3 M-SERIES™
M-3 VAC/SOL HOSE CONNECTIONS
M-3 SWITCHES & PRESSURE GAUGE
1
VAC
UMP
P
2
VAC
TER
HEA
Switches and Pressure Gauge are located on the plate in front
of the machine. The Amber light left of the Pressure Gauge will
illuminate when cords are plugged into two separate circuits. To use
vacuums, turn on Vac 1 and Vac 2 switches. To use Pump, turn on
Pump switch. Heater switch has three positions: Off (middle); 1,000
watts using one heater (left); and 2,000 using two heaters (right).
Red lights on panel display indicate watts selected: one light =
1,000 watts; two lights = 2,000 watts; no lights = heater is off.
Before turning on switches, connect hoses to the extractor and a
wand or tool. Attach a solution hose to the front QD, the other end
to the tool. Attach a vacuum hose to the tool, the other to the front
Cuff-Lynx™ vacuum hose port. Just twist into place.
M-3 AUTO-FILL & PUMP-OUT
M-3 FILL SOLUTION TANK
AUTO-FILL
PUMP-OUT
-OUT
PUMP
If using Auto-fill and Pump-out, connect one end of a 1/2 inch
garden hose to the top hose inlet in back of the machine, the other
end to a faucet. Add water pressure by turning on faucet. Attach a
second 1/2 inch garden hose to the bottom hose inlet, and place the
other end in a location where dirty water can drain. Turn on Pumpout switch. When job is complete, turn off Pump-out switch.
If not using the Auto-fill feature, lift the solution tank lid and manually fill
the tank.
3
M-3 M-SERIES™
M-3 AUTO-FILL & FLOAT
M-3 PRIME VALVE & PRESSURE REGULATOR
PRIME VALVE
1003/1005
HIGHER PSI
PRESSURE
REGULATOR
LOWER PSI
After attaching a garden hose to the Auto-fill inlet, water will fill the
tank to a predetermined level until stopped by the float. As water is
used and the level drops, water will once again enter the tank, and
be stopped again by the float when maximum level is reached.
With each new job, check to make sure float stops water after the
first fill.
Prime the pump by turning the valve to the Prime position for 30
seconds, then turn horizontally to the Run position. Turn the
Pressure Regulator to the left to decrease the water pressure.
Turn the pressure regulator to the right to increase the water
pressure. Monitor pressure while adjusting, using Pressure Gauge
on Switch Panel.
M-3 DRAIN VALVE & LATCHES
M-3 FILTER MAINTENANCE
PUMP-OUT
FILTER
PRIME VALVE
FILTER
CLEAN WATER
INTAKE FILTER
You can drain the recovery tank by using the Drain Valve. When
not using the Auto Pump-out, you can drain the recovery tank by
using the Drain Valve. When the tank is full, an internal ball float
will automatically shut off the vacuum. Attach the 45˚ drain elbow
to the drain spout, and lift up the Drain Valve to empty the tank.
Latches are located in the back to open tank for internal repairs.
To clean the internal filters, lift solution lid and/or remove recovery tank
lid, reach in and twist off. Rinse with clean water and replace.
4
Order parts at: http://www.mytee.com/products/product.php?id=M-3
5
A
B
C
D
E
F
B130
H212
B106
17
18
19
8
H202
66
E519
H210
65
H903A
H216
64
70
H601
63
69
washer, zinc, 1.625 x .847 x .078
P750
H191
G004
61
62
AH202
H217
60
67
H501
59
68
bolt, 1/4x20x3/4" hex head
C302
58
heating rod, 1000W, 115V
heater, aluminum cast, single
hose, pulse, 3/8" x 34", (OAL)
washer, 1/4" flat, s/s
nut, lock, 1/4-20, nylon insert, s/s
plate, manifold, parallel
manifold, dual vac, parallel
gasket, vacuum motor
clamp, hose, 2-1/4 dia
vac support, 3 stage, 4-1/16"
vac motor, 3 stage, 120V, tangential
exhaust boot, plastisol
vac hose, 2", black wire reinforced
cuff hose, 2 X 2, wire reinforced
screw, #10 x 5/8" hex head zinc
H544
H343
54
filter, strainer, 1/2"
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
G059
B186
PH628-25
B119A
52
53
handle, breeze and dx
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
57
H768
51
56
H485
50
sol tank, m series
bushing, brass, 3/8"mpt x 1/4"
nipple, 12" x 1/4" npt, m x m
valve, float, autofill
cover, sol tank (m-series)
55
B105
P708
48
B115
47
49
H541
46
nut, hex, 1/4-20 s/s
H215
G212
44
H213
43
45
washer, 1/4" lock, s/s
G052
42
washer, buna 1-1/8" od x 3/16" id
washer, 1/4"id x 1"od, flat, s/s
H211
qd, brass, 1/4" f
screw, 10-32 x 1/2" phil pan head, s/s
41
H230
38
plate, mounting, QD
sol hose, 57 x 1/4", (OAL), m x msw 3000psi
bolt, 1/4-20 x 1 1/4"
H484
37
B102
AH195
36
adapter, brass, 3/8" female npt x 1/4" male npt
H203
B643
35
gauge, pressure, 2000 PSI
40
H308D
34
Washer, #8, flat regular
screw, #10-32 x 1/2" SHCS, alloy
switch, rocker, 3 position
switch, rocker, 2 position
light, red, 250v
light, indicator, 125v (amber)
plate, switch, sp, 4 hole w/gauge
hose, pulse, 3/8" x 34", (OAL)
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
nipple, brass, 3/8" x close
washer, 11/16"id x 1-1/2"od x .075, s/s
bushing, brass, 1/2"mpt x 3/8" fpt, hex
mesh filter, auto dump, 1/2" npt
adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex
nipple, brass, 1/4" x close
washer, 9/16"id x 1"od, flat, s/s
45 deg, street elbow, brass, 1/4" male NPTF
filter, strainer, 1/4"
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
bracket, "L" (all extracters)
valve, drain, 1-1/2"
vac tank, m series
elbow, inlet assembly 2"
39
E516
H616
E515
30
H389
E511
29
33
E512B
28
32
H337
31
B103
AH203
27
24
26
B216
23
25
B210
H299
22
B111
B119
16
H333
H770
15
21
H390A
14
20
P709
H225
A926
11
13
inlet, 2"
12
adaptor, pvc 2, fmsl x fmt
P685
Cuff-Lynx, 2" m cuff x 2" mpt
P684
H135
9
pipe, pvc, 2"
P682
7
8
float, 2", ball style
10
screw, 8 x 1/2", hex head, zinc
H297
elbow, 2" float
gasket, 7", vac lid
H490
P726
3
4
lid, vac tank, black, 7"
screw, #8 x 5/8 phil oval, s/s
DESCRIPTION
5
G091
2
8
6
H304
G090
1
PART
NO.
ITEM
NO.
7
7
2
2
1
2
10
35
17
1
1
2
3
6
2
2
1
1
10
5
1
13
2
1
4
1
1
1
2
4
6
8
2
1
19
1
1
1
1
3
3
1
4
2
1
1
1
8
2
9
3
1
3
1
6
3
1
4
2
1
1
1
1
1
1
1
1
3
1
1
1
6
QTY.
$51.99 ea
$78.99 ea
$39.99 ea
$0.99 ea
$0.99
$0.99 ea
$0.99
$13.49 ea
$15.99 ea
$8.99 ea
$1.49 ea
$4.99 ea
$139.99 ea
$4.99 ea
$8.99/ft
$12.49 ea
$0.99 ea
$8.99 ea
$6.49 ea
$0.99 ea
$6.99 ea
$210.99 ea
$3.19 ea
$23.99 ea
$124.99 ea
$12.99 ea
$0.99 ea
$0.99
$1.99 ea
$0.99 ea
$0.99
$17.99 ea
$0.99 ea
$4.99 ea
$37.99 ea
$4.99 ea
$38.99 ea
$0.99 ea
$0.99 ea
$14.99 ea
$13.99 ea
$5.99 ea
$9.99 ea
$8.99 ea
$47.99 ea
$4.49 ea
$1.99 ea
$0.99 ea
$2.49 ea
$9.99 ea
$3.49 ea
$3.49 ea
$0.99 ea
$5.49 ea
$3.99 ea
$0.99 ea
$6.99 ea
$20.99 ea
$243.99 ea
$15.99 ea
$3.99 ea
$10.99 ea
$6.99 ea
$7.99/ft
$18.49 ea
$11.49 ea
$11.99 ea
$36.99 ea
$0.99 ea
MSRP
6
AH156
B235
85
B246
B160
90
B644
controller, circuit light
gasket, strip, 3/4" x 36" x 1/8"
hanger, wire formed, hose
spout, drain, 45 degree
E564
G085
H375
H226
DESCRIPTION
filter, bag, vac tank, draw string
PART
NO.
adapter, brass, 1/2" barb x 1/2" mpt
5
1
1
2
1
1
QTY.
screw, 10-32 x 3/4", phil flat full thread, black oxide
sol hose, 1/2", black, 200 psi 200 degree max
pump out, 115v
sol hose, 1/2" kuri 100psi
G010
6
B132
125
ITEMS NOT SHOWN
H186
124
C381
PH615-17
122
123
PH615-37
B236
121
bolt, 1/4-20 x 1" hex head, s/s
elbow, brass, 90 deg, 1/2" barb x 3/8" fpt
H342
caster, 4", black hub & gray tread
bolt, 1/4-20 x 1/2", hex head, zinc
bolt, 1/4-20 x 1 3/4" hex head, s/s
bracket, front hinge, sp/fb
base, m series
axle, 19.75" x .50"
washer, axle, cut 1/2" id
wheel, 12"
cap, axle, 1/2"
guard, cooling fan, wire
fitting, brass, 3/4" mgh x 1/2" fpt
cap, brass, 3/4", garden hose
swivel, brass, 3/4" fgh x 1/2" fpt
filter, 60 mesh, garden hose
plug, brass, 3/4", garden hose
plate, switch, spotter
screw, #10-32 x 3/4" phil pan head, zinc
nut, kep, #10-32 zinc
latch, front breeze
nut, lock, 1/2" steel
fitting, strain relief, cord
power cord, pigtail, 30", 12/3, black
solution hose, black, low pressure, 1/2"
tee, brass, 3/8" fpt x 3/8" mpt x 3/8" fpt
elbow, brass, 90 deg, 1/2" barb x 3/8"mpt
sol hose, 1/2", kuri 100 psi
elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt
regulator, 450 psi, silver spring
adapter, brass, 1/2" barb x 1/4" mpt
sol hose, 1/2", kuri 100 psi
adapter, brass, 1/2" barb x 3/8" fsw, ball end
pump, 500 psi, 115V
sol hose, 1/4" x 24 1/2", (OAL)
plug, brass, 3/8" mpt, hex
ball valve, 1/4''
nipple, brass, 1/4"m, hex
elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt
hose, 3/8" x 10", (OAL), f x f
sol hose, kuriyama, 3/8"
clamp, hose, 5/16-29/32
adapter, brass, 3/8" barb x 1/4" fsw
bracket, heater mounting, dual
elbow, brass, 90 deg, 1/4" fpt x 1/4" fpt
hose, 3/8" x 6.5", (OAL), f x fsw, 5400 Gray
hose, 3/8" x 14-1/2" (OAL), f
Thermostat, 310°F ± 10°F, Manual, 1/4"
120
H668
H201
H378
5
screw, #6x3/16,phil pan head, self-tapping
Thermostat, 200°, Auto, 1/4"
DESCRIPTION
119
118
117
116
P707
H378
114
H232
H254
115
113
112
H251
H219
111
H296
110
B196
B120
B642
B640
B221
H410
H256
H273
H486
H221
H220
E550
PH615A-10
B242
B172
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
B652
PH615-24
92
C313C
93
91
PH615-21
88
89
C313
AH108S
87
86
B656
B136
B107
82
83
84
AH103
81
PH715-28
H347
80
80
H528
78
77
B207
AH184
76
75
E574
74
73
E573
H274
71
PART
NO.
72
ITEM
NO.
$3.19 ea
$10.99 ea
$4.99 ea
$62.49 ea
$9.99 ea
MSRP
1
4
1
1
1
1
8
2
2
2
1
1
1
3
2
2
2
1
1
1
1
1
1
1
13
2
2
2
2
1
1
2
1
1
1
2
1
2
1
1
3
1
3
1
1
1
24
2
1
1
1
1
2
2
2
QTY.
$9.49 ea
$0.99 ea
$8.99/ft
$187.49 ea
$0.99 ea
$14.49 ea
$0.99
$19.49 ea
$0.99 ea
$0.99
$8.99 ea
$196.99 ea
$9.99 ea
$0.99 ea
$41.99 ea
$0.99 ea
$2.99 ea
$5.99 ea
$1.49 ea
$5.49 ea
$1.99 ea
13.99 ea
$5.99 ea
$0.99 ea
$0.99 ea
$13.99 ea
$1.99 ea
$3.19 ea
$11.49 ea
$5.99/ft
$13.99 ea
$9.49 ea
$8.99/ft
$8.49 ea
$86.99 ea
$2.49 ea
$8.99/ft
$3.49 ea
$588.99 ea
$39.99 ea
$1.99 ea
$13.49 ea
$3.19 ea
$4.99 ea
$30.49 ea
$7.99/ft
$1.99 ea
$7.99 ea
$29.99 ea
$5.99 ea
$23.99 ea
$27.99 ea
$17.99 ea
$0.99 ea
$16.49 ea
MSRP
4
4
3
3
2
2
M. L
THE INFORMATIO
DRAWING IS THE S
MYTEE PRODUCTS
REPRODUCTION I
WITHOUT THE WRI
MYTEE PRODUCTS
PROPRIETARY A
CHECKED
DRAWN
M-3 M-SERIES™ PARTS & PRICING
Part prices are subject to change.
6
A
B
C
D
E
F
94
80
8
48
90
# 53
96
93
to sol tank
through B186
95
8
88
65
65
116
25
84
117
53
18
115
94
53
43
25
18
# 20
78
80
92
91
50
50
41
# 87
7
51
114
90
48
81
83
80
78
69
88
80
71
70
to pump "in"
83
17
73
72
to vac tank
thru B111
?
# 48
to sol tank
thru B105
7
80
82
89
25
74
118
119
65
65
# 25
to sol tank
thru B103
53
77
25
85
6
75
121
120
23
66
98
65
6
122
101
# 24
48
83
65
123
97
67
124
112
113
80
111
112
125
108
105
86
56
55
106
54 109
57
65
87
22
to vac tank
thru B142
99
# 36
To qd
thru AH195
76
25
# 35
to pressure
guage
through B643
68
# 106
to B642
67
101
102
51
30
58
# 22
to AH202
thru B210
50
42
41
49
23
48
51
23
(# 48 )
# 53
to AH202
thru B186
47
20
25
# 108
65
to regulator
thru B105
# 125
to pump out
thru B132
5
103
38
38
51
63
64
100
58
66
101
60
61
59
5
to B196
110
107 104
54
4
46
4
25
18
18
17
# 88
to pump in
thru B160
45
53
23
23
52
23
23
24
3
39
20
44
38
37
41
41
42
# 76
to heaters "OUT"
thru B207
42
43
3
30
36
40
32
31
29
34
# 86
to pump "OUT"
thru AH108s
33
28
27
26
2
# 120
to pump out
thru B236
35
25
2
6
21
23
24
23
22
14
18
18
16
2
20
19
17
3
DATE
5/25/11
NAME
M. LaBarbera
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
1
SCALE: 1:2
DO NOT SCALE
DRAWING
M3
13
REV
OD
SHEET 2 OF 2
M Series
SIZE DWG. NO.
D
858-679-1191
12
11
mytee PRODUCTS, INC.
TITLE:
# 78
to prive valve
thru B235
10
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
15
9
8
7
5
4
1
1
A
B
C
D
E
F
M-3 M-SERIES™ PARTS & PRICING
7
M3 Wiring
Bottom Cord
Top Cord
PUMP
OUT
M3
Amber
M-3 M-SERIES™ WIRING DIAGRAM
M-5 M-SERIES™
M-5 FRONT
M-5 BACK
11
1
2
10
20
12
3
9
19
13
4
14
15
5
8
1. Switch plate
2. 2” Male Cuff-Lynx™
3. Female quick disconnect (QD)
4. Front handles
5. Prime valve
7
16
6
17
6. Pressure regulator
7. Front cooling fan
8. 4” locking casters
9. Solution tank
10. Solution tank cover
11. Recovery tank lid
12. Push handle
13. Drain valve
14. Auto-fill
15. Auto pump-out
M-5 ITEMS INCLUDED
18
16. Rear cooling fan
17. Dual power cords
18. 12” rear wheels
19. Latches (x2)
20. Recovery tank
M-5 DUAL CORDS
Top cord: Plug into power Vac 1 & Pump.
Bottom cord: Plug into power Vac 2 & Pump-out.
H110 Cuff-Lynx™
2” Hose Adapter
Top cord
H141 Cuff-Lynx™
2” Hose Reducer to 1.5”
Bottom cord
H375 Hose Hanger
(4) screws
H226 Drain Elbow
Plug each of the two power cords into two separate, 20A grounded
wall outlets. The amber light indicator on the switch plate will illuminate when cords are plugged into two separate circuits.
8
M-5 M-SERIES™
M-5 VAC/SOL HOSE CONNECTIONS
M-5 SWITCHES & PRESSURE GAUGE
1
VAC
UT
MP O
2
VAC
P
PUM
PU
Before turning on switches, connect hoses to the extractor and a
wand or tool. Attach a solution hose to the front QD, the other end
to the tool. Attach a vacuum hose to the tool, the other to the front
Cuff-Lynx™ vacuum hose port. Just twist into place.
Switches and Pressure Gauge are located on the plate in front of
the machine. The Amber light left of the Pressure Gauge will illuminate when cords are plugged into two separate circuits. To use
vacuums, turn on Vac 1 and Vac 2 switches. To use Pump, turn on
Pump switch. The Pressure Gauge displays the water pressure as
PSI. To use Pump-out feature, turn on Pump-out switch.
M-5 FILL SOLUTION TANK
M-5 AUTO-FILL & PUMP-OUT
AUTO-FILL
PUMP-OUT
If using Auto-fill and Pump-out, connect one end of a 1/2 inch
garden hose to the top hose inlet in back of the machine, the other
end to a faucet. Add water pressure by turning on faucet. Attach a
second 1/2 inch garden hose to the bottom hose inlet, and place
the other end in a location where dirty water can drain.
If not using the Auto-fill feature, lift the solution tank lid and manually fill
the tank.
9
M-5 M-SERIES™
M-5 AUTO-FILL & FLOAT
M-5 PRIME VALVE & PRESSURE REGULATOR
PRIME VALVE
1003/1005
HIGHER PSI
PRESSURE
REGULATOR
LOWER PSI
After attaching a garden hose to the Auto-fill inlet, water will fill the
tank to a predetermined level until stopped by the float. As water is
used and the level drops, water will once again enter the tank, and
be stopped again by the float when maximum level is reached.
With each new job, check to make sure float stops water after the
first fill.
Prime the pump by turning the valve to the Prime position for 30
seconds, then turn horizontally to the Run position. Turn the
Pressure Regulator to the left to decrease the water pressure.
Turn the pressure regulator to the right to increase the water
pressure. Monitor pressure while adjusting, using Pressure Gauge
on Switch Panel.
M-5 DRAIN VALVE & LATCHES
M-5 FILTER MAINTENANCE
PUMP-OUT
FILTER
PRIME VALVE
FILTER
CLEAN WATER
INTAKE FILTER
You can drain the recovery tank by using the Drain Valve. When
not using the Auto Pump-out, you can drain the recovery tank by
using the Drain Valve. When the tank is full, an internal ball float
will automatically shut off the vacuum. Attach the 45˚ drain elbow
to the drain spout, and lift up the Drain Valve to empty the tank.
Latches are located in the back to open tank for internal repairs.
To clean the internal filters, lift solution lid and/or remove recovery tank
lid, reach in and twist off. Rinse with clean water and replace.
10
Order parts at: http://www.mytee.com/products/product.php?id=M-5
11
A
B
C
D
E
F
H254
H232
15
16
B103
B656
H212
B107
B130
30
31
32
33
DESCRIPTION
C313
AH108S
H202
P735
63
64
65
H544
G059
C302A
68
69
70
H217
AH195
PH628-25
PH615-15
60
61
62
67
B242
59
66
B652
B246
57
PH615-10
56
58
B196
B172
54
55
B640
51
B642
B120
50
52
B221
49
53
E550
G131
48
H221
H220
46
47
H486
45
bushing, brass, 1/2"mpt x 3/8" fpt, hex
B210
H230
43
AH202
42
44
hose, pulse, 3/8" x 34", (OAL)
B186
41
8
motor, 3-stage, 115 cfm,14.5 amps
exhaust boot, plastisol
cuff hose, 2 X 2, wire reinforced
vac hose, 2", black wire reinforced
clamp, hose, 2-1/4 dia
manifold, single vac, no gasket
bolt, 1/4-20 x 3/4" hex head, s/s
sol hose, 1/4" x 24 1/2", (OAL)
pump, 500 psi, 115V
sol hose, 57 x 1/4", (OAL), m
sol hose, 1/2", kuri 100 psi
tee, brass, 3/8" fpt x 3/8" mpt x 3/8" fpt
plug, brass, 3/8" mpt, hex
elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt
sol hose, 1/2", kuri 100 psi
elbow, brass, 90 deg, 1/2" barb x 3/8"mpt
fitting, brass, 3/4" mgh x 1/2" fpt
swivel, brass, 3/4" fgh x 1/2" fpt
filter, 60 mesh, garden hose
cap, brass, 3/4", garden hose
plug, brass, 3/4", garden hose
connector, cord lock
power cord, pigtail, 30", 12/3, black
fitting, strain relief, cord
nut, lock, 1/2" steel
latch, front breeze
screw, 10-32 x 1/2 phil pan
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
guard, cooling fan, wire
screw, 10 x 5/8" hex head, zinc
H343
H296
39
nipple, brass, 1/4" x close
adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex
sol hose, kuriyama, 3/8"
hose, 3/8" x 10", (OAL), f x f
adapter, brass, 3/8" barb x 1/4" fsw
45 deg, street elbow, brass, 1/4" male NPTF
nipple, brass, 1/4"m, hex
washer, 9/16"id x 1"od, flat, s/s
ball valve, 1/4''
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
regulator, 450 psi
elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt
sol hose, 1/2", kuri 100 psi
adapter, brass, 1/2" barb x 3/8" fsw, ball end
bushing, brass, 3/8"mpt x 1/4"
handle, breeze and dx
washer, 1/4"id x 1"od, flat, s/s
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
nut, lock, 1/4-20 nylon insert
bolt, 1/4-20 x 1" hex head, s/s
caster, 4", black hub & gray tread
base, m series
axle, 19.75" x .50"
washer, axle, cut 1/2" id
wheel, 12"
cap, axle, 1/2"
washer, zinc, 1.625 x .847 x .078
adapter, brass, 1/2" barb x 1/4" mpt
adapter, brass, 1/2" barb x 1/2" mpt
sol hose, 1/2", kuri 100 psi
washer, 11/16"id x 1-1/2"od x .075, s/s
elbow, brass, 90 deg, 1/2" barb x 3/8" fpt
clamp, hose, 5/16-29/32
sol hose, 1/2", kuri 100 psi
pump out, 115v
nut, kep, #10-32 zinc
washer, 1/4" flat, s/s
screw, 10-32 x 3/4", phil flat full thread, black oxide
8
40
B106
C313C
28
29
38
B136
27
B111
PH615-21
26
PH715-28
B160
25
37
B105
36
H485
23
24
B235
H211
22
AH103
H768
21
34
H216
20
35
H668
H342
18
19
P707
H251
14
17
H191
H219
12
13
B132
B644
10
PH615-17
9
11
B236
H299
H347
6
8
PH615-37
5
7
H273
C381
3
4
H186
H210
1
2
PART NO.
ITEM
NO.
2
2
2
1
4
2
10
1
1
1
1
1
3
1
1
2
1
1
1
1
1
2
2
2
2
2
18
3
1
4
3
14
1
3
1
1
2
3
3
6
1
5
1
1
1
2
5
2
8
13
17
8
2
1
1
3
2
2
2
2
1
1
9
1
24
1
1
14
27
4
QTY.
7
7
$148.99 ea
$4.99 ea
$12.49 ea
$ 8.99/ft
$1.49 ea
$14.99 ea
$0.99 ea
$26.49 ea
$588.99 ea
$37.99 ea
$8.99/Ft
$13.99 ea
$1.99 ea
$8.49 ea
$8.99/ft
$9.49 ea
$5.99 ea
$5.49 ea
$1.99 ea
$1.49 ea
13.99 ea
$4.99 ea
$11.49 ea
$3.19 ea
$1.99 ea
$13.99 ea
$0.99 ea
$2.49 ea
$39.99
$8.99 ea
$2.99 ea
$0.99 ea
$3.49 ea
$3.49 ea
$7.99/ft
$30.49 ea
$7.99 ea
$5.49 ea
$3.19 ea
$0.99 ea
$13.49 ea
$4.49 ea
$86.99 ea
$4.99 ea
$8.99/ft
$3.49 ea
$3.19 ea
$6.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$19.49 ea
$196.99 ea
$9.99 ea
$0.99 ea
$41.99 ea
$0.99 ea
$0.99 ea
$2.49 ea
$9.49 ea
$8.99/ft
$0.99 ea
$14.49 ea
$1.99 ea
$8.99/ft
$187.49 ea
$0.99 ea
$0.99 ea
$0.99 ea
MSRP
B216
H422
115
116
bracket, "L" (all extracters)
inlet, 2"
screw, #8-32 x 3/8" SHCS, alloy
controller, circuit light
valve, drain, 1-1/2"
vac tank, m series
elbow, inlet assembly 2"
gasket, 7", vac lid
lid, vac tank, black, 7"
screw, #8 x 5/8 phil oval, s/s
screw, #8 x 1/2", hex head, zinc
elbow, 2" float
float, 2", ball style
pipe, pvc, 2"
adaptor, pvc 2, fmsl x fmt
Cuff-Lynx, 2" m cuff x 2" mpt
bolt, 1/4-20 x 1-3/4" hex head, s/s
bolt, 1/4-20 x 1/2", hex head, zinc
bracket, front hinge, sp/fb
filter, strainer, 1/2"
filter, strainer, 1/4"
qd, brass, 1/4" f
plate, mounting, QD
sol tank, m series
bolt, 1/4-20 x 1-1/4" hex head, s/s
washer, buna 1-1/8" od x 3/16" id
6
manual, m-series
stop sign, register your product
spout, drain, 45 degree
cuff-lynx, 2" hose x 2" fem swivel cuff-lynx
hanger, wire formed, hose
screw. 10-32 x 1/2" phil pan head, s/s
cuff-lynx, 2" to 1.5" reducer
banana bag, mesh bag, yellow
DESCRIPTION
gasket, strip, 3/4" x 36" x 1/8"
filrer, bag, vac tank, drawstring
DESCRIPTION
plug, dome 3/8", black
nipple, brass, 3/8" x close
plate, switch, sp, 4 hole w/gauge
light, indicator, 125v (amber)
washer, #8 flat, s/s
screw, #10-32 x 1/2" SHCS, alloy
switch, rocker, 2 position
gauge, pressure, 2000 PSI
hose, pulse, 3/8" x 34", (OAL)
adapter, brass, 3/8" female npt x 1/4" male npt
mesh filter, auto dump, 1/2" npt
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
ADM-M-SERIES
AD127
H226
H110
H375
H230
H141
G029
PART NO.
ACCESSORIES
G085
G010
PART NO.
ITEMS NOT SHOWN
H337
H308D
109
E512B
AH203
108
113
B643
114
H333
106
107
H612
H770
105
112
H390A
104
E515
P685
103
H389
H246
102
111
E564
101
110
P709
A926
H225
G091
97
99
G090
96
98
100
P726
H297
H304
H490
92
93
P682
91
94
P684
90
95
H204
H135
88
89
H378
H201
86
B119A
85
87
B102
B119
83
84
P708
H203
80
H484
G052
79
82
H213
81
nut, hex, 1/4-20 s/s
washer, 1/4" lock, s/s
H215
77
78
valve, float, autofill
nipple, 12" x 1/4" npt, m x m
B115
H541
cover, sol tank (m-series)
plate, dual manifold, 9" x 13"
vac support, 3 stage, 4-1/16"
gasket, vacuum motor
DESCRIPTION
75
6
76
H253
G212
H501
72
73
G004
71
74
PART NO.
ITEM
NO.
5
5
1
1
1
1
1
2
1
1
QTY.
1
1
QTY.
2
2
1
1
3
3
4
1
1
1
1
4
2
2
1
1
1
1
1
1
1
6
6
2
2
2
2
1
2
2
1
1
1
1
1
1
2
6
4
2
1
1
1
1
6
2
QTY.
$3.19 ea
$3.99 ea
$10.99 ea
$0.99 ea
$3.99 ea
$3.99 ea
MSRP
$4.99 ea
$9.99 ea
MSRP
$0.99 ea
$1.99 ea
$8.99 ea
$9.99 ea
$0.99 ea
$0.99 ea
$13.99 ea
$38.99 ea
$47.99 ea
$4.99 ea
$9.99 ea
$0.99 ea
$6.99 ea
$10.99 ea
$0.99 ea
$62.49 ea
$20.99 ea
$243.99 ea
$15.99 ea
$11.99 ea
$36.99 ea
$0.99 ea
$0.99 ea
$11.49 ea
$18.49 ea
$7.99/ft
$6.99 ea
$3.99 ea
$0.99 ea
$0.99 ea
$8.99 ea
$6.49 ea
$3.99 ea
$17.99 ea
$4.99 ea
$210.99 ea
$0.99 ea
$1.99 ea
$0.99 ea
$0.99 ea
$124.99 ea
$23.99 ea
$12.99 ea
$14.99 ea
$4.99 ea
$8.99 ea
MSRP
4
4
3
3
2
2
M-5 M-SERIES™ PARTS & PRICING
Part prices are subject to change.
12
A
B
C
D
E
F
29
30
31
31
29
32
32
# 75
28
33
34
8
27
57
35
36
11
41
to pump "OUT"
thru B186
# 33
to vac tank
thru B130
41
8
24
to auto fill thru
B115
8
25
6
34
37
31
26
24
38
42
55
11
23
to B644 #
6
24
22
40
# 29
21
# 57
7
to regulator
thru B652
to sol tank
thru B103
39
59
60
# 41
to sol tank
thru B186
7
43
2
20
# 53
to male
garden hose,
B642
41
41
58
24
25
19
# 24
to B105
# 37
to female QD
thru B111
18
12
11
61
56
24
45
32
5
# 115
to vac tank
thru B216
17
20
2
64
62
6
46
6
6
39
40
55
6
47
6
4
6
7
8
15
3
48
63
16
# 107
to pressure gauge
thru B643
3
44
20
2
68
9
54
53
1
52
49
# 43
to sol tank
thru B210
21
13
# 10
5
6
10
2
39
to pump out "OUT"
thru B132
51
50
14
65
69
5
6
73
69
# 54
21
2
8
20
2
37
29
75
74
88
to female
garden hose
thru B196
12
23
79
22
# 24
to auto fill
thru B105
65
66
64
66
67
71
72
70
21
70
87
78
29
33
4
# 24
to regulator
thru B105
31
31
86
79
22
41
22
79
76
77 78
4
8
8
43
80
8
# 25
to 500psi
pump "IN"
thru B160
115
8
85
81
83
3
37
3
44
82
112
110
# 61
to 500 PSI
pump "OUT"
thru Ah195
111
113
90
108
3
# 63
2
to 500 PSI pump
thru Ah108S
91
114
109
92
93
3
89
94
2
29
103
8
# 7
8
DATE
5/24/11
31
NAME
115
84
106
98
M. LaBarbera
96
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
43
to pump out "IN"
thru B236
107
95
TITLE:
104
102
101
100
1
SCALE: 1:5
DO NOT SCALE
DRAWING
M5
REV
OD
SHEET 2 OF 2
M Series
858-679-1191
# 38
to prime valve
thru B106
SIZE DWG. NO.
D
105
99
mytee PRODUCTS, INC.
33
97
1
A
B
C
D
E
F
M-5 PARTS & PRICING
13
A
B
C
D
E
F
8
8
115V
Top Cord
115V
Red
Green
White
7
Black
White
Green
Bottom Cord
7
White
Brown
6
Pump
500psi
Vacuum
6
Blue
Black
Red
White
5
Amber
Light
5
Red
Red
Green
4
Green
4
3
White
Black
Blue
3
Black
Black
White
Black
2
Vacuum
Yellow
Brown
Yellow
Pump
Out
2
NAME
J.Cash
DATE
9/10/2010
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
1
SCALE: 1:2
D
858-679-1191
DO NOT SCALE
DRAWING
M5
REV
SHEET 1 OF 1
M Series
SIZE DWG. NO.
TITLE:
mytee PRODUCTS, INC.
1
A
B
C
D
E
F
M-5 WIRING DIAGRAM
M-12
M-12 FRONT
M-12 BACK
11
1
2
10
20
12
3
9
19
13
4
14
15
5
8
1. Switch plate
2. 2” Male Cuff-Lynx™
3. Female quick disconnect (QD)
4. Front handles
5. Prime valve
7
16
6
17
6. Pressure regulator
7. Front cooling fan
8. 4” locking casters
9. Solution tank
10. Solution tank cover
11. Recovery tank lid
12. Push handle
13. Drain valve
14. Auto-fill
15. Auto pump-out
M-12 ITEMS INCLUDED
18
16. Rear cooling fan
17. Dual power cords
18. 12” rear wheels
19. Latches (x2)
20. Recovery tank
M-12 DUAL CORDS
Top cord: Plug into power Vacuum 1, 2 & Pump-out.
Bottom cord: Plug into power Pump-Mode: Carpet & Tile.
H110 Cuff-Lynx™
2” Hose Adapter
Top cord
H141 Cuff-Lynx™
2” Hose Reducer to 1.5”
Bottom cord
H375 Hose Hanger
(4) screws
H226 Drain Elbow
Plug each of the two power cords into two separate, 20A grounded
wall outlets. The amber light indicator on the switch plate will illuminate when cords are plugged into two separate circuits.
14
M-12
M-12 VAC/SOL HOSE CONNECTIONS
M-12 SWITCHES & PRESSURE GAUGE
1
VAC
UT
MP O
PU
2
VAC
DE
P MO
PUM
CAR
PET
TILE
Switches and Pressure Gauge are located on the plate in front
of the machine. The Amber light left of the Pressure Gauge will
illuminate when cords are plugged into two separate circuits. To
use vacuums, turn on Vac 1 and Vac 2 switches. To use Pump-out,
turn on Pump-out switch. To use on carpet, turn the Pump Mode switch
to Carpet. To use for Tile, turn the Pump Mode switch to Tile. The Pressure Gauge displays the water pressure as PSI.
Before turning on switches, connect hoses to the extractor and a
wand or tool. Attach a solution hose to the front QD, the other end
to the tool. Attach a vacuum hose to the tool, the other to the front
Cuff-Lynx™ vacuum hose port. Just twist into place.
M-12 CARPET MODE
ON
PUMP MODE
CARPET
Press left side of Pump mode button for Carpet. The Amber light left of the Pressure Gauge will illuminate when cords are plugged into two
separate circuits. Two red lights left of switches will appear when Carpet mode is activated. In carpet cleaning mode, a 220 PSI pump and
solution heater are used. The 220 PSI is not adjustable. Adjusting the regulator in this mode will not affect the pump pressure.
15
M-12
M-12 TILE MODE
ON
PUMP MODE
TILE
Press right side of Pump mode button for Tile. The Amber light left of the Pressure Gauge will illuminate when cords are plugged into two
separate circuits. In Tile cleaning mode, a 1200 PSI pump will be used. Pump pressure is set using the regulator on the front of the unit.
There is no heat in tile mode. It is not possible to run the heater and 1200 PSI pump simultaneously.
M-12 FILL SOLUTION TANK
M-12 AUTO-FILL & PUMP-OUT
AUTO-FILL
PUMP-OUT
If not using the Auto-fill feature, lift the solution tank lid and manually fill
the tank.
If using Auto-fill and Pump-out, connect one end of a 1/2 inch
garden hose to the top hose inlet in back of the machine, the other
end to a faucet. Add water pressure by turning on faucet. Attach a
second 1/2 inch garden hose to the bottom hose inlet, and place
the other end in a location where dirty water can drain.
16
M-12
M-12 AUTO-FILL & FLOAT
M-12 PRIME VALVE & PRESSURE REGULATOR
PRIME VALVE
1003/1005
HIGHER PSI
PRESSURE
REGULATOR
LOWER PSI
After attaching a garden hose to the Auto-fill inlet, water will fill the
tank to a predetermined level until stopped by the float. As water is
used and the level drops, water will once again enter the tank, and
be stopped again by the float when maximum level is reached.
With each new job, check to make sure float stops water after the
first fill.
Prime the pump by turning the valve to the Prime position for 30
seconds, then turn horizontally to the Run position. Turn the
Pressure Regulator to the left to decrease the water pressure.
Turn the pressure regulator to the right to increase the water
pressure. Monitor pressure while adjusting, using Pressure Gauge
on Switch Panel.
M-12 DRAIN VALVE & LATCHES
M-12 FILTER MAINTENANCE
PUMP-OUT
FILTER
PRIME VALVE
FILTER
CLEAN WATER
INTAKE FILTER
You can drain the recovery tank by using the Drain Valve. When
not using the Auto Pump-out, you can drain the recovery tank by
using the Drain Valve. When the tank is full, an internal ball float
will automatically shut off the vacuum. Attach the 45˚ drain elbow
to the drain spout, and lift up the Drain Valve to empty the tank.
Latches are located in the back to open tank for internal repairs.
To clean the internal filters, lift solution lid and/or remove recovery tank
lid, reach in and twist off. Rinse with clean water and replace.
17
Order parts at: http://www.mytee.com/products/product.php?id=M-12
18
A
B
C
D
E
F
H528
H903A
E573
H274
H275
E574
E519
B207
AH156
G059
H500
G004
P750
H216
H202
H188
H601
H217
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
nipple, brass, 1/4" x close
H221
H220
E550
G131
C381
B113
B643
AH202
B135
C359A
B186
B652
PH615-9
B644
AH117
B111
B106
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
8
adapter, brass, 1/2" barb x 1/4" mpt
hose, pulse, black, 49" (OAL), 1/4" fswl x 1/4" fswl
adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex
H486
63
elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt
sol hose, 1/2", black, 200 psi 200 degree max
pump, 1200 psi
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
adapter, brass, 3/8" female npt x 1/4" male npt
hose, pulse, 3/8" x 34", (OAL)
tee, brass, 1/4" mpt
connector, cord lock
pump out, 115v
tee, brass, 1/4" fpt
nut, lock, 1/2" steel
fitting, strain relief, cord
power cord, pigtail, 30", 12/3, black
latch, front breeze
B196
H230
fitting, brass, 3/4" mgh x 1/2" fpt
screw, 10-32 x 1/2 phil pan
filter, 60 mesh, garden hose
swivel, brass, 3/4" fgh x 1/2" fpt
cap, brass, 3/4", garden hose
vac hose, 2", black, wire reinforced
vac motor, 2 stage high performance
plug, brass, 3/4", garden hose
cuff hose, 2 X 2, wire reinforced
clamp, hose, 2-1/4 dia
bolt, 1/4-20 x 3/4" hex head, s/s
screw, 1/4-20 x 1", phil flat
plate, manifold, parallel
nut, lock, 1/4-20 nylon insert
gasket, vacuum motor
manifold, dual vac, parallel
exhaust boot, plastisol
vac support, 2 stage, 3-1/8"
Thermostat, 310°F ± 10°F, Manual, 1/4"
heating rod, 1000W, 115V
elbow, brass, 90 deg, 1/4" fpt x 1/4" fpt
hose, 3/8" x 6.5" (OAL), f x fs, 5400 gray
6-32 x 3/16 p-pan internal sem zinc
Thermostat, 200°, Auto, 1/4"
phil pan head screw zinc, 6-32 x 3/16"
bracket, heater mounting, dual
heater, aluminum cast, single
washer, 11/16"id x 1-1/2"od x .075, s/s
clamp, hose, 5/16-29/32
screw, #10-32 x 3/4" phil pan head, zinc
washer, zinc, 1.625 x .847 x .078
sol hose, 1/2" black, 200 psi 200 degree max
elbow, brass, 90 deg, 1/2" barb x 3/8" fpt
screw, 10 x 5/8" hex head, zinc
adapter, brass, 1/2" barb x 1/2" mpt
fan, cooling, 115V
washer, 1/4"id x 1"od, flat, s/s
handle, breeze and dx
screw, 10-32 x 5/8" hex head, zinc
guard, cooling fan, wire
washer, 9/16"id x 1"od, flat, s/s
qd, brass, 1/4" f
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
bolt, 1/4-20 x 1" hex head, s/s
washer, 1/4" lock, s/s
nipple, brass, 1/4"m, hex
nut, hex, 1/4-20 s/s
caster, 4", black hub & gray tread
washer, axle, cut 1/2" id
axle, 19.75" x .50"
base, m series
washer, 1/4" flat, s/s
nut, kep, #10-32 zinc
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
61
62
B640
B642
B120
H299
H347
H256
30
31
32
58
59
60
H191
PH615-36
B236
28
29
H544
H343
B132
27
PH628-21
C310
B221
C317
24
25
26
55
56
57
H211
H485
H206
H296
23
54
H212
B102
H768
H342
H213
B107
17
18
19
20
21
22
H215
H668
15
16
wheel, 12"
H251
H219
10
H254
H232
P707
H210
H273
B103
7
8
9
11
cap, axle, 1/2"
H185
C322D
5
6
12
13
14
valve, brass, 1/4" check
hose, 3/8" x 14-1/2" (OAL), f
elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt
bushing, brass, 3/8"mpt x 1/4"
B108
AH184
B136
B105
screw, 10-32 x 1-1/4", phil flat full thread, black oxide
pump, 200psi, bypass, 115V
DESCRIPTION
8
PART NO.
ITEM
NO.
1
2
3
4
7
7
1
1
1
2
1
1
1
4
1
1
2
2
1
1
2
2
2
2
1
18
1
1
1
1
2
1
1
3
10
3
1
9
2
1
2
6
2
2
1
1
8
2
10
1
2
9
16
6
2
1
2
8
2
1
8
2
4
3
2
2
10
8
12
3
16
2
4
1
1
2
2
24
20
7
4
1
1
1
2
5
new/QTY.
$3.49 ea
$3.49 ea
$2.49 ea
$8.49 ea
$8.99 ft
$708.99 ea
$8.99 ea
$4.99 ea
$39.99 ea
$5.49 ea
$4.99 ea
$187.49 ea
$6.99 ea
$1.99 ea
$3.19 ea
$11.49 ea
$13.99 ea
$5.99 ea
$0.99 ea
$1.99 ea
$5.49 ea
$1.49 ea
$8.99/ft
$103.99 ea
13.99 ea
$12.49 ea
$1.49 ea
$0.99 ea
$0.99 ea
$13.49 ea
$0.99 ea
$8.99 ea
$15.99 ea
$4.99 ea
$3.99 ea
$17.99 ea
$51.99 ea
$5.99 ea
$23.99 ea
$0.99 ea
$16.49 ea
$0.99 ea
$29.99 ea
$78.99 ea
$0.99 ea
$1.99 ea
$0.99 ea
$1.99 ea
$8.99 ft
$14.49 ea
$0.99 ea
$9.49 ea
$21.49 ea
$0.99 ea
$6.99 ea
$0.99 ea
$2.99 ea
$0.99 ea
$17.99 ea
$0.99
$0.99 ea
$0.99 ea
$3.19 ea
$0.99 ea
$19.49 ea
$0.99 ea
$9.99 ea
$196.99 ea
$41.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$4.49 ea
$0.99 ea
$208.99 ea
$13.99 ea
$27.99 ea
$4.99 ea
$3.19 ea
MSRP
washer, buna 1-1/8" od x 3/16" id
cover, sol tank (m-series)
nipple, 12" x 1/4" npt, m x m
valve, float, autofill
PH634-36
B109
PH634-20
G034
B656
B119A
B210
B216
H378
H201
H316
G052
G212
B115
H541-A
H203
P708
AH101
H308D
E516
E515
E511
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
G090
H304
G091
A926
P709
H225
H390A
H770
H333
P685
117
118
119
120
121
122
123
124
125
126
MATERIAL
Part prices are subject to change.
6
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE FINISH
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
ANGULAR:
.5
ONE PLACE DECIMAL
.005
TWO PLACE DECIMAL
.003
THREE PLACE DECIMAL .001
M. LaBarbera
COMMENTS:
CHECKED
DRAWN
7/10/11
5
MSRP
$10.99 ea
$243.99 ea
$20.99 ea
$6.99 ea
$0.99 ea
$9.99 ea
$11.99 ea
$15.99 ea
$36.99 ea
$0.99 ea
$11.49 ea
$18.49 ea
$0.99 ea
$7.99/ft
$3.99 ea
$6.49 ea
$6.99 ea
$0.99 ea
$9.99 ea
$8.99 ea
$0.99 ea
$14.99 ea
$13.99 ea
$5.99 ea
$0.99 ea
$210.99 ea
$22.99 ea
$38.99 ea
$124.99 ea
$1.99 ea
$12.99 ea
$23.99 ea
$0.99 ea
$0.99 ea
$8.99 ea
$13.49 ea
$6.49 ea
$2.49 ea
$1.99 ea
$6.49 ft
$0.99 ea
$6.49 ft
$1.99 ea
$86.99 ea
$4.49 ea
$4.99 ea
MSRP
$3.99 ea
$10.99 ea
$3.99 ea
$3.19 ea
$0.99 ea
$3.99 ea
MSRP
$6.49 ft
$3.49 ea
$62.49 ea
$9.99 ea
$74.99 ea
DO NOT SCALE
DRAWING
5
M12
D
SCALE: 1:8
REV
OD
SHEET 1 OF 2
M Series
SIZE DWG. NO.
TITLE:
858-679-1191
1
1
1
1
2
1
1
1
1
QTY
1
1
1
1
2
QTY.
1
1
1
2
4
1
1
1
1
6
1
1
3
1
1
2
1
3
1
1
3
1
3
2
2
1
1
1
1
6
1
1
2
2
1
1
1
2
2
1
1
1
2
1
1
1
new/QTY.
mytee PRODUCTS, INC.
hanger, wire formed, hose
banana bag, mash bag, yellow
H375
G029
DATE
Cuff-Lynx, 2" ro 1.5" reducer
spout, drain, 45 degree
screw, 10-32 x 1/2" phil pan head s/s
H141
H226
H230
NAME
stop sign, register your product
Cuff-Lynx, 2" hose x 2" fem swivel Cuff-Lynx
AD127
H110
UNLESS OTHERWISE SPECIFIED:
DESCRIPTION
manual, m-series
Cuff-Lynx instruction guide
PART NO.
ADM-M-SERIES
ADM-Cuff-Lynx
ACCESSORIES
sol hose, 1/4", kuri
strap, velcro, w/buckle
G147
PH634-36
controller, circuit light
filter, bag, vac tank, drawstring
E564
G010
DESCRIPTION
power cord, ext, 50', 12/3, black
E530
inlet, 2"
vac tank, m series
valve, drain, 1-1/2"
bracket, "L" (all extracters)
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
mesh filter, auto dump, 1/2" npt
gasket, 7", vac lid
elbow, inlet assembly 2"
lid, vac tank, black, 7"
screw, #8 x 5/8 phil oval, s/s
elbow, 2" float
float, 2", ball style
screw, #8 x 1/2", hex head, zinc
pipe, pvc, 2"
Cuff-Lynx, 2" m cuff x 2" mpt
gasket, cam fitting polyethylene, 2.35" OD 1.90" ID
adaptor, pvc 2, fmsl x fmt
washer, #8 flat, s/s
light, indicator, 125v (amber)
plate, switch, sp, 4 hole w/gauge
screw, #10-32 x 1/2" SHCS, alloy
PART NO.
ITEMS NOT SHOWN
P726
H490
P682
113
H297
110
111
112
114
H135
G002
P684
107
108
109
115
116
H389
H612
E512B
H337
106
switch, rocker, 3 position
switch, rocker, 2 position
light, red, 250v
bolt, 1/4-20 x 1-1/4" hex head
sol tank, m series
hose, pulse, black, 76" (OAL), 1/4" fsw x 3/8" msw
gauge, pressure, 2000 PSI
bolt, 1/4-20 x 1/2", hex head, zinc
bolt, 1/4-20 x 1-1/2" hex head, s/s
bracket, front hinge, sp/fb
ball valve, 1/4''
filter, strainer, 1/2"
bushing, brass, 1/2"mpt x 3/8" fpt, hex
nipple, brass, 3/8" x close
sol hose, 1/4", 300 PSI
grommet, rubber, 3/4" ID x 1-5/8" OD
sol hose, 1/4", 300 PSI
adapter, brass, 1/4" barb x 1/4" mpt
regulator, 1000 psi, white spring
coupling, brass, 1/4" fpt x 1/4" fpt
plate, mounting, QD
B142A
H484
C359C
DESCRIPTION
83
6
PART NO.
ITEM
NO.
81
82
4
4
3
3
M-12 PARTS & PRICING
A
B
C
D
E
F
# 97
to auto fill
thru B115
33
8
32
4
34
50
39
49
51
39
48
38
8
45
# 59
to male
garden
hose
thru B642
31
35
42
46
41
36
37
40
15
47
52
53
25
24
26
30
9
44
23
28
2
21
29
7
# 43
to heater
"IN" thru
B207
# 2
20
32
7
18
19
# 21
17
to QD
(lower)
thru B107
# 1
to 220 psi
pump "OUT"
thru B108
to heater
"OUT" thru
AH184
22
43
27
22
56
55
54
7
16
1
15
68
33
2
14
8
35
2
9
64
32
32
13
12
61
62
6
8
7
# 72
3
to sol tank
thru B135
8
65
29
66
# 91
to vac tank
thru B216
# 9
# 78
4
6
5
11
59
67
60
63
72
4
58
7
69
70
4
10
H191 # 29
to pump-out
"OUT" thru
# 31
to auto fill
thru B132
57
# 61
19
50
to female
garden
hose thru B196
71
30
to QD
(upper)
thru AH117
to 220 psi
pump "IN"
thru B130
6
49
5
5
7
94
23
77
95
24
73
97
79
74
74
76
18
93
9
92
75
# 71
to 220/1200 psi
pumps "IN"
thru AH202
7
49
22
96
33
74
15
18
95
98
90
23
# 101
to pressure
guage
thru AH101
74
95
4
33
91
33
99
# 4
89
23
87
to auto fill
thru B105
4
21
86
100
72
85
88
82
85
19
83
84
80
62
81
79
78
9
3
3
# 19
to 1200 psi
pump "OUT"
thru B107
102
9
101
103
104
111
106
107
108
110
2
91
33
90
125
117
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
ANGULAR:
.5
ONE PLACE DECIMAL
.005
TWO PLACE DECIMAL
.003
THREE PLACE DECIMAL .001
120
121
119
118
DATE
7/10/11
NAME
124
123
M. LaBarbera
COMMENTS:
CHECKED
DRAWN
# 32
to pump-out
"IN' thru B236
UNLESS OTHERWISE SPECIFIED:
126
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE FINISH
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
# 74
8
116
107
109
to 12oo psi
pump "OUT"
thru B186
105
106
111
112
113
114
115
2
858-679-1191
DO NOT SCALE
DRAWING
1
M12
D
SCALE: 1:7
REV
OD
SHEET 2 OF 2
M Series
SIZE DWG. NO.
TITLE:
mytee PRODUCTS, INC.
122
1
C
D
E
F
REV
M12 updating
19
A
B
D
8
M-12 PARTS & PRICING
20
A
Black
White
B
White
Green
115v
Pump
200
Pump
1200
Pump
Out
Green
Green
Top
Cord
Black
White
115v
Bottom
Cord
B
White
Black
Black
Motor
2
C
White
Motor
1
Blue
Red
Green
C
Yellow
H2
H1
1000W
4
3
2
1
Mytee Products, Inc.
M12 Wiring Diagram
A
D
D
Red
Blue
Brown
SW4
SW3
SW2
SW1
E
E
4
3
2
1
M-12 WIRING DIAGRAM
1000W
M-16
M-16 FRONT
M-16 BACK
11
1
2
10
20
12
3
9
19
13
4
14
15
5
8
1. Switch plate
2. 2” Male Cuff-Lynx™
3. Female quick disconnect (QD)
4. Front handles
5. Prime valve
7
16
6
17
6. Pressure regulator
7. Front cooling fan
8. 4” locking casters
9. Solution tank
10. Solution tank cover
11. Recovery tank lid
12. Push handle
13. Drain valve
14. Auto-fill
15. Auto pump-out
M-16 ITEMS INCLUDED
18
16. Rear cooling fan
17. Dual power cords
18. 12” rear wheels
19. Latches (x2)
20. Recovery tank
M-16 DUAL CORDS
Top cord: Plug into power Vacuum 1 & 2.
Bottom cord: Plug into power Pump & Pump-out.
H110 Cuff-Lynx™
2” Hose Adapter
Top cord
H141 Cuff-Lynx™
2” Hose Reducer to 1.5”
Bottom cord
H375 Hose Hanger
(4) screws
H226 Drain Elbow
Plug each of the two power cords into two separate, 20A grounded
wall outlets. The amber light indicator on the switch plate will illuminate when cords are plugged into two separate circuits.
21
M-16
M-16 VAC/SOL HOSE CONNECTIONS
M-16 SWITCHES & PRESSURE GAUGE
1
VAC
UT
MP O
2
VAC
P
PUM
PU
Before turning on switches, connect hoses to the extractor and a
wand or tool. Attach a solution hose to the front QD, the other end
to the tool. Attach a vacuum hose to the tool, the other to the front
Cuff-Lynx™ vacuum hose port. Just twist into place.
Switches and Pressure Gauge are located on the plate in front of
the machine. The Amber light left of the Pressure Gauge will illuminate when cords are plugged into two separate circuits. To use
vacuums, turn on Vac 1 and Vac 2 switches. To use Pump, turn on
Pump switch. The Pressure Gauge displays the water pressure as
PSI. To use Pump-out feature, turn on Pump-out Switch.
M-16 FILL SOLUTION TANK
M-16 AUTO-FILL & PUMP-OUT
AUTO-FILL
PUMP-OUT
If using Auto-fill and Pump-out, connect one end of a 1/2 inch
garden hose to the top hose inlet in back of the machine, the other
end to a faucet. Add water pressure by turning on faucet. Attach a
second 1/2 inch garden hose to the bottom hose inlet, and place
the other end in a location where dirty water can drain.
If not using the Auto-fill feature, lift the solution tank lid and manually fill
the tank.
22
M-16
M-16 AUTO-FILL & FLOAT
M-16 PRIME VALVE & PRESSURE REGULATOR
PRIME VALVE
1003/1005
HIGHER PSI
PRESSURE
REGULATOR
LOWER PSI
After attaching a garden hose to the Auto-fill inlet, water will fill the
tank to a predetermined level until stopped by the float. As water is
used and the level drops, water will once again enter the tank, and
be stopped again by the float when maximum level is reached.
With each new job, check to make sure float stops water after the
first fill.
Prime the pump by turning the valve to the Prime position for 30
seconds, then turn horizontally to the Run position. Turn the
Pressure Regulator to the left to decrease the water pressure.
Turn the pressure regulator to the right to increase the water
pressure. Monitor pressure while adjusting, using Pressure Gauge
on Switch Panel.
M-16 DRAIN VALVE & LATCHES
M-16 FILTER MAINTENANCE
PUMP-OUT
FILTER
PRIME VALVE
FILTER
CLEAN WATER
INTAKE FILTER
You can drain the recovery tank by using the Drain Valve. When
not using the Auto Pump-out, you can drain the recovery tank by
using the Drain Valve. When the tank is full, an internal ball float
will automatically shut off the vacuum. Attach the 45˚ drain elbow
to the drain spout, and lift up the Drain Valve to empty the tank.
Latches are located in the back to open tank for internal repairs.
To clean the internal filters, lift solution lid and/or remove recovery tank
lid, reach in and twist off. Rinse with clean water and replace.
23
Order parts at: http://www.mytee.com/products/product.php?id=M-16
24
A
B
C
D
E
F
P707
H232
H254
H251
H219
B196
B120
B642
B640
15
16
17
18
19
20
21
22
PH715-27
B242
B652
B111
AH104
H306B
B160
PH615-22
B644
C359A
AH203
PH615-34
B186
55
56
57
58
59
60
61
62
63
64
65
66
67
H541
B235
54
70
B107
B172
H212
52
53
PH615-8
G059
51
69
H217
50
68
H500
C310
49
47
48
H544
G004
46
P750
H188
43
PH628-20
H202
42
45
H601
41
44
B105
AH202
B210
38
40
PH615-37
37
39
C381
36
B132
32
H222
H191
31
35
H221
30
H347
H220
29
PH615-17
E550
28
34
G131
27
33
H486
H230
25
26
B221
H342
13
14
H273
H668
12
24
H210
11
23
H458
B103
7
10
H768
6
B656
H211
5
H216
H485
4
9
H343
3
8
H296
C317
1
2
PART NO.
ITEM
NO.
bolt, 1/4-20 x 3/4" hex head, s/s
plate, manifold, parallel
hose, pulse, 3/8" x 34" OAL
bushing, brass, 3/8"mpt x 1/4"
bushing, brass, 1/2"mpt x 3/8" fpt, hex
sol hose, kuriama, 1/2"
pump out, 115v
screw, #10-32 x 1-1/4" phil pan head, zinc
sol hose, kuriama, 1/2"
clamp, hose, 5/16-29/32
adapter, brass, 1/2" barb x 1/2" mpt
washer, zinc, 1.625 x .847 x .078
nut, lock, 1/2" steel
fitting, strain relief, cord
power cord, pigtail, 30", 12/3, black
connector, cord lock
screw, 10-32 x 1/2 phil pan
latch, front breeze
nut, kep, #10-32 zinc
plug, brass, 3/4", garden hose
filter, 60 mesh, garden hose
swivel, brass, 3/4" fgh x 1/2" fpt
cap, brass, 3/4", garden hose
fitting, brass, 3/4" mgh x 1/2" fpt
cap, axle, 1/2"
wheel, 12"
washer, axle, cut 1/2" id
axle, 19.75" x .50"
base, m series
bolt, 1/4-20 x 1" hex head, s/s
caster, 4", black hub & gray tread
washer, 1/4" flat, s/s
nut, lock, 10-32, thin pattern
nut, lock, 1/4-20 nylon insert
ball valve, 1/4''
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
washer, 1/4"id x 1"od, flat, s/s
handle, breeze and dx
screw, #10 x 5/8" hex head zinc
guard, cooling fan, wire
fan, cooling, 115V
DESCRIPTION
8
valve, float, autofill
sol hose, 1/2" kuri 100psi
elbow, brass, 90 deg, 1/2" barb x 3/8"mpt
elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt
sol hose, 1/2" kuri 100psi
hose, pulse, 3/8" x 34", OAL
pump, 1200 psi
adapter, brass, 1/2" barb x 1/4" mpt
sol hose, 1/2" kuri 100psi
adapter, brass, 1/2" barb x 3/8" fsw, ball end
unloader, 1200 psi
sol hose, 3/8" x 10"
adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex
elbow, brass, 90 deg, 3/8"mpt x 1/4"mpt
tee, brass, 3/8" fpt x 3/8" mpt x 3/8" fpt
sol hose, kuriyama, 3/8"
adapter, brass, 3/8" barb x 1/4" fsw
nipple, brass, 1/4"m, hex
washer, 9/16"id x 1"od, flat, s/s
exhaust boot, plastisol
clamp, hose, 2-1/4 dia
vac motor, 2 stage high performance
vac support, 2 stage, 3-1/8"
gasket, vacuum motor
cuff hose, 2 X 2, wire reinforced
vac hose, 2", black, wire reinforced
manifold, dual vac, parallel
screw, 1/4-20 x 1, phil flat full thread, blacl oxide
8
7
Part prices are subject to change.
7
1
1
1
5
1
2
1
3
1
2
1
2
6
1
2
1
2
3
6
2
3
2
6
2
1
1
1
3
10
1
1
7
3
1
1
4
1
24
1
2
2
2
2
2
18
2
14
1
1
1
1
1
2
2
4
1
1
8
2
24
3
14
1
7
10
8
2
15
3
1
QTY.
$124.99 ea
$8.99/ft
$9.49 ea
$8.99 ea
$8.99/ft
$47.99 ea
$708.99 ea
$2.49 ea
$8.99/ft
$3.49 ea
$126.49 ea
$47.99 ea
$3.49 ea
$8.49 ea
$13.99 ea
$7.99/ft
$7.99 ea
$3.19 ea
$0.99 ea
$4.99 ea
$1.49 ea
$103.99 ea
$3.99 ea
$8.99 ea
$12.49 ea
$8.99/ft
$15.99 ea
$0.99 ea
$0.99 ea
$13.49 ea
$39.99 ea
$3.19 ea
$2.49 ea
$8.99/ft
$187.49 ea
$0.99 ea
$8.99/ft
$1.99 ea
$9.49 ea
$1.99 ea
$1.99 ea
$3.19 ea
$11.49 ea
$4.99 ea
$0.99 ea
$13.99 ea
$0.99 ea
13.99 ea
$1.99 ea
$5.49 ea
$1.49 ea
$5.99 ea
$0.99 ea
$41.99 ea
$0.99 ea
$9.99 ea
$196.99 ea
$0.99 ea
$19.49 ea
$0.99 ea
$0.99 ea
$0.99 ea
$13.49 ea
$4.49 ea
$0.99 ea
$0.99 ea
$6.99 ea
$0.99 ea
$2.99 ea
$21.49 ea
MSRP
B130
81
H389
87
88
B236
98
H304
washer, 1/4" lock, s/s
Cuff-Lynx, 2" m cuff x 2" mpt
nipple, brass, 1/4" x close
filter, strainer, 1/4"
elbow, brass, 90 deg, 1/2" barb x 3/8" fpt
mesh filter, auto dump, 1/2" npt
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
bracket, "L" (all extracters)
vac tank, m series
plate, switch, sp, 4 hole w/gauge
gauge, pressure, 2000 PSI
light, indicator, 125v (amber)
switch, rocker, 2 position
washer, #8 flat, s/s
screw, #10-32 x 1/2" SHCS, alloy
bolt, 1/4-20 x 1-1/4" hex head, s/s
nut, hex, 1/4-20 s/s
sol, hose, 57 x 1/4"
plate, mounting, QD
qd, brass, 1/4" f
filter, strainer, 1/2"
45 deg, street elbow, brass, 1/4" male NPTF
nipple, brass, 3/8" x close
bolt, 1/4-20 x 1-3/4" hex head, s/s
bolt, 1/4-20 x 1/2", hex head, zinc
6
hanger, wire formed, hose
H375
controller, circuit light
filter, bag, vac tank, draw string
E564
G010
DESCRIPTION
gasket, strip, 3/4" x 36" x 1/8"
G085
screw, #8 x 5/8 phil oval, s/s
lid, vac tank, black, 7"
gasket, 7", vac lid
float, 2", ball style
elbow, 2" float
pipe, pvc, 2"
adaptor, pvc 2, fmsl x fmt
inlet, 2"
valve, drain, 1-1/2"
elbow, inlet assembly 2"
1
1
1
2
QTY
5
MSRP
$0.99 ea
$36.99 ea
$11.99 ea
$18.49 ea
$11.49 ea
$7.99/ft
$6.99 ea
$10.99 ea
$20.99 ea
$15.99 ea
$6.49 ea
$3.99 ea
$3.49 ea
$3.99 ea
$14.49 ea
$9.99 ea
$0.99 ea
$6.99 ea
$243.99 ea
$8.99 ea
$38.99 ea
$9.99 ea
$13.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$37.99 ea
$4.99 ea
$17.99 ea
$6.49 ea
$5.49 ea
$1.99 ea
$0.99 ea
$0.99 ea
$0.99 ea
$8.99 ea
$1.99 ea
$12.99 ea
$210.99 ea
$0.99 ea
$23.99 ea
$10.99 ea
$9.99 ea
$62.49 ea
$4.99 ea
MSRP
6
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
2
1
1
1
1
4
3
3
2
2
1
1
1
1
2
2
2
2
4
1
6
1
bracket, front hinge, sp/fb
washer, buna 1-1/8" od x 3/16" id
cover, sol tank (m-series)
11
1
QTY.
1
5
sol tank, m series
washer, 11/16"id x 1-1/2"od x .075, s/s
nipple, 12" x 1/4" npt, m x m
DESCRIPTION
gasket, cam fitting polyethylene, 2.35" OD 1.90" ID
6
PART NO
ITEMS NOT SHOWN
G090
110
112
H490
G091
109
111
P726
P682
107
108
P684
104
106
H225
103
P685
A926
102
105
H135
G002
101
B106
H333
97
B119
H770
96
99
H390A
95
100
P709
H337
93
94
E512B
H308D
91
92
E515
H203
86
90
H215
85
H612
AH195
84
89
B102
H484
83
B119A
B216
80
82
H204
79
H201
H378
76
H213
G052
75
78
G212
74
77
P708
73
B115
H299
71
72
PART NO.
ITEM
NO.
4
4
3
3
2
M-16 PARTS & PRICING
2
25
A
B
C
D
E
F
# 67
To auto fill
thru B186
8
8
40
41
42
31
37
38
43
10
# 21
To B642
45
3
7
4
2
# 53
1
To regulator
thru B107
24
11
35
36
# 98
To vac tank
thru B236
44
7
51
50
48
5
34
6
# 7
8
53
6
7
# 85
# 53
33
55
32
52
To q.d
thru AH195
54
49
To PH715-27
thru B107
To ball valve
thru B103
47
46
31
7
39
54
# 19
To B196
56
52
# 58
39
57
58
53
6
13
12
11
9
30
# 67
To sol tank
thru B105
60
53
# 7
63
61
58
29
14
7
59
To ball valve
thru B103
To vac tank
thru B111
6
28
15
# 38
To AH202
thru B210
33
33
58
16
21
62
9
22
58
27
20
23
19
11
39
42
61
65
33
24
5
# 67
17
26
25
To sol tank
thru B186
64
5
18
66
# 32
To pump
out "OUT"
thru B132
63
# 65
39
To pressure
guage
thru AH203
77
78
63
76
11
39
56
67
67
11
75
# 40
79
72
72
6
73
72
39
71
58
74
5
To AH202
9
4
69
68
67
4
67
4
72
72
# 61
72
80
67
72
72
82
# 61
52
38
To pump "IN"
thru B160
39
70
To regulator
thru B160
7
52
81
7
3
83
86
77
75
5
58
3
26
84
87
88
# 39
To regulator
thru B105
85
5
75
89
90
93
# 65
To pump "OUT"
thru AH203
92
91
2
65
24
2
94
95
96
# 37
98
72
80
72
97
72
38
To pump out "IN"
thru PH615-37
24
7
105
106
107
3
108
110
111
DATE
5/25/11
NAME
M. LaBarbera
58
100
81
99
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
109
112
858-679-1191
103
104
DO NOT SCALE
DRAWING
1
M16
D
SCALE: 1:6
REV
OD
SHEET 2 OF 2
M Series
SIZE DWG. NO.
TITLE:
mytee PRODUCTS, INC.
# 54
To PH715-27
thru B235
52
52
101
102
1
A
B
C
D
E
F
M-16 PARTS & PRICING
8
8
26
38.27
115V
Top Cord
115V
Red
7
Green
White
Black
White
Green
Bottom Cord
7
White
Blue
6
Vacuum
Pump
1200psi
6
Brown
Black
Red
White
5
Amber
Light
5
Red
Red
Green
4
Green
4
3
NAME
J.Cash
9/10/2010
DATE
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
M16
DO NOT SCALE
DRAWING
D
SCALE: 1:2
2
REV
SHEET 1 OF 1
M Series
SIZE DWG. NO.
Yellow
Brown
Vacuum
858-679-1191
Black
Yellow
Pump
Out
2
mytee PRODUCTS, INC.
TITLE:
Black
Black
White
PROPRIETARY AND CONFIDENTIAL
CHECKED
DRAWN
White
Black
Blue
3
1
M-16 WIRING DIAGRAM
1
General information
Dear Customer:
Unpacking the Machine
Keep in mind that the M-Series™ Extractor is a machine, so neglect or abuse will
cause unnecessary damage and void the warranty. However with simple maintenance the M-Series™ will give quality performance for many years to come.
Caution and Warnings
Congratulations on the purchase of your new M-Series™ Extractor. As you are
already aware, the scene of the equipment world is becoming more high tech, and
we at Mytee Products Inc. strive to keep you on the cutting edge with superior quality
and technology.
When the machine is delivered, carefully inspect the shipping carton and the
machine for damage. If damage is evident, save the shipping carton so that it can
be inspected by the carrier that delivered it. Contact the carrier immediately to file a
freight damage claim.
Symbols
Mytee uses the symbols below to signal potentially dangerous conditions. Always
read this information carefully and take the necessary steps to protect personnel
and property.
If warranty questions arise, please consult user manual or get in touch with your
distributor. If you have questions about maintenance, replacing parts or ordering
parts, please call an authorized Mytee Products Inc. Service Center. To see an
updated list, visit our website at www.mytee.com
Is used to warn of immediate hazards that will cause severe personal injury or death.
Before you begin using, please read your manual thoroughly.
Sincerely,
Mytee Customer Care Dept.
Is used to call attention to a situation that could cause severe personal injury.
Grounding Instructions
This machine must be grounded. If it should malfunction or breakdown, grounding
provides a path of least resistance for electrical shock. This machine is equipped
with a cord having an equipment-grounding conductor and grounding plug. The plug
must be plugged into an appropriate outlet that is properly installed in accordance
with all local code and ordinances. Do not remove ground pin; if missing, replace
plug before use.
Is used to call attention to a situation that could cause minor personal injury or
damage to the machine or other property. When using an electrical appliance, basic
precautions should always be followed, including the following: Read all instructions
before using this machine. This product is intended for commercial use only.
To reduce the risk of fire, electrical shock, or injury:
1. Read all instructions before using equipment.
2. Use only as described in this manual. Use only manufacturer’s recommended
attachments.
3. Always unplug power cord from electrical outlet before attempting any adjustments
or repairs.
4. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
5. Do not pull or carry by cord. Do not close a door on cord or pull cord around sharp
edges or corners.
6. Do not run appliance over cord. Keep cord away from heated surfaces.
7. Do not use with damaged cord or plug. If cord is damaged, repair immediately.
8. Do not use outdoors or on wet surfaces and or standing water.
9. Always unplug or disconnect the appliance from power supply when not in use.
10. Do not allow to be used as a toy. Close attention is necessary when used by or
near children.
11. Do not use in areas where flammable or combustible material may be present.
12. Do not leave the unit exposed to harsh weather elements. Temperatures below
freezing may damage components and void warranty.
13. Use only the appropriate handles to move and lift unit. Do not use any other parts
of this machine for this purpose.
14. Keep hair, loose clothing, fingers, and all parts of the body away from all
openings and moving parts.
15. Use extra care when using on stairs.
16. To reduce the risk of fire or electric shock, do not use this machine with a solidstate speed control device.
17. The voltage and frequency indicated on the name plate must correspond to the
wall receptacle supply voltage.
18. When cleaning and servicing the machine, local or national regulations may apply
to the safe disposal of liquids which may contain: chemicals, grease, oil, acid,
alkalines, or other dangerous liquids.
19. Do not leave operating unattended.
Improper connection of the equipment-grounding conductor can result in a risk
of electric shock. Check with a qualified electrician or service person if you are in
doubt as to whether the outlet is properly grounded. Do not modify the plug provided
with the machine. If it will not fit the outlet, have a proper outlet installed by a
qualified electrician.
This appliance is for use on a nominal 120-volt circuit, and has a grounding plug
that looks like the plug illustrated in Figure 1 below. A temporary adapter illustrated
in Figures 2 and 3 may be used~to connect this plug to a 2-pole receptacle as
shown in Figure 2 if a properly grounded outlet is not available. The temporary
adapter should be used only until a properly grounded outlet (Figure 1) can be
installed by a qualified electrician. The green colored rigid ear, tab or the like
extending from the adapter must be connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the adapter is used, it must be held
in place by a metal screw. Grounding adapters are not approved for use in Canada.
Replace the plug if the grounding pin is damaged or broken.
The Green (or GreenYellow) wire in the cord is the grounding wire. When replacing
a plug, this wire must be attached to the grounding pin only.
DO NOT use extension cords.
Please Note for America use only
Grounded Outlet
Adapter
Metal
Screw
Grounding Pin
Grounded Outlet Box
Figure 1
Parts and Service
Figure 2
Pre-Operation
Tab for Grounding
Screw
1. Remove furniture and other items from the area you are going to clean.
2. Vacuum area and remove debris.
3. Protect cabinets, walls and painted surfaces with drop cloths or plastic.
4. Inspect power cord for damage.
Figure 3
Repairs, when required, should be performed by Mytee service personnel or Mytee
authorized Service Center using Mytee original replacement parts and accessories.
Call Mytee for repair parts or service. Please specify the Model and Serial Number
when discussing your machine.
Operating Instructions
1. Fill the solution tank.
2. If using the auto-fill and pump-out, connect one end of a ½” garden hose to the
top hose inlet in back of the machine, the other end to a faucet. Attach a second ½”
garden hose to the bottom hose inlet, and place the other end in a location where
dirty water can drain.
3. If manually filling and emptying the tank, keep both back hose inlets securely
capped.
4. In front, attach one end of a solution hose from a wand or other tool to the front
quick disconnect.
Name Plate
The Model and Serial Number of your machine are shown on the name plate located
on the inside of the machine. This information is needed when ordering repair parts
for the machine. Use the space provided on the front cover to note the Model and
Serial Number of your machine for future reference.
27
General Information
5. Attach one end of the vacuum hose from a wand or other attachment to the front
Cuff-Lynx™ vacuum hose port.
6. Plug in power cords.
• M-3 – Plug the top power cord into a 20A grounded wall outlet to turn on Vac 1,
Pump and Heater 1. Using a second 20A grounded wall outlet on a separate circuit,
plug in the bottom cord to turn on Vac 2, Pump-out and Heater 2. The amber light
indicator on the switch plate will illuminate brightly when cords are plugged into two
separate circuits. Do not use extension cords longer than 50 feet.
• M-5 – Plug the top power cord into a 20A grounded wall outlet to turn on Vac 1 and
Pump. Using a second 20A grounded wall outlet on a separate circuit, plug in the
bottom cord to turn on Vac 2 and Pump-out. The amber light indicator on the switch
plate will illuminate brightly when cords are plugged into two separate circuits. Do not
use extension cords longer than 50 feet.
• M-12 – Plug the top power cord into a 20A grounded wall outlet to turn on Vac 1
and 2, and Pump-out. Using a second 20A grounded wall outlet on a separate circuit,
plug in the bottom cord to turn on the Pump-Mode for carpet and tile. The amber light
indicator on the switch plate will illuminate brightly when cords are plugged into two
separate circuits. Do not use extension cords longer than 50 feet.
• M-16 – Plug the top power cord into a 20A grounded wall outlet to turn on Vac 1
and Vac 2. Using a second 20A grounded wall outlet on a separate circuit, plug in the
bottom cord to turn on Pump and Pump-out. The amber light indicator on the switch
plate will illuminate brightly when cords are plugged into two separate circuits. Do not
use extension cords longer than 50 feet.
7. Prime the pump by turning the valve to the Prime position and turning on the pump
for 30 seconds, then turn left to the Run position.
8. Turn on vacuum and pump switches. The Amber light left of the Pressure Gauge
will illuminate when cords are plugged into two separate circuits.
•M-3 - To use vacuums, turn on Vac 1 and Vac 2 switches. To use Pump, turn on
Pump switch. Heater switch has three positions: Off (middle); 1,000 watts using one
heater (left); and 2,000 watts using two heaters (right). Red lights on panel display
indicate watts selected: one light = 1,000 watts; two lights = 2,000 watts; no lights =
heaters is off.
•M-5 – Turn on Vac 1 and Vac 2 switches. If using Pump-out feature, turn on Pumpout switch. To use pump, turn on the Pump switch.
•M-12 – Turn on Vac 1 and Vac 2 switches. If using Pump-out feature, turn on Pumpout switch. In carpet cleaning mode, a 220 PSI pump and solution heater are used.
The 220 PSI is not adjustable. Adjusting the regulator in this mode will not affect
the pump pressure. Two red lights left of switches will appear when Carpet mode is
activated. In Tile cleaning mode, a 1200 PSI pump will be used. Pump pressure is
set using the regulator on the front of the unit. There is no heat in Tile mode. It is not
possible to run the heater and 1200 PSI pump simultaneously.
•M-16 – Turn on Vac 1 and Vac 2 switches. To use Pump-out feature, turn on
Pump-out switch. To use pump, turn on Pump switch.
9. To adjust water pressure, turn the pressure regulator, located on the lower front
of the extractor, to the right to increase water pressure. Turn to the left to decrease
water pressure. Level will be visible on the pressure gauge.
10. Begin cleaning. Make two dry passes to every wet pass. Work away from cords
to avoid damage. To clean heavily soiled areas, repeat cleaning from different
directions.
11. Use a foam control solution in the recovery tank to prevent vacuum motor damage and check for foam build-up in recovery and solution tanks.
12. When not using the Auto Pump-out and using the recovery tank, an internal ball
float will automatically stop the vacuum when tank fills. Empty the tank by using the
rear drain valve.
13. Relieve water pressure from the solution hose before disconnecting it, squeeze
the tools trigger five seconds after turning the power switches off.
14. Once machine is off unplug power cords. Remove solution and vacuum hoses.
To empty the recovery tank, if Pump-out is not used, attach the 45˚ drain elbow to the
drain sprout in back. Lift up the dump valve to empty the tank.
15. To empty remaining water in the solution tank, turn the Prime Valve to the right
and turn on pump to move water into the recovery tank. Empty recovery tank.
3. Jets clogged, remove jet and flush clean.
4. Filters clogged, remove filters and rinse clean with water.
5. Heater is blocked; flush out with Mytee’s® System Maintainer.
6. If brass check valve is stuck, replace valve.
7. Check pump wire. May need to reconnect wire.
8. Switch plate may need to be replaced.
9. If pump motor brushes are worn, replace pump.
M-3 or M-12 heater does not work properly
1. If sensor mounted on the heater has popped, reset sensor by pushing in button.
2. Heating element may need to be replaced.
Vacuum motor does not work properly
1. Check that hose is tightly connected.
2. Close drain hose valve completely.
3. Secure the vacuum tank tightly.
4. If ball float is shut off, empty vacuum tank of all wastewater.
5. Make sure ball float is firmly installed on the elbow.
6. If water is coming out of the vacuum motor, use a low foaming detergent.
7. Clean upholstery tool or floor wand jets.
Maintenance Schedule
Latches are located in back to open tank for internal maintenance. To keep machine
in good working condition, follow machine’s daily and weekly maintenance procedures. Check valves and relief valves should be replaced annually.
Maintenance item
Daily
Flush pump-out with clear water.
Clean and inspect tanks.
Clean and inspect hoses.
Check and clean internal filters by twisting off, rinsing
with clean water and replacing.
Check power supply cable.
Clean machine with all-purpose cleaner and cloth.
Check spray nozzles.
Flush solution system with Mytee® System Maintainer.
Remove and float shut-off screen from tank and clean.
Simply pull off.
Inspect vacuum hoses for holes and loose cuffs.
Inspect spray pattern for clogging. If clogged, remove
spray tips and soak them in a recommended liquid
neutralizer for up to six hours. To remove spray tip,
twist spray tip body counter-clockwise.
Lubricate wheels with water resistant oil.
Inspect machine for water leaks and loose hardware.
x
x
x
x
x
x
Once a week
x
x
x
x
x
x
x
FAQs
Q: How much do the M-Series™ Extractors weigh and what are dimensions?
A: M-3:
Machine Weight – 147.2 lbs.
Shipping Weight – 179.2 lbs.
Machine Dimensions – 35 1/4” x 19 1/2” x 43”
Shipping Dimensions – 37 1/4” x 21” x 50 3/4”
M-5:
Machine Weight – 141 lbs.
Shipping Weight – 172.6 lbs.
Machine Dimensions – 35 1/4” x 19 1/2” x 43”
Shipping Dimensions – 37 1/4” x 21” x 50 3/4”
M-12:
Machine Weight – 168 lbs.
Shipping Weight – 200 lbs.
Machine Dimensions – 35 1/4” x 19 1/2” x 43”
Shipping Dimensions – 37 1/4” x 21” x 50 3/4”
M-16:
Machine Weight – 152 lbs.
Shipping Weight – 183.6 lbs.
Machine Dimensions – 35 1/4” x 19 1/2” x 43”
Shipping Dimensions – 37 1/4” x 21” x 50 3/4”
After Use
1. Before storing machine, drain, rinse and dry tanks and vacuum hose of water
and solution.
2. Store in a dry area in the upright position.
3. Open recovery tank cover to promote air circulation.
4. Make sure the machine and solution system are completely drained and dry.
Trouble Shooting
Q: What comes standard with M-Series™ Extractors?
A: Hose hanger with four screws, two Cuff-Lynx™ Model Nos.: H141 Reducer and
H110 Coupler Swivel and 45˚ drain elbow.
There is no power.
1. Plug machine in proper outlet.
2. Check circuit breaker. Reset circuit breaker, other items should not run on the
same circuit as the machine. Must be two 20-amp circuit outlets.
Q: Does Mytee® recommend tools for this machine?
A: All upholstery tools, wands and Spinners® can be used with the M-Series™.
Pump does not work properly
1. Snap quick disconnects firmly together.
2. Check solution tank; may be empty.
28
General information
then the remaining provisions and portions shall remain valid and enforceable.
If any provision or portion of this limited warranty policy is found to be limited by law,
then that provision or portion shall be construed to make it effective within the
bounds of law. For example, if there are legal limitations on the duration of warranties, the warranties made herein shall be construed to have the minimum duration
required by law, or, if there are legal limitations of exclusion of remedies, the exclusions made herein shall be construed to apply to the fullest extent possible without
violating the law.
Q: Where do I plug the machine in?
A: Into two separate 20A grounded circuits.
Q: How will I know when I find two separate circuits?
A: The amber indicator light on the switch plate will illuminate when the power cords
are plugged into two separate circuits.
Q: Are pumps rebuildable for the M-Series™?
A: For a 1200 PSI pump, available rebuildable kits are: RK0034 seal & piston kit,
RL0038 valve & o-ring kit, and RL0033 cam & bearing kit. For a 500 PSI pump,
available rebuildable kits are: RK0022 seal & piston kit, RL0023 valve & o-ring kit
and RK0024 cam & bearing kit.
The validity, construction and performance of this warranty policy shall be governed
by the laws of the State of California, without respect to conflicts of laws principles.
The exclusive jurisdiction of any legal action arising from or related to this warranty
policy shall be in the State of California and no legal action shall be commenced
elsewhere.
Q: Is there anything I can do to increase the expected life of my machine?
A: Running the vacuum motors with the tank empty and lid off will allow excess
moisture in the vacs to dry off. You should also run Mytee’s® System Maintainer
through the system to keep the hoses, pump, and heater clean and free of debris.
Return Material Authorization Procedure
It is the responsibility of any Authorized Service Center (ASC) or Distributor with
written authorization to ensure the Customers equipment is repaired as soon as
possible. Only Mytee Products Inc. or it’s authorized dealers with written authorization, service centers, and agents may make warranty repairs on these products. All
others do so at their own risk and expense.
Warranty
MYTEE LIFETIME LIMITED WARRANTY POLICY
Mytee Products, Inc. endeavors to provide high quality products and product support
to its customers and therefore backs up all of its new products purchased from Mytee
Products Inc. (“Mytee”) or any authorized Mytee distributor/service center with this
lifetime limited warranty. This limited warranty begins on the date of the customer’s
purchase and is valid and available to the original purchaser with proof of purchase,
and is not transferable. Mytee’s products are for commercial use only and are not
intended for personal, family or household uses.
The Distributor must follow Mytee Products, Inc. standard RMA procedure:
1. When a repair falls within the Warranty time period for a piece of equipment, the
Distributor will fill out a RMA/Warranty claim form. This form will act as a repair order
to replace any defective parts.
2. All defective parts must be returned to Mytee Products, Inc. with the RMA/claim
form for evaluation at the customer’s expense. This shipping is non-refundable. All
warranty claims are subject to an evaluation by Mytee Products, Inc. to determine if
warranty will be approved. Any credit for repair and/or parts will only be issued upon
evaluation and approval from Mytee Products, Inc.
HOUSING LIMITED LIFETIME WARRANTY: Mytee warrants for life that its rotationally-molded housings will be free from manufacturing defects. This warranty covers
the cost of replacement or repair only and does not cover shipping or labor costs.
WEAR PARTS 90-DAY LIMITED WARRANTY: Mytee will replace all wear parts for
90 days from the date of original purchase. “Wear parts” are items which wear out
as a result of usage or the passage of time and are consumed despite attempts to
maintain them, such as gaskets, wheels, brass, cords, wires, electrical terminals,
hoses, switches, thermostats, plastisol parts, filters, bearings, brushes, solenoids,
o-rings, bulbs, heating elements, castors, or other parts deemed wear items in
Mytee’s sole discretion. This warranty covers the cost of replacement only and does
not cover shipping or labor costs.
3. When Warranty is approved, the Distributor’s account will be credited for the
replacement part(s). Mytee Products, Inc. will ship the warranted replacement part(s)
to the Distributor prepaid. If Warranty is denied the Distributor’s account will not be
credited for any parts sent for this claim.
HOWEVER, OTHER THAN SET FORTH HEREIN, MYTEE GIVES NO WARRANTY,
EXPRESS OR IMPLIED, AS TO DESCRIPTION, QUALITY, MERCHANTABILITY,
FITNESS FOR ANY PARTICULAR PURPOSE, PRODUCTIVENESS, INFRINGEMENT, OR OTHER MATTER, OF ANY GOODS WHICH MYTEE SHALL SUPPLY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION
ON THE FACE HEREOF. MYTEE SHALL IN NO WAY BE RESPONSIBLE FOR THE
PROPER USE AND APPLICATION OF THE GOODS. MYTEE NEITHER ASSUMES
NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR MYTEE ANY OTHER
LIABILITY IN CONNECTION WITH THE SALE OF MYTEE’S GOODS. THIS LIMITED WARRANTY POLICY MAY BE CHANGED OR WITHDRAWN BY MYTEE AT
ANY TIME WITHOUT NOTICE.
LIMITATION OF DAMAGES: THE REMEDY OF REPLACEMENT OR REPAIR
OF ANY DEFECTIVE GOODS SHALL BE THE EXCLUSIVE REMEDY UNDER
ANY WARRANTY MADE BY MYTEE, WHETHER EXPRESS OR IMPLIED. IN NO
EVENT SHALL MYTEE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES, PROPERTY DAMAGES, OR PERSONAL INJURIES.
All limited warranties are void for, and Mytee does not warrant in any way, any product that evidences misapplication, improper installation, abuse, lack of maintenance,
negligence in use or care, abnormal use, alteration of design, modification, use of
incompatible or corrosive chemicals, use in a rental service, and/or servicing, installation of parts, or repairs by anyone other than Mytee or a Mytee authorized distributor
or service center. Mytee may make changes in products it manufactures and markets
at any time; these changes are made without obligation to change, retrofit, or upgrade any product previously sold or manufactured.
Mytee has no obligation to honor the limited warranties set forth herein unless the
original purchaser, promptly upon discovering the warranty claim and prior to continuing to use the product, contacts Mytee or a Mytee authorized distributor or service
center to describe the claim and to receive and follow instructions for documenting
and resolving the claim. In addition, the purchaser must provide the product to which
the claim applies to Mytee or a Mytee authorized distributor or service center for a
thorough inspection. In addition, the purchaser must provide/return the product intact,
unmodified, with all of its original parts.
If any provision or portion of this limited warranty policy is found to be unenforceable,
29
NOTES
30
Mytee Products Inc.
13655 Stowe Dr.
Poway, Ca. 92064
www.mytee.com
PH 858.679.1191
F X 858.679.7814
© 2012 Mytee Products Inc.
Printed in the U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising