Korenix 8152 JetBox 8152 JetBox User Manual

Korenix 8152 JetBox 8152 JetBox User Manual

Below you will find brief information for 8152 JetBox 8152. The 8152 JetBox 8152 is a device with built-in Ethernet port and serial ports. It can be used for applications that require a small footprint, such as industrial controllers, communications hubs, and point-of-sale terminals. The 8152 JetBox 8152 is equipped with a variety of features, including a web server, FTP server, and Telnet server, which allow you to manage and monitor the device remotely.

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

JetBox 8152 User Manual | Manualzz
JetBox 8152 User Manual
WinCE 5.0
www.korenix.com
Copyright Notice
Copyright© 2011 Korenix Technology Co., Ltd.
All rights reserved.
Reproduction without permission is prohibited.
Information provided in this manual is intended to be accurate and reliable.
However, the original manufacturer assumes no responsibility for its use, or for
any infringements upon the rights of third parties that may result from its use.
The material in this document is for product information only and is subject to
change without notice. While reasonable efforts have been made in the
preparation of this document to assure its accuracy, Korenix assumes no
liabilities resulting from errors or omissions in this document, or from the use of
the information contained herein.
Korenix reserves the right to make changes in the product design without
notice to its users.
Acknowledgments
Korenix is a registered trademark of Korenix Technology Co., Ltd.
All other trademarks or registered marks in the manual belong to their
respective manufacturers.
Korenix | Table of Content
2
Table of Content
Copyright Notice ................................................................................ 2
Acknowledgments.............................................................................. 2
Table of Content ............................................................................................... 3
Chapter 1
Introduction ................................................................................. 6
1-1
Applied Models .............................................................................. 6
Chapter 2
Software Specifications .............................................................. 7
2-1
Application – End User................................................................... 7
2-2
Applications and Services Development ........................................ 7
2-3
2-4
2-5
Communication Services and Networking ...................................... 9
Core OS Service .......................................................................... 13
Device Management .................................................................... 14
2-6
File System and Data Store ......................................................... 15
2-7
Graphics and Multimedia Technologies........................................ 15
2-8
Security ........................................................................................ 16
2-9
Shell and User Interface ............................................................... 17
2-10
Platform Manager ..................................................................... 18
Chapter 3
Software Feature ...................................................................... 19
3-1
Customized Control Applets ......................................................... 19
3-1-1
Overview ........................................................................... 19
3-1-2
Serial Port Throughput ...................................................... 19
3-1-3
Version Utilities .................................................................. 21
3-1-4
Canver Utilities .................................................................. 22
3-2
Customized System Utilities ......................................................... 23
3-2-1
Overview ........................................................................... 23
3-2-2
User manager Utility .......................................................... 23
3-2-3
Registry Flush Utility .......................................................... 24
3-2-4
Auto Run Utility.................................................................. 25
3-3
Telnet Server ................................................................................ 28
3-4
FTP Server ................................................................................... 30
3-5
Web Server .................................................................................. 33
3-6
File Server .................................................................................... 38
Chapter 4
Web-based Administration ........................................................ 41
Korenix | Table of Content
3
4-1
4-2
Overview ...................................................................................... 41
Remote Administration Page (RemoteAdmin) .............................. 41
4-2-1
Introduction........................................................................ 41
4-2-2
First use Setup Wizard ...................................................... 42
4-2-3
RemoteAdmin Home Page ................................................ 44
4-2-4
Device Management Pages .............................................. 46
4-3
Web Administration Page (WebAdmin) ........................................ 51
4-3-1
Introduction........................................................................ 51
4-3-2
4-3-3
4-3-4
4-3-5
4-3-6
4-4
WebAdmin Home Page ..................................................... 51
Instructions Page............................................................... 53
Logging Page .................................................................... 54
SSL Configuration Page .................................................... 56
Restart Web Server Page .................................................. 57
System Administration Page (SysAdmin) ..................................... 58
4-4-1
Introduction........................................................................ 58
4-4-2
SysAdmin Home Page ...................................................... 58
4-4-3
System Tools Page ............................................................ 59
4-4-4
File Browser Page ............................................................. 61
4-4-5
Registry Editor Page ......................................................... 62
Chapter 5
Connectivity Features ............................................................... 64
5-1
Overview ...................................................................................... 64
5-2
ActiveSync Connection ................................................................ 64
5-2-1
Introduction........................................................................ 64
5-2-2
Connection via COM port .................................................. 65
5-2-3
Explore JetBox .................................................................. 73
5-3
Manual Server Connection ........................................................... 74
5-3-1
Overview ........................................................................... 74
5-3-2
Configure Platform Manager ............................................. 74
5-3-3
Telnet with JetBox ............................................................. 76
5-3-4
Remote Tools via Manual Server Connection.................... 78
Chapter 6
Application Development .......................................................... 81
6-1
Overview ...................................................................................... 81
6-2
Install JetBox SDK ....................................................................... 81
6-3
Hello Word Application with eVC++ 4.0 ........................................ 86
6-4
Hello World Application with VS2005 ........................................... 92
Chapter 7
Appendix .................................................................................. 97
7-1
Table List ...................................................................................... 97
Korenix | Table of Content
4
7-2
7-3
7-4
Figure List .................................................................................... 98
Revision History ......................................................................... 101
Customer Service....................................................................... 101
Korenix | Table of Content
5
Chapter 1 Introduction
Microsoft® Windows® CE 5.0 is an open, scalable, 32-bit operating system
(OS) that integrates reliable, real time capabilities with advanced Windows
technologies. Windows CE allows you to build a wide range of innovative,
small footprint devices. A typical Windows CE–based device is designed for a
specific use, which often runs disconnected from other computers, and
requires a small OS that has a deterministic response to interrupts. Examples
include enterprise tools, such as industrial controllers, communications hubs,
and point-of-sale terminals, and consumer products, such as cameras, Internet
appliances, and interactive appliances (HMI).
1-1
Applied Models
JetBox 8152
Note: In WnCE5.0, the JetBox8152 did not provide the audio function because
the audio chip vender did not support the driver for WinCE5.0.
Korenix | Introduction
6
Chapter 2 Software Specifications
2-1
Application – End User
Applications – End
User
Description
ActiveSync
This item provides support for
synchronizing data between a
Windows-based desktop computer and
Microsoft® Windows® CE-based devices.
CAB File
Installer/Uninstaller
This item includes an application that
enables installing and uninstalling CAB
files. This application is for use with
devices that include a display.
Table 1 Application – End User
2-2
Applications and Services Development
Applications and
Services
Development
Description
.NET Compact
Framework 1.0
The Microsoft® .NET Compact Framework
1.0 is a hardware-independent program
execution environment for applications that
target resource-constrained computing
devices. This environment offers a choice of
languages, Microsoft Visual Basic® and
Microsoft Visual C#® , and lessens
problems with language interoperability.
.NET Compact
Framework 2.0 SP2
The Microsoft® .NET Compact Framework
2.0 is a hardware-independent program
execution environment for applications that
target resource-constrained computing
Korenix | Software Specifications
7
Applications and
Services
Development
Description
devices. This environment offers a choice of
languages, Microsoft Visual Basic® and
Microsoft Visual C#® , and lessens
problems with language interoperability.
Active Template Library Includes support for Active Template Library
(ATL)
for Windows CE.
Microsoft Foundation
Classes (MFC)
MFC for Windows CE is a comprehensive
class library and complete object-oriented
application framework designed to help
build applications, COM components, and
controls. You can create anything from a
simple dialog box–based application to a
sophisticated application that uses the full
MFC document or view architecture.
C libraries and
Runtimes
Supports full ANSI C run time, compiler C++
exception handling equivalent to the
desktop C++ compilers, compiler Run-Time
Type Information (RTTI) equivalent to the
desktop C++ compilers, the standard
input/output library, the standard
input/output ASCII library and the standard
ASCII string functions.
Component Object
The Component Object Model (COM) is a
Model (COM & DCOM) platform-independent, object-oriented
system for creating binary software
components that can interact with other
COM-based components in the same
process space, in other processes, or on
remote devices.
Message Queuing
The Message Queuing implementation in
(MSMQ)
Microsoft® Windows® CE makes it possible
for applications to communicate with other
applications across networks and systems
that might be temporarily offline.
Korenix | Software Specifications
8
Applications and
Services
Development
Description
Object Exchange
Protocol (OBEX)
The Object Exchange Protocol (OBEX)
technology for Microsoft® Windows® CE
provides an efficient, compact binary
protocol that enables a wide range of
devices to exchange data spontaneously in
a simple, efficient manner.
SOAP Toolkit
The client-side SOAP Toolkit functionality in
Microsoft® Windows® CE allows an
application to invoke Web service
operations, while the server-side
functionality maps invoked Web service
operations to Component Object Model
(COM) object method calls.
SQL Server CE2.0
SQL Server CE extends Microsoft SQL
Server to Microsoft Windows CE-based
mobile devices. SQL Server CE delivers
relational database functionality, including a
data store, a query processor, and scalable
connectivity capabilities, all in a small
footprint.
XML
Extensible Markup Language (XML) is the
universal format for data on the Web. XML
allows developers to describe and deliver
rich, structured data from any application in
a standard, consistent way. XML does not
replace HTML; rather, it is a complementary
format.
Table 2 Applications and Services Development
2-3
Communication Services and Networking
Communication
Services and
Networking
Description
Korenix | Software Specifications
9
Communication
Services and
Networking
Description
Wired Local Area
Network (802.3, 802.5)
This item provides support for wired local
area networks that use 802.3 and 802.5.
Dial Up Networking
(RAS/PPP)
This item provides support for accessing
network resources on a remote computer.
Point-to-Point Protocol
This item includes the ability to connect
over Ethernet (PPPoE)
hosts to a Remote Access Concentrator.
Telephony API (TAPI
2.0)
This item includes an API that simplifies and
abstracts the details of making telephony
connections between two or more devices.
Virtual Private
This Item includes a Layer Two Tunneling
Networking (VPN)
Protocol (L2TP)/IP Security Protocol
(IPSec) implementation that enable a more
secure virtual private network (VPN)
connection to a server computer. This item
includes a Point-to-Point Tunneling Protocol
(PPTP) implementation that enables a
virtual private network connection a server
computer.
Domain Discovery
Domain Discovery for Microsoft®
Windows® CE 5.0 enables a Windows CE
device to discover an Active Directory
server to query.
Extensible
The Extensible Authentication Protocol
Authentication Protocol implementation in Microsoft® Windows®
CE allows third-party authentication code to
interact with the implementation of the
Point-to-Point Protocol (PPP) included in
the Windows CE–based Remote Access
Service (RAS). The Extensible
Authentication Protocol (EAP) is also used
with 802.1x and EAP over LAN (EAPOL)
authentication.
Firewall
The IP firewall is typically used on an
Internet gateway device. It can also be used
Korenix | Software Specifications
10
Communication
Services and
Networking
Description
as a host firewall. The firewall protects the
device on which it runs and protects
devices on the private side of the gateway.
The firewall blocks IP traffic at the IP and
transport layers.
Internet Connection
Sharing (ICS)
Internet Connection Sharing (ICS) for
Microsoft® Windows® CE consists of a
collection of technologies and services that
make it possible to connect multiple
computing and information devices on a
network located in a home, a small
business, or a corporate branch office to the
Internet through a single Internet
connection.
IPSec v4
IPSec v4 enables two client devices on a
network to establish peer-to-peer
communication using the IP Security
(IPSec) protocol. This technology enables
Windows CE-based devices to participate in
networks that are secured by IPSec.
NDIS Packet Capturing NDIS Packet Capturing captures network
traffic so that it can be read by the Microsoft
Windows Network Monitor (NetMon).
Network Utilities
The Network Utilities includes IPConfig,
IPv6tun, NetStat, Ping, Route and Tracert
that you can use to troubleshoot network
connections in your Windows CE-based
device.
TCP/IP
TCP/IP for Microsoft® Windows® CE
allows devices to participate as peers and
servers on local area networks (LANs) and
remote networks.
Windows Networking
API/Redirector
The Windows Networking API/Redirector
(SMB/CIFS) implementation in Microsoft®
Korenix | Software Specifications
11
Communication
Services and
Networking
Description
Windows® CE provides functions to
establish and terminate network
connections and to access files on servers
supporting the Common Internet File
System (CIFS). Access to this data is made
possible by way of the networking API
(WNet).
Winsock
Windows Sockets (Winsock) for Microsoft®
Windows® CE specifies a programming
interface based on the familiar socket
interface from the University of California at
Berkeley. It includes a set of extensions
designed to take advantage of the
message-driven nature of Windows CE.
Windows CE .NET 4.1 and later supports
Winsock 2.2, which provides easier access
to multiple transport protocols.
File Server
The File Server functionality in Microsoft®
Windows® CE enables clients to access
files and other resources over the network.
Ftp Server
The FTP Server implementation in
Microsoft® Windows® CE can copy files to
and from remote computer systems over a
network using TCP/IP. The source code is
provided to you as is, so that you can
customize the implementation for your
specific requirements.
SNTP Client and
Server
Windows CE supports the Simple Network
Time Protocol (SNTP) technology.
Telnet Server
The Telnet Server functionality in
Microsoft® Windows® CE provides a
sample Telnet server can be installed on a
device to allow remote administration
through a standard Telnet client. Using the
Korenix | Software Specifications
12
Communication
Services and
Networking
Description
Telnet sample, the current device can be
manipulated as if it is running the command
prompt on the device itself.
Web Server
The Web Server (HTTPD) implementation
in Microsoft® Windows® CE enables you to
monitor, configure, and remotely control a
device or computer through the use of a
Hypertext Transfer Protocol (HTTP) server.
The Web server provides this service for
network printers, scanners, and other
shared equipment.
Table 3 Communication Service and Networking
2-4
Core OS Service
Core OS Services
Description
Kernel Features
This item includes Fiber API, Format
Message API, Memory Mapped Files, and
Message Queue Point-to-Point.
Device Drivers
This item includes display, serial port, USB
host, etc… drivers
Device Manager
Tracks all loaded device drivers and their
interfaces, and issues notifications when
device interfaces are added or removed.
The Device Manager registers special file
names with the kernel that do the following
tasks:
Map the stream interface functions
Load and track drivers by reading and
writing registry values
Unload drivers when their devices are no
longer needed
PNP Notifications
A functionality of the ―AdvertiseInterface‖
system. This functionality is automatically
Korenix | Software Specifications
13
Core OS Services
Description
included if either Storage Manager or
Device Manager is selected.
Power Management
A fully implemented Power Manager
framework, including all APIs and features.
Power Manager applications and drivers
can do the following tasks:
Suspend the system
Control device power levels
Register for notifications of power-related
activities such as suspend, absence of
user/system activity, and change in battery
level.
Drivers can intelligently self-manage power.
USB Human Input
Device (HID) Class
A sample USB class driver that supports
HID-compatible USB devices on a run-time
Driver
image.
USB Printer Class
Driver
A sample USB class driver that supports
USB printer-class-compatible devices on a
run-time image.
USB Remote NDIS
Class Driver
A sample USB class driver that supports
Remote NDIS-compatible Ethernet
adapters.
USB Storage Class
Driver
A sample USB class driver that supports
USB Storage-class compatible devices.
Table 4 Core OS Service
2-5
Device Management
Device Management
Description
Device Management
Client
Provides support for the Device
Management Client in the run-time image.
Simple Network
Management Protocol
Provides support for the Simple Network
Management Protocol (SNMP) in the
run-time image.
Table 5 Device Management
Korenix | Software Specifications
14
2-6
File System and Data Store
File System and Data
Store
Description
Bit-based
Provides support for the Device
Management Client in the run-time image.
Compression
Provides support for the Simple Network
Management Protocol (SNMP) in the
run-time image.
Database support
An API that provides built-in CEDB
database support.
Hive-based Registry
A registry system that stores data inside
files, or hives, which can be kept on any file
system
RAM and ROM File
A file system driver capable of reading data
System
from the ROM file system and the RAM file
system in the object store.
Storage Manager
The Storage Manager is responsible for all
external storage items, such as file
systems, file system filters, and partitioning
System Password
An API that provides support for
authentication on a device to prevent
unauthorized access.
Table 6 File System and Data Store
2-7
Graphics and Multimedia Technologies
Graphics and
Multimedia
Technologies
Description
Audio
Supports Waveform audio.
Graphics
Supports Alphablend API, Direct3D Mobile,
Direct Draw, and Gradient Fill.
Imaging
Support image decoders and encoders for
BMP, GIF, ICO, JPG and PNG formats.
Audio Codecs and
Includes G.711 Audio Codec, GSM 6.10
Korenix | Software Specifications
15
Graphics and
Multimedia
Technologies
Description
Renderers
Audio Codec, IMA ADPCM Audio Codec,
MP3 Codec, MPEG-1 Layer 1 and 2 Audio
Codec, MS ADPCM Audio Codec,
Wave/AIFF/au/snd File Parser, Waveform
Audio Renderer, WMA Codec and WMA
Voice Codec.
DirectShow
Includes ACM Wrapper Filter, DirectShow
Core, DirectShow Display, DirectShow
Error Messages and DMO Wrapper Filter.
Media Formats
Includes AVI Filter and MPEG-1
Parser/Splitter.
Video Codecs and
Renderers
Includes DirectShow Video Renderer,
MPEG-1 Video Codes, MS RLE Video
Codec, Overlay Mixer, Video/Image
Compression Manager and WMV/MPEG-4
Video Codec.
WMA and MP3 Local
Playback
This item provides support for playing
Windows Media Audio (.wma) or MP3 files
from local storage such as system memory
or Compact Flash memory. This is an
audio-only item and does not provide any
video playback capabilities
Table 7 Graphics and Multimedia Technologies
2-8
Security
Security
Description
Authentication
Services (SSPI)
This catalog item includes support for a
programming interface for user
authentication, and message protection.
Available authentication providers include
NTLM, Kerberos, and Secure Sockets
Layer (SSL). Each provider contains
Korenix | Software Specifications
16
Security
Description
different authentication and cryptographic
schemes.
Credential Manager
This item includes a service for caching
credentials, and enabling the sharing of
common credentials.
Cryptography Services
(CryptoAPI 1.0)
This item includes a set of cryptographic
services that provide basic cryptography
support for hashing, encrypting, and
decrypting data.
Local Authentication
Sub-System
This item includes support for the Local
Authentication subsystem (LASS)
infrastructure that will enable application
independent user authentication, provide
consistent authentication regardless of the
mechanism used, and enable policy-based
authentication.
Table 8 Security
2-9
Shell and User Interface
Shell and User
Interface
Description
Graphics, Windowing
and Events
Microsoft® Windows® CE combines the
Microsoft Win32® application programming
interface (API), user interface (UI), and graphics
device interface (GDI) libraries into the Graphics,
Windowing, and Events Subsystem (GWES)
module (Gwes.exe). GWES is the interface
between the user, your application, and the
operating system (OS).
GWES supports all the windows, dialog boxes,
controls, menus, and resources that make up the
Windows CE user interface (UI), which enables
users to control applications. GWES also provides
information to the user in the form of bitmaps,
Korenix | Software Specifications
17
Shell and User
Interface
Description
carets, cursors, text, and icons.
Command Shell
Command-line shell
Standard Shell
Similar to the Windows Explorer shell on
Windows-based desktop operating systems.
User Interface
Includes Common Controls, Common Dialog,
Control Panel Applets, Menu Tool Tip, Mouse,
Network User Interface, Software Input and Panel.
Table 9 Shell and User Interface
2-10 Platform Manager
Platform Manager
Description
Platform Manager
This item is a communications technology
that manages the communications between
a development workstation and a
Microsoft® Windows® CE–based device. It
allows development tools to download and
connect to a target device in a
media-independent manner. Remote tools,
Microsoft eMbedded Visual C++® 4.0 and
later, and the Microsoft .NET Compact
Framework use Platform Manager to
download files such as applications,
Microsoft ActiveX® controls, run times, and
remote-tool clients to a target device.
Table 10 Platform Manager
Korenix | Software Specifications
18
Chapter 3 Software Feature
3-1
Customized Control Applets
3-1-1 Overview
Most of the customized device’s control utilities are implemented as the
applets of the control panel. These utilities could help user to diagnostic the
hardware functionalities. Following figure is the snapshot of the control panel
of JetBox
Figure 1 Snapshot of the Control Panel of JetBox
3-1-2
Serial Port Throughput
The control applet named ―SerPerf‖ provides a simple user interface to test
throughput of the serial ports. Loopback adapters or cables are necessary to
Korenix | Software Feature
19
perform this test. Figure 2 is the configuration snapshot of the ―SerPerf‖ control.
Figure 3 is the snapshot of the ―SerPerf‖ control panel under throughput testing.
Table 11 describes the user interface of ―SerPerf‖.
Note: the layout of the serial ports is platform dependent. Your system may
be different with the following snapshot. In addition, COM4 is a virtual COM
port for USB ActiveSync connection, so it can’t be tested.
Figure 2 Configuration Snapshot of ―SerPerf‖ Control Applet
Figure 3 Run Time Snapshot of ―SerPerf‖ Control Applet
Applet Name: SerPerf
User
Interface
Description
COMx
The ―COMx‖ check box is used to select the
serial ports. Check the box means running a
through test on the port. Uncheck the box means
ignoring the port during testing.
Bits per
Specifies the baud rate at which the
Korenix | Software Feature
20
Applet Name: SerPerf
User
Interface
Description
second
communication device operates.
Data bits
Specifies the number of bits in the bytes
transmitted and received.
Parity
Specifies the parity scheme to be used.
Stop bits
Specifies the number of stop bits to be used.
Flow control
Specifies the flow control scheme to be used.
OK
Starts the throughput test.
X
Exits.
Table 11 Description of the Usr Interface of ―SerPerf‖
3-1-3 Version Utilities
The control applet named ―Version Viewer‖ provides a simple user interface to
show the OS and Boot loader build information. Figure 4 is the snapshot of the
―Version Viewer‖ control applet. Table 12 describes the user interface of
―Version Viewer‖.
Figure 4.Snapshot of “Version Viewer” Control Applet
Applet Name: Version Viewer
User Interface
Description
Build number
Indicates the serial number of the built image.
Korenix | Software Feature
21
Build Date
Indicates the date of the image was built.
Build Time
Indicates the time of the image was built.
Build Platform
Indicates the BSP of the build image.
Build Project
Indicates the workspace of the build image.
Boot Loader
Indicates the version number of the boot loader.
X
Exits.
Table 12 Description of the User Interface of ―Version Viewer‖
3-1-4 Canver Utilities
The control applet named ―Canver Viewer‖ provides a simple user interface to
show the Canbus Driver build information. Figure 5 is the snapshot of the ―Canver
Viewer‖ control applet. Table 13 describes the user interface of ―Canver
Viewer‖.
Figure 5.Snapshot of “Canver Viewer” Control Applet
Applet Name: Canver Viewer
User Interface
Description
Driver Name
Indicates the Driver Name of the built image.
Driver Version
Indicates the canbus version of the driver.
X
Exits.
Table 13 Description of the User Interface of “Canver Viewer”
Korenix | Software Feature
22
3-2
Customized System Utilities
3-2-1 Overview
Lots of system utilities are provides to make using JetBox more convenient.
3-2-2 User manager Utility
Introduction
Microsoft® Windows® CE 5.0 provides authentication services that can be
used by application developers to authenticate clients. Services supported by
Windows CE include security services for user authentication, credential
management, and message protection through a programming interface called
the Security Support Provider Interface (SSPI).
Within SSPI, different security providers are available, such as the NTLM
security support provider (SSP) and Kerberos SSP; each one contains
different authentication and cryptographic schemes.
Windows CE uses the Windows NT® LAN Manager protocol
(RPC_C_AUTHN_WINNT), which is also known as NTLM, to authenticate
callers. This is the default authentication service for communications on
Windows NT.
You can set the domain variable in the DefaultDomain registry value, which is
located under the HKEY_LOCAL_MACHINE\Comm\Redir registry key. If the
DefaultDomain registry value is not set, Windows CE uses the local user
database to set the domain variable.
“UsrMgr.exe” Utility
By Default, JetBox doesn’t set the DefaultDomain registry value under the
HKEY_LOCAL_MACHINE\Comm\Redir registry key. Therefore, one command
line utility named ―UsrMgr.exe‖ is provides for the user to add, delete and list
users and groups that are local to JetBox. Figure 4 shows the snapshot of
―UsrMgr.exe’. Table 12 shows the arguments description of ―UsrMgr.exe‖.
Korenix | Software Feature
23
Figure 6 Snapshot of ―UsrMgr.exe‖
Utility Name: UsrMgr
Arguments
Description
-a <user name> <password>
Adds or updates a user.
-d <user name>
Removes a user.
-l
Lists all users.
-gn <group name>
Creates a new group.
-gd <group name>
Deletes a group.
-gl
Lists all groups.
-gm <group name>
Lists members in a group.
-gat <user name> <group
name>
Adds a user to a group.
-grf <user name> <group
name>
Removes a user from a
group.
Table 134 Arguments Description of ―UsrMgr.exe‖
3-2-3 Registry Flush Utility
Introduction
The hive-based registry stores registry data inside files, or hives, which can be
kept on any file system. This removes the need to perform backup and restore
on power off. Removing this work during boot and power off makes the cold
Korenix | Software Feature
24
boot process faster.
Outstanding registry data will be flushed on a suspend/resume cycle and any
time the system goes through a software shutdown. However, data may be lost
if power is suddenly removed. Because a software shutdown is not an UI
option of JetBox, so to ensure that data is not lost, call RegFlushKey API in
your application. It will flush any unsaved changes in the hive to the persistent
file.
“rFlush.exe” Utility
To save the system resource, JetBox doesn’t implement a daemon to flush
registry data periodically. A utility named ―rFlush.exe‖ is provided to flush the
changed registry data. Figure 5 shows the snapshot of the user interface of
―rFlush.exe‖ utility.
Figure 7 Snapshot of ―rFlush.exe‖
3-2-4 Auto Run Utility
Introduction
When Windows CE begins loading, the kernel starts the file system and
examines the HKEY_LOCAL_MACHINE\Init registry key to identify what
applications to run. To control which applications run at system startup, create
launch registry values. Launch registry values do not need to be sorted in the
registry, although you can specify dependencies. You can specify up to 32
applications. Table 13 shows the named values for the
HKEY_LOCAL_MACHINE\Init registry key.
HKEY_LOCAL_MACHINE\Init
Korenix | Software Feature
25
Value
Description
Launchnn :
String
Specifies the application to launch in order ―nn‖.
Depnednn :
Binary
Launchnn registry values have optional
dependencies as denoted by the Dependnn
registry value.
Table 145 Named Values of HKEY_LOCAL_MACHINE\Init Key
Dependnn registry values specify applications that Windows CE must be
running before the Launchnn applications run.
Dependnn registry values begin with the keyword Depend, followed by the
same decimal number as the Launchnn registry value.
The Dependnn registry values define an order in which Windows CE launches
applications. One or more dependent applications can be specified per
Dependnn value. Dependent applications are specified as a series of Words
in hexadecimal notation. Table 14 shows a typical Init registry entry using
dependencies.
HKEY_LOCAL_MACHINE\Init
Value Name
Value
Launch10
shell.exe
Launch20
device.exe
Launch30
gwes.exe
Depend30
hex:14,00
Launch50
taskman.exe
Depend50
hex:14,00, 1e,00
Table 156 a Typical Init Registry Entry Using Dependencies
In the preceding example, Gwes.exe is dependent on Device.exe starting and
Taskman.exe is dependent on Device.exe and Gwes.exe starting.
After Windows CE calls an application using the Init registry value, the
application must call the SignalStarted function.
SignalStarted indicates that the application is ready for the rest of the OS to
continue processing. The value that is passed as the parameter to
SignalStarted is the value passed on the command line of the application
started from the Init key
Korenix | Software Feature
26
“AutoRun.exe” Utility
If your applications have dependencies with other applications, use the
Remote Registry Editor to setup your applications manually. After finishing the
registry setup, run ―rFlush.exe‖ utility to flush the changed registry data to hive.
Otherwise, JetBox comes with an application launcher utility named
―AutoRun.exe‖ to complete the setup. Figure 6 shows the snapshot of
―AutoRun.exe‖ utility. Table 15 shows the description of user interfaces of
―AutoRun.exe‖ utility.
Figure 8 Snapshot of ―AutoRun.exe‖
Utility Name: AutoRun
User Interface
Description
File:
Specifies the application path.
…
Browses the application location.
Parameters:
Specifies the application arguments.
UP
Moves up the run order of selected application.
DN
Moves down the run order of selected
application.
WaitTime (ms):
The wait time in mini-seconds before running
application.
RunOnce
Runs the application only once on the next
boot.
Korenix | Software Feature
27
Utility Name: AutoRun
User Interface
Description
NOTE: There is a run flag attached with the
specified application, and the run flag will
be clear after the next boot.
New
Adds the specified application path into run list.
Modify
Updates the wait time or run once attributes of
the selected application.
Delete
Removes the selected application from run list.
Save & Exit
Saves run list information and exit.
NOTE: Run flags attached with the specified
applications will be set.
List Ctrl
Shows and Controls the run list information.
Table 167 Description of the User Interface of ―AutoRun.exe‖
3-3
Telnet Server
Overview
JetBox provides a Telnet server to allow remote administration through a
standard Telnet client. Using the Telnet server, the JetBox can be manipulated
as if it is running the command prompt on the device itself. The Telnet server is
also useful for device bring-up and debugging.
NOTE JetBox enables Telnet server without user authentication by
default.
Default Registry Settings
It’s necessary to be aware of the registry settings that impact security. The
Telnet server settings are located under the
HKEY_LOCAL_MACHINE\Comm\TELNETD registry key. Table 16 shows the
named values for the Telnet server registry key. The Telnet server reads the
values in the registry before servicing each request. Therefore, changes made
to the registry take affect immediately and do not require the Telnet server to
Korenix | Software Feature
28
be restarted.
HKEY_LOCAL_MACHINE\Comm\TELNETD
Value
Description
IsEnabled :
DWORD
To disable the Telnet server, set this value to
0; otherwise, set it to nonzero. If the Telnet
server is started and this value is not present,
this value defaults to accepting connections.
UseAuthenticatio
To require a password check on the user, set
n : DWORD
this value to 1; otherwise, set it to 0. By
default, the value 0 is set to disable the
authentication.
UserList : String
Provides a comma-separated list of allowed
users. Requires UseAuthentication to be
enabled. By default, the ―asterisk‖ or the ―at
sign‖ and the asterisk (* or @*) is set to allow
all users.
Table 178 Telnet Server Registry Key and Named Values
Security Notes
The security on the Telnet server is very light and vulnerable to security attacks.
Even if the Telnet server is configured to require password authentication, the
password is sent in plain text across the network and is therefore vulnerable to
packet sniffing. A malicious user could obtain the password to JetBox by
watching packets sent back and forth between the Telnet server and the client
during the authentication stage. If a malicious user could log on to JetBox, they
would have complete control over it. This could involve deleting or modifying
key system files and the registry.
Because of these serious security risks, it is strongly recommended you only
run the Telnet server for development and debugging purposes, on a
controlled, private network where you trust the users. It is strongly
recommended that you do not deploy this Telnet server on a public network
such as the Internet.
Recommendations
NOTE: Set the User List and Domain variables to prevent hacker attacks
Korenix | Software Feature
29
on your device
If Telnet server is used without appropriate values set for the User List and
Domain variables, your Telnet server will be vulnerable to hacker attacks.
These variables are not set by default. A hacker must only guess the device's
password, the way it is set in Control Panel, to obtain access to the server.
To prevent such an attack, the user name in the UserList registry value must
be set for each of the servers that are currently running. The user will then
need to log in with the specified user name and appropriate password to use
the server.
You can also set the domain variable in the DefaultDomain registry value,
which is located under the HKEY_LOCAL_MACHINE\Comm\Redir registry
key.
Refer with Section 3-2-2 User Manager Utility to learn how to add user
information to the local database if no domain controller is available in
the network.
3-4
FTP Server
Overview
JetBox implementation of FTP server enables you to transfer files from a
desktop computer using a TCP/IP connection. The implementation of FTP
server in JetBox is based on RFC 959. The included FTP server supports the
minimum implementation of the FTP protocol defined in RFC 959. This
minimum implementation includes configuration values, transfer parameters,
and ASCII and Image data types, and allows FTP to operate with a minimum of
error messages.
NOTE JetBox Enables FTP server by default.
Default Registry Settings
It’s necessary to be aware of the registry settings that impact security. The FTP
server settings are located under the HKEY_LOCAL_MACHINE\Comm\FTPD
Korenix | Software Feature
30
registry key. Table 17 shows the named values for the FTP server registry key.
HKEY_LOCAL_MACHINE\Comm\FTPD
Value
Description
AllowAnonymous :
DWORD
Default set to 1. Possible values are 0
(false) or 1 (true). Determines whether
the server will allow anonymous access.
AllowAnonymousUplo
Default set to zero (0). Possible values
ad : DWORD
are 0 (false) or 1 (true). Determines
whether authorization is required to
upload files to the server, delete files
from the server, and rename files.
AllowAnonymousVroo
ts : DWORD
Default set to zero (0). Possible values
are 0 (false) or 1 (true). Specifies
whether access to virtual roots is granted
or denied to anonymous users.
AllowLowPortValues :
DWORD
Default set to false (0). Possible values
are 0 (false) or 1 (true). If this value is set
to false, all PORT commands requesting
a port equal to or lesser than 1023 will be
rejected. If this key is set to true, low
ports will be allowed.
DefaultDir : String
Default root directory. Directory and
subdirectories of this key are accessible
remotely. If this value is not set in the
registry, the default is \Temp.
IsEnabled : DWORD
To disable the FTP server, set this value
to 0; otherwise, set it to nonzero. If the
FTP server is started and this value is
not present, This value is typically used
to keep the server disabled at boot time.
UseAuthentication :
DWORD
To require a password check on the
user, set this value to 1; otherwise, set it
to 0. By default, the value 0 is set to
disable the authentication.
UserList : String
Korenix | Software Feature
Provides a comma-separated list of
allowed users. Requires
31
HKEY_LOCAL_MACHINE\Comm\FTPD
Value
Description
UseAuthentication to be enabled. By
default, the ―asterisk‖ or the ―at sign‖ and
the asterisk (* or @*) is set to allow all
users.
Table 189 FTP Server Registry Key and Named Values
Security Notes
If AllowAnonymous is set to true, it will allow users to connect to the server
without providing verifiable credentials. Anyone can log in using the username
"anonymous" and any password to gain access. It is recommended that you
set this value to false and use the UserList registry setting to specify all
allowed users.
If AllowAnonymousUpload is set to true, unauthenticated users will be able
to copy files to, and delete files from, your server. This can be very dangerous
because attackers might upload dangerous applications and documents, or
they might delete important system files. It is not recommended to allow upload
permission for anonymous users.
If AllowAnonymousVroots is set to false, anonymous users will only be able
to access the main FTP share. If this value is set to true, unauthenticated users
will also be able to access VROOTs as well as the main share. Therefore you
should use this setting with caution.
Setting UseAuthentication to false enables clients to connect to the server
without providing credentials. It is therefore strongly recommended that you do
not set this value to false. Change this setting only if you have anonymous
clients that must access the server but cannot or will not send USER and
PASS credentials.
It is recommended that you set this value to a list of all users who should have
access to the server and its member VROOTs. Specifying the allowed users in
UserList and setting AllowAnonymous to false will help protect the device
from most attackers and keep your files available only to those users who need
to see them.
Recommendations
Korenix | Software Feature
32
NOTE: Set the User List and Domain variables to prevent hacker attacks
on your device
If the FTP Server functionality is used without appropriate values set for the
User List and Domain variables, the FTP server will be vulnerable to hacker
attacks. These variables are not set by default. A hacker must only guess the
device's password, the way it is set in Control Panel, to obtain access to the
server.
To prevent such an attack, the user name in the UserList registry value must
be set for each of the servers that are currently running. The user will then
need to log in with the specified user name and appropriate password to use
the server.
You can set the domain variable in the DefaultDomain registry value, which is
located under the HKEY_LOCAL_MACHINE\Comm\Redir registry key.
Setting the DefaultDomain registry value will require FTP clients to have valid
domain credentials to log in.
Refer with Section 3-2-2 User Manager Utility to learn how to add user
information to the local database if no domain controller is available in
the network.
3-5
Web Server
Overview
Web server facilitates the use of the Internet for communication between
JetBox and network printers, scanners, and other shared equipment. The Web
server applications send Hypertext Markup Language (HTML) pages to a
requesting browser. Users only need to have an Internet connection and a
browser to be able to make use of the Web server functionality. The Web
server supports IPv6 and also supports the use of Active Server Pages (ASP).
Default Registry Settings
Korenix | Software Feature
33
It’s necessary to be aware of the registry settings that impact security. The
Web server settings are located under the
HKEY_LOCAL_MACHINE\Comm\HTTPD registry key. If you make changes
to the Web server registry settings, it is necessary to stop the Web server and
restart it to make the changes take effect. The IsEnabled registry value is
checked only when the Web server is initially loaded. If the registry value is set
to zero (0), the Web server does not start. Changing this value to zero (0) while
the Web server is running has no effect. You also must stop the Web server to
make it stop accepting connections. Table 18 shows the named values for the
Web server registry key.
HKEY_LOCAL_MACHINE\Comm\HTTPD
Value
Description
BasicRealm :
STRING
Specifies the string that the Web server will
send to clients as its Basic realm when
performing basic authentication. If this
registry value is not set, the Web server will
default to using the string
"Microsoft-WinCE".
IsEnabled : DWORD If the value is not set in the registry, the Web
server is enabled. If the value is set to zero
(0), the Web server does not accept
connections from the network, even from
the local host.
Port : DWORD
Default setting is 80. This port receives
HTTP connections. Do not set the port to
zero (0).
Basic : DWORD
Default setting is zero (0). If this value is
nonzero, the Web server uses Basic
authentication for client connections.
NTLM : DWORD
Default setting is 1. If this value is set to
nonzero, the Web server uses NTLM
authentication for client browser
connections. Also, if this value is nonzero,
the failure of Basic authentication forces
NTLM authentication.
If the value is not set in the registry, NTLM is
Korenix | Software Feature
34
HKEY_LOCAL_MACHINE\Comm\HTTPD
Value
Description
not used.
DirBrowse :
DWORD
Default setting is zero (0). If this value is set
to nonzero, directory browsing is allowed. If
this value is not set in the registry, directory
browsing is turned off.
Filter DLLs : String
Default not set in the registry. List of DLL
names, separated by commas that
specifies the filters to use.
DefaultPage : String Default not set in the registry. If the value is
not present in the registry, the Web server
will use "default.htm;index.htm". List of
page names, separated by semicolons that
specifies file names interpreted by the Web
server to be default pages. When browsing
a directory, the Web server traverses this
list searching for a file of the same name in
the directory. If the file exists, it is sent to the
client. If no matching file exists, the Web
server sends a directory listing or returns an
error, depending on whether directory
browsing is enabled. If more than one
DefaultPage file name is matched, the
Web server uses the first matching file
name.
AdminUsers : String Default not set in the registry. List of user
names, separated by semicolons. A user
who has gained user access must be listed
in this key to gain Administrator access.
LogFileDirectory :
String
Default setting is "\windows\www" directory.
If the name is not set or if the specified
directory is inaccessible, no logging is
performed. Name of the directory where the
logging files are created.
PostReadSize :
DWORD
Korenix | Software Feature
If the value is not set in the registry,
PostReadSize will default to 48 KB. The
35
HKEY_LOCAL_MACHINE\Comm\HTTPD
Value
Description
Web server uses a minimum value of 8192
bytes (8 KB). If the value in the registry is
less than 8 KB, the value is ignored and the
Web server will use 8 KB.
Specifies the maximum number of bytes
that the Web server reads when receiving
POST data. To read more data, you must
use a raw data filter or call ReadClient in an
ISAPI extension.
MaxLogSize :
DWORD
Default setting is 32 KB. If this value is not
set in the registry, or if it is set to zero (0), no
logging is performed.
Maximum size, in bytes, that a log file can
become before it is rolled over.
MaxHeaderSize :
DWORD
Default setting is 48 KB in the registry.
Maximum number of bytes that the Web
server will read of HTTP headers. If the
header size exceeds this value, the Web
server will terminate the session and return
a message to the client: 400 - Bad Request.
MaxConnections :
DWORD
Default is not set in the registry. If the value
is not set in the registry, MaxConnections
will default to 10. Specifies the maximum
number of simultaneous connections to the
Web site. After the maximum number of
connections is established, additional client
requests will be sent a message: 503 –
Server Too Busy.
ServerID : String
Default is not set in the registry. If the value
is not set in the registry, ServerID will
default to "Microsoft-WinCE/X.Y", where X
is the major version and Y is the minor
version of Windows CE-based device. If
ServerID is set, the Web server returns the
specified server name in the response
Korenix | Software Feature
36
HKEY_LOCAL_MACHINE\Comm\HTTPD
Value
Description
header. Identifies the server name that is
included when the Web server generates
HTTP response headers. The response
header includes a field name "Server: ".
Optionally, you can include the software
version number or any similar information in
the string.
Table 20 Web Server Registry Key and Named Values
Security Notes
When using Basic authentication, the client browser sends the user identifier
and password to the server in clear text. In addition, all data sent between the
client and the browser is in clear text and therefore vulnerable to packet
sniffing. You should consider using SSL to help protect sensitive information.
Although the client browser sends the password to the server in encrypted
format, all data sent between the client and the browser is in clear text and
therefore vulnerable to packet sniffing. You should consider using SSL to help
protect sensitive information.
DirBrowse turns on the Web server's ability to provide local directory browsing.
This exposes the local file system to a remote browser through HTTP. Users
can view file lists and download files depending on virtual root and
authentication registry settings. Enabling directory browsing increases the
potential attack surfaces, therefore you should enable directory browsing only
when necessary.
User names in this list identify the administrators of the site who have access
to all virtual roots hosted on this Web site, including the restricted sites.
Choose these users carefully and ensure that they set proper password,
otherwise their accounts could be used to gain access to restricted sites.
Setting the value too small can block user access to the site. However, if the
value is too large the Web server will consume more system resources. Based
on your deployment model, choose this number appropriately.
To avoid revealing the server software information to malicious users, you may
want to create a custom server name that obfuscates the Web server and
operating system versions.
Korenix | Software Feature
37
Recommendations
A typical deployment uses a Web server in a private network to provide a
remote user interface to configure a headless device. The registry defines the
number of connections and when the MaxConnections registry value is not
set, the registry limits the number to 10.
A typical deployment uses the Web server to display status information or to
host a family or community Web site. You should not use the Web Server to
perform critical operations, such as machine control or financial processing.
Use NTLM and/or Basic authentication mechanism to limit access to known
users only. You can set the option in the
HKEY_LOCAL_MACHINE\COMM\HTTPD registry key.
SSL protocol helps to protect data from packet sniffing by anyone with physical
access to the network.
Carefully choose your virtual roots and limit access to the appropriate files by
providing appropriate user access lists. Anonymous users with access to the
virtual root may be able to access files and directories within that virtual root.
You can set the options in
HKEY_LOCAL_MACHINE\Comm\HTTPD\VROOTS registry key.
3-6
File Server
Overview
The File Server technology enables clients to access files and other resources,
such as printer, from a server over a network using TCP/IP. File Server uses
the Common Internet File System (CIFS). This is an extension of the Server
Message Block (SMB) file sharing protocol. CIFS enables a network-enabled
application to access and manipulate files and directories on a remote server
in the same way that it the application accesses and manipulates files and
directories on the local system.
Default Registry Settings
The registry stores information necessary to configure the system for
Korenix | Software Feature
38
applications and hardware devices. The registry also contains information that
the operating system continually references during operation. JetBox
enables you to create virtual file server directories. To users who access your
file server share, virtual directories appear as subdirectories of the file server
share, although these directories may be located in a different folder. You can
create a virtual root directory called "myCF" by specifying the following registry
key: HKEY_LOCAL_MACHINE\Services\SMBServer\Shares\Hard Disk.
Note the maximum length of the virtual root directory is 12 characters.
Table 19 shows the named values for the
HKEY_LOCAL_MACHINE\Services\SMBServer\Shares registry key.
HKEY_LOCAL_MACHINE\Services\SMBserver\Shares
Value
Description
UseAuthenticatio
n : DWORD
No default set. Setting this value to 0 will
disable the authentication on the file server.
The file server will be accessible to all users
on the network.
Table 21 Named Values of HKEY_LOCAL_MACHINE\Services\SMBServer\Shares Key.
Table 20 shows the named values that are stored under the virtual root key. An
example of such a virtual root key is
HKEY_LOCAL_MACHINE\Services\SMBServer\Shares
HKEY_LOCAL_MACHINE\Services\SMBserver\Shares
Value
Description
Path :
String
Specifies the path to be shared.
Type :
DWORD
Setting this value to 1 designates this as a print
server share, setting this value to 0 (zero) designates
this as a file server share.
UserList :
String
Specifies a comma-separated list of allowed users.
Table 22 Named Values of HKEY_LOCAL_MACHINE\Services\SMBServer\Shares\Hard Disk
Key
Security Notes
Korenix | Software Feature
39
It is not recommended that you disable authentication on the file server and
you share the \Windows or root directory.
You can specify a list of folders that cannot be shared. You can use any name
for each folder you specify in the exclusion list. Setting the
HKEY_LOCAL_MACHINE\Services\Smbserver\Shares\ExcludePaths
registry key prevents the configuration functions from creating the specified
shares, so that they cannot be accessed by an un-trusted application. Table 21
shows an example how to exclude the \Windows and \Documents and Settings
directories:
HKEY_LOCAL_MACHINE\Services\Smbserver\Shares\ExcludePaths
Value Name
Value
―Windows‖
―\\Windows‖
―My Documents‖
―\\Documents and Settings‖
Table 23 an Example to Exclude the Folders to be Shared
Recommendations
After you have configured your share folders by editing the registry manually or
using the remote configuration tool, you can access and browse the folders
you created in the following steps.
1. On the development workstation, from the Start menu, chooses Run.
In the Open box, type \\JetBox<model name> (for example: \\JetBox8152),
and then choose OK. The Connect to JetBox dialog box appears.
2. In the Connect to JetBox dialog box, type the user name you created and
the corresponding password, and then choose OK. A window appears that
shows the two root directories you created.
3. You can now browse the folders you created and access specific files in
these folders.
The net use command can also to be used in the DOS command prompt tool,
and Figure 7 shows how to map the myCF folder of JetBox to a drive x: in your
development workstation,
Korenix | Software Feature
40
Figure 9 Snapshot of Share a Folder via ―net use‖ Command
Chapter 4 Web-based Administration
4-1
Overview
JetBox can also run without displays (think an industrial controller or a protocol
gateway). In this case, a web server running on JetBox itself can dynamically
generate HTML and send it back to a remote web browser, which in turn can
configure the device remotely.
4-2
Remote Administration Page
(RemoteAdmin)
4-2-1 Introduction
The Remote Configuration (RemoteAdmin) page for the Web Server enables
Korenix | Web-based Administration
41
you to remotely administer JetBox using your Web browser. The functionality
of the RemoteAdmin includes a wizard that assists users with the initial JetBox
setup and other common tasks. Use your Internet browser and go to
http://<JetBox IP Address> to launch RemoteAdmin.
Note the RemoteAdmin page is set as the default home page of JetBox.
4-2-2 First use Setup Wizard
On first use, the application requires a password. In addition, the application
requires authentication—you must use the default username ADMIN and the
same password that you typed on first use. Figure 8 to Figure 12 shows the
steps to finish the first use setup wizard.
Figure 4 First Use Setup Wizard
Korenix | Web-based Administration
42
Figure 5 Input Password and Re-type to Confirm
Figure 6 Choose ―I do not want to setup an Internet connection now‖
Korenix | Web-based Administration
43
Figure 7 JetBox is resetting
Figure 8 Authentication for Remote Configuration
4-2-3 RemoteAdmin Home Page
JetBox remote administration page also provides support for user tasks such
as configuring user and share and security settings. Additionally, the UI
provides advanced gateway features, such as port forwarding. Table 22 shows
the description of the user interface of the RemoteAdmin Home page. Figure
13 is the snapshot of the RemoteAdmin home page.
Page Name: Home
User Interface
Description
Wide Area Network
(WAN) settings
Displays a summary of the WAN network
settings.
Korenix | Web-based Administration
44
Release
Releases the dynamically assigned IP
address on the WAN network.
Renew
Obtains a new IP address on the WAN
network.
Local Area Network
(LAN) settings
Displays a summary of the LAN network
settings.
DHCP client List
Displays the clients on the LAN network.
Table 19 Description of the User Interface of the Reset Base
Figure 9 Snapshot of the RemoteAdmin Home Page
Korenix | Web-based Administration
45
4-2-4 Device Management Pages
4-2-4-1 Reset Base Station Page
Table 23 shows the description of the user interface of the Reset Base Station
page. Figure 14 to Figure 16 shows the steps to reset the JetBox.
Page Name: Reset Base Station
User Interface
Description
Reset
Reset the JetBox (Gateway).
Table 20 Description of the User Interface of the Reset Base Station Page
Figure 10 Click the Reset Button
Korenix | Web-based Administration
46
Figure 11 Click ―OK‖ to Confirm
Figure 12 JetBox is Resetting
4-2-4-2 Set Time Page
Table 24 shows the description of the user interface of the Set Time page.
Figure 17 and Figure 18 show the snapshots of the Set Time page.
Page Name: Set Time
User Interface
Description
Time synchronization
method
Options for time synchronization:
Internet time server
Specifies the time server name.
Set time manually
Specifies the time settings.
Synchronize to Internet time server or
Set time manually.
Base station time zone Sets time zone.
Apply
Applies the settings.
Cancel
Cancels the settings.
Table 21 Description of the User Interface of the Set Time Page
Korenix | Web-based Administration
47
Figure 13 Snapshot of the Set Time Pae for Synchronize to Internet Time Server
Figure 14 Snapshot of the Set Time Page for Set Time Manually
Korenix | Web-based Administration
48
4-2-4-3 Application Port Forwarding Page
Table 25 shows the description of the user interface of the Application Port
Forwarding page. Figure 19 shows the snapshot of the Application Port
Forwarding page. Note Add, Enable, Edit, Delete will cause the related
services been reset.
Page Name: Application Port Forwarding
User Interface
Description
Description
Description of the port forwarding
settings.
Outbound port
Specifies outbound port number.
Trigger protocol
Specifies the trigger protocol.
Inbound TCP ports
Specifies inbound TCP port numbers.
Inbound UDP ports
.Specifies outbound UDP port numbers.
Add
Adds the current settings.
Clear
Clears the current settings
Enable
Enables the specified settings.
Edit
Edits the specified settings.
Delete
Deletes the specified settings.
Table 22 Description of the User Interface of the Application Port Forwarding Page
Figure 15 Snapshot of the Application Port Forwarding Page
Korenix | Web-based Administration
49
4-2-4-4 Back Up/ Restoring Settings Page
Table 26 shows the description of the user interface of the Back Up/Restoring
Settings page. Figure 20 shows the snapshot of the Back Up/Restoring
Settings page. Figure 21 shows the snapshot of download the back up settings
file.
Page Name: Back Up/Restoring Settings
User Interface
Description
Back Up Settings
Back ups the current settings to a file.
Browse…
Browses and selects a back up settings
file.
Restore Settings
Restores the settings from a file.
Table 23 Description of the User Interface of the Back Up/ Restoring Settings Page
Figure 16 Snapshot of the Back Up/ Restoring Settings Page.
Korenix | Web-based Administration
50
Figure 17 Snapshot of Download the Back Up Settings File.
4-3
Web Administration Page (WebAdmin)
4-3-1 Introduction
The Web Server Administration (WebAdmin) page for the Web server enables
you to remotely administer your Web server using your Web browser. Use
WebAdmin to manage the accessibility, security, and file sharing features of
your Web server. Include configure which files are shared and how they are
accessed and which users have access to which files, and the authentication
protocols the Web server will use and configure the Web server log. Use your
Internet browser and go to http://<JetBox IP Address>/WebAdmin to launch
WebAdmin. Refer with Section 4-3-3 Instructions Page for details before
starting configuring the Web server.
4-3-2 WebAdmin Home Page
Table 27 is the description of the user interface of the Home page. Figure 22
and Figure 23 show the snapshots of the home page of the Web server
administration page.
Korenix | Web-based Administration
51
Page Name: Home
User Interface
Description
Help topics
For more information about WebAdmin.
Configuring Web Sites
For more information about configuring
Web sites.
Default Web Site:
Modify
Modifies the default Web site.
Public Web Site:
Modifies the public Web site.
Modify
Public Web Site:
Delete
Deletes the public Web site.
CreateNew
Creates a new Web site.
Table 24 Description of the User Interface of the WebAdmin Home Page
Figure 18 Snapshot of the WebAdmin Home Page
Korenix | Web-based Administration
52
Figure 19 Snapshot of the WebAdmin Home Page
4-3-3 Instructions Page
Figure 24 shows the snapshot of the Instructions page. The Help topics
provide information about configuring, securing, and managing the Web server
on your JetBox device.
Korenix | Web-based Administration
53
Figure 20 Snapshot of the Instructions Page
4-3-4 Logging Page
Table 28 is the description of the user interface of the Logging page. Figure 25
shows the snapshot of the Logging page. Figure 26 shows the snapshot of the
current log file.
Page Name: Logging
User Interface
Description
Here
For more information about Logging.
View the Current Web
server log file
Views the current Web server log file..
Log File Location:
Specifies the log file location.
Korenix | Web-based Administration
54
Maximum Log File
Size:
Specifies the maximum log file size in
bytes.
Update Settings
Updates the settings.
Table 25 Description of the User Interface of the Logging Page
Figure 21 Snapshot of the Current Logging Page
Korenix | Web-based Administration
55
Figure 22 Snapshot of the Log File
4-3-5 SSL Configuration Page
Table 29 is the description of the user interface of the SSL Configuration page.
Figure 27 shows the snapshot of the SSL Configuration page.
Page Name: SSL Configuration
User Interface
Description
Here
For more information about SSL
Configuration.
Enable SSL:
Enables SSL on initialization of Web
server.
Server Certificate
Subject Line:
Specifies the server certificate subject
line.
Update
Updates the settings.
Table 26 Description of the User Interface of the SSL Configuration Page
Korenix | Web-based Administration
56
Figure 23 Snapshot of the SSL Configuration Page
4-3-6 Restart Web Server Page
Figure 28 shows the snapshot of the Restart Web Server page.
Figure 24 Snapshot of the Restart Web Server Page
Korenix | Web-based Administration
57
4-4
System Administration Page (SysAdmin)
4-4-1 Introduction
The System Administration (SysAdmin) page for the JetBox Web Server
enables you to remotely administer JetBox using your Web browser. Use
SysAdmin to manage the processes, files and registry of JetBox. Include
launch/kill a process, upload/download a file, create/remove a directory and
edit the registry. Use your Internet browser and go to http://<JetBox IP
Address>/SysAdmin to launch SysAdmin.
Note the SysAdmin is discontinued in Windows CE 6.0.
4-4-2 SysAdmin Home Page
Figure 29 shows the snapshot of the home page of the System administration
page. Choose one Web Browser you are using. Figure 30 shows the snapshot
of the home page of the System administration page with framing UI.
Figure 25 Snapshot of the SysAdmin Home Page
Korenix | Web-based Administration
58
Figure 26 Snapshot of the SysAdmin Home Page
4-4-3 System Tools Page
System Info Page
Table 30 is the description of the user interface of the System Info page.
Figure 31 is the snapshot of the System Info page. It shows the system
information, includes version, number of processors, the CPU architecture, the
memory and data store size, the network adapters and the system time.
Page Name: System Info
User Interface
Description
Refresh
Refreshes the current page
Table 27 Description of the User Interface of the System Info Page
Korenix | Web-based Administration
59
Figure 27 Snapshot of the System Info Page
Processes Page
Table 31 is the description of the user interface of the Processes page. Figure 32 is
the snapshot of the Processes page.
Page Name: Processes
User Interface
Description
Refresh
Refreshes the current page.
Launch processes:
Specifies the executable file path.
Execute
Launches the specified executable file.
PID
Specifies the process ID.
Process Name
Specifies the process name.
Kill
Kills the process.
Table 28 Description of the User Interface of the Processes Page
Korenix | Web-based Administration
60
Figure 28 Snapshot of the Processes Page
4-4-4 File Browser Page
Table 32 is the description of the user interface of the File Browser page.
Figure 33 is the snapshot of the File Browser page.
Note you may consider looking at the SMB server to do upload and
download as it will be way faster and probably a better user experience
since it'll look like a remote file share.
Page Name: File Browser
User Interface
Description
Refresh
Refreshes the working directory.
Directory Tree View
Selects the working directory.
JetBox
Indicates the working directory.
Upload File:
Specifies the upload file path.
Browse…
Browses and selects the upload file.
Upload
Uploads the specified file.
Copy to:
Specifies the copy to file path.
New Directory Name: Specifies the new directory name.
Korenix | Web-based Administration
61
Page Name: File Browser
User Interface
Description
Create Directory
Creates a new directory under working
directory.
Remove Directory
Removes the working directory.
Delete
Deletes the specified file.
Copy
Copies the specified file to the specified
copy to path.
File Name
Downloads the specified file.
Table 29 Description of the User Interface of the File Browser Page
Figure 29 Snapshot of the File Browser Page
4-4-5 Registry Editor Page
Table 33 is the description of the user interface of the Registry Editor page.
Figure 34 is the snapshot of the Registry Editor page.
Korenix | Web-based Administration
62
Page Name: File Browser
User Interface
Description
Refresh
Refreshes the current key.
Registry Key Tree View
Selects the working registry key.
HKEY_LOCAL_MACHINE
Indicates the working registry key.
New Value Name:
Specifies the new value name.
New value Type:
Specifies the new value type.
New Value
Creates a new value.
Modified Value:
Specifies the modified value data.
New Subkey Name:
Specified the new registry key.
Create Key
Create a new registry key.
Delete Key
Deletes the working registry key.
Delete
Deletes the specified value.
Modify
Modifies the value with specified
modified value.
Table 30 Description of the User Interface of the Registry Editor Page
Figure 30 Snapshot of the Registry Editor Page
Korenix | Web-based Administration
63
Chapter 5 Connectivity Features
5-1
Overview
Microsoft® Windows® CE provides tools for testing and debugging a Windows
CE–based device. Most tools for debugging and testing reside on the
development workstation, and thus rely on a connectivity infrastructure that
facilitates communication between the development workstation and a target
device. Platform Manager supports application connectivity. Application
connectivity is a communications framework that allows you to establish a
connection between an application running on a development workstation and
a target device. Remote Tools and eMbedded Visual C++ use the application
connectivity support in Platform Manager to connect to a target device.
5-2
ActiveSync Connection
5-2-1 Introduction
ActiveSync allows you to create a synchronization relationship between your
mobile device and PC using a cable, cradle, Bluetooth, or infrared connection.
ActiveSync can also make it possible for your device to connect to other
resources through your PC. It’s recommended to setup an ActiveSync
connection during developing your application with Microsoft eVC++4.0 or
Visual Studio 2005. You can use a serial cable to connect JetBox to your PC.
Note: Setup up Microsoft ActiveSync 4.5 or above before connecting the
JetBox with your PC. Microsoft ActiveSync 4.5 can be downloaded from
the following link:
http://www.microsoft.com/windowsmobile/activesync/activesync45.msp
x
Korenix | Connectivity Features
64
5-2-2 Connection via COM port
An alternative way to setup an ActiveSync connection with JetBox is using the
RS232 port. Figure 35 to Figure 45 show the CE side procedures to establish
an ActiveSync connection via RS232. Figure 46 to Figure 52 show the PC side
procedures to establish an ActiveSync connection via RS232.
Note: JetBox configure the default PC connection as USB, so it’s
necessary to change the PC connection before establish ActiveSync
connection via RS232.
Figure 31 Launch ―Network and Dial-up Connections‖ Control Applet
Korenix | Connectivity Features
65
Figure 32 Make New Connection
Figure 33 Choose ―Direct Connection‖ Option
Korenix | Connectivity Features
66
Figure 34 Choose a RS232 COM Port
Figure 35 Configure the Selected COM Port
Korenix | Connectivity Features
67
Figure 36 Set Flow Control as None
Figure 37 Make ―My Connection‖ Is Completed
Korenix | Connectivity Features
68
Figure 38 Launch ―PC Connection‖ Control Applet
Figure 39 Select ―Change…‖ to Change PC Connection
Korenix | Connectivity Features
69
Figure 40 Change PC Connection to ―My Connection‖
Figure 41 Change PC Connection Is Completed
Korenix | Connectivity Features
70
Figure 42 Configure ActiveSync Connection Settings
Figure 43 Allow Connections to COM1
Figure 44 ActiveSync Is Not Connected
Korenix | Connectivity Features
71
Figure 45 Connect JetBox with PC via RS232 Null Modem Cable
Figure 46 Choose ―No‖ to Skip Setup a Partnership
Figure 47 ActiveSync Is Connected
Figure 48 ActiveSync Is Connected
Korenix | Connectivity Features
72
5-2-3 Explore JetBox
After ActiveSync connection has been established, click the Explore button to
explore JetBox. Figure 53 shows a connected Microsoft ActiveSync window.
Figure 54 shows a snapshot of exploring JetBox via ActiveSync. It’s
recommended to exchange the application data with JetBox via
ActiveSync connection during developing your applications.
Figure 49 Microsoft ActiveSync
Figure 50 Explore the JetBox via ActiveSync
Korenix | Connectivity Features
73
5-3
Manual Server Connection
5-3-1 Overview
If ActiveSync connectivity is not available, a Manual Server connection should
be possible. Manual Server uses TCP/IP communications between host PC
and device and supports most of the functions of ActiveSync. It does not
support file or outlook synchronization and takes more steps to initiate.
Both ActiveSync and Manual Server are used by the Platform Manager
component of eVC++. Platform Manager provides communication support for
application debugging and add-on tools. You may need to install Microsoft
eVC++ 4.0 before establishing a manual server connection with JetBox.
5-3-2 Configure Platform Manager
Figure 55 to Figure 59 show how to establish a manual server connection on a
Default Device.
Figure 51 Configure Platform Manager
Korenix | Connectivity Features
74
Figure 52 Setup the Properties of the Default Device
Figure 53 Select ―TCP/IP Transport for Windows CE‖ for Transport
Korenix | Connectivity Features
75
Figure 54 Select ―Manual Server‖ for Startup Server, then Click Test
Figure 55 Manual Server - Action
5-3-3 Telnet with JetBox
It’s recommended to Telnet with JetBox and launch CEMGRC.EXE remotely.
Figure 60 and Figure 61 show how to identify the IP address of JetBox. Figure
62 and Figure 63 show how to start a telnet session to JetBox from your PC.
Figure 64 shows launch Manual Server – Action command on JetBox. Figure
Korenix | Connectivity Features
76
65 shows success to establish the Manual Server connection
Figure 56 Double Click the Network Icon
Figure 57 IP address of the DM9CE1 Network Adapter
Figure 58 Start a Telnet Session to JetBox
Figure 59 Success to Telnet JetBox
Korenix | Connectivity Features
77
Figure 60 Launch ―Manual Server – Action‖ Command
Figure 61 Success to Establish the Manual Server Connection
5-3-4 Remote Tools via Manual Server Connection
Figure 66 to Figure 70 show the procedures to launch a remote tool via manual
server connection.
Korenix | Connectivity Features
78
Figure 62 Launch Remote Zoom in Tool
Figure 63 Select Default Device
Korenix | Connectivity Features
79
Figure 64 Manual Server - Action
Figure 65 Launch ―Manual Server – Action‖ Command
Figure 66 Success to Launch Remote Zoomin
Korenix | Connectivity Features
80
Chapter 6 Application Development
6-1
Overview
You can import JetBox SDK eMbedded Visual C++ 4.0 or Visual Studio .NET
2003. An application developer can then use the SDK to create applications
that run on JetBox run-time image.
6-2
Install JetBox SDK
Figure 71 to Figure 80 show the procedures of setup JetBox SDK. It use
JetBox8100 photos as an example.
Figure 67 Launch JetBox SDK Setup file to Start Installing SDK
Korenix | Application Development
81
Figure 68 JetBox SDK Setup Wizard
Figure 69 Accept End-User License Agreement
Korenix | Application Development
82
Figure 70 Enter Customer information
Figure 71 Choose ―Complete‖ Setup Type
Korenix | Application Development
83
Figure 72 Choose the Destination Folder
Figure 73 Ready to Install
Korenix | Application Development
84
Figure 74 Install JetBox SDK
Figure 75 Completing JetBox SDK Setup Wizard
Korenix | Application Development
85
6-3
Hello Word Application with eVC++ 4.0
Figure 80 to Figure 88 show the procedures of developing a ―Hello World‖
application with Microsoft Embedded Visual C++ 4.0. Figure 89 to Figure 90
show the procedures of executing a ―Hello World‖ application with Microsoft
Embedded Visual C++ 4.0.
Note it’s necessary to establish a connection between JetBox with your
PC before downloading and executing the application from eVC++4.0.
Figure 76 New a Project with eVC++4.0
Korenix | Application Development
86
Figure 77 Hello World Application with Win32 (WCE x86)
Figure 78 a typical ―Hello World!‖ Application
Korenix | Application Development
87
Figure 79 Complete to Create the ―Hello World‖ Project
Figure 80 Select the Active Configuration for Customized WCE OS Devices
Korenix | Application Development
88
Figure 81 Rebuild Active Project and All Project Dependencies
Figure 82 Connecting to the JetBox
Figure 83 Downloading Hello World Application to JetBox
Korenix | Application Development
89
Figure 84 Finish Downloading Hello World Application to JetBox
Figure 85 Execute Hello World Application
Korenix | Application Development
90
Figure 86 Snapshot of the Hello World Application
Korenix | Application Development
91
6-4
Hello World Application with VS2005
Figure 91 to Figure 101 show the procedures of developing a ―Hello World‖
application with Microsoft Visual Studio 2005.
Figure 87 New an Application Project with VS2005
Korenix | Application Development
92
Figure 88 Create a Hello World Application for Windows CE 5.0 Smart Device Using Visual C#
Figure 89 Edit the Appearance Text to Hello World!
Korenix | Application Development
93
Figure 90 Configure the Target Device as Windows CE 5.0 Device
Figure 91 Connect to Device
Korenix | Application Development
94
Figure 92 Connect to Windows CE 5.0 Device Successded
Figure 93 Rebuild Solution
Figure 94 Start Debugging
Korenix | Application Development
95
Figure 95 Deploy Hello World Application to Windows CE 5.0 Device
Figure 96 Hello World (Running)
Figure 97 Snapshot of the Hello World Application on JetBox
Korenix | Application Development
96
Chapter 7 Appendix
7-1
Table List
Table 1 Application – End User .......................................................... 7
Table 2 Applications and Services Development ............................... 9
Table 3 Communication Service and Networking ............................ 13
Table 4 Core OS Service ................................................................. 14
Table 5 Device Management ........................................................... 14
Table 6 File System and Data Store................................................. 15
Table 7 Graphics and Multimedia Technologies ............................... 16
Table 8 Security ............................................................................... 17
Table 9 Shell and User Interface ...................................................... 18
Table 10 Platform Manager .............................................................. 18
Table 11 Description of the Usr Interface of ―SerPerf‖...................... 21
Table 12 Arguments Description of ―UsrMgr.exe‖ ............................ 24
Table 13 Named Values of HKEY_LOCAL_MACHINE\Init Key ....... 26
Table 14 a Typical Init Registry Entry Using Dependencies ............. 26
Table 15 Description of the User Interface of ―AutoRun.exe‖ ........... 28
Table 16 Telnet Server Registry Key and Named Values ................. 29
Table 17 FTP Server Registry Key and Named Values ................... 32
Table 18 Web Server Registry Key and Named Values ................... 37
Table 19 Named Values of
HKEY_LOCAL_MACHINE\Services\SMBServer\Shares Key. . 39
Table 20 Named Values of
HKEY_LOCAL_MACHINE\Services\SMBServer\Shares\Hard
Disk Key ................................................................................... 39
Table 21 an Example to Exclude the Folders to be Shared ............. 40
Table 22 Description of the User Interface of the Reset Base ......... 45
Table 23 Description of the User Interface of the Reset Base Station
Page ......................................................................................... 46
Table 24 Description of the User Interface of the Set Time Page .... 47
Table 25 Description of the User Interface of the Application Port
Korenix | Appendix
97
Forwarding Page ...................................................................... 49
Table 26 Description of the User Interface of the Back Up/ Restoring
Settings Page ........................................................................... 50
Table 27 Description of the User Interface of the WebAdmin Home
Page ......................................................................................... 52
Table 28 Description of the User Interface of the Logging Page ...... 55
Table 29 Description of the User Interface of the SSL Configuration
Page ......................................................................................... 56
Table 30 Description of the User Interface of the System Info Page 59
Table 31 Description of the User Interface of the Processes Page .. 60
Table 32 Description of the User Interface of the File Browser Page
................................................................................................. 62
Table 33 Description of the User Interface of the Registry Editor Page
................................................................................................. 63
7-2
Figure List
Figure 1 Snapshot of the Control Panel of JetBox ........................... 19
Figure 2 Configuration Snapshot of ―SerPerf‖ Control Applet .......... 20
Figure 3 Run Time Snapshot of ―SerPerf‖ Control Applet ................ 20
Figure 4 Snapshot of ―UsrMgr.exe‖ .................................................. 24
Figure 5 Snapshot of ―rFlush.exe‖ ................................................... 25
Figure 6 Snapshot of ―AutoRun.exe‖ ............................................... 27
Figure 7 Snapshot of Share a Folder via ―net use‖ Command ......... 41
Figure 8 First Use Setup Wizard ...................................................... 42
Figure 9 Input Password and Re-type to Confirm ............................ 43
Figure 10 Choose ―I do not want to setup an Internet connection now‖
................................................................................................. 43
Figure 11 JetBox is resetting ........................................................... 44
Figure 12 Authentication for Remote Configuration ......................... 44
Figure 13 Snapshot of the RemoteAdmin Home Page .................... 45
Figure 14 Click the Reset Button ..................................................... 46
Figure 15 Click ―OK‖ to Confirm ....................................................... 47
Figure 16 JetBox is Resetting .......................................................... 47
Figure 17 Snapshot of the Set Time Pae for Synchronize to Internet
Time Server .............................................................................. 48
Korenix | Appendix
98
Figure 18 Snapshot of the Set Time Page for Set Time Manually ... 48
Figure 19 Snapshot of the Application Port Forwarding Page ......... 49
Figure 20 Snapshot of the Back Up/ Restoring Settings Page. ....... 50
Figure 21 Snapshot of Download the Back Up Settings File. .......... 51
Figure 22 Snapshot of the WebAdmin Home Page ......................... 52
Figure 23 Snapshot of the WebAdmin Home Page ......................... 53
Figure 24 Snapshot of the Instructions Page ................................... 54
Figure 25 Snapshot of the Current Logging Page............................ 55
Figure 26 Snapshot of the Log File .................................................. 56
Figure 27 Snapshot of the SSL Configuration Page ........................ 57
Figure 28 Snapshot of the Restart Web Server Page ...................... 57
Figure 29 Snapshot of the SysAdmin Home Page........................... 58
Figure 30 Snapshot of the SysAdmin Home Page........................... 59
Figure 31 Snapshot of the System Info Page .................................. 60
Figure 32 Snapshot of the Processes Page .................................... 61
Figure 33 Snapshot of the File Browser Page ................................. 62
Figure 34 Snapshot of the Registry Editor Page .............................. 63
Figure 35 Launch ―Network and Dial-up Connections‖ Control Applet
................................................................................................. 65
Figure 36 Make New Connection .................................................... 66
Figure 37 Choose ―Direct Connection‖ Option ................................. 66
Figure 38 Choose a RS232 COM Port ............................................ 67
Figure 39 Configure the Selected COM Port ................................... 67
Figure 40 Set Flow Control as None ................................................ 68
Figure 41 Make ―My Connection‖ Is Completed .............................. 68
Figure 42 Launch ―PC Connection‖ Control Applet .......................... 69
Figure 43 Select ―Change…‖ to Change PC Connection................. 69
Figure 44 Change PC Connection to ―My Connection‖ .................... 70
Figure 45 Change PC Connection Is Completed ............................. 70
Figure 46 Configure ActiveSync Connection Settings ..................... 71
Figure 47 Allow Connections to COM1 ............................................ 71
Figure 48 ActiveSync Is Not Connected .......................................... 71
Figure 49 Connect JetBox with PC via RS232 Null Modem Cable .. 72
Figure 50 Choose ―No‖ to Skip Setup a Partnership ........................ 72
Figure 51 ActiveSync Is Connected ................................................. 72
Figure 52 ActiveSync Is Connected ................................................. 72
Figure 53 Microsoft ActiveSync........................................................ 73
Korenix | Appendix
99
Figure 54 Explore the JetBox via ActiveSync .................................. 73
Figure 55 Configure Platform Manager............................................ 74
Figure 56 Setup the Properties of the Default Device ...................... 75
Figure 57 Select ―TCP/IP Transport for Windows CE‖ for Transport 75
Figure 58 Select ―Manual Server‖ for Startup Server, then Click Test
................................................................................................. 76
Figure 59 Manual Server - Action .................................................... 76
Figure 60 Double Click the Network Icon......................................... 77
Figure 61 IP address of the DM9CE1 Network Adapter ................... 77
Figure 62 Start a Telnet Session to JetBox ...................................... 77
Figure 63 Success to Telnet JetBox................................................. 77
Figure 64 Launch ―Manual Server – Action‖ Command ................... 78
Figure 65 Success to Establish the Manual Server Connection ...... 78
Figure 66 Launch Remote Zoom in Tool .......................................... 79
Figure 67 Select Default Device ...................................................... 79
Figure 68 Manual Server - Action .................................................... 80
Figure 69 Launch ―Manual Server – Action‖ Command ................... 80
Figure 70 Success to Launch Remote Zoomin ................................ 80
Figure 71 Launch JetBox SDK Setup file to Start Installing SDK ..... 81
Figure 72 JetBox SDK Setup Wizard ............................................... 82
Figure 73 Accept End-User License Agreement .............................. 82
Figure 74 Enter Customer information ............................................. 83
Figure 75 Choose ―Complete‖ Setup Type ...................................... 83
Figure 76 Choose the Destination Folder ........................................ 84
Figure 77 Ready to Install ................................................................ 84
Figure 78 Install JetBox SDK ........................................................... 85
Figure 79 Completing JetBox SDK Setup Wizard ............................ 85
Figure 80 New a Project with eVC++4.0 .......................................... 86
Figure 81 Hello World Application with Win32 (WCE x86) ............... 87
Figure 82 a typical ―Hello World!‖ Application .................................. 87
Figure 83 Complete to Create the ―Hello World‖ Project .................. 88
Figure 84 Select the Active Configuration for Customized WCE OS
Devices ..................................................................................... 88
Figure 85 Rebuild Active Project and All Project Dependencies ...... 89
Figure 86 Connecting to the JetBox ................................................ 89
Figure 87 Downloading Hello World Application to JetBox .............. 89
Figure 88 Finish Downloading Hello World Application to JetBox .... 90
Korenix | Appendix
100
Figure 89 Execute Hello World Application ...................................... 90
Figure 90 Snapshot of the Hello World Application .......................... 91
Figure 91 New an Application Project with VS2005 ......................... 92
Figure 92 Create a Hello World Application for Windows CE 5.0
Smart Device Using Visual C#.................................................. 93
Figure 93 Edit the Appearance Text to Hello World! ........................ 93
Figure 94 Configure the Target Device as Windows CE 5.0 Device 94
Figure 95 Connect to Device ........................................................... 94
Figure 96 Connect to Windows CE 5.0 Device Successded ........... 95
Figure 97 Rebuild Solution .............................................................. 95
Figure 98 Start Debugging ............................................................... 95
Figure 99 Deploy Hello World Application to Windows CE 5.0 Device
................................................................................................. 96
Figure 100 Hello World (Running) ................................................... 96
Figure 101 Snapshot of the Hello World Application on JetBox ....... 96
7-3
Revision History
V0.2
by 2011/4/8
1. Add utility for version check: version utility, canver utility
V0.1
by 2011/ 3/ 30
7-4
Customer Service
Korenix Technologies Co., Ltd.
Business service: [email protected]
Customer service: [email protected]
Korenix | Appendix
101

advertisement

Key Features

  • Web Server
  • FTP Server
  • Telnet Server
  • Serial Ports
  • Ethernet Port
  • Device Management
  • Remote Administration

Frequently Answers and Questions

What is the JetBox 8152?
The JetBox 8152 is a small footprint device with built-in Ethernet port and serial ports. It can be used for applications that require a small footprint, such as industrial controllers, communications hubs, and point-of-sale terminals.
How do I manage the JetBox 8152 remotely?
The JetBox 8152 can be managed remotely using its built-in web server, FTP server, and Telnet server.
What are some of the key features of the JetBox 8152?
Some of the key features of the JetBox 8152 include its web server, FTP server, Telnet server, serial ports, Ethernet port, and device management capabilities.

Related manuals

Download PDF

advertisement