2010 Legacy Whirlpool Owner's Manual

2010 Legacy Whirlpool Owner's Manual
OWNER’S MANUAL
MASTER SPAS LEGACY OWNER’S MANUAL
Welcome To Ultimate Relaxation!
Thank you for choosing your new spa built by Master Spas. Please read the
entire Owner’s Manual before installing and using your spa. The goal of this
manual is to provide you with safety and operational information plus some tips
that will help you enjoy your spa to its fullest.
At the time of print, this manual is accurate in its information. Master Spas
reserves the right to change or improve its product without prior notice.
To check on updates or for other information, please visit www.masterspas.com
and follow the links to the customer service section.
Record Of Ownership
Name����������������������������������������������������������������������
Address��������������������������������������������������������������������
City _____________________________________ State __________ Zip���������������
Date Purchased ______ /______ /_______
Model ______________________________ Serial # �������������������������������
Dealer Name ���������������������������������������������������������������
Phone # (______)________-__________
Service Tech Rep������������������������������������������������������������
*Serial Number Location
The serial number for your spa is located in the filter area, on the spa system
pack, or on the listing plate on the skirting. It is a six digit number. Ex. 104590
6927 Lincoln Parkway
Fort Wayne, Indiana 46804
800-860-7727 • www.masterspas.com
1
TABLE OF CONTENTS
Safety Instructions������������������������������������������������������������������������������������������������� 3-10
Glossary of Spa Terminology������������������������������������������������������������������������������������11
Electrical Installation Requirements�������������������������������������������������������������������������12
Wiring Schematic������������������������������������������������������������������������������������������������13
Site Preparation / General Guidelines��������������������������������������������������������� 14-15
Installation Instructions��������������������������������������������������������������������������������������16
Water Chemistry Terms You Should Know������������������������������������������������������� 17-18
Water Quality Maintenance Schedule���������������������������������������������������������������������19
Spa Water Maintenance – Start-Up�������������������������������������������������������������������� 20-22
Water Maintenance Trouble-Shooting Guide���������������������������������������������������������23
Why Chemicals are Important in a Spa��������������������������������������������������������������������24
Maintenance Recommendations������������������������������������������������������������������������������25
Winterizing Your Spa������������������������������������������������������������������������������������������������26
Legacy Spa
Specifications������������������������������������������������������������������������������������������������������27
Controls��������������������������������������������������������������������������������������������������������� 28-29
Diagnostic Messages������������������������������������������������������������������������������������� 30-31
Fusion Docking Station��������������������������������������������������������������������������������������� 32-33
Spa Trouble-Shooting Guide������������������������������������������������������������������������������� 34-35
Regular Maintenance Procedures����������������������������������������������������������������������� 36-37
Spa Care and Maintenance Record�������������������������������������������������������������������� 38-40
2
SAFETY INSTRUCTIONS
Save These Instructions
Included with your new spa is a safety sign. The sign is for you and your guest’s protection and is
suitable for outdoor use in wet locations. The sign should be placed in a location visible to all users of
the spa.
Please take time to point out the physical location of the safety sign and the importance of the
safety precautions displayed on the safety sign to all of your guests. Remember, your safety and
the safety of anyone who enjoys the use of your spa is our utmost concern.
The sign should be mounted with screws or another type of permanent fastener. Additional or
replacement signs can be obtained from your dealer or direct from the factory.
Introduction
It’s time to relax! You now have your very own portable spa by Master Spas, Inc. By fully understanding
the operation of each of the features of your new Master Spa, you will be assured of many years of
hassle-free, hot water therapy and fun.
Your safety is of paramount importance to the MasterSpas family. We urge you to read and become
thoroughly familiar with all safety aspects addressed in this manual.
Through reading and totally understanding the important information in your owner’s manual, you will
realize that you now own THE ULTIMATE RELAXATION MACHINE!
3
SAFETY INSTRUCTIONS
Important Safety Instructions
When installing and using this electrical equipment, basic safety precautions should be
observed including the following:
Read And Follow ALL
INSTRUCTIONS
WARNING – To reduce the risk of injury, do not permit children to use this product
unless they are closely supervised at all times.
A wire conductor is provided on this unit to connect a minimum 6 AWG (13.302mm2)
solid copper conductor between this unit and any metal equipment, metal enclosures of
electrical equipment, metal water pipe, or conduit within 5 feet (1.5m) of the unit
(For cord-connected/convertible units)
DANGER – Risk of injury.
a) Replace damaged cord immediately.
b) Do not bury cord.
c) Connect to a grounded, grounding type receptacle only.
(For units intended for indoor use only)
WARNING – For indoor use only. This unit is not intended for outdoor use.
(For units intended for outdoor use only)
WARNING – For outdoor use only. This unit is not intended for indoor use.
4
SAFETY INSTRUCTIONS
Important Safety
Instructions (cont.)
(For units with GFCI)
WARNING – This product is provided with a ground-fault circuit interrupter located on the front panel of selected swim spas and on the power cord of 120 volt
convertible spas. The GFCI must be tested before each use. With the product
operating, open the service door. When the product stops operating, this merely
indicates that the door is equipped with an electrical interlock. Next, push the
test button on the GFCI and close the service door. The product should not operate. Now open the service door, push the reset button on the GFCI and close the
service door. The product should now operate normally. When the product fails
to operate in this manner, there is a ground current flowing indicating the possibility of an electric shock. Disconnect the power until the fault has been identified
and corrected.
ANGER – Risk of Accidental Drowning. Extreme caution must be exercised to prevent
D
unauthorized access by children. To avoid accidents, ensure that children cannot use
this spa unless they are supervised at all times.
DANGER – Risk of Injury. The suction fittings in this spa are sized to match the specific
water flow created by the pump. Should the need arise to replace the suction fittings
or the pump, be sure that the flow rates are compatible.
Never operate spa if the suction fittings are broken or missing. Never replace a suction
fitting with one rated less than the flow rate marked on the original suction fitting.
DANGER – Risk of Electric Shock. Install at least 5 feet (1.5m) from all metal surfaces.
As an alternative, a spa may be installed within 5 feet of metal surfaces if each metal
surface is permanently connected by a minimum 8AWG (8.4mm2) solid copper conductor to the wire connector on the terminal box that is provided for this purpose.
DANGER – Risk of Electric Shock. Do not permit any electric appliance, such as a light,
telephone, radio, or television, within 5 feet (1.5 m) of a spa.
WARNING – To reduce the risk of injury:
a) T he water in a spa should never exceed 40˚C (104˚F). Water temperatures
between 38˚C (100˚F) and 40˚C are considered safe for a healthy adult. Lower
water temperatures are recommended for young children and when spa use
exceeds 10 minutes.
5
SAFETY INSTRUCTIONS
Important Safety Instructions
(cont.)
b) S ince excessive water temperatures have a high potential for causing fetal
damage during the early months of pregnancy, pregnant or possibly pregnant
women should limit spa water temperatures to 38˚C (100˚F).
c) B
efore entering a spa, the user should measure the water temperature since the
tolerance of water temperature- regulating devices varies.
d) T he use of alcohol, drugs, or medication before or during spa use may lead to
unconsciousness with the possibility of drowning.
e) O
bese persons and persons with a history of heart disease, low or high blood
pressure, circulatory system problems, or diabetes should consult a physician
before using a spa.
f) P ersons using medication should consult a physician before using a spa since
some medication may induce drowsiness while other medication may affect
heart rate, blood pressure, and circulation.
(For spas with a gas heater)
WARNING – Risk of Suffocation. This spa is equipped with a gas heater and is
intended for outdoor use only unless proper ventilation can be provided for an
indoor installation.
HYPERTHERMIA
Hyperthermia occurs when the internal temperature of the body reaches a level
several degrees above the normal body temperature of 98.6° F.
THE SYMPTOMS OF HYPERTHERMIA INCLUDE:
• Dizziness • Fainting • Drowsiness • Lethargy
• Increase in Internal Body Temperature
THE EFFECTS OF HYPERTHERMIA INCLUDE:
nawareness of Impending Hazard • Failure to Perceive Heat • Failure to
U
Recognize the Need to Exit Spa • Physical Inability to Exit Spa • Fetal Damage in
Pregnant Women • Unconsciousness Resulting in a Danger of Drowning
6
SAFETY INSTRUCTIONS
Important Safety Instructions
(cont.)
DANGER – To reduce the risk of injury to persons, do not remove the suction grate.
Suction through drains and skimmers is powerful when the jets in the spa are in use.
Damaged covers can be hazardous to small children and adults with long hair. Should
any part of the body be drawn into these fittings, turn off the spa immediately. As a
precaution, long hair should not be allowed to float in the spa.
WARNING – Install the spa so that water can be easily drained out of the compartment
containing electrical components so as not to damage equipment. When installing the
spa make sure to allow for an adequate drainage system to deal with any overflow
water. Please allow for at least 2 feet of clearance around the perimeter of the spa to
provide enough room to access for servicing. Contact your local dealer for their specific
requirements.
WARNING – The spa should be covered with an approved locking cover when not in
use, to prevent unauthorized entry and injuries.
WARNING – People with infections, sores or the like should not use the spa. Warm and
hot water temperatures may allow the growth of infectious bacteria if not properly disinfected.
CAUTION – Safe temperatures for swimming or aquatic exercise is around 80˚F.
AUTION – Risk of Electrical Shock. Do not leave CD compartment open. CD controls
C
are not to be operated while inside the spa.
CAUTION – Replace components only with identical components.
WARNING – Risk of Electric Shock. Do not connect any auxiliary components (for
example, additional speakers, headphones, additional audio/ video components etc.) to
the system. These units are not provided with an outdoor antenna.
Do not service this product yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
If the power supply cord(s) are damaged, water is entering the speaker, CD compartment, or any other component in the electrical equipment compartment area, the protective shield is showing signs of deterioration, or there are signs of other potentially
hazardous damage to the unit, turn off the circuit breaker from the wall and refer servicing to qualified personnel.
7
SAFETY INSTRUCTIONS
Important Safety Instructions
(cont.)
T he unit should be subjected to periodic routine maintenance once every quarter to
make sure that the it is operating properly.
DANGER – Risk of Electric Shock. A green colored terminal or a terminal marked G,
GR, Ground, Grounding or the symbol shown in Figure 14.1 of UL 1563 is located
inside the supply terminal box or compartment. To reduce the risk of electric shock,
this terminal must be connected to the grounding means provided in the electric supply
service panel with a continuous copper wire equivalent in size to the circuit conductors
supplying this equipment.
t least two lugs marked “Bonding Lugs” are provided on the external surface or on
A
the inside of the supply terminal box or compartment. To reduce the risk of electric
shock, connect the local common bonding grid in the area of the spa to these terminals
with an insulated or bare copper conductor not smaller than 6AWG.
ll field installed metal components such as rails, ladders, drains, or other similar hardA
ware within 3m of the spa shall be bonded to the equipment grounding bus with copper conductors not smaller than 6AWG.
SAVE THESE INSTRUCTIONS
8
SAFETY INSTRUCTIONS
Warning: Children should not use spas or hot tubs without adult supervision
Avertissement: Ne pas laisser les enfants utiliser une cuve de relaxation
sans surveillance
Warning: Do not use spas or hot tubs unless all suction guards are installed
to prevent body and hair entrapment.
Avertissement: Pour éviter que les cheveux ou une partie du corps puissent
être aspires, ne pas utiliser une cuve de relaxation si les grilles di prise d’aspiration ne
sont pas toutes en place
Warning: People using medications and/or having an adverse medical history
should consult a physician before using a spa or hot tub.
Avertissement: Les personnes qui prennent des médicaments ou ont
des problémes de santé devraient consulter un médecin avant d’utiliser une cuve de
relaxation
Warning: People with infectious diseases should not use a spa or hot tub
Avertissement: Les personnes atteintes de maladies infectieuses ne devraient
pas utiliser une cuve de relaxation
Warning: To avoid injury exercise care when entering or exiting the spa or hot
tub.
Avertissement: Pour éviter des blessures, user de prudence en entrant dans
une cuve de relaxation et en sortant
Warning:
Do not use drugs or alcohol before or during the use of a spa or
hot tub to avoid unconsciousness and possible drowning
Avertissement: Pour éviter l’évanouissement et la noyade éventuelle, ne
prende ni drogue ni alcool avant d’utiliser une cuve de relaxation ni quand on s’y
trouve
Warning:
Pregnant or possibly pregnant women should consult a physician
before using a spa or hot tub.
Avertissement: Les femmes enceintes, que leur grossesse soit confirmée ou
non, devraient consulter un médecin avant d’utiliser une cuve de relaxation
Warning: Water temperature in excess of 38˚C may be injurious to your health
Avertissement: Il peut être dangereux pour la santé de se plonger dans de
l’eau a plus de 38˚C
Warning: Before entering the spa or hot tub measure the water temperature
with an accurate thermometer
Avertissement: AVant d’utiliser une cuve de relaxation mesurer la
température de l’eau À l’aide d’un thermométre précis
9
SAFETY INSTRUCTIONS
Warning: Do not use a spa or hot tub immediately following strenuous exercise
Avertissement: Ne pas utiliser une cuve de relaxation immédiatement
aprés un exercise fatigant
Warning: Prolonged immersion in a spa or hot tub may be injurous to
your health
Avertissement: L’utilisation prolongée d’une cuve de relaxation peut
être dangereuse pour la santé
Warning:
Do not permit electric appliances (such as light, telephone,
radio, or television) within 1.5 m of this spa or hot tub
Avertissement:
Ne pas placer d’appareil électrique (luminaire, téléphone, radio, téléviseur, etc) À moins de 1.5 m de cette cuve de relaxation
Caution: Maintain water chemistry in accordance with manufacturer’s
instruction
Attention: La teneur de l’eau en matiéres dissoutes doit être conforme
aux directives du fabricant
Hyperthermia occurs when the internal temperature of the body reaches a level several
degrees above the normal body temperature of 37˚C. The symtoms of hyperthermia
include drowsiness, lethargy, and an increase in the internal temperature of the body.
The effects of hyperthermia include
(a) unawareness of impending hazard;
(b) failure to perceive heat;
(c) failure to recognize the need to exit spa;
(d) physical inability to exit spa;
(e) fetal damage in pregnant women; and
(f) unconsciousness and danger of drowning.
Warning:
The use of alcohol or drugs can greatly increase the risk of
fatal hyperthermia in hot tubs and spas
La Consommation d’alcool ou de drogue augmente considérablement les
risques d’hyperthermie mortelle dans une cuve de relaxation.
10
GLOSSARY OF SPA TERMINOLOGY
1. D
RAINING YOUR LEGACY SPA. The drain is located behind
the front panel on the far right side, grasp the hose bib
cap and turn it counter clockwise. Attach a garden hose,
if desired. Turn the black knob on the side of the valve a
quarter turn. Draining times may vary by model using the
external hose bib. A sump pump may also be used to drain
the spa quickly.
2. MAIN
PUMP. This produces water flow through the main jets in the spa. The first pump may be operated on two speeds. Low speed will produce
efficient water circulation during filtration and gentle jet action. High speed should be used for maximum jet action. The main pump is controlled by the “Jets” or “Jets I” button on the Topside Control Panel.
3. SECONDA
RY PUMP. This produces water flow through the other jet system in
the spa (if applicable). The second pump operates similar to the main pump
and is controlled by the “Jets II” button on the Topside Control Panel.
4. P
UMP UNION. These are used by service personnel to easily
service the pump(s).
5. HEA
TER UNION. These are used by service personnel to easily
service the heater.
6. O
ZONATOR. Your optional ozonator will operate in conjunction with your
filtration system. It will deactivate when any other control function is
manually activated and will reactivate after one hour of inactivity.
Ozonator (optional)
11
ELECTRICAL INSTALLATION REQUIREMENTS
HAVE YOUR ELECTRICIAN READ THE FOLLOWING
INFORMATION BEFORE INSTALLATION BEGINS
Electrical connections made improperly, or the use of wire gauge sizes
for incurring power which are too small, may continually blow fuses in the
electrical equipment box, may damage the internal electrical controls and
components, may be unsafe and in any case will void your warranty.
It is the responsibility of the spa owner to ensure that electrical
connections are made by a qualified electrician in accordance with the
National Electrical Code and any local and state electrical codes in force
at the time of installation.
These connections must be made in accordance with the wiring
diagrams found inside the control box. This equipment has been
designed to operate on 60Hz. alternating current only, 240 volts are
required. Make sure that power is not applied while performing any
electrical installation. A copper bonding lug has been provided on the
electrical equipment pack to allow connection to local ground points.
The ground wire must be at least 6 AWG copper wire (unless local
or state codes require a heavier gauge wire) and must be connected
securely to a grounded metal structure such as a cold water pipe. All
Master Spas equipment packs are wired for 240 VAC only. The only
electrical supply for your spa must include a 50 AMP switch or circuit
breaker to open all non-grounded supply conductors to comply with
section 422-20 of the National Electrical Code. The disconnect must be
readily accessible to the spa occupants, but installed at least five feet
from the spa. A Ground-Fault Circuit Interrupter (GFCI) must be used to
comply with section 680-42 of the National Electrical Code. A ground
fault is a current leak from any one of the supply conductors to ground.
A GFCI is designed to automatically shut off power to a piece of
equipment when a current fault is detected.
Power hook-up to the spa must be 240 volt 3 wire plus ground
(6 AWG copper).
Route the cable into the equipment area for final hook-up to terminals
inside the control panel. The spa must be hooked up to a “dedicated”
240 volt, 50 amp breaker and GFCI. The term “dedicated” means the
electrical circuit for the spa is not being used for any other electrical items
(patio lights, appliances, garage circuits, etc.). If the spa is connected to
a non-dedicated circuit, overloading will result in “nuisance tripping”
which requires resetting of the breaker switch at the house
electrical panel.
Rev. 11/07
Permanently Connected Equipment Assembly with Pump(s), Heaters, Luminaine,
Ozone, Spa Side Control(s), Pump shut off device, and Audio/Video Components.
NOTE: Some of the above components may be optional or not available with
every spa model.
12
WIRING SCHEMATIC - 240 VOLT SPA HOOK-UP
Balboa
Instruments
G.F.C.I Breaker Box
Incorporated
Wire Key
Green (Ground)
Red (Hot)
Black (Hot)
White (Neutral)
50
TEST
House Breaker Box
50
ON
OFF
OFF
ON
OFF
ON
GRN (GROUND)
ON
OFF
BLK (HOT)
ON
OFF
RED (HOT)
WHT
GRN
BLK (HOT)
GRN (GROUND)
RED (HOT)
WHT
BLK (HOT)
RED (HOT)
Spa System Box
TB1
1
2
3
4
5
WHITE (NEUTRAL)
BLACK (HOT)
RED (HOT)
GREEN (GROUND)
NOTE: For a 240 V
dedicated hook-up, the
white neutral wire is
not required between
the G.F.C.I. and the
system box.
WHT (NEUTRAL)
IDF00007.mac 6/17/97
*A
ctual wiring of GFCI will vary by manufacturer of GFCI. The GFCI shown is a
Square D. Improper wiring of GFCI may result in permanent damage to spa system box.
Repair / replacement of spa system box is not covered under warranty when damage
results from improper wiring.
13
SITE PREPARATION / GENERAL GUIDELINES
Portable spa installation is simple when properly planned. To that end, it is
important that you read the following information carefully and consult with
your Master Spas dealer.
1) Access - The actual dimensions of your new spa will determine the amount of space that is needed in moving the spa from curbside to its final installation area. Be sure to measure side yard dimensions, gates or doors and vertical obstructions such as roof overhangs and overhead cables. Any other space
limiting obstacles such as trees or shrubs must be evaluated.
2) If the spa is being installed indoors, dimension limitations such as stairs,
ceilings and walls must be taken into consideration. Please have your
Master Spas dealer or delivery service review site or installation plans
prior to delivery.
NOTE: If you are installing your spa indoors, always be aware that if you splash
water into the speaker compartments of the spa, water will run down through
the speaker drain at the floor level toe kick, which drains below the spa in the
corner where the speakers are located. Please be aware of this as any damage
is not covered by the warranty. This could cause unwarranted damage. The VS
Series spas do not have stereo systems installed.
3) S
urface/Pad Requirements - When your new spa is filled with water and bathers, it may weigh as much as several tons. It is imperative that the base beneath the spa can support the actual weight. The spa must be on a
uniformly firm, continuous, and level surface. The recommended foundation is a concrete pad with a minimum thickness of four (4) inches with steel
reinforcement bars crossed throughout the pad.
IMPORTANT
When installing your spa indoors, on a wood deck, or balcony, the same
load requirements must be met. Total load may be as much as 90 pounds per
square foot. You should speak with a qualified contractor or your local building
department to confirm that your surface is adequate for supporting a spa.
Be sure to locate your spa so that equipment remains above grade and is
not subject to flooding.
The equipment side(s) of the spa must be accessible in the event that
future service is needed. Periodical maintenance checks require entry into the
equipment bay. When possible, it is wise planning for the future to leave access
to all sides of the spa in the event your spas plumbing requires maintenance.
Your spa warranty does not cover the cost of providing access for service.
14
SITE PREPARATION / GENERAL GUIDELINES
GENERAL CONSIDERATIONS FOR OUTDOOR INSTALLATION
Again, proper planning will increase your total enjoyment factor with your new
spa. Listed below are some additional items to consider when planning your
installation.
• How spa will complement landscaping and vice versa
• View from inside spa and view of spa from inside of home
• Exposure to sunlight and shading from trees
• Privacy
• Getting to spa from house and return
• Proximity to dressing rooms and bathrooms
• Storage for spa chemicals
• Local building codes (if applicable)
• Power cable
GENERAL CONSIDERATIONS FOR INDOOR INSTALLATION
Installing your spa indoors creates an entirely different set of considerations.
Here again, with proper planning, no matter what room your spa goes in, it will
be your favorite room.
•W
ork with your Master Spas dealer and contractor to insure all local building,
electrical and plumbing codes are met
•P
lan for a floor drain to drain off excess water or for draining
and cleaning your spa
• A ventilation fan may be necessary due to high humidity created by your spa
• F inished material in your spa room should also be capable of withstanding increased humidity
• If you are installing your spa indoors, always be aware that if you splash
water into the speaker compartments of the spa, water will run down through
the speaker drain at the floor level toe kick, which drains below the spa in the
corner where the speakers are located. Please be aware of this as any damage
is not covered by the warranty. This could cause unwarranted damage.
15
INSTALLATION INSTRUCTIONS
1.) P
ut spa in final position that allows for access to equipment
and spa components.
2.) R
emove front side panel (This is the side where
the main topside control panel is located) so
electrical can be hooked up to the spa system pack.
Panels are removed by unscrewing the screws in the
corner sections and side panels (using #2 square bit).
Using a phillilps screwdriver may result in stripping
of the screw.
3.) F ill spa at least 1” above the filters. We recommend filling
the spa through the filter area.
4.) T
urn the power on to the spa. Spa will go through its priming mode.
This lasts approximately 5 minutes.
5.) It may be necessary to bleed air from the motor(s) on your spa if, after start up, your spa pumps do not operate.
Due to the nature of water flow and hydro-therapy pumps, please be advised
that air locking of pumps may occur. Master Spas has taken measures to reduce the possibility of this, but it still may occur, especially after refilling
a spa. This is not a service covered under warranty.
To relieve an airlock situation, loosen the union (see picture) on the discharge
of the pump (the end of the pump that water is being pushed through).
Water should leak out. Tighten the union and test the pump for proper jet
flow. If needed repeat process.
Pump Union
Airlock
6.)Adjust water chemistry according to the instructions provided in the
“Spa Water Maintenance Section” (page 20).
7.)Your spa water will heat approximately 4° - 7° per hour, for all 240V spas.
This varies depending on the size of the spa. Step into the soothing waters
of your new Master Spa!
Relax and enjoy.
16
WATER CHEMISTRY TERMS YOU SHOULD KNOW
Before jumping into the Spa Water Maintenance, here are some terms to help you.
1. Parts per million, or ppm: This is a form of measurement used in most pool or spa chemical readings. Best described as any one million like items of equal size and make up, next to one unlike item , but of equal size. This would be one part per million.
2. A
verage size spa: What is it? The national spa and pool institute (NSPI) states; 350 to 400 U.S. gallons is average. As a general rule, chemical dosages
are the same for any spa between 100 and 500 U.S. gallons. Spas over 500 U.S. gallons the dosage would be double. Under 100 U.S. gallons would be on a case by case basis.
3. T
otal Alkalinity: This is a measurement of the ability of the water to resist changes in pH. Put another way, it is the water’s ability to maintain proper pH. Total alkalinity is measured in parts per million from 0 to 400 plus, with 80 to 150 ppm being the best range for spas. With low alkalinity, the pH will flip, or change back and forth, and be hard to control. With high alkalinity it becomes extremely difficult to change the pH.
4. p
H or potential hydrogen: This is a measurement of the active acidity in
the water, or it is the measurement of the concentration of active hydrogen
ions in the water. The greater the concentration of active hydrogen ions, the
lower the pH. pH is not measured in parts per million, but on a scale from 0
to 14, with 7 being the neutral. In spas when ever possible, a measurement
between 7.2 and 7.8 is best. Whenever possible, it should be between 7.4
and 7.6. With low pH, the results can be corroded metals, etched and stained
plaster, stained fiberglass or acrylic, eye / skin irritation, rapid chlorine or
bromine loss, and total alkalinity destruction. With high pH, the results can
be cloudy water, eye / skin irritation, scale formation and poor chlorine or
bromine efficiency.
5. S
hocking: This is when you add either extra chlorine (superchlorinate)
by raising the chlorine level above 8 ppm, or add a non-chlorine shock
(potassium monoperoxysulfate or potassium monopersulfate) to burn off the
chloramines or bromamines. A non-chlorine shock acts by releasing oxygen
in the water, which serves the same function as chlorine. The advantage to
using non-chlorine shock, is you can enter the water within 15 minutes after
shocking. Using chlorine, you must wait until the total chlorine reading is
below 5 ppm. One thing to remember, a non-chlorine shock will not kill
bacteria or disinfect.
6. S
equestering: This can be defined as the ability to form a chemical
complex which remains in solution, despite the presence of a precipitating
agent (i.e. calcium and metals). Common names for sequestering chemicals
are; minquest, stain and scale control, metal-x, spa defender, spa metal
gone, (etc.).
17
WATER CHEMISTRY TERMS YOU SHOULD KNOW
Before jumping into the Spa Water Maintenance, here are some terms to help you.
7. F iltration: Filters are necessary to remove particles of dust, dirt, algae, etc. that are continuously entering the water. If the spa is not operated long enough each day for the filter to do a proper job, this puts a burden on the chemicals, causing extra expense. Filtration time will depend on the spa size, pump and filter size, and of course, bather load. A spare cartridge should be kept on hand to make it easy to frequently clean the cartridge without the need for a long shut down. This will also allow the cartridge to dry out between usages, which will increase the cartridge life span as much as twice. Replace the cartridge when the pleats begin to deteriorate. Cartridge
cleaning should be done a minimum of once a month. More often with
a heavy bather load.
8. S
anitizers: This is what kills the germs and bacteria that enter the water from
the environment and the human body.
A. Chlorine
1. Only one type is good for spa use
a. Sodium dichlor which is a granule, fast dissolving,
and pH neutral
2. Chlorine is an immediate sanitizer.
B. Bromine
1. Two types of tablets.
a. Hydrotech
b. Lonza
2. Bromine is a slow dissolve chemical and may take a few days to
develop a reserve or reading in the water.
9.Total dissolved solids (TDS): Materials that have been dissolved by the water. i.e. Like what happens when you put sugar in coffee or tea.
10.Useful life of water (in days): Water should be drained at least once every
180 days. Useful life may vary by usage and bather load.
11.Defoamer: Foaming may be caused by body oils, cosmetics, lotions, surface cleaners, high pH or algeacides as well as other organic materials. Low
levels of calcium or sanitizer can also cause foaming. Also, double rinse
your bathing suits as they will hold residual soap after being washed.
12.Calcium hardness: Water that is too hard (over 250 ppm) can promote scale formation in components and on spa surface. Water that is too low (below
180 ppm) may also shorten the life of metal components on the spa.
NOTE: Always leave the spa cover open for 15 min. after adding chemicals
to prevent off gas from damaging your spa cover, spa pillows, and other
critical parts.
18
WATER QUALITY MAINTENANCE SCHEDULE
BEFORE EACH USE - Check spa water with a test strip for proper sanitation levels and adjust accordingly to the proper levels.
ONCE A WEEK -Add 3 Tablespoons of a non-chlorine shock or
1 teaspoon of Dichlor to spa per 250 gallons.
3 TIMES A WEEK -Test water using chemical test strips. Adjust sanitizer, pH and Alkalinity accordingly.
ONCE A MONTH* - Soak your filter element overnight in a bucket with
spa Filter Cleaner and then rinse with clean water
before re-inserting.
EVERY 180 DAYS - Drain and refill your spa. Repeat start up procedure.
AFTER EACH USE - Add 1 tablespoon of non-chlorine shock or 1/3
teaspoon of Dichlor to spa per 250 gallons.
AS NEEDED - If water looks hazy, shock treat with 1 teaspoon of Dichlor per 500 gallons.
*T
hese are general recommendations for water quality maintenance that
may vary by usage and or bather load. Depending on bather load and
frequency of use, drain and refill times may vary as well as the frequency
of cleaning your filters.
* F oam Gone may be used when excessive foaming occurs. Be sure to use
only a drop or two at a time. Over use of Foam Gone will result in cloudy,
milky water.
Note:
As an alternative to non chlorine shock, Dichlor may be substituted.
1 tsp. Dichlor = 3 tablespoons of non chlorine shock
USE ONLY SPA CHEMICALS
(some pool chemicals are not suitable for spa use).
*w
hen cleaning filters, be sure to never have the pump(s) running without
the filter in place. Failure to do so may result in debris in the pumps causing
unwarranted damage.
19
SPA WATER MAINTENANCE - START-UP
1. Read the spa owners manual first.
2. C
lean the surface with a spa general purpose cleaner or wipe down with a clean wet towel.
3. Begin filling the spa with fresh water. If possible, do not use softened water.
4. W
hen the spa has 2 to 4 inches of water on the bottom, add the recommended
amount of a sequestering chemical for that size spa. See the chemical bottle
for correct amounts.
5. W
hen the spa is full, run the pump on high speed for 30 minutes without air controls open. This will give the sequestering chemical time to mix well with the water. Allow sequestering chemical 12-24 hours to properly filter in the water before proceeding with any further steps.
6. Using test strips or a test kit, test for total alkalinity, and adjust if necessary
to between 80 to 150 ppm using the pH / alkalinity increaser or decreaser 1oz.
at a time. Wait 15 minutes, retest, and adjust if necessary. The pump should be running on high speed during this time.
7. Using test strips or a test kit, test for pH, and adjust if necessary to within the 7.2 and 7.8 range using the pH / alkalinity increaser or decreaser 1/2oz. at a time. Wait 15 minutes, retest, and adjust if necessary. The pump should be running on high speed during this time, without air controls open.
8. A
dd the sanitizer of choice, following label directions. If chlorine is used, broadcast the recommended amount across the surface of the water, with the pump running on high speed. Wait 15 minutes, retest, and adjust if necessary to a total chlorine reading of 1 to 3 ppm. If bromine is used, add bromine tablets to the bromine feeder following label directions. With the pump
running on high speed, add 2oz. of sodium bromide, and shock the spa with 2oz. of non chlorine shock. It may take several days adjusting the bromine feeder to obtain a total bromine reading of 3 to 5 ppm. A bromine reading may not be obtained on the first day.
9. If any foam develops, add a defoamer at the base of the problem area. Use
only enough defoamer to get rid of the foam. This is usually one or two drops. Do not pour large amounts of defoamer into water.
10. Wait two days, and begin a three day a week maintenance program.
20
SPA WATER MAINTENANCE - START-UP
Day One
1. T
est and adjust total alkalinity if necessary to between 80 to 150 ppm using the pH / alkalinity increaser or decreaser 1oz. at a time. Wait 15 minutes, retest and adjust if necessary. The pump should be running on high speed during this time with the air controls closed.
2. T
est and adjust pH, if necessary, to within the range of 7.2 to 7.8 using the
pH / alkalinity increaser or decreaser, 1/2oz. at a time. Wait 15 minutes, retest and adjust if necessary. The pump should be running on high speed during this time with the air controls closed.
3. T
est and adjust sanitizer level. Add chlorine following label directions to maintain a free chlorine level of 1 to 3 ppm. If using bromine, adjust feeder to maintain a total bromine level of 3 to 5 ppm. Add bromine tablets to the dispenser if necessary, following label directions.
4. A
dd a water clarifier following label directions. If the spa is equipped with an ozone unit, we recommend adding an enzyme product in place of the clarifier, following the label directions.
5. Use a small amount of defoamer only if necessary.
Day Two Skip
Day Three
1. T
est and adjust total alkalinity, if necessary, to between 80 and 150 ppm using the pH / alkalinity increaser or decreaser, 1oz at a time. Wait 15 minutes, retest and adjust if necessary. The pump should be running on high speed during this time with the air controls closed.
2. T
est and adjust the pH, if necessary, to within the range of 7.2 to 7.8 using the pH / alkalinity increaser or decreaser, 1/2oz at a time. Wait 15 minutes, retest and adjust if necessary. The pump should be running on high speed during this time with the air controls closed.
3. T
est and adjust sanitizer level. Add chlorine following label directions to maintain a free chlorine level of 1 to 3 ppm. If using bromine, adjust feeder to maintain a total bromine level of 3 to 5 ppm. Add bromine tablets to the dispenser if necessary, following label directions.
4. Add sequestering chemical, following label directions for maintenance.
5. If necessary, clean water line with a spa general purpose cleaner
or enzyme product.
6. Use a defoamer only if necessary.
(cont. next page)
21
SPA WATER MAINTENANCE - START-UP
Day Four Skip
Day Five
1. T
est and adjust total alkalinity, if necessary, to between 80 and 150 ppm using the pH / alkalinity increaser or decreaser, 1oz. at a time. Wait 15 minutes, retest and adjust if necessary. The pump should be running on high speed during this time with the air controls closed.
2. T
est and adjust the pH, if necessary, to within the range of 7.2 to 7.8 using the pH / alkalinity increaser or decreaser, 1/2oz. at a time. Wait 15 minutes, retest and adjust if necessary. The pump should be running on high speed during this time with the air controls closed.
3. T
est and adjust sanitizer level. Add chlorine following label directions to maintain a free chlorine level of 1 to 3 ppm. If using bromine, adjust feeder to maintain a total bromine level of 3 to 5 ppm. Add bromine tablets to the dispenser if necessary, following label directions.
4.Shock with 2oz. of non chlorine shock, or superchlorinate following label directions. A spa should be shocked at least once a week even if it is not used. If using chlorine as the sanitizer, the spa should be shocked whenever a free chlorine reading of 1 to 3 ppm cannot be obtained without raising the total chlorine level above 5 ppm. Always shock a spa after any heavy bather load.
5. C
heck filter cartridge and clean if necessary. Clean with cartridge filter cleaner, following label directions. It is best to have a spare cartridge on hand, to prevent long spa down times while the cartridge is being cleaned.
Never operate your spa without the filters in place.
6. Use a defoamer only if necessary.
Day Six and Seven Skip
With a spa, you are working with a small volume of hot water, which causes
chemicals to have a shorter life span, and bacteria, along with other things, to
grow faster. A spa is less forgiving than a pool, and requires that whatever is
put into it have a pH as close to neutral as possible. That is why only chemicals
made for spas should be used.
22
SPA WATER MAINTENANCE
TROUBLE-SHOOTING GUIDE
Problem
Possible Causes
How To Fix It
Chlorine / Bromine Odor
•E
xcessive Chlorine or
bromine levels
• S hock water with nonchlorine shock treatment
• Low pH
• Adjust pH if necessary
• Low levels of sanitizer
• S hock water with nonchlorine shock treatment
or adjust sanitizer levels
• pH out of range
• Adjust pH level if necessary
• Bacteria or algae growth
• Adjust sanitizer if necessary
•D
irty filters or
inadequate filtration
•C
lean filters and adjust
filtration times
•W
ater chemistry
not balanced
•A
djust chemistry
levels
• S uspended particles or
organic materials
•A
dd spa clarifier
(see dealer)
• Old water
• Change spa water
Scum Ring Around Spa
•B
uild up of oils, dirt and
organic elements
•W
ipe off with
a clean towel
Eye / Skin Irritation
• Unsanitary water
• S hock spa with
non-chlorine shock
• F ree chlorine level
above 5 ppm
•A
llow level to drop
below 5 ppm
• Poor sanitizer / pH levels
•A
djust according to spa
test strip results
•H
igh levels of body oils,
lotions, soap, etc.
•A
dd small amount
of defoamer
Water Odor
Cloudy Water
Foaming
Recommended Levels of Chemical
Chlorine 1.0 - 3.0 ppm
pH 7.2 - 7.8
Total Alkalinity 80 - 150 ppm
Calcium Hardness 180 - 250 ppm
23
WHY CHEMICALS ARE IMPORTANT IN A SPA
1. E
vaporation: As water evaporates, only pure water evaporates, leaving the salts, minerals, metals, and any unused chemicals behind. Adding water adds more salts, minerals, and metals. In time, the water can become saturated with these dissolved solids and can cause stains or scale to form on the walls
of the spa or a scale build up inside the equipment. Colored or cloudy water,
and possible corrosion of plumbing and fittings may also occur.
2. H
eat: Heat causes evaporation to happen faster. Heat also causes certain minerals and metals to precipitate out of solution.
3. Air: Dust and airborne dirt particles are introduced into the spa.
4. Environment: The environment surrounding the spa is also a consideration. Watch for pollen, grass, sand, dirt, lawn fertilizer, dust storms, insects, dogs, cats, etc.
5. C
onsider the human next: In a heated spa, the average adult sweats 3 pints per hour. This person also brings in the spa surface dirt, soap, body oils, deodorant, hair spray, hand and body lotion, perfume and cologne, make up, lipstick, and suntan lotion. To this you can add spit, urine, bacteria and virus germs from open sores or certain body parts. To this let’s add spilled drinks, cigarette ash, and various play things. Now multiply this times 4 or 6 people in an average 375 gallon spa and then try to use the water for a few months!
Remember:
The maintenance routines set forth in this manual may need to be adjusted
depending on how much the spa is being used.
24
MAINTENANCE RECOMMENDATIONS
Your spa requires periodic draining and cleaning to ensure a safe, healthy
environment. It is recommended that you clean your spa at least every 180 days.
Heavy bather load will require cleaning it more often.
TO DRAIN YOUR SPA
• See page 11.
TO CLEAN YOUR SPA SURFACE
• With a soft cloth, wipe down the spa surface with a non-abrasive spa surface cleaner that may be purchased through your local spa dealer. Do not use paper
towels. Be sure to rinse residue from spa surface.
• If your spa has developed an oily or chalky residue at the waterline it may require special treatment. Consult your dealer.
TO REFILL YOUR SPA
• Be sure to close the drain valve.
• F ill the spa with water. Be sure water level is above skimmer opening to the minimum safe water level label.
• Refer to your spas corresponding start-up section with any questions.
TO CLEAN YOUR FILTER ELEMENT (also reference page 36)
The filter in your spa is one of the most important components of your spa.
It not only is essential for clean water, but also for extending the life of the spa
equipment. Your filter element must be cleaned regularly (once a month on
average) with normal spa use. With heavy use, they will need to be cleaned
more often.
•T
urn spa off. Never have the spa running when removing your filter as debris can be pulled through into the equipment causing unwarranted damage.
• Remove filter element.
•W
ith a garden hose, spray the element under pressure. Periodically, the
element needs to be soaked in a filter cleaner compound. Check with your dealer for details on cleaning and/or filter replacement recommendations.
• Replace filter element.
• Be sure water level is adequate.
• Turn spa on.
CARE OF YOUR SPA PILLOWS
•Y
our spa pillows need to be rinsed periodically to remove any chemical residue. This should help to eliminate pillows becoming stiff and discolored.
• If spa is not to be used for a period of time, pillows should be removed.
Pillow life will be extended.
25
WINTERIZING YOUR SPA
Many people find they enjoy using their spa more in the winter than any other
time. Your spa is designed to be used year round in any type of climate.
*However, if you decide you don’t want to use your spa in the winter, you must
drain it and follow the winterizing steps listed below:
1.) D
rain your spa completely using the drain valve (see “To Drain Your Spa”)
or use an inexpensive submersible pump that you can buy from your dealer
or your local hardware store.
2.) Use a shop vac to get all standing water out of your unit.
3.) Remove access panels from equipment area.
4.) Loosen all pump unions
5.) Remove winterizing plug from the face of the pump(s).
6.) Using your shop vac in a blowing mode, insert the hose into the nozzle
of each jet and blow the trapped water from the lines into the interior
of the spa.
7.) A
fter this is completed, use the shop vac to remove any standing water
in the spa and in the equipment area.
8.) Clean the spa with a soft cloth and a non-abrasive spa surface cleaner.
9.) Replace access panels.
10.) Cover spa to prevent water from entering the spa.
* Disclaimer: Master Spas does not recommend winterizing your spa.
If you choose to do so, any damage that may result is not covered
under the spa warranty.
26
LEGACY SPA - SPECIFICATIONS
Spa
Water
Weight
DimensionsElectricalCapacityDry/Full TherapyJet
(in.)
Requirements
(gallons)
(lbs.)PumpsCount
INTREPID
94 x 94 x 36 240V, 485
50 Amp
700 / 7,740
2
40
ENTERPRISE 84 x 84 x 36
240V, 410
50 Amp
655 /
4,070
2
40
INSPIRE
84 x 84 x 36
240V, 425
50 Amp
650 /
4,190
2
40
ENVISION
78 x 84 x 32
240V, 320
50 Amp
580 /
3,245
1
28
27
LEGACY SPA - CONTROLS
Initial Start-up
When your spa is first actuated, it will go into Priming mode, indicated by
“ ” The Priming mode will last for less than 5 minutes (press “Warm” or
“Cool” to skip Priming mode) the spa will begin to heat and maintain the
water temperature in the Standard mode.
Warm / Cool (80˚F-104˚F / 26˚C-40˚C)
The start-up temperature is set at 100 degrees F / 37 degrees C. The last
measured temperature is constantly displayed on the LCD display.
1 Pump System
To display the set temperature, press the “Warm” or “Cool” button once.
To change the set temperature, press the button a second time before the
LCD stops flashing. Each press of the “Warm” or “Cool” button will continue
to either raise or lower the set temperature.
2 Pump System
To display the set temperature, press the “Temp” pad once. To change
temperature, press the pad a second time before the LCD stops flashing.
Each press of the “Temp” pad will continue to either raise or lower the set
temperature.
If the opposite direction is desired, release the pad and let the
display revert to the current water temperature. Press the pad to display
the set temperature, and again to make the temperature change in the
desired direction.
After three seconds, the LCD will stop flashing and display the current
spa temperature.
Jets
Press the jets button once to activate the pump on low speed. Press the jets
button again to turn the pump on high speed. If left running on low speed
the pump will automatically turn off after 4 hours, and the high speed will
automatically turn off after 15 minutes.
28
LEGACY SPA - CONTROLS
Light
Press the “Light” button to turn the light on and off. If left on, the light
automatically turns off after 4 hours.
Mode
Mode is changed by pressing the “Temperature” button (Warm or Cool on some
models) and then the “Light” button to cycle through the different modes.
Standard Mode is programmed to maintain the desired temperature. Note
that the last measured spa temperature displayed is current only when the
low speed of pump 1 has been running for at least 2 minutes. “ ” will be
displayed momentarily when you switch into the Standard Mode.
Economy Mode heats the spa to the set temperature only during filter cycles.
“ ” will display solid when temperature is not current, and will alternate
with temperature when temperature is current.
Sleep Mode heats the spa to within 20°F/10°C of the set temperature only
during filter cycles. “ ” will display solid when temperature is not current,
and will alternate with temperature when temperature is current.
Preset Filter Cycles
The first filter cycle begins 6 minutes after the spa is energized. The second filter
cycle begins 12 hours later. Filter duration is programmable for 2, 4, 6, 8 hours
or for continuous filtration (indicated by “ ”). The default filter time is 2
hours.
To program press the “temperature” button (Warm or Cool button on some
models) then the “Jets” button to adjust. Press “Jets” to exit programming.
At the beginning of each filter cycle the pump(s) purge for 30 seconds. The only
effect filter duration has is: 1) During the filter cycle, the low speed of pump 1
never turns off. 2) In Economy and Sleep modes, heating only occurs during the
filter cycle.
Freeze Protection
If the temperature sensors detect a drop to below 44°F/6.7°C within the
heater, the pump will automatically activate to provide freeze protection.
The equipment stays on until 4 minutes after the sensors detect that the spa
temperature has risen to 45°F/7.2°C or higher. In colder climates, an optional
additional freeze sensor may be added to protect against freeze conditions
that may not be sensed by the standard sensors. Aux freeze sensor protection
acts similarly except with the temperature thresholds determined by the switch
and without a 4-minute delay in turnoff. See your dealer for details.
29
LEGACY SPA - DIAGNOSTIC MESSAGES
MESSAGE
MEANING
ACTION REQUIRED
No message on display.
Power has been cut off
to the spa.
The control panel will be disabled until
power returns. Spa settings will be
preserved until next power up.
Temperature
unknown.
After the pump has been running
for 2 minutes, the temperature will
be displayed.
“Overheat” - The spa
has shut down. One
of the sensors has
detected 118°F/48°C at
the heater.
DO NOT ENTER THE WATER. Remove the
spa cover and allow water to cool. Once
the heater has cooled, reset by pushing
any button. If spa does not reset, shut
off the power to the spa and call your
dealer or service organization.
“Overheat” - The spa
has shut down. One of
the sensors has detected
that the spa water is
110°F/43°C.
DO NOT ENTER THE WATER. Remove the
spa cover and allow water to cool. At
107°F/42°C, the spa should automatically
reset. If spa does not reset, shut off the
power to the spa and call your dealer
or service organization.
“Ice” - Potential freeze
condition detected.
No action required. The pump(s) will
automatically activate regardless of
spa status.
Spa is shut down. The
sensor that is plugged
into the Sensor “A”
jack is not working.
If the problem persists, contact your
dealer or service organization. (May
appear temporarily in an overheat
situation and disappear when the
heater cools.)
Spa is shut down. The
sensor that is plugged
into the Sensor “B”
jack is not working.
If the problem persists, contact your
dealer or service organization. (May
appear temporarily in an overheat
situation and disappear when the
heater cools.)
30
LEGACY SPA - DIAGNOSTIC MESSAGES
MESSAGE
MEANING
ACTION REQUIRED
Sensors are out of
balance. If alternating
with spa temperature,
it may just be a
temporary condition.
If flashing by itself,
spa is shut down.
If the problem persists, contact your
dealer or service organization.
A significant difference
between temperature sensors has been
detected. This could
indicate a flow
problem.
Check water level in spa. Refill if
necessary. If the water level is okay,
make sure the pumps have been primed.
If problem persists, contact your dealer
or service organization.
Persistent low flow
problems. (Displays on
the fifth occurrence of
“ ” message within
24 hours.) Heater is
shut down, but other
spa functions continue
to run normally.
Follow action required for “ ”
message. Heating capability of the spa
will not reset automatically; you may
press any button to reset.
Possible inadequate
water, poor flow, or
air bubbles in detected
in the heater. Spa is
shut down for 15 minutes.
Check water level in spa. Refill if
necessary. If water level is okay, make
sure the pump(s) have been primed.
Press any button to reset, or this message
will automatically reset within 15 minutes.
If problem persists, contact your dealer
or service organization.
Inadequate water
detected in heater.
(Displays on third
occurrence of “ ”
message.) Spa is
shut down.
Follow action required for “ ”
message. Spa will not automatically
reset. Press any button to reset.
Warning! Shock Hazard! No User Serviceable Parts. Do not attempt service of this
control system. Contact your dealer or service organization for assistance. Follow all
owner’s manual power connection instructions. Installation must be performed by
a licensed electrician and all grounding connections must be properly installed.
31
FUSION DOCKING STATION
Warning: Never remain in your spa longer than 15 minutes per session when
the water temperature is above 98˚F. If you wish to spend more time in your spa,
whether enjoying music, or just lounging, be sure to keep the spa water at or
below body temperature (98.6˚F).
*Please refer to your stereo Owner’s Manual for specific operations.
Optional Stereo Docking Station
Your spa is equipped with an iPod™ docking station that will allow you to listen to
personal selections through the audio system of the spa. This audio system also has an
FM only radio receiver that can be used to listen to local FM broadcasts. Due to varying signal conditions the FM radio reception may be limited.
The docking station is compatible with the following iPod™ products Nano™ 3G
4G 8G, iPod Touch™ 8G 16G, iPod Classic™ 80G 160G, and iPod™ 5G 30G 60G 80G.
Master Spas, Inc. does not guarantee compatibility with all iPod™ products due to
software changes and upgrades.
The wireless remote provided with the spa is water resistant, but should never be left
in the spa when not in use.
RF Remote Control Synchronizing
Each docking station comes with a matching wireless remote control. From time to
time it may be necessary to synchronize the remote to the docking station.
A. P
ress and hold the (play/pause) button on the remote control and then press the
power button simultaneously for 2 seconds. The LCD will display “PAIR”.
B. T
urn on the docking station by pressing the power button on the station within 10
seconds after the remote displays “PAIR”. A red light will turn on under the power
button to indicate the unit is turned on.
C. O
nce the synchronizing is complete, the LCD will return to the original screen setting.
If your music player is not an iPod, ™, you will only be able to use the volume and power control on the remote control.
In order to prolong remote battery life the LCD will shut off in 10 seconds if no other button is pressed. To turn remote
back on press power once and then press the command desired.
32
FUSION DOCKING STATION
CAUTION – Risk of Electric Shock. Do not leave compartment door open.
CAUTION – Risk of Electric Shock. Replace components only with identical
components; and
Do not operate the Audio / Video controls while inside the spa.
WARNING – Prevent Electrocution. Do not connect any auxiliary
components (for example cable, additional speakers, headphones, additional
Audio / Video components, etc.) to the system.
NOTE: These units are not provided with an outdoor antennae; when provided, it
should be installed in accordance with article 810 of the National Electrical Code,
ANSI / NFPA 70.
NOTE: Do not service this product yourself as opening or removing covers may
expose you to dangerous voltage or other risk of injury. Refer all servicing to
qualified service personnel.
NOTE: When the power supply connections or or power supply cord(s) are
damaged; if water is entering the Audio / Video compartment or any electrical
equipment area; if the protective shields or barriers are showing signs of
deterioration; or if there are signs of other potential damage to the unit,
turn off the unit and refer servicing to a qualified service personnel.
NOTE: This unit should be subjected to periodic routine maintenance
(for example, once every 3 months) to make sure that the unit is
operating correctly.
33
SPA TROUBLE-SHOOTING GUIDE
NOTHING ON THE SPA OPERATES1.) C
heck the control panel display for any messages. If there is a message, refer to the diagnostic section. There you will find the meaning of the
message and what action is to be taken.
2.) If there is no message on your control panel, check and reset the GFCI and
house breaker.
*The GFCI should be located in a weather proof box
close to the spa, but no closer than 5 ft.
If the spa does not respond, contact your local service company.
PUMP(S) DO NOT OPERATE 1.) P
ress the “Jets” button on your control panel.
If you hear the pumps trying to operate:
A. Pump may need to be primed. See page 16.
If you do not hear anything from the pump, contact your local service
company.
POOR JET PERFORMANCE
1.) Make sure pump is operating
2.) Check that the water level is adequate (up to minimum safe water level side)
3.) Make sure the jets are open.
4.) Check for dirty filter. Clean if necessary.
34
SPA TROUBLE-SHOOTING GUIDE
SPA NOT HEATING
* If the spas heater has failed, the majority of the time it will trip the
GFCI breaker. If the spa is not heating and has not tripped the breaker,
please follow these steps:
1.) C
heck the control panel for diagnostic messages. Refer to spa diagnostic
message area in previous sections.
Follow steps to alleviate message.
2.) Check water set temperature at control panel.
3.) Check for dirty filter. Clean if necessary.
4.) Check “heat mode” the spa is set in. Spa should be in standard mode.
5.) C
heck the control panel for heater light indicator. If the light is on, the spa
should be heating. Wait a reasonable amount of time (approximately 1 hour)
to see if the water temperature is changing.
6.) Check to make sure that the pump is primed.
7.) Reset power to the spa at GFCI breaker.
8.) If spa is still not heating, contact your dealer for service.
GFCI IS TRIPPING
The Ground Fault Circuit Interrupter (GFCI) is required,
by NEC code (National Electrician Code), for your
protection. The tripping of the GFCI may be caused
by a component on the spa or by an electrical problem.
Such electrical problems include, but are not limited to,
a faulty GFCI breaker, power fluctuations, or a miswire.
It may be necessary to contact an electrician if your
local dealer recommends doing so.
35
REGULAR MAINTENANCE PROCEDURES
Note: These are areas that will require the spa owner to perform routine
maintenance. These are not areas covered under the warranty of the spa.
CLEANING JETS
The majority of jets in your spa can individually be
turned on/off. If any of these jets become hard to
turn, it will be necessary to remove the jet to clean it as grit/sand and mineral deposit may be present.
Jets are removed by turning the collar and then pulling out the jet. Some jets may not be removable
depending on model.
To Clean Jets
Place the jet(s) in a bucket, fully immerse in white vinegar. Let the jet(s) soak overnight and then rinse with water. Reinstall the jet(s). It may also be necessary
to clean the grit/deposit from the white jet body using an old toothbrush.
DRAINING YOUR SPA
The drain is located behind the front panel on the far
right side, grasp the hose bib cap and turn it counter
clockwise. Attach a garden hose, if desired. Turn the black
knob on the side of the valve a quarter turn. Draining
times may vary by model using the external hose bib.
A sump pump may also be used to drain the spa quickly.
36
REGULAR MAINTENANCE PROCEDURES
CARE OF YOUR SPA COVER
Always cover your spa when not in use. This will greatly reduce energy
consumption and will cause spa water to heat more rapidly. Water loss
and chemical usage will also be reduced.
•B
e sure to lock down all straps on cover after each use to prevent
wind damage.
•D
o not allow spa to sit uncovered in direct sunlight. This may cause damage
to exposed surfaces of spa and possible discoloration of spa fittings.
•P
eriodically hose off both sides of spa cover for maximum life of cover. Once a
month use a vinyl cleaner and conditioner on the vinyl portion of your cover.
Rinse residue off.
• Keep cover open for 15 min. after adding chemicals to prevent off gas damage.
NOTE: IF YOUR SPA IS GOING TO BE LEFT EMPTY FOR PROLONGED PERIODS,
DO NOT REPLACE COVER DIRECTLY ON SURFACE OF SPA. PLACE 2”-3” BLOCKS
BETWEEN COVER AND SPA. THIS ALLOWS FOR ADEQUATE
VENTILATION OF COVER AND SPA.
NOTE: The cover warranty is provided through the cover manufacturer and not through
Master Spas. You will need to mail the cover warranty back to the cover manufacturer.
CARE OF YOUR SPA CABINET
Your quality Polymer Skirt simply needs to be hosed off periodically.
No other maintenance is required.
FILTER CLEANING
NOTE: Never operate the spa without filter in place.
If done, damage will result to pumps and other components.
We recommend having an extra filter to install when cleaning
the filter.
1.) Turn power off to the spa.
2.) Remove any large or floating debris from the filter area.
3.) R
emove the filter. Filter should be periodically rinsed and soaked in a
cartridge cleaner. Follow cartridge cleaner instructions.
37
SPA CARE AND MAINTENANCE RECORD
DATE DATE DATE DATE DATE DATE DATE DATE
Drain & Clean Spa
Clean Filter Cartridge
Soak Filter
Cartridge in Solution
Test GFCI
Clean and Condition
Spa Cover
Miscellaneous
Service
Miscellaneous
Service
38
SPA CARE AND MAINTENANCE RECORD
DATE DATE DATE DATE DATE DATE DATE DATE DATE DATE DATE DATE
39
SPA CARE AND MAINTENANCE RECORD
DATE DATE DATE DATE DATE DATE DATE DATE DATE DATE DATE DATE
40
Legacy WhirlpoolTM is manufactured
by Master Spas, one of the world’s
leading spa manufacturers.
6927 Lincoln Parkway
Fort Wayne, IN 46804
800.860.7727 [email protected]
Master Spas reserves the right to change specifications or features without notice.
Master Spas is a manufacturer of spas and related products and we stand behind every
product we produce pursuant to those representations which are stated in our written
limited warranty. your dealer is an independent business person or company and not an
employee or agent of Master Spas, Inc. We cannot and do not accept any responsibility or
liability for any other representations, statements or contracts made by any dealer beyond
the provisions of our written limited warranty.
POP09LEGACYOM
Rev. 11/09
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Languages