Drake PS151 Power Supply User Manual

TM
Power Supply
The PS151 power supply is designed to provide power
for Drake model SCT1860, SCT2860, SCT3860, and
SCT4860 transcoders and a LBS2250 when mounted in
the model RMT150 rack mounting tray. The PS151 can
power a full tray of 10 of any mix of the transcoder models
listed above. The power supply also provides an interface between a PC or modem and the transcoders via the
RS232 DB9 connectors, providing remote programming
and monitoring capabilities.
SPECIFICATIONS
GENERAL
Power Requirements: -------------------- 100 VAC to 240 VAC
(and -10%/+10% of end limits)
Frequency: ------------------------------------------------- 47-63 Hz
AC Input Power (max), --------------------------------150 Watts
Operating Temperature Range: ------------------- 0 to +50 0C
Internally Mounted (50 mm) Axial Fan
(12 VDC @ 140 mA): -------------------------- 12 CFM (ft3/min.)
Output Voltages, PS151: +3.3 VDC @ 10.0 A, +5 VDC @
1 0.0 A, and +12 VDC @ 3.0 A
MECHANICAL
Dimensions: (WxHxD): ---4.25in. W x 3.33in. H x 10.5in. D
Weight: ------------------------------------------------------- 3.5 lbs.
CONNECTORS
RS232 Out/In: ----------- (2) Type DB-9 interface connectors
DC Output: --------------- (10) Molex 39-31-0060
(Power supply assembly employs short circuit and
overvoltage protection).
PS151 POWER SUPPLY
1INSTALLATION
Install the PS151 in the RMT150 rack tray by positioning it at the far right
side of the tray as viewed from the front panel of the RMT150. Before
pushing into the final mounting location, make sure that the two hooks
located at the bottom of the rear panel on the power supply, hook over the
back edge of the RMT150 - these will secure the rear of the supply after it
has been pushed forward into its final position. Position the supply so that
the LCD and all pushbuttons are in their proper position in the front panel
of the RMT150 and that the buttons are protruding all the way through the
panel holes. Install the two screws, that are provided with the supply,
through the holes on either side of the display opening in the RMT150
front panel and into the threads of the power supply. Tighten snuggly.
Connect the power cables between the transcoders and the power supply.
Note that each power output connector on the supply is numbered, from 1
through 10. The unit ID of the connected transcoder will be determined by
which socket on the supply its power cable is plugged into. Normally, the
leftmost transcoder, as viewed from the front panel, will be number 1 with
transcoders connected in sequence to the right. The rightmost transcoder
will thus be plugged into socket number 10 on the supply. Note that
transcoders do not have to be connected in any specific numerical order
but the above method is preferred to make it easier to identify a particular
transcoder during setup, if necessary.
Carefully route the power cable for the front mounted fans between the
power supply and the adjacent transcoder and plug the fan cable into the
socket on the rear of the supply, just above the line cord.
When all cables are connected, plug the line cord into a nominal 120 VAC
outlet.
AC Power Cord: --------- 54" with USA, 3 prong, 120 V plug
Safety Approvals:
ANSI/UL 60065, 7th ed, 6/30/04 and
CAN/CSA-C22.2 No. 60065:03 (04/03)
REAR PANEL CONNECTIONS
1. AC Input - The power supply accepts standard 100 to
240 VAC, 50/60 Hz inputs (and -10%/+10% of that voltage
range). A 120 V, USA standard cord is supplied.
2. DC Output - The polarized connectors provide 10 sets
of output connections for the compatible transcoder units.
3. RS232 Remote Control Interface - If the SCT
system transcoders are to be controlled from a PC via the
RS232 interface, the serial port cable from the PC should
be connected to the 'RS232 IN' connector on the supply.
The 'RS232 OUT' connector is used to connect to the
'RS232 IN' port on another PS150/151 or to a PS100 if
additional transcoders are to be controlled. This process
may be repeated until a maximum of 7 PS150/151s (70
transcoders max.) are connected. In addition, up to 63
SCT860s could also be controlled by the same connection if PS100s are also daisy changed in this connection.
INSTALLING THE PC SOFTWARE FOR THE
DRAKE DIGITAL HEADEND CONTROL PROGRAM
To install the control software, place the CDROM in the PC CDROM tray. The
auto run routine should produce a menu providing three options:
1) Install Digital Headend Control Program.
2) View various instruction manuals.
3) Install Adobe Acrobat Reader.
To install the control software, choose the “Install Digital Headend Control
Program” option. If the CDROM does not start automatically, Click on the "My
Computer" icon on your PC desktop, then click on the CDROM drive icon. To
install the control program, click on the setup.exe file on the CDROM. Follow the
prompts and when the program has been installed successfully, the "R. L.
DRAKE DIGITAL HEADEND CONTROL PROGRAM" icon will appear on the PC
desktop.
■
■ If you have Acrobat Reader installed on your system, you may view and/or
print the detailed program Instruction Manual by selecting option 2 from the auto
run menu, or by clicking on the Instruction Manual.pdf file on the CDROM. If
Acrobat Reader is not installed on your system, select option 3 from the auto run
menu or click on the rs405eng.exe file on the CDROM to install a complimentary
copy.
®
R.L. DRAKE HOLDINGS LLC
710 Pleasant Valley Drive
Springboro, Ohio 45066. USA
Customer Service and Parts Telephone: +1 (937) 746-6990
Telefax: +1 (937) 806-1510
Web Site: http://www.rldrake.com
TM is a trademark of the R.L. Drake Holdings LLC
© Copyright 2012 R.L. Drake Holdings LLC. P/N: 651231100
Printed in China.
Rev: 20121019
1002390
2
Warranty
Three Year Limited Warranty
R.L. DRAKE HOLDINGS LLC warrants to the original purchaser this product shall be free from defects in material
or workmanship for three (3) years from the date of original purchase.
During the warranty period R.L. DRAKE HOLDINGS LLC or an authorized Drake service facility will provide,
free of charge, both parts and labor necessary to correct defects in material and workmanship. At its option, R.L.
DRAKE HOLDINGS LLC may replace a defective unit.
To obtain such a warranty service, the original purchaser must:
1. Retain invoice or original proof of purchase to establish the start of the warranty period.
2. Notify R.L. DRAKE HOLDINGS LLC or the nearest authorized service facility, as soon as possible after
discovery of a possible defect, of:
a) the model and serial number,
b) the identity of the seller and the approximate date of purchase; and
c) A detailed description of the problem, including details on the electrical connection to associated
equipment and the list of such equipment.
3. Deliver the product to R.L. DRAKE HOLDINGS LLC or the nearest authorized service facility, or ship
the same in its original container or equivalent, fully insured and shipping charges prepaid.
Correct maintenance, repair, and use are important to obtain proper performance from this product. Therefore
carefully read the Instruction Manual. This warranty does not apply to any defect that R.L. DRAKE HOLDINGS
LLC determines is due to:
1. Improper maintenance or repair, including the installation of parts or accessories that do not conform
to the quality and specifications of the original parts.
2. Misuse, abuse, neglect or improper installation.
3. Accidental or intentional damage.
All implied warranties, if any, including warranties of merchantability and fitness for a particular purpose, terminate
three (3) years from the date of the original purchase.
The foregoing constitutes R.L. DRAKE HOLDINGS LLC'S entire obligation with respect to this product, and the
original purchaser shall have no other remedy and no claim for incidental or consequential damages, losses or
expenses. Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusions
or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
This warranty shall be construed under the laws of Ohio.
For Service, contact:
R.L. DRAKE HOLDINGS LLC
710 Pleasant Valley Drive
Springboro, Ohio 45066. USA
Customer Service and Parts Telephone: +1 (937) 746-6990
Telefax: +1 (937) 806-1510
Web Site: http://www.rldrake.com