Voltek CT200 1880 Four Way Camera Switcher Instructions
Below you will find brief information for Four Way Camera Switcher CT200 1880. The Four Way Camera Switcher CT200 1880 allows you to connect up to four Voltek cameras to your TV or VCR. It has an auto facility that automatically switches between the cameras every four seconds. This device also has an adjustable switching time, allowing you to change the time between switches. The switcher also has a manual control feature, allowing you to select a specific camera to view.
advertisement
Setting the Roll Time
The AUTO switching time is factory set to 4 seconds. To change the switching time:
Press and hold both the AUTO and MANUAL button for the length of time you wish to set for the new time. i.e. if you want a switching time of 12 seconds, hold both buttons for 12 seconds.
The LED will illuminate amber while you are changing the switching time and a bleep will be heard from the TV set once every second.
The maximum switching time that can be set is 30 seconds.
ALARM OUTPUT
In the event of a movement being detected by a Voltek PIR camera the LED on the front of the unit will change to amber and the alarm output on the rear of the unit provides a negative trigger.
CONNECTING A RELAY
WARRANTY
This product has a 1 year parts and labour warranty.
HELPLINE
Please telephone 09066 191 133* should you have any questions regarding the use or installation of this product.
SPECIFICATION
Operating voltage
Current consumption
Operating temperature
Alarm Output
Weatherproofing
Size (excludes cables)
Total package weight
Carton size
12V dc nominal
20mA
-10ºC - +40ºC
0 V trigger max 60mA
IP30 (indoor use only)
158mm (W) x 35mm (H) x 129mm (D)
0.23Kg
180mm (w) x 50mm (H) x 150mm (D)
Churchill Way, Lomeshaye Ind Est. Nelson. Lancashire. BB9 6RT
Tel (01282) 695 500 Fax (01282) 695 511 International (+44 1282)
Email: [email protected] Website www.voltek.co.uk
*Helpline calls cost 60p/minute. Open 9am to 5pm, Mon to Fri.
Voltek reserves the right to change any product or
specification without notice (c) 2002
INSTALLATION
CT200 / 1880
Four Way Camera Switcher
Thankyou for purchasing the Four Way Camera Switcher. Please read these instructions thoroughly before starting the installation.
PRODUCT FEATURES
• Connect to up to four Voltek cameras to the scart socket of your TV or VCR.
• Compatible with the CT210 TV Modulator, CT220 VCR Activator & CT230
Time & Date Generator.
• 12V dc operating voltage for simple and safe wiring.
• Auto facility allowing the picture to automatically switch between the cameras.
• Adjustable switching time.
• Manual control of camera’s using simple push buttons.
• Picture priority feature shows camera of interest when movement is
detected by a camera with a PIR sensor.
• Alarm output trigger
CONTENTS
Please check & and familiarise yourself with all the parts before proceeding with the installation.
• Four way camera switcher.
• Scart plug connecting lead.
• Alarm output connector
INSTRUCTIONS
INSTALLATION
CONNECTION METHOD 1
Standard CT200 connections
Before connecting any cameras to the CT200
4 way switcher make sure that all camera power supplys have been disconnected from the mains supply. In the event of later camera additions again make sure that all power supplys have been disconnected from the main supply before connecting the additional camera / cameras to the CT200 4 way switcher.
CONNECTION METHOD 3
Connecting a CT220 VCR controller and CT230 time & date generator
Please note the keypad shown in all 3 diagrams is provided with all Voltek PIR cameras.
If you are using cameras without PIR’s the keypad is not required.
CONNECTION METHOD 2
Connecting a CT220 VCR controller or CT230 time & date generator
OPERATING THE SWITCHER
AUTO Mode
When power is first applied, the unit will be in the Auto mode, automatically switching from one camera to the next every four seconds. If you leave AUTO mode and wish to return simply press the button labelled AUTO. The green LED will be illuminated to indicate AUTO mode.
MANUAL
To manually select a camera, press the MANUAL button. Each press will switch to the next camera picture. The LED will illuminate red to indicate you are in MANUAL mode.
advertisement
Key Features
- Connect up to four cameras
- Auto switching
- Adjustable switching time
- Manual control
- Picture priority
- Alarm output
Frequently Answers and Questions
What is the maximum switching time that can be set on the Four Way Camera Switcher CT200 1880?
How do I manually select a camera on the Four Way Camera Switcher CT200 1880?
What is the alarm output on the Four Way Camera Switcher CT200 1880 used for?
Related manuals
advertisement
