BOLLARD INSTALLATION INSTRUCTIONS

BOLLARD INSTALLATION INSTRUCTIONS
BOLLARD INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [email protected]
ROUND BOLLARD
SQUARE BOLLARD
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
RAB fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding
is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A
PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING: Make certain power is OFF before installing or maintaining fixture. No user serviceable parts inside.
LOCATION
CAUTION: Before mounting, make sure to align Bollard
Base in the orientation that will result in the desired Bollard
Fixture orientation.
1. The Bollard should be mounted to a firm level surface.
2. Anchor bolts may be used in new concrete installations.
Use the template provided.
3. For all other applications use anchors suitable for the
mounting surface.
ANCHOR BOLTS INSTALLATION
CAUTION: Install according to all applicable local codes.
Install four Anchor Bolts in concrete foundation (by others)
using the template provided. Bollard Base may also be used
as the template. Bolt threads should protrude from concrete.
BOLLARD BASE
1. Place the Bollard Base over Anchor Bolts.
2. Loosely tighten the Washers, Lock washers and Nuts
provided. Level the Bollard Base with provided
Leveling screws. Tighten all nuts and screws.
3. Be sure supply leads extend far enough to make fixture
connections. Make the wiring connections with UL approved connectors.
4. Slide the Bollard over on Bollard Base lined up with the
grooves. Be sure to check the LED position on the Bollard.
5. Use the four set screws to secure the Bollard to the
Bollard Base.
Set Screws
Bollard
Base
Nuts
Lockwasher
Washer
Anchor
Bolts
Bollard
Base
Anchor
Bolts
Leveling
Screws
Concrete
Conduit
BOLLARD INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [email protected]
CLEANING & MAINTENANCE
CAUTION: Be sure fixture temperature is cool enough to
touch. Do not clean or maintain while fixture is
energized.
1. Clean lens with non-abrasive cleaning solution
WIRING
Universal driver permits 120V to 277V, 50 or 60Hz.
1. Connect the bare copper Ground wire from fixture to
supply ground.
2. Connect the black fixture lead to the (+) LINE
supply lead.
2. Do not open fixture to clean the LED.
TROUBLESHOOTING
1. Check that the line voltage at fixture is correct. Refer to
wiring directions.
3. Connect the white fixture lead to the (-) COMMON
supply lead.
(+)LINE
BLACK
(-)COMMON
WHITE
2. Is the fixture grounded properly?
ACCESSORIES
Bollard base Retro kit:
Suffix “Y” =
Suffix “N” =
GROUND
BOLBASE24 RETRO
LIGHT
FIXTURE
GROUND
Warm 3000K LED
Neutral 4000K LED,
BLED24 Square Bollard 24W Cool LED
BLEDR24 Round Bollard 24W Cool LED
BOLLARD Round: US pat. D675,766, CA Pat. pending, CN
ZL201230350184.6, MX pat. pending, TX: pat.pending
BOLLARD Square:.US pat. D675,767, CA Pat. pending, CN
ZL201230350185.0, MX pat. pending, TX: pat.pending
Note: These instructions do not cover all details or variations in
equipment nor do they provide for every possible situation during
installation, operation or maintenance.
Easy Installation & Product Help
©2014 RAB LIGHTING Inc.
Northvale, New Jersey 07647 USA
BOLLARD IN 0814
Tech Help Line
Call our experts 888 RAB-1000
rabweb.com
Visit our website for product info
email
Answered promptly [email protected]
BOLLARD INSTALLATION INSTRUCTIONS
Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.
Call the Marketing Department at 888-RAB-1000 or email: [email protected]
ANCHOR BOLT TEMPLATE FOR BLED BOLLARD
Drawing not to scale. Use the actual mounting plate as your template.
24º
45º
45.0°
Ø 2.45”
60.02mm
OPENING FOR
CONDUIT
Ø 3.75”
95.25mm
BOLT
CIRCLE
DIA
Ø 5.17”
131.3mm
11.75º
Ø 2.45”
60.02mm
OPENING FOR
CONDUIT
Ø 3.75”
95.25mm
BOLT CIRCLE
DIA
5.16”
131mm
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement