Zipato ZBMPOWERV1 Zipabox Power Module Installation ()

Zipato ZBMPOWERV1 Zipabox Power Module Installation ()
b) join Power module and Backup module together until gap
between them is completely closed;
Top left
angle
TESTING
1 | Battery in Backup module comes charged
2 | When Backup module is first time connected to Zipabox upper
LED is red indicating battery is discharging
3 | When ZipaBox is connected back to power supply upper LED will
become green
4 | When battery is charging lower LED is blue
ZIPABOX
POWER MODULE
REPARING
QUICK INSTALLATION GUIDE
v1.0
Do not attempt to repair this product.
There are no user-serviceable parts inside.
c) put Backup module (together with Power module attached) back
into Slot 1 of Zipabox;
TRADEMARKS
Although Zipato has attempted to ensure the accuracy of the
content of this manual, it is possible that this document may
contain technical inaccuracies, typographical, or other errors.
Zipato assumes no liability for any error in this publication, and for
damages, whether direct, indirect, incidental, and consequential
or otherwise, that may result from such error, including, but not
limited to loss of data or profits. Zipato provides this publication
“as is” without warranty of any kind, either express or implied,
including, but not limited to implied warranties of merchantability
or fitness for a particular purpose. The published information in
the manual is subject to change without notice. Zipato reserves
the right to make changes in the product design, layout, and driver
revisions without notification to its users. This version of the
Installation guide supersedes all previous versions.
ELECTROMAGNETIC COMPATIBILITY
In proper state and when operated properly, the product complies
with all the requirements in respect of interference radiation
according to EN 301 489-17, EN 301 489-1 and EN 300 328. The
connections conducting HF signals must neither be manipulated
nor damaged.
TAKE CARE OF YOUR SAFETY
Display extreme caution when using ladders or steps, please
follow manufacturer’s instructions. Be careful when using hand
and power tools and follow the manufacturer’s guidelines when
using them. Take care that the correct tools are used. Wear
goggles or protective clothing where required.
DANGER
RISK OF ELECTROCUTION
All work on the device should only be carried out by trained and
skilled electricians. Observe the country-specific regulations.
CAUTION
The connected devices and the flush-mounted receiver can
become damaged if devices are operated that do not correspond
to the technical specifications (see technical data).
DANGER
RISK OF FATAL INJURY FROM ELECTRIC CURRENT.
The device has no basic insulation and must therefore be installed
in a way that protects against accidental contact.
WATER-RESISTANCE
This product is not water-resistant. Keep it dry.
Moisture will corrode the inner electronics.
Zipato and the Zipato logo are registered Trademarks. All
other product names mentioned herein may be trademarks or
registered trademarks of their respective companies.
NOTICE
INSTALLATION/MOUNTING
Mount together with Zipabox on DIN rail.
CLEANING
Use a dry cloth to clean this product. Do not use harsh chemicals,
cleaning solvents or strong detergents.
INTRODUCTION
COMPATIBILITY
This Expansion Module is designed to work only with Zipabox with
software version 0.9.962 or later.
Bottom right
angle
HANDLING
Do not drop, knock or shake the module. Rough handling can break
internal circuit boards and connectors.
ENVIRONMENT
Do not expose the module to excessive heat or cold, as it can damage
or shorten the life of electronic circuit boards.
If possible, dispose this module at a recycling center.
Do not dispose of this module with the household waste.
IF YOU DO NOT HAVE BACKUP MODULE:
TECHNICAL MANUALS
TECHNICAL DETAILS
POWER SUPPLY
OPERATING TEMPERATURE
OPERATING HUMIDITY
DIMENSIONS
WEIGHT
POWER
a) align connector of Zipabox Power Module to expansion Slot 1 of
Zipabox;
Fom Zipabox
-10° ~ +40° C
5 ~ 95% RH
55 x 87 x 46 mm
155g
230V AC, 0.4A
Top view
Bottom view
UNPACKING
Zipabox Power Module consists of:
1x Expansion Module
b) join Power module and Zipabox together until gap between them
is completely closed;
CONNECTING DEVICE
1 | Disconnect Zipabox from power;
2 | Remove all modules from Slot 1;
3 | Disconnect all modules from Backup module (if you have one);
IF YOU HAVE BACKUP MODULE:
a) align connector of Zipabox Power Module to expansion slot of
Backup module;
Front view
DANGER
RISK OF FATAL INJURY FROM ELECTRIC CURRENT.
When installing a wall plate, the distance between the cover’s fixing
brackets or screws and the connections of the flush - mounted
MicroModule Switch Single must be at least 4 mm once installed.
If the distance is less than 4 mm, a deeper installation box must
be used. The fixing brackets or screws of the cover must not press
against the housing. Only insulated tools may be used for operation
on the device, e.g. an insulated phase tester.
we make every home smart
6 | If you had any other module in Slot 1 connect it back to Power
module in a same way;
7 | Connect 230V AC power to Power module;
8 | Connecting and disconnecting of Power module requires trained
professional electrician and is done as part of electric installation
of a home.
www.zipato.com
we make every home smart
www.zipato.com
ZIPABOX
POWER MODULE
QUICK INSTALLATION GUIDE
v1.0
SUPPORTING COMMAND CLASSES
BASIC TYPE
GENERIC TYPE
SPECIFIC TYPE
LISTENING
BASIC_TYPE_ROUTING_SLAVE GENERIC
GENERIC_TYPE_SWITCH_BINARY
SPECIFIC_TYPE_NOT_USED
TRUE, Z-Wave Lib: 4.51
Class: 0x26 COMMAND_CLASS_SWITCH_BINARY
Class: 0x27 COMMAND_CLASS_SWITCH_ALL
Class: 0x72 COMMAND_CLASS_MANUFACTURER_SPECIFIC
Class: 0x86 COMMAND_CLASS_VERSION
Class: 0x85 COMMAND_CLASS_ASSOCIATION
Class: 0x70 COMMAND_CLASS_MULTI_CHANNEL_V2
Class: 0x2B COMMAND_CLASS_SCENE_ACTIVATION
Class: 0x2C COMMAND_CLASS_SCENE_ACTUATOR_CONF
TECHNICAL SUPPORT
Having trouble installing your new product?
Zipato’s website contains the latest user documentation and
software updates for Zipato products and services.
www.zipato.com
CALL SUPPORT
CONTACT LINE
+ 385 1 4004 404
(Mon-Fri) 9.00am-06.00
LIMITED PRODUCT WARRANTY
GENERAL TERMS
Nothing in this Limited Product Warranty affects your statutory
rights as a consumer.
The Limited Product Warranty set forth below is given by Tri plus
grupa d.o.o. (Europe) (herein referred to as “ZIPATO”). This Limited
Product Warranty is only effective upon presentation of the proof
of purchase. Upon further request by ZIPATO, this warranty card
has to be presented, too.
EXCEPT AS EXPRESSLY SET FORTH IN THIS LIMITED WARRANTY,
ZIPATO MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. ZIPATO EXPRESSLY
DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED
WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED
BY LAW ARE LIMITED IN DURATION TO THE LIMITED WARRANTY
PERIOD. TO THE EXTENT ALLOWED BY LOCAL LAW, THE
REMEDIES IN THIS WARRANTY STATEMENT ARE CUSTOMER’S
SOLE AND EXCLUSIVE REMEDIES AGAINST ZIPATO. THEY DO
NOT, HOWEVER, AFFECT OR RESTRICT THE RIGHTS YOU HAVE
AGAINST THE BUSINESS YOU BOUGHT A ZIPATO PRODUCT FROM.
IN NO EVENT WILL ZIPATO BE LIABLE FOR LOSS OF DATA OR FOR
INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL (INCLUDING
LOST PROFIT OR DATA), OR OTHER DAMAGE, WHETHER BASED IN
CONTRACT, TORT, OR OTHERWISE. HOWEVER, NOTHING IN THIS
AGREEMENT LIMITS ZIPATO’S LIABILITY TO YOU (I) IN THE EVENT
we make every home smart
OF DEATH OR PERSONAL INJURY TO THE EXTENT RESULTING
FROM ZIPATO’S NEGLIGENCE, OR (II) TO THE EXTENT RESULTING
FROM ANY FRAUDULENT MISREPRESENTATION ON THE PART
OF ZIPATO, OR (III) TO THE EXTENT ARISING UNDER PART 1
OF THE CONSUMER PROTECTION ACT 1987 OF THE UNITED
KINGDOM. SOME STATES OR COUNTRIES DO NOT ALLOW: (1) A
DISCLAIMER OF IMPLIED WARRANTIES; (2) A LIMITATION ON HOW
LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION; OR
(3) LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES
FOR CONSUMER PRODUCTS. IN SUCH STATES OR COUNTRIES,
SOME EXCLUSIONS OR LIMITATIONS OF THIS LIMITED WARRANTY
MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS
THAT MAY VARY FROM STATE TO STATE OR FROM COUNTRY TO
COUNTRY. YOU ARE ADVISED TO CONSULT APPLICABLE STATE OR
COUNTRY LAWS FOR A FULL DETERMINATION OF YOUR RIGHTS.
This Limited Product Warranty applies to ZIPATO branded hardware
products (collectively referred to as “ZIPATO Hardware Products”)
sold by ZIPATO (Europe), its European subsidiaries, affiliates,
authorized resellers, or country distributors (collectively referred to
as “ZIPATO Resellers”) with this Limited Product Warranty.
The term “ZIPATO Hardware Product” is limited to the hardware
components and all its internal components including firmware. The
term “ZIPATO Hardware Product” DOES NOT include any software
applications or programs.
GEOGRAPHICAL SCOPE OF THE LIMITED
PRODUCT WARRANTY
This Limited Product Warranty is applicable to Hardware Products
sold by Zipato Resellers in all countries listed at the beginning of
this document under the heading “Countries in which this ZIPATO
Limited Product Warranty applies”. The Limited Product Warranty
will be honored in any country where ZIPATO or its authorized service
providers offer warranty service subject to the terms and conditions
set forth in this Limited Product Warranty. However, warranty
service availability and response times may vary from country to
country and may also be subject to registration requirements.
LIMITATION OF PRODUCT WARRANTY
ZIPATO warrants that the products described below under
normal use are free from material defects in materials and
workmanship during the Limited Product Warranty Period set
forth below (“Limited Product Warranty Period”), if the product is
used and serviced in accordance with the user manual and other
documentation provided to the purchaser at the time of purchase
(or as amended from time to time). ZIPATO does not warrant that
the products will operate uninterrupted or error-free or that all
deficiencies, errors, defects or non-conformities will be corrected.
This warranty shall not apply to problems resulting from: (a)
unauthorized alterations or attachments; (b) negligence, abuse
or misuse, including failure to operate the product in accordance
with specifications or interface requirements; (c) improper
handling; (d) failure of goods or services not obtained from ZIPATO
or not subject to a then-effective ZIPATO warranty or maintenance
agreement; (e) improper use or storage; or (f) fire, water, acts of
God or other catastrophic events. This warranty shall also not
apply to any particular product if any ZIPATO serial number has
been removed or defaced in any way.
ZIPATO IS NOT RESPONSIBLE FOR DAMAGE THAT OCCURS AS A
RESULT OF YOUR FAILURE TO FOLLOW THE INSTRUCTIONS FOR
THE ZIPATO HARDWARE PRODUCT.
LIMITED PRODUCT WARRANTY PERIOD
The Limited Product Warranty Period starts on the date of
purchase from ZIPATO. Your dated sales or delivery receipt,
showing the date of purchase of the product, is your proof of the
purchase date. You may be required to provide proof of purchase
as a condition of receiving warranty service. You are entitled to
warranty service according to the terms and conditions of this
document if a repair to your ZIPATO branded hardware is required
within the Limited Product Warranty Period.
www.zipato.com
[Other than in respect of products for domestic use (in particular
those listed in the first and last boxes in the table below), this
Limited Product Warranty extends only to the original end user
purchaser of this ZIPATO Hardware Product and is not transferable
to anyone who obtains ownership of the ZIPATO Hardware Product
from the original end-user purchaser.
PRODUCT WARRANTY PERIOD TABLE
PRODUCT TYPE
Product Warranty Period
ZIPABOX POWER MODULE
One (1) year
IMPORTANT
The content of “Product Type” listed above is subject to change;
please refer to the www.zipato.com for latest update.
PERFORMANCE OF THE LIMITED
PRODUCT WARRANTY
If a product defect occurs, ZIPATO’s sole obligation shall be to
repair or replace any defective Zipato Hardware Product free of
charge provided it is returned to an Authorized ZIPATO Service
Centre during the Limited Warranty Period. Such repair or
replacement will be rendered by ZIPATO at an Authorized ZIPATO
Service Centre. All component parts or hardware products that
are replaced under this Limited Product Warranty become the
property of ZIPATO. The replacement part or product takes on the
remaining Limited Warranty Period of the replaced part or product.
The replacement product need not be new or of an identical make,
model or part; ZIPATO may in its discretion replace the defective
product (or any part thereof) with any reconditioned equivalent (or
superior) product in all material respects to the defective product.
WARRANTOR
Tri plus grupa d.o.o.
Banjavciceva 11
10 000 Zagreb
CROATIA
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
Operation is subject to the following two conditions:
1 | this device may not cause harmful interference, and
2 | this device must accept any interference received, including
interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes :
1 | l’appareil ne doit pas produire de brouillage, et
2 | l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
TELEPHONE +385 (1) 444 444 00
FACSIMILIE +44(0)208 955 9001
DECLARATION OF CONFORMITY
The Manufacturer Tri plus grupa d.o.o. hereby declares that the
product:
Zipabox Power Module (zbmpowerv1)
In accordance with the following Directive(s): EMC Directive
(2004/108/EC), Low Voltage Directive (2006/95/EC), R&TTE Directive
(1999/5/EC) is in conformity with the e applicable requirements of the
following documents:
EN 61326
IEC/EN 55011
EN 300 220-2
EN 61000-3-2
EN 61000-3-3
EN 61000-6-2
EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-8
EN 61000-4-11
EN 301 489-1-3
AS/NZS/IEC 60335-2-97
EN 60335-1
I hereby declare that the equipment named above has been
designed to comply with the relevant sections of the above
referenced specifications. The unit complies with all applicable
Essential Requirements of the Directives.
Person responsible for this declaration:
Dean Janacek, Certification Manager
30.11.2012
COPYRIGHT
© 2012 Tri plus grupa d.o.o. All Rights Reserved.
Changes or modifications not expressly approved Tri plus grupa
d.o.o. for compliance could void the user’s authority to operate the
equipment.
No part of this manual may be reproduced or transmitted in any form
without the expressed, written permission of Tri plus grupa d.o.o.
we make every home smart
www.zipato.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement