JCD3007

MOBILE CD PLAYER / RECEIVER

Installation and Operation Manual

PO WE R

M

U

TE

VOLUME

AUDIO

VOLUME

B

LO

AND

U

D

MODE

40

WATTS x 4

SCN RPT SHF

JCD3007

SCAN

EQ AS/PS

AUX

SAFETY INFORMATION

When Driving

Keep the volume lev e l Iow enough to b e aware of the surrounding.

Protect from Water

Do not expose the product directly to water, as this can cause electrical shorts, fire or other damage.

Protect from High Temperatures

Exposure to direct sunlight for an extended period of time can produce very high temperatures inside mobile unit . Give the interior a chance to cool down before starting playback.

Do not mount radio within close proximity of engine compartment.

Use the Proper Power Supply

This product is designed to operate with a 12 volt DC negative ground battery system.

Protect the Disc Mechanism

Avoid inserting any foreign objects into the disc slot. Misuse may cause malfunction or permanent damage due to the precise mechanism of this unit.

CAUTION:

THIS MOBILE CD PLAYER IS A CLASS I LASER PRODUCT. THIS UNIT USES A VISIBLE/

INVISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION IF EXPOSED

DIRECTLY. BE SURE TO OPERATE THE MOBILE CD PLAYER AS INSTRUCTED.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OR PROCEDURES OTHER

THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION

EXPOSURE.

DO NOT OPEN COVERS AND DO NOT REPAIR BY YOURSELF. PLEASE REFER

SERVICING TO A QUALIFIED TECHNICIAN.

WARNING:

•

•

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS

EQUIPMENT DIRECTLY TO WATER.

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND INTERFERENCE, USE

ONLY THE RECOMMENDED ACCESSORIES.

DISC NOTES

Compatible Disc Types

Table 1: General Disc Information

Disc Type

Audio CD

Logo

Diameter/

Playable Sides

12 cm single side

RECORDABLE REWRITABLE

JCD3007

Playback Time

74 minutes

NOTE: CD-R and CD-RW discs will not play unless the recording session is closed and the CD is finalized.

•

Disc Maintenance

A dirty or defective disc may cause sound dropouts while playing. Before playing, wipe the disc using a clean cloth, working from the center hole towards the outside edge.

Never use benzene, thinners, cleaning fluids, anti-static liquids or any other solvent.

Insert label side up.

Do not bend.

Never touch the under side of the disc.

Wipe clean from the center to the edge.

•

•

•

Be sure to use only round CDs for this unit and do not use any special shape CDs. Use of special shape CDs may cause the unit to malfunction.

Do not stick paper or tape on the disc. Do not use CDs with labels or stickers attached or that have sticky residue from removed stickers.

Do not expose discs to direct sunlight or heat sources such as hot air-ducts, or leave them in a vehicle parked in direct sunlight where there can be a considerable rise in temperature inside the vehicle.

NOTE: A disc may become scratched (although not enough to make it unusable) depending on how you handle it and other conditions in the usage environment. These scratches are not an indication of a problem with the player.

2

JCD3007

INSTALLATION

Before You Begin

1.

Disconnect Battery

Before you begin, always disconnect the battery negative terminal.

2.

Remove Transport Screws

•

•

•

•

•

•

•

•

Important Notes

Before final installation, test the wiring connections to make sure the unit is connected properly and the system works.

Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.

Consult with your nearest dealer if installation requires the drilling of holes or other modifications to your vehicle.

Install the unit where it does not interfere with driving and cannot injure passengers if there is a sudden or emergency stop.

If the installation angle exceeds 30º from horizontal, the unit might not give optimum performance.

This unit is not waterproof and is intended for interior mounting applications only.

Exterior mounting of the unit requires use of an ASA approved marine housing.

Avoid installing the unit where it will be subject to high temperatures from direct sunlight, hot air, or from a heater, or where it would be subject to excessive dust, dirt or vibration.

Be sure to remove the control panel before installing the unit.

DIN Front/Rear Mount

This unit can be property installed with either a “Front” (conventional DIN front mount) or “Rear”

(DIN rear mount installation, utilizing threaded screw holes at the sides of the unit chassis) mount. For details, refer to installation methods A and B.

DIN Front Mount (Method A)

1.

Remove the detachable front panel, if it is attached to the chassis, by pushing the

REL button.

2.

Slide the mounting sleeve off of the chassis if it has not already been removed.

If it is locked into position, use the removal keys (supplied) to disengage it. The

Dashboard

53

182

Bend Tabs

Screw Stud

removal keys are depicted in “Removing the Unit” on page 3.

3.

Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening or cause it to bend or bow. Check that there will be sufficient space behind the dashboard for the radio chassis.

4.

Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve.

With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary to firmly secure the sleeve to the dashboard.

5.

Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve.

3

6.

Follow the wiring diagram carefully and make certain all connections are secure and insulated with crimp connectors or electrical tape to ensure proper operation.

7.

After completing the wiring connections, attach the front panel and turn the unit on to confirm operation (vehicle ignition switch must be on). If the unit does not operate, recheck all wiring until the problem is corrected. Once proper operation is achieved, turn the ignition switch off and proceed with final mounting of the chassis.

8.

Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and the spring clips lock it into place.

9.

Attach one end of the perforated support strap

(supplied) to the screw stud on the rear of the chassis using the hex nut and spring washer provided. Fasten the other end of the perforated strap to a secure part of the dashboard

Dashboard

Plain Washer

Screw ( 4 x 1 2 mm)

Screw Stud

Hex Nut (5mm)

Support Strap

either above or below the radio using the screw and plain washer provided. Bend the strap, as necessary, to position it. CAUTION: The rear of the radio must be supported with the strap to prevent damage to the dashboard from the weight

Spring Washer

of the radio or improper operation due to vibration.

10. Re-attach the front panel to the chassis and test radio operation by referring to the operating instructions for the unit.

Removing the Unit

To remove the radio after installation:

1.

Insert fingers into the groove in the front of frame and pull out to remove the frame.

(When re-attaching the frame, point the side with a groove downwards and reattach.)

2.

Insert the removal keys straight back until they click, and then pull the radio out. If removal keys are inserted at an angle, they will not lock properly to release the unit.

Trim Plate Installation

Push the trim plate against the chassis until it is fitted. You must do this before you install the control panel, otherwise it can't be attached.

Dashboard

Removal Key

DIN Rear Mount (Method B)

This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some vehicles to mount the radio to the dashboard. Please consult with your local mobile stereo shop for assistance on this type of installation.

1.

Remove the existing factory radio from the dashboard or center console mounting. Save all hardware and brackets as they will be used to mount the new radio.

2.

Carefully unsnap the plastic trim ring from the front of the new radio chassis. Remove and discard the trim ring.

3.

Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio. Select a position where the screw holes of the bracket and the screw holes of the main unit are aligned (are fitted).

Tighten the screws at 2 places on each side. Do not exceed M5 x 9 MM maximum

Screws

Dashboard

screw size. Longer screws may damage components inside the chassis.

Factory

Mounting

Bracket

Hook (Remove)

4.

Wire the new radio to the vehicle as outlined in the Universal Installation instructions.

5.

Mount the new radio assembly to the dashboard or center console using the reverse procedure of step 1.

NOTE: The mounting box, outer trim ring, and half-sleeve are not used for method B installation.

Reconnect Battery

When wiring is complete, reconnect the battery negative terminal.

4

JCD3007

JCD3007

WIRING

ANTENNA

JACK

ANTENNA

EXTENDER

CABLE

GREY

LEFTFRONT

WHITE-BLACKLF-

WHITELF+

LEFTREAR

GREEN-BLACKLR-

GREENLR+

RIGHTFRONT

GREY-BLACKRF-

GREYRF+

RIGHTREAR

VIOLET-BLACKRR-

VIOLETRR+

BLUE

BLACK

PowerAntenna

Connecttopowerantennaoramplifier,

Ifnotused,tapebareendofwire.

Ground

Connecttogroundterminalorclean unpaintedmetalpartofchassis.

RED

Accessory/Ignition

Connecttoexistingradiowireorradiofuse.

5

Figure1:20PINHARNESSPINCHART

1 2 3 4 5

11 12 13 14 15

6 7 8 9 10

16 17 18 19 20

PIN

1

2

5

6

3

4

10

11

12

13

14

15

7

8

9

16

17

18

19

20

BLUE

RED

BLACK

WHITE

WIRECOLOR

GREY/BLACK

GREY

VIOLET

VIOLET/BLACK

GREEN

GREEN/BLACK

BLACK

RED

WHITE

WHITE/BLACK

FUNCTION/LABEL

RIGHTFRONTSPEAKER(

RIGHTFRONTSPEAKER(+)

RIGHTREARSPEAKER(+)

RIGHTREARSPEAKER( )

)

LEFTREARSPEAKER(+)

LEFTREARSPEAKER( )

REARPRE-AMPLIFIERLINEOUTCOMMON

RIGHTREARPRE-AMPLIFIERLINEOUT

LEFTFRONTSPEAKER(+)

LEFTFRONTSPEAKER( )

POWERANTENNA

IGNITION(ACC)

CHASSISGROUND

LEFTREARPRE-AMPLIFIERLINEOUT

BASIC OPERATION

1

4 7

PO W E R

M

U

TE

VOLUME

AUDIO

VOLUME

B

A

LO

U

D

N

D

MODE

40

WATTS x 4

SCN RPT SHF

22

2

19

JCD3007

SCAN

EQ AS/PS

AUX

3 8 6 21 5 9 10 11 12 13 14 15 16

17

18

Power On/Off (POWER)

Press the“POWER”button(1)to Turn the unit

ON or OFF.

Volume Control

Press Up ( ) Button to increase volume,

Press down ( ) button to decrease volume.

When the volume is adjusted, the volume level

is shown on the display panel as a number ranging from 00 (lowest) to 100 (highest).

Mute

Press the MUTE button (8) on the control panel to mute the audio output. “mute” will appear on the display. Press MUTE again to a restore the audio output to the previous level.

1

6

18

21

24

8

23

Mode

Press the MODE button (5) on the control panel to select a different mode of operation, as indicated on the display panel. Available modes include Radio, CD, and AUX In

(optional Auxiliary Input).

9

12

13

Auxiliary Input

1.

Connect the external signal to the “Aux In” jack (20) located on the front of the control panel.

2.

Press the MODE button to select Aux In mode.

3.

Press MODE again to cancel Aux In mode and return to previous mode.

D

TR. DN

BND

LOC

MO

PAU

1

4

SHUF

LOUD

VOL

VOL

SCN

AMS

MUT

SCN

2

5

RPT

3

S

U

TR. UP

MOD

PEQ

6

Reset System

Use a pencil or any non-metallic object to press and hold the RESET(17)

button for five seconds to reset the main unit. The unit will return to the

Factory default settings. The reset button should be activated for the

Following reasons:

20

4

19

22

5

15

16

NO FUNCTION

11

10

14

JCD3007

•

•

• initial installation of the unit when all wiring is completed function buttons do not operate error symbol on the display

Reset Back Up Memory

The unit is supports after IGN off memorize the operation set up, like last play radio station, preset store stations,etc To resume the back up memory by pressing “MODE+M1” together

Audio Menu

Press the AUDIO button (4) on the control panel to access the Audio Menu. You can navigate through the Audio Menu items by pressing the volume control button repeatedly.

Once the desired menu item appears on the display, adjust that option by turning the volume control knob within 5 seconds. The unit will automatically exit the Audio Menu after five seconds of inactivity. The following menu items can be adjusted.

Volume Level

Use the button to adjust the Volume level from “00” (lowest) to “100” (highest).

Bass Level

Use the button to adjust the Bass level range from “-10” to “+10”.

Treble Level

Use the button to adjust the Treble level range from “-10” to “+10”.

Balance

Use the button to adjust the Balance between the left and right speakers from “10L” (full left) to

“10R” (full right). “BAL L=R” represents an equal balance between the left and right speakers.

Fader

Use the button to adjust the Fader between the rear and front speakers from “10R” (full rear) to

“10F” (full front). “FAD R=F” represents an equal balance between the rear and front speakers.

Volume( )fades to rear, Volume( )fades to front.

6

JCD3007

TUNER OPERATION

M

U

TE

1

PO WE R

4

VOLUME

AUDIO

VOLUME

7

B

A

N

D

LO

U

D

MODE

40 WATTS x 4

SCN RPT SHF

JCD3007

EQ AS/PS

22

SCAN

2

AUX

19

3 8 6 21 5 9 10 11 12 13 14 15 16 18 20

Select a Band

17

Press the BAND button (21) on the control panel to change between three FM bands and one AM band. Each band stores up to six preset stations.

Tuning

Auto Seek Tuning

Press the TUNE Up button (19) or TUNE Down button (18) on the control panel for less than

three seconds to move to the next station automatically.

Manual Tuning

Press the TUNE Up button (19) or TUNE Down button (18) for more than three seconds to enter

manual tuning mode. Press the TUNE Up (19) or TUNE Down button(18) to change the radio frequency number up or down one step. The radio signal strength meter indicates the strength of the current radio station broadcast.

Best

Reception

Worst

Reception

Scan

Press the SCAN button (22) to automatically search for stations. Each available station will flash on the display for a few seconds before the next is searched. To select a “flashing” station, press the SCAN button again.

Automatically Store / Preset Scan (AS/PS)

Automatically Store

Select a band (if needed). Press AS/PS (16) on the control panel for more than three seconds to automatically select six strong stations and store them in the current band. The new stations replace any stations already stored in that band.

Preset Scan

Select a band (if needed). Press AS/PS (16) to scan stations stored in the current band. The unit will pause for ten seconds at each preset station. Press AS/PS again to stop scanning when the desired station is reached.

Preset Equalizer (EQ)

Press the EQ button (15) to select from the following preset equalizer functions: FLAT >

CLASSIC > POP M > ROCK > DSP OFF. When “DSP OFF” is selected, the EQ function is controlled by the Bass/Treble settings.

Stereo

The unit will automatically pick up an FM stereo signal, when available. When in stereo mode, the “ST” icon appears in the display. When no stereo signal is available, the unit will automatically revert to mono operation, and no icon will be displayed.

Preset Stations

Six numbered preset buttons store and recall stations for each band.

Store a Station

Select a band (if needed), then select a station. Hold a preset button (9-14) for three seconds.

The preset number will appear in the display.

Recall a Station

Select a band (if needed). Press a preset button (9-14) to select the corresponding stored station.

7

CD OPERATION

1 4 7

PO WE R

M

U

TE

VOLUME

AUDIO

VOLUME

B

A

N

D

LO

U

D

MODE

40

WATTS x 4

SCN RPT SHF

22

2

19

JCD3007

SCAN

EQ AS/PS

AUX

3 8 6 21 5 9 10 11 12 13 14 15 16 18 20

17

Insert and Eject Disc

Seconds and the unit will play the first track on the disc. Press the eject button (2) to stop disc play

And eject the disc. The unit does not have to be turned on to eject the disc.

Controlling Disc Playback

Track Select

Press the TUNE Up (19) or TUNE Down button (18) on the control panel for less than one second

To advance to the next track on the CD. The select ed track number will appear on the display.

Press and hold the TUNE Up (19) or TUNE Down button (18) for >1 second to fast forward or

Fast reverse through the disc. CD play starts when the button is released.

Play/Pause Disc Playback (1/ )

Press the 1/ button (9) to suspend disc play. Press the 1/

Play.

Intro Scan (2/SCN)

button again to resume disc sequentially. Press 2/SCN again to stop Intro Scan and resume normal play at the current track.

Repeat Play (3/RPT)

Press the 3/RPT button (11) during disc play to repeat play the current track. Press 3/RPT again

To stop repeat play.

Random Play (4/SHF)

Press the 4/SHF button (12) on the control panel during disc play to play all tracks on a CD in random, shuffled order. Press 4/SHF again to stop random play.

8

JCD3007

JCD3007

SPECIFICATIONS

CD

Signal to Noise Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 70dB

Sampling Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.1Khz

Quantization Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 bit

Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20,000H z

Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Channel (Stereo)

FM Radio

Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87.5-107.9MHz

Intermediate Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.7MHz

Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 15dB at S/N 30dB

Stereo Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25dB at 1KHz

S/N Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50dB

AM/MW

Frequency Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530-17

20KHz

Intermediate Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .450KHz

Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 45dB

S/N Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40dB

General

Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DC 11 -14.4

Grounding System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Negative Ground

Speaker Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ohms

Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40W x 4

TROUBLESHOOTING

Symptom Cause Solution

No power The vehicle’s ignition is not on

Disc cannot be loaded or ejected

The fuse is blown

Presence of CD disc inside the player

Inserting the disc in reverse direction

Compact disc is extremely dirty or disc is defective

Temperature inside the vehicle is too high

Condensation

No sound

If the power supply is properly connected to the vehicle accessory terminal, switch the ignition key to “ACC”.

Replace the fuse.

Remove the disc in the player and insert the new one.

Insert the compact disc with the label facing upward.

Clean the disc or try to play a new one.

Wait until the ambient temperature returns to normal.

Leave the player off for an hour or so, then try again.

Adjust volume to audible level.

Check wiring connections.

The operation keys do not work

Sound skips

Cannot tune to radio station, auto-seek does not work

ERROR 1

Volume is too low

Wiring is not properly connected.

Control panel not properly installed

The built-in microcomputer is not operating properly due to noise

The installation angle is more than 30 degrees.

The disc is dirty or defective.

The antenna cable is not connected.

The signals are too weak.

Mechanism Error

Reinstall control panel.

Press the RESET button.

Adjust the installation angle to less than 30 degrees.

Clean the disc and try to play again or use new disc.

Insert the antenna cable firmly.

ERROR 2 Servo Error

Select a station manually.

Press the eject button to correct the problem.

If the error code does not disappear, consult your nearest service dealer.

Press the eject button to correct the problem.

If the error code does not disappear, consult your nearest service dealer.

9

ASA Electronics Corporation www.asaelectronics.com

© 2006 ASA Electronics Corporation v.071806

JCD3007