of

of

Re:connect

M200 Mk2

Domotic Interface

Pioneer

Dominating Entertainment.

Revox of Switzerland

.

E

2.00

Introduction M200 Mk2

Attention M200 Mk2

Mozilla Firefox.lnk

The Mk2 version has a new Atmega 644 processor, which has a larger memory. Software version 2.00 can only be installed on the M200

Mk2. If you have an M200 Mk1 with the Atmega-163/ -16 processor, you can upgrade this to the current Mk2 version with the Upgrade Kit.

After updating the M209 firmware to version 2.00 or higher, we recommend completely resetting the M200 interface by pressing the

Disable

softkey on setup page #5 for several seconds, until setup page

#1 automatically appears. Please refer also to page 13 ff.

Introduction

M200 - New features

- Switching between stations

- Function overview

Installation

Connection

M51 Link IN/ OUT

RS

Trigger Input: Input A/ B

Relay A/ B

Voltage ramp 0-10V

IR-LINK

Setup Button

Setup

#1

– Trigger input

Setup

Setup

#4

– Relay

– IR Address/ Source

– Slot/ Serial Port Mode

Serial Interface

Link

RS-232

Video Controller

Connection plan with

Pioneer-TV M219

Gefen HDMI Switcher with M51

Gefen HDMI Switcher with M219

Overview Video products

Gefen HDMI Switcher 4x1/ 4x2 / 6x2

Pioneer Models (Plasma & LCD)

Setup #5 AV Assignment

Assigning audio source

Smart audio sources

Assigning video sources

#5

Setup #5 Reset Assignment

Guarantee

Included in delivery

Technical data

Wiring the M200 interface

M200 Mk2

Introduction

Introduction

Introduction

1

4

4

5

3

3

2

2

14

14

14

15

16

17

17

18-20

6-7

8

6

6

9-12

12

12

12

13

21

21

22

23

24

25

25

26

26

27

28

Introduction

M200 Pioneer

With the Re:connect M200 Pioneer, Revox offers an interface, for the intelligent control of the most widely used Pioneer plasma and LCD devices*.

The correct picture input is automatically selected at the television with the help of the interface. Additionally, the next or previous TV programme can be selected for the television, through the M218 wall-mounted keypad.

*Please observe the system requirements

New Multiroom Planer V2.00

The new Multiroom Planner doesn't just calculate the correct address assignment for the

M219 Side room amplifiers and

M217 Wall-mounted displays, it also calculates the slot addresses for the M200 series

Re:control products in the side room. Take advantage of the possibility to be able to determine in advance, all M200,

M217 and M219 addresses simply and quickly and at the same time save the information as system documentation. You will find more information about addressing the M200 in the side room, on Page 10 of this manual.

You can download the new Multiroom Planner V2.00 free-ofcharge from the download area of the Revox Homepage, under www.revox.com.

M200 Mk2

New features from software V2.00

From software version 2.00, the

M200 can be connected not only to an M51 but also to the M219

Side room amplifier.

As a result, a Pioneer television can also be controlled from an side room, using the M219 Side room amplifier. The option of connecting an M200 interface to an M219 exists with the first four

Side room amplifiers for each zone. As a result, a total of 16

Side room amplifiers can be connected with an M200 interface in a Revox Multiroom system with 4 different zones.

In the same way as with the setup of an M51, you define which video input at the Pioneer plasma TV is activated by which

M219 audio source, through the

M203 Setup module. The local inputs Local 1 – 3 at the M219 can be used for the control, as well as the audio sources of the

Multiroom Central unit.

Important advice:

If you want to use the software version 2.00, the complete Revox system must be updated to the level 2.00, or higher.

Introduction M200 Mk2

Switching between stations using the Revox wall-mounted keypad

The M200 Mk2 offers the option of selecting specific stations

Note

:

Monitor-only devices

This comfort function is only using the skip keys (

<>

) on an

M218 wall-mounted keypad, once the TV tuner has been selected.

This comfort function requires two settings: available with TV models with an integrated TV tuner. It cannot be selected in case of monitor-only devices without a TV tuner.

2

/2 TV Tuner assignment

M200 Setup #5 - Input

1

/2 Audio IN assignment

M51 in combination with M200

The sound input, e.g. TV, Aux1,

Optical, etc., of the remote device must be assigned to one of the following Remote buttons in the

Remote

menu:

•

Local

•

Local 1

•

Local 2

•

Local 3

Assignment example

M219 in combination with

M200

There is no need to make an assignment through the

Remote

menu with an M219, because its local audio inputs (Local 1-3) are always assigned to the IR commands

Local, Local 1, Local 2

and

Local 3.

Continue with point

2/

2

The second assignment affects

Setup #5

in the M200. Here, the physical audio source of the TV sound that was assigned to a

Local Remote button

in the first step, is assigned to the television's

TV Tuner

.

In the example above, the audio source

TV

calls the television tuner. As well as the Multiroom central unit sources, a side room amplifier also offers its own local

Inputs 1-3 for the

TV Tuner

assignment.

Introduction M200 Mk2

Function Overview

As well as main room operation, the new side room functionality available from software version

2.00 also allows an M200 Mk2 to be connected to an M219 Side room amplifier. You should be aware however, that not all functions are available in the side room. This is highlighted in the individual as well as in the following overview table.

Function

Relay A/B

Trigger Input A/B

Voltage Ramp 0-10 V

IR-Link Input

RS232 Control

1

only in combination with an M-

Link booster – see drawings on pages 14-16.

Re:system M51

Yes

1

;

Yes

;

Yes

;

Yes

;

Yes

;

2

Re:connect M219

Yes

No

No

Yes

Yes

2

1+2

;

†

†

;

;

Relay control through the IR remote control (Relay function:

Remote

), is only possible if the

IR Receiver, e.g. M204, M208 is directly connected to the

M200 - see drawings on pages

14-16.

Installation & Connection

Installation

The two wood screws supplied can be used for installing the

M200 Domotic Interface. As well as the four external installation holes, two lateral slotted holes are available for a flexible installation.

M200 Mk2

Connection

You will find a detailed description of the various M200 interface connection options on the following pages.

Slotted hole

∅

4 x 20 mm /

∅

15 mm

Installation hole

∅

4,2 mm

Re:system (M51, M10) resp. Re:connect

Further Re:connect products: M201, M202, etc.

RS232 seriell interface

M-Link connection activity display

Serial interface activity display

Setup button

IR input (M204, M218)

Variable voltage output (OUT 0-10V =)

Trigger input A + B (IN 5-24V =)

Relay A + B (max. 42 Volt)

1

Installation & Connection

Connection:

M200

with

M51/ M219

Socket:

M51 LINK IN

Setup:

-

M219:

Yes

;

The M200 interface is connected with the

M51 LINK

socket on the back of the M51 or the

M219

LINK

socket on the Side room amplifier, using the supplied telephone cable.

If you want to use a different cable, you should only use a

non-crossed

, 4-core telephone cable with an RJ11 plug (6P4C modular).

Max. cable length: 100 m

Max. cable resistance: 0.1 Ω /m

M200 Mk2

Connection

:

M200

with external interfaces

Socket:

M51 LINK OUT

Setup:

-

M219:

Yes

;

The M200 interface is designed for the connection of further external interfaces:

M51 operation

Currently, the following further products can be connected with the M51::

M200

M201

(2. interface)

IR interface

M202

Ethernet interface

M203

RS232 interface

M217

Display

M219 operation

With the M219, the

LINK OUT

can be used for the connection of an M217 Display.

Use a

non-crossed

, 4-core telephone cable with an RJ11 plug (6P4C modular).

Max. cable length: 100 m

Max. cable resistance: 0.1 Ω /m

2

Installation & Connection

Connection

M200

with seriell interface

Socket:

:

RS232

Setup:

# 4 – from page 11

M219:

Yes

;

The

M200

Interface can be used with other (TV) devices, which also have a serial interface.

This enables the integration of a large number of Pioneer televisions into the Revox World.

Which models are supported and how the integration is achieved, is described starting from page 11.

The M200 Interface is also suitable as an interface to domestic facility management systems such as

AMX

or

Crestron

, which have a special Revox protocol.

Even a Windows PC with the

M230

control program can be connected to the serial interface on the M200

Serial cables with a maximum length of 10 metres can be used.

M200 Mk2

Connection

:

M200

Trigger input

Socket:

INPUT A B RS232

Setup:

# 4 – from page 6

M219:

No

†

Using

INPUT A

and

INPUT B

, you can trigger specific events at the M51. This is done by applying a voltage between 5 and 24 volts (DC) to the corresponding input. There are various options that can be carried out when the input is supplied with voltage.

This function is not available in the side room through the M219 .

Control example

The switching diagram below, shows you how can activate the

Inputs A and B with two keys S1 and S2.

The voltage source is provided by

⊕ and

Θ

on the

IR-LINK

.

3

Installation & Connection

Connection:

M200

Relay output

Socket:

Relay A B

Setup:

# 2 – from page 8

M219:

Yes,

with Link Booster ;

The two changeover relays can be operated in different modes, independently of each other.

Note

:

In active operation, the relays need 18-24 VDC. However when connected to an M219 Side room amplifier or when the M51 is in standby mode, only 12 VDC is available. This means that in these cases, the relays

do not

react to a command.

Solution:

Through the deployment of the

M-Link Booster

, the power is held at a permanent 18 VDC and the relays work reliably in every operational state – see connection diagrams on pages

14-16.

Please note

The switching voltage may not exceed 42 volts.

Switching voltage:

0- 42 Volt*

Max. switching current:

4-8 A*

* dependent on load - See

Technical data

M200 Mk2

Connection:

M200

Voltage ramp

Socket:

Output

Setup:

without configuration

M219:

No

†

Using the

OUTPUT

, you can control the output voltage with the remote control M208, giving a variable voltage between 0 and 10 volts. This voltage ramp could be used, for example, to set the dimmer control of a lighting system to a desired level

Standard electronic dimmers with a controller input offer the option of adjusting the brightness between 0 and 100%.

Functions:

- On

(with memory function)

-

Off

- Increase voltage

- Decrease voltage

- 10 fixed voltage levels

L

The remote unit control file for the voltage output at the M200 is located in the

M208 Project

Manager

device library, under the heading

Revox – Revox

Domotic M200

. All deployed

RC5 codes are stored in this file .

4

Installation & Connection

Connection:

M200

with IR controller

Socket:

IR-Link

Setup:

# 3 – from page 9

M219:

Yes

;

The connection to an IR receiver or a wall-mounted remote control is done through the 3-pin, screw-fixable Phoenix plug connection.

Revox recommends the use of a

2-core screened cable (microphone cable), where the screening is used as ground. This cable may be a maximum of 30 metres in length.

Please ensure that you use the correct polarity when setting up as otherwise you might damage your equipment.

Symbols:

+

Æ Pos. voltage. 12-20V (DC)

IN

Æ

IR Signal

Æ Ground

-

Important

Relay control through the IR remote control (Relay function:

Remote

), is only possible if the IR

Receiver, e.g. M204, M208 is directly connected to the M200 through the

IR Link

- see drawings on pages 14-16.

The maximum number of IR receivers that can be switched in parallel per

M200

is

3

.

5

M200 Mk2

Configuration

Setup Button

Using the Setup key, you call up the M200 menu, which is shown in the

M51

display.

If the M200 interface is connected with an

M219

Side room amplifier, the M51 display is also used.

In the case of an

M10

installation, display is done using the M230 service program or M-Scope.

Using the Softkeys you can get to pages

#1

till

#5

.

Setup page #5 only appears if a video device has been selected on page #4 as

Serial Port Mode

.

M200 Mk2

Setup #1 –

Control Input

Function

:

Display

:

Trigger input

Control Input A/B

Connection

:

M219

:

Input A/B page 4

No

†

6

Using

INPUT A

and

INPUT B

, you can trigger specific events at the M51.

The required option can be selected from an option loop by pressing the

Input

und

Input

softkeys.

DVD/CD

Tuner

Tape

Aux 1-3

Local

TV

Video 1-6

Power On

Power Off

System Off

Mute (Toggle)*

Light Dimmer

Not Used

Configuration

DVD/CD - TV

M51 is switched on with and/or switches over to the corresponding source.

Power On:

Switches the M51 on with the last activated source.

Power Off

Switches the M51 off.

System Off

Switches the complete system off, including any side rooms.

Mute (Toggle)

This toggles the mute function of the M51 and is only possible in conjunction with the

5.1 Decoder

Module MK 2 or 3

.

Light Dimmer

Activates the voltage output dimmer function (

Output 0-10V

) with Toggle-Automatic.

Not Used

Deactivates the corresponding input.

Ö

M200 Mk2

Please note

When you are selecting the source, you should be aware that the source that has been assigned to the corresponding button in the

Remote

menu will be selected. If a source is disabled through the

Remote

menu, it will not be activated, even when it is selected in the input option.

Further information on this topic can be found in the M51 Operating Manual in the

Introduction

chapter, in the description of the

remote

function.

7

Configuration

Setup #2 – Relay

Function

:

Display

:

Relay output

Func. Relays A/B

Connection

:

M219

:

Relay page 4

Yes,

with Link

Booster

;

The two relays each offer 5 options that can be selected with the keys.

Input

and

Input

soft-

The required option can be selected from an option loop:

Remote

Open

Close

Power On/Off

TV-Lift

Please note

The switching voltage may not exceed 42 volts.

Switching voltage:

0- 42 Volt*

Max. switching current:

4-8 A*

* dependent on load -

See Technical data

M200 Mk2

Relay Functions

Remote

The relays are controlled over IR commands (M208) with

Remote

. This function is only available if a Link Booster is installed upstream of the M200.

L

M219 - Cabling

The IR Receiver must be connected directly with the M200.

See Connection plan on page

14.

Open

The relay is in idle state

Close

The relay is energised.

Power On/Off

If the M51/ M219 is switched on, the relay is energised. In standby mode, the relay is in idle state.

TV-Lift

The relay is energised dependent on a selected M51 audio source. The decision is made by the assignment of a video source to an audio source on page

#5

of the M200 Setup

This function can be used to roll out a projector screen or to activate a TV lift.

At the same time, the correct video device input can be controlled through the serial interface.

8

Configuration

Setup #3 – IR-Address

Function

Display

:

:

Connection

:

IR Address

Remote Address

-

M219:

Yes

;

The relay and dimmer functions can be controlled through the remote control and/or a connected M218 wall-mounted operating panel.

Through the selection of the

(RC5-) remote address, you can define whether the relay and dimmer functions should be operated from the remote control and the wall-mounted operator panel or whether only one of them should be accepted.

Address Transmitter

Light (30)

Local (19)

Remote control

Wall mounted remote control

Both (30+19)

Combination

L

The remote address has no relationship to the slot address, which the M200 uses to register with the M51/ M219.

9

M200 Mk2

Setup #3 – Source

Function

:

Display

:

Connection

:

IR receiver

Remote Source

inc. IR-Link - page 5

M219:

No

†

Selection of the (IR) sources that the M200 interface accepts for dimming and relay functions as data suppliers.

This M-200 only

Accepts only sources that are directly connected to the M200’s

IR Link, e.g..

MR204

or

M218

wall-mounted remote control.

All Receivers

All sources are accepted as data suppliers, e.g. also a M51 or an additional M200 interface.

This setting has no effect in the case of a side room installation with an M219.

Configuration

Setup #4 a) Slot M51

Function

:

Display

:

Addr. assignment

Slot Address

Connection

:

M219:

M51-Link – page 2

Yes

;

M51 operation – fig. page 15

If a second M200 (M203) is connected to the

M51 Link

output, a different address must be assigned through the slot selection so that both M200s don’t occupy the same slot address. This would cause errors. In the case of a double assignment, neither of the two

M200s would be shown in the M51

Version list.

Slot Address :

#11

or

#12

The two slot addresses 11 and 12 are available for selection. The following message appears (Display

:

#xx occupied)

if the selected address is already assigned:

M200 Mk2

Setup #4 b) Slot M219

M219 operation - fig. page 13

In respect of the M219, the slot address defines the assignment to the Side room amplifier. A M200 can only be connected to an Side room amplifier within the address range

x1 – x4.

10

The slot address defines which

Side room amplifier the M200 interface should communicate with. This is necessary because of the bus system, although in each case, the M200 is individually connected with the M219. Only one

M200 interface can be used per

Side room amplifier.

Address assignment : Zone 1-4

M219/ 217 M200/ M203

x 1 x 2 x 3 x 4 x 5 x 6

Ö

Ö

Ö

Ö

x

x

x

x x 7 x 8

x 1 – x 4: only M219

x 5 – x 8: M217 or M219

x 11 – x 14: only M200 / M203

Configuration

Example

In Figure A, an M200 could be connected to each of the Side room amplifiers 31 – 34. The M219 amplifiers 35 and 38 on the other hand may not be connected with an M200 interface.

Fig A. Multiroom version list / Zone 3

The figure below shows the Multiroom version list from Zone 3 for the M200 interfaces. You get to this menu by repeatedly pressing the

Zone

softkey in the sub-menu

(M51, M230 etc.) of: Setup Ö

Multiroom Ö Version

Ö Zone x

In this case, an M200 interface was assigned to the Side room amplifier with address 4, through the slot address 314. Amplifiers 1

– 3 do not have an M200.

Fig B. Multiroom version list / Zone 3

M200 Mk2

Setup #4 – RS232 Modus

Function

:

Display

:

RS232 interface

Serial Port Mode

Connection

:

M219:

RS232 – page 3

Yes

;

The function of the serial interface (

Serial Port

) can be configured for the following applications:

•

RS-232 Link

•

RS-232 Filtered

•

Gefen HDMI Switcher

4x2, 4x1

•

Gefen HDMI Switcher

6x2

•

Pioneer

PDP 5000 EX

•

Pioneer

PDP 506 FDE

•

Pioneer

PDP 506 XDE - Cable

•

Pioneer

PDP 506 XDE - DVBT

•

Pioneer

PDP 507 XA

•

Pioneer

PDP 507 XD

•

Pioneer

PDP 508 XD

•

Pioneer

PDP 607 XD

•

Pioneer

PDP 60 MXE20

•

Pioneer

PDP 615 EX

•

Pioneer

PDP LX5090H

•

Pioneer

PDP LX5090

•

Pioneer

LCD KRL-32V

•

Pioneer

LCD KRL-37V

•

Pioneer

LCD KRL-46V

•

Pioneer

KRP 500A*

•

Pioneer

KRP 600A*

* with setting PDP LX5090 H

Please take note of the important information on page 13 relating to a

complete reset

of the M200.

11

Configuration

Setup #4 – Auto Standby

Function

:

Display

:

Auto Standby

Auto Standby

Connection

:

M219:

RS232 – page 3

Yes

;

The

Auto Standby

function enables the TV to remain switched on, even in the case of selected audio sources that do not activate a video input at the

TV, e.g. the M51 radio tuner.

M200 Mk2

RS-232 Link .

Standardised serial interface

(RS232 protocol) for connection to a PC or another serial interface.

The

Auto Standby

option is only shown in the menu if a

Pioneer

model has been selected as

Serial

Port Mode

.

Auto Standby: ON

The Plasma TV switches itself

off

automatically as soon as an audio source is selected, which either cannot activate a video input, e.g.

Tuner, or which is

disabled

Auto Standby: OFF

After the Plasma TV has been switched on, it remains on

permanently

until the M51/ M219 is switched off, irrespective of which audio source is selected.

Application:

You should select this setting if you want to use the

M230

control program for PCs or if you want to access the Revox System through domestic facility management equipment such as

Crestron and AMX.

RS-232 Filtered .

Data-reduced RS232 protocol.

Only M51-specific data is transferred, so-called display and broadcast messages.

Application:

Simple controllers with low data traffic requirements.

12

Configuration

Video Controller

If a video controller for a plasma

TV was selected on page #4

Port Mode

, a second menu page,

Setup # 5

is available.

This page enables you to selectively switch on and/or between video inputs on a Pioneer TV or an HDMI Switcher from the Gefen company, dependant on the selected M51/ M219 source.

Example M200 with M51:

A SAT receiver can conveniently be integrated through the automatic selection of the video input on the TV by the M51. Its picture output is connected, for example, to the

Input-2

on the Pioneer TV, while the audio signal is connected to the

Optical

digital input on the M51.

Please also refer to the picture on the next page.

If you now select the source

SAT

(

Optical

) at the M51, the Pioneer

TV automatically transmits the

SAT receiver picture over the

Input-2

and the sound from the

SAT receiver is transmitted over the M51.

13

M200 Mk2

The convenient integration can of course also be used for the

M51’s integrated DVD player.

Please refer to the picture on the next page – Connection : Video

1).

The audio source and video input links referred to in the example are defined in Setup #5.

You will find an exact description of the links, starting from page 21.

Complete reset?

Yes

You should always carry out a complete reset with each new configuration as well as when changing to another TV model.

To do this, press the

Disable

softkey on Setup page #2 and keep it pressed, until the system automatically returns you to page 1.

No

A complete reset is

not

necessary with an assignment change within a TV model.

Configuration

Connection plan: Pioneer TV with M51

M200 Mk2

_

Adapter *

Connection plan: Pioneer TV with M219

_

Adapter *

* Adapter is model-dependent, see page 18

14

Configuration

Connection plan: HDMI switch with M51

M200 Mk2

Note

The HDMI output on the M51 is only available if the DVS module is installed.

Gefen

®

: Registered trademark of the Gefen Company/ US

15

Configuration

Connection plan: Pioneer TV with M219

M200 Mk2

16

Configuration

Gefen HDMI Switcher 4x2, 4x1

Switcher 6x2

Control software for the HDMI

Switcher from the Gefen Company (www.gefen.com)

The HDMI inputs on the HDMI switcher are activated, dependant on the M51/ M219 source. If there is no assignment, the HDMI input that was last selected remains active. Setting is done on page #5 in the M200 Setup

Product features:

- 4 HDMI inputs (4x1,4x2)

- 6 HDMI inputs (6x2)

- 1 HDMI outputs (4x1)

- 2 HDMI outputs (4x2),

whereby both outputs can be

operated in parallel

- Resolution up to 1080p

- HDCP-enabled

- Optical audio digital output

A crossed Sub-D cable (plug – plug) is required for the transmission.

Type:

Plug-Plug

For this reason, you should use the enclosed crossover adapter and gender adapter with the supplied Revox cable.

+

17

9-Pol

Pin 2

Pin 3

Pin 5

M200 Mk2

⇒

9-Pol

⇒

⇒

⇒

Pin

Pin

5

Max. cable length RS232: 10 m

Gefen products are freely available through specialist retail outlets.

Configuration

Pioneer Models:

PDP 5000 EX

PDP 506 FDE

PDP 506 XDE-C

PDP 506 XDE-DVBT

PDP 507 XA/ XD

PDP 508 XD

PDP 607 XD

PDP LX5090 H

PDP LX5090

KRP 500A*

KRP 600A*

The models listed above require a crossover serial cable, also known as a null modem cable, as the control cable between the

M200 and the Pioneer TV.

Connection type:

Plug - Socket

For this reason, you should use the enclosed crossover adapter with the supplied Revox 1:1 cable

9-Pol

Pin 5

Pin 2

Pin 3

⇒

9-Pol

⇒

⇒

⇒

Pin

Pin

2

M200 Mk2

Pioneer Models:

PDP 615 EX

PDP 60 MXE20

LCD KRL-32V

LCD KRL-37V

LCD KRL-46V

The models listed above require a normal serial 1:1 cable, as the control cable between the M200 and the television.

Connection type:

Plug - Socket

The supplied Revox 1:1 cable conforms to this configuration and can be used directly, without an adapter.

9-Pol

Pin 5

Pin 2

Pin 3

⇒

9-Pol

⇒

⇒

⇒

Pin

Pin

3

Max. cable length RS232: 10 m

* with setting PDP LX5090 H

Max. cable length RS232: 10 m

18

Configuration M200 Mk2

Activating the Pioneer RS232 interface - PLASMA

Models: PDP 506 / PDP 507

The RS232 interface must be activated in the

Integrator

menu, so that these Pioneer models can receive the commands from M200 Pioneer.

Please take note of the sequence of activation on the RS232 mode.

Under certain circumstances, the

Integrator

menu doesn’t appear the first time. If this happens, please repeat the process.

1)

Switch on / switch over the plasma television to TV mode

2)

3)

4)

5)

6)

Place the plasma television in standby mode

Press and release the

i

+

(

INFO

)

button on the Pioneer remote control .

[Point 3 is not always necessary. It depends on the manufacturing date of the Pioneer Plasma]

Press and release the

HOME MENU

button on the Pioneer remote control .

Follow this without delay, by pressing and releasing the

(Power) button

Deactivate the

SR+

mode in the

Integrator

menu that now appears. This activates the RS232 mode at the same time

7)

8)

Confirm the change by pressing the

HOME MENU

button

Switch the device off and restart

Model: PDP 508

The PDP 508 model does not have an explicit

SR+

mode within the

Integrator menu. In fact, the baud rate of the Pioneer interface can be set through the Integrator menu. The baud rate should be set to

9600

for communication with the M200.

Model: PDP 5000EX

With the PDP 5000 EX, the RS232 interface is activated in the normal user menu (HOME MENU – Setup – SR+).

Models: PDP 615EX / PDP 60MXE / PDP LX 5090 H

PDP LX 5090 / KRP 500A / KRP 600A

With these models, the RS232 interface is already activated. No further activation settings are required.

19

Configuration

Activating the Pioneer RS232 interface – LCD

M200 Mk2

Models: LCD KRL-xxV

Following the initial commissioning of a Pioneer LCD television, its serial interface (RS232) is not yet configured for control by an external device, like the M200 Pioneer in our case. The RS232 interface is only permanently activated once a one-off initialisation command is sent through the M200 interface to the LCD television. Activation is done with the following steps:

1)

2)

3)

Carry out a complete reset (see Page 13)

Make the settings as described in

"Setup #5 – AV Assignment", from Page 21.

Switch on the M51/M219 with FM Tuner. If no FM Tuner is in-

4)

5)

stalled, select a source that is not linked to a television video input in Setup #5.

Switch on the LCD television with the original remote control, using the

Power

button.

Wait until the television is ready to receive.

6)

7)

Now select a source at the M51 (or at the M219 Side room amplifier), which is linked to a television video input in Setup

#5.

The LCD television is now initialised and retains the facility to be controlled through the serial interface, even when it is switched off.

Please note:

If the television is changed, the process described above has to be repeated.

Pioneer LCD special characteristic

The LCD inputs

Input 3

and

Input 8

can only be addressed by the

M200 if there is already a signal at its input. If this is not the case, the

LCD television recognises this and ignores the control command.

20

Configuration

Setup #5 – AV Assignment

Function

:

Display

:

AV Assignment

Source

Connection

:

M219:

RS232 – page 3

Yes

;

Unknown audio sources

"Sources unknown" can still be present during the initial configuration, caused by the swap or the de-installation of modules.

M200 Mk2

1. Selecting audio source

To start with, select the M51 /

M219 audio source that later should activate a particular video input on the Pioneer television/ HDMI Switcher, using the

Source

± softkey.

Following switch-on, it can take a few seconds until the M200 interface has identified all the

M51 / M219 sources and until the

Source ”Unknown"

message disappears.

Any remaining unknown sources should be deleted by pressing the

Disable

softkey twice and then pressing the

Delete

softkey.

If too many unknown sources are present, we recommend completely resetting the M200 interface by pressing the

Disable

softkey for several seconds, until Page #1 automatically appears

.

Using the

Source+

and

Source-

softkeys, you can step forwards and backwards respectively, through a loop of audio inputs, which are currently available on the M51 / M219.

If the name of an audio source has been changed, the modified name also appears in the list.

An

“Unknown” Source

must be deleted manually. You will find more information about this in the previous section.

21

Configuration

Intelligent Audio Sources

The M200 differentiates between 3 type of audio sources:

1. Permanent sources

2. Semi-intelligent sources

3. Intelligent sources

1. Permanent sources

In the case of permanent audio sources, including for example the

Tuner

source, the television is switched on immediately with the corresponding video input that was assigned to it on Setup page #5. Manual switch-on or switch-off through the remote control is not possible.

2. Semi-intelligent sources

In the case of semi-intelligent sources, you can define through the remote control, whether the television should be switched on with the previously defined video input or not. Such sources have respectively

TV ON

and

TV OFF

function keys in the remote control menu. The semi-intelligent sources, such as the M37 Music

Server, store the last selected state.

If, for example, the video input from the

Server

was activated at the television using the remote control, the television is automatically activated next time this source is selected.

M200 Mk2

3. Intelligent sources

In the case of intelligent sources, it is a question of sources, which, dependant on setting or medium, can transmit a video signal to accompany the audio signal. An example of an intelligent source is the DVD/CD

M51 source. If there is a music

CD on the M51 drive, the television is not switched on because in this case, no video is required. If, on the other hand, a

DVD is identified, the television is switched on.

Source – Switch on

Yes/No

DVD/CD:

CD Switch on:

No

†

DVD Switch on:

Yes

;

SAT:

Radio Switch on:

No

†

TV Switch on:

Yes

;

22

Configuration

Setup #5 – AV Assignment

2. Assigning video inputs

In the second step, a video input from the television / HDMI

Switcher is assigned to the selected M51/ M219 audio source, using the

Input

±

softkey. Using the

Input

±

softkey, you can step through a loop of video inputs that are available to the television.

M200 Mk2

The following display appears, if a video input is called by one or more audio sources:

As the televisions that can be selected from have different video inputs, only those video inputs that the corresponding TV device has, are actually displayed.

The softkey

Store

appears as confirmation each time the

Input

is changed. Press

Store

if you want to save your changes.

Otherwise the original setting is retained.

Assignment example

This example shows you that, as well as the currently displayed audio source (DVD), a further audio source has also been assigned to this video input

(here

Input 2

). Using the

Source

±

softkeys, you can search for the audio source that also calls this video input.

Several audio sources are always required if, for example, the M300/M301 Video switch is used, which bundles several video sources together to one video input on the television.

23

Configuration

Setup #5 – Function

TV-Lift

Relay activation

When assigning video inputs, you define at the same time which inputs should activate the relays if the

TV-Lift

function has been selected in Setup #2. If the audio source has no assignment and remains "disabled", the relay is not activated.

When changing from a TV-Lift source (relay active) to non-TV-

Lift source, the relays are deactivated after a timeout of 20 seconds. This prevents the screen from being retracted and rolled out again unnecessarily, for example, in the case of an accidental source change.

Please refer to page 8 – Setup #2 for the configuration of the relay function.

M200 Mk2

Example:

Settings definition – Setup #5

Settings definition – Setup #2

Effects

1. Æ Setup #5

The audio source "DVD/CD" switches the Pioneer television on / over to the video input "

Input 2

" as soon as a

DVD is identified in the drive.

With a CD, the Pioneer television is or remains switched off.

Æ "Intelligent sources" See page 20.

2. Æ Setup #2

Relay A is activated.

Relay B can only be activated through the remote control.

24

Configuration

Setup #5 – Disable

Disable assignment

Using the

Disable

function, you can undo or disable the assignment of an audio source to a video input.

M200 Mk2

Reset assignment

If you want to return the settings in Setup #2 menu to the factory settings, simply press and hold the

Disable

softkey until the

Setup- #1

page appears again.

To do this, select the required audio input using the

Source ±

softkeys and then press the

Disable

softkey. The

Store

softkey then appears that you need to press to confirm your change.

This resets all input assignments and restores the factory settings.

If you don’t press

Store

, the original setting is retained.

25

Appendix

Guarantee

The guarantee period is 24 months from the date of purchase.

Your dealer should be your first contact if you need service. If he can't give you the help you need, send your M200 interface carriage free and without any accessories to your national

Sales Office.

Please supply a complete description of the problem and a full return postal address.

M200 Mk2

Included in delivery

ƒ

M200 Domotic Interface

ƒ

M51-Link cable ( 2 m )

ƒ

Serial PC cable

(1:1 - length 3 m)

(Plug-Socket)

ƒ

RS232 Crossover adapter

ƒ

Gender adapter

ƒ

Accessories (Installation)

ƒ

Manual

26

Appendix

Technical Data

M200 Mk2

Relay: A - B

Switching voltage

Max. switching current with

- Alternating current (AC):

- Direct current (DC):

INPUT: A - B

Max. input voltage.

Threshold voltage input resistance max. 42 Volt

8 Ampere (ohmic or inductive load)

8 Ampere (ohmic load)

4 Ampere (inductive load)

24 Volt (DC)

5 Volt (DC)

2 kOhm

Please ensure correct polarity

OUTPUT:

Output voltage

Max. output current.

0-10 Volt (DC)

10 mA

Please ensure correct polarity

IR-LINK:

+

Æ Positive voltage 10-20V (DC)

IN

Æ

-

Æ

Dimensions

:

Weight

IR signal

Ground (GND)

140 x 65 x 40 mm (W x H x D)

330 g

Power consumption: 36 mA (without IR receiver)

Max. cable length:

Max. cable length:

100m (M200-M51)

30m (M200- IR-receiver)

E & OE

Product subject to technical modifications.

27

Appendix

Wiring the M200 interface

M200 Mk2

28

Appendix

GERMANY

Revox GmbH, Am Krebsgraben 15, D-78048 VS-Villingen

Phone +49 7721 8704 0, Fax +49 7721 8704 29 [email protected], www.revox.de

SCHWEIZ

Revox Schweiz AG,

Wehntalerstrasse 190, CH-8105 Regensdorf

Phone +41 44 871 66 11, Fax +41 44 871 66 19 [email protected], www.revox.ch

Zentralservice

Revox GmbH, Am Krebsgraben 15, D-78048 VS-Villingen

Phone +49 7721 8704 43, Fax +49 7721 8704 49 [email protected]

M200 Mk2

Copyright by Revox GmbH, Germany.

29