User manual | 5460

Manual Index
DEMING
®
INSTALLATION, OPERATION & MAINTENANCE MANUAL
Vertical Process Pumps
Series: 5460
IMPORTANT!
A Crane Co. Company
Read all instructions in this manual before operating pump.
As a result of Crane Pumps & Systems, Inc., constant product improvement program,
product changes may occur. As such Crane Pumps & Systems reserves the right to
change product without prior written notification.
420 Third Street
Piqua, Ohio 45356
Phone: (937) 778-8947
Fax: (937) 773-7157
www.cranepumps.com
83 West Drive, Bramton
Ontario, Canada L6T 2J6
Phone: (905) 457-6223
Fax: (905) 457-2650
Form No. 120024-Rev. C
CONTENTS
SAFETY FIRST ................................................................................3
A.
GENERAL INFORMATION...............................................................4
Receiving
Storage
Service Centers
B.
BEFORE YOU BEGIN ......................................................................4
C.
INSTALLATION ................................................................................4
D.
DIRECTION OF ROTATION .............................................................4
E.
OPERATION.....................................................................................4
F.
PUMP ADJUSTMENT ......................................................................5
G.
IMPELLER ADJUSTMENT ...............................................................5
H.
DISCHARGE PIPE ...........................................................................5
I.
LUBRICATION..................................................................................5
J.
GENERAL MAINTENANCE & REPAIRS .........................................5
K.
FOR INSPECTION OR REPAIR OF LIQUID END ...........................5 - 6
L.
TO INSPECT BALL BEARINGS & SEAL OR SHAFT ......................6
M.
TO REASSEMBLE BALL BEARINGS AND SEALS .........................6 - 7
N.
ASSEMBLY OF LIQUID END ...........................................................7
O.
CHAIR BRACKET MOUNTING ........................................................7 - 8
P.
LOCATING TROUBLE .....................................................................8
CROSS-SECTION & PARTS LIST ...................................................9
WARRANTY & RETURNED GOODS ..............................................11
Other brand and product names are trademarks or registered trademarks of their respective holders.
Deming® is a registered trademark of Crane Pumps & Systems, Inc.
1996, 10/06
2
Alteration Rights Reserved
SAFETY FIRST!
Please Read This Before Installing Or Operating Pump. This
information is provided for SAFETY and to PREVENT EQUIPMENT
PROBLEMS. To help recognize this information, observe the
following symbols:
IMPORTANT! Warns about hazards that can result
in personal injury orIndicates factors concerned with
assembly, installation, operation, or maintenance which
could result in damage to the machine or equipment if
ignored.
CAUTION! Warns about hazards that can or will cause minor
personal injury or property damage if ignored. Used with symbols
below.
WARNING! Warns about hazards that can or will cause serious
personal injury, death, or major property damage if ignored. Used
with symbols below.
Hazardous fluids can
cause fire or explosions, burnes or death
could result.
Biohazard can cause
serious personal injury.
Rotating machinery
Amputation or severe
laceration can result.
CAUTION ! Do not block or restrict discharge hose, as
discharge hose may whip under pressure.
WARNING ! Do not wear loose clothing that may
become entangled in moving parts.
WARNING ! Keep clear of suction and discharge
openings. DO NOT insert fingers in pump with power
connected.
Always wear eye protection when working on pumps.
Make sure lifting handles are securely fastened each
time before lifting. DO NOT operate pump without safety
devices in place. Always replace safety devices that
have been removed during service or repair. Secure the
pump in its operating position so it can not tip over, fall
or slide.
Extremely hot - Severe
burnes can occur on contact.
Hazardous fluids can Hazardous pressure, eruptions or explosions could cause personal
injury or property damage.
Hazardous voltage can
shock, burn or cause death.
DO NOT exceed manufacturers recommendation for
maximum performance, as this could cause the motor
to overheat.
DO NOT remove cord and strain relief. DO NOT connect
conduit to pump.
Only qualified personnel should install, operate and repair
pump. Any wiring of pumps should be performed by a qualified
electrician.
WARNING ! Cable should be protected at all times to
avoid punctures, cut, bruises and abrasions. Inspect
frequently. Never handle connected power cords with
wet hands.
WARNING ! To reduce risk of electrical shock, pumps and
control panels must be properly grounded in accordance
with the National Electric Code (NEC) or the Canadian
Electrical Code (CEC) and all applicable state, province,
local codes and ordinances. Improper grounding voids
warranty.
WARNING ! To reduce risk of electrical shock, all wiring
and junction connections should be made per the NEC
or CEC and applicable state or province and local
codes. Requirements may vary depending on usage
and location.
WARNING! To reduce risk of electrical shock, always
disconnect the pump from the power source before
handling or servicing. Lock out power and tag.
WARNING! Submersible Pumps are not approved for
use in swimming pools, recreational water installations
decorative fountains or any installation where human
contact with the pumped fluid is common.
WARNING! Operation against a closed
discharge valve will cause premature bearing
and seal failure on any pump, and on end
suction and self priming pump the heat build
may cause the generation of steam with resulting dangerous
pressures. It is recommended that a high case temperature
switch or pressure relief valve be installed on the pump body.
WARNING! Products returned must be cleaned,
sanitized, or decontaminated as necessary prior to
shipment, to insure that employees will not be exposed
to health hazards in handling said material. All Applicable
Laws And Regulations Shall Apply.
Bronze/brass and bronze/brass fitted pumps may
contain lead levels higher than considered safe for
potable water systems. Lead is known to cause cancer
and birth defects or other reproductive harm. Various
government agencies have determined that leaded
copper alloys should not be used in potable water
applications. For non-leaded copper alloy materials of
construction, please contact factory.
CAUTION ! Never operate a pump with a plug-in type
power cord without a ground fault circuit interrupter.
CAUTION ! Pumps build up heat and pressure
during operation-allow time for pumps to cool
before handling or servicing.
Crane Pumps & Systems, Inc. is not responsible for
losses, injury, or death resulting from a failure to observe
these safety precautions, misuse or abuse of pumps or
equipment.
WARNING ! Do not pump hazardous materials
(flammable, caustic, etc.) unless the pump is specifically
designed and designated to handle them.
3
A - GENERAL INFORMATION
C - INSTALLATION
TO THE PURCHASER:
Congratulations! You are the owner of one of the finest
pumps on the market today. These pumps are products
engineered and manufactured of high quality components.
With years of pump building experience along with a
continuing quality assurance program combine to produce
a pump which will stand up to the toughest applications.
1.
Carefully lower the assembled pumping unit into
the tank or pit. The base plate (23) must rest evenly
at all points and must be level before it is bolted to the
foundation. Shim and grout to level the base plate.
Install foundation bolts.
2.
If motor and shaft coupling were shipped unmounted:
a. Install coupling (42) on the motor shaft and
pump shaft according to coupling manufacturer’s
recommendations.
Check local codes and requirements before installation.
Servicing should be performed by knowledgeable pump
service contractors or authorized service stations.
b.
RECEIVING:
Upon receiving the pump, it should be inspected for
damage or shortages. If damage has occurred, file a claim
immediately with the company that delivered the pump.
If the manual is removed from the crating, do not lose or
misplace.
STORAGE:
Short Term - Pumps are manufactured for efficient
performance following long inoperative periods in storage.
For best results, pumps can be retained in storage, as
factory assembled, in a dry atmosphere with constant
temperatures for up to six (6) months.
Lift the motor over the driver pedestal (81) and
carefully lower the motor until it rests on the
pedestal. Insert and tighten cap screws (219).
Complete coupling assembly and tighten coupling
setscrews.
3.
Rotate pump shaft by hand several times to be sure
that it rotates freely. If shaft binds, refer to the section
on “Pump Adjustment”.
4.
A check valve and gate valve should be installed in
the discharge piping near the pump discharge to
prevent damage to the pump due to reverse flow upon
the pump shut-down.
Connect discharge piping to the pump discharge. The
weight of the pipe and valves must be supported
so that the weight does not rest on pump discharge
connection, as this may cause misalignment. Do not
pull pipe into position with flange bolts.
Long Term - Any length of time exceeding six (6) months,
but not more than twenty four (24) months. The units
should be stored in a temperature controlled area, a roofed
over walled enclosure that provides protection from the
elements (rain, snow, wind blown dust, etc..), and whose
temperature can be maintained between +40 deg. F and
+120 deg. F. Pump should be stored in its original shipping
container and before initial start up, rotate impeller by hand
to assure seal and impeller rotate freely.
5.
Rotate shaft again by hand several times to be sure
that it rotates freely.
D - DIRECTION OF ROTATION
SERVICE CENTERS:
For the location of the nearest Deming Service Center,
check your Deming representative or Crane Pumps &
Systems Service Department in Piqua, Ohio, telephone
(937) 778-8947 or Crane Pumps & Systems Canada, Inc.,
Bramton, Ontario, (905) 457-6223.
Connect power leads to motor terminals according to
wiring diagram on the motor and to the motor control or
starter. Remove motor cap screws (219) and disengage
the shaft coupling. Jog control to test for proper pump
rotation. Standard pump rotate clockwise when looking
down on top of the motor, see rotation arrow on the pump.
If rotation is incorrect, on 3 phase current interchange the 2
main power leads at the starter and test for rotation again.
When proper rotation is established mark the power leads
to the proper starter terminals and reassemble the shaft
coupling and replace motor cap screws.
B - BEFORE YOU BEGIN
These pumps are assembled, carefully adjusted and
lubricated at the factory before shipment.
When motors are shipped unmounted or supplied by
the user, the motor and flexible shaft coupling must be
mounted on the pump at time of installation.
E - OPERATION
If pump is furnished with chair bracket for mounting
horizontal type motor, the motor shaft must be carefully
aligned with pump shaft before installing flexible shaft
coupling. See “Chair Bracket Mounting”.
Start the pump and check again for proper rotation. Pump
should operate smoothly and without vibration. If pump
vibrates, impeller adjustment may be incorrect or there
may be distortion of the pump base plate (23) or the
discharge piping. Refer to section on “Pump Adjustment”.
4
F - PUMP ADJUSTMENT
I - LUBRICATION
If after making the installation as above and the pump
shaft does not rotate freely or if there is vibration
in the pumping unit, the following adjustments are
recommended. LOCK ENTRANCE DISCONNECT
SWITCH IN THE OFF POSITION and separate the
coupling halves before proceeding.
The pump bearings (18) and (16) and the lip seals (47)
and (49) were properly lubricated at the factory before
shipment. Periods of subsequent lubrication will depend on
local conditions, hours of operation, speed, temperature,
etc.
It is recommended that the bearings and seals be
periodically inspected and lubricated. As a guide we would
recommend the following frequency.
G - IMPELLER ADJUSTMENT
An outstanding feature of this pump is the abillity to adjust
the impeller clearance to compensate for eventual wear or
to modify the design performance of the pump.
The normal clearance between the impeller vanes and
suction cover (9) or the casing (1) at the suction inlet is
.012 to .015 inches which provides optimum operating
performance. To adjust the impeller clearance, proceed as
follows:
1. Disengage flexible shaft coupling.
Pump Service
Ambient
Temperature
Lubrication
Interval
8 hours per day
high
low
6 to 8 weeks
12 weeks
24 hours per day
high
low
3 to 4 weeks
6 to 8 weeks
A lithium base grease of medium consistency with
corrosion resistant inhibiting properties must be used for
the ball bearings and the lip seals. Shell Alvania #2 or
equal is recommended.
2. Unscrew the 3 adjusting lock nuts (204) until
they are against the heads of the jackscrews
(286) then unscrew the jackscrews several turns.
3. Tighten the 3 cap screws (213) evenly by
alternating the cap screws until the shaft can no
longer be turned by hand at the coupling. This
will lower the rotating assembly, seating the
impeller (2) against the suction cover or casing.
Motor bearings should be lubricated in accord with motor
manufacturer’s recommendations.
4. Loosen the cap screws (213) ½ turn. Carefully
tighten the 3 jackscrews (286) by alternating the
jackscrews approximately 1 - 1½ hex to obtain the
desired .015 inches clearance. Retighten the cap
screws (213) until snug and then tighten the
adjusting lock nuts (204) to lock adjustment. Make
sure that the shaft turns freely by hand before
starting the pump.
Care should be exercised in keeping all parts of the pump
clean when out of the pump. Special precautions must
be taken to keep ball bearings and lip seals dirt-free at all
times.
5. Reassemble coupling and place pump in
operation.
When ordering repairs, refer to the illustration for correct
item names and to the pump nameplate on which is
stamped the pump model number, size and serial number
which must be available when ordering repairs.
J - GENERAL MAINTENANCE &
REPAIRS
Any part which is excessively worn or deteriorated and
all gaskets should be replaced with new parts before
reassembling the pump.
H - DISCHARGE PIPE
Improper alignment of the discharge pipe (161) may cause
the shaft to bind. Loosen the top pipe lock nut (294) 2 to
3 turns and test for shaft rotation. If shaft is free, gradually
tighten the top pipe lock nut checking shaft rotation as the
nut is tightened.
K - FOR INSPECTION OR REPAIR
OF LIQUID END
If the shaft still binds, lift the pump from the tank or pit
and loosen the bottom pipe lock nut. Continue to tighten
the top pipe lock nut and the binding should be relieved.
Tighten the bottom pipe lock nut when maximum shaft
freedom has been accomplished and make sure that the
top pipe lock nut is tight.
An accurate check of the impeller and pump alignment can
be established by the use of a watt meter to measure the
minimum power requirement of the motor.
5
1.
Close the gate valve in the discharge line and LOCK
THE ENTRANCE DISCONNECT SWITCH IN THE
OFF POSITION.
2.
Remove power leads from the motor. Disconnect the
discharge pipe at the pump base plate.
3.
Disengage the flexible shaft coupling, per manufacturer’s
instructions. Remove motor cap screws (219) then
remove motor from the motor pedestal (81). Remove
foundation bolts in the base plate (23), and lift pump and
base plate from pit to the floor or other suitable support.
4.
5.
a.
If the pump is furnished with threaded discharge
fittings, unscrew the pipe coupling or flange
(295) from the top end of the discharge pipe
then remove the top pipe nut (294) and unscrew
the lower pipe nut to the end of the threads.
Unscrew the discharge pipe (161) from the
discharge elbow (105).
b.
If the pump is furnished with combination elbow
(105), remove the cap screws and nuts (267)
and (268) at the pump discharge flange.
e.
L - TO INSPECT BALL BEARINGS &
SEALS OR SHAFT
Liquid end disassembly
a. Remove cap screws (215), then place a block
of wood against the finished flange or back
of the suction cover (9) and tap the block lightly
with a hammer to loosen the suction cover.
Remove the suction cover and the gasket (73).
b.
c.
Bend and remove the cotter pin (269) and the
castellated impeller nut (24). Hold shaft with a
wrench at the coupling (42) and unscrew the
impeller nut (24) by turning counter clockwise,
also remove the impeller washer (270).
To remove impeller (2) from the shaft (6) it will
be necessary to make 3 special jackscrews
depending upon the size of the liquid end as
follows:
1.) If the discharge outlet of the casing (1)
is threaded 1”, 1½” or 2½” and the
impeller diameter is 6” or less, the
required jackscrews are 3/8” x 16NC,
1¾” long.
1.
Remove Liquid end assembly.
2.
Remove coupling (42) and key (46) from shaft (6).
3.
Remove cap screws (221) and nuts (261) and lift
driver pedestal (81) from frame (19).
4.
Remove cap screw (213). Unscrew the 3 lock nuts
(204) until against the head of the jackscrew (286)
then remove jackscrews. Slide bearing cover (37)
with seal (49) off the top end of the shaft (6). Inspect
the seal and replace if worn.
5.
Bend tape on bearing lock washer (69) then unscrew
and remove the bearing lock nut (22) and bearing
lock washer (69).
6.
Replace the jackscrews (286) in the bearing housing
flange and toghten the jackscrews to raise the
bearing housing (33) and ball bearing (18) from the
top of the frame (19). A pry bar may be required to
assist in removing the bearing housing. Carefully
press the ball bearing from the bearing housing.
7.
Carefully withdraw the pump shaft and ball bearing
(16) upward through the frame (19). Remove the
bearing (16) from the shaft.
8.
Inspect the bearing cover seal (47) and if worn
replace with new seal. Bearing cover (35) and seal
may be removed from the frame using a piece of
pipe or tubing inserted through the top of the frame
to force the bearing cover from the frame.
M - TO REASSEMBLE BALL
BEARINGS AND SEALS
2.) For all other sizes of liquid ends the
required jackscrews are 1/2” x 13NC, 3”
long.
Thread the jackscrews into the 3 tapped holes
in the impeller shroud and tighten alternating
jackscrews, until the impeller is forced from
the shaft. Lift impeller key (32) from its seat.
d.
Inspect the throttle bushing (252) for excessive
wear and replace by unscrewing the cap screw
(218) and pressing the bushing from the
housing. Press new bushing into the throttle
housing (99), aligning the slot with the cap screw
(218) then tighten cap screw until firm. Slide
deflector (40) from the shaft.
The casing (1) and throttle housing (99) may be
removed from the column pipe (101) after
removing cap screws (212).
6
1.
Slide bearing (16) onto the shaft. Position the
bearing so that the inner bearing race is against the
shaft shoulder. CAUTION: Apply force only to the
inner bearing race.
2.
If the bearing cover (35) and the seal (47) were
removed from the frame, apply sufficient grease to
fill the space below the ball bearing (16). Press
bearing cover with seal into the frame from the
impeller end until the bearing cover is flushed with
the frame. Be sure that seal (47) is installed with the
spring side of the seal toward the impeller.
3.
4.
5.
6.
7.
O - CHAIR BRACKET MOUNTING
Insert shaft with bearing, impeller end first, into the
top of the frame (19) being careful not to damage the
seal (47).
(See page 8)
The foot mounted horizontal type motor and flexible shaft
coupling are shipped unmounted and must be mounted
on the pump prior to installation of the pump.
Place bearing housing (33) in a vice with the flange
resting on vice jaws. Apply light oil to interior of
housing then press bearing (18) into the bearing
housing making sure that the bearing is fully seated
in the bearing housing. CAUTION: Apply force to
the outer ring of the bearing only. Place the
assembly over the end of the pump shaft and press
into position so that the inner race of the bearing is
against the shaft shoulder. CAUTION: Apply force to
the inner ring of the bearing only.
Mount the pump half coupling on the pump shaft (6) and
the motor half coupling on the motor shaft according to
manufacturer’s recommendations.
Place the pump in a horizontal position on a bench or
suitable support. Place motor, shaft toward the pump, on
the chair bracket with motor feet positioned on the motor
mounting screws (2).
Place lock washer (69) over the bearing and thread
the bearing lock nut (22) onto the shaft and tighten
securely. Bend tabs of lock washer into slots in the
bearing lock nut.
Insert motor anchor cap screws (5) thru holes in motor
feet and into the motor mounting screws. Tighten
sufficiently to hold motor in position.
If frame (19) was removed from the support plate
(23), mount the frame on the base plate replacing cap
screw and nuts (221) and (258)
Adjust motor mounting screws until motor shaft and
coupling is aligned with the pump shaft, both angular and
paralleled alignment.
Slide deflector (40) onto the shaft.
Angular alignment check is made by inserting taper
gauge or feelers between coupling faces at 90° intervals
around the coupling. The coupling faces should be the
same distance apart. Adjust motor mounting screws to
achieve alignment.
N - ASSEMBLY OF LIQUID END
1.
Place throttle housing (99) with throttle bushing over
impeller end of shaft. Align bolt holes and position
against column pipe (101).
2.
Position gasket (241) on throttle housing (99) then
place casing (1) against the flange of the throttle
housing aligning the holes and with the discharge
outlet in the proper position. Replace cap screws (212).
3.
Insert impeller key (32) into shaft keyway and place
impeller (2) on shaft with keyway over impeller key.
Place wooden block over impeller vanes and tap
lightly on the wood block to seat the impeller on the
shaft. Back up coupling end of shaft to prevent
bearing damage.
4.
5.
Paralleled alignment check is made by placing a straight
edge across both coupling rims at 90° intervals around
the coupling. Straight edge should rest evenly on coupling
halves at each point. Correction can be made by adjusting
motor mounting screws. When properly aligned, tighten
motor anchor cap screws (5) and lock nuts (3).
Place the assemble pump in a vertical position on the
tank or pit and connect discharge pipe to pump discharge.
NOTE: Pipe and fittings must be properly supported
so their weight does not rest on pump. Rechech
angular and paralleled alignment and correct as
necessary. Turn pump shaft by hand several times to be
sure that it rotates freely.
Replace impeller washer (270) onto the shaft then the
castellated nut (24). Tighten the nut and place new
cotter pin (269) through nut and shaft. CAUTION:
Do Not use impeller nut to draw the impeller
onto the shaft. The nut is a locking device only.
Recommended torque for tightening the impeller nut
is as follows:
1/2” - 45 Ft. lbs.
5/8” - 90 Ft. lbs.
3/4” - 170 Ft. lbs.
Connect power leads to motor according to motor wiring
diagram, jog starter, testing for proper pump rotation;
normally clockwise (righ hand) when looking down on top
of motor.
Place pump in operation. If there is vibration in the unit,
rechech alignment at the shaft coupling and refer to
“Pump Adjustment”.
Place gasket (73) on suction cover (9). Position cover
against the casing (1) and replace and tighten cap
screws (215).
7
Chair Bracket Mounting
P - LOCATING TROUBLE
1
Motor Support
2
Motor Mounting Screw
3
Lock Nut
4
Motor Foot
5
Motor Anchor Cap Screw
3. Not enough pressure
a. Air in water
b. Mechanical defects
c. Impeller diameter too small
d. Wrong direction of rotation
e. Impeller not properly adjusted
f. Discharge head (line friction) lower than expected
1. No water delivered
a. Wrong direction of rotation
b. Impeller or pipes plugged
c. Discharge head too high
d. No water in pit
e. Pump suction to close to bottom of pit
4. Pump takes too much power
a. Speed too high for required head and capacity
b. Head lower than rating; pumps to much water
c. Liquid either viscous or heaver than water or both
d. Mechanical defects
1. Shaft bent
2. Impeller binds in casing
e. Strain on pump caused by piping misalignment
f. Impeller not adjusted properly
2. Not enough water delivered
a. Discharge head higher than expected
b. Impeller or pipes partly plugged
c. Improper impeller adjustment
d. Low water level in pit
e. Mechanical defects
1. Impeller worn or damaged
2. Casing worn
f. Wrong direction of rotation
8
ITEM No.
001
002
006
009
*016
*018
019
022
023
*024
032
033
035
037
040
042
046
*047
*049
069
*073
081
099
101
105
161
204
212
213
215
218
219
221
228
*241
242
252
258
260
261
265
267
268
*269
270
286
294
295
332
335
*336
(*) Recommended Spare Parts
9
DESCRIPTION
Casing
Impeller
Shaft
Suction Cover
Ball Bearing (Inboard)
Ball Bearing (Outboard)
Frame
Lock Nut (Bearing)
Base Plate
Impeller Nut
Impeller Key
Bearing Housing (Outboard)
Bearing Cover (Inboard)
Bearing Cover (Outboard)
Deflector
Coupling
Coupling Key
Bearing Cover Seal
Bearing Cover Seal
Bearing Lock Washer
Gasket
Drive Pedestal
Throttle Housing
Column
Discharge Elbow
Discharge Pipe
Adjusting Lock Nut
Cap Screw
Cap Screw
Cap Screw
Cap Screw
Cap Screw
Cap Screw
Motor
Gasket
Grease Fitting
Throttle Bushing
Hex Nut
Cap Screw
Hex Nut
Cap Screw
Cap Screw
Cap Screw
Cotter Pin
Impeller Washer
Jackscrew
Pipe Nut
Discharge Flange
Cap Screw (Not Shown)
Lube Pipe Assembly
Gasket
Limited 24 Month Warranty
Crane Pumps & Systems warrants that products of our manufacture will be free of defects in material and workmanship
under normal use and service for twenty-four (24) months after manufacture date, when installed and maintained
in accordance with our instructions.This warranty gives you specific legal rights, and there may also be other rights
which vary from state to state. In the event the product is covered by the Federal Consumer Product Warranties Law
(1) the duration of any implied warranties associated with the product by virtue of said law is limited to the same
duration as stated herein, (2) this warranty is a LIMITED WARRANTY, and (3) no claims of any nature whatsoever
shall be made against us, until the ultimate consumer, his successor, or assigns, notifies us in writing of the defect,
and delivers the product and/or defective part(s) freight prepaid to our factory or nearest authorized service station.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply.
THE SOLE AND EXCLUSIVE REMEDY FOR BREACH OF ANY AND ALL WARRANTIES WITH RESPECT TO ANY
PRODUCT SHALL BE TO REPLACE OR REPAIR AT OUR ELECTION, F.O.B. POINT OF MANUFACTURE OR
AUTHORIZED REPAIR STATION, SUCH PRODUCTS AND/OR PARTS AS PROVEN DEFECTIVE. THERE SHALL BE
NO FURTHER LIABILITY, WHETHER BASED ON WARRANTY, NEGLIGENCE OR OTHERWISE. Unless expressly
stated otherwise, guarantees in the nature of performance specifications furnished in addition to the foregoing material
and workmanship warranties on a product manufactured by us, if any, are subject to laboratory tests corrected for
field performance. Any additional guarantees, in the nature of performance specifications must be in writing and such
writing must be signed by our authorized representative. Due to inaccuracies in field testing if a conflict arises between
the results of field testing conducted by or for user, and laboratory tests corrected for field performance, the latter
shall control. RECOMMENDATIONS FOR SPECIAL APPLICATIONS OR THOSE RESULTING FROM SYSTEMS
ANALYSES AND EVALUATIONS WE CONDUCT WILL BE BASED ON OUR BEST AVAILABLE EXPERIENCE AND
PUBLISHED INDUSTRY INFORMATION. SUCH RECOMMENDATIONS DO NOT CONSTITUTE A WARRANTY OF
SATISFACTORY PERFORMANCE AND NO SUCH WARRANTY IS GIVEN.
This warranty shall not apply when damage is caused by (a) improper installation, (b) improper voltage (c) lightning
(d) excessive sand or other abrasive material (e) scale or corrosion build-up due to excessive chemical content. Any
modification of the original equipment will also void the warranty. We will not be responsible for loss, damage or labor
cost due to interruption of service caused by defective parts. Neither will we accept charges incurred by others without
our prior written approval.
This warranty is void if our inspection reveals the product was used in a manner inconsistent with normal industry practice
and\or our specific recommendations. The purchaser is responsible for communication of all necessary information
regarding the application and use of the product. UNDER NO CIRCUMSTANCES WILL WE BE RESPONSIBLE FOR
ANY OTHER DIRECT OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO TRAVEL EXPENSES,
RENTED EQUIPMENT, OUTSIDE CONTRACTOR FEES, UNAUTHORIZED REPAIR SHOP EXPENSES, LOST
PROFITS, LOST INCOME, LABOR CHARGES, DELAYS IN PRODUCTION, IDLE PRODUCTION, WHICH DAMAGES
ARE CAUSED BY ANY DEFECTS IN MATERIAL AND\OR WORKMANSHIP AND\OR DAMAGE OR DELAYS IN
SHIPMENT. THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER EXPRESS OR IMPLIED WARRANTY,
INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
No rights extended under this warranty shall be assigned to any other person, whether by operation of law or otherwise,
without our prior written approval.
A Crane Co. Company
420 Third Street
Piqua, Ohio 45356
Phone: (937) 778-8947
Fax: (937) 773-7157
www.cranepumps.com
83 West Drive, Brampton
Ontario, Canada L6T 2J6
Phone: (905) 457-6223
Fax: (905) 457-2650
IMPORTANT!
WARRANTY REGISTRATION
Your product is covered by the enclosed Warranty.
To complete the Warranty Registration Form go to:
http://www.cranepumps.com/ProductRegistration/
If you have a claim under the provision of the warranty, contact your local
Crane Pumps & Systems, Inc. Distributor.
RETURNED GOODS
RETURN OF MERCHANDISE REQUIRES A “RETURNED GOODS AUTHORIZATION”.
CONTACT YOUR LOCAL CRANE PUMPS & SYSTEMS, INC. DISTRIBUTOR.
Products Returned Must Be Cleaned, Sanitized,
Or Decontaminated As Necessary Prior To Shipment,
To Insure That Employees Will Not Be Exposed To Health
Hazards In Handling Said Material. All Applicable Laws
And Regulations Shall Apply.
Notes

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project