Edirol UA-1000 Owner`s manual

Edirol UA-1000 Owner`s manual
UA-1000_e.book 1 ページ 2003年8月6日 水曜日 午前11時52分
Owner’s Manual
Before using this unit, carefully read the sections entitled: “IMPORTANT
SAFETY INSTRUCTIONS” (p. 2), “USING THE UNIT SAFELY” (pp. 3–4), and
“IMPORTANT NOTES” (pp. 5–6). These sections provide important information
concerning the proper operation of the unit. Additionally, in order to feel
assured that you have gained a good grasp of every feature provided by your
new unit, Owner’s Manual should be read in its entirety. The manual should be
saved and kept on hand as a convenient reference.
Copyright © 2003 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the
written permission of ROLAND CORPORATION.
UA-1000_e.book 2 ページ 2003年8月6日 水曜日 午前11時52分
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING - When using electric products, basic precautions should always be followed, including the following:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any of the ventilation openings. Install in
accordance with the manufacturers instructions.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. When the provided
plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Never use with a cart, stand, tripod, bracket,
or table except as specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
For the U.K.
WARNING:
THIS APPARATUS MUST BE EARTHED
IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
GREEN-AND-YELLOW: EARTH, BLUE: NEUTRAL, BROWN: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the
letter E or by the safety earth symbol or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
2
UA-1000_e.book 3 ページ 2003年8月6日 水曜日 午前11時52分
USING THE UNIT SAFELY
The
symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
general cautions, warnings, or alerts to danger.
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers
other adverse effects
respect to the home
furnishings, as well
animals or pets.
The
symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
to damage or
caused with
and all its
to domestic
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.
008a
001
• Before using this unit, make sure to read the
instructions below, and the Owner’s Manual.
..........................................................................................................
002a
• Do not open or perform any internal modifications on the unit.
• The unit should be connected to a power supply
only of the type described in the operating instructions, or as marked on the side of unit.
..........................................................................................................
008e
• Use only the attached power-supply cord.
..........................................................................................................
..........................................................................................................
003
009
• Do not attempt to repair the unit, or replace parts
within it (except when this manual provides
specific instructions directing you to do so). Refer
all servicing to your retailer, the nearest Roland
Service Center, or an authorized Roland
distributor, as listed on the “Information” page.
..........................................................................................................
004
• Never use or store the unit in places that are:
• Subject to temperature extremes (e.g., direct
sunlight in an enclosed vehicle, near a heating
duct, on top of heat-generating equipment); or
are
• Damp (e.g., baths, washrooms, on wet floors);
or are
• Humid; or are
• Exposed to rain; or are
• Dusty; or are
• Subject to high levels of vibration.
..........................................................................................................
• Do not excessively twist or bend the power cord,
nor place heavy objects on it. Doing so can
damage the cord, producing severed elements and
short circuits. Damaged cords are fire and shock
hazards!
..........................................................................................................
010
• This unit, either alone or in combination with an
amplifier and headphones or speakers, may be
capable of producing sound levels that could
cause permanent hearing loss. Do not operate for
a long period of time at a high volume level, or at
a level that is uncomfortable. If you experience
any hearing loss or ringing in the ears, you should
immediately stop using the unit, and consult an
audiologist.
..........................................................................................................
011
• Do not allow any objects (e.g., flammable material,
coins, pins); or liquids of any kind (water, soft
drinks, etc.) to penetrate the unit.
005
• This unit should be used only with a rack or stand
that is recommended by Roland.
..........................................................................................................
..........................................................................................................
006
• When using the unit with a rack or stand recommended by Roland, the rack or stand must be
carefully placed so it is level and sure to remain
stable. If not using a rack or stand, you still need
to make sure that any location you choose for
placing the unit provides a level surface that will
properly support the unit, and keep it from
wobbling.
..........................................................................................................
3
UA-1000_e.book 4 ページ 2003年8月6日 水曜日 午前11時52分
012a:
• Immediately turn the power off, remove the
power cord from the outlet, and request servicing
by your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, as
listed on the “Information” page when:
• The power-supply cord, or the plug has been
damaged; or
• If smoke or unusual odor occurs
• Objects have fallen into, or liquid has been
spilled onto the unit; or
• The unit has been exposed to rain (or otherwise
has become wet); or
• The unit does not appear to operate normally or
exhibits a marked change in performance.
..........................................................................................................
013
• In households with small children, an adult
should provide supervision until the child is
capable of following all the rules essential for the
safe operation of the unit.
..........................................................................................................
014
• Protect the unit from strong impact.
(Do not drop it!)
..........................................................................................................
015
• Do not force the unit’s power-supply cord to share
an outlet with an unreasonable number of other
devices. Be especially careful when using
extension cords—the total power used by all
devices you have connected to the extension
cord’s outlet must never exceed the power rating
(watts/amperes) for the extension cord. Excessive
loads can cause the insulation on the cord to heat
up and eventually melt through.
..........................................................................................................
016
• Before using the unit in a foreign country, consult
with your retailer, the nearest EDIROL/Roland
Service Center, or an authorized EDIROL/Roland
distributor, as listed on the “Information” page.
..........................................................................................................
023
• DO NOT play a CD-ROM disc on a conventional
audio CD player. The resulting sound may be of a
level that could cause permanent hearing loss.
Damage to speakers or other system components
may result.
..........................................................................................................
026
• Do not put anything that contains water (e.g.,
flower vases) on this unit. Also, avoid the use of
insecticides, perfumes, alcohol, nail polish, spray
cans, etc., near the unit. Swiftly wipe away any
liquid that spills on the unit using a dry, soft cloth.
..........................................................................................................
101a
• The unit should be located so that its location or
position does not interfere with its proper ventilation.
..........................................................................................................
102b
• Always grasp only the plug on the power-supply
cord when plugging into, or unplugging from, an
outlet or this unit.
..........................................................................................................
103a:
• At regular intervals, you should unplug the power
plug and clean it by using a dry cloth to wipe all
dust and other accumulations away from its
prongs. Also, disconnect the power plug from the
power outlet whenever the unit is to remain
unused for an extended period of time. Any
accumulation of dust between the power plug and
the power outlet can result in poor insulation and
lead to fire.
..........................................................................................................
104
• Try to prevent cords and cables from becoming
entangled. Also, all cords and cables should be
placed so they are out of the reach of children.
..........................................................................................................
106
• Never climb on top of, nor place heavy objects on
the unit.
..........................................................................................................
107b
• Never handle the power cord or its plugs with wet
hands when plugging into, or unplugging from,
an outlet or this unit.
..........................................................................................................
108a
• Before moving the unit, disconnect the power
plug from the outlet, and pull out all cords from
external devices.
..........................................................................................................
109a
• Before cleaning the unit, turn off the power and
unplug the power cord from the outlet (p. **).
..........................................................................................................
110a
• Whenever you suspect the possibility of lightning
in your area, pull the plug on the power cord out
of the outlet.
..........................................................................................................
118
• Whenever you've removed any screws—whether
it be when installing a rackmount adaptor—be
sure to place the screws out of reach of small
children, so they won't be swallowed accidentally.
..........................................................................................................
120
• Always turn the phantom power off when
connecting any device other than condenser
microphones that require phantom power. You
risk causing damage if you mistakenly supply
phantom power to dynamic microphones, audio
playback devices, or other devices that don't
require such power. Be sure to check the specifications of any microphone you intend to use by
referring to the manual that came with it.
(This instrument's phantom power: 48 V DC, 10 mA Max x 2
systems)
..........................................................................................................
4
UA-1000_e.book 5 ページ 2003年8月6日 水曜日 午前11時52分
IMPORTANT NOTES
291b
In addition to the items listed under “IMPORTANT SAFETY INSTRUCTIONS” and “USING THE UNIT SAFELY” on pages 2
and 4, please read and observe the following:
Power Supply
Repairs and Data
301
452
• Do not use this unit on the same power circuit with any
device that will generate line noise (such as an electric
motor or variable lighting system).
• Please be aware that all data contained in the unit's
memory may be lost when the unit is sent for repairs.
Important data should always be written down on paper.
During repairs, due care is taken to avoid the loss of data.
However, in certain cases (such as when circuitry related
to memory itself is out of order), we regret that it may not
be possible to restore the data, and Roland assumes no
liability concerning such loss of data.
307
• Before connecting this unit to other devices, turn off the
power to all units. This will help prevent malfunctions
and/or damage to speakers or other devices.
308
• Although the LCD and LEDs are switched off when the
POWER switch is switched off, this does not mean that the
unit has been completely disconnected from the source of
power. If you need to turn off the power completely, first
turn off the POWER switch, then unplug the power cord
from the power outlet. For this reason, the outlet into
which you choose to connect the power cord’s plug
should be one that is within easy reach.
Placement
351
• Using the unit near power amplifiers (or other equipment
containing large power transformers) may induce hum.
To alleviate the problem, change the orientation of this
unit; or move it farther away from the source of interference.
352a
• This device may interfere with radio and television
reception. Do not use this device in the vicinity of such
receivers.
352b
• Noise may be produced if wireless communications
devices, such as cell phones, are operated in the vicinity of
this unit. Such noise could occur when receiving or initiating a call, or while conversing. Should you experience
such problems, you should relocate such wireless devices
so they are at a greater distance from this unit, or switch
them off.
355b
• When moved from one location to another where the
temperature and/or humidity is very different, water
droplets (condensation) may form inside the unit. Damage
or malfunction may result if you attempt to use the unit in
this condition. Therefore, before using the unit, you must
allow it to stand for several hours, until the condensation
has completely evaporated.
Maintenance
401a
• For everyday cleaning wipe the unit with a soft, dry cloth
or one that has been slightly dampened with water. To
remove stubborn dirt, use a cloth impregnated with a
mild, non-abrasive detergent. Afterwards, be sure to wipe
the unit thoroughly with a soft, dry cloth.
Additional Precautions
551
• Please be aware that the contents of memory can be
irretrievably lost as a result of a malfunction, or the
improper operation of the unit. To protect yourself against
the risk of losing important data, we recommend that you
periodically write down important data you have stored
in the unit's memory on paper.
552
• Unfortunately, it may be impossible to restore the contents
of data that was stored in the unit’s memory once it has
been lost. Roland Corporation assumes no liability
concerning such loss of data.
553
• Use a reasonable amount of care when using the unit’s
buttons, sliders, or other controls; and when using its jacks
and connectors. Rough handling can lead to malfunctions.
556
• When connecting / disconnecting all cables, grasp the
connector itself—never pull on the cable. This way you
will avoid causing shorts, or damage to the cable’s
internal elements.
557
• A small amount of heat will radiate from the unit during
normal operation.
558a
• To avoid disturbing your neighbors, try to keep the unit’s
volume at reasonable levels. You may prefer to use
headphones, so you do not need to be concerned about
those around you (especially when it is late at night).
559a
• When you need to transport the unit, package it in the box
(including padding) that it came in, if possible. Otherwise,
you will need to use equivalent packaging materials.
562
• Use a cable from Roland to make the connection. If using
some other make of connection cable, please note the
following precautions.
• Some connection cables contain resistors. Do not use
cables that incorporate resistors for connecting to this
unit. The use of such cables can cause the sound level
to be extremely low, or impossible to hear. For information on cable specifications, contact the manufacturer of the cable.
402
• Never use benzine, thinners, alcohol or solvents of any
kind, to avoid the possibility of discoloration and/or
deformation.
5
UA-1000_e.book 6 ページ 2003年8月6日 水曜日 午前11時52分
Handling CD-ROMs
801
• Avoid touching or scratching the shiny underside
(encoded surface) of the disc. Damaged or dirty CD-ROM
discs may not be read properly. Keep your discs clean
using a commercially available CD cleaner.
Copyright
851
• Unauthorized recording, distribution, sale, lending, public
performance, broadcasting, or the like, in whole or in part,
of a work (musical composition, video, broadcast, public
performance, or the like) whose copyright is held by a
third party is prohibited by law.
852a
• When exchanging audio signals through a digital
connection with an external instrument, this unit can
perform recording without being subject to the restrictions
of the Serial Copy Management System (SCMS). This is
because the unit is intended solely for musical production,
and is designed not to be subject to restrictions as long as
it is used to record works (such as your own compositions) that do not infringe on the copyrights of others.
(SCMS is a feature that prohibits second-generation and
later copying through a digital connection. It is built into
MD recorders and other consumer digital-audio
equipment as a copyright-protection feature.)
853
• Do not use this unit for purposes that could infringe on a
copyright held by a third party. We assume no responsibility whatsoever with regard to any infringements of
third-party copyrights arising through your use of this
unit.
204
* Microsoft and Windows are registered trademarks of Microsoft Corporation.
206e
* The screen shots in this document are used in compliance with the guidelines of the Microsoft Corporation.
206j
* Windows® is known officially as: “Microsoft® Windows® operating system.”
220
* All product names mentioned in this document are trademarks or registered trademarks of their respective owners.
6
UA-1000_e.book 7 ページ 2003年8月6日 水曜日 午前11時52分
Contents
USING THE UNIT SAFELY......................................................................3
IMPORTANT NOTES ...............................................................................5
Main features...........................................................................................8
Contents of the package ........................................................................9
Panel Descriptions................................................................................11
Front panel................................................................................................................................................. 11
Rear panel .................................................................................................................................................. 15
Preparations for using the UA-1000....................................................18
Installing the driver.................................................................................................................................. 18
Giving priority to background services ................................................................................................ 22
Driver settings........................................................................................................................................... 23
Basic connections and settings ..........................................................26
Basic connections...................................................................................................................................... 26
Recording a mic or guitar........................................................................................................................ 27
Recording onto an external ADAT device............................................................................................ 29
Capturing sound from an external ADAT device ............................................................................... 30
Monitoring 5.1 channel sound................................................................................................................ 31
Inserting an external effects processor .................................................................................................. 32
Recording a digital input signal ............................................................................................................. 33
Synchronizing to the word clock input ................................................................................................. 34
Various settings ....................................................................................36
Internal blocks of the UA-1000 ............................................................................................................... 36
UA-1000 Control Panel ............................................................................................................................ 36
Adjusting the audio latency.................................................................................................................... 40
Using ASIO Direct Monitor .................................................................................................................... 40
Synchronization settings .....................................................................41
About the ADAT mode switch and external clock switch ................................................................. 41
System settings ....................................................................................44
Restoring the factory settings (Factory Reset)...................................................................................... 44
Troubleshooting....................................................................................45
Problems related to the USB driver ....................................................................................................... 45
Deleting the driver ................................................................................................................................... 45
Problems related to the UA-1000 ........................................................................................................... 46
Main specifications...............................................................................50
Block diagram .......................................................................................51
INDEX .....................................................................................................53
7
UA-1000_e.book 8 ページ 2003年8月6日 水曜日 午前11時52分
Main features
480 Mbps transfer speed with hi-speed USB (USB 2.0), supporting
10 IN/10 OUT at superb 24-bit/96 kHz audio quality
Ten independent channels of simultaneous recording and playback are supported with superb 24-bit/96 kHz
audio quality.
If your computer has a USB 2.0 connector, you can implement a cutting-edge recording environment by
connecting a single USB cable.
Four channels of high-performance mic preamp
High-performance mic preamp equivalent to those used on the Roland VS-2480 deliver transparent sound.
The UA-1000 uses the same carefully selected analog parts as on the Roland VS-2480, giving you great audio
quality and plenty of recording headroom.
A rich array of inputs and outputs in a single rack space
Four TRS/XLR combo jacks with phantom power, a high-impedance (Hi-Z) jack for direct connection of a
guitar or bass, and optical/coaxial digital input/output connectors are provided.
The optical jacks can also be used as an eight-channel ADAT interface (*).
In addition, the UA-1000 provides four input/output jacks for effect insertion, MIDI input/output, and word
clock input/output jacks for precise recording synchronization with external digital devices.
* When the UA-1000 is not connected to a computer, it can function as a multi-channel analog <-> digital
converter or an ADAT <-> analog converter.
* The UA-1000’s analog inputs cannot be used while in ADAT recording mode.
Built-in digital mixer
The internal digital mixer can be controlled directly from the UA-1000 Control Panel on your computer.
The Direct Monitor function allows realtime monitoring of the ten channels of input without passing them
through your computer software.
WDM and ASIO 2.0 compatible
WDM and ASIO 2.0 compatible low-latency driver is provided.
The driver delivers superb performance with any DAW application, such as SONAR and Cubase.
MIDI interface with FPT ensures high speed and low jitter
FPT (Fast Processing Technology of MIDI Transmission) ensures stable, high-speed transmission and
reception with consistent latency and minimal jitter, regardless of the density of MIDI data.
8
UA-1000_e.book 9 ページ 2003年8月6日 水曜日 午前11時52分
Contents of the package
■ UA-1000
fig.ua1000
■ Power cord
This is the only power cord you should use with the UA-1000. Do not use any power cord other than the
supplied one, since doing so may cause malfunction.
■ USB cable
Use this to connect the USB connector of your computer with the USB connector of the UA-1000.
* Please use only the included USB cable. If you require a replacement due to loss or damage, please contact a “EDIROL/
Roland Service Center” listed in the “Information” section at the end of this manual.
■ Owner’s Manual
This is the manual you are reading. Please keep it on hand for reference.
■ CD-ROM
This contains the driver required in order to use the UA-1000.
* You must read the license agreement before opening the CD-ROM. Opening the CD-ROM case will be considered
acceptance of the license agreement.
* Do not touch the recorded (unprinted) surface of the disc or allow it to be scratched. Doing so may render the disc
unreadable. If the disc gets dirty, use a commercially available CD cleaner to clean it.
Do not play back the CD-ROM in a conventional audio CD player. Doing so may produce high-volume sound
that can damage your hearing and/or speakers.
9
UA-1000_e.book 10 ページ 2003年8月6日 水曜日 午前11時52分
Contents of the package
■ Rackmount adaptors (two pcs.)
Use this when you want to install the UA-1000 in an audio rack. Two rack ears are included.
Attaching the rackmount adaptors
If you want to install the UA-1000 in a rack, attach the rackmount adaptors as shown in the diagram.
fig.angle
1. Remove three screws (on each side)
from the right and left panels of the
UA-1000.
2. Using the screws you removed in
step 1, attach the rackmount
brackets to the UA-1000.
* You must use the screws that you
removed. Do not use any other screws.
■ Ferrite Core (for 230V and 240V)
The ferrite core should be attached to the cord of your headphones.
Attaching the Ferrite Core
Before using headphones, make sure to attach the ferrite core.
If you will be using headphones, please follow the instructions below to clamp the supplied ferrite core over
the cord. Afterwards, make sure to leave it on the cord, since it serves in blocking electromagnetic noise.
fig.ferraite-1
1. Open the ferrite core and position it over the cord.
* Make sure to position it so it’s close to the plug.
fig.ferraite-2
2. Wrap the cord around the ferrite core; one turn is enough.
fig.ferraite-3
3. Close it firmly; you should hear a distinct sound as it clicks shut.
* Take care not to get your fingers pinched when attaching the ferrite core.
* Make sure you don’t apply undue force and damage the cord when clamping on
the ferrite core.
10
UA-1000_e.book 11 ページ 2003年8月6日 水曜日 午前11時52分
Panel Descriptions
Front panel
fig.front
fig.panel-input
1. Combo input jacks 1–4
6
1
4
3
These are analog audio input jacks with high-quality
preamps. Either XLR type or phone type jacks can be
connected here, as appropriate for the equipment you are
using. Balanced or unbalanced connections are supported.
The XLR type jacks provide 48 V phantom power, allowing
you to connect phantom-powered condenser mics. In this
case, turn on the phantom power switch.
2
5
fig.XLR-TRS
* This instrument is equipped with balanced (XLR/TRS) type input
jacks. Wiring diagrams for these jacks are shown on the right.
Make connections after first checking the wiring diagrams of other
equipment you intend to connect.
GND(SLEEVE)
1:GND
2:HOT
3:COLD
HOT(TIP)
COLD(RING)
2. Input sensitivity knobs
These adjust the input level of the signals that are input to front panel combo input jacks 1–4 and rear panel input
jacks 5–8.
fig.sens
2
3. Phantom power switches 1, 2 (PHANTOM 48 V)
These are on/off switches for the phantom power that is supplied to the XLR type connectors of combo input jacks
1–2 and 3–4. Phantom power is on when the switch is pressed inward ( ), and off when the switch is in the outward
position ( ).
fig.jack-type
* You must turn phantom power off (button in the outward position) unless a condenser
microphone requiring a phantom power supply is connected to the XLR type jacks.
Malfunctions will occur if you supply phantom power to a dynamic microphone or to an
audio playback device. For details on the specifications of your microphone, refer to the
owner’s manual for your microphone.
XLR plug
(The UA-1000 supplies phantom power at DC 48 V, maximum 10 mA x 2 systems)
4. Gain select switches (PAD)
These switch the input level. Turn these on (button in the
output gain.
TRS phone
Phone plug
plug
(unbalanced) (balanced)
inward position) if you connect devices that have a high
11
UA-1000_e.book 12 ページ 2003年8月6日 水曜日 午前11時52分
Panel Descriptions
5. Input peak indicators
These indicate whether distortion is occurring in the sound being input to each input jack. The peak indicators will
light red at a level before the sound begins to distort (-6 dB). Adjust the corresponding input sensitivity knob or the
output level of your equipment so that the peak indicators do not light red.
6. Input impedance select switch
For the phone jack input of combo input jack 3, you can select either high impedance (Hi-Z (button in the
inward
position)) or low impedance (Lo-Z (button in the outward position)), as appropriate for the device that is
connected. Select high impedance (Hi-Z) if you have connected a guitar or bass.
fig.direct-monitor
7
8 9 11
12 14
10 13
18 19
15 16 17
7. Output indicators
If audio data is being output from the UA-1000, the output indicator for the jack from which audio data is being
output will light. For example, if audio data is being output from output jack 1, output indicator “1” will light green.
Indicators “9” and “10” will light to indicate output from the digital output connector.
This provides a convenient way to check the settings of the UA-1000’s internal patch bay. For details, refer to
“Internal blocks of the UA-1000” (p. 36).
8. ADAT mode switch
When you press the ADAT mode switch, the ADAT mode switch will light and the UA-1000 will be in ADAT Output
mode; ADAT format signals will be output from the optical digital output jack.
If you simultaneously press the ADAT mode switch and the external clock switch, the PEAK/SIG/ADAT IN
indicators will all light orange, and the UA-1000 will be in ADAT Input/Output mode; ADAT format signals will be
input from the optical input jack.
* If you are using ADAT mode, you must set the UA-1000 to 44.1 kHz or 48 kHz. If a setting other than 44.1 kHz or 48 kHz is
selected, ADAT mode will not be available; pressing the ADAT mode switch will not cause the ADAT mode switch to light.
Turning off the power of the UA-1000 will not change the setting of this switch.
For more about the ADAT mode switch, refer to “About the ADAT mode switch and external clock
switch” (p. 41).
9. External clock switch
Turn this on if you want the UA-1000 to synchronize to a word clock signal from an external device or to a digital
signal from the digital input jack. If synchronization is occurring normally, the external clock switch will light, and
the UA-1000 will be in external clock mode. If the external clock switch is blinking, synchronization has not been
achieved.
You must be sure to input a signal which has the frequency that matches the setting of the sampling frequency select
switch.
* If both the word clock input connector and the digital input connector are connected simultaneously, the word clock input
connector will take priority.
* If you are recording a digital signal, the external clock switch must be turned on.
Turning off the power of the UA-1000 will not change the setting of this switch.
For more about the external clock switch, refer to “About the ADAT mode switch and external clock
switch” (p. 41).
12
UA-1000_e.book 13 ページ 2003年8月6日 水曜日 午前11時52分
Panel Descriptions
10. Sampling frequency select switch
This selects the sampling frequency at which audio data will be recorded and played back.
In order for this setting to take effect, you must exit all applications and turn the power of the UA-1000 off, then on
again.
The sampling frequency select switch must be set to match the sampling frequency of the application you are using.
If you are using external clock mode, this must also match the sampling frequency of your external device.
* If you are using the UA-1000 in ADAT mode, set this to 44.1 kHz or 48 kHz. If this is set to anything other than 44.1 kHz or
48 kHz, ADAT mode will not be available; pressing the ADAT mode switch will not cause the ADAT mode switch to light.
USER SET
UA-1000 Control Panel (p. 36) lets you store the following settings in the UA-1000's internal memory.
• ADAT mode switch
• External clock switch
• Sampling frequency select switch
• STEREO/MONO select switch
• Direct monitor soft control switch
• Output volume select switch
• Monitor mixer and patch bay settings
To call up the settings stored in USER SET, set the sampling frequency select switch to USER SET, then cycle the
power to the unit.
For more about the internal monitor mixer and patch bay, refer to “Various settings” (p. 36).
11. STEREO/MONO select switch (Direct monitor section)
This selects whether the input signal will be monitored in stereo or in monaural.
Even if MONO is selected, the audio signal sent via USB to your computer is stereo.
Turning off the power of the UA-1000 will not change the setting of this switch.
If you have connected a mic or guitar to only one of the combo input jacks, it is convenient to use the
MONO setting.
12. Direct monitor soft control switch (Direct monitor section)
This selects whether the INPUT MONITOR will be controlled by your software. When lit, the monitor volume, pan,
and on/off settings of each input jack can be controlled from your software. When unlit, signals will be output
without being affected by any settings of the INPUT MONITOR.
This lets you temporarily disable the settings of your software in order to check the state of connections.
For details on controlling the UA-1000 from your computer, refer to “UA-1000 Control Panel” (p. 36).
Turning off the power of the UA-1000 will not change the setting of this switch.
For details, refer to “UA-1000 Control Panel” (p. 36).
fig.0db
13. Direct monitor volume (Direct monitor section)
This adjusts the volume at which the input signal is sent to the INPUT MONITOR. If you set the knob
to the 0 dB position, the volume will be the same as the signal that is being recorded.
* For details on the INPUT MONITOR, refer to “UA-1000 Control Panel” (p. 36).
If this knob is turned all the way to the left, the signal level sent to the INPUT MONITOR will be zero.
If you are “thru-ing” the audio data within your computer, or have connected a mixer and are
outputting the input signal directly from the mixer for monitoring, leave this knob turned all the way
to the left.
You can adjust the direct monitor volume even when the direct monitor soft control switch is turned
off.
13
UA-1000_e.book 14 ページ 2003年8月6日 水曜日 午前11時52分
Panel Descriptions
14. Output volume select switch
This switches the jacks that will be controlled by the output volume knob. Hold this down for two seconds or longer.
If you set this to MAIN, the knob adjusts the volume of the main output signal (i.e., all input signals plus the playback
signals from the computer mixed).
If you set this to ALL, the knob adjusts the volume of all output jacks together.
For details, refer to “Block diagram” (p. 51).
Turning off the power of the UA-1000 will not change the setting of this switch.
Lower the volume of the connected equipment before you change the setting of the output
volume select switch.
15. Output volume knob
This adjusts the final volume that is output from the UA-1000.
If the output volume knob select switch is set to MAIN, this knob adjusts the volume of the main output signal (i.e.,
all input signals plus the playback signals from the computer mixed). If you set this to ALL, the knob adjust the
volume of all output jacks together.
For details, refer to “Block diagram” (p. 51).
16. Headphone jack
A set of headphones can be connected here. The headphone jack will output the main output signal (i.e., all input
signals plus the playback signals from the computer mixed by the monitor mixer).
Sound will still be output from the master output jacks even if headphones are connected.
For details, refer to “Internal blocks of the UA-1000” (p. 36).
17. Output level indicators
These LEDs will light to indicate the output level adjusted by the output volume knob. Adjust the input sensitivity
knob of each input jack so that the red LED (CLIP) does not light.
18. Power indicator
This indicator will light when the power switch is on.
19. Power switch
fig.power-sw
Press this switch to turn the power on/off.
The power is on when the switch is in the inward position, and off
when the switch is in the outward position.
Power is on
when switch is in
Power is off
when switch is out
* Do not turn off the power switch while your audio application is recording or playing. Doing so may cause your application
to freeze.
14
UA-1000_e.book 15 ページ 2003年8月6日 水曜日 午前11時52分
Panel Descriptions
Rear panel
fig.rear
20
21
22
23
24
26
25
27
28
29
20. AC inlet
Connect the included AC cable here. Plug in the cable firmly so that it does not fall out. For details on current
consumption, refer to “Main specifications” (p. 50).
21. MIDI IN/OUT connectors
Connect these to the MIDI connectors of your MIDI device to receive or transmit MIDI messages.
22. WORD CLOCK IN/OUT jacks
Use these jacks to synchronize the UA-1000 with a digital recorder.
If you want to synchronize to WORD CLOCK, you must turn on the external clock switch.
23. USB connector
Use a USB cable to connect the UA-1000 to your computer.
* Do not plug in or unplug the USB cable while your audio application is recording or playing. Doing so may cause the
application to freeze.
24. Coaxial digital input jack / optical digital input jack
Use these jacks to input digital audio from a CD/MD/DAT, etc. If a digital device is connected to the optical digital
input jack, the optical digital input jack will be given priority; the signal from the coaxial digital input jack will not
be input. Digital signals applied to the digital input connectors are handled as INPUT 9 and 10.
In order to record a digital signal, the external clock switch must be turned on.
If you want to use the optical digital input jack to input ADAT signals, simultaneously press the ADAT mode switch
and the external clock switch to select ADAT Input/Output mode. This allows ADAT format signals to be input
from the optical input jack.
25. Coaxial digital output jack / optical digital output jack
Use these jacks to send digital audio to a digital audio device such as an MD or DAT. Digital signals output from the
digital output connectors are handled as OUTPUT 9 and 10.
If you want to use the optical digital output jack to output ADAT signals, press the ADAT mode switch to select
ADAT Output mode, or simultaneously press the ADAT mode switch and the external clock switch to select
ADAT Input/Output mode. This allows ADAT format signals to be output from the optical input jack.
26. Input jacks 5–8
Connect to these jacks when you want to input audio signals from audio devices or MIDI sound modules.
15
UA-1000_e.book 16 ページ 2003年8月6日 水曜日 午前11時52分
Panel Descriptions
27. Insertion / Input jacks 1–4
These can be used either as insertion jacks or as input jacks.
Turn the Insertion/Input Select switches on/off to select whether these jacks will function as insertion jacks or as
input jacks.
For details, refer to “Inserting an external effects processor” (p. 32).
28. Insertion / Input jack select switches
Turn the Insertion/Input Select switches on/off to select whether insertion / input jacks 1–4 will function as insertion
jacks or as input jacks.
For details on use, refer to “Inserting an external effects processor” (p. 32).
Insertion jack mode:
Set the switch to INSERT (
button outward). Insertion/Input jacks 1–4 will function as insertion jacks.
This setting lets you insert external effects processors into the inputs of combo input jacks 1–4 (TRS phone type).
Input jack mode:
Set the switch to INPUT ( button inward). Insertion/Input jacks 1–4 will function as input jacks.
This setting lets you input audio signals from audio devices or MIDI sound modules (+4 dBu fixed, phone type,
unbalanced).
If you use these as input jacks, the input from combo input jacks 1–4 will be turned off.
See also “Inserting an external effects processor” (p. 32).
29. Output jacks 1–8 (phone)
These are output jacks for analog audio signals.
16
UA-1000_e.book 17 ページ 2003年8月6日 水曜日 午前11時52分
Application of AC230 V
Power Cord
for UK
except for UK
17
UA-1000_e.book 18 ページ 2003年8月6日 水曜日 午前11時52分
Preparations for using the UA-1000
Installing the driver
What is a driver?
A “driver” is software that transfers data between the UA-1000 and application
software running on your computer, when your computer and the UA-1000 are
connected by a USB cable. The driver sends data from your application to the UA1000, and from the UA-1000 to your application.
1
With the UA-1000 disconnected, start up Windows.
Disconnect all USB cables except for a USB keyboard and USB mouse (if used).
If you are using virus checking or similar software, be sure to exit it as well.
2
Open the System Properties dialog box.
You must log on using a user
name with an administrative
account type (e.g.,
Administrator). For details on
user accounts, please consult
the system administrator of
your computer.
1. Click the Windows start menu, and from the menu, select Control Panel.
2. In “Pick a category,” click “Performance and Maintenance.”
3. In “or pick a Control Panel icon,” click the System icon.
fig.2-1
3
Click the Hardware tab, and then
click [Driver Signing].
Depending on how your
system is set up, the System
icon may be displayed directly
in the Control Panel (the
Classic view). In this case,
double-click the System icon.
The Driver Signing Options dialog box
will appear.
4
Make sure that “What action do
you want Windows to take?” is set
to “Ignore.”
If it is set to “Ignore,” simply click [OK].
If it is not set to “Ignore,” make a note of
the current setting (“Warn” or “Block”).
Then change the setting to “Ignore” and
click [OK].
5
6
Click [OK] to close the System Properties dialog box.
Exit all currently running software (applications).
Also close any open windows. If you are using virus checking or similar software, be
sure to exit it as well.
18
If you changed “What action
do you want Windows to
take?,” you must restore the
previous setting after you have
installed the driver.
UA-1000_e.book 19 ページ 2003年8月6日 水曜日 午前11時52分
Preparations for using the UA-1000
7
Prepare the CD-ROM.
Insert the CD-ROM into the CD-ROM drive of your computer.
8
Click the Windows start button. From the menu that appears, select
“Run...”
The “Run...” dialog box will appear.
fig.2-3
9
In the dialog box that appears, input
the following into the “Open” field,
and click [OK].
If the screen indicates
“Windows can perform the
same action each time you
insert a disk or connect a
device with this kind of file,”
click [Cancel].
To check the drive name
Click the start button, and
choose My Computer from the
menu that appears. In the
window that appears, check
the drive name of the CDROM drive into which you
inserted the CD-ROM in step
7. The drive name is the (D:) or
(E:) displayed by the CD-ROM
drive
.
(drive name) :\Driver\USB_XP\SETUPINF.EXE
* In the explanatory example shown here, the drive name is given as “D:”. The drive name
“D:” may be different for your system. Specify the drive name of your CD-ROM drive.
10
The SetupInf dialog box will appear.
You are now ready to install the driver.
11
Use the USB cable to connect the UA-1000 to your computer.
1. With the power switch turned OFF, connect the power cord to the UA-1000.
2. Connect the power cord to an electrical outlet.
3. Use the USB cable to connect the UA-1000 to your computer.
12
Set the UA-1000’s power switch to the ON position.
Near the task bar, your computer will indicate “Found New Hardware.” Please
wait.
13
Once the connections have
been completed, turn on
power to your various devices
in the order specified. By
turning on devices in the
wrong order, you risk causing
malfunction and/or damage to
speakers and other devices.
This unit is equipped with a
protection circuit. A brief
interval (a few seconds) after
power up is required before
the unit will operate normally.
The Found New Hardware Wizard will appear.
Select “Install from a list or specific location (Advanced),” and click [Next].
19
UA-1000_e.book 20 ページ 2003年8月6日 水曜日 午前11時52分
Preparations for using the UA-1000
fig.2-7_30
14
The screen will indicate “Please
choose your search and
installation options.”
Select “Don’t search. I will choose the
driver to install,” and click [Next].
15
Make sure that the “Model” field indicates “EDIROL UA-1000,” and click
[Next]. Driver installation will begin.
If the “What action do you want Windows to take?” setting was not set to “Ignore,” a “Hardware
Installation” dialog box will appear.
If “What action do you want Windows to take?” is set to “Warn”
A dialog box with a “!” symbol will appear.
1. Click [Continue Anyway].
2. Continue the installation.
If “What action do you want Windows to take?” is set to “Block”
A dialog box with a “x” symbol will appear.
1. Click [OK].
2. When the “Found New Hardware Wizard” appears, click [Finish].
3. Return to step 1 (p. 18) and re-install the driver from the beginning of the procedure.
16
The Insert Disk dialog box may appear.
Click [OK].
17
The Insert Disk dialog may
not appear. In that case,
proceed to the next step.
The Files Needed dialog box will appear.
Input the following into the “Copy files from” field, and click [OK].
D:\DRIVER\USB_XP
* The drive name “D:” may be different for your system. Specify the drive name of your CDROM drive.
If the “What action do you want Windows to take?” setting was not set to “Ignore,” a “Hardware
Installation” dialog box will appear.
A dialog box with a “!” symbol will appear.
1. Click [Continue Anyway].
2. Continue the installation.
20
UA-1000_e.book 21 ページ 2003年8月6日 水曜日 午前11時52分
Preparations for using the UA-1000
18
The screen will indicate “Completing the Found New Hardware Wizard.”
Click [Finish].
Wait until “Found New Hardware” appears near the taskbar.
19
When driver installation has been completed, the System Settings
Change dialog box will appear.
Click [Yes]. Windows will restart automatically.
If you changed the “What action do you want Windows to take? setting, restore the original setting after
Windows restarts.
1. Log on to Windows using the user name of an administrative account (e.g., Administrator).
2. Click the Windows start button, and from the menu that appears, select Control Panel.
3. In “Pick a category,” click “Performance and Maintenance.”
4. In “or pick a Control Panel icon,” click the System icon. The System Properties dialog box will
appear.
*
Depending on how your system is set up, the System icon may be displayed directly in the Control Panel
(classic view). In this case, double-click the System icon.
5. Click the Hardware tab, and then click [Driver Signing]. The Driver Signing Options dialog box
will appear.
6. Return the What action do you want Windows to take? setting to the original
setting (either “Warn” or “Block”), and click [OK].
7. Click [OK]. The System properties dialog box will close.
This completes installation of the driver.
Next, make settings so that Windows will give priority to background services, to
ensure that audio and MIDI data are processed smoothly.
(-> “Giving priority to background services” (p. 22))
21
UA-1000_e.book 22 ページ 2003年8月6日 水曜日 午前11時52分
Preparations for using the UA-1000
Giving priority to background services
If you fail to make this setting, you may experience interruptions in the sound. To
ensure that audio MIDI and processing occurs smoothly, use the following
procedure to make settings.
1
Open the System Properties dialog box.
1. Click the Windows start menu, and from the menu, select Control Panel.
2. In “Pick a category,” click “Performance and Maintenance.”
3. In “or pick a Control Panel icon,” click the System icon.
2
Click the Advanced tab.
fig.background
3
At the right of the Performance
field, click [Settings].
The Performance Options dialog box
will appear.
4
5
6
Click the Advanced tab.
In the Processor Scheduling field,
select “Background services,” and
click [OK].
In the System Properties dialog box, click [OK].
The System Properties dialog box will close.
Next, make audio device and MIDI device settings.
(->“Driver settings” (p. 23))
22
UA-1000_e.book 23 ページ 2003年8月6日 水曜日 午前11時52分
Preparations for using the UA-1000
Driver settings
About the input/output devices
In order to obtain the best performance from the software you are using, you must specify the correct audio and MIDI
input/output destinations.
The audio driver supports WDM/ASIO2.0/MME.
Audio device
Audio output device
Audio input device
ASIO audio device
EDIROL UA-1000
MME EDIROL UA-1000 1-2 Out
:
MME EDIROL UA-1000 9-10 Out
EDIROL UA-1000
MME EDIROL UA-1000 1-2 In
:
MME EDIROL UA-1000 9-10 In
MME EDIROL UA-1000 Mon
EDIROL UA-1000
WDM
MME
WDM
MME
ASIO
MIDI device
MIDI OUT device
MIDI IN device
EDIROL UA-1000
If you specify UA-1000 MIDI OUT as the output port for your sequencer software,
messages will be transmitted from the MIDI OUT connector of the UA-1000 itself.
EDIROL UA-1000
If you specify UA-1000 MIDI IN as the input port for your sequencer software, messages will be input from the UA-1000’s MIDI IN connector.
If you are unable to select the UA-1000 device in the device settings of your software, it is
possible that the UA-1000 driver was not installed correctly. Please reinstall the driver.
WDM
Use this for the following applications or purposes.
• Conventional applications such as Media Player
(For details on settings, refer to “Settings when using the Windows Media Player”).
• WDM driver mode compatible applications such as SONAR
• DirectSound compatible applications
• Playing back WMA Professional format 5.1 channel files in Media Player
(In “Control Panel” -> “Sounds and Audio Devices” -> “Audio” tab -> “Advanced” button in “Sound playback” ->
“Speaker setup,” select “5.1 surround sound speakers”)
* Stereo audio signals will be input and output from WAVE OUT 1-2 and WAVE IN 1-2. In other cases, use “MME.”
ASIO
Use this when using the UA-1000 with an ASIO-compatible application such as Cubase.
In the ASIO settings of your application, select “EDIROL UA-1000.” You will be able to use 12 inputs and 10 outputs.
* To prevent audio loops or double monitoring, turn off monitoring in your application or select “Use ASIO Direct Monitor.”
* When using the UA-1000 with ASIO, we recommend that you set your application so that it does not use the Microsoft GS Wavetable
SW Synth. (In order to decrease the load, and for convenience when changing the driver buffer size)
MME
Normally you should use WDM or ASIO.
Use this in the following cases when using an application that does not support WDM driver mode or ASIO (e.g., Cool Edit).
• Recording or playing 24-bit data
• Using something other than the UA-1000’s WAVE OUT 1-2 and WAVE IN 1-2
23
UA-1000_e.book 24 ページ 2003年8月6日 水曜日 午前11時52分
Preparations for using the UA-1000
Input/output device settings
If you are using the UA-1000 with the Media Player included with Windows, use the
following procedure to make input/output device settings.
The method for making device settings will depend on the software you are using.
For details, refer to the owner's manual for your software.
1
Open the Sounds and Multimedia Properties dialog box.
1. Click the Windows start menu, and from the menu, select Control Panel.
2. In “Pick a category,” click “Sound, Speech, and Audio Devices.”
3. In “or pick a Control Panel icon,” click the Sounds and Audio Devices icon.
2
Depending on how your
system is set up, the sounds
and Audio Devices icon may
be displayed directly in the
Control Panel (the Classic
view). In this case, double-click
the Sounds and Audio
Devices icon.
Click the Audio tab.
fig.sound
3
In Sounds and Audio Devices
Properties, click each Default device
field and choose the following device
from the list that appears.
Sound playback
Sound recording
MIDI music
playback
4
EDIROL UA-1000
EDIROL UA-1000
EDIROL UA-1000
Click [OK] to close the Sounds and
Multimedia Properties dialog box.
The completes the driver settings.
24
If you are using sequencer
software, you will need to
make audio and MIDI device
settings in your software. For
details, refer to the owner's
manual for your software.
UA-1000_e.book 25 ページ 2003年8月6日 水曜日 午前11時52分
Preparations for using the UA-1000
Check whether there is sound
Now we will play back the sample data to check whether connections and settings
are correct.
Here we will use standard Windows functionality to play back the sample data. The
sample data is found on the CD-ROM.
Use of the song data supplied with this product for any purpose other than
private, personal enjoyment without the permission of the copyright
holder is prohibited by law. Additionally, this data must not be copied, nor
used in a secondary copyrighted work without the permission of the
copyright holder.
1
2
3
Insert the CD-ROM into the CD-ROM drive of your computer.
From the SampleSong folder of the CD-ROM, drag TTears(.mp3) to your
desktop, copying it.
What you actually see on your
computer screen may be
different depending on your
computing environment and
the operating system your
using.
Right-click the copied file TTears(.mp3), and select Play.
Play back the sample data.
Click the Preview tab, and then click the button.
If it did not play back correctly,
refer to “Troubleshooting” (p.
45) to determine the reason.
If it was played back correctly, this means that the computer and the UA-1000 are
connected correctly and that the drivers have been installed correctly.
About the demo songs
When playing the demo songs (other than the MP3 songs) in the SampleSong folder of the CD-ROM, please
note the following points to ensure that the songs play correctly.
Copy the demo songs to the hard disk of your computer, and then load them into your sequencer for playback.
• The demo songs were produced at 48 kHz. Set the UA-1000's sampling frequency to 48 kHz. If
you change the sampling frequency, you need to switch off the UA-1000, then turn it back on
again.
• If you use the Cubase SX demo version to play back the Cubase demo songs, the playback will
not be correct, since some functions, such as effects, will not be available.
25
UA-1000_e.book 26 ページ 2003年8月6日 水曜日 午前11時52分
Basic connections and settings
This chapter explains basic connections for the UA-1000 and describes the data flow.
* To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn
off the power on all devices before making any connections.
Basic connections
Use a USB cable to connect the UA-1000 to your computer.
Connecting the USB cable allows both MIDI data and audio data to be transferred.
As shown in the diagram, you can connect headphones and/or monitor speakers to monitor the playback of
your software or the sound of the instruments or audio devices connected to the UA-1000.
Amplified
speakers
Computer
fig.b
asic
In the OUTPUT PATCH BAY
section of UA-1000 Control
Panel, set OUTPUT 1-2 to
“MONITOR OUT.”
USB cable
(->“Various settings” (p. 36))
USB
Headphones
When using a mixer
fig.m
ixer
Mixer
In the OUTPUT PATCH BAY
section of UA-1000 Control
Panel, set OUTPUT 1-2 to
WAVE OUT 1-2, OUTPUT 34 to WAVE 3-4 ... OUTPUT 78 to WAVE 7-8.
Computer
USB cable
USB
About the sampling frequency select switch
• You must set the UA-1000’s sampling frequency select switch to the sampling frequency
used by your software.
• After you change the setting of the sampling frequency select switch, you must switch off the
UA-1000, then turn it on again.
26
UA-1000_e.book 27 ページ 2003年8月6日 水曜日 午前11時52分
Basic connections and settings
Recording a mic or guitar
With the setup shown below, you can listen to the audio data played back by your computer while you
perform on the guitar (or mic), and record only the guitar (or vocal) performance on your computer.
fig.mic-guitar
Guitar/bass
Connect to
INPUT 3
Hi-Z on
PAD off
Adjust the input level
Specify the sampling frequency
● Connections
The sound of the device connected to INPUT 1 will be recorded on the left (L) channel of your computer. If
you connect to INPUT 2, the sound will be recorded on the right (R) channel.
Connect your guitar to INPUT 3.
● Sampling frequency select switch
Set this to the sampling frequency that is selected in your recording software.
● Input impedance select switch
If using a mic
select Lo-Z.
If using a guitar
select Hi-Z.
● STEREO/MONO select switch (Direct monitor section)
Set this to specify whether you will monitor the input signal in stereo or in monaural.
● Direct monitor soft control switch
Turn this on if you want to control the INPUT MONITOR from your software.
For details, refer to “UA-1000 Control Panel” (p. 36).
● Direct monitor volume
Adjust the monitor volume appropriately.
● Phantom power switch
If you are using a condenser mic, turn the phantom power switch on.
* If you have connected a device that does not require phantom power, you must turn off the phantom power
switch; failing to do so will damage your equipment.
27
UA-1000_e.book 28 ページ 2003年8月6日 水曜日 午前11時52分
Basic connections and settings
● Input sensitivity knob
Use the input sensitivity knob to adjust the input level. To obtain the best audio quality, adjust the input
sensitivity knob until the level is as high as you can get it without causing the input peak indicator to light.
● Output volume select switch
Select either MAIN or ALL.
If you select MAIN, you will be able to adjust the volume of the main output signal (all input signals and the
playback signals from the computer mixed).
If you select ALL, you will be able to adjust the volume of all output jacks together.
Lower the volume of your connected equipment before you change the setting of the output
volume select switch.
● Other cautions
Do not connect anything to input jacks you are not using.
Howling could be produced depending on the location of microphones relative to speakers. This can be
remedied by:
1. Changing the orientation of the microphone(s).
2. Relocating microphone(s) at a greater distance from speakers.
3. Lowering volume levels.
28
UA-1000_e.book 29 ページ 2003年8月6日 水曜日 午前11時52分
Basic connections and settings
Recording onto an external ADAT device
fig.adat-out
INPUT
Optical cable
OPTICAL OUT
● Connections
Connect an optical cable from the OPTICAL OUT jack.
● Sampling frequency select switch
Select either 44.1 kHz or 48 kHz.
● ADAT mode switch
Press the ADAT mode switch to turn it on.
* By pressing the external clock mode switch in ADAT mode, you can use ADAT Output mode to
synchronize the word clock or digital input to an external device.
If you turn on the external synchronization mode switch when using ADAT output mode, the output to the
ADAT will be synchronized to the word clock from the external device or to the clock of the digital input.
fig.adat-out2
INPUT
OPTICAL OUT
WORD CLOCK IN
* If the word clock input connector and the digital input connector are both connected, the word
clock input connector will take priority for synchronization.
29
UA-1000_e.book 30 ページ 2003年8月6日 水曜日 午前11時52分
Basic connections and settings
Capturing sound from an external ADAT device
fig.basic
OUTPUT
Optical cable
OPTICAL IN
Set the sampling
frequency
● Connections
Connect an optical cable to the OPTICAL IN jack.
● Sampling frequency select switch
Select either 44.1 kHz or 48 kHz.
Set this to the same sampling frequency as specified for your ADAT or recording software.
● ADAT mode switch and external clock switch
fig.adat-sig
Simultaneously press the ADAT mode
switch and external clock switch.
The PEAK/SIG/ADAT IN indicators
will light orange simultaneously.
Press simultaneously
Lit (orange)
fig.adat-sig2
When audio signals are input from the
ADAT to the UA-1000, the PEAK/
SIG/ADAT IN indicators will light
green.
Lit (green)
* If the word clock input connector is connected, the word clock input connector will take priority for
synchronization. In this case, the ADAT connected to the digital input connector must also be synchronized
to the word clock.
30
UA-1000_e.book 31 ページ 2003年8月6日 水曜日 午前11時52分
Basic connections and settings
Monitoring 5.1 channel sound
fig.51ch
5.1ch speaker
system
ALL
● Connections
Connect phone jack audio cables to the output jacks.
● Output volume select switch
Press the output volume select switch to select ALL (lit).
● Output volume knob
Use the knob to adjust the volume level of signal that is output from the output jacks.
● UA-1000 internal patching
Set patch bay as follows in UA-1000 Control Panel.
* For details on UA-1000 Control Panel, refer to “Various settings” (p. 36).
In the PATCH BAY area of UA-1000 Control Panel set OUTPUT 1-2 to WAVE OUT 1-2, OUTPUT 3-4 to
WAVE OUT 3-4, OUTPUT 5-6 to WAVE OUT 5-6.
Settings in Windows
1. From the Windows Control Panel, open Sound and Audio Devices Properties.
(-> “Input/output device settings” (p. 24))
2. Click the Audio tab.
In Sound Playback, click the Default Device field, and choose EDIROL UA-1000 from the list that
appears.
3. In Sound Playback, click [Advanced].
4. Click the Speakers tab.
Select 5.1 surround sound speakers as Speaker setup.
5. Click [OK] to close the Advanced Audio Properties dialog box.
6. Click [OK] to close the Sounds and Audio Devices Properties dialog box.
*
In your software, select 6-speaker mode, 5.1 ch surround sound mode, etc.
31
UA-1000_e.book 32 ページ 2003年8月6日 水曜日 午前11時52分
Basic connections and settings
Inserting an external effects processor
If you want to use an external effects processor to process the sound of a mic or guitar being input from each
inputs, you can use the rear panel insertion/input jacks 1–4 as insertion jacks.
fig.insert
Red
OUTPUT
External effect processor
PCS-31 (sold separately)
INSERT
INPUT
White
● Connections
Connect insertion cables to the rear panel insertion/input jacks 1–4, and connect the other end of the cable
to your external effects processor.
You will need to use special insertion cables. (Sold separately: Roland PCS-31)
● Insertion/Input jack select switch
Since you will be using insertion/input jacks 1--4 as insertion jacks, select INSERT ( (
Signal flow
fig.insert-flow
External effect processor
OUTPUT
INPUT
Rear
OUTPUT
INSERT 1
UA-1000
Front
INPUT 1
Signal flow
32
button outward).
UA-1000_e.book 33 ページ 2003年8月6日 水曜日 午前11時52分
Basic connections and settings
Recording a digital input signal
fig.digital
CD/MD/DAT player,
hard disk recorder, etc.
Connect to the OPTICAL/COAXIAL
IN jack of the appropriate type
Select the same sampling
Select the same sampling frequency as
your digital audio playback device
ON (lit)
● Connections
Connect your digital audio device to either the coaxial digital input jack or the optical digital input jack, as
appropriate for your device.
● Sampling frequency select switch
Set this to the same frequency as selected on your digital playback device and your recording software.
● External clock switch
So that the UA-1000 will synchronize to the digital signal being input to the digital input jack, turn this on (lit).
● Direct monitor soft control switch
Turn this on if you want to control the INPUT MONITOR from your software.
For details, refer to “UA-1000 Control Panel” (p. 36)
● Direct monitor volume
Adjust the volume appropriately.
33
UA-1000_e.book 34 ページ 2003年8月6日 水曜日 午前11時52分
Basic connections and settings
Synchronizing to the word clock input
Word clock and sampling frequency
An analog audio signal is converted into a digital audio signal by sampling the level of the analog signal at
extremely small increments of time, and converting this level into digital data. The sampling frequency is the
number of times this AD (analog to digital) conversion is performed each second. Higher sampling
frequencies allow better audio quality, but will also increase the amount of data.
In order for two or more devices to accurately process a digital audio signal, all of the devices must be
operating at the identical sampling frequency. This can be ensured by sending a word clock signal to the
devices. In order for two or more devices to be synchronized, they must be in the appropriate Word Clock
Master and Word Clock Slave relationship.
Using the UA-1000 as the master
In the setup shown here, the UA-1000 is the master, and the external device (e.g., hard disk recorder) is the
slave.
fig.synchro-master
Hard disk recorder, etc.
WORD CLOCK
OUT
Set the sampling frequency
Match the sampling frequency
of the hard disk recorder
OFF
(unlit)
● Connections
Connect the WORD CLOCK OUT jack to your hard disk recorder.
● Sampling frequency select switch
Set this to the same sampling frequency as selected on your hard disk recorder and recording software.
● External clock switch
Turn this off (unlit) so that the external device will synchronize to the digital signal output from the UA-1000
(i.e., the UA-1000 will be the master).
34
UA-1000_e.book 35 ページ 2003年8月6日 水曜日 午前11時52分
Basic connections and settings
Using an external device as the master
In the setup shown here, the hard disk recorder or other external device is the master, and the UA-1000 is the
slave.
fig.synchro-slave
Hard disk recorder, etc.
WORD CLOCK
IN
Set the sampling frequency
Match the sampling frequency of
the master device
ON (lit)
● Connections
Connect your external device (e.g., hard disk recorder) to the WORD CLOCK IN jack.
● Sampling frequency select switch
Set this to the same sampling frequency as selected for the master device.
● External clock switch
Turn this on (lit) so that the UA-1000 will synchronize to the digital signal input to the WORD CLOCK IN
connector (i.e., the UA-1000 will be the slave).
35
UA-1000_e.book 36 ページ 2003年8月6日 水曜日 午前11時52分
Various settings
You can make various settings for the UA-1000 from your computer.
Use UA-1000 Control Panel to make settings. This lets you control the UA-1000’s monitor mixer on/off,
volume, on/off, and pan settings. You can also specify the patching.
In addition, you can make the settings described in “Adjusting the audio latency” (p. 40) and “Using ASIO
Direct Monitor” (p. 40).
Internal blocks of the UA-1000
The UA-1000 contains two types of mixer and two patch bays.
fig.int-block
WAVE IN
MIXER
WAVE OUT
MONITOR OUT
1-2
WAVE OUT
MONITOR
1-2
main output signal
PHONES
Direct monitor
volume
(front panel)
INPUT
MONITOR
(DIRECT
MONITOR)
Output volume knob
(front panel)
1-2
1-2
1-10
1-10
INPUT 1-10
OUTPUT 1-10
OUTPUT
PATCH BAY
WAVE IN
PATCH BAY
1-10
PATCH BAY
For details, refer to “Block diagram” (p. 51).
UA-1000 Control Panel
UA-1000 Control Panel is installed together with the driver when you install the UA-1000 Driver.
Here we will provide only an overview. For details, refer to the README_E.HTM file the Driver -> USB_XP
folder of the CD-ROM.
Starting up
1. From the Windows start menu, choose Control Panel.
2. Click “Switch to Classic View” to select the Classic view. Depending on your system, Classic
view may already be selected. If so, proceed to the next step.
fig.ctrl
3. In the Control Panel, double-click the EDIROL UA-1000 icon.
The UA-1000 Control Panel will appear.
36
UA-1000_e.book 37 ページ 2003年8月6日 水曜日 午前11時52分
Various settings
Screen items and what they do
Main window
fig.control
WAVE IN
PATCH BAY
OUTPUT
PATCH BAY
INPUT
MONITOR
(DIRECT
MONITOR)
WAVE OUT
MONITOR
MONITOR OUT
Device Panel
You can use UA-1000 Control Panel to control each block of the UA-1000.
fig.int-block2
MONITOR
OUT
MIXER
INPUT
MONITOR
(DIRECT
MONITOR)
1-2
WAVE OUT
MONITOR
WAVE OUT
MONITOR
1-2
PHONES
INPUT
MONITOR
(DIRECT
MONITOR)
1-2
1-2
1-10
1-10
INPUT 1-10
OUTPUT 1-10
OUTPUT
PATCH BAY
WAVE IN
PATCH BAY
1-10
PATCH BAY
WAVE IN
PATCH BAY
OUTPUT PATCH
BAY
37
UA-1000_e.book 38 ページ 2003年8月6日 水曜日 午前11時52分
Various settings
WAVE IN PATCH BAY
Here you can select the input source audio signals that will be sent to the computer. Choose from the five
stereo channels of audio data sent from the computer, the audio data input from the UA-1000’s input jacks 1–
10, and MONITOR OUT to specify the channels that will be sent to the computer.
OUTPUT PATCH BAY
Here you can select the signals that will be sent to each output jack of the UA-1000. For each output jack, you
can choose from the five stereo channels of audio data sent from the computer, the audio data from the UA1000's input jacks 1–10, and MONITOR OUT.
fig.0db-1
INPUT MONITOR (DIRECT MONITOR)
Here you can control the monitor level and balance of the audio data that is input
from the UA-1000's input jacks 1–10.
These settings will be ignored if the front panel Direct Monitor Soft Control switch
is off.
WAVE OUT MONITOR
This controls the balance of the five stereo channels of audio data sent from the computer, and sends the
resulting signal to the monitor section (e.g., headphones).
Device Panel
This area shows the state of the various panel switches of the device.
When you click a setting button, the panel switch setting window will appear.
Writing to USER SET
From UA-1000 Control Panel you can write the following settings into the UA-1000’s internal memory (USER
SET), and recall them when desired.
• ADAT mode switch
• External Clock switch
• Sampling frequency selection
• STEREO/MONO select switch
• Direct Monitor Soft Control switch
• Output volume select switch
• Monitor mixer and patch bay settings
1. Start up UA-1000 Control Panel.
(->“Starting up” (p. 36))
2. From the Device menu, choose Store USER SET of Device.
Make the appropriate settings in the dialog box that appears.
3. Click [OK] to write the settings to the USER SET.
4. The USER SET settings will be loaded when you power-on the UA-1000 with its sampling
frequency select switch to USER SET.
The UA-1000 supports 192 kHz playback.
STEPS
1. If the UA-1000’s USER SET has already been modified, restore it to the factory settings (p. 44).
2. Set the UA-1000’s sampling frequency select switch to USER SET, and power-on the UA-1000.
* 192 kHz recording is not supported.
* You will be able to output only to output jacks 1/2 and the headphone jack.
38
UA-1000_e.book 39 ページ 2003年8月6日 水曜日 午前11時52分
Various settings
Reading and writing memories
Five sets of UA-1000 settings can be stored within the UA-1000 itself. These stored memories can be read and
written from UA-1000 Control Panel.
For the procedure, refer to README_E.HTM on the included CD-ROM.
Convenient ways to use the OUTPUT PATCH BAY
You can store two different settings for the OUTPUT PATCH BAY, and switch between these two settings.
DIRECT MONITOR: ON
fig.monitor-on
If even one INPUT MONITOR (DIRECT MONITOR) switch is ON,
the DIRECT MONITOR: ON settings of the OUTPUT PATCH BAY
will be used.
* These settings will always be used if the Direct Monitor Soft Control switch
of the UA-1000’s front panel is turned off.
DIRECT MONITOR: OFF
fig.monitor-off
If all of the INPUT MONITOR (DIRECT MONITOR) switches are
OFF, the DIRECT MONITOR: OFF settings of the OUTPUT PATCH
BAY will be used.
Examples of use
Simply by switching INPUT MONITOR (DIRECT MONITOR) on/off, you can switch between settings for
monitoring and settings for mastering.
fig.output-monitor
Settings for monitoring
These settings are appropriate when you
want to hear the sounds being input to the
UA-1000 from the input jacks.
fig.output-monitor2
Settings for mastering
These settings are appropriate when you
have finished acquiring audio from the
input jacks, and are mastering the data on
your computer.
39
UA-1000_e.book 40 ページ 2003年8月6日 水曜日 午前11時52分
Various settings
Adjusting the audio latency
You can change the driver settings to adjust the latency of the audio. To adjust the latency, change the Buffer
Size in the driver settings dialog box. Latency is the time delay from when an application plays back audio
data until the sound is actually heard from an audio device such as the UA-1000.
1. In UA-1000 control panel, click the Driver menu, select Driver settings.
Open the “Driver Settings” dialog box.
Adjust the driver buffer size.
fig.driver-set
2. Set “Audio Buffer Size” to the far left (Min).
Click [OK] to close the driver settings dialog box.
3. Restart the application that is using the UA-1000.
If you are using an application that has a function for
testing audio devices, get it to perform its tests.
4. Play back audio data on your application.
If interruptions occur in the sound, repeat this procedure,
and gradually increase the buffer size specified in step 2
until interruptions no longer occur.
* Depending on the application you are using, there may be a buffer size or latency adjustment function among the audio
settings of the application as well. For details, refer to the operation manual for your application.
Using ASIO Direct Monitor
If you are using the UA-1000 in Advanced mode from an ASIO 2.0 compatible application, the UA-1000’s
Input Monitor select switch can be controlled from your ASIO 2.0 compatible application.
1. In UA-1000 control panel, click the Driver menu, select Driver settings.
Open the “Driver Settings” dialog box.
fig.driver-set
2. Check the “Use ASIO Direct Monitor” check box.
3. Click [OK] to close the driver settings dialog box.
* Depending on your application, there may also be an ASIO Direct Monitor setting among the audio settings of your
application. For details, refer to the operation manual for your application.
* When using ASIO Direct Monitor, monitoring may switch on/off at unexpected times, depending on the application
settings and on the recording procedure. If this occurs, uncheck the check box in step 2 to disable ASIO Direct Monitor.
40
UA-1000_e.book 41 ページ 2003年8月6日 水曜日 午前11時52分
Synchronization settings
About the ADAT mode switch and external clock switch
■ ADAT mode switch
ADAT Output mode
fig.adat-on
When you press the ADAT mode switch, the ADAT mode switch will
light, and the UA-1000 will be in ADAT Output mode.
The signals being output to jacks 1–8 will be converted to ADAT
format and sent from the optical digital output jack. The signals will
simultaneously be sent from output jacks 1–8 as well.
* You can use the digital input jack (coaxial, optical) and analog input jacks as usual.
* The coaxial digital output jack will not be available.
* Set the sampling frequency select switch and the sampling frequency setting of your application to
44.1 kHz or 48 kHz. If a setting other than 44.1 kHz or 48 kHz is selected, ADAT mode will not be available;
pressing the ADAT mode switch will not place the unit in ADAT mode, nor will the ADAT mode switch
light.
fig.adat-ext-on
While in ADAT mode, you can press the external clock switch to
synchronize the word clock or digital input to an external device in
ADAT mode.
Internal blocks in ADAT output mode
fig.int-blockA
WAVE IN
WAVE OUT
MIXER
MONITOR OUT
1-2
WAVE OUT
MONITOR
Direct monitor
volume
(front panel)
1-2
main output signal
Headphone
jack
PHONES
INPUT
MONITOR
(DIRECT
MONITOR)
Output volume knob
(front panel)
1-2
1-2
Input jacks
(phone)
Output digital
input jack
1-10
1-10
INPUT 1-8
OUTPUT 1-8
Output jacks
(phone)
OUTPUT 1-8
Optical digital
output jack
OUTPUT
PATCH BAY
INPUT 9-10
WAVE IN
PATCH BAY
1-10
ADAT format
PATCH BAY
41
UA-1000_e.book 42 ページ 2003年8月6日 水曜日 午前11時52分
Synchronization settings
ADAT Input mode
Simultaneously press the ADAT mode switch and the External Clock mode switch. The peak indicator will
light in orange, and the UA-1000 will be in ADAT Input mode. The outputs will operate in the same way as
in ADAT Output mode.
* If the word clock input connector is connected, the word clock input connector will take priority for
synchronization. If the UA-1000 is operating in synchronization to the word clock, the ADAT compatible
device connected to digital input must be synchronized to the word clock.
* Set the sampling frequency select switch and the sampling frequency setting of your software to 44.1 kHz or
48 kHz. If a setting other than 44.1 kHz or 48 kHz is selected, ADAT mode will not be available; pressing
the ADAT mode switch will not cause the ADAT mode switch to light.
* If the external clock switch is blinking, synchronization has not been achieved. The UA-1000 will not be able
to record or play back correctly. Please check the settings of the connected equipment.
Possible reasons for problems
• The digital signal from the connected ADAT compatible device is not being received correctly.
• If a word clock is being input to the word clock input connector in ADAT mode, the word
clock signal is not being received correctly, or the sampling frequency of the word clock is not
44.1 kHz or 48 kHz.
* Turning off the power of the UA-1000 will not change the setting of this switch.
* The coaxial digital and analog input jacks will not be available.
fig.adat-off
While in ADAT Input mode, pressing the ADAT switch will exit
ADAT mode and enter External Clock mode.
fig.adat-ext-off
While in ADAT Input mode, pressing the External Clock mode switch
will exit ADAT Input mode and enter ADAT Output mode.
42
UA-1000_e.book 43 ページ 2003年8月6日 水曜日 午前11時52分
Synchronization settings
Internal blocks in ADAT input mode
fig.int-blockB
WAVE IN
WAVE OUT
MIXER
MONITOR OUT
1-2
WAVE OUT
MONITOR
Direct monitor
volume
(front panel)
1-2
main output signal
Headphone
jack
PHONES
INPUT
MONITOR
(DIRECT
MONITOR)
Output volume knob
(front panel)
1-2
1-2
1-8
Input jacks
(phone)
1-10
INPUT 1-8
Output digital
input jack
OUTPUT 1-8
Output jacks
(phone)
OUTPUT 1-8
Optical digital
output jack
OUTPUT
PATCH BAY
INPUT 1-8
ADAT format
WAVE IN
PATCH BAY
1-10
ADAT format
PATCH BAY
■ External clock switch
Turn this switch on if you want the UA-1000 to synchronize to the word clock from an external digital device
or to the digital signal being input from the digital input jack. If synchronization is occurring correctly, the
external clock switch will light, and the UA-1000 will be in external clock mode.
If you are synchronizing to the digital signal or recording it, you must turn on the external clock switch.
If the external clock switch is blinking, synchronization has not been achieved. The UA-1000 will not be able
to record or play back correctly. Please check the settings of the connected equipment.
Possible reasons for problems
• The word clock from the connected digital device or the digital signal from the digital input jack is
not being received correctly
• The sampling frequency does not match the setting of the sampling frequency select switch.
If the word clock input connector and the digital input connector are both connected, the word clock input
connector will take priority.
If the UA-1000 is synchronized to the word clock, the digital device connected to the digital input jack must
also be synchronized to the word clock.
If the digital device connected to the digital input is not synchronized to the word clock, the digital
input and digital output will not operate correctly.
* Turning off the power of the UA-1000 will not change the setting of this switch.
43
UA-1000_e.book 44 ページ 2003年8月6日 水曜日 午前11時52分
System settings
Restoring the factory settings (Factory Reset)
fig.system
1.
While simultaneously holding down the output volume select
switch and the STEREO/MONO select switch, turn on the
power.
The output volume select switch and the STEREO/MONO select
switch will blink.
2.
Press the STEREO/MONO select switch once again.
Hold down simultaneously
and turn on the power
The output volume select switch and the STEREO/MONO select switch will blink faster, and then the direct
monitor soft control switch (SOFT CTRL) will light.
(The operation will be cancelled if you press any LED switch other than the STEREO/MONO select switch.)
Once the direct monitor soft control switch (SOFT CTRL) has lighted, the output volume select switch and
the STEREO/MONO select switch will go out.
The factory settings have now been restored.
Factory settings
Function
STEREO/MONO select switch
Direct monitor soft control switch
ADAT
EXT CLOCK
Output volume mode
State
STEREO
On
Off
Off
MAIN
* For details of the UA-1000's internal block structure when it is shipped from the factory, refer to “Block
diagram” (p. 51).
44
UA-1000_e.book 45 ページ 2003年8月6日 水曜日 午前11時52分
Troubleshooting
If an unexpected problem occurs while using the UA-1000, read this chapter first. It contains numerous tips for
resolving problems.
If you are using Windows for the first time, and as a result find it difficult to follow the procedural explanations,
please refer to the manuals that came with your computer or operating system.
Be sure to read the README_E.HTM file in the Driver -> USB_XP folder of the CD-ROM. The file contain any
additional information that was not included in this manual.
Problems related to the USB driver
An “Unknown driver found” dialog box appears, and you are unable to
install the driver
“Find new hardware wizard” ends before the process is completed
● It may take about 15 seconds (or more) after the USB cable is connected for the UA-1000 to be
detected.
● Is the USB cable connected correctly?
Make sure that the UA-1000 and your computer are correctly connected via a USB cable.
● Is USB enabled on your computer?
Refer to the operation manual for your computer, and make sure that USB is enabled.
● Does your computer meet the USB specifications?
If you are using a computer that does not fulfill the electrical requirements of the USB specifications, operation
may be unstable. In this case, you may be able to solve the problem by connecting a USB hub.
Cannot install the driver correctly
Using the procedure for “Deleting the driver” (p. 45), delete the USB audio device driver installed in your
computer, and then re-install the UA-1000 driver as described in “Installing the driver” (p. 18).
Can’t install/delete/use the driver
● Did you log on to Windows as a user with administrative privileges?
In order to install/delete/re-install the driver in Windows XP, you must be logged into Windows as a user with
administrative privileges, such as Administrator. For details, please contact the system administrator for your
computer system.
● Did you make “Driver Signing Options?”
In order to install/re-install the driver, you must make “Driver Signing Options” ( p. 18).
Windows XP displays a “Hardware Installation” dialog box
● Did you make “Driver Signing Options?”
In order to install/re-install the driver, you must make “Driver Signing Options” ( p. 18).
Deleting the driver
If you were unable to install the driver according to the procedure given, the UA-1000 may not be recognized
correctly by the computer. In this case, use the following procedure to delete the driver, and then follow the
procedure in “Installing the driver” (p. 18) to install the driver once again.
1. With the UA-1000 disconnected, start up Windows.
Disconnect all USB cables except for a USB keyboard and USB mouse (if used).
2. Insert the CD-ROM into the CD-ROM drive of your computer.
3. Click the Windows start button. From the menu that appears, select “Run...”
In the “Run...” dialog box, input the following into the “Open” field, and click [OK].
*
D:\DRIVER\USB_XP\Uninstal.EXE
The drive name “D:” may be different for your system. Specify the drive name of your CD-ROM drive.
4. Perform the installation as directed by the dialog boxes that appear.
45
UA-1000_e.book 46 ページ 2003年8月6日 水曜日 午前11時52分
Troubleshooting
Problems related to the UA-1000
Can’t output/input sound
● Is the UA-1000’s external clock switch set correctly?
If the UA-1000’s external clock switch is blinking, the UA-1000 is not synchronized with the word clock from the
external device or with the clock of the digital signal being input to the optical digital input connector.
For details, refer to “External clock switch” (p. 43).
● In UA-1000 Control Panel, could MONITOR be turned OFF?
If MONITOR is turned OFF in the control panel, the audio output will be muted. Turn MONITOR ON in the UA1000 Control Panel.
For details on Control Panel, refer to “UA-1000 Control Panel” (p. 36).
● Are the input/output settings of your software correct?
Check the audio input/output settings of the software you are using.
(-> “Driver settings” (p. 23))
Can’t hear sound from the computer
● Is it possible that the UA-1000’s Master volume has been placed at 0 (turned fully
counterclockwise)?
● Have you specified the audio and MIDI data output destination for your operating system?
You must specify the UA-1000 as the audio data output destination for your computer.For details on how to make
this setting, refer to Settings and checking.
(-> “Driver settings” (p. 23))
● Are you running multiple applications?
If multiple applications are running simultaneously, an error message may appear. If this occurs, click [OK] and
exit the other applications.
Even if an application window is closed, it is still running if it appears in the taskbar. Be sure to exit unneeded
applications displayed.
● Was the driver installed correctly?
In order for you to play back audio data via the UA-1000, the driver must be installed. For installation and
settings, refer to “Installing the driver” (p. 18).
● Is your computer in Suspend or Sleep mode?
If so, get your computer to resume normal operation, then exit all applications that are using the UA-1000. Next,
turn the UA-1000’s power off, then switch it on again.
● Did you plug-in or unplug the USB cable or turn the power of the UA-1000 off/on while an
application was running?
Exit all applications that are using the UA-1000, and exit all applications that are using the UA-1000, and reconnect the UA-1000.
● Are the faders of the Windows volume control raised?
Make settings so that Windows will give priority to background services, to ensure that audio and MIDI data are
processed smoothly. Adjust the volume of the faders in the Windows volume control. Also make sure that the
relevant fader is not muted.
To open the volume control, click the Windows start button and choose All Programs -> Accessories ->
Entertainment -> Volume Control.
46
UA-1000_e.book 47 ページ 2003年8月6日 水曜日 午前11時52分
Troubleshooting
Sound from devices connected to the input jack is not heard in the headphones
● Is the headphone volume set appropriately?
Turn the knob clockwise to adjust the volume.
● Is the rear panel insertion/input jack select switch set appropriately?
Refer to “Insertion / Input jack select switches” (p. 16), and set the switch appropriately.
● If you are using digital input, turn the External clock switch on.
Volume from a device connected to the input jacks is too low
● Are you using a cable that has a built-in resistor?
Use a cable without a built-in resistor (e.g., Roland PCS series).
● Is the Input volume raised appropriately?
Turn the knob clockwise to adjust the volume.
The sound of a device connected to the input jack is distorted
If you are inputting sound through the input jacks, use the Input sensitivity knobs of the UA-1000 to lower the
input level.
Noise is heard during audio playback
● Is a mic or guitar still connected?
If a mic or guitar is connected to the UA-1000, disconnect the mic or guitar, and turn the input sensitivity knob all
the way to the left. Disconnect any audio devices you are not using.
● Noise is sometimes heard in the line input or mic input.
If a USB-compatible MIDI sound module and the UA-1000 are connected via USB to the same computer, and the
outputs of the MIDI sound module are connected to the line input jacks of the UA-1000, noise from your computer
may be heard via the MIDI sound module from the UA-1000, depending on the computer you are using. If this
occurs, you can either connect the MIDI sound module and the UA-1000 in parallel using a self-powered hub, or
connect the MIDI sound module via its serial or MIDI interface.
● Are two or more audio devices such as the UA-1000 or a mixer connected to your computer?
Try connecting only a single UA-1000 unit, and check whether the noise disappears. If numerous audio devices
are connected to a computer, noise may occur depending on your system. In such cases, connect only the UA1000 to your computer.
● In some cases, you may also be able to solve this problem by grounding the chassis of your
computer, or the grounding connector of the AC power supply plug of your computer. In
addition, you can check whether any devices that produce a strong magnetic field are located
nearby, such as a television or microwave oven.
● Also check the troubleshooting item Sound is interrupted during audio playback (p. 48).
47
UA-1000_e.book 48 ページ 2003年8月6日 水曜日 午前11時52分
Troubleshooting
Sound is interrupted during audio playback
● If Cubase SX displays a message of “Sample could not be set,” open “Project Setup” and click
the [OK] button in order to solve the problem.
● The sound may be interrupted if a LAN is operating.
Try disabling the LAN in the Device Manager. If this solved the problem of sound being interrupted, you may be
able to solve the problem of interrupted sound by updating the driver or BIOS.
● Are many applications running on your computer?
If you use many applications or start up other applications during playback, playback may be interrupted,
depending on your computer system. Please exit unneeded applications, and try again. If this does not resolve
the problem, try restarting your computer.
● Try installing more memory.
Installing more memory will increase the performance of your computer. For details on how to install more
memory, refer to the operation manual for your computer.
● Does your computer satisfy the requirements of the USB2.0 standard?
If you are using a computer (such as a computer that you yourself assembled) that does not satisfy the electrical
requirements of the USB2.0 specifications, you may experience interruptions in the audio. If this occurs, you may
be able to solve the problem by connecting a USB hub that contains its own power supply.
● Giving priority to background services
To ensure that audio MIDI and processing occurs smoothly, use the following procedure to make settings.
(-> “Giving priority to background services” (p. 22))
● You can solve this problem in the “Driver Settings” dialog box.
For details, refer to the section “Part of the playback is wrong: e.g., notes are broken off prematurely, or some
notes are lost” within the README_E.HTM file located in the folder in which you installed the CD-ROM.
Digitally recorded sound is distorted, is at the wrong pitch, or contains noise
If you are using a long optical digital cable, noise may be produced when the cable is connected, or the sound may
be distorted. We recommend that you use optical digital cables that are no longer than one meter in length.
● Does the sampling frequency setting of your application match the setting of the UA-1000’s
sampling frequency switch?
Set this to the sampling frequency that is selected in your recording software.
Playback or recording halts midway through, and then becomes impossible
● Was a heavy processing load experienced while using the UA-1000, such as accessing the CDROM drive or a network?
If an operation involving a heavy processing load is performed while the UA-1000 is in use, it may not operate
correctly. If this occurs, stop playback/recording, and then try resuming playback/recording. If you are still unable
to play back/record, exit all applications that use the UA-1000, switch off the UA-1000, then turn it on again.m
Recording produces a silent (blank) file
● Have you correctly specified the audio data that is to be input in the operating system?
Make the correct settings as described in “Driver settings” (p. 23).
● On your recording software, is the audio data input destination set correctly?
Make the correct settings as described in “Driver settings” (p. 23).
Noise is present in the sound
● If you are using word clock, noise may be caused by jitter occurring in the master device.
If you are using word clock with another digital device as the master and the UA-1000 as the slave, jitter occurring
in the master device may cause noise.
48
UA-1000_e.book 49 ページ 2003年8月6日 水曜日 午前11時52分
Troubleshooting
Can’t record/play MIDI
● Is the MIDI device you are using set correctly?
In order to record/play MIDI tracks via the UA-1000, the UA-1000 driver must be installed correctly. (->
“Installing the driver” (p. 18))
● Are the track outputs set correctly?
You cannot hear MIDI tracks that are not assigned to a MIDI playback device. If you want to play back a MIDI
track, make sure that the MIDI device you are using is shown as the MIDI output port in your software. For
details, refer to the owner’s manual of the software you are using.
● Notes are interrupted or lag during MIDI playback
Make settings so that Windows gives priority to background services.
Make settings as described in “Giving priority to background services” (p. 22).
Can’t specify the audio input/output destination in Cubase
● By performing the following procedure, you will be able to use five streams of audio in Cubase.
1. From the Panels menu, choose VST Inputs.
2. Click the buttons marked In 1/2–In 9/10 and Mon L/R so they are lit.
3. Close the VST Inputs window.
4. From the Panels menu, choose VST Master Mixer.
5. Drag the bottom right of the window toward the right to make the window wider.
6. Click the [Active] buttons so they are all lit.
7. Click the buttons located below the sliders to successively select Out 3–Out 9.
8. Close the VST Master Mixer window.
9. In the Arrangements window, click the Out field and select either Master, BUS 2, BUS 3, BUS 4, or BUS 5.
*
If you want to use stereo output, select a track and then click the [Stereo] button located in Track Info.
Cubase SX
1. From the Device menu, choose VST Inputs.
2. Click the Active buttons for In 1/2–In 9/10 and Mon L/R so they are all lit.
3. Close the VST Inputs window.
4. From the Device menu, choose VST Outputs.
5. Drag the bottom right of the window toward the right to make the window wider.
6. Click the [Active] buttons so they are all lit.
7. Click the buttons located below the sliders to successively select Out 3–Out 9.
8. Close the VST Options window.
9. In the Arrangements window, click the Out field and select either BUS 1, BUS 2, BUS 3, BUS 4, or BUS 5.
49
UA-1000_e.book 50 ページ 2003年8月6日 水曜日 午前11時52分
Main specifications
UA-1000: USB 2.0 Audio Capture
Number of Audio Record/Playback Channels
Record: 10 channels
Playback: 10 channels
Full duplex
Signal Processing
PC interface: 24 bits
AD/DA Conversion: 24 bits
Internal Processing:40 bits
Connectors
<Front Panel>
Input Jack 1–4 (XLR type / 1/4 inch TRS phone type)
XLR type (balanced / phantom power)
1/4 inch TRS phone type (balanced)
* Input Jack 3 supports Guitar Hi-Z.
Headphones Jack (Stereo 1/4 inch phone type)
<Rear Panel>
Insert/Input Jack 1–4
Sampling Frequency
Digital output:
44.1/48/88.2/96 kHz
Digital input:
44.1/48/88.2/96 kHz
AD/DA Conversion: 44.1/48/88.2/96 kHz
Frequency Response
96.0 kHz:
88.2 kHz:
48.0 kHz:
44.1 kHz:
20 Hz to 40 kHz (+0 dB/-2 dB)
20 Hz to 40 kHz (+0 dB/-2 dB)
20 Hz to 22 kHz (+0 dB/-2 dB)
20 Hz to 20 kHz (+0 dB/-2 dB)
Nominal Input Level (variable)
Input Jack 1–4 (Front)
-60 to -16 dBu (PAD OFF)
-40 to +4 dBu (PAD ON)
Insert/Input Jack 1–4 (Rear)
+4 dBu
Input Jack 5–8 (Rear)
-20 to +4 dBu
Nominal Output Level
Output Jack 1–8
+4 dBu (balanced)
Residual Noise Level
(input terminated with 1 k ohms,
MAIN VOLUME: 0 dB, INPUT SENS: +4 dBu,
DIRECT MONITOR VOLUME: 0 dB, IHF-A typ.)
Output Jack 1-2
-89 dBu
Interface
(1/4 inch phone type, Insert:TRS, Input:unbalanced)
Input Jack 5–8 (1/4 inch TRS phone type (balanced))
Output Jack 1–8 (1/4 inch TRS phone type (balanced))
Digital In Connectors (Coaxial type, Optical type)
Digital Out Connectors (Coaxial type, Optical type)
MIDI Connectors (In, Out)
Word Clock Connectors (In, Out) (BNC type)
USB Connector
Power Supply
AC 117 V, AC 230 V, AC 240 V: 50/60Hz
AC 220 V: 60Hz
Power Consumption
25 W
Dimensions
431 (W) x 244 (D) x 44 (H) mm
17 (W) x 9-5/8 (D) x 1-3/4 (H) inches
Weight
2.8 kg / 6 lbs 3 oz
Accessories
Owner’s Manual
CD-ROM
Power cord
USB cable
Rackmount adaptor
Ferrite core (for 230V and 240V)
(0 dBu = 0.775 V rms)
USB 2.0
Digital input/output (conforms to IEC60958)
Coaxial type
Optical type
conforms to IEC60958 and ADAT
ADAT capability:
48 kHz: 50.8 kHz - 40.4 kHz
44.1 khz: 49.5 kHz - 40.4 kHz
MIDI IN/OUT
*In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.
50
UA-1000_e.book 51 ページ 2003年8月6日 水曜日 午前11時52分
Block diagram
■Factory settings
INPUT MONITOR
(DIRECT MONITOR)
SOFT CTRL
OFF(BYPASS)
WAVE OUT
MONITOR
51
UA-1000_e.book 52 ページ 2003年8月6日 水曜日 午前11時52分
Block diagram
■Output volume select switch: MAIN
INPUT MONITOR
(DIRECT MONITOR)
SOFT CTRL
ON / OFF(BYPASS)
WAVE OUT
MONITOR
■Output volume select switch: ALL
INPUT MONITOR
(DIRECT MONITOR)
SOFT CTRL
ON / OFF(BYPASS)
52
WAVE OUT
MONITOR
UA-1000_e.book 53 ページ 2003年8月6日 水曜日 午前11時52分
INDEX
Numerics
I
192 kHz ........................................................................... 38
5.1 channel ...................................................................... 31
Input impedance select switch .............................. 12, 27
Input jack mode ............................................................. 16
Input jacks ...................................................................... 15
INPUT MONITOR .................................................. 38–39
Input peak indicators .................................................... 12
Input sensitivity knob ................................................... 28
Input sensitivity knobs ................................................. 11
Insertion / Input jack select switches ......................... 16
Insertion / Input jacks .................................................. 16
Insertion jack mode ....................................................... 16
Insertion/Input jack select switch .............................. 32
Internal blocks ............................................................... 36
A
AC inlet ........................................................................... 15
ADAT ........................................................................ 29–30
ADAT mode switch ................................................ 12, 29
ADAT mode switch and external clock switch ........ 30
ASIO ................................................................................ 23
ASIO audio device ........................................................ 23
ASIO Direct Monitor ..................................................... 40
Audio device .................................................................. 23
Audio input device ....................................................... 23
Audio output device ..................................................... 23
B
background service ....................................................... 22
C
Coaxial digital input jack ............................................. 15
Coaxial digital output jack ........................................... 15
Combo input jacks ........................................................ 11
D
Device Panel ................................................................... 38
DIRECT MONITOR ...................................................... 39
Direct monitor section .................................................. 13
Direct monitor soft control switch .................. 13, 27, 33
Direct monitor volume ..................................... 13, 27, 33
driver ............................................................................... 18
Driver Signing ................................................................ 18
E
EDIROL UA-1000 .......................................................... 23
effects .............................................................................. 32
External clock switch ........................................ 12, 33–34
F
Ferrite Core .................................................................... 10
Front panel ..................................................................... 11
G
Gain select switches ...................................................... 11
guitar ............................................................................... 27
H
Headphone jack ............................................................. 14
L
latency ............................................................................. 40
M
memories ........................................................................
mic ...................................................................................
MIDI device ....................................................................
MIDI IN device ..............................................................
MIDI IN/OUT connectors ...........................................
MIDI OUT device ..........................................................
MME ................................................................................
MME EDIROL UA-1000 ...............................................
MONITOR OUT ............................................................
39
27
23
23
15
23
23
23
26
O
optical digital input jack ............................................... 15
optical digital output jack ............................................ 15
Output indicators .......................................................... 12
Output jacks ................................................................... 16
Output level indicators ................................................. 14
OUTPUT PATCH BAY ..................................... 26, 38–39
Output volume knob .............................................. 14, 31
Output volume select switch ........................... 14, 28, 31
P
PAD ................................................................................. 11
PATCH BAY .................................................................. 31
Phantom power switch ................................................. 27
Phantom power switches ............................................. 11
Power cord ....................................................................... 9
Power indicator ............................................................. 14
Power switch .................................................................. 14
53
UA-1000_e.book 54 ページ 2003年8月6日 水曜日 午前11時52分
INDEX
R
Rackmount adaptors ..................................................... 10
Rear panel ....................................................................... 15
S
Sampling frequency select switch . 13, 27, 29–30, 33–34
STEREO/MONO select switch ............................. 13, 27
System ............................................................................. 18
U
UA-1000 Control Panel ................................................. 36
UA-1000 internal patching ........................................... 31
USB cable .......................................................................... 9
USB connector ................................................................ 15
USER SET ................................................................. 13, 38
W
WAVE IN PATCH BAY ...............................................
WAVE OUT MONITOR ...............................................
WDM ...............................................................................
WORD CLOCK IN/OUT jacks ...................................
54
38
38
23
15
UA-1000_e.book 55 ページ 2003年8月6日 水曜日 午前11時52分
For EU Countries
This product complies with the requirements of European Directives EMC 89/336/EEC and LVD 73/23/EEC.
For the USA
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class B Limit.
For Canada
NOTICE
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
AVIS
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
For the USA
DECLARATION OF CONFORMITY
Compliance Information Statement
Model Name :
Type of Equipment :
Responsible Party :
Address :
Telephone :
UA-1000
USB2.0 Audio Interface
Edirol Corporation North America
425 Sequoia Drive, Suite 114, Bellingham, WA 98226
(360) 594-4276
Information
EUROPE
EDIROL (Europe) Ltd.
Studio 3.4 114 Power Road
London W4 5PY
U. K.
TEL: +44 (0)20 8747 5949
FAX:+44 (0)20 8747 5948
http://www.edirol.com/europe
Deutschland
TEL: 0700 33 47 65 20
France
TEL: 0810 000 371
Italia
TEL: 02 93778329
When you need repair service, call your nearest EDIROL/Roland Service Center or authorized
EDIROL/Roland distributor in your country as shown below.
HONG KONG
BARBADOS
PERU
IRELAND
CYPRUS
Parsons Music Ltd.
8th Floor, Railway Plaza, 39
Chatham Road South, T.S.T,
Kowloon, HONG KONG
TEL: 2333 1863
A&B Music Supplies LTD
12 Webster Industrial Park
Wildey, St.Michael, Barbados
TEL: (246)430-1100
Audionet
Distribuciones Musicales SAC
Juan Fanning 530
Miraflores
Lima - Peru
TEL: (511) 4461388
Roland Ireland
G2 Calmount Park, Calmount
Avenue, Dublin 12
Republic of IRELAND
TEL: (01) 4294444
Radex Sound Equipment Ltd.
17, Diagorou Street, Nicosia,
CYPRUS
TEL: (022) 66-9426
INDIA
Rivera Digitec (India) Pvt. Ltd.
409, Nirman Kendra
Mahalaxmi Flats Compound
Off. Dr. Edwin Moses Road,
Mumbai-400011, INDIA
TEL: (022) 2493 9051
INDONESIA
PT Citra IntiRama
J1. Cideng Timur No. 15J-150
Jakarta Pusat
INDONESIA
TEL: (021) 6324170
KOREA
NORTH AMERICA
CANADA
Roland Canada Music Ltd.
(Head Office)
5480 Parkwood Way Richmond
B. C., V6V 2M4 CANADA
TEL: (604) 270 6626
Roland Canada Music Ltd.
(Toronto Office)
170 Admiral Boulevard
Mississauga On L5T 2N6
CANADA
TEL: (905) 362 9707
U. S. A.
Roland Corporation U.S.
5100 S. Eastern Avenue
Los Angeles, CA 90040-2938,
U. S. A.
TEL: (323) 890 3700
AFRICA
Cosmos Corporation
1461-9, Seocho-Dong,
Seocho Ku, Seoul, KOREA
TEL: (02) 3486-8855
MALAYSIA/
SINGAPORE
Roland Asia Pacific Sdn. Bhd.
45-1, Block C2, Jalan PJU 1/39,
Dataran Prima, 47301 Petaling
Jaya, Selangor, MALAYSIA
TEL: (03) 7805-3263
PHILIPPINES
G.A. Yupangco & Co. Inc.
339 Gil J. Puyat Avenue
Makati, Metro Manila 1200,
PHILIPPINES
TEL: (02) 899 9801
TAIWAN
ROLAND TAIWAN
ENTERPRISE CO., LTD.
Room 5, 9fl. No. 112 Chung
Shan N.Road Sec.2, Taipei,
TAIWAN, R.O.C.
TEL: (02) 2561 3339
EGYPT
THAILAND
Al Fanny Trading Office
9, EBN Hagar A1 Askalany
Street,
ARD E1 Golf, Heliopolis,
Cairo 11341, EGYPT
TEL: 20-2-417-1828
Theera Music Co. , Ltd.
330 Soi Verng NakornKasem,
New Road, Sumpantawongse,
Bangkok 10100, THAILAND
TEL: (02) 224-8821
REUNION
Maison FO - YAM Marcel
25 Rue Jules Hermann,
Chaudron - BP79 97 491
Ste Clotilde Cedex,
REUNION ISLAND
TEL: (0262) 218-429
SOUTH AFRICA
Paul Bothner(PTY)Ltd.
Royal Cape Park, Unit 24
Londonderry Road, Ottery 7800
Cape Town, SOUTH AFRICA
TEL: (021) 799 4900
ASIA
CHINA
Roland Shanghai Electronics
Co.,Ltd.
5F. No.1500 Pingliang Road
Shanghai 200090, CHINA
TEL: (021) 5580-0800
Roland Shanghai Electronics
Co.,Ltd.
(BEIJING OFFICE)
10F. No.18 3 Section Anhuaxili
Chaoyang District Beijing
100011 CHINA
TEL: (010) 6426-5050
Roland Shanghai Electronics
Co.,Ltd.
(GUANGZHOU OFFICE)
2/F., No.30 Si You Nan Er Jie
Yi Xiang, Wu Yang Xin Cheng,
Guangzhou 510600, CHINA
TEL: (020) 8736-0428
VIETNAM
SAIGON MUSIC
DISTRIBUTOR
(TAN DINH MUSIC)
138 Tran Quang Khai Street
Dist. 1, Ho Chi Minh City
VIETNAM
TEL: (08) 848-4068
AUSTRALIA/
NEW ZEALAND
AUSTRALIA/
NEW ZEALAND
Roland Corporation
Australia Pty.,Ltd.
38 Campbell Avenue
Dee Why West. NSW 2099
AUSTRALIA
For Australia
Tel: (02) 9982 8266
For New Zealand
Tel: (09) 3098 715
CENTRAL/LATIN
AMERICA
ARGENTINA
Instrumentos Musicales S.A.
Av.Santa Fe 2055
(1123) Buenos Aires
ARGENTINA
TEL: (011) 4508-2700
BRAZIL
Roland Brasil Ltda.
Rua San Jose, 780 Sala B
Parque Industrial San Jose
Cotia - Sao Paulo - SP, BRAZIL
TEL: (011) 4615 5666
CHILE
Comercial Fancy II S.A.
Rut.: 96.919.420-1
Nataniel Cox #739, 4th Floor
Santiago - Centro, CHILE
TEL: (02) 688-9540
COLOMBIA
Centro Musical Ltda.
Cra 43 B No 25 A 41 Bododega 9
Medellin, Colombia
TEL: (574)3812529
CURACAO
Zeelandia Music Center Inc.
Orionweg 30
Curacao, Netherland Antilles
TEL:(305)5926866
TRINIDAD
AMR Ltd
Ground Floor
Maritime Plaza
Barataria Trinidad W.I.
TEL: (868)638 6385
URUGUAY
Todo Musica S.A.
Francisco Acuna de Figueroa 1771
C.P.: 11.800
Montevideo, URUGUAY
TEL: (02) 924-2335
VENEZUELA
Instrumentos Musicales
Allegro,C.A.
Av.las industrias edf.Guitar
import
#7 zona Industrial de Turumo
Caracas, Venezuela
TEL: (212) 244-1122
DOMINICAN REPUBLIC
Instrumentos Fernando Giraldez
Calle Proyecto Central No.3
Ens.La Esperilla
Santo Domingo,
Dominican Republic
TEL:(809) 683 0305
ECUADOR
Mas Musika
Rumichaca 822 y Zaruma
Guayaquil - Ecuador
TEL:(593-4)2302364
EUROPE
AUSTRIA
Roland Elektronische
Musikinstrumente HmbH.
Austrian Office
Eduard-Bodem-Gasse 8,
A-6020 Innsbruck, AUSTRIA
TEL: (0512) 26 44 260
ITALY
Roland Italy S. p. A.
Viale delle Industrie 8,
20020 Arese, Milano, ITALY
TEL: (02) 937-78300
MOCO INC.
No.41 Nike St., Dr.Shariyati Ave.,
Roberoye Cerahe Mirdamad
Tehran, IRAN
TEL: (021) 285-4169
NORWAY
ISRAEL
Roland Scandinavia Avd.
Kontor Norge
Lilleakerveien 2 Postboks 95
Lilleaker N-0216 Oslo
NORWAY
TEL: 2273 0074
Halilit P. Greenspoon & Sons
Ltd.
8 Retzif Ha’aliya Hashnya St.
Tel-Aviv-Yafo ISRAEL
TEL: (03) 6823666
POLAND
MX MUSIC SP.Z.O.O.
UL. Gibraltarska 4.
PL-03664 Warszawa POLAND
TEL: (022) 679 44 19
MUSIC HOUSE CO. LTD.
FREDDY FOR MUSIC
P. O. Box 922846
Amman 11192 JORDAN
TEL: (06) 5692696
PORTUGAL
KUWAIT
Roland Iberia, S.L.
Portugal Office
Cais das Pedras, 8/9-1 Dto
4050-465, Porto, PORTUGAL
TEL: 22 608 00 60
EASA HUSAIN AL-YOUSIFI
& SONS CO.
Abdullah Salem Street,
Safat, KUWAIT
TEL: 243-6399
ROMANIA
LEBANON
FBS LINES
Piata Libertatii 1,
535500 Gheorgheni,
ROMANIA
TEL: (266) 364 609
Chahine S.A.L.
Gerge Zeidan St., Chahine
Bldg., Achrafieh, P.O.Box: 165857
Beirut, LEBANON
TEL: (01) 20-1441
RUSSIA
MuTek
Dorozhnaya ul.3,korp.6
117 545 Moscow, RUSSIA
TEL: (095) 981-4967
BELGIUM/FRANCE/
HOLLAND/
LUXEMBOURG
SPAIN
Roland Central Europe N.V.
Houtstraat 3, B-2260, Oevel
(Westerlo) BELGIUM
TEL: (014) 575811
Roland Iberia, S.L.
Paseo García Faria, 33-35
08005 Barcelona SPAIN
TEL: 93 493 91 00
HONDURAS
CZECH REP.
SWEDEN
Almacen Pajaro Azul S.A. de C.V.
BO.Paz Barahona
3 Ave.11 Calle S.O
San Pedro Sula, Honduras
TEL: (504) 553-2029
K-AUDIO
Kardasovska 626.
CZ-198 00 Praha 9,
CZECH REP.
TEL: (2) 666 10529
Roland Scandinavia A/S
SWEDISH SALES OFFICE
Danvik Center 28, 2 tr.
S-131 30 Nacka SWEDEN
TEL: (0)8 702 00 20
MARTINIQUE
DENMARK
SWITZERLAND
Musique & Son
Z.I.Les Mangle
97232 Le Lamantin
Martinique F.W.I.
TEL: 596 596 426860
Roland Scandinavia A/S
Nordhavnsvej 7, Postbox 880,
DK-2100 Copenhagen
DENMARK
TEL: 3916 6200
Roland (Switzerland) AG
Landstrasse 5, Postfach,
CH-4452 Itingen,
SWITZERLAND
TEL: (061) 927-8383
FINLAND
UKRAINE
Roland Scandinavia As, Filial
Finland
Elannontie 5
FIN-01510 Vantaa, FINLAND
TEL: (0)9 68 24 020
TIC-TAC
Mira Str. 19/108
P.O. Box 180
295400 Munkachevo,
UKRAINE
TEL: (03131) 414-40
GUATEMALA
Casa Instrumental
Calzada Roosevelt 34-01,zona 11
Ciudad de Guatemala
Guatemala
TEL:(502) 599-2888
Gigamusic SARL
10 Rte De La Folie
97200 Fort De France
Martinique F.W.I.
TEL: 596 596 715222
MEXICO
Casa Veerkamp, s.a. de c.v.
Av. Toluca No. 323, Col. Olivar
de los Padres 01780 Mexico
D.F. MEXICO
TEL: (55) 5668-6699
NICARAGUA
Bansbach Instrumentos
Musicales Nicaragua
Altamira D'Este Calle Principal
de la Farmacia 5ta.Avenida
1 Cuadra al Lago.#503
Managua, Nicaragua
TEL: (505)277-2557
GERMANY
Roland Elektronische
Musikinstrumente HmbH.
Oststrasse 96, 22844
Norderstedt, GERMANY
TEL: (040) 52 60090
GREECE
STOLLAS S.A.
Music Sound Light
155, New National Road
Patras 26442, GREECE
TEL: 2610 435400
HUNGARY
Roland East Europe Ltd.
Warehouse Area ‘DEPO’ Pf.83
H-2046 Torokbalint,
HUNGARY
IRAN
JORDAN
OMAN
TALENTZ CENTRE L.L.C.
Malatan House No.1
Al Noor Street, Ruwi
SULTANATE OF OMAN
TEL: 2478 3443
QATAR
Badie Studio & Stores
P.O. Box 62,
Doha, QATAR
TEL: 423554
SAUDI ARABIA
aDawliah Universal
Electronics APL
Corniche Road, Aldossary
Bldg., 1st Floor, Alkhobar,
SAUDI ARABIA
P.O.Box 2154, Alkhobar 31952
SAUDI ARABIA
TEL: (03) 898 2081
SYRIA
Technical Light & Sound
Center
Rawda, Abdul Qader Jazairi St.
Bldg. No. 21, P.O.BOX 13520,
Damascus, SYRIA
TEL: (011) 223-5384
TURKEY
UNITED KINGDOM
Roland (U.K.) Ltd.
Atlantic Close, Swansea
Enterprise Park, SWANSEA
SA7 9FJ,
UNITED KINGDOM
TEL: (01792) 702701
MIDDLE EAST
ZUHAL DIS TICARET A.S.
Galip Dede Cad. No.37
Beyoglu - Istanbul / TURKEY
TEL: (0212) 249 85 10
U.A.E.
Zak Electronics & Musical
Instruments Co. L.L.C.
Zabeel Road, Al Sherooq Bldg.,
No. 14, Grand Floor, Dubai,
U.A.E.
TEL: (04) 3360715
BAHRAIN
Moon Stores
No.16, Bab Al Bahrain Avenue,
P.O.Box 247, Manama 304,
State of BAHRAIN
TEL: 17 211 005
TEL: (23) 511011
As of December 10, 2005 (EDIROL-1)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement