04_RSX_CigLighter
INSTALLATION
INSTRUCTIONS
Accessory
Application
CIGARETTE LIGHTER
P/N 08U96-S6M-200
2004 RSX
PARTS LIST
Publications No.
BII 26194
Issue Date
SEP 2003
3.
Cigarette lighter
Turn the two knobs counterclockwise, and
remove the driver’s dashboard lower cover by
pulling it toward you (two retaining tabs and two
hooks).
Cigarette lighter harness
HOOKS (2)
RETAINING
TABS (2)
3 Wire ties
DRIVER’S
DASHBOARD
LOWER
COVER
KNOB
TOOLS REQUIRED
Flat-tip screwdriver
10 mm Combination wrench
Diagonal cutters
4.
Turn the knob clockwise and remove the driver’s
dashboard under cover from the holder by pulling
it toward you (one clip).
INSTALLATION
Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your vehicle. These procedures should
not be attempted by “do-it-yourselfers.”
1.
Make sure you have the anti-theft code for the
radio, then write down the radio station presets. .
2.
Disconnect the negative cable from the battery.
HOLDER
KNOB
DRIVER’S
DASHBOARD
UNDER
COVER
CLIP
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
BII 26194 (0309)
08U96-S6M-2001-91
1 of 5
5.
Pull the center lower cover toward you to release
the one retaining tab and six clips.
9.
Open the lid, and remove the accessory socket
from the center lower cover by releasing the two
retaining tabs.
LID
RETAINING TAB
CLIPS (6)
VEHICLE 2-PIN
CONNECTOR
CENTER LOWER
COVER
ACCESSORY
SOCKET
6.
Unplug the vehicle 2-pin connector from the
accessory socket, and remove the center lower
cover.
7.
Secure the 2-pin connector (black) of the
cigarette lighter harness to the cigarette lighter
harness with one wire tie.
12-PIN
CONNECTOR
ACCESSORY
SOCKET
RETAINING
TAB
CENTER LOWER
COVER
10. Remove the accessory socket protector from the
center lower cover by releasing the two retaining
tabs.
CIGARETTE LIGHTER HARNESS
ACCESSORY SOCKET
PROTECTOR
GROUND
TERMINAL WIRE
2-PIN
CONNECTOR
(black)
GROUND
TERMINAL
WIRE
WIRE
TIE
12-PIN
CONNECTOR
8.
2 of 5
WIRE TIE
Connect the 12-pin male and female connectors
of the cigarette harness, then secure those
12-pin connectors and ground terminal wire to the
cigarette lighter harness with one wire tie.
BII 26194 (0309)
CENTER LOWER
COVER
RETAINING
TABS (2)
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
11. Slide the ring into the hole in the center lower
cover in the direction shown.
13. Remove the bolt that secures the fuse box, and
lower the fuse box.
CENTER LOWER COVER
14. Unplug the vehicle 6-pin connector from the fuse
box, and plug the 6-pin connector of the cigarette
lighter harness there.
NOTE: On M/T vehicles, there is no 6-pin
connector plugged into the fuse box.
CIGARETTE
LIGHTER
HARNESS
VEHICLE
6-PIN CONNECTOR
(A/T vehicles only)
CIGARETTE
LIGHTER
HARNESS
6-PIN
CONNECTOR
RING
12. Align the locating tab of the socket with the cutout
in the ring, and slide the socket of the cigarette
lighter into the ring.
FUSE
BOX
BOLT
CENTER LOWER COVER
DUMMY
CONNECTOR
(Discard.)
6-PIN CONNECTOR
FUSE BOX
RING
CUTOUT
SOCKET
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
LOCATING
TAB
15. On A/T vehicles, locate the 6-pin connector taped
to the cigarette lighter harness, and remove the
dummy connector. Plug the vehicle 6-pin
connector you just unplugged from the fuse box
into that connector.
BII 26194 (0309)
3 of 5
16. If the vehicle is equipped with optional fog lights,
plug the fog light harness 6-pin connector into the
cigarette lighter harness.
FUSE BOX
6-PIN CONNECTOR
19. Route the 2-pin connector of the cigarette lighter
harness to the center lower cover opening.
20. Connect the 2-pin connectors of the cigarette
lighter harness and the vehicle harness to the
cigarette lighter.
CIGARETTE
LIGHTER
HARNESS
FOG LIGHT
HARNESS
CENTER LOWER
COVER OPENING
CIGARETTE
LIGHTER
HARNESS 2-PIN
CONNECTOR
CENTER LOWER
COVER
CIGARETTE
LIGHTER
HARNESS
17. Reinstall the fuse box.
18. Route the cigarette lighter harness above the
steering shaft, then secure the cigarette lighter
harness to the vehicle harness with one wire tie in
the area shown.
CIGARETTE
LIGHTER HARNESS
VEHICLE
HARNESS
2-PIN
CONNECTOR
CIGARETTE
LIGHTER
SOCKET
CIGARETTE
LIGHTER
21. Reinstall the center lower cover, and push the
cigarette lighter into the socket.
22. Check that all wire harnesses are routed properly
and all connectors are plugged in.
STEERING
SHAFT
23. Reconnect the negative cable to the battery.
24. Reset the clock and the radio station presets.
25. Reinstall all removed parts. Make sure that all
retaining clips and tabs are securely fastened.
WIRE TIE
VEHICLE
HARNESS
WIRE TIE
VEHICLE
HARNESS
CIGARETTE
LIGHTER HARNESS
NOTE: Whenever the battery is disconnected, the
driver’s window AUTO function is disabled.
26. Start the engine. Push down on the driver’s
window switch until the window is fully open.
27. Pull up on the driver’s window switch to close the
window completely, then hold the switch for
2 seconds.
28. Test the window AUTO function.
29. Do the ECM/PCM idle learn procedure.
•
Make sure all electrical items are turned off.
•
Start the engine. Hold the engine speed at
3,000 rpm with no load (in Park or Neutral) until
the radiator fan comes on.
•
Let the engine idle for about 5 minutes with the
throttle fully closed and with all electrical items
off.
NOTE: If the radiator fan comes on during this
step, the time when it is operating must not be
incuded in the 5 minutes.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement