Supreme Image

560TVL, 128x WDR

SALES NETWORK

•

SAMSUNG TECHWIN CO., LTD.

145-3, Sangdaewon-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do, 462-120, Korea

TEL : +82-31-740-8132~6 FAX : +82-31-740-8144

•

SAMSUNG OPTO-ELECTRONICS UK, LTD.

Samsung House, 1000 Hillswood Drive, Hillswood Business Park Chertsey, Surrey KT16 OPS

TEL : +44-1932-45-5308 FAX : +44-1932-45-5325 www.samsungtechwin.com

www.samsungcctv.com

P/No. : Z6806083201B

VAN 07. 11

High Resolution WDR V/F Dome Camera SID-560 User’s Manual

Thank you for purchasing a SAMSUNG CCD CAMERA.

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.

ENGLISH

Before operating the camera, confirm the camera model and proper input power voltage. In order to that you can understand this manual thoroughly, we'll introduce our model description.

■ SID-560 SERIES

• NTSC MODEL • PAL MODEL

SID-560N SID-560P

■ MODEL DESCRIPTION

SIGNAL SYSTEM

• SIGNAL SYSTEM

N NTSC MODEL

P PAL MODEL

The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

INFORMATION -This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

WARNING - Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

WARNING - To prevent electric shock and risk of fire hazards:

Do NOT use power sources other than that specified.

Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person and should conform to all local codes.

Features

Ultra High Resolution

By adopting a double-speed 410,000 pixel Sony CCD, the camera produces clear picture quality with a horizontal resolution of 560 TV lines for color, and 700 TV lines for B/W.

Wide Dynamic Range (WDR):

By adopting a proprietary SV-IV DSP chip, the camera delivers clear, high quality pictures even in backlight, by increasing exposure in dark areas while decreasing it in bright areas; a corrected image with clear details results.

Excellent Sensitivity

Adopting a Diagonal 6mm (1/3"), highly sensitive CCD and digital signal processing technology, it can clearly distinguish the outline and color of a subject in an extremely low luminance environment – even, for example, under starlight. Since surveillance is possible in places where the light is poor, the camera is appropriate for day and night surveillance outdoors or on the outside of buildings.

- 0.00004 Lux (B/W Sens-up Mode)

SSNR (Samsung Super Noise

Reduction) Function

The high performance SV-IV DSP chip dramatically reduces the gain noise in digital image processing, producing clear, sharp images in low lighting environments.

Day & Night

The camera identifies whether it is day or night and automatically switches to the appropriate mode, depending on its environment. By day, the camera switches to color mode in order to maintain optimal color. At night, it switches to B/W mode so as to obtain better picture definition.

DIS (Digital Image Stabilizer)

The DIS function compensates for any camera movement, to produce more stable pictures.

Sub Monitor Function

The sub monitor function enables easy adjustment of the camera angle within the monitoring range during its installation.

3-Axis camera mechanism

The SID-560 is especially incredibly flexible to install with its 3-axis camera construction, which makes the camera wall or slope mountable.

Miscellaneous Functions

SENS-UP, FREEZE, FLIP (H/V-REV), D-ZOOM,

SHARPNESS, MOTION DETECTION and PRIVACY functions are provided.

RS-485 Communication

Control Support

Remote OSD menu control via an RS-485 interface is supported.

OSD

The camera control is convenient by using 7 different foreign language O.S.D.

- NTSC : Korean, English, Spanish, Japanese

- PAL : English, French, German, Spanish, Italian, Chinese

Samsung Techwin cares for the environment at all product manufacturing stages to preserve the environment, and is taking a number of steps to provide customers with more environment-friendly products.The Eco mark represents Samsung Techwin s will to create environment-friendly products, and indicates that the product satisfies the EU RoHS Directive.

Warnings & Cautions

This information is provided to ensure your safety and to prevent any losses, financial or otherwise. Please read it carefully and use the product accordingly.

* For product inquiries, please contact the retail shop where you bought the camera. The use of equipment such as an aerial ladder while providing after-sales service shall be at your expense.

* Separate the power plug when thunder crashes or lighting flashes.

* This product is support equipment for surveillance system. Therefore, we can't compensate for material loss and/or personal injuries by robbery, fire, natural disaster or something like this type.

Warning/Attention/Special Mark Messages

Ignoring this information may result in material loss and/or serious personal injuries including death.

Ignoring this information may result in material loss and/or a slight injuries.

Indicates “Never Allowed.” Indicates “No Disassembling.”

Contents

Precautions

Components and Accessories

Overview

Installation

Installation

Adjust the panning and tilting, rotating while watching the monitor

Connection

Connecting To Monitor

Connecting To Power

RS-485 communication control

16

16

17

18

13

13

15

8

10

11

Operating Your Camera

Menu Configuration

Menu Setup

LENS

EXPOSURE

WHITE BALANCE

BACKLIGHT

SSNR

DAY/NIGHT

IMAGE ADJ

SPECIAL

EXIT

Troubleshooting

Specification

Dimension

37

39

40

29

30

32

36

22

24

26

28

19

19

20

21

Precautions

Do not install the camera in extreme temperature conditions.

Do not install or use the camera in an environment where the humidity is high.

Do not drop the camera or subject them to physical shocks.

Never keep the camera face to strong light directly.

Only use the camera under conditions where temperatures are between

-10˚C and +50˚C. Be especially careful to provide ventilation when operating under high temperatures.

It can cause the image quality to be poor.

Do not install the camera under unstable lighting conditions.

Do not touch the front lens of the camera.

It can cause malfunctions to occur.

Do not expose the camera to radioactivity.

It can damage the CCD.

Severe lighting change or flicker can cause the camera to work improperly.

It is one of the most important parts of the camera. Be careful not to be stained by fingerprint.

COLOR CCD CAMERA 8 User’s Manual

If it is exposed to radioactivity, For heated CCD, it will be out of order.

Notes

• If the camera is exposed to spotlight or object reflecting strong light, smear or blooming may occur.

• Please check that the power satisfies the normal specification before connecting the camera.

COLOR CCD CAMERA 9 User’s Manual

Components and Accessories

1. SID-560

2. Instruction Manual

3. M4 Tapping Screw 4EA

4. M4 Machine Screw 4EA

5. Adapter plate

6. Installation Video Output Cable

COLOR CCD CAMERA 10 User’s Manual COLOR CCD CAMERA 11 User’s Manual

Overview

Overview

Pan Base control panning angle of camera

Rotate Base control rotating angle of camera

X2.5 Vari-focal Lens Module

Rotate Base Holding Screw fix rotated position

Pan Base Holding Screws (Color : Silver) fix panned position

RS-485 Control Cable : The detailed description refers to p18

Power Input Jack

Video Output Jack

Function Setup Button

SET Button : Displays the menu on the screen. Press this button to confirm status or after changing a selected item.

Left and Right Button : Used to move the cursor left or right in the menu screen or to change the value of the selected item.

Up and Down Button : Used to move the cursor up or down in the menu screen to select a desired menu item.

Video Output Terminal to Monitor

Dome Cover

Shield Case

Installation

Installation

Notes

• The installation should be done by qualified service personnel or sysytem installers.

• If the ceiling material is not strong enough to hold the installation screws, the camera may fall off. Reinforce the ceiling as needed.

1) Separate the dome cover by clockwise rotation.

2) Separate the shield case by pulling from the camera body.

* To install the dome cover on the camera body, turn the latches in locking direction as shown in the figure 1.

Main Body

(Camera)

Latch

Locking direction

Unlocking direction

(Counterclockwise)

Shield Case

Locking direction

(Clockwise)

Dome cover

[Figure-1]

COLOR CCD CAMERA 12 User’s Manual COLOR CCD CAMERA 13 User’s Manual

Installation

When installing on a adapter plate

An arrow for installing directions adapter plate

M4 tapping screw (provided)

CAMERA

1) Place the bracket provided on the installation surface and fix it with the M4 tapping screws (provided).

(Select either 85X85 or 83.5X46)

2) When placing the camera body on the plate, insert the plate pin into the mounting hole on the body as shown in figure-1 and fix it by turning clockwise.

3) When placing the camera body on the plate, make sure the power and the BNC cables pass through their respective designated holes.(When placing the cable through its side, thread it through the hole at the bottom.)

4) After installation and adjustment of the camera are complete, secure the dome cover by turning it clockwise.

Locking direction

Plate pin

Unlocking direction

Locking direction

Dome cover

Unlocking direction

[Figure-1]

Notes

• Please locate an arrow on bracket for installing direction that you wish to observe

Area and then fix it with the M4 tapping screws.

COLOR CCD CAMERA 14 User’s Manual

Adjust the panning and tilting, rotating while watching the monitor

145˚ 195˚

73˚

170˚

Tilt Base

Rotate Base

Pan Base

-170˚

1) You can adjust camera to any direction by using Pan, Tilt, Rotate mechanism.

• Pan Base moves by 170˚ to each side direction and 340˚ on the whole.

• Tilt Base covers total 146˚ angle(73˚ to each side).

• Angle range of Rotate Base is the same as that of Pan Base. But One side range is 195˚ and another is 145˚.

2) Methods of adjustment

•The case of wall installation

After mounting the camera on a wall, adjusting the panning angle so that the camera can face the direction to monitor when tilting.

And then adjust the tilting angle by rotating the tilt base.

Loosen the rotate base hold screw and adjust rotate base for the best monitoring.

Tighten the rotate base hold screw.

•The case of ceiling installation

After mounting the camera on a ceiling, adjusting the panning angle for better monitoring area by rotating the pan base.

And then adjust the tilting angle by rotating the tilt base.

COLOR CCD CAMERA 15 User’s Manual

Connection

Connecting to Monitor

Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.

Connecting to Power

Connect the adaptor to the power input connector as shown in the figure below. The recommended adaptor specification for SID-500N/SID-500P is DC

12V / 500mA.

CCTV Camera Monitor

• As the connecting method varies with the instruments, refer to the manual supplied with the instrument.

• If necessary, you can connect the monitor to the REMOTE jack on the back of your camera.

• Only connect the cable when the power is turned off.

• Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate device.

Intermediate End monitor

CCTV Camera

COLOR CCD CAMERA 16 User’s Manual

When the resistance value of copper wire is at [20°C(68°F)]

Copper wire size (AWG)

Resistance (Ω / m)

Voltage Drop (V/m)

#24(0.22mm

2 )

0.078

0.028

#22(0.33mm

2 )

0.050

0.018

#20(0.52mm

2 ) #18(0.83mm

2 )

0.030

0.011

0.018

0.006

•As shown in the table above, voltage decreases as the wire gets longer.

Therefore use of an excessively long adaptor output line for connection to the camera may affect the performance of the camera.

*Standard voltage for camera operation : DC 12V ± 10%

*There may be some deviation in voltage drop depending on the type of wire and the manufacturer.

Notes

• Be sure to connect power only after all the installation is complete.

• Note that DC adaptor is not supplied with camera.

• Ground should be connected to the GND terminal.

COLOR CCD CAMERA 17 User’s Manual

Connection

RS-485 communication control

Connecting to RS-485 Control Cable

CONTROL CABLE SPEC

RED (TRX+) RS-485+

WHITE(TRX-) RS-485-

Using a RS-485 communication, it will be able to control the OSD menu at the

SAMSUNG TECHWIN System Controller or DVR.

(1) The case which it controls from the PC

Using a RS-485 converter, It connects to RS-485 control cable outside camera and serial cable

EX) SERIAL PORT OF THE PC(COM1) SERIAL CABLE RS-485 CONVERTER RS-485

CONTROL CABLE

(2)The case which it controls from the DVR or System Controller

It connects the RS-485 control cable in the connection terminal of 485 control boards which are connected with the DVR or System Controller.

485 Control Board Connection Port

(

(+) CONNECTION TERMINAL

) CONNECTION TERMINAL

RS-485 Control Port

RED (TRX+)

WHITE (TRX-)

* RS-485 Communication establishment initial value

Item

Initial value

Camera ID

1

BAUD RATE

9600

UART MODE

8-NONE-1

PET PKT

ENABLE

Notes

• When you construct external control systems for a camera control, please use to the SAMSUNG TECHWIN PROTOCOL or PELCO-D PROTOCOL.

• When you connecting to RS-485 control cable, please peel off the outer skin inside the RS-485 control cable.

COLOR CCD CAMERA 18 User’s Manual

Operating Your Camera

Menu Configuration

LENS

EXPOSURE

WHITE BALANCE

BACKLIGHT

SSNR

DAY/NIGHT

IMAGE ADJUSTMENT

(IMAGE ADJ.)

SPECIAL

Setup Menu

• DC

• SHUTTER • AGC

• RETURN

• ATW • MANUAL

• SENS-UP

• AWC SET

• OUTDOOR • INDOOR

• OFF • WDR

• ON

• COLOR

• OFF

• B/W

• BLC

• FREEZ • V-REV

• D-ZOOM • SHARPNESS

• AUTO

• H-REV

• RETURN

• CAMTITLE • MOTION DET • PRIVACY

• DIS

• RESET

• COMM ADJ • LANGUAGE

• RETURN

EXIT

COLOR CCD CAMERA 19 User’s Manual

Operating Your Camera

Menu Setup

Use the five buttons on back of the camera.

SET button

LEFT button

RIGHT button

UP button

DOWN button

1. Press the SET button.

• Main setup menu is displayed on the monitor screen.

1.LENS

MAIN SETUP

DC

2.EXPOSURE

3.WHITE BAL

4.BACKLIGHT

5.SSNR

6.DAY/NIGHT

7.IMAGE ADJ

ATW

OFF

ON

AUTO

8.SPECIAL

9.EXIT

2. Select a desired function using the Up and Down buttons.

• Place the cursor over a desired item.

COLOR CCD CAMERA 20 User’s Manual

Select the function using the UP or DOWN button.

MAIN SETUP

1.LENS

2.EXPOSURE

3.WHITE BAL

4.BACKLIGHT

5.SSNR

6.DAY/NIGHT

7.IMAGE ADJ

8.SPECIAL

9.EXIT

DC

ATW

OFF

ON

AUTO

Change the status using the LEFT or RIGHT button.

3. Set up a selected item by using the Left and Right buttons.

4. To finish the setting, select ‘EXIT’ and press the SET button.

Notes

• An item with the icon also has sub menus. To select a sub menu, select an item with the icon and press the SET button.

• An item with the - - - icon is unavailable due to function settings.

LENS

Using this function, you can control screen brightness.

1. When the SETUP menu screen is displayed, select LENS by using the Up and

Down buttons so that the arrow indicates LENS .

1.LENS

MAIN SETUP

DC

2.EXPOSURE

3.WHITE BAL

4.BACKLIGHT

5.SSNR

ATW

OFF

ON

COLOR CCD CAMERA 21 User’s Manual

Operating Your Camera

DC : Select Auto Iris Lens

• When DC is selected, you can control screen brightness. The range of brightness control is between 1 and 70. Adjust the brightness appropriately for optimal screen brightness.

EXPOSURE

MAIN SETUP

1.LENS

2.EXPOSURE

DC

3.WHITE BAL

4.BACKLIGHT

ATW

OFF

5.SSNR

ON

1. When the SETUP menu screen is displayed, select EXPOSURE by using the Up and Down buttons so that the arrow indicates EXPOSURE .

2. Select a desired mode using the Up and Down buttons.

SHUTTER : You can select either auto or manual shutter.

- A.FLK : Select this when you experience picture flicker, which can happen when there is a clash with the frequency of the installed lighting.

- ESC : Select this to control the shutter speed automatically. If ESC is selected, the shutter speed is automatically controlled depending on the ambient illumination of the subject.

- MANUAL : You can control shutter speed manually.

Notes

• When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled.

AGC (AUTO GAIN CONTROL) :

The higher the gain level, the brighter the screen - but the higher the noise.

- OFF : Deactivates the AGC function.

- LOW : Allows automatic gain control from 0 to 30dB.

- HIGH : Allows automatic gain control from 0 to 42dB.

SENS-UP :

When it is night or dark, the camera automatically detects the light level and maintains a clear picture if this mode is activated.

- OFF : Deactivates the SENS-UP function.

- AUTO : Activates the SENS-UP function.

COLOR CCD CAMERA 22 User’s Manual COLOR CCD CAMERA 23 User’s Manual

Operating Your Camera

RETURN :

Select this to save the changes in the EXPOSURE menu and return to the SETUP menu.

Notes

• If you press the SET button in ‘AUTO’ mode, You can adjust brightness by increasing or decreasing the shutter speed. (X2~X256)

• Note that the higher the zoom level, the brighter the screen, but the more likely it is that an after-image will appear.

• Although Noise, Spots, and Whitish symptoms may occur in SENS-UP operation when the zoom level is increased, this is normal.

White Balance (White Bal.)

Use the White Balance function to adjust the screen color.

1. When the SETUP menu screen is displayed, select ‘White Bal.’ by using the Up and Down buttons so that the arrow indicates ‘White Bal.’ .

2. Select a desired mode using the Up and Down buttons.

1.LENS

MAIN SETUP

DC

2.EXPOSURE

3.WHITE BAL

4.BACKLIGHT

5.SSNR

6.DAY/NIGHT

ATW

OFF

ON

AUTO

Select one of the following 5 modes, as appropriate for your purpose.

ATW : Select this when the color temperature is between 1800˚K and 10500˚K

INDOOR : Select this when the color temperature is between 4500˚K and 8500˚K.

OUTDOOR : Select this when the color temperature is between 1800˚K and

10500˚K. (sodium light inclusion)

COLOR CCD CAMERA 24 User’s Manual

AWC SET : To find the optimal setting for the current luminance environment in this mode, set the point the camera towards a sheet of white paper and press the SET button. If the environment changes, readjust it.

MANUAL : Select this to fine-tune White Balance manually. Set White Balance first by using the ATW or AWC mode. After that switch to MANUAL mode, fine-tune the White Balance and then press the SET button.

Notes

• White Balance may not work properly under the following conditions. In this case select the AWC mode.

When the color temperature of environment surrounding the subject is out of the control range (e.g. clear sky, or sunset)

When the ambient illumination of the subject is dim.

If the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically, the White Balance operation may become unstable.

COLOR CCD CAMERA 25 User’s Manual

Operating Your Camera

BACKLIGHT

This camera is designed so that it delivers a distinctive subject and background at the same time, even when the subject is in backlight, unlike conventional cameras, by adopting a proprietary SV-IV DSP chip.

1. When the SETUP menu screen is displayed, select ‘BACKLIGHT’ by using the Up and Down buttons so that the arrow indicates BACKLIGHT .

1.LENS

MAIN SETUP

DC

2.EXPOSURE

3.WHITE BAL

4.BACKLIGHT

ATW

OFF

5.SSNR

6.DAY/NIGHT

7.IMAGE ADJ

8.SPECIAL

9.EXIT

ON

AUTO

2. Select a desired mode using the Left and Right buttons depending on the camera purpose.

WDR : When there are both bright and dark areas at the same time, this mode makes both areas distinctive.

OFF : Deactivates the WDR function.

3. Select a desired mode using the Left and Right buttons and press the SET button.

Select WDR to adjust the WDR LIMIT and LEVEL.

- LIMIT : Adjust the WDR Sensitivity by selecting LOW, MIDDLE, or HIGH.

- LEVEL : Adjust the WDR Brightness by controlling the bar from 0 to 100.

Select ‘BLC’ to adjust the area to be enhanced and enhancement level.

WDR OFF

BLC : Enables a user to directly select a desired area from a picture, and to view the area more clearly.

COLOR CCD CAMERA 26 User’s Manual

Notes

• You cannot use the WDR mode when MANUAL or A.FLK mode in ‘SHUTTER’ menu is selected.

• Since the following symptoms may occur according to the ambient illumination when WDR is selected, set it to OFF.

Color or screen changes unnaturally.

Noise appears in the bright part of the screen.

• Since the performance of the WDR function may be affected by the area of the bright part of the screen, optimize the installation angle for the best WDR performance.

• If you increase LIMIT, the screen display may be distorted.

COLOR CCD CAMERA 27 User’s Manual

Operating Your Camera

SSNR

This function reduces the background noise in a low luminance environment.

1. When the SETUP menu screen is displayed, select ’SSNR’ by using the Up and

Down buttons so that the arrow indicates ’SSNR’ .

MAIN SETUP

1.LENS

2.EXPOSURE

DC

3.WHITE BAL

4.BACKLIGHT

ATW

OFF

5.SSNR

6.DAY/NIGHT

ON

AUTO

2. Select a desired mode using the Left and Right buttons.

OFF : Deactivates SSNR. Noise is not reduced.

ON : Activates SSNR so that noise is reduced.

3. Set the SSNR mode to ‘ON’ and press the SET button. Then you can adjust the noise reduction level.

Notes

• You cannot set the SSNR to ‘ON’ or ‘OFF’ when the AGC mode of the EXPOSURE menu is ‘OFF’.

• When adjusting the noise reduction level of the SSNR mode, remember that the higher the level set, the more the noise level will be reduced but that after image may also occur.

COLOR CCD CAMERA 28 User’s Manual

DAY/NIGHT

You can display pictures in color or black and white.

1. When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the Up and Down buttons so that the arrow indicates DAY/NIGHT .

1.LENS

MAIN SETUP

DC

2.EXPOSURE

3.WHITE BAL

4.BACKLIGHT

5.SSNR

6.DAY/NIGHT

7.IMAGE ADJ

ATW

OFF

ON

AUTO

2. Select a desired mode using the Left and Right buttons according to the picture display you want.

COLOR : The picture is always displayed in color.

B/W : The picture is always displayed in black and white.

AUTO : The mode is switched to Color in a normal environment, but switches to

B/W mode when ambient illumination is low. To set up the sswitching time or speed for AUTO mode, press the SET button.

- DWELL TIME : You can select the duration time about changing the day/night mode. 5s, 7s, 10s, 20s, 30s, 40s, 50s, 60s

- DURATION : You can select brightness of illumination about changing the day/night mode.

Fast

Slow

Color B/W B/W Color

2.5 lux 4 lux

0.8 lux 6 lux

* The brightness of illumination is changeable by installed environment.

COLOR CCD CAMERA 29 User’s Manual

Operating Your Camera

EXTERN : This mode allows you to apply a desired filter to external signals.

Notes

• When using a Video Auto Iris Lens, if you set the lens level to low, automatic switching between Color and Black & White may not occur.

• You cannot control the DAY/NIGHT menu when AGC in the EXPOSURE menu is ‘OFF’.

At this time, the exchange between DAY mode and NIGHT mode operates as like selecting ‘COLOR’ mode.

• The OSD key does not work for 3 seconds when switching to Color or B/W, to ensure stable camera operation.

• The camera may focus less well under infrared illumination than under normal illumination.

• Since the camera may not focus as well under infrared illumination at night as it does under normal illumination, install an Extra-low Dispersion Lens to obtain sharp pictures

IMAGE ADJ.

1. When the SETUP menu screen is displayed, select ‘IMAGE ADJ.’ by using the Up and Down buttons so that the arrow indicates IMAGE ADJ.

1.LENS

MAIN SETUP

DC

2.EXPOSURE

3.WHITE BAL

4.BACKLIGHT

5.SSNR

6.DAY/NIGHT

ATW

OFF

ON

AUTO

7.IMAGE ADJ

8.SPECIAL

2. Select a desired mode using the Up and Down buttons.

COLOR CCD CAMERA 30 User’s Manual

IMAGE SETUP

1. FREEZE

2. V-REV

OFF

OFF

3. H-REV

4. D-ZOOM

OFF

OFF

5. SHARPNESS

6. RETURN

ON

FREEZE : You can view still or moving pictures.

V-REV : You can flip the picture vertically on the screen.

H-REV : You can flip the picture horizontally on the screen.

D-ZOOM : You can use a digital zoom of x1~x10.

SHARPNESS :

As you increase this value, the picture outline becomes stronger and clearer. Adjust this value appropriately depending on the sharpness of the picture.

RETURN : Select this to save the settings for the IMAGE ADJ. menu and to return to the SETUP menu.

Notes

• When H-REV or V-REV is selected, any text in the picture also will be flipped horizontally or vertically.

• If you increase the SHARPNESS level too high, the picture may become distorted or noise may appear.

COLOR CCD CAMERA 31 User’s Manual

Operating Your Camera

SPECIAL

1. When the SETUP menu screen is displayed, select ‘SPECIAL’ by using the Up and

Down buttons so that the arrow indicates ‘SPECIAL’.

MAIN SETUP

1.LENS

2.EXPOSURE

DC

3.WHITE BAL

4.BACKLIGHT

ATW

OFF

5.SSNR

6.DAY/NIGHT

ON

AUTO

7.IMAGE ADJ

8.SPECIAL

9.EXIT

2. Select a desired mode using the Up and Down buttons.

SPECIAL

1. CAM TITLE

2. MOTION DET

3. PRIVACY

4. DIS

5. COMM ADJ

6. LANGUAGE

7. RESET

8. RETURN

OFF

OFF

OFF

OFF

ENGLISH

CAM TITLE : If you enter a title, the title will appear on the monitor.

If the SPECIAL menu screen is displayed, use the Up and Down buttons so that the arrow indicates ‘CAM TITLE’.

COLOR CCD CAMERA 32 User’s Manual

Set it to ‘ON’ by using the Left and Right buttons.

SPECIAL

1. CAM TITLE

2. MOTION DET

3. PRIVACY

4. DIS

5. COMM ADJ

6. LANGUAGE

7. RESET

8. RETURN

OFF

OFF

OFF

OFF

ENGLISH

Press the SET button.

Camera ID

A B C D E F G H I J K L M

N O P Q R S T U V W X Y Z a b c d e f g h i j k l m n o p q r s t u v w x y z

- . 1 2 3 4 5 6 7 8 9

C L R P O S E N D

Use the 4 direction buttons to move to a desired letter and select the letter by pressing the SET button. Repeat this to enter multiple letters.

You can enter up to 15 letters.

Notes

• If you move the cursor to CLR and press the SET button, all the letters are deleted. To edit a letter, change the cursor to the bottom left arrow and press the

SET button. Move the cursor over the letter to be edited, move the cursor to the letter to be inserted and then press the SET button.

COLOR CCD CAMERA 33 User’s Manual

Operating Your Camera

Enter a title, move the cursor to ’POS’ and press the SET button. The entered title appears on the screen. Select the position to display the title on the screen by using the 4 direction buttons and press the SET button. When the position is determined, select ’END’ and press the SET button to return to the

SPECIAL menu.

FRONT DOOR

MOTION DET : If you connect an alarm device to this camera, you can monitor activity more efficiently, because a signal is generated by the camera whenever motion is detected.

When the SPECIAL menu screen is displayed, press the Up and Down buttons so that the arrow indicates MOTION DET .

Set up the mode using the 4 direction buttons.

- SENSITIVITY : You can select up to 8 MD areas. When SENSITIVITY number is high, motion detection sensitivity is increased to recognize even small movement.

- AREA MODE : Determines whether to use the MD area selected in SENSITIVITY.

- SEL POS : Determines which of the 4 vertices of each MD area is to be used.

- YPOS : Determines the coordinate of the vertical axis for SEL POS.

- XPOS : Determines the coordinate of the horizontal axis for SEL POS.

- FILL SET : Fills in a selected MD area. Fills in a selected MD area. The color of filling is sequentially selected as brown, orange, blue, cyan, yellowish green, yellow and red.

- RETURN : Select this to save the MOTION DET menu settings and return to the SPECIAL menu.

COLOR CCD CAMERA 34 User’s Manual

Notes

• MD areas show only MOTION DET menu. Therefore, MD areas don’t display on the monitor screen.

• When motion is detected, “MOTION DETECTION” expression is displayed on the screen.

PRIVACY : Hide an area you want to hide on the screen.

When the SPECIAL menu screen is displayed, press the Up and Down buttons so that the arrow indicates ‘PRIVACY’.

Set up the mode using the 4 direction buttons.

- AREA SEL : You can select up to 8 MD areas.

- AREA MODE : Determines whether to use the area selected in the AREA SEL, and the size and position of the area.

- MASK COLOR :Determine area color. You can select Gray, Green, Red, Blue, Black, White.

- TRANSP : Determine the transparency of selected area as controlling number from 0 to 3.

- RETURN : Select this to save the PRIVACY menu settings and return to the

SPECIAL menu.

DIS (Digital Image Stabilizer) :

This function mitigates any picture movement due to external factors such as wind.

Notes

• The chance of resolution decrease is existed because DIS function uses the digital zoom.

• DIS doesn’t operate when background illumination is too low.

• DIS doesn’t operate when object pattern is monotonic as like sky or white wall.

COLOR CCD CAMERA 35 User’s Manual

Operating Your Camera

COMM ADJ (Communication Adjustment):

This function sets up the camera communication status when controlling the camera through an external control device.

When the SPECIAL menu screen is displayed, press the Up and Down buttons so that the arrow indicates ‘COMM ADJ’.

Set up the mode using the 4 direction buttons.

- CAM ID : Determines the camera's identification number (between 0 and 25).

- BAUD RATE : You can select 2400/4800/9600/19200/38400/57600 bps.

- UART MODE : You can select NONE, EVEN or ODD for the parity bits.

- RET PKT : Determines whether to send a command back to the controller device when a communication control command is sent to the camera.

- DISP CAM ID : Display camera title on top left corner of the screen.

LANGUAGE : You can select the menu language according to your requirements.

RESET : Resets the camera settings to the factory defaults.

RETURN : Select this to save the SPECIAL menu settings and return to the SPECIAL menu.

EXIT

Press the SET button in the EXIT menu to save the current settings and exit the SET menu.

COLOR CCD CAMERA 36 User’s Manual

Troubleshooting

Refer to the following table if you are experiencing trouble with your camera.

Contact an authorized technician if the table does not provide you with a solution to the trouble.

Problem

Nothing appears on the screen.

Solution

• Check that the power cord and line connection between the camera and monitor are fixed properly.

• Check that you have properly connected VIDEO cable to the camera VIDEO output jack.

The image on the screen is dim.

The image on the screen is dark.

The camera is not working properly, and the surface of the camera is hot.

• Is lens stained with dirt? Clean your lens with soft, clean cloth.

• Set the monitor to proper condition.

• If the camera is exposed to too strong light, change the camera position.

• Adjust the contrast feature of the monitor.

• If you have an intermediate device, set the 75Ω / Hi-z properly.

• Check that you have properly connected the camera to an appropriate power source.

The DAY/NIGHT menu does not work.

• Check that AGC of EXPOSURE SETUP menu is

‘OFF’.

The SENS-UP function does not work.

• Check that AGC of EXPOSURE SETUP menu is

‘OFF’.

• Check that SHUTTER of EXPOSURE SETUP menu is

‘A.FLK’ or ‘MANUAL’.

COLOR CCD CAMERA 37 User’s Manual

Troubleshooting

Problem

The Motion Detection function does not work.

Color is not correct.

The screen flickers continually.

RS-485 communication fails.

Solution

• Check that MOTION DEF of SPECIAL SETUP menu is ‘OFF’.

• Check the setting of WHITE BAL SETUP menu .

• Check that direction of camera turns toward the

Sun .

• Check the polarity between RS-485 Control Port and RS-485 cable.

485 Control Board Connection Port RS-485 Control Port

(+) CONNECTION TERMINAL (TRX+)

( - ) CONNECTION TERMINAL (TRX-)

485+

485-

• Check the RS-485 Communication establishment initial value

* RS-485 Communication establishment initial value

Item

Initial value

Camera ID

1

BAUD RATE

9600

UART MODE

8-NONE-1

PET PKT

ENABLE

• We recommend that you make ground connect between camera and controller in order to maintain safety communication control.

COLOR CCD CAMERA 38 User’s Manual

Specifications

POWER

CCD

Sync

Input voltage

Power consumption

Size

Total Pixels

Effective Pixels

Scanning System

Frequency

O.S.D

I

C

T

R

E

L

E

C

A

L

WDR

Back-light Compensation

Resolution

S/N (Y signal)

Min. Illumination

White Balance

Electronic Shutter Speed

Sens-up

Gain Control

SSNR

Motion Detection

PRIVACY

V-REV (Mirror)

H-REV (Flip)

FREEZE

SHARPNESS

IRIS Control

Day & Night

DIS

Digital Zoom

Blemish Compensation

Communication

Built-in Lens

Lens angle of view

Monitoring PAN angle TILT

Operating

Temperature/Humidity

Storage

Temperature/Humidity

Dimension

Weight

SID-560N SID-560P

DC12V

2.5W

Diagonal 6mm (1/3") Sony DS CCD

811(H) x 508(V)

768(H) x 494(V)

795(H) x 595(V)

752(H) x 582(V)

Horizontal:15.734 KHz

Vertical:59.94 Hz

Korean, English, Japanese,

Spanish

2:1 Interlace

Horizontal:15.625 KHz,

Vertical:50.00 Hz

English, French, Germany, Spanish,

Italy, Chinese

52 dB

ON / OFF

Color : 560 TV Lines B/W : 700 TV Lines

52 dB (AGC Off, Weight ON)

0.001 Lux (Color Sens-up), 0.00004 Lux (B/W Sens-up) at F1.2

ATW / AWC / Manual / Outdoor / Indoor (1800˚K ~10,500˚K)

1/60 ~ 1/120,000 sec 1/50 ~ 1/120,000 sec

AUTO / OFF (Selectable limit x2 ~ x256)

LOW/HIGH/OFF

ON / OFF (1~32 Level)

ON / OFF (8 Zone, ALARM Output)

ON / OFF (8 Zone)

ON / OFF

ON / OFF

ON / OFF

ON / OFF (Level Adjustable)

DC drive Lens

COLOR / Black& White / AUTO

ON / OFF

ON / OFF (x10)

256 point (Even 128 Point, Odd 128 Point)

RS-485 (2400, 4800, 9600, 19200, 38400, 57600 bps selectable)

(STW Protocol, Pelco-D Protocol available) x2.5 Vari-focal Lens (F1.2 f3.8~9.5mm)

37.3˚ ~ 95.5˚

Manual 0˚ ~ 340˚

Manual 0˚ ~ 146˚

-10˚C to +50˚C / 30% to 80% RH

-20˚C to +60˚C / 20% to 90% RH

Ø141.2 X 105.5 mm

525g

COLOR CCD CAMERA 39 User’s Manual

Dimension

R48

Ø141.2

108mm

COLOR CCD CAMERA 40 User’s Manual

105.5mm

DECLARATION OF CONFORMITY

Application of Council Directive(s) 89 / 336 / EEC

Manufacturer's Name SAMSUNG TECHWIN CO., LTD

Manufacturer's Address SAMSUNG TECHWIN CO., LTD

42, SUNGJU-DONG CHANGWON-CITY,

KYUNGNAM, KOREA, 641-716

European Representative Name

European Representative Address

Equipment Type/Environment

Model Name

Beginning Serial NO.

Year of Manufacture

Conformance to

CCTV Camera

SID-560

S712001

2007. 12. 1

EN 50081-1 : 1992

EMC-Directive 89/336 EEC and 92/31/EEC

EN 50130-4 : 1996

We, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s).

Manufacturer SAMSUNG TECHWIN CO., LTD Legal Representative in Europe

Signature Signature

Full Name

Position

YOUNG TAEK SON Full Name

QUALITY CONTROL MANAGER Position

Date 2007. 12 .1

Place

Date

MEMO